operation guide - henry schein · treatment mode remove hand piece from the hand piece holder....

An Acne Technology For Immediate Results

Operation Guide

TheraClear

© Theravant Corp, 2014. Do not distribute without permission

Treatment Modes

Two Mechanisms of Action

Vacuum & Light Mechanism

Uses Regular or Small Inserts

Acne Surgery Mechanism

Uses Plastic Insert with Needle


Pneumatics deep cleans pores by extracting build up of sebaceous material

Obstruction in the pilosebaceous apparatus is removed and skin normalizes

TheraClear hand piece makes full contact with treatment area

Along with targeting heating of the dermis, the endogenous effect of light activates porphryns to destroy P. acnes and reduces sebum production

TheraClear Treats the Causes of Acne.


Pneumatics pull acne lesion into needle, opening access to lesion

Sebum is forced out by the pressure difference .

Removal of Sebum immediately reduces size of lesion.

TheraClear hand piece makes full contact with treatment area

New Extraction Insert Enhances and Speeds Results


This first section illustrates the following features.

Turning the system on

Entering the pass code

Setting treatment parameters

Treatment Mode

Turning System Off

TheraClear Basic Operation


TURN ON POWER

Turn the power switch located on the rear panel to the ON position.

The Keypad screen, pictured on the next slide, will appear after a few seconds.

Starting the TheraClear


ENTER PASS CODE

Next enter pass code 1410

Press the enter key at lower right of Keypad.

Use the back arrow at lower left if you make a mistake.




Standby Mode

System enters Standby Mode.


Standby Mode

Set Treatment Parameters

Skin Types I to IV

Energy Level 6

Vacuum Level 2

Double Pulse

750 Between Pulses

Use Arrow Keys to Increase/Decrease Parameters.

Press on Orange Area For Double Pulse

Press Space Between Pulses to Change Time Between Pulses.

Decreases Parameter Increases Parameter

Adjusts Time Between Pulses

Set Double Pulse


Standby Mode


Skin Type V

Energy Level 4

Vacuum Level 2

Double Pulse

750 Between Pulses


Press on Orange Area For Double Pulse

Press Space Between Pulses to Change Time Between Pulses.


Set Double Pulse

Adjusts Time Between Pulses


Standby Mode


Skin Type VI

Energy Level 2

Vacuum Level 2

Single Pulse




Treatment Mode

Hand Switch

Treatment Mode

Remove hand piece from the hand piece holder.

Enter Treatment mode by pressing and releasing the hand switch.

Approximately two seconds after pressing the hand switch, the light on the hand piece will change from blue to green.

The Treatment indicator (light bulb icon) will appear on the touch screen.

System is in Treatment Mode.


Treatment Mode

Hand Switch

Treatment Mode

Remove hand piece from the hand piece holder.

Enter Treatment mode by pressing and releasing the hand switch.

Approximately two seconds after pressing the hand switch, the light on the hand piece will change from blue to green.

The Treatment indicator (light bulb icon) will appear on the touch screen.

System is in Treatment Mode.

Light Bulb Icon


Soft Vacuum Settings

Hand Switch

Soft Vacuum Settings

Activate by Pressing on Vacuum Number.

Letter “S” appears in Front of Number

Press Again to Return to Regular Vacuum

Use on Forehead.

Use on Sensitive Skin Areas

Soft Vacuum Button


Return to Standby Mode

Hand Switch

Return to Standby Mode

Return to Standby Mode by pressing and releasing the hand switch.

The light on the hand piece will change from green to blue.

The Treatment indicator (light bulb icon) will disappear on the touch screen.

Repalce hand piece in the hand piece holder.

System is in Standby Mode.


Vacuum Extraction

Treatment Modes

Light & Vacuum


Procedure • Treat the Lesion with the acne needle insert.

• Vacuum Extraction set at 3 seconds. • Needs the Time Mode RFID

• Treat the Lesion with Vacuum Only. (Optional)

• Vacuum Extraction set at 3 seconds

• Treat the Lesion with Vacuum & Light • Double Pulse Mode • Energy level 6 • Vacuum Level 2

• Treat the Entire Face with Vacuum & Light (Optional)

• Double Pulse Mode • Energy level 6 (Skin Type Dependent) • Vacuum Level 2

Acne Surgery Protocol


Shutting Off System

Hand Switch

Sleep Mode

Press the TheraClear logo button (the Sleep Button) located at the bottom of the screen.

Pressing this Button places the system in a state in which a pass code needs to be entered before the system can be used again.

Next press the sleep icon.

System is in Sleep Mode.


TURN OFF POWER

Turn power switch located on the rear panel to the Off position.

System can be powered off from Standby Mode, Treatment Mode or Sleep Mode.

Powering Off the TheraClear


This section illustrates the following features.

Installing the Inserts

Installing the Acne Surgery inserts

Using the RFID for installing Pulses

Using the RFID for installing Time Segments

TheraClear Inserts


Regular Size for Majority of the Face

Smaller Size for Noise and Above Lip

Acne Surgery Insert

The regular and small insert sell for $15 a piece. Sold in boxes of 10. Should last for 10 or more treatments

Acne Surgery Insert sells for $9.90 Plastic part can be autoclaved Needle is single patient use.

Treatment Inserts


Treatment Inserts

Installing Inserts

Press Insert into Aperture

Insert Should be Snug

Remove by Pulling Insert out of Aperture


Inserts are Used Per Patient and Cleaned Between Uses

Place system in standby or OFF mode. Remove the Insert from the handpiece.

Clean all sides and surfaces of the Insert with a Sani Cloth ™

A Q-tip may be used to better reach the insides of the Insert


Debris Remains on the Lower Edge of Insert For Easy Cleaning

Skin does not touch the uppermost part of insert keeping it free of evacuated debris Skin debris remains

in lower part of insert

Skin Elevated into Treatment Insert


Acne Surgery Insert


Easy to Install Tip


Treatment


operation guide - henry schein · treatment mode remove hand piece from the hand piece holder....

Documents