operating and parts manual - dalton ag

OPERATING AND PARTS MANUALMobility 100 Spreader

2019

DaltonAg.com 800.342.7498602 E. Van Buren Lenox, Iowa 50851100% Employee Owned

TABLE OF CONTENTS

TO YOU THE OWNER................................................................................................................................ 1LIMITED WARRANTY STATEMENT............................................................................................................. 2NEW MACHINE CHECKOUT....................................................................................................................... 3OPERATION AND SAFETY.......................................................................................................................... 4LUBRICATION SCHEDULE.......................................................................................................................... 5LUBRICATION DETAIL............................................................................................................................... 6MACHINE ADJUSTMENT.......................................................................................................................... 7SPECIFICATIONS....................................................................................................................................... 8SPREAD ADJUSTMENT & APPLICATION RATES........................................................................................ 9SPREAD PATTERN DETAILS....................................................................................................................... 10STANDARD SPREAD SETUP...................................................................................................................... 11DISTRIBUTOR BLADE TUNING................................................................................................................. 1240’ SPREAD.............................................................................................................................................. 1350’ SPREAD.............................................................................................................................................. 14FRAME & DRIVELINE................................................................................................................................ 15540 PTO.................................................................................................................................................... 161000 PTO.................................................................................................................................................. 176 BOLT, HEAVY HUB ASSEMBLY................................................................................................................. 18GROUND DRIVE ASSEMBLY..................................................................................................................... 19-20FRONT TANK ASSEMBLY............................................................................................................................ 21REAR AREA ASSEMBLY............................................................................................................................ 22-23DISTRIBUTOR GEAR BOX.......................................................................................................................... 24HYDRAULIC SPINNER GEAR BOX.............................................................................................................. 25TRACTOR HYDRAULIC DRIVEN SPINNERS................................................................................................. 26VARIABLE CONTROL, ELECTRICAL PLAN.................................................................................................... 27CONVEYOR CLUTCH OPTION................................................................................................................ 28-29TRACTOR HYDRAULIC DRIVEN SPINNERS.................................................................................................. 30BOLT TORQUE CHART................................................................................................................................ 31VARIABLE RATE CONTROL, HYDRAULIC PLAN............................................................................................ 32BANDER OPTION........................................................................................................................................ 33PARTS ORDERING PROCEDURE.................................................................................................................. 34

1

TO YOU, THE OWNER

Your Dalton Ag Equipment is the most modern, up-to-date, versatile, machine available for fertilizer application. The machine is the result of many years of experience, research, development and testing of equipment for fertilizer application. It is soundly engineered and carefully built to rigid specifications. It is of rugged and simple construction, with a minimum of moving parts.

However, to obtain maximum performance from your Dalton Ag Equipment, it is necessary to follow the instructions and safety suggestions in this manual. Each section has been carefully prepared for the purpose of providing needed and valuable information to the owner and operator. Each operator of this unit should be familiar with the contents of this manual. Keep it in a safe and convenient location. THERE ARE MANY SAFETY SUGGESTIONS (CAUTION AREAS) PRINTED THROUGHOUT THIS MANUAL. CAREFULLY READ THEM ALL BEFORE OPERATING THIS UNIT.

DESIGN IMPROVEMENTS

Dalton Ag Products follows a policy of continuous products improvement. We therefore reserve the right to make design improvements, and changes in specifications and prices, without incurring obligations to make revisions or additions to equipment previously sold.

REGISTER WARRANTY

ONE OF FOUR WAYS

• Register on-line at: www.daltonag.com• Fax your completed warranty registration form to: 641-333-4429• Email your completed warranty registration form to: [email protected]• Mail your completed warranty registration form to: Dalton Ag, Inc. P.O. Box 70 Lenox, IA 50851

2

LIMITED WARRANTY STATEMENT

3

NEW MACHINE CHECKOUT

Before attempting to use or operate the spreader it is important to be thoroughly familiarized with the contents of this manual. Then the machine should be checked using the following check list:

1. Ground drive tire inflated to 22 PSI. Tires inflated to manufacturing specifications.

2. All bearings lubricated and tightly mounted with collars securely locked. (See lubrication schedule page 5.)

3. Conveyor chains, drive chain & ground drive chain adjusted to correct tension. Conveyor chain should be flush or just below the bottom of the trough in the area approximately 2’ behind the front roller.

4. Sprockets tightened & in proper alignment.

5. Inspect entire machine for loose bolts, especially in the spinner assembly and drive line area.

6. Distributor fan blades set properly. (See spread adjustment and application rates)

7. Setting of metering gate. With the pointer on the number 1 of the spread rate chart decal, the lower edge of the metering gate should be 1 ¼” above the trough floor.

8. Tighten wheel bolts daily – 95 foot pounds single axle spreaders.

9. Check drive line for ease of operation by turning shaft by hand. If the foregoing inspection reveals that additional lubrication or adjustment is required, refer to the proper section of this manual for detailed instructions.

10. Ground drive wheel and universal joint shear pins in place and tight.

11. Check both spinner gear boxes for oil; fill to level of pipe plug with SAE No. 90 non-detergent oil.

4

OPERATION

SPREADER SAFETY

Before starting in motion please read the following words of caution.A. It is recommended that initial spreading be done in as low a range as possible to permit easy break-in.B. Always shut off or disconnect power to spreader before attempting to repair or adjust the spreader.C. Do not transport machine with ground drive wheel engaged.D. NEVER back-up spreader with ground drive wheel engaged.E. Make sure that the towing vehicle brakes are operating properly and are capable of stopping the towing vehicle.F. If a pick-up is used as the towing vehicle, it is wise to add ballast for additional safety and traction. We

recommend that all towing vehicles be ballast loaded to their recommended G.V.W.G. Hitches should be of heavy construction and should be welded or bolted directly to the towing vehicle frame.

Hitches should be checked routinely for loose bolts, cracked welds, etc.H. Never tow a spreader with a drawbar pin less than 1” in diameter. Pins should also have a locking device.I. Do not tow spreader at speeds in excess of 20 mph loaded or 40 mph empty.J. Remember, that the stopping and braking distances vary with load and vehicle speed. It is well to familiarize

yourself with the characteristics of your machine under different load and speed conditions.K. Be sure to attach safety break-away chain and the safety chain to towing vehicle to assure control of spreader in

the case of pin or hitch failure.L. The unit is designed for hitching to vehicles with drawbar heights between 12 and 18 inches above the ground

level. It will operate with all standard tractor hitches and PTO’s. WARNING: Hydraulically mounted drawbars must be securely and mechanically locked because a fully loaded spreader applies a load in the order of 2000 lbs. to the hitch.

M. WARNING: Remember this unit is designed for agricultural use only and is primarily an off-the-road vehicle and should be towed at tractor speeds ONLY, not to exceed 20 mph loaded or 40 mph empty. Inspect hubs routinely to see if they are heating, which indicates either a need for lubrication or improper adjustment of brakes or bearings, also check stud nuts for tightness.

N. WARNING: The maximum capacity of this unit is 6 tons (600) or 200 cubic feet, based on a material density of 60 pounds per cubic foot. DO NOT EXCEED THIS LIMIT!

OPERATING INSTRUCTIONS

Please read the following completely before spreading.

1) Attach spreader to towing vehicle, make sure hitch and hitch pin are sound.2) Attach PTO shaft to proper rpm PTO.3) Spinner discs, adjustable chute and conveyor floor should be clean for accurate metering.4) Set metering gate to desired spread rate according to decal on the back end sheet of tank. Always keep the

machine in the lowest possible range.5) Before starting to spread, rotate the ground drive wheel several revolutions by hand to make sure the conveyor

chain is operating freely. If chain is frozen or moves with too much resistance, correct problem before using spreader.

6) If the ground drive wheel operates properly, check with chain and sprocket arrangement for desired range setting and chain tension.

7) When spreading is complete, disengage ground drive assembly from the tire and install transport lockup.

5

(4) BEARINGS(2) U-JOINTS(1) BEARING(4) U-JOINTS(2) TELESCOPING TUBES

CONVEYOR DRIVE ALL MODELS (6) BEARINGS(2) SHAFT HOUSINGS(2) U-JOINTSTELESCOPING TUBE(2) SQUIRTS OF SAE 90 OIL INTO JACK CRANKOIL CAP

CHAINS OIL LUBRICATE PIN JOINTS WITH SAE 80-90PTO SHAFT GREASE (2) U-JOINTS AND SLIP TUBE

SPINNER GEARBOX GREASEUNIVERSAL GREASE ON EACH FITTING UNDER SPINNER HUB

DRIVE SHAFT SPLINES

SPINNER GEAR BOX

WHEEL BEARINGS

GEAR BOXES

REPLACE WORN OR FAILED PARTSTIGHTEN LOOSE BOLTS

TOUCH-UP PAINT

DAILY LUBRICATION SCHEDULE

WEEKLY LUBRICATION SCHEDULE

MONTHLY LUBRICATION SCHEDULE

ANNUAL LUBRICATION SCHEDULE

DRIVELINE

GROUND DRIVE

ALL MODELS

GROUND DRIVE

ADJUST TENSION OF CONVEYOUR AND DRIVE CHAINS (SEE MACHINE CHECKOUT)

CHECK GROUND DRIVE TIRE INFLATION (22 PSI)CORRECT BELT TENSIONWEEKLY

SEMI-ANNUALLY

WASH SPREADER

DRAIN, FLUSH, AND REFILL WITH SAE 90 OIL

Pay particular attention to the daily cleaning and greasing of the telescoping tube assembly.

ALL MODELS

COAT WITH GREASE OR ANTI-SEIZE COMPOUNDCHECK TO SEE THAT OIL LEVEL IS UP TO OIL LEVEL PLUG. USE SAE 90 OIL

REPACK

LUBRICATION SCHEDULE

MAINTENANCE SCHEDULE

6

LUBRICATION DETAIL

A

99

44

4

4

4

4

446

6

7

5

3

DETAIL A SCALE 4 : 30

44

4

4

3

1

LUBRICATION SCHEDULE1 SLIP JOINT DAILY2 PIVOT BUSHING EVERY 10 HRS3 UNIVERSAL JOINT EVERY 15 HRS4 BALL BEARING EVERY 15 HRS5 ACTUATOR EVERY 15 HRS6 SPINNER HUB EVERY 15 HRS7 GEAR BOX EVERY 75 HRS8 GATE JACK (OIL) WEEKLY9 WHEEL BEARING TWICE A YEAR

CHECKED BY

Sheet1 A

RICH SMOTHERS

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF DALTON AG. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE

WRITTEN PERMISSION OF DALTON AG IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:26

Default7/28/2014

2/9/2010

SHEET 1 OF 1

LUBRICATION SCHEDULE

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8

w w w . D a l t o n A g . c o m

7

MACHINE ADJUSTMENT

WHEEL BEARING ADJUSTMENT

After repacking or when inspecting wheel bearings, the following adjustment procedure should be followed. Place flat

washer and spindle nut on spindle. Turn hub as you tighten nut. When a pronounced drag is felt in the bearings, back

off nut one complete slot. If necessary continue to back off the nut until the next slot aligns with the cotter pin hole and

install cotter pin and dust cap.

CONVEYOR CHAIN ADJUSTMENT

Loosen chain take-up locking nuts on outside of front end of trough. Adjust take-up bolts evenly until chain clears main

frame members and axle tube by ¾” ½”. Inspect shaft bearing mounting bolts and shaft locking collars for tightness of set

screws (6 places). Reset take-up locking nuts.

STORAGE

Before storing the spreader for more than a few days, the machine should be emptied completely and thoroughly

washed both inside and out. This precaution will minimize the severity of fertilizer acid corrosion, extend the useful life

of the machine, and prevent damage to drive line and conveyor chain from fertilizer compaction and caking. We further

recommend that the machine be thoroughly greased after washing.

Before operating the machine after extended periods of storage, re-lubricate the entire spreader in accordance with the

lubrication section of this manual. Also check the entire spreader, following the New Machine Checkout Procedure to be

found in a foregoing section of the manual.

Remember that oil and grease are your least expensive corrosion inhibitors.

ADDITIONAL INSTRUCTIONS:The ground drive is equipped with the following sprocket combinations: Low Range - Drive chain on 12 & 72 Tooth Sprockets. High Range - Drive chain on 24 & 48 Tooth Sprockets.

CAUTION

Do not operate your spreader with less than one and a half (1 1/2) inch of metering gate opening as material will com-pact against metering gate and cause failure of the conveyor chain.

CAUTION

Do not disconnect implement from tractor with material remaining in box.

9

SPREAD ADJUSTMENT AND APPLICATION RATES

For accurate and precise spreading rates, it is necessary that you know the weight in pounds per cubic foot of the material to be spread. If this is not known, the weight can be quickly and accurately determined by the following method:

1. Weigh an empty one gallon container.2. Fill level full with the material to be used.3. Weigh container and material, and then subtract the weight of the container to obtain the weight of the

material.4. Multiply the weight of the material by 7.5 to obtain the weight of the material in pounds per cubic foot.

Example: Typical Material-Potash

1) Weight of empty one gallon container 1.00 lbs.2) Weight of filled container 10.35 lbs.3) Weight of container (net) 9.35 lbs.4) 9.35 X 7.5 70.125 lbs. /cu ft.

You would therefore use the column on the Spread Chart headed 70 to determine the proper gate opening for the desired application rate.

Your Mobility Spreader with its heavy-duty distributor discs and blades will apply most materials in a 50 foot wide swath.

10

SPREAD PATTERN DETAILS

An operational characteristic of this type of machine is the possibility of overloading the distributors at high rates of application. Such an overload results in an alteration of the spread pattern to a narrower swath with heavier application at the center. This can be avoided by reducing speed when using high application rates. MOBILITY DISTRIBUTORS ARE DESIGNED FOR A MAXIMUM APPLICATION RATE OF 1500 POUNDS PER MINUTE OF AVERAGE 60 POUND PER CUBIC FOOT MATERIAL. Caution: Be extra careful to check your spread pattern when using high application rates. Adjust your driving pattern to the actual delivered spread swath, the adjustment of the machine, and the material being used. Recommended ground or travel speed for most application rates (up to 700 pounds per acre) is 8 mph. When application rates are in excess of 700 pounds per acre, the ground speed should be proportionately reduced, (for example, at 1400 pounds per acre, maximum ground speed should be 4 mph.) We recommend that for very high application rates, to insure uniformity of application, that two lighter application passes be made preferably placing your second pass over the lap lines of the first pass. This also is recommended practice when spreading under very windy conditions or with a material that segregates easily. If your effective spread pattern is more than 50 feet wide the Metering Gate setting should be increased proportionately, according to the percentage of your spread width in excess of 50 feet. The gate setting should likewise be decreased if your effective spread pattern is less than 50 feet. EXAMPLE: 60 foot effective spread width—increase gate setting from Spread Chart by 20%; 40 foot effective spread pattern width—decrease your gate setting from Spread Chart setting by 20%. Your spread pattern can be checked accurately and visually on a freshly worked, level area of ground. Such an area is also ideally suited to adjusting and fine tuning your machine. The following diagram graphically illustrates a typical spread pattern.

Note on the illustration below that the lap point occurs at the point where the application rate is one-half of the spread chart rate. The profile of the spread pattern tapers at both edges and has a wide uniform area in the center. By careful attention to the lap point during application, a very uniform and even spread rate can be attained. The Mobility Spreaders have been designed to provide this good and uniform tapered profile to make spread width less critical. However, excessive or insufficient overlap of passes will result in a poor application pat-tern in the lap area of the total spread pattern. If you can attain this spread pattern and pay careful attention to the lap points, the dotted line on the illustration will represent your actual overall spread pattern.

11

STANDARD SPREAD SETUP

1 53

97

42

68

VIEWED FROM BACK OF SPREADER

ROTATIONROTATION

STANDARD SPREAD, BLADE SETUP# PART NUMBER QTY.1 1003727 DISTRIBUTOR DISC 2

2 MS 1001662 EXTRA LONG DISTRIBUTOR BLADE, 8, RIGHT 1

3 MS 1001705 EXTRA LONG DISTRIBUTOR BLADE, 8, LEFT 1

4 MS 1001718 7 INCH DISTRIBUTOR BLADE, RIGHT 1

5 MS 1001719 7 INCH DISTRIBUTOR BLADE, LEFT 1

6 MS 1001924 4.375 DISTRIBUTOR BLADE, RIGHT 1

7 MS 1001925 4.375 DISTRIBUTOR BLADE, LEFT 1

8 MS 1001926 DISTRIBUTOR BLADE, 5.5, RIGHT 1

9 MS 1001927 DISTRIBUTOR BLADE, 5.5, LEFT 1

10 120393 WASHER, .3125 16

CHECKED BY

Sheet1 A

RICH SMOTHERS




DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:6

STANDARD SPREAD PATERN, BLADE SETUP11/17/2015

9/16/2013

SHEET 1 OF 1

STANDARD SPREAD, BLADE SETUP

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8


12

DISTRIBUTOR BLADE TUNING

FINE TUNING OF DISTRIBUTOR AND BLADE SETTINGS

All Mobility Spreaders are given an average standard factory setting of distributor blades. Such a setting, of course, cannot be perfect for all field conditions and materials. The following information will be helpful in adjusting the distributor blades on your machine to give optimum performance for your specific conditions.

Your spread pattern will be affected by 1) the material used, 2) the distributor blade setting, and 3) the rotation speed of the distributors. The distributors are designed to be operated at 750 RPM (540 tractor P.T.O. RPM). A plus or minus 10% change in distributor RPM will increase or decrease spread pattern width accordingly. An increase in PTO RPM will tend to deposit less material at the center of the spread pattern, while a decrease will deposit more material at the center. The physical characteristics of the materials being spread, which are important to the spread pattern, include bulk density, particle size, particle shape, physical strength and rugosity or surface roughness. For best performance it is recommended that you fine tune your machine to the material being used. The spreading profile and spread swath width can be changed drastically by alteration of the setting of the distributor blades. The drawing on the next page shows had blades may be extended from or retracted toward the center of the disc. Also, the angle of bladeintersection with a radius of the disc may be altered. They may be advanced toward coincidence with the disc radius or retarded away from it. Further, blade lengths are not all equal. These adjustments affect the spread pattern in the following ways:

1. Advance long blades--more material to the outside of spread pattern; also will increase spread pattern width.

2. Retard long blades--opposite effect of above.3. Advance short blades—helps eliminate problem of streaking in the middle of spread pattern.4. Retard short blades—puts more material in the center of spread pattern.5. Extend blades away from center of spinner—increases spread width somewhat.6. Retract blades (more towards center of spinner)—opposite effect of above.7. Moving flow divider (or chute) toward the front of spreader will tend to put more material in center of

spread pattern. This is because material is deposited on outer edge of spinner causing it to leave earlier.8. Moving divider toward the rear of the spreader has the opposite effect.

VIEWED FROM BACK OF SPREADER

ROTATIONROTATION

EXTENDED BLADE

RETRACTED BLADE RETARDED BLADE

ADVANCED BLADE

DISTRIBUTOR BLADE TUNING, MOBILITY

CHECKED BY

Sheet1 A

RICH SMOTHERS




DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:6

STANDARD SPREAD PATERN, BLADE SETUP11/17/2015

9/16/2013

SHEET 1 OF 1

DISTRIBUTOR BLADE TUNING, MOBILITY

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8


13

800.342.7498 LOW RANGE 12 TO 72 T.

40 45 50 55 60 65 70 751 55 63 69 76 83 90 96 104

1.5 83 93 103 114 124 135 145 1552 110 124 138 151 165 179 193 206

2.5 138 155 171 189 206 224 240 2583 165 186 206 228 248 269 289 310

3.5 193 216 241 265 289 314 338 3594 220 248 275 303 330 358 385 413

4.5 248 279 310 341 371 403 434 4645 275 310 344 379 413 448 481 516

HIGH RANGE 24 TO 48 T.

40 45 50 55 60 65 70 751 165 186 206 228 248 269 290 310

1.5 248 279 310 341 371 404 435 4652 330 371 413 454 495 538 580 620

2.5 413 464 515 568 619 673 725 7753 495 558 619 681 743 806 869 930

3.5 578 650 721 794 866 941 1014 10854 660 743 825 908 990 1075 1158 1240

4.5 743 836 929 1021 1114 1210 1303 13945 825 929 1031 1135 1238 1344 1448 1550

APPLICATION RATE EXPRESSED IN POUNDS PER ACRE

PART NO. 1001118-40

NOTICEAPPROXIMATELY 40 FT. SPREAD

GATE OPENING

MATERIAL WEIGHT IN POUNDS PER CUBIC FOOT

GATE OPENING


40’ SPREAD

14

50’ SPREAD

800.342.7498 LOW RANGE 12 TO 72 T.

40 45 50 55 60 65 70 751 44 50 55 61 66 72 77 83

1.5 66 74 82 91 99 108 116 1242 88 99 110 121 132 143 154 165

2.5 110 124 137 151 165 179 192 2063 132 149 165 182 198 215 231 248

3.5 154 173 193 212 231 251 270 2874 176 198 220 242 264 286 308 330

4.5 198 223 248 273 297 322 347 3715 220 248 275 303 330 358 385 413

HIGH RANGE 24 TO 48 T.

40 45 50 55 60 65 70 751 132 149 165 182 198 215 232 248

1.5 198 223 248 273 297 323 348 3722 264 297 330 363 396 430 464 496

2.5 330 371 412 454 495 538 580 6203 396 446 495 545 594 645 695 744

3.5 462 520 577 635 693 753 811 8684 528 594 660 726 792 860 926 992

4.5 594 669 743 817 891 968 1042 11155 660 743 825 908 990 1075 1158 1240

APPLICATION RATE EXPRESSED IN POUNDS PER ACRE

PART NO. 1001118

NOTICEAPPROXIMATELY 50 FT. SPREAD

GATE OPENING


GATE OPENING


15

FRAME AND DRIVELINE

30

26

25

1322

24

2

4

5

7

8

23

3

18

1727

10

6

16

21

20

9

11

12

1

2914

15

15

19

1528

1514

8

**1000 RPM OPTION***

# PART NUMBER Q6 4440854 1000 RPM PTO SHAFT 1

28 4440827 PULLEY, 4.75 DIA 1

29 4440828 PULLEY, 8.25 DIA 1

# PART NUMBER Q1 MS 1001764 PTO FRONT SHIELD 12 MS 4432185 SHAFT, FRONT, 52.5, MOB 100 & 150 13 MS 1004197 SHAFT 14 4432188 SHAFT, BACK, 1 x 16.75, MOB 100 & 150 15 641667 U-JOINT, DRIVE SHAFT 26 1009228 PTO COMPLETE, 540 12N 17 101689 SPRING PIN .375x2 38 150008 NUT, .5 NC, PLTD 89 150011 NUT, .625 NC, LOCKING, PLTD 2

10 150022 NUT, .375, LOCKING, PLTD 111 150046 NUT, .375 NC SS 412 150211 FLAT WASHER, .375 813 150212 FLAT WASHER, .375 PLTD 214 150218 LOCK WASHER, .5, PLTD 815 150220 FLAT WASHER, .5 PLTD 16

# PART NUMBER Q16 151805 BOLT, .375 NC x 1.25, PLTD 417 151813 BOLT, .375 NC x 2.5, G5, PLTD 118 152210 BOLT .5 x 2 NC PLN 419 152212 BOLT .5 x 2.5 NC PLN 420 152417 BOLT .625 x 5 NC PLN 221 155248 LOCK WASHER, .375 422 158039 LOCK NUT, .4375 223 640511 PILLOW BLOCK BEARING 424 1001636 SPRING 225 1001885 CARRIAGE BOLT, .4375 x 6 226 1007099 BELT 127 4440234 TALL 2000 LBS JACK 128 4440829 PULLEY, 6.25 DIA 129 4440830 PULLEY, 6.75 DIA 130 MS 4432198 BEARING ARM, MOB 100 & 150 1

CHECKED BY

Sheet1 A

RICH SMOTHERS




DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:25

FRAME & DRIVELINE11/13/2014

9/22/2014

SHEET 1 OF 1

MOBILITY 100 & 150, FRAME & DRIVELINE

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8


16

540 PTO

1001739 PTO HALF 12 N FEMALE, IMPLEMENT W SHIELD

1001738 PTO HALF, MALE TRACTOR HALF W SHIELD

1011253 PTO SHIELD ONLY, OUTER w RETAINER

1011252 PTO SHIELD ONLY, INNER w RETAINER

1001730 REPAIR KIT, U-JOINT, 12N

1002434 RETAINER KIT, 12N

1009228 PTO COMPLETE, 540 12N

640452 LOCK PIN REPAIR KIT

1004186 PTO SHEILD KIT

CHECKED BY

Sheet1 A

RICH SMOTHERS




DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:10

Default7/28/2014

7/7/2014

SHEET 1 OF 1

1009228 540 RPM PTO SHAFT OPTION

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8


17

1000 PTO

1001739 PTO HALF 12 N FEMALE, IMPLEMENT W SHIELD

4440853 PTO HALF, MALE, TRACTOR

1011253 PTO SHIELD ONLY, OUTER w RETAINER

1011252 PTO SHIELD ONLY, INNER w RETAINER

1001730 REPAIR KIT, U-JOINT, 12N

1002434 RETAINER KIT, 12N

4440854 1000 RPM PTO SHAFT

1011258 PTO KIT, SNAP HITCH 1000 RPM

1004186 PTO SHIELD KIT

CHECKED BY

Sheet1 A

RICH SMOTHERS

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF

CMC-DALTON AG. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CMC-DALTON

AG IS PROHIBITED.


DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:10

Default12/24/2015

7/7/2014

SHEET 1 OF 1


F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8



18

6 BOLT, HEAVY HUB ASSEMBLY

4410

087

6 BO

LT H

EAVY

, HUB

ASS

EMBL

Y, C

OM

PLET

E

1403

67 S

EAL

1403

06 B

EARI

NG

1403

68 R

AC

E

6401

54 S

TUD

, .5

X 2

1401

85 R

AC

E64

0155

LUG

NUT

, .5

6400

49 B

EARI

NG

1403

64 S

PIN

DLE

WA

SHER

, 1 IN

CH

1403

63 S

LOTT

ED N

UT, 1

NC

4440

736

CO

TTER

PIN

, .18

75 X

3

1402

29 D

UST

CA

P 50

2200

2

6205

57 6

BO

LT H

EAVY

HUB

W R

AC

ES

4410

087

6 BO

LT H

EAV

Y, H

UB A

SSEM

BLY,

CO

MPL

ETE

SHEE

T 1

OF

1

9/4/

2014

12/1

3/20

17EX

PLO

DED

VIE

W

SCA

LE: 1

:4

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H S

MO

THER

S

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

Shee

t1

CHE

CKE

D B

Y

4410

087

6 BO

LT H

EAV

Y, H

UB A

SSEM

BLY,

CO

MPL

ETE

ASS

EMBL

Y

19

GROUND DRIVE ASSEMBLY

1000

504

SPRO

CKE

T, 1

2 TO

OTH

1002

425

AD

JUST

MEN

T H

AN

DLE

1502

18 L

OC

K W

ASH

ER, .

5, P

LTD

1502

20 F

LAT

WA

SHER

, .5

PLTD

1000

923

IDLE

R BL

OC

K

1516

08 B

OLT

, .31

25X2

NC

PLT

D

1002

309

WH

EEL,

DRI

VE

SHA

FT

1502

06 L

OC

K W

ASH

ER, .

3125

MED

SPG

PLT

D15

0019

NUT

, .31

25 N

C G

8 PL

TD

1001

402

GRO

UND

DRI

VE

SHA

FT

1016

89 S

PRIN

G P

IN .3

75X2

1001

865

BEA

RIN

G, 1

INC

H B

ORE

1000

503

SPRO

CKE

T, 4

8 TO

OTH

1000

505

SPRO

CKE

T, 2

4 TO

OTH

1000

502

SPRO

CKE

T, 7

2 TO

OTH

RC 1

0018

57 R

C #

40 S

S

4420

675

GRO

UND

DRI

VE,

MA

LE,

W U

-JO

INT,

1 T

ON

4420

676

GRO

UND

DRI

VE,

FEM

ALE

, 1 T

ON

4420

681

GRO

UND

DRI

VE,

FE

MA

LE, 1

.5 T

ON

4420

682

GRO

UND

DRI

VE,

M

ALE

, W U

-JO

INT,

1.5

TO

N

MO

BILI

TY 1

00

MO

BILI

TY 1

50

1001

631

CA

RRIA

GE

BOLT

, .5-

13X5

1001

658

WH

EEL

ASS

EMBL

Y10

0166

1 W

HEE

L10

0165

9 TIR

E

1000

786

KEY,

.25

X .2

5 X

1.5

GRO

UND

DRI

VE,

MO

BILIT

Y 10

0 &

150

SHEE

T 1 O

F 1

9/22

/201

4

2/26

/201

5EX

PLO

DED

VIE

W

SCA

LE: 1

:10

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H S

MO

THER

S

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

Shee

t1

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

GRO

UND

DRI

VE,

MO

BILIT

Y 10

0 &

150

20

GROUND DRIVE ASSEMBLY

GRO

UND

DRIV

E, 1

00 &

150

, MA

NUA

L O

N-O

FF

8

1 6 2 94

6

7

3

ALL

QUA

NTIT

IES

(Q) A

RE P

ER A

SSEM

BLY

GRO

UND

DRIV

E, 1

00 &

150

, HYD

RAUL

IC O

N-O

FF

14

10

1213

1118

1719

1718

19

#PA

RT N

UMBE

RQ

1M

S 10

0519

2 H

AN

DLE

WEL

DM

ENT,

G

ROUN

D D

RIV

E, U

PPER

1

2M

S 10

0519

1 TH

REA

DED

RO

D

WEL

DM

ENT,

GRO

UND

DRI

VE

1

3M

S 44

2068

3 G

ROUN

D D

RIV

E,

MA

NUA

L, 1

00 &

150

1

4M

S 10

0804

6 RE

TAIN

ER H

AN

DLE

W

ELD

MEN

T, G

ROUN

D D

RIV

E1

610

0151

4 SP

RIN

G, G

ROUN

D D

RIV

E1

613

1017

FLA

T W

ASH

ER, .

751

712

0393

WA

SHER

, .31

252

810

0247

8 RO

LL P

IN, .

1875

x 1

.51

910

0241

8 C

OTT

ER P

IN, .

0938

x .7

51

#PA

RT N

UMBE

RQ

10M

S 44

2048

2 G

ROUN

D D

RIV

E, H

YD,

100

& 1

501

1144

3326

6 C

YLIN

DER

LO

CK

1

1244

4088

4 H

YDRA

ULIC

CYL

IND

ER, 2

x 4

x

1.12

51

1344

4086

5 LO

CK

PIN

, SQ

UARE

WIR

E1

1444

3326

5 BU

SHIN

G, 1

.25

SCH

40

X 2

1

1715

0211

FLA

T W

ASH

ER, .

375

4

1815

1811

BO

LT, .

375

NC

x 2

, G5,

PLT

D2

19M

S 44

3319

6 A

DJU

STA

BLE

LUG

, G

ROUN

D D

RIV

E TO

P1

1815

5248

LO

CK

WA

SHER

, .37

52

1915

0046

NUT

, .37

5 N

C S

S2

GRO

UND

DRI

VE,

100

& 1

50, O

N-O

FF

SHEE

T 1 O

F 1

9/22

/201

4

11/1

2/20

14EX

PLO

DED

VIE

W

SCA

LE: 1

:8

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H S

MO

THER

S

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

Shee

t1

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

GRO

UND

DRI

VE,

100

& 1

50, O

N-O

FF

21

FRONT TANK ASSEMBLY

1

11

9

8

11

3

8

5

6

4

12

2

10

8

87

10

** FITTED VINYL TARPS **

# PART NUMBER Q1 MS 4420678 TARP POLE, 100 AND 150 12 2001001 FRONT ROLLER 13 MS 4420481 CONVEYOR SHIELD, WELDMENT, 100 & 150 14 640519 BOLT, TAKE UP 25 1000956 CONVEYOR SPLICE PIN 16 4440906 DRAG CHAIN, 100, 150 MOB 17 120233 BOLT, .375 NC x 1, SS 38 150212 FLAT WASHER, .375 PLTD 139 158023 BOLT, .375 x 1.5, NC, S.S. 410 150046 NUT, .375 NC SS 711 155248 LOCK WASHER, .375 712 640079 BEARING, TAKE-UP 2

PART NUMBER Q4440907 TARP,

WITH CORD, MOB 100 12001129 TARP,

WITH CORD, MOB 150 1

CHECKED BY

Sheet1 A

RICH SMOTHERS




DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:20

FRONT TANK ASSEMBLY11/12/2014

9/22/2014

SHEET 1 OF 1

FRONT TANK ASSEMBLY, MOB 100 & 150

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8


22

REAR AREA ASSEMBLY

60

65

9

513

11

54

1050

4159 44

69

58

4 15 1418 24

16

23

26

23 2517

22

2

45

63

12

652

64

4947

49

6557

68

66

3330

29

40

32

6261

5 31

5757

5265

5254

53

5757

52 65

1

4442

48

5767

52

5554

5452

65

28

13

7

MO

BILIT

Y 10

0 &

150

REA

R A

REA

ASS

EMBL

Y

SHEE

T 1

OF

2

9/22

/201

4

2/26

/201

5RE

AR

ARE

A A

SSEM

BLY

SCA

LE: 1

:20

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H SM

OTH

ERS

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

Shee

t1

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

MO

BILIT

Y 10

0 &

150

REA

R A

REA

ASS

EMBL

Y

23

REAR AREA ASSEMBLY, 100 & 150 SERIES SPREADERS

** 1004466 DISTRIBUTOR BLADE SET ** INCLUDES BOTH RIGHT SIDE

AND LEFT SIDE BLADES.

# PART NUMBER Q1 4420681 GROUND DRIVE, FEMALE, 1.5 TON 1

1A 4420676 GROUND DRIVE, FEMALE, 1 TON 12 1000961 #50 CHAIN IDLER WELDMENT 13 1004557 GATE JACK WELDMENT 14 1001717 DISC CAP WELDMENT R.H. 15 1001716 DISC CAP WELDMENT L.H 16 1008033 BUMPER WELDMENT 17 1000838 DRIVE SPROCKET ASSEMBLY 19 1000644 SPROCKET SHAFT 1

10 158035 ROLL PIN .3125 x 3.5 211 1000684 CAST SPROCKET, MACHINED 112 MS 1001379 DIVIDER WELDMENT 113 1003734 DISTRIBUTOR DISC ASSEMBLY, RH 114 1003727 DISTRIBUTOR DISC 115 MS 1001718 7 INCH DISTRIBUTOR BLADE, RIGHT 116 MS 1001924 4.375 DISTRIBUTOR BLADE, RIGHT 117 MS 1001662 EXTRA LONG DISTRIBUTOR BLADE, 8, RIGHT 118 MS 1001926 DISTRIBUTOR BLADE, 5.5, RIGHT 119 151603 .3125x1 NC PLTD BOLT 420 150209 LOCK WASHER, .375, PLTD 421 150019 NUT, .3125 NC G8 PLTD 422 151407 BOLT, .25 NC x .75 PLTD 623 150204 FLAT WASHER, .25 PLTD 1624 150202 LOCK WASHER, .25 PLTD 825 150024 NUT, .25 NC, PLTD 826 1003709 SPINNER HUB, STANDARD 127 151419 BOLT, .25x1.25 HH NC PLTD 228 1003733 DISTRIBUTOR DISC ASSEMBLY, L.H. 129 1003727 DISTRIBUTOR DISC 130 MS 1001925 4.375 DISTRIBUTOR BLADE, LEFT 131 MS 1001927 DISTRIBUTOR BLADE, 5.5, LEFT 132 MS 1001719 7 INCH DISTRIBUTOR BLADE, LEFT 133 MS 1001705 EXTRA LONG DISTRIBUTOR BLADE, 8, LEFT 134 150019 NUT, .3125 NC G8 PLTD 1235 150209 LOCK WASHER, .375, PLTD 436 151602 BOLT .3125 x .75 NC PLTD 1037 1010175 BOLT .3125 x 1 NC 238 150208 WASHER, .3125 STD Z PLTD 1639 150206 LOCK WASHER, .3125 MED SPG PLTD 840 1003709 SPINNER HUB, STANDARD 141 640034 BEARING, 1 INCH BORE 2-BOLT 142 1000646 BEARING, 1.25 BORE 2-BOLT FLANGE 244 641653 KEY, .25 x .25 x 1.25 245 151801 BOLT, .375 NC x .75, PLTD 847 150206 LOCK WASHER, .3125 MED SPG PLTD 348 151603 .3125x1 NC PLTD BOLT 349 150208 WASHER, .3125 STD Z PLTD 950 151807 BOLT .375 x 1.5 NC PLN 651 151806 BOLT, .375 NC x 1.5, G5, PLTD 252 150209 LOCK WASHER, .375, PLTD 2753 120233 BOLT, .375 NC x 1, SS 654 150212 FLAT WASHER, .375 PLTD 1455 151802 BOLT, .375 NC x 1, PLTD 157 150211 FLAT WASHER, .375 2158 1000507 SPROCKET 50B36 159 1000506 SPROCKET, 50B12 160 150124 NUT, NF, SS 261 150226 LOCK WASHER, .75, PLTD 262 150227 FLAT WASHER, .75 PLTD 263 1003737 GEAR BOX SET 164 MS 1001501 DIVIDER 165 150046 NUT, .375 NC SS 1966 MS 4432191 TROUGH BACK 167 150614 BOLT, .375x1 NC PLTD 468 1001633 LOCK NUT, .3125 369 1001455 CHAIN #50 1

CHECKED BY

Sheet2 A

RICH SMOTHERS




DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV

SCALE: 1:20 SHEET 2 OF 2

MOBILITY 100 & 150 REAR AREA ASSEMBLY

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8


24

1003737, DISTRIBUTOR GEAR BOX

ITEM

PART

#D

ESC

RIPT

ION

QTY

110

0373

5BO

X A

SSEM

BLY,

RH

12

1000

938

PLU

G, S

OFT

23

1000

932

BEA

RIN

G8

410

0242

6G

EAR

25

1000

936

HO

USI

NG

, RH

16

1006

856

OIL

PLU

G2

710

0093

5K

EY, W

OO

DRU

FF2

810

0373

0SH

AFT

, TA

PERE

D1

910

0093

3RE

TAIN

ER R

ING

510

1000

931

RETA

INER

RIN

G8

1110

0093

0SE

AL

312

1001

206

TUBE

ASS

EMBL

Y1

1310

0094

4H

OU

SIN

G B

ARR

EL3

1410

0094

1TU

BE A

SSEM

BLY

115

1002

417

SHA

FT, T

APE

RED

116

1000

945

PIN

ION

GEA

R2

1710

0373

6BO

X A

SSEM

BLY,

LH

118

1003

730

SHA

FT, T

APE

RED

119

1000

947

HO

USI

NG

, LH

120

1001

205

BARR

EL A

SSEM

BLY

121

1000

948

SHA

FT &

GEA

R A

SSEM

BLY

122

1000

940

GA

SKET

323

1000

834

HH

CS,

5/1

6-18

x 3

/4”

1224

1000

836

LOC

K W

ASH

ER, 5

/16”

1225

1003

742

45 D

EGRE

E G

REA

SE Z

ERK

2

25

HYDRAULIC SPINNER GEAR BOX

1008

463

CO

UPLI

NG

, HA

LF, 1

BR

1008

464

CO

UPLI

NG

, CHA

IN, #

60

1008

462

CO

UPLI

NG

, HA

LF, .

625

BR10

0845

9 BR

AC

KET,

MO

TOR

MO

UNT

MS

1008

458

DOUB

LE S

PIN

NER

MO

TOR

MO

UNT

1008

758

HYDR

AUL

IC M

OTO

R

1003

737

GEA

R BO

X SE

T

60-I-

SS #

60 S

S C

ON

NEC

TING

LIN

K

6416

53 K

EY, .

25 x

.25

x 1.

25

1500

05 N

UT, .

375

NC

, PLT

D15

0209

LO

CK

WA

SHER

, .37

5, P

LTD

1502

12 F

LAT W

ASH

ER, .

375

PLTD

1502

02 L

OC

K W

ASH

ER, .

25 P

LTD

1514

07 B

OLT

, .25

NC

x .7

5 PL

TD

1502

12 F

LAT W

ASH

ER, .

375

PLTD

1502

09 L

OC

K W

ASH

ER, .

375,

PLT

D15

0005

NUT

, .37

5 N

C, P

LTD

1502

12 F

LAT W

ASH

ER, .

375

PLTD

1518

06 B

OLT

, .37

5 N

C x

1.5

, G5,

PLT

D

1518

05 B

OLT

, .37

5 N

C x

1.2

5, P

LTD

SEA

L KI

T FO

R HY

DRA

ULIC

MO

TOR

PART

# 1

0112

64-1

ROW

CRO

P HY

D S

PIN

NER

S

SHEE

T 1 O

F 1

4/3/

2013

7/28

/201

4D

efau

lt

SCA

LE: 1

:5

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H SM

OTH

ERS

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

Shee

t1

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

ROW

CRO

P HY

D S

PIN

NER

S

26

TRACTOR HYDRAULIC DRIVEN SPINNERS

B

A

FRO

M T

RAC

TOR

RETU

RN T

O

TRA

CTO

R

CLO

SED

CEN

TER

OPE

N C

ENTE

R

POW

ER5

4

3

11

1

7

10

6

1112

23

3

2

5

7

8

9

9

9

9

4

1008

758

HYD

RAUL

IC M

OTO

R

12

13

13

5

5

FAC

TORY

SET

TO

750

RPM

DO N

OT A

DJUS

T

TRA

CTO

R HY

DRA

ULIC

DRI

VEN

SPI

NN

ERS,

RO

W

CRO

P

SHEE

T 1

OF

2

9/2/

2009

7/28

/201

4D

efau

lt

SCA

LE: 1

:4

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H S

MO

THER

S

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

SCH

EMA

TIC

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

TRA

CTO

R HY

DRA

ULIC

DRI

VEN

SPI

NN

ERS,

RO

W C

ROP

27

VARIABLE RATE CONTROL, ELECTRICAL PLAN

CHECKED BY

ELECTRICAL PLUMBING

602 E. VAN BUREN ST., LENOX, IA 50851

A

RICH SMOTHERS

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF

CMC-DALTON AG. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CMC-DALTON

AG IS PROHIBITED.


DRAWN BY

CONFIG.PRINT DATE

COMMENTS:DWG:

SIZE

ASHEET TITLE: REV


VARIABLE RATE CONTROL, ELECTRICAL PLAN

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8

28

CONVEYOR CLUTCH OPTION

1001969 CLUTCH JAW ASSEMBLY: INCLUDES ITEM NOS. 12, 14, 15, 16, 19 & 33***ITEM NO. 9 FOR MOBILITY 150: 1000523-150 DRIVE SHAFT***

# PART NUMBER QUANTITY1 640034 BEARING, 1 INCH BORE 2-BOLT 12 640034 BEARING, 1 INCH BORE 2-BOLT 13 150212 FLAT WASHER, .375 PLTD 94 150046 NUT, .375 NC SS 55 4420692 ARM WELDMENT, SHORT 16 4432204 CROSS SHAFT 17 4420691 ENGAGING ARM WELDMENT, SHORT 18 1001975 TRIP ARM WELDMENT 19 1000523-100 DRIVE SHAFT 1

10 Backup of 158015 ROLL PIN, .3125 x 2 111 155248 LOCK WASHER, .375 212 1001954 DRIVE JAW, WELDMENT 113 1001957 BUSHING, SHIFTING FORK CLUTCH 214 150201 LOCK WASHER, .25 MED SPG PLN 215 1001959 BEARING, .50 BORE 2 BOLT FLANGE 116 150024 NUT, .25 NC, PLTD 217 151419 BOLT, .25x1.25 HH NC PLTD 218 150204 FLAT WASHER, .25 PLTD 419 150218 LOCK WASHER, .5, PLTD 120 151802 BOLT, .375 NC x 1, PLTD 121 150005 NUT, .375 NC, PLTD 322 1001958 BUSHING, SHIFTING ARM, CLUTCH 223 151805 BOLT, .375 NC x 1.25, PLTD 224 152003 BOLT .4375 x 1.25 NC PLTD 125 150220 FLAT WASHER, .5 PLTD 226 150021 NUT, .4375 NC PLATED 127 150217 LOCK WASHER, .5 128 3 CHAIN LINK 129 1001522 EXTENSION SPRING, .75 x 12.5 130 151809 BOLT .375 x 1.75 NC Z PLTD 231 150248 LOCK WASHER, .375 STD SS 632 158023 BOLT, .375 x 1.5, NC, S.S. 333 152249 BOLT .5 x 1.5 NC GRD 5 PLTD 134 1004324 PULLEY, SINGLE SHEAVE, 1.5 INCH 1

CHECKED BY

Sheet2 A

RICH SMOTHERS




DRAWN BY

CONFIG.PRINT DATE

COMMENTS: DWG:

SIZE

ASHEET TITLE: REV


CONVEYOR CLUTCH OPTION

F O R P A R T S , C A L L 1 . 8 0 0 . 3 4 2 . 7 4 9 8


29

126

10

9

4

31

28

332

34

25

27

26

23

3

22

8

20

5

724

2523

322

3

11

4

3319

29

18 13

3121

2131 17

21

32

331

430

3

431

3

330

16

1514

1001

969

CLU

TCH

JAW

ASS

EMBL

Y

CO

NV

EYO

R C

LUTC

H O

PTIO

N

SHEE

T 1

OF

2

10/2

2/20

14

3/2/

2015

REM

OTE

CLU

TCH

SCA

LE: 1

:6

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H SM

OTH

ERS

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

Shee

t1

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

CO

NV

EYO

R C

LUTC

H O

PTIO

N

CONVEYOR CLUTCH OPTIONMOBILITY 100 & 150

30

ITEM

NO

.PA

RT N

UMBE

RQ

TY.

1FC

51-3

4, H

YDRA

ULIC

REG

ULA

TOR

1

256

02-1

2 T

CO

UPLE

R, F

-F-M

, .75

INC

H N

PT2

355

02-1

2 ST

ELB

OW

, 90

DEG

REE,

.5 IN

CH

3

454

0412

-8, 2

INC

H A

DA

PTER

, .5I

NC

H-.7

5 IN

CH

NPT

3

580

10-4

PIO

NEE

R FI

TTIN

G, .

5 IN

CH

4

664

1679

RES

TRIC

TOR,

.06,

.5 IN

CH

NPT

1

7PM

R10

CHE

CK

VA

LVE,

.5 IN

CH

NPT

2

814

0412

-8 A

DA

PTER

, .5-

.75

INC

H N

PT2

9HO

SE, .

375

INC

H6

1040

50-1

2 PI

ON

EER

FITT

ING

, FEM

ALE

, .5

INC

H N

PT1

1116

03-8

-8 T

CO

UPLE

R, .5

INC

H N

PT2

1254

04-8

, 2 IN

CH

NIP

PLE,

.5IN

CH

NPT

2

13.5

O R

ING

FITT

ING

2

TRA

CTO

R HY

DRA

ULIC

DRI

VEN

SPI

NN

ERS,

RO

W

CRO

P, p

2 SHEE

T 1 O

F 1

SCA

LE: 1

:4

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H SM

OTH

ERS

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

BILL

OF

MA

TERI

ALS

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

TRA

CTO

R HY

DRA

ULIC

DRI

VEN

SPI

NN

ERS,

RO

W C

ROP,

p2

31

IMPORTANT : Over tightening hardware can be as damaging as under tightening.Tightening beyond recommended torque will reduce the fastener’s shock load capacity.

WARNING: Never work around any raised implement while in the raised position without using safety lockups.

32

VARIABLE RATE CONTROL, HYDRAULIC PLAN

4441

047,

HYD

RAUL

IC M

OTO

R, 1

01 1

040

009

TO F

RON

T OR

BOTT

OM

PO

RT O

F M

OTO

R

TO R

EAR

OR

TOP

PORT

OF

MO

TOR

RETU

RN TO

FRO

M

6901

12-

8 EL

BOW

FITT

ING

TRA

CTO

R

6900

12-

8 ST

RAIG

HT F

ITTIN

G

TRA

CTO

RFA

ST V

ALVE

063

017

3 16

2

1

CHE

CKE

D BY

F O R

P

A R

T S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

3

RIC

H SM

OTH

ERS

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

A

VARI

ABL

E RA

TE C

ONT

ROL,

HYDR

AUL

IC P

LAN

SHEE

T 1 O

F 1

4/12

/201

2

4/11

/201

7FO

R D

WG

SCA

LE: 1

:3

REV

SHEE

T TITL

E:

ASIZE

2

HYD

RAUL

IC P

LUM

BIN

G

45

PRO

HIBI

TED.

DW

G:

CO

MM

ENTS

:

PRIN

T DA

TEC

ONF

IG.

DRA

WN

BY

PRO

PRIET

ARY

AND

CO

NFID

ENTIA

LTH

E IN

FORM

ATIO

N C

ONT

AINE

D IN

THIS

DRAW

ING

IS TH

E SO

LE P

ROPE

RTY

OF

DALT

ON

AG. A

NY R

EPRO

DUC

TION

IN

PART

OR

AS A

WHO

LE W

ITHO

UT TH

E W

RITT

EN P

ERM

ISSIO

N O

F DA

LTO

N AG

IS

VARI

ABL

E RA

TE C

ONT

ROL,

HYDR

AUL

IC P

LAN

08G

-8M

PX H

OSE

END

33

BANDER OPTION

MS

4410

306

SPRE

ADE

R BA

NDE

R

MS

4410

307

100

HOPP

ER E

XTEN

SIO

N5

4

3

1

6

7

2

MS

4410

308

150

HOPP

ER E

XTEN

SIO

N

8 1211

10

9

13

14

#PA

RT N

UMBE

RQ

1M

S 44

3219

3 M

OB.

100

EXT

ENSI

ON

, FR

ON

T &

BA

CK

2

2M

S 44

3219

4 10

0 &

150

SID

E EX

TEN

SIO

N2

3M

S 44

3219

5 EX

TEN

SIO

N B

RAC

KET

44

1502

12 F

LAT

WA

SHER

, .37

5 PL

TD76

512

0233

BO

LT, .

375

NC

x 1

, SS

386

1552

48 L

OC

K W

ASH

ER, .

375

387

1500

46 N

UT, .

375

NC

SS

38

#PA

RT N

UMBE

RQ

8M

S 44

3219

6 M

OB.

150

EXT

ENSI

ON

, FR

ON

T &

BA

CK

2

9M

S 44

3219

4 10

0 &

150

SID

E EX

TEN

SIO

N2

10M

S 44

3219

5 EX

TEN

SIO

N B

RAC

KET

411

1502

12 F

LAT

WA

SHER

, .37

5 PL

TD76

1212

0233

BO

LT, .

375

NC

x 1

, SS

3813

1552

48 L

OC

K W

ASH

ER, .

375

3814

1500

46 N

UT, .

375

NC

SS

38

MO

BILIT

Y 10

0 &

150

AD

D-O

NS

SHEE

T 1 O

F 1

10/2

9/20

14

11/1

3/20

14D

efau

lt

SCA

LE: 1

:25

REV

SHEE

T TIT

LE:

ASIZE

DW

G:

CO

MM

ENTS

:

PRIN

T D

ATE

CO

NFI

G.

DRA

WN

BY

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

LTH

E IN

FORM

ATIO

N C

ON

TAIN

ED IN

THI

S D

RAW

ING

IS T

HE S

OLE

PRO

PERT

Y O

F D

ALT

ON

AG

. AN

Y RE

PRO

DUC

TION

IN

PART

OR

AS

A W

HOLE

WITH

OUT

THE

W

RITT

EN P

ERM

ISSI

ON

OF

DA

LTO

N A

G IS

PR

OHI

BITE

D.

54

32

1

RIC

H SM

OTH

ERS

A

602

E. V

AN

BUR

EN S

T., L

ENO

X, IA

508

51

Shee

t1

CHE

CKE

D B

Y

F O

R

P A

R T

S ,

C A

L L

1 . 8

0 0

. 3

4 2

. 7 4

9 8

MO

BILIT

Y 10

0 &

150

AD

D-O

NS

34

PARTS ORDERING PROCEDURE

Your Dalton Ag dealer is interested in your new fertilizer application equipment and has the desire to help you get the most value from it. Through the help of this manual, you will find you can do some of the regular maintenance yourself. For parts and service, contact the Dalton Ag Dealership from which you purchased your fertilizer application equipment or your local Dalton Ag dealer.

When replacement parts are required, consult the applicable illustration and parts list to obtain the correct part name and number. When requesting a replacement part, always include the following information:

1. Complete Part Number 2. Description 3. Quantity Required 4. Machine and Model Number 5. Machine Serial Number - located on the topside of the frame near hitch 6. Provide complete name and address for where and how parts are to be shipped.

NOTE: Right and left hand parts and sides of the units are determined by standing at the rear and facing in the direction of forward travel.

EQUIPMENT MODEL:___________________________________

EQUIPMENT SERIAL NO.:________________________________

DATE OF PURCHASE:___________________________________

NAME OF DEALER:_____________________________________

DEALER’S PHONE NUMBER:______________________________

Thank you for your business!DaltonAg.com 800.342.7498602 E. Van Buren Lenox, Iowa 50851

100% Employee Owned

35

NOTES

36

NOTES

www.daltonag.com

602 E. VAN BUREN / LENOX, IOWA 50851 / 800-342-7498

operating and parts manual - dalton ag

Documents