olympus vr-370 manual en
TRANSCRIPT
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 1/78
DIGITAL CAMERA
Instruction Manual
VR-370/D-785
● Thank you for purchasing an Olympus digital camera. Before you start to use your new camera, pleaseread these instructions carefully to enjoy optimum performance and a longer service life. Keep thismanual in a safe place for future reference.
● We recommend that you take test shots to get accustomed to your camera before taking important
photographs.● In the interest of continually improving products, Olympus reserves the right to update or modify
information contained in this manual.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 2/78
2 EN
Checking the contents of the box
ames of PartsNames of Parts
3
4
1
2
9
10
8
6
5
7
1 Strap eyelet
2 Multi-connector
3 Battery/card cover
4 Battery/card compartment lock
5 Flash
6 Self-timer lamp/AF illuminator
7 Lens
8 Microphone
9 Tripod socket
10 Speaker
or
Digital camera Strap Lithium Ion
Battery (LI-50B)
USB-AC adapter
(F-2AC)
USB cable
(CB-USB7)
OLYMPUS
Setup CD-ROM
Other accessories not shown: Warranty card
Contents may vary depending on purchase location.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 3/78
3 EN
3
2
1 4
7
5
6
8
9
10
1 n button
2 Shutter button
3 Monitor
4 Zoom lever
5 R button (shooting movies)
6 q button (switching between
shooting and playback)
7 Indicator lamp
8 Arrow pad
INFO (changing information
display)
(erase)
9 A button (OK)
10 button
Attaching the camera strapAttaching the camera strap
Pull the strap tight so that it does not come
loose.
Arrow pad
H (left)
G (down)
F (up)
I (right)
FGHI instruct to press the up/down/left/right
arrow pad.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 4/78
4 EN
Inserting and removing the
battery and card (commercially
available)
1 Follow Steps1 and2 to openthe battery/card cover.
Battery/card compartment lock
1
2
Battery/card cover
Turn off the camera before opening the battery/
card cover.
2 Insert the battery while sliding thebattery lock knob in the directionof the arrow.
Battery lock knob
Insert the battery as illustrated with theC mark
toward the battery lock knob.
Damage to the battery exterior (scratches, etc.)
may produce heat or an explosion.
Slide the battery lock knob in the direction of thearrow to unlock, and then remove the battery.
3 Insert the card straight until itclicks into place.
Write-protect switch
Always use SD/SDHC/SDXC cards or Eye-Fi
card with this camera. Do not insert other types
of memory cards. “Using the card” (p. 62)
● Do not touch the metallic parts of the card directly.
To remove the cardTo remove the card
2 1
Press the card in until it clicks and comes out slightly,
then remove the card.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 5/78
5 EN
4 Follow Steps1 and2 to closethe battery/card cover.
2
11
When using the camera, be sure to close and
lock the battery/card cover.
Charging the battery
Connect the USB cable and USB-AC adapter to the
camera and charge the battery.
For charging the battery abroad, see “Using your
charger and USB-AC adapter abroad” (p. 61).
● The battery is not fully charged at shipment. Before
use, be sure to charge the battery until the indicatorlamp turns off (up to 4 hours).
Connecting the cameraConnecting the camera
Indicator lamp
On: Charging
Off: Charged
AC outlet
or
USB cable(supplied)
Multi-connector
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 6/78
6 EN
When to charge the batteriesWhen to charge the batteries
Charge the battery when the error message shown
below appears.
Battery Empty
Error message
Flashes in red
Never use any cable other than supplied or
Olympus-designated USB cable. This may cause
smoking or burning.
The included F-2AC USB-AC adapter (hereafter
referred to as USB-AC adapter) differs
depending on the region where you purchasedthe camera. If you received a plug-in type USB-
AC adapter, plug it directly into AC outlet.
The included USB-AC adapter has been
designed to be used for charging and playback.
Do not take pictures while the USB-AC adapter
is connected to the camera.
Be sure to unplug the power plug of the USB-ACadapter from the wall outlet when the charging is
complete or the playback ends.
For details on the battery, see “Battery Handling
Precautions” (p. 70). For details on the USB-AC
adapter, see “USB-AC adapter” (p. 71).
● If the indicator lamp does not light, check the USB
cable and USB-AC adapter connections.
● The battery can be charged while the camera is
connected to the computer via USB. The charging
time varies depending on the performance of the
computer. (There may be cases in which it takes
approx. 10 hours.)
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 7/78
7 EN
Turning on the camera and
making the initial settings
When you turn on the camera for the first time, a
screen appears enabling to set the language for themenus and messages displayed in the monitor, and
the date and time.
To change the selected date and time, see “Setting
the date and time d [X]” (p. 40).
1 Press the n button to turnon the camera, pressFGHI
of the arrow pad to select yourlanguage and press theA button.
2 PressFG of the arrow pad toselect the year for [Y].
X MENUBack
Y/ M/ D
Y M D Time
-- -- -- --:..2013
Date and time setting
screen
3 PressI of the arrow pad to savethe setting for [Y].
X MENUBack
Y/ M/ D
Y M D Time
-- -- -- --:..2013
4 As in Steps 2 and 3, press
FGHI of the arrow pad toset [M] (month), [D] (day), [Time](hours and minutes), and [Y/M/D](date order), and then press theA button.
For precise time setting, press theA button as
the time signal strikes 00 seconds.
5 PressHI of the arrow pad toselect time zone and then presstheA button.
● UseFG to turn daylight saving time
([Summer]) on or off.
Summer
’13.02.26 12:30 MENUBack
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 8/78
8 EN
Learning how to use the
camera
● Press the n button to turn on the camera and
enter the standby mode. (Press the n buttonagain to turn off the camera.)
● Select the shooting mode, and press the shutter
button to shoot a still image.
● To shoot a movie, press theR button.
● Set the shooting functions using the function
menu or the setup menu.
● To view images, press theq button to switch to
playback mode. ● To return to standby mode, press theq button
again, or press the shutter button halfway down
and then release it.
● Press and hold theq button while the camera is
turned off to start up the camera in the playback
mode.
● In this case, pressing theq button again sets
the camera to the standby mode.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 9/78
9 EN
4 Press the shutter button halfwaydown to focus.
Press
halfway
PP
F3.0F3.01/4001/400
Shutter
speed
AF target mark
Aperture
value
● The camera was unable to focus if the AF target
mark flashes red. Try focusing again.
5 To take the picture, gently pressthe shutter button all the way
down while being careful not toshake the camera.
Press halfway Press fully
Shooting still images
1 Press the n button to turnon the camera.
2 Select the shooting mode. (p. 12)
3 Hold the camera and compose theshot.
When holding the camera, take care not to cover
the flash, microphone or other important parts
with your fingers, etc.
Take care so that the flash window is not
exposed to fingerprints or dirt.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 10/78
10 EN
Using the zoom
Turning the zoom lever adjusts the shooting range.
W side T side
Image size Zoom bar
16M
Optical zoom
Other
*1
*1
Due to increased processing of the pixelcounts, the image quality will not degrade. The
magnification ratio changes depending on the
image size setting.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 11/78
11EN
Shooting screen displays
F3.0F3.01/1001/100
0.00.0
AUTOWBAUTOWB
AUTOISOAUTOISO
16M
zz
PP
0:00:340:00:3444 NORM Date
1
2 345 6 7
8 9
10
1417 18 19 16 15 1113
20
21
22
232425
12
When the shutter button is pressed halfway
down
No. Name Normal Detailed No info.
1 Shooting mode R R –
2 Flash R R –
3 Macro R R –
4 Self-timer R R R
5 Exposure
compensation R R –
6 White balance R R –
7 ISO sensitivity R R –
8 Drive R R –
9 Image size(still images)
R R –
10 Recording with sound R R –
11 Image size (movies) R R –
12 Movie recording
length R R –
13 Movie recording icon R R –
14 World time – R –
15 Image Stabilizer – R –
16 Date stamp R R –
17 Compression R R –
18 Number of storable
still pictures R R –
19 Current memory R R –
20 Battery check R R –
21 AF target mark R R R22 Grid Guide – R –
23 Aperture value R R R
24 Shutter speed R R R
25 Camera shake
warning R R R
Switching the displaysSwitching the displays
The displays change in the order of Normal → Detailed → No info. each timeF (INFO) is pressed.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 12/78
12 EN
The default settings of the function are
highlighted in .
Shooting mode Submode P (P mode) –
M (M mode) –
Q (Q mode)Recommended/Set 1/Set 2/
Set 3
( mode)
B Portrait/F Landscape/
G Night Scene/
M Night+Portrait/C Sport/
N Indoor/W Candle/R Self Portrait/S Sunset/
X Fireworks/V Cuisine/
d Documents/
q Beach & Snow/ Pet
P (P mode)
Pop Art/Pin Hole/Fish Eye/
Drawing/Soft Focus/Punk/Sparkle/Watercolor/
Reflection/Miniature
p (Panorama mode) –
● “List of settings available in each shooting mode”
(p. 57), “List of settings” (p. 58), “List of P
settings” (p. 60)
1 PressH of the arrow pad onstandby mode screen first, and
pressHI to select shootingmode.
To select the Q, and P submodes,
display submodes by usingG first. Then use
HI to select the desired submode and press
theA button.
Scene Mode OO
MENUMENU
16M
To select a submodeTo select a submodePortrait
MENUMENUMENUMENU
16M
16M
0:00:340:00:3444 NORM
Icon indicating the submode that is set
Selecting the shooting mode
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 13/78
13 EN
Learning about the shooting
modes
P ( P mode)
The camera will select the appropriateaperture value and shutter speed forthe subject. Changes can also be madeto various shooting settings, such asexposure compensation, as needed.
M ( M mode)
The camera will automatically select theoptimal shooting mode for the scene.The shooting condition is decided by
the camera and settings cannot bechanged, excepting some functions.
Q ( Q mode)
You can shoot with Beauty Fix effects.
1 Point the camera toward thesubject. Check the frameappearing around the facedetected by the camera, and thenpress the shutter button to takethe picture.
2 To save the image, select [OK] onthe review screen and press theQ button. To retouch the imageadditionally, select [Beauty Fix].
MENUBack
OK
Beauty Fix
Beauty FixBeauty Fix
1 UseFGHI to select a retouching item, and
press theQ button.
MENU
Off
Eye Color Back
2 Check the retouched effects on the review screen,
then press theQ button to start the retouch
process and save.
● Settings for Beauty Fix can be registered. ● Depending on the picture, the editing may not be
effective.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 14/78
14 EN
( mode )
You can shoot with the best modefor the subject and shooting scene.
The best shooting settings for variousscenes are pre-programmed assubmodes. Note that functions may belimited in some modes.
Refer to the descriptions displayed onthe submode selection screen, andselect the desired submode.
P ( P mode)
You can shoot with special effects.
Refer to the sample images displayedon the submode selection screen, and
select the desired submode.The best shooting settings for eacheffect are pre-programmed, so somefunction settings cannot be changed.
● Note that some effects may not be applied to
movies.
p (Panorama mode)
You can shoot and combine multipleimages to create an image with a wide
angle of view (panoramic image).1 UseFGHI to specify at which edge the next
picture is to be connected, and then press theA
button.
Direction for
combining frames
2 Press the shutter button to take the first frame.
The edge of the first frame is displayed faintly on
the screen.
3 Compose the next shot so that the edge of the
first frame displayed faintly on the screen overlapsthe subject of the second frame, and press the
shutter button.
4 Repeat step3 until the desired number of frames
are taken, and then press theA button or
button when finished.
Panorama shooting is possible for up to 10 frames.
The shot images are combined into a single
panorama image by the PC software.
● For details on installing the PC software, refer
to (p. 43). In addition, refer to the PC software
help guide for details on how to make panorama
images.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 15/78
15 EN
Viewing images
1 Press theq button.Number of frames/
Total number of images
12:30’13/02/26’13/02/26 12:30
4/304/30
Playback image
● Pictures taken using Q mode are displayed as
a group. Turn the zoom lever to the T side to play
back the image in the group.
2 UseHI to select an image.
Displays
previous image
Displays next
image
● HoldI to fast forward and holdH to reverse.
● Press theq button again to return to the shooting
screen.
To play sound recordingsTo play sound recordings
To play sound recorded with an image, select the
image and press theA button.
● PressFG to adjust volume.
Index view and close-up view
Index view enables quick selection of a desired
image. Close-up view (up to 10× magnification)
allows checking of image details.
1 Turn the zoom lever.
4/304/30 4/304/30
W T
W
T 12:30’13/02/26’13/02/26 12:3012:30’13/02/26’13/02/26 12:30
’13/02/26 12:30
Single-image view Close-up view
Index view
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 16/78
16 EN
To select an image in index viewTo select an image in index view
UseFGHI to select an image, and press theA
button to display the selected image in single-image
view.
To scroll an image in close-up viewTo scroll an image in close-up viewUseFGHI to move the viewing area.
Playing back grouped images
If the pictures are taken using Q, the images
taken are displayed as a group during playback.
Several operations are available for the grouped
images; such as expanding to view or eraseimages individually, or erasing the grouped images
collectively.
T side Expands.
• Select the image and press the
A button to display the images
individually.
• UseHI to view the previous/next frame.
A button Playback/pauses playback.
FG Adjusts the volume when playing
back images with sound.
If a group frame is erased, all images in thatgroup are erased collectively. If the group
includes images you want to keep, expand the
group and protect them individually.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 17/78
17 EN
Playback mode display
● NormalNo. Name Normal Detailed No info.
1 Battery check – R –
2 Eye-Fi transfer
data R R –3 Protect R R –
4 Adding sound R R –
5 Upload order R R –
6 Print reservation/
number of prints R R –
7 Current memory R R –
8 Frame number/total number of
imagesR R –
9 Shooting
submode – R –
10 Shutter speed – R –
11 Shooting mode – R –
12 ISO sensitivity – R –
13 Aperture value – R –14 Exposure
compensation – R –
15 White balance – R –
16 File name – R –
17 Compression – R –
18 Image size – R –
19 Recording dateand time R R –
20 Grouped image R R R
12:30’13/02/26’13/02/26 12:30
1010 4/304/30
8 7 2 3 4 6 5
1920
Still image
● Detailed
4/304/30
2.02.01/10001/1000
AUTOWBAUTOWB
100ISO100ISO1
MAGICMAGIC
1010
12:30’13/02/26’13/02/26 12:30
16M 100-0004100-0004NORM
F3.0F3.0
2.02.01/10001/1000
AUTOWBAUTOWB
100ISO100ISO1
MAGICMAGIC
16M 100-0004100-0004NORM
F3.0F3.0
1 8 7 2 3 4 1110 12 9 13
14
16
19 18
15
17
20
6 5
● No information
20
Switching the displaysSwitching the displaysThe displays change in the order of Normal → Detailed → No info. each timeF (INFO) is pressed.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 18/78
18 EN
Erasing images during playback
1 Display the image you want toerase and pressG ().
MENUErase Back
Erase
Cancel
4/304/30
2 PressFG to select [Erase], andpress theA button.
● Grouped images are erased as a group.
● Multiple images or all images can be erased at a
time (p. 34).
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 19/78
19 EN
Shooting movies
1 Press theR button to startrecording.
0:00RECREC 0:00 0:00:340:00:34
0:00:340:00:340:000:00RECRECLights up red when
recording
Recording time
Recording length (p. 64)
● The movie is shot in the set shooting mode. Note
that the shooting mode effects may not be obtainedfor some shooting modes.
● Sound is also recorded.
2 Press theR button again to stoprecording.
Playing back movies
Select a movie, and press theA button.
0:12/0:340:12 /0:34
During playbackMovie
4/304/30
OKMovie PlayMovie Play ’13/02/2612:30’13/02/2612:30
Pausing andrestarting
playback
Press theA button to pause
playback. During pause, fast
forward or reverse, press theA
button to restart playback.
Fast forward
PressI to fast forward. Press
I again to increase the fast
forward speed.
Rewind
PressH to rewind. PressH
again to increase the rewindspeed.
Adjusting the
volumeUseFG to adjust the volume.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 20/78
20 EN
Operations while playback is pausedOperations while playback is paused
During pause
0:12/0:340:12/0:34Elapsed time/
Total shooting time
Cueing
UseF to display the first frame
and pressG to display the last
frame.
Advancing and
rewinding one
frame at a time
PressI orH to advance or
rewind one frame at a time. Hold
I orH pressed for continuous
advance or rewind.
Resuming
playbackPress theA button to resume
playback.
To stop movie playbackTo stop movie playbackPress the button.
● To play back movies on the computer, the supplied
PC software is recommended. For the first use of
the supplied PC software, connect the camera to
the computer, then launch the software (p. 42).
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 21/78
21EN
Menu settings
In certain shooting modes, some functions cannot be set.
Program Auto PP
0.00.0
AUTOWBAUTOWB
AUTOISOAUTOISO
MENUMENU16M
67
321
54
8
Function menu
Setup menu (p. 25)
Function menuFunction menu
1 Flash 3 Self-timer 5 White balance 7 Drive
2 Macro 4 Exposure compensation 6 ISO sensitivity 8 Image Size
Using the function menu
1 UseH of the arrow pad to display
the function menu.
2 UseFG of the arrow pad to
select the function to be set.
3 UseHI of the arrow pad to
select the setting value, and then
press theA button to enter the
setting.
Example: Exposure compensation
Exposure Comp. ± 0.0 PP
MENUMENU
16M
AUTOWBAUTOWB
AUTOISOAUTOISO
00 11 2222 11
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 22/78
22 EN
Flash Sets the flash firing method.
_ Flash Auto The flash fires automatically in low-light or backlight conditions.
! Redeye Pre-flashes are emitted to reduce the occurrence of red eye in your photos.
# Fill In The flash fires regardless of the available light.
$ Flash Off The flash does not fire.
Macro Sets the function for shooting subjects at close distances.
` Off Macro mode is deactivated.
& MacroYou can shoot the image at a range as close as 20 cm/7.9 in. (W) to 90 cm/35.4 in.
(T).
a Super Macro This enables shooting as close as 1 cm (0.4 in.) to the subject.
Self-timer Sets the time after the shutter button is pressed until the picture is taken.
b Y Off The self-timer is deactivated.
c Y 12 secThe self-timer lamp turns on for approx. 10 seconds, then blinks for approx.
2 seconds, and then the picture is taken.
d Y 2 sec The self-timer lamp blinks for approx. 2 seconds, then the picture is taken.
Exposure
compensation
Compensates the brightness (appropriate exposure) adjusted by the camera.
to ValueSet a larger negative (–) value to adjust darker, or a larger positive (+) value to
adjust brighter.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 23/78
23 EN
White balance Sets an appropriate color scheme for the light of the shooting scene.
e WB Auto The camera automatically adjusts the white balance.
f Sunny Suitable for shooting outdoors under a clear sky.
g Cloudy Suitable for shooting outdoors under a cloudy sky.
h Incandescent Suitable for shooting under tungsten lighting.
Fluorescent Suitable for shooting under white fluorescent lighting.
One Touch 1For manually adjusting the white balance according to the light when shooting. Set a
piece of white paper or other white object so that it fills the entire screen, and press
the button to set the white balance. For the settings of one touch WB, refer
to p. 24. One Touch 2
ISO sensitivity Sets the ISO sensitivity.
l ISO Auto The camera automatically sets the sensitivity with priority on image quality.
mHigh ISO
Auto
The camera automatically sets the sensitivity with priority on minimizing blur caused
by a moving subject or by camera shake.
to Value Set a smaller value to reduce noise in the picture, or a larger value to reduce blur.
Drive Sets the sequential shooting function.
o Single One frame is shot each time the shutter button is pressed.
j SequentialThe images are taken sequentially while holding down the shutter for up to 200
frames.
c High-Speed1 The camera takes sequential shots at approximately 1.5 frames/sec.
d High-Speed2 The camera takes sequential shots at approximately 15 frames/sec.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 24/78
24 EN
Image size Sets the number of recording pixels.
4608×3456 Suitable for printing pictures over A3 (11×17 in.).
4 3264×2448 Suitable for printing pictures up to A3 (11×17 in.).
n 2560×1920 Suitable for printing pictures up to A3 (11×17 in.).
3 2048×1536 Suitable for printing pictures up to A4 size (8.5×11 in.).
2 1600×1200 Suitable for printing pictures at A5 (5×7 in.).
1 1280×960 Suitable for printing pictures at postcard size.
7 640×480 Suitable for using pictures on emails.
0 1920×1080Suitable for playing pictures on a TV (widescreen TV) and for printing on A5
(5×7 in.).
● In certain shooting modes, some functions cannot be set. Refer to “List of settings available in each shooting
mode” (p. 57)
Registering one touch white balanceRegistering one touch white balance
Select [ One Touch 1] or [ One Touch 2], face the camera toward a piece of white paper or other white
object, and press the button.
● The camera releases the shutter and the white balance is registered. When the white balance was
previously registered, the registered data is updated. ● The registered white balance data will not be cleared by turning off the power.
● Perform this procedure under the light where the pictures will be actually taken.
● When the camera settings are changed, the white balance must be registered again.
● When the white balance cannot be registered, check that the white paper fills the screen, and then
perform the procedure again.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 25/78
25 EN
Setup menuSetup menu
MENU
On
Camera Menu 1
Image Stabilizer
ResetReset
Compression
On
OnAF Illuminat.
Icon Guide
Normal
AF ModeDigital Zoom
Face/iESPOff
Back
6
2
5
34
7
1
4 Playback Menu
q
Slideshow
Edit
ErasePrint Order
R (Protect)
Upload Order
1 Camera Menu 1 5 Settings Menu 1
z
ResetCompression
AF Mode
Digital Zoom
Image Stabilizer
AF Illuminat.
Icon Guide
d
Memory Format/FormatBackup
Eye-Fi
USB Connection
q Power On
Keep z Settings
Sound Settings
2 Camera Menu 2 6 Settings Menu 2
z
Date Stamp
d
Pixel Mapping
s (Monitor)
NTSC / PAL
Power Save
l (Language)
X (Date/time)
World Time
3 Movie Menu 7 Settings Menu 3
A
Image Size
Frame Rate
IS Movie Mode
R (Movie sound recording) d
Beauty Settings
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 26/78
26 EN
Using the setup menu
Press the button during shooting or playback to display the setup menu.
The setup menu provides access to a variety of camera settings, such as shooting and playback functions,
time and date settings, and display options.
3 UseFG to select the desiredsubmenu 1 and then press theA button.
Power SavePower Save Off
MENUSettings Menu 2
Pixel Mapping
Back
World TimeWorld Time
NTSC/PAL NTSC
Bright
English
X ’13/02/26 12:30
Power SavePower Save
Pixel Mapping
MENUSettings Menu 2 Back
World TimeWorld Time
NTSC/PAL
X
On
Off
Submenu 2
4 UseFG to select the desired
submenu 2 and then press theA button.
● Once a setting is selected, the display returns
to the Submenu 1.
● There may be additional operations.
Power SavePower Save On
MENUSettings Menu 2
Pixel Mapping
Back
World TimeWorld Time
NTSC/PAL NTSC
English
X ’13/02/26 12:30
Bright
5 Press the button tocomplete the setting.
1 Press the button. ● The setup menu is displayed.
MENU
On
Camera Menu 1
Image Stabilizer
ResetReset
Compression
On
OnAF Illuminat.
Icon Guide
Normal
AF Mode
Digital Zoom
Face/iESP
Off
Back
2 PressH to select the page tabs.UseFG to select the desiredpage tab and pressI.
MENUSettings Menu 2
Pixel Mapping
Back
Power SavePower Save
World TimeWorld Time
NTSC/PAL NTSC
English
Off
X ’13/02/26 12:30
Bright
Page tab
Pixel Mapping
MENUSettings Menu 2
Power SavePower Save
World TimeWorld Time
NTSC/PAL
Back
NTSC
English
Off
X ’13/02/26 12:30
Bright
Submenu 1
Th d f lt tti f th f ti hi hli ht d S l ti th i lit f till
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 27/78
27 EN
● The default settings of the function are highlighted
in .
● For the operation method, refer to “Using the setup
menu” (p. 26).
z Camera Menu 1
Restoring the shooting functions
Restoring the shooting functions
to the default settings
to the default settingsz [Reset]
[Reset]
Submenu 2 Application
Yes
Restores the following menufunctions to the default settings.
• Shooting mode
• Flash
• Macro
• Self-timer
• Exposure compensation
• White balance
• ISO sensitivity• Drive
• Image Size (still images)
• Camera Menu 1, Camera Menu
2 and Movie Menu Functions
No The settings will not be changed.
Selecting the image quality for still
Selecting the image quality for still
images
imagesz [Compression]
[Compression]
Submenu 2 Application
Fine Shooting at high quality.
Normal Shooting at normal quality.
● “Number of storable pictures (still images)/
Recording length (movies) in the internal memory
and cards” (p. 63, 64)
Selecting the focusing area
Selecting the focusing area
z [AF Mode][AF Mode]
Submenu 2 Application
Face/iESP
The camera focuses
automatically. (If a face is
detected, it is shown by a white
frame*1; when the shutter button is
pressed halfway and the camera
focuses, the frame turns togreen*2. If no face is detected, the
camera chooses a subject in the
frame and focuses automatically.)
Spot
The camera focuses on the
subject located within the AF
target mark.
AF Tracking
The camera tracks the subject
movement automatically to focus
on it continuously.
*1 For some subjects, the frame may not appear or
may take some time to appear.*2 If the frame blinks in red, the camera cannot focus.
Try refocusing on the subject.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 28/78
Reducing the blur caused by the Using the assist lamp for shooting
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 29/78
29 EN
Reducing the blur caused by the
Reducing the blur caused by the
camera shake when shooting
camera shake when shooting z
[Image Stabilizer]
[Image Stabilizer]
Submenu 2 Application
Off
The image stabilizer is
deactivated. This is recommended
for shooting when the camera is
fixed in place on a tripod or other
stable surface.
On
Image stabilization is activated
when the shutter button is
pressed halfway.
While Exposing
Image stabilization is activated
when the shutter button is
pressed all the way down.
● While [Image Stabilizer] is active, camera may
sound during image stablization.
● Images may not be stabilized if camera shake is
too severe. ● When the shutter speed is extremely slow, such
as when taking pictures at night, [Image Stabilizer]
may not be as effective.
Using the assist lamp for shooting
Using the assist lamp for shooting
a dark subject
a dark subjectz [AF Illuminat.]
[AF Illuminat.]
Submenu 2 Application
Off The AF illuminator is not used.
On
When the shutter button is
pressed halfway down, the
AF illuminator turns on to aid
focusing.
AF illuminator
Displaying icon guides
z Camera Menu 2
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 30/78
30 EN
Displaying icon guides
Displaying icon guidesz
[Icon Guide]
[Icon Guide]
Submenu 2 Application
Off No icon guide is displayed.
On
The explanation of the selected
icon will be displayed when a
shooting mode or function menu
icon is selected (position the
cursor on the icon for a while to
display the explanation).
Icon guide
Program Auto
Functions can be
changed manually.
PP
0.00.0
AUTOWBAUTOWB
AUTOISOAUTOISO
MENUMENU
16M
z Camera Menu 2
Imprinting the date of recording
Imprinting the date of recordingz
[Date Stamp]
[Date Stamp]
Submenu 2 Application
Off Do not imprint the date.
OnStamp new photographs with the
date of recording.
● When the date and time are not set, [Date Stamp]
cannot be set. “Turning on the camera and makingthe initial settings” (p. 7)
● The date stamp can not be deleted.
● When drive settings are set to other than [o],
[Date Stamp] cannot be set.
A Movie Menu Recording sound when shooting
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 31/78
31EN
A Movie Menu
Selecting the image size for movies
Selecting the image size for movies
A [Image Size/Frame Rate][Image Size/Frame Rate]
Submenu 1 Submenu 2 Application
Image Size
720P
(1280×720)/
VGA (640×480)
Select the image
quality based on
the image size and
frame rate. Higher
frame rates provide
smoother movie
images.
Frame Rate30fps*1/
15fps*1
*1 frames per second
● “Number of storable pictures (still images)/
Recording length (movies) in the internal memory
and cards” (p. 63, 64)
Reducing the blur caused by the
Reducing the blur caused by the
camera shake when shootingcamera shake when shooting
A[IS Movie Mode]
[IS Movie Mode]
Submenu 2 Application
Off
The image stabilizer is
deactivated. This is recommended
for shooting when the camera is
fixed in place on a tripod or otherstable surface.
On The image stabilizer is activated.
● Images may not be stabilized if camera shake is
too severe.
Recording sound when shooting
Recording sound when shooting
movies
moviesA [
[
R ]
]
Submenu 2 Application
Off No sound is recorded.
On Sound is recorded.
● When set to [On], only the digital zoom can be
used during movie recording. To record the movie
with the optical zoom, set [R] (movies) to [Off].
q Playback Menu
Playing back images automatically
Playing back images automatically
q
q [Slideshow]
[Slideshow]
Submenu 2 Submenu 3 Application
BGMOff
No background music
is played.
OnBackground music is
played.
Type
Normal/
Fader/
Zoom
Selects the type of
transition effect used
between slides.
Start ― Starts the slideshow.
● During a slideshow, pressI to advance one
frame,H to go back one frame.
Changing the image sizeq [Q] 3 Press theA button after you have selected the
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 32/78
32 EN
Changing the image size
Changing the image sizeq
q [
[
Q ]
] This saves a high-resolution image as a separate
image with a smaller size for use in e-mail
attachments and other applications.
Submenu 1 Submenu 2 Submenu 3
Edit Q
1 UseHI to select an image.
2 UseFG to select an image size and press the
A button.
● The resized image is saved as a separate
image.
Cropping image
Cropping imageqq [
[ P ]
]
Submenu 1 Submenu 2
Edit P
1 UseHI to select an image, and press theA button.
2 Use the zoom lever to select the size of the
cropping frame, and useFGHI to move the
frame.
Cropping frame
MENUBack
3 A y
area to trim.
● The edited image is saved as a separate
image.
Adding sound to still imagesAdding sound to still imagesq
q [
[
R ]
]
Submenu 1 Submenu 2
Edit R
1 UseHI to select an image.
2 Aim the microphone toward the sound source.
Microphone
3 Press theA button.
● Recording starts.
● The camera adds (records) sound for approx.
4 seconds while playing back the image.
Retouching faces on still images Beauty FixBeauty Fix
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 33/78
33 EN
Retouching faces on still images
Retouching faces on still images
q
q [Beauty Fix]
[Beauty Fix]
Submenu 1 Submenu 2
Edit Beauty Fix
● Depending on the picture, the editing may not be
effective.
1 UseHI to select an image, and press the
Q button.
2 UseFG to select a retouching item, and press
theQ button.
3 To save the image, select [OK] on the reviewscreen and press theQ button. To retouch the
image additionally, select [Beauty Fix].
● The retouched image is saved as a separate
image.
MENUBack
OK
Beauty Fix
● The [Image Size] of the retouched image is limited
to [n] or lower.
y
1 Select a retouching item, and press theQ button.
MENU
Off
Eye Color Back
2 Press theQ button on the review screen.
Brightening areas that are darkBrightening areas that are darkdue to backlight or other reasons
due to backlight or other reasons
qq [Shadow Adj]
[Shadow Adj]
Submenu 1 Submenu 2
Edit Shadow Adj
1 UseHI to select an image, and press theA
button.
● The edited image is saved as a separate image.
● Depending on the picture, the editing may not be
effective.
● The retouching process may lower the image
resolution.
Retouching red eyes in ash
Retouching red eyes in fl ash Erasing images
Erasing imagesq
q [Erase]
[Erase]
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 34/78
34 EN
g y
shooting
shootingq
q [Redeye Fix]
[Redeye Fix]
Submenu 1 Submenu 2
Edit Redeye Fix
1 UseHI to select an image, and press theA
button.
● The edited image is saved as a separate image.
● Depending on the picture, the editing may not be
effective.
● The retouching process may lower the image
resolution.
Rotating images
Rotating imagesq
q [
[ y
y ]
]
Submenu 1 Submenu 2
Edit y
1 UseHI to select an image.
2 Press theA button to rotate the image.
3 If necessary, repeat Steps1 and2 to make
settings for other images, and press the
button.
● The new picture orientations will be saved even
after the power is turned off.
g g q [ ]
Submenu 2 Application
All Erase All images in the internal memory
or card will be erased.
Sel. Image Images are individually selectedand erased.
Erase Deletes the image displayed.
● When erasing pictures in the internal memory, do
not insert the card into the camera.
● Protected images cannot be erased.
To individually select and erase imagesTo individually select and erase images[Sel. Image][Sel. Image]
1 UseFG to select [Sel. Image], and press the
A button.
2 UseFGHI to select the image to be erased,
and press theA button to add a R mark to the
image.
● Turn to the T end to return to the single framedisplay.
Sel. Image
Erase/Cancel
OK
MENU
(1)
4/30
R mark
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 35/78
d Settings Menu 1 Using an Eye F i card
Using an Eye-Fi card d [Eye Fi]
[Eye-Fi]
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 36/78
36 EN
g
Erasing data completely
Erasing data completely
d [Memory Format]/
[Memory Format]/ d [Format]
[Format]
● Before formatting, check that no important data is
left in the internal memory or card.
● Cards must be formatted with this camera before
first use or after being used with other cameras or
computers.
● Be sure to remove the card before formatting the
internal memory.
Submenu 2 Application
Yes
Completely erases the image data
in the internal memory or card
(including protected images).
No Cancels formatting.
Copying images in the internalCopying images in the internalmemory to the card
memory to the card d [Backup]
[Backup]
Submenu 2 Application
YesBacks up image data in the
internal memory to the card.
No Cancels the backup.
Submenu 2 Application
All Transfers all images.
Sel. Image Transfers only selected image.
Off Disable Eye-Fi communication.
● When using an Eye-Fi card, read the Eye-Fi card
instruction manual carefully, and comply with the
instructions.
● Use the Eye-Fi card in compliance with the laws
and regulations of the country where the camera
is used. ● In locations such as on an airplane, where the Eye-
Fi communication is prohibited, remove the Eye-Fi
card from the camera, or set [Eye-Fi] to [Off].
● This camera does not support the Eye-Fi card’s
Endless mode.
Selecting a method for connecting
Selecting a method for connectingSaving the mode when the camera
Saving the mode when the camera
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 37/78
37 EN
the camera to other devices
the camera to other devices
d [USB Connection]
[USB Connection]
Submenu 2 Application
Auto
Set to select the connection
method each time the camera is
connected to another device.
Storage Connect as a card reader.
MTP
As a portable device, connect to
PC loaded with Windows Vista/
Windows 7/Windows 8.
PrintSelect when connecting to aPictBridge-compatible printer.
● Select [Storage] to use the supplied software.
● Refer to “Connecting with a computer” (p. 42) for the
connection method with a computer.
Turning on the camera w ith theTurning on the camera with theqq button
button d [[ qq Power On]
Power On]
Submenu 2 Application
No
The camera is not turned on. To
turn on the camera, press the
n button.
YesPress and hold theq button
to turn the camera on in the
playback mode.
is turned off
is turned off d [Keep
[Keepz Settings]
Settings]
Submenu 2 Application
Yes
The shooting mode is saved
when the camera is turned off andis reactivated the next time the
camera is turned on.
On
The shooting mode is set to P
mode when the camera is turned
on.
Selecting the camera sound andSelecting the camera sound andits volume
its volume d [Sound Settings]
[Sound Settings]
Submenu 2 Submenu 3 Application
Sound Type 1/2/3
Selects the camera
sounds (operation
sounds and shutter
sound).
Volume 0/1/2/3/4/5
Selects the operation
volume of camera
buttons.
q Volume 0/1/2/3/4/5Selects the image
playback volume.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 38/78
Playing back images on a TV
Playing back images on a TV d [NTSC/PAL]
[NTSC/PAL]
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 39/78
39 EN
The TV video signal system varies depending on the countries and regions. Before viewing camera
images on your TV, select the video output according to your TV’s video signal type.
Submenu 2 Submenu 3 Application
NTSC/PAL
NTSCConnecting the camera to a TV in North America, Taiwan, Korea,
Japan, and so on.
PALConnecting the camera to a TV in European countries, China, and
so on.
The factory default settings differ according to the region where the camera is sold.
To play back camera images on a TVTo play back camera images on a TV ● Connection via AV cable
1 Use the camera to select the same video signal system as the one of connected TV ([NTSC]/[PAL]).
2 Connect the TV and camera.
3 Turn on the TV, and change “INPUT” to “VIDEO (an input jack connected to the camera)”.
4 Turn on the camera, and useFGHI to select the image for playback.
Connect to the TV videoinput jack (yellow) and
audio input jack (white).
Multi-connector
AV cable (sold separately: CB-AVC5)
● For details on changing the input source of the TV, refer to the TV’s instruction manual.
● Depending on the TV’s settings, the displayed images and information may become cropped.
Saving battery power between
Saving battery power between
h t d [P S ]
Choosing home and alternate time
Choosing home and alternate time
d [W ld Ti ]
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 40/78
40 EN
shots
shots d [Power Save]
[Power Save]
Submenu 2 Application
Off Cancels [Power Save].
On
When the camera is not being
used for approx. 10 seconds, the
monitor automatically turns off to
save battery power.
To resume standby modeTo resume standby modePress any button.
Changing the display language
Changing the display language
d [[ l ]
]
Submenu 2 Application
Languages
The language for the menus and
error messages displayed on the
monitor is selected.
Setting the date and time
Setting the date and time d [[ XX ] ] 1 Press the Arrow pad toFG to select the year for
[Y].
2 Press the Arrow pad to I to save the setting for
[Y].3 As in Steps1 and2, press the Arrow pad to
FGHI to set [M] (month), [D] (day), [Time]
(hours and minutes), and [Y/M/D] (date order),
and then press theA button.
● For precise time setting, press theA button as the
time signal strikes 00 seconds.
zones
zones d [World Time]
[World Time]
● You will not be able to select a time zone using
[World Time] if the camera clock has not first been
set using [X].
Submenu 2 Submenu 3 Application
Home/
Alternate
x
The time in the home
time zone (the time
zone selected for x
in submenu 2).
z
The time in the travel
destination time
zone (the time zone
selected forz in
submenu 2).
x*1 —Select the home time
zone (x).
z*1, 2 —
Select the travel
destination time zone
(z).*1 In areas where daylight saving time is in effect, use
FG to turn daylight saving time ([Summer]) on.*2 When you select a time zone, the camera
automatically calculates the time difference
between the selected zone and the home
time zone (x) to display the time in the travel
destination time zone (z).
d Settings Menu 3
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 41/78
41EN
Registering the settings for Beauty
Registering the settings for Beauty
Fix
Fix d [Beauty Settings]
[Beauty Settings]
● Depending on the picture, the editing may not beeffective.
1 UseFG to select a retouching setting, and
press theQ button.
2 Press the shutter button to take a portrait picture.
Take a portrait picture.
● The image is not saved.
3 Select a retouching item, and press theQ button.
MENU
Off
Eye Color Back
4 Press theQ button on the review screen to save
the image.
● Registration is complete.
Connecting with a computer
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 42/78
42 EN
When [USB Connection] is set to [Auto], connect the
camera and the computer, select [Storage] or [MTP]
at the screen for selecting the connection method,
and then press theA button.
System requirementsSystem requirementsWindows : Windows XP Home Edition/
Professional (SP1 or later)/
Windows Vista/Windows 7/
Windows 8
Macintosh : Mac OS X v10.3 or later
● Even if a computer has USB ports, proper
operation is not guaranteed in the following cases:
● Computers with USB ports installed using an
expansion card, etc.
● Computers without a factory-installed OS and
home-built computers
● When the computer does not support SDXC
cards, a message may appear urging to format
the internal memory or card. (Formatting will
completely erase all images, so do not format.)
Set [USB Connection] in the setup menu of the
camera beforehand. (p. 37)
Connecting the cameraConnecting the camera
USB cable
(supplied)
Multi-connector
Installing the PC software and
registering user2 Register your Olympus product.
● Click the “Registration” button and follow the
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 43/78
43 EN
registering user
WindowsWindows
1 Insert the supplied CD in a CD-ROM drive.
Windows XP
● A “Setup” dialog will be displayed.
Windows Vista/Windows 7/Windows 8
● An Autorun dialog will be displayed. Click
“OLYMPUS Setup” to display the “Setup” dialog.
● If the “Setup” dialog is not displayed, select “My
Computer” (Windows XP) or “Computer” (Windows
Vista/Windows 7) from the start menu. Double-click
the CD-ROM (OLYMPUS Setup) icon to open the
“OLYMPUS Setup” window and then double-click“Launcher.exe”.
If a “User Account Control” dialog is displayed,
click “Yes” or “Continue”.
● Click the Registration button and follow the
on-screen instructions.
● To register the camera must be connected to
the computer. “Connecting the camera” (p. 42)
● If nothing is displayed on the camera screeneven after connecting the camera to the
computer, the battery may be exhausted.
Charge the battery and then connect the
camera again.
3 Install OLYMPUS Viewer 3. ● Check the system requirements before
beginning installation.
● Click the “OLYMPUS Viewer 3” button and
follow the on-screen instructions to install the
software.
OLYMPUS Viewer 3
Operating
System
Windows XP (Service Pack 2 or later) /
Windows Vista / Windows 7 /
Windows 8
Processor
Pentium 4 1.3 GHz or better (Core 2
Duo 2.13 GHz or better required for
movies)
RAM1 GB or more
(2 GB or more recommended)
Free Hard
Drive Space3 GB or more
Monitor
Settings
1024 × 768 pixels or more
Minimum 65,536 colors
(16,770,000 colors recommended)
● See online help for information on using the
software.
4 Install the camera manual.● Click the “Camera Instruction Manual” button
OLYMPUS Viewer 3
OperatingM OS X 10 5 10 8
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 44/78
44 EN
● Click the Camera Instruction Manual button
and follow the on-screen instructions.
MacintoshMacintosh
1 Insert the supplied CD in a CD-ROM drive.
● Double-click the CD (OLYMPUS Setup) icon
on the desktop.
● Double-click the “Setup” icon to display the
“Setup” dialog.
2 Install OLYMPUS Viewer 3. ● Check the system requirements before
beginning installation.
● Click the “OLYMPUS Viewer 3” button and
follow the on-screen instructions to install the
software.
● You can register via “Registration” inOLYMPUS Viewer 3 “Help”.
Operating
SystemMac OS X v10.5–v10.8
Processor
Intel Core Solo/Duo 1.5 GHz or better
(Core 2 Duo 2 GHz or better required
for movies)
RAM1 GB or more (2 GB or more
recommended)
Free Hard
Drive Space3 GB or more
Monitor
Settings
1024 × 768 pixels or more
Minimum 32,000 colors
(16,770,000 colors recommended)
● Other languages can be selected from the
language combo box. For information on using the
software, see online help.
3 Copy the camera manual. ● Click the “Camera Instruction Manual” button to
open the folder containing the camera manuals.
Copy the manual for your language to the
computer .
Direct printing (PictBridge)
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 45/78
45 EN
By connecting the camera to a PictBridge-compatible
printer, you can print images directly without using a
computer.
Tofi
nd out if your printer supports PictBridge, refer tothe printer’s instruction manual.
● The printing modes, paper sizes, and other
parameters that can be set with the camera vary
depending on the printer that is used. For details,
refer to the printer’s instruction manual.
● For details on the available paper types, loading
paper, and installing ink cassettes, refer to the
printer’s instruction manual. ● In the setup menu, set [USB Connection] to [Print].
[USB Connection] (p. 37)
Printing images at the printer’s
standard settings [Easy Print]
1 Display the image to be printed onthe monitor.
● “Viewing images” (p. 15)
2 Turn on the printer, and thenconnect the printer and camera.
USB cable
(supplied)
Multi-connector
I (right)
3 PressI to start printing.
4 To print another image, useHI to select an image, and press theA button.
To exit printingTo exit printing
After a selected image is displayed on the screen,
disconnect the USB cable from the camera and
printer.
Changing the printer’s settings
for printing [Custom Print]5 UseFG to select [Size]
(Submenu 3), and pressI.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 46/78
46 EN
for printing [Custom Print]
1 Display the image to be printed on
the monitor. ● “Viewing images” (p. 15)
2 Turn on the printer, and thenconnect the printer and camera.
3 Press theA button.
4 UseFG to select the print mode,and press theA button.
Submenu 2 Application
PrintThis prints the image selected
in Step 8.
All PrintThis prints all images stored in the
internal memory or card.
Multi PrintThis prints one image in a multiple
layout format.
All Index
This prints an index of all images
stored in the internal memory
or card.
Print Order *1This prints images based on the
print reservation data on the card.
*1 [Print Order] is available only when print
reservations have been made. “Print Reservations”
(p. 48)
(Submenu 3), and pressI. ● If the [Printpaper] screen is not displayed, the
[Size], [Borderless], and [Pics/Sheet] are set to the
printer’s standard.
MENUPrintpaper
Size Borderless
Back
Standard Standard
6 UseFG to select the[Borderless] or [Pics/Sheet]settings, and press theA button.
Submenu 4 Application
Off/On*1
The image is printed with a border
around it ([Off]).The image is printed to fill the
entire paper ([On]).
(The number
of images per
sheet varies
depending on
the printer.)
The number of images per sheet
([Pics/Sheet]) is selectable only
when [Multi Print] is selected in
Step 4.
*1 The available settings for [Borderless] vary
depending on the printer.
If [Standard] is selected in Steps 5 and 6, the
image is printed at the printer’s standard settings.
7 UseHI to select an image.
8 P F t k i t
To crop an image [To crop an image [ P]]1 Use the zoom lever to select the size of the
cropping frame useFGHI to move the frame
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 47/78
47 EN
8 PressF to make a printreservation for the current image.PressG to make the detailed
printer settings for the currentimage.
To make the detailed printer settingsTo make the detailed printer settings
1 UseFGHI to select the setting, and press the
A button.
Submenu 5 Submenu 6 Application
<X 0 to 10This selects the number
of prints.
DateWith/
Without
Selecting [With] prints
the images with the date.
Selecting [Without] prints
the images without the
date.
File NameWith/
Without
Selecting [With] printsthe file name on the
image.
Selecting [Without] does
not print any file name on
the image.
P
(Proceeds
to the
settingscreen.)
This selects a portion of
the image for printing.
cropping frame, useFGHI to move the frame,
and then press theA button.
Cropping frame
MENUBack
2 UseFG to select [OK], and press theA button.
9 If necessary, repeat Steps 7 and 8to select the image to be printed,make the detailed settings, andset [Single Print].
10 Press theA button.
Cancel
MENUPrint Back
11 UseFG to select [Print], andpress theA button.
Print Reservations
In print reservations the number of prints and date
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 48/78
48 EN
p A ● Printing starts.
● When [Option Set] is selected in [All Print]
mode, [Print Info] screen is displayed.
● When printing is finished, the [Print Mode
Select] screen is displayed.
Multi Print
Print Order
All Index
All Print
PrintPrint
MENUPrint Mode Select Back
To cancel printingTo cancel printing
1 Press the button while [Do Not Remove
USB Cable] is displayed.
2 Select [Cancel] usingFG and then press theA
button.
12 Press the button.
13 When the message [Remove USBCable] is displayed, disconnectthe USB cable from the cameraand printer.
In print reservations, the number of prints and date
imprint option are saved in the image on the card.
This enables easy printing at a printer or print shop
supporting DPOF by using only the print reservations
on the card without a computer or a camera.
● Print reservations can be set only for the images
stored on the card.
● DPOF reservations set by another DPOF device
cannot be changed by this camera. Make changes
using the original device. Making new DPOF
reservations with this camera will erase the
reservations made by the other device.
● DPOF print reservations can be made for up to 999
images per card.
Single-frame print reservations
[ < ]
1 Display the setup menu. ● “Using the setup menu” (p. 26)
2 From the playback menuq,select [Print Order] and thenpress theA button.
3 UseFG to select [<], and presstheA button.
Reserving one print each of all
images on the card [ U ]
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 49/78
49 EN
0
4/304/30
Print Order Print OK
NORM
100-0004
‘13/02/26 12:30
NORM16M
100-0004
‘13/02/26 12:30
4 UseHI to select the image forprint reservation. UseFG toselect the quantity. Press theA button.
5 UseFG to select the [X] (dateprint) screen option, and presstheA button.
Submenu 2 ApplicationNo This prints the image only.
DateThis prints the image with the
shooting date.
TimeThis prints the image with the
shooting time.
6 UseFG to select [Set], andpress theA button.
1 Follow Steps 1 and 2 in [<] (p. 48).
2 UseFG to select [U], andpress theA button.
3 Follow Steps 5 and 6 in [<].
Resetting all print reservation
data
1 Follow Steps 1 and 2 in [<] (p. 48).
2 Select either [<] or [U], andpress theA button.
3 UseFG to select [Reset], andpress theA button.
Resetting the print reservation
data for selected images
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 50/78
50 EN
1 Follow Steps 1 and 2 in [<] (p. 48).
2 UseFG to select [<], and presstheA button.
3 UseFG to select [Keep] andpress theA button.
4 UseHI to select the image with
the print reservation you want tocancel. UseFG to set the printquantity to “0”.
5 If necessary, repeat Step 4, andthen press theA button whenfinished.
6 UseFG to select the [X] (dateprint) screen option, and presstheA button.
● The settings are applied to the remaining
images with the print reservation data.
7 UseFG to select [Set], andpress theA button.
Usage Tips
If the camera does not work as intended, or if an Shutter button
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 51/78
51EN
,
error message is displayed on the screen, and you
are unsure of what to do, refer to the information
below to fix the problem(s).
Troubleshooting
BatteryBattery
“The camera does not work even when batteries
are installed”.
● Insert recharged batteries in the correct
direction.
“Inserting and removing the battery and card
(commercially available)” (p. 4), “Charging the
battery” (p. 5)
● Battery performance may have been reduced
temporarily due to low temperature. Take the
batteries out of the camera, and warm them by
putting them in your pocket for a while.
Card/Internal memoryCard/Internal memory “An error message is displayed”.
“Error message” (p. 52)
Shutter buttonShutter button “No picture is taken when the shutter button is
pressed”.
●
Cancel sleep mode.To save battery power, the camera
automatically goes into sleep mode and the
monitor turns off if there is no operation for
3 minutes when the camera is turned on. No
picture is taken even if the shutter button is
fully pressed in this mode. Operate the zoom
lever or other buttons to restore the camera
from sleep mode before taking a picture. If
the camera is left for another 12 minutes, it
automatically turns off. Press the n
button to turn the camera on.
● Press theq button to switch to the shooting
mode.
● Wait until#(flash charge) stops blinking
before taking pictures.
MonitorMonitor “Dif ficult to see”.
● Condensation may have occurred. Turn off
the power, and wait for the camera body
to become acclimated to the surrounding
temperature and dry out before taking pictures.
“Vertical lines appear on the monitor”.
● This condition may occur when the camera is
pointed at an extremely bright subject under a
clear sky and so on.
The lines may appear on the recorded picture
or movie with sequential shots.
“The light is caught in the picture”.
● Shooting with flash in dark situations results in
an image with many flash reflections on dust
in the air.
Date and time functionDate and time function “Date and time settings return to the default
setting”.
Error message
● When one of the messages below is displayed on
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 52/78
52 EN
● If the batteries are removed and left out of the
camera for about 1 days*1, the date and time
settings return to the default setting, and must
be reset.*1 The time until the date and time settings
return to the default setting varies depending
on how long the batteries have been loaded.
“Turning on the camera and making the initial
settings” (p. 7)
MiscellaneousMiscellaneous
“The camera makes a noise when takingpictures”.
● The camera may activate the lens and make a
noise even if no operation is performed. This
is because the camera automatically performs
actions of auto focus as far as it is ready to
shoot.
the monitor, check the corrective action.
Error message Corrective action
Card Error
Card problem
Insert a new card.
Write Protect
Card problem
The card write-protect switch is
set to the “LOCK” side. Release
the switch.
Memory Full
Internal memory problem• Insert a card.
• Erase unwanted images.*1
Card Full
Card problem
• Replace the card.
• Erase unwanted images.*1
Card Setup
Format
Power Off
Card problem
UseFG to select [Format],and press theA button. Next,
useFG to select [Yes], and
press theA button.*2
Memory Setup
Memory Format
Power Off Power Off
Internal memory problem
UseFG to select [Memory
Format], and press the
A button. Next, useFG to
select [Yes], and press theA button.*2
*1 Before erasing important images, download them
to a computer.*2 All data will be erased.
Error message Corrective action
Internal memory/Card
problem
Error message Corrective action
Printer problem
Turn off the camera and printer,
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 53/78
53 EN
No Picture
problem
Take pictures before viewing
them.
Picture Error
Problem with selected imageUse photo retouch software,
etc. to view the image on a
computer. If the image still
cannot be viewed, the image file
is corrupted.
The ImageCannot Be
Edited
Problem with selected image
Use photo retouch software, etc.to edit the image on a computer.
Battery Empty
Battery problem
Charge the battery.
No Connection
Connection problem
Connect the camera andcomputer or printer correctly.
No Paper
Printer problem
Load paper into the printer.
No Ink
Printer problem
Refill the ink in the printer.
Jammed
Printer problem
Remove the jammed paper.
Settings
Changed*3
Printer problem
Return to the status where the
printer can be used.
Print Error
Turn off the camera and printer,
check the printer for any
problems, and then turn the
power on again.
Cannot Print*4
Problem with selected image
Use a computer to print.
*3 This is displayed, for instance, when the printer’s
paper tray has been removed. Do not operate
the printer while making the print settings on the
camera.
*4 This camera may be unable to print images takenby other cameras.
Shooting tips
When you are unsure of how to take a picture that
i i f h i f i b l
When extremely bright objects
appear in the center of the
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 54/78
54 EN
you envision, refer to the information below.
Focusing
“Focusing on the subject”
● Taking a picture of a subject not in the
center of the monitor
After focusing on an object at the same
distance as the subject, compose the shot, and
take the picture.
Pressing the shutter button halfway (p. 9) ● Set [AF Mode] (p. 27) to [Face/iESP]
● Taking a picture in [AF Tracking] mode (p. 27)
The camera tracks the subject movement
automatically to focus on it continuously.
● Taking a picture of a shadowy subject
Using the AF illuminator makes focusing
easier. [AF Illuminat.] (p. 29) ● Taking a picture of subjects where
autofocus is dif ficult
In the following cases, after focusing on an
object (by pressing the shutter button halfway
down) with high contrast at the same distance
as the subject, compose the shot, and take
the picture.
Subjects with low contrast
monitor
Object with no vertical lines*1
*1 It is also effective to compose the shot by holding
the camera vertically to focus, and then returning
to the horizontal position to take the picture.
When objects are at different
distances
Fast-moving object
The subject is not in the
center of the frame
Camera shake
“Taking pictures without camera shake”
● Taking pictures of a white beach or snow
scene
Select [q Beach & Snow] in the scene mode
(p 12)
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 55/78
55 EN
Taking pictures without camera shake
● Taking pictures using [Image Stabilizer]
(p. 29)
The image pickup device*1 shifts to correct for
camera shake even if the ISO sensitivity is not
increased. This function is also effective when
taking pictures at a high zoom magnifi cation.*1 A device that takes light received through the
lens and converts it into electric signals.
● Shooting movies using [IS Movie Mode]
(p. 31)
● Select [C Sport] in the scene mode (p. 12)
The [C Sport] mode uses a fast shutter speed
and can reduce the blur incurred by a moving
subject.
● Taking pictures at a high ISO sensitivity
If a high ISO sensitivity is selected, pictures
can be taken at a high shutter speed even at
locations where aflash cannot be used.
“ISO sensitivity” (p. 23)
Exposure (brightness)
“Taking pictures with the right brightness”
● Taking pictures using [Face/iESP] (p. 27)
Appropriate exposure is obtained for a faceagainst backlight, and the face is brightened.
● Taking pictures using [Fill In] (p. 22) flash
A subject against backlight is brightened.
(p. 12).
● Taking pictures using exposure
compensation (p. 22)
Adjust the brightness while viewing the screen
for taking the picture. Normally, taking pictures
of white subjects (such as snow) results in
images that are darker than the actual subject.
Use the exposure compensation to adjust in
the positive (+) direction to express whites as
they appear. When taking pictures of black
subjects, on the other hand, it is effective to
adjust in the negative (-) direction.
Color hue
“Taking pictures with colors at the same shade as
they appear”
● Taking pictures by selecting white balance
(p. 23)Best results in most environments can
normally be obtained with the [WB Auto]
setting, but for some subjects, you should try
experimenting with different settings. (This
is especially true for sunshade under a clear
sky, mixed natural and artificial light settings,
and so on.)
Image quality
“Taking sharper pictures”
Playback/Editing tips
Pl b k
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 56/78
56 EN
Taking sharper pictures
● Taking pictures with the optical zoom
Avoid using digital zoom (p. 28) to take pictures.
● Taking pictures at a low ISO sensitivity
If the picture is taken with a high ISO
sensitivity, noise (small colored spots and
color unevenness that were not in the original
image) can occur, and the image can appear
grainy.
“ISO sensitivity” (p. 23)
Batteries
“Making batteries last longer”
● Set [Power Save] (p. 40) to [On]
Playback
“Playing images in the internal memory and card” ● Remove the card and display the images in
internal memory
“Inserting and removing the battery and card
(commercially available)” (p. 4)
Editing
“Erasing the sound recorded to a still image”
● Record over the sound with silence when
playing back the image
“Adding sound to still imagesq [R]”(p. 32)
List of settings available in each shooting mode
For details on, refer to “List of settings” (p. 58).
For details on shaded areas refer to “List of P settings” (p 60)
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 57/78
57 EN
For details on shaded areas, refer to “List of P settings” (p. 60).
P M Q P pZoom R R R R R
Flash R *1 *1 R –
Macro R – R R R
Self-timer R R R R R
Exposure
compensation R – – R
White balance R – – R
ISO sensitivity R – – – –Drive R – – – –
Image Size R R *1 R
Compression R R R R R
AF Mode R – – – *1
Digital Zoom R – R – –
Image Stabilizer R R R R R
AF Illuminat. R R R R RIcon Guide R R R R R
Date Stamp R R R R –
*1 Some functions cannot be set.
List of settings
B F G M C N W R S
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 58/78
58 EN
Zoom R R R R R R R – R
Flash *1 – – *1 *1 *1 – *1 –
Macro – – – – – – – – –Self-timer R R R R R R R R R
Exposure
compensation – – – – – – – – –
White balance – – – – – – – – –
ISO sensitivity – – – – – – – – –
Drive – – – – – – – – –
Image Size R R R R R R R R RCompression R R R R R R R R R
AF Mode R R R R R R R – R
Digital Zoom R R R R R R – – R
Image Stabilizer R R R R R R R R R
AF Illuminat. R R R R R R R R R
Icon Guide R R R R R R R R R
Date Stamp R R R R R R R R R
*1 Some functions cannot be set.
X V d q Zoom R R R R R
Flash – *1 – *1 –
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 59/78
59 EN
Macro – – – – –
Self-timer R R R R R
Exposurecompensation
– – – – –
White balance – – – – –
ISO sensitivity – – – – –
Drive – – – – –
Image Size R R R R R
Compression R R R R R
AF Mode – R R R –Digital Zoom R R R R R
Image Stabilizer R R R R R
AF Illuminat. R R R R R
Icon Guide R R R R R
Date Stamp R R R R R
*1 Some functions cannot be set.
List ofP settings
Pop Art Pin Hole Fish Eye Drawing Soft Focus
Exposure
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 60/78
60 EN
Exposure
compensation R R – – R
White balance R R – – RImage Size R R R *1 R
Punk Sparkle Watercolor Reflection Miniature
Exposure
compensation R R R R R
White balance – R R R R
Image Size R *1 *1 R R
*1 Some functions cannot be set.
Appendix
Camera care Using a separately sold USB-AC
adapter
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 61/78
61EN
Exterior
• Wipe gently with a soft cloth. If the camera is verydirty, soak the cloth in mild soapy water and wring
well. Wipe the camera with the damp cloth and
then dry it with a dry cloth. If you have used the
camera at the beach, use a cloth soaked in clean
water and wrung well.
Monitor
• Wipe gently with a soft cloth.
Lens
• Blow dust off the lens with a commercial blower,
then wipe gently with a lens cleaner.
Do not use strong solvents such as benzene or
alcohol, or chemically treated cloth.
Mold may form on the lens surface if the lens is
left dirty.
Battery/USB-AC adapter
• Wipe gently with a soft, dry cloth.
Storage
• When storing the camera for extended periods,
remove the battery, USB-AC adapter and card, and
keep in a cool, dry place that is well ventilated. • Periodically insert the battery and test the camera
functions.
Avoid leaving the camera in places where
chemical products are handled since this may
result in corrosion.
adapter
The USB-AC adapter F-3AC (sold separately) canbe used with this camera. Do not use any USB-AC
adapter other than the dedicated one. When using
F-3AC, be sure to use the USB cable included with
this camera.
Do not use any other USB-AC adapter with this
camera.
Shooting is not available when using the F-3AC.
Using a separately sold
charger
A charger (UC-50: sold separately) can be used to
charge the battery.
Using your charger and USB-ACadapter abroad
• The charger and USB-AC adapter can be used in
most home electrical sources within the range of
100 V to 240 V AC (50/60Hz) around the world.
However, depending on the country or area you
are in, the AC wall outlet may be shaped differently
and the charger and USB-AC adapter may requirea plug adapter to match the wall outlet. For details,
ask at your local electrical shop or travel agent.
• Do not use travel voltage converters as they could
damage your charger and USB-AC adapter.
Using the card
Cards compatible with this cameraCards compatible with this cameraSD/SDHC/SDXC/Eye-Fi card (commercially
FormatFormatCards must be formatted with this camera before
first use or after being used with other cameras or
computers.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 62/78
62 EN
SD/SDHC/SDXC/Eye Fi card (commercially
available) (for compatibility card details, visit the
Olympus website.)
● This camera can be used without a card by storing
images in its internal memory.
Eye-Fi card
● The Eye-Fi card may become hot during use.
● When using an Eye-Fi card, the battery may run
out faster.
● When using an Eye-Fi card, the camera may
function more slowly.
SD/SDHC/SDXC card write-protect switchSD/SDHC/SDXC card write-protect switchThe SD/SDHC/SDXC card body has a write-protect
switch.
If you set the switch to the “LOCK” side, you will not
be able to write to the card, delete data or format.
Return the switch to enable writing.
LOCK
Checking the image saving locationChecking the image saving location
The memory indicator shows whether the internalmemory or card is being used during shooting and
playback.
Current memory indicator
v: Internal memory is being used
w: Card is being used
Even if [Memory Format]/[Format], [Erase],
[Sel. Image], or [All Erase] is performed, the
data in the card is not completely erased. When
disposing of the card, damage the card to
prevent the disclosure of personal data.
● Switching between a card and internal memory is
not available.
When using the internal memory, remove the card
first.
Readout/recording process of the cardReadout/recording process of the cardDuring shooting, the current memory indicator lights
up in red while the camera is writing data. Never
open the battery/card cover or unplug the USB cable.
This can not only damage the image data but also
render the internal memory or card unusable.
Number of storable pictures still images)/Recording length movies) in the internalNumber of storable pictures (still images)/Recording length (movies) in the internal
memory and cardsmemory and cards
The figures for the number of storable still pictures and recording length are approximate. The actual
capacity varies with shooting conditions and the card used.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 63/78
63 EN
p y g
Still picturesStill pictures
Image Size CompressionNumber of storable pictures
Internal memory SD/SDHC/SDXC card (4GB)
4608×3456L 3 430
M 7 860
4 3264×2448L 7 860
M 15 1,700
n 2560×1920L
12 1,390M 24 2,690
3 2048×1536L 20 2,210
M 39 4,430
2 1600×1200L 32 3,640
M 65 7,290
1 1280×960L 50 5,640
M 101 11,280
7 640×480L 202 20,670
M 371 41,340
0 1920×1080L 5 3,350
M 10 6,530
MoviesMovies
Image Size Frame Rate
Continuous recording length
Internal memory SD/SDHC/SDXC card (4 GB)
With sound Without sound With sound Without sound
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 64/78
64 EN
1280×72030fps 8 sec. 9 sec. 16 min. 17 min.
15fps 17 sec. 18 sec. 31 min. 34 min.
8 640×48030fps 18 sec. 18 sec. 33 min. 35 min.
15fps 34 sec. 37 sec. 64 min. 70 min.
● The maximum file size of a single movie is 2 GB, regardless of the capacity of the card.
Increasing the number of pictures that can be takenIncreasing the number of pictures that can be taken
Either erase unwanted images, or connect the camera to a computer or other device to save the images, and
then erase the images in the internal memory or card.[Erase] (p. 18, 34), [Sel. Image] (p. 34), [All Erase] (p. 35), [Memory Format]/[Format] (p. 36)
TrademarksTrademarks
• Microsoft and Windows are registered trademarks
of Microsoft Corporation.
• Macintosh is a trademark of Apple Inc.
S C f S C C
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 65/78
65 EN
• SDXC Logo is a trademark of SD-3C, LLC.
• Eye-Fi is a registered trademark of Eye-Fi, Inc.
• Powered by ARCSOFT.
• All other company and product names are
registered trademarks and/or trademarks of their
respective owners.
The software in this camera may include third party
software. Any third party software is subject to the
terms and conditions, imposed by the owners orlicensors of that software, under which software is
provided to you.
Those terms and other third party software notices,
if any, may be found in the software notice PDF file
stored within the supplied CD-ROM or at
http://www.olympus.co.jp/en/support/imsg/
digicamera/download/notice/notice.cfm
• The standards for camera file systems referred to
in this manual are the “Design rule for Camera File
system/DCF” standards stipulated by the Japan
Electronics and Information Technology Industries
Association (JEITA).
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 66/78
Operating
environment
Temperature : 0 °C to 40 °C (32 °F to 104 °F) (operation)/
-20 °C to 60 °C (-4 °F to 140 °F) (storage)
H idit 30 % t 90 % ( ti )/10 % t 90 % ( t )
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 67/78
67 EN
Humidity : 30 % to 90 % (operation)/10 % to 90 % (storage)
Power supply : One Olympus lithium ion battery (LI-50B)Dimensions : 104.3 mm (W) × 60.2 mm (H) × 28.3 mm (D)
(4.1 × 2.4 × 1.1 in.) (excluding protrusions)
Weight : 170 g (6.0 oz) (including battery and card)
Lithium ion battery LI-50B)Lithium ion battery (LI-50B)
Product type : Lithium ion rechargeable battery
Model No. : LI-50BA/LI-50BB
Standard voltage : DC 3.7 V
Standard capacity : 925 mAh
Battery life : Approx. 300 full charges (varies on usage)
Operating
environment
Temperature : 0 °C to 40 °C (32 °F to 104 °F) (charging)
USB-AC adapter F-2AC)USB-AC adapter (F-2AC)
Model No. : F-2AC-2B/F-2AC-1C/F-2AC-3C/F-2AC-4C/F-2AC-5C/F-2AC-1D/
F-2AC-3D/F-2AC-4D/F-2AC-5D/F-2AC-6D
Power requirements : AC 100 to 240 V (50/60 Hz)
Output : F-2AC-2B: DC 5 V, 500 mA
F-2AC-1C/F-2AC-3C/F-2AC-4C/F-2AC-5C/F-2AC-1D/F-2AC-3D/F-2AC-4D/F-2AC-5D/F-2AC-6D: DC5 V, 550 mA
Operating
environment
Temperature : 0 °C to 40 °C (32 °F to 104 °F) (operation)/
-20 °C to 60 °C (-4 °F to 140 °F) (storage)
Design and specifications subject to change without notice.
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC
General PrecautionsGeneral Precautions
Read All Instructions — Before you use the product,read all operating instructions Save all manuals and
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 68/78
68 EN
SHOCK
DO NOT OPENCAUTION: TO REDUCE THE RISK OF
ELECTRICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED OLYMPUS
SERVICE PERSONNEL.
An exclamation mark enclosed ina triangle alerts you to important
operating and maintenance
instructions in the documentation
provided with the product.
DANGER If the product is used without
observing the information given
under this symbol, serious injury
or death may result.
WARNING If the product is used without
observing the information given
under this symbol, injury or death
may result.
CAUTION If the product is used without
observing the information
given under this symbol, minor
personal injury, damage to the
equipment, or loss of valuable
data may result.
WARNING!
TO AVOID THE RISK OF FIRE OR ELECTRICAL
SHOCK, NEVER DISASSEMBLE, EXPOSE THIS
PRODUCT TO WATER OR OPERATE IN A HIGH
HUMIDITY ENVIRONMENT.
read all operating instructions. Save all manuals anddocumentation for future reference.
Cleaning — Always unplug this product from the walloutlet before cleaning. Use only a damp cloth forcleaning. Never use any type of l iquid or aerosolcleaner, or any type of organic solvent to clean thisproduct.
Attachments — For your safety, and to avoid damagingthe product, use only accessories recommended byOlympus.
Water and Moisture — For precautions on productswith weatherproof designs, read the weatherproofing
sections.Location — To avoid damage to the product, mount the
product securely on a stable tripod, stand, or bracket.Power Source — Connect this product only to the power
source described on the product label.Lightning — If a lightning storm occurs while using
a USB-AC adapter, remove it from the wall outletimmediately.
Foreign Objects — To avoid personal injury, never inserta metal object into the product.
Heat — Never use or store this product near any heatsource such as a radiator, heat register, stove, or anytype of equipment or appliance that generates heat,including stereo amplifiers.
Handling the CameraHandling the Camera
WARNING • Do not use the camera near flammable or explosive
gases. • Do not use the flash and LED (including AFilluminator) on people (infants, small children, etc.)at close range. • You must be at least 1 m (3 ft.) away from the faces ofyour subjects. Firing the flash too close to the subject’seyes could cause a momentary loss of vision.
• Keep young children, infants, and animals such aspets away from the camera. • Always use and store the camera out of the reach ofyoung children and infants to prevent the followingdangerous situations which could cause serious injury: • Becoming entangled in the camera strap, causingstrangulation
• Handle the camera with care to avoid getting a low-temperature burn. • When the camera contains metal parts, overheatingcan result in a low-temperature burn. Pay attention tothe following: • When used for a long period, the camera will get hot.If you hold on to the camera in this state a low
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 69/78
69 EN
strangulation. • Accidentally swallowing the battery, cards or other
small parts. • Accidentally firing the flash into their own eyes or thoseof another child. • Accidentally being injured by the moving parts of thecamera.
• Do not look at the sun or strong lights with thecamera. • Do not use or store the camera in dusty or humidplaces. • Do not cover the flash with a hand while firing.
• Use SD/SDHC/SDXC memory cards or Eye-Fi cardsonly. Never use other types of cards.If you accidently insert another type of card into thecamera, contact an authorized distributor or servicecenter. Do not try to remove the card by force. • If you find that the USB-AC adapter is extremelyhot or notice any unusual odors, noise, or smokearound it, unplug the power plug from wall outletimmediately and stop using it. Then, contact anauthorized distributor or service center.
CAUTION • Stop using the camera immediately if you notice anyunusual odors, noise, or smoke around it. • Never remove the batteries with bare hands, which maycause a fire or burn your hands. • Never hold or operate the camera with wet hands.This may cause overheating, exploding, burning,electrical shocks, or malfunctions.
• Do not leave the camera in places where it may besubject to extremely high temperatures. • Doing so may cause parts to deteriorate and, in somecircumstances, cause the camera to catch fire. Do notuse the charger or USB-AC adapter if it is covered(such as a blanket). This could cause overheating,resulting in fire.
If you hold on to the camera in this state, a low-temperature burn may be caused.
• In places subject to extremely cold temperatures,the temperature of the camera’s body may be lowerthan the environmental temperature. If possible,wear gloves when handling the camera in coldtemperatures.
• Be careful with the strap. • Be careful with the strap when you carry the camera. Itcould easily catch on stray objects and cause seriousdamage.
• To protect the high-precision technology contained in
this product, never leave the camera in the places listedbelow, no matter if in use or storage: • Places where temperatures and/or humidity are high orgo through extreme changes. Direct sunlight, beaches,locked cars, or near other heat sources (stove, radiator,etc.) or humidifiers. • In sandy or dusty environments. • Near flammable items or explosives. • In wet places, such as bathrooms or in the rain. Whenusing products with weatherproof designs, read their
manuals as well. • In places prone to strong vibrations.
• Never drop the camera or subject it to severe shocks orvibrations. • When attaching the camera to or removing it from atripod, rotate the tripod screw, not the camera. • Before transporting the camera, remove a tripod and allother non-OLYMPUS accessories. • Do not touch electric contacts on cameras. • Do not leave the camera pointed directly at the sun. This
may cause lens or shutter curtain damage, color failure,ghosting on the image pickup device, or may possiblycause fires. • Do not push or pull severely on the lens. • Before storing the camera for a long period, removethe batteries. Select a cool, dry location for storage toprevent condensation or mold from forming inside thecamera. After storage, test the camera by turning it onand pressing the shutter button to make sure that it isoperating normally.
• The camera may malfunction if it is used in a locationwhere it is subject to a magnetic/electromagnetic field, radiowaves, or high voltage, such as near a TV set, microwave,video game, loud speakers, large monitor unit, TV/radiotower, or transmission towers. In such cases, turn thecamera off and remove the battery, then reinsert it and turnthe camera on again before further operation
WARNING • Do not wet batteries with fluid such as water or seawater. • To prevent batteries from leaking, overheating,or causing a fire or explosion, use only batteriesrecommended for use with this product.
• Insert the battery carefully as described in the operating
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 70/78
70 EN
the camera on again before further operation. • Always observe the operating environment restrictions
described in the camera’s manual.
Battery Handling PrecautionsBattery Handling Precautions
Follow these important guidelines to preventbatteries from leaking, overheating, burning,exploding, or causing electrical shocks or burns.
DANGER
• The camera uses a lithium ion battery specified by Olympus.Charge the battery with the specified USB-AC adapteror charger. Do not use any other USB-AC adapters or chargers. • Never incinerate or heat batteries in microwaves, on hotplates, or in pressure vessels, etc. • Never leave the camera on or near electromagnetic devices.This may cause overheating, burning, or exploding. • Do not connect terminals with any metallic objects. • Take precautions when carrying or storing batteries toprevent them from coming into contact with any metal
objects such as jewelry, pins, fasteners, keys, etc.The short circuit may cause overheating, exploding, orburning, which burn or damage you. • Never store batteries where they will be exposed todirect sunlight, or subjected to high temperatures in a hotvehicle, near a heat source, etc. • To prevent causing battery leaks or damaging theirterminals, carefully follow all instructions regarding theuse of batteries. Never attempt to disassemble a batteryor modify it in any way, solder, etc.
• If battery fluid gets into your eyes, flush your eyesimmediately with clear, cold running water and seekmedical attention immediately. • Always store batteries out of the reach of small children.If a child accidentally swallows a battery, seek medicalattention immediately. • If you cannot remove the battery from the camera,contact an authorized distributor or service center. Do nottry to remove the battery by force.Damage to the battery exterior (scratches, etc.) may
produce heat or an explosion.
Insert the battery carefully as described in the operatinginstructions.
• If rechargeable batteries have not been recharged within thespecified time, stop charging them and do not use them. • Do not use a battery if it is cracked or broken. • If a battery leaks, has unusual odor, becomes discoloredor deformed, or becomes abnormal in any other wayduring operation, stop using the camera, and keep awayfrom fire immediately. • If a battery leaks fluid onto your clothing or skin, removethe clothing and flush the affected area with clean,running cold water immediately. If the fluid burns your
skin, seek medical attention immediately. • Never subject batteries to strong shocks or continuousvibration by dropping or hitting.This may cause exploding, overheating, or burning.
CAUTION • Before loading, always inspect the battery carefully forleaks, discoloration, warping, or any other abnormality. • The battery may become hot during prolonged use. Toavoid minor burns, do not remove it immediately after
using the camera. • Always unload the battery from the camera beforestoring the camera for a long period.Leaking and overheating may cause fire, injury, ormalfunction. • When storing the battery for a long period, select a coollocation for storage. • This camera uses one Olympus lithium ion battery. Usethe designated battery. There is a risk of explosion if thebattery is replaced with the incorrect battery type.
• Power consumption by the camera varies depending onwhich functions are used. • During the conditions described below, power isconsumed continuously and the battery becomesexhausted quickly. • The zoom is used repeatedly. • The shutter button is pressed halfway repeatedly inshooting mode, activating the auto focus. • A picture is displayed on the monitor for an extendedperiod of time.
• The camera is connected to a printer.
• Using an exhausted battery may cause the camera toturn off without displaying the battery level warning. • The Olympus lithium ion battery is designed to be usedonly for the Olympus digital camera.Do not use the battery to other devices. • If the battery’s terminals get wet or greasy, cameracontact failure may result Wipe the battery well with a
MonitorMonitor
• Do not push the monitor forcibly; otherwise the imagemay become vague, resulting in a playback mode failureor damage to the monitor. • A strip of light may appear on the top/bottom of themonitor, but this is not a malfunction.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 71/78
71EN
contact failure may result. Wipe the battery well with adry cloth before use.
• Always charge a battery when using it for the first time,or if it has not been used for a long period. • When operating the camera with battery power at lowtemperatures, try to keep the camera and spare batteryas warm as possible. A battery that has run down at lowtemperatures may be restored after it is warmed at roomtemperature. • Before going on a long trip, and especially beforetraveling abroad, purchase extra batteries. Arecommended battery may be dif ficult to obtain while
traveling. • Please recycle batteries to help save our planet’sresources. When you throw away dead batteries, be sureto cover their terminals and always observe local lawsand regulations.
USB-AC adapterUSB-AC adapter
• The included USB-AC adapter F-2AC is designed to beused only with this camera. Other cameras cannot be
charged with this USB-AC adapter. • Do not connect the included USB-AC adapter F-2AC toequipment other than this camera. • For plug-in type USB-AC adapter:The included USB-AC adapter F-2AC is intended to becorrectly orientated in a vertical or floor mount position.
Use Only Dedicated Rechargeable Battery,Use Only Dedicated Rechargeable Battery,
Battery Charger and USB-AC adapterBattery Charger and USB-AC adapter
We strongly recommend that you use only the genuineOlympus dedicated rechargeable battery, batterycharger and USB-AC adapter with this camera. Using anon-genuine rechargeable battery, battery charger and/or USB-AC adapter may result in fire or personal injurydue to leakage, heating, ignition or damage to the battery.Olympus does not assume any liability for accidents ordamage that may result from the use of a battery, batterycharger and/or USB-AC adapter that are not genuineOlympus accessories.
, • When a subject is viewed diagonally in the camera, the
edges may appear zigzagged on the monitor. This is nota malfunction; it will be less noticeable in playback mode. • In places subject to low temperatures, the monitor maytake a long time to turn on or its color may changetemporarily. When using the camera in extremely coldplaces, it is a good idea to occasionally place it in a warmplace. The monitor exhibiting poor performance due tolow temperatures will recover in normal temperatures. • The monitor of this product is manufactured with high-qualityaccuracy, however, there may be a stuck or dead pixel on
the monitor. These pixels do not have any influence onthe image to be saved. Because of the characteristics, theunevenness of the color or brightness may also be founddepending on the angle, but this is due to the structure ofthe monitor. This is not a malfunction.
Legal and Other NoticesLegal and Other Notices
• Olympus makes no representations or warranties regardingany damages, or benefit expected by using this unit lawfully,
or any request from a third person, which are caused by theinappropriate use of this product. • Olympus makes no representations or warranties regardingany damages or any benefit expected by using this unitlawfully which are caused by erasing picture data.
Disclaimer of WarrantyDisclaimer of Warranty
• Olympus makes no representations or warranties, eitherexpressed or implied, by or concerning any content ofthese written materials or software, and in no event shallbe liable for any implied warranty of merchantabilityor fitness for any particular purpose or for anyconsequential, incidental or indirect damages (includingbut not limited to damages for loss of business profits,business interruption and loss of business information)arising from the use or inability to use these writtenmaterials or software or equipment. Some countriesdo not allow the exclusion or limitation of liability forconsequential or incidental damages or of the implied
warranty, so the above limitations may not apply to you. • Olympus reserves all rights to this manual.
WarningWarning
Unauthorized photographing or use of copyrighted materialmay violate applicable copyright laws. Olympus assumes noresponsibility for unauthorized photographing, use or otheracts that infringe upon the rights of copyright owners.
For customers in North and South AmericaFor customers in North and South America
For customers in USADeclaration of ConformityModel Number: VR-370/D-785Trade Name: OLYMPUSResponsible Party:
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 72/78
72 EN
Copyright NoticeCopyright Notice
All rights reserved. No part of these written materials or thissoftware may be reproduced or used in any form or by anymeans, electronic or mechanical, including photocopying andrecording or the use of any type of information storage andretrieval system, without the prior written permission of Olympus.No liability is assumed with respect to the use of the informationcontained in these written materials or software, or for damagesresulting from the use of the information contained therein.Olympus reserves the right to alter the features and contents of
this publication or software without obligation or advance notice.
FCC NoticeFCC Notice
• Radio and Television Interference • Changes or modifications not expressly approved by themanufacturer may void the user’s authority to operate thisequipment. This equipment has been tested and found tocomply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interferencein a residential installation. • This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. • However, there is no guarantee that interference will notoccur in a particular installation. If this equipment doescause harmful interference to radio or television reception,which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interferenceby one or more of the following measures: • Adjust or relocate the receiving antenna. • Increase the distance between the camera and receiver. • Connect the equipment to an outlet on a circuit differentfrom that to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician forhelp. Only the OLYMPUS-supplied USB cable should be used toconnect the camera to USB enabled personal computers (PC).
Any unauthorized changes or modifications to thisequipment would void the user’s authority to operate it.
Responsible Party:
Address: 3500 Corporate Parkway, P.O. Box 610,Center Valley, PA 18034-0610, U.S.A.
Telephone Number: 484-896-5000
Tested To Comply With FCC StandardsFOR HOME OR OFFICE USE
This device complies with Part 15 of the FCC rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference.
(2) This device must accept any interference received,including interference that may cause undesiredoperation.
For customers in CANADAThis Class B digital apparatus complies with CanadianICES-003.
OLYMPUS WORLDWIDE LIMITED WARRANTY -
IMAGING PRODUCTSOlympus warrants that the enclosed Olympus® imagingproduct(s) and related Olympus® accessories (individuallya “Product” and collectively the “Products”) will be freefrom defects in materials and workmanship under normaluse and service for a period of one (1) year from the dateof purchase.If any Product proves to be defective within the one-yearwarranty period, the customer must return the defectiveProduct to any of Olympus Service Centers, following theprocedure set forth below (See “WHAT TO DO WHENSERVICE IS NEEDED”).Olympus, at its sole discretion, will repair, replace, oradjust the defective Product, provided that Olympusinvestigation and factory inspection disclose that (a) suchdefect developed under normal and proper use and (b)the Product is covered under this limited warranty.Repair, replacement, or adjustment of defective Productsshall be Olympus’s sole obligation and the customer’ssole remedy hereunder.
The customer is liable and shall pay for shipment of theProducts to the Olympus Service Center.Olympus shall not be obligated to perform preventivemaintenance, installation, deinstallation, or maintenance.Olympus reserves the right to (i) use reconditioned,refurbished, and/or serviceable used parts (that meetOlympus’s quality assurance standards) for warranty or
EXCEPT FOR THE LIMITED WARRANTY SET FORTH ABOVE, OLYMPUS MAKES NO AND DISCLAIMS ALL OTHER REPRESENTATIONS, GUARANTIES,CONDITIONS, AND WARRANTIES CONCERNINGTHE PRODUCTS, WHETHER DIRECT OR INDIRECT,EXPRESS OR IMPLIED, OR ARISING UNDER ANYSTATUTE, ORDINANCE, COMMERCIAL USAGE OR
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 73/78
73 EN
y p q y ) yany other repairs and (ii) make any internal or external
design and/or feature changes on or to its productswithout any liability to incorporate such changes on or tothe Products.
WHAT IS NOT COVERED BY THIS LIMITED
WARRANTYExcluded from this limited warranty and not warrantedby Olympus in any fashion, either express, implied, or bystatute, are:
(a) products and accessories not manufactured byOlympus and/or not bearing the “OLYMPUS” brandlabel (the warranty coverage for products andaccessories of other manufacturers, which may bedistributed by Olympus, is the responsibility of themanufacturers of such products and accessoriesin accordance with the terms and duration of suchmanufacturers’ warranties);
(b) any Product which has been disassembled, repaired,tampered with, altered, changed, or modified by
persons other than Olympus’s own authorized servicepersonnel unless repair by others is made with thewritten consent of Olympus;
(c) defects or damage to the Products resulting from wear,tear, misuse, abuse, negligence, sand, liquids, impact,improper storage, nonperformance of scheduledoperator and maintenance items, battery leakage, useof non-“OLYMPUS” brand accessories, consumables,or supplies, or use of the Products in combination withnon-compatible devices;
(d) software programs;(e) supplies and consumables (including but not limited to
lamps, ink, paper, film, prints, negatives, cables andbatteries); and/or
(f) Products which do not contain a validly placed andrecorded Olympus serial number, unless they are amodel on which Olympus does not place and recordserial numbers.
, ,OTHERWISE, INCLUDING BUT NOT LIMITED TO
ANY WARRANTY OR REPRESENTATION AS TO THESUITABILITY, DURABILITY, DESIGN, OPERATION,OR CONDITON OF THE PRODUCTS (OR ANY PARTTHEREOF) OR THE MERCHANTABILITY OF THEPRODUCTS OR THEIR FITNESS FOR A PARTICULARPURPOSE, OR RELATING TO THE INFRINGEMENT OF ANY PATENT, COPYRIGHT, OR OTHER PROPRIETARYRIGHT USED OR INCLUDED THEREIN.IF ANY IMPLIED WARRANTIES APPLY AS A MATTEROF LAW, THEY ARE LIMITED IN DURATION TO THE
LENGTH OF THIS LIMITED WARRANTY.SOME STATES MAY NOT RECOGNIZE A DISCLAIMEROR LIMITATION OF WARRANTIES AND/OR LIMITATIONOF LIABILITY SO THE ABOVE DISCLAIMERS ANDEXCLUSIONS MAY NOT APPLY.THE CUSTOMER MAY ALSO HAVE DIFFERENT AND/OR ADDITIONAL RIGHTS AND REMEDIES THAT VARYFROM STATE TO STATE.THE CUSTOMER ACKNOWLEDGES AND AGREESTHAT OLYMPUS SHALL NOT BE RESPONSIBLE FOR
ANY DAMAGES THAT THE CUSTOMER MAY INCURFROM DELAYED SHIPMENT, PRODUCT FAILURE,PRODUCT DESIGN, SELECTION, OR PRODUCTION,IMAGE OR DATA LOSS OR IMPAIRMENT OR FROM ANY OTHER CAUSE, WHETHER LIABILITY IS ASSERTED IN CONTRACT, TORT (INCLUDINGNEGLIGENCE AND STRICT PRODUCT LIABILITY)OR OTHERWISE. IN NO EVENT SHALL OLYMPUSBE LIABLE FOR ANY INDIRECT, INCIDENTAL,CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY
KIND (INCLUDING WITHOUT LIMITATION LOSS OFPROFITS OR LOSS OF USE), WHETHER OR NOTOLYMPUS SHALL BE OR SHOULD BE AWARE OFTHE POSSIBILITY OF SUCH POTENTIAL LOSS ORDAMAGE.
Representations and warranties made by any person, includingbut not limited to dealers, representatives, salespersons, oragents of Olympus, which are inconsistent or in conflict with or inaddition to the terms of this limited warranty, shall not be bindingupon Olympus unless reduced to writing and approved by anexpressly authorized of ficer of Olympus.This limited warranty is the complete and exclusive statement of
4 Sample prints, negatives, digital prints (or files on disk)if available and related to the problem.
When service is completed, the Product will be returned toyou postage prepaid.
WHERE TO SEND PRODUCT FOR SERVICESee “WORLDWIDE WARRANTY” for the nearest service
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 74/78
74 EN
warranty which Olympus agrees to provide with respect to the
Products and it shall supersede all prior and contemporaneousoral or written agreements, understandings, proposals, andcommunications pertaining to the subject matter hereof.This limited warranty is exclusively for the benefit of the originalcustomer and cannot be transferred or assigned.
WHAT TO DO WHEN SERVICE IS NEEDEDThe customer must transfer any image or other datasaved on a Product to another image or data storage
medium and/or remove any film from the Product prior tosending the Product to Olympus for service.
IN NO EVENT SHALL OLYMPUS BE RESPONSIBLE FORSAVING, KEEPING OR MAINTAINING ANY IMAGE OR DATASAVED ON A PRODUCT RECEIVED BY IT FOR SERVICE,OR ON ANY FILM CONTAINED WITHIN A PRODUCTRECEIVED BY IT FOR SERVICE, NOR SHALL OLYMPUS BERESPONSIBLE FOR ANY DAMAGES IN THE EVENT ANYIMAGE OR DATA IS LOST OR IMPAIRED WHILE SERVICE IS
BEING PERFORMED (INCLUDING, WITHOUT LIMITATION,DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL ORSPECIAL DAMAGES, LOSS OF PROFITS OR LOSS OF USE),WHETHER OR NOT OLYMPUS SHALL BE OR SHOULD BE AWARE OF THE POSSIBILITY OF SUCH POTENTIAL LOSSOR IMPAIRMENT.
Package the Product carefully using ample paddingmaterial to prevent damage in transit and either deliverit to the Authorized Olympus Dealer that sold you the
Product or ship it postage prepaid and insured to any ofour Olympus Service Centers.When returning Products for service, your package shouldinclude the following:1 Sales receipt showing date and place of purchase.2 Copy of this limited warranty bearing the Product
serial number corresponding to the serial numberon the Product (unless it is a model on which Olympusdoes not place and record serial numbers).
3 A detailed description of the problem.
See WORLDWIDE WARRANTY for the nearest service
center.
INTERNATIONAL WARRANTY SERVICEInternational warranty service is available under thiswarranty.
For customers in EuropeFor customers in Europe
“CE” mark indicates that this
product complies with the Europeanrequirements for safety, health,
environment and customer protection.
“CE” mark cameras are intended for
sales in Europe.
This symbol [crossed-out wheeled
bin WEEE Annex IV] indicates
separate collection of waste electricaland electronic equipment in the EU
countries.
Please do not throw the equipment into
the domestic refuse.
Please use the return and collection
systems available in your country for
the disposal of this product.
This symbol [crossed-out wheeledbin Directive 2006/66/EC Annex II]
indicates separate collection of waste
batteries in the EU countries.
Please do not throw the batteries into
the domestic refuse. Please use the
return and collection systems available
in your country for the disposal of the
waste batteries.
Provisions of warranty1 If this product proves to be defective, although it has been
used properly (in accordance with the written HandlingCare and Operating instructions supplied with it), during theapplicable national warranty period and has been purchasedfrom an authorized Olympus distributor within the businessarea of Olympus Europa Holding GmbH as stipulated on
e. Any defect that occurs due to careless or improperstorage (such as keeping the product under conditionsof high temperature and humidity, near insect repellentssuch as naphthalene or harmful drugs, etc.), impropermaintenance, etc.
f. Any defect that occurs due to exhausted batteries, etc.g. Any defect that occurs due to sand, mud, etc. entering
th i id f th d t i
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 75/78
75 EN
the website: http://www.olympus.com this product will be
repaired, or at Olympus’s option replaced, free of charge. Toclaim under this warranty the customer must take the productbefore the end of the applicable national warranty period tothe dealer where the product was purchased or any otherOlympus service station within the business area of OlympusEuropa Holding GmbH as stipulated on the website: http://www.olympus.com. During the one year period of the WorldWide Guarantee the customer may turn the product in at anyOlympus service station. Please notice that not in all countriessuch Olympus service station exists.
2 The customer shall transport the product to the dealer orOlympus authorized service station at his own risk andshall be responsible for any costs incurred in transportingthe product.
Provisions of Guarantee1 “OLYMPUS IMAGING CORP., 2951 Ishikawa-machi, Hachioji-
shi, Tokyo 192-8507, Japan grants a one year World WideGuarantee. This worldwide Guarantee must be presentedat an Olympus authorized repair service station before anyrepair can be made under conditions of this Guarantee. ThisGuarantee is valid only if the Guarantee Certificate and proofof purchase are presented at the Olympus repair servicestation. Please note that this Guarantee is in addition to anddoes not affect the customer’s legal warranty rights under theapplicable national legislation governing the sale of consumergoods mentioned above.
2 This Guarantee does not cover the following and the customerwill be required to pay repair charge, even for defectsoccurring within the Guarantee period referred to above.
a. Any defect that occurs due to mishandling (such asan operation performed that is not mentioned in theHandling Care or other sections of the instructions, etc.)
b. Any defect that occurs due to repair, modification,cleaning, etc. performed by anyone other than Olympusor an Olympus authorized service station.
c. Any defect or damage that occurs due to transport, afall, shock, etc. after purchase of the product.
d. Any defect or damage that occurs due to fire,earthquake, flood damage, thunderbolt, other natural
disasters, environmental pollution and irregular voltagesources.
the inside of the product casing.
h. When the Guarantee Certificate is not returned withthe product.
i. When any alterations whatsoever are made to theGuarantee Certificate regarding the year, month anddate of purchase, the customer’s name, the dealer’sname, and the serial number.
j. When proof of purchase is not presented with thisGuarantee Certificate.
3 This Guarantee applies to the product only; the Guaranteedoes not apply to any other accessory equipment, such as
the case, strap, lens cap and batteries.4 Olympus’s sole liability under this Guarantee shall be
limited to repairing or replacing the product. Any liabilityunder the Guarantee for indirect or consequential loss ordamage of any kind incurred or suffered by the customerdue to a defect of the product, and in particular any lossor damage caused to any lenses, films, other equipmentor accessories used with the product or for any lossresulting from a delay in repair or loss of data, is excluded.Compelling regulations by law remain unaffected by this.
Notes regarding Guarantee maintenance1 This Guarantee will only be valid if the Guarantee
Certificate is duly completed by Olympus or anauthorized dealer or other documents contain suf ficientproof. Therefore, please make sure that your name,the name of the dealer, the serial number and theyear, month and date of purchase are all completedor the original invoice or the sales receipt (indicatingthe dealer’s name, the date of purchase and product
type) is attached to this Guarantee Certificate. Olympusreserves the right to refuse free-of-charge service if
neither Guarantee Certificate is completed nor theabove document is attached or if the informationcontained in it is incomplete or illegible.
2 Since this Guarantee Certificate will not be re-issued,keep it in a safe place.
* Please refer to the list on the web site: http://www.olympus.com for the authorized international Olympusservice network.
For customers in AsiaFor customers in Asia
Provisions of warranty1 lf this product proves to be defective, although it has been
used properly (in accordance with the written HandlingCare and Operating instructions supplied with it), duringa period of up to one year from the date of purchase this
4 This Warranty applies to the product only; the Warrantydoes not apply to any other accessory equipment, such asthe case, strap, lens cap and batteries.
5 Olympus’ sole liability under this warranty shall be limited torepairing or replacing the product and any liability for indirector consequential loss or damage of any kind incurred orsuffered by the customer due to a defect in the product, andin partic lar an loss or damage ca sed to an film or lenses
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 76/78
76 EN
product will be repaired, or at Olympus’s option replaced,
free of charge. To claim under warranty the customer musttake the product and this Warranty certificate before theend of the one year warranty period to the dealer wherethe product was purchased or any Olympus authorizedservice station listed in the instructions and request thenecessary repairs.
2 The customer shall transport the product to the dealer orOlympus authorized service station at his own risk andshall be responsible for any costs incurred in transportingthe product.
3 This warranty does not cover the following and the customerwill be required to pay repair charge, even for defectsoccurring within the one year period referred to above.a. Any defect that occurs due to mishandling (such as
an operation performed that is not mentioned in theHandling Care or other sections of the instructions, etc.)
b. Any defect that occurs due to repair, modification,cleaning, etc. performed by anyone other than Olympusor an Olympus authorized service station.
c. Any defect or damage that occurs due to transport, a
fall, shock, etc. after purchase of the product.d. Any defect or damage that occurs due to fire,
earthquake, flood damage, thunderbolt, other naturaldisasters, environmental pollution and irregular voltagesources.
e. Any defect that occurs due to careless or improperstorage (such as keeping the product under conditionsof high temperature and humidity, near insect repellentssuch as naphthalene or harmful drugs, etc.), impropermaintenance, etc.
f. Any defect that occurs due to exhausted batteries, etc.g. Any defect that occurs due to sand, mud, etc. entering
the inside of the product casing.h. When this Warranty Certificate is not returned with the
product.i. When any alterations whatsoever are made to the
Warranty Certificate regarding the year, month and dateof purchase, the customer’s name, the dealer’s name,and the serial number.
j. When proof of purchase is not presented with thisWarranty Certificate.
in particular any loss or damage caused to any film or lenses
or other equipment or accessories used with the product or forany loss resulting from delay in repair, is excluded.
Notes;1 This Warranty is in addition to and does not affect the
customer’s statutory right.2 lf you have any queries regarding this Warranty, call any
of the Olympus authorized service stations listed in theinstructions.
Notes regarding warranty maintenance
1 This Warranty will only be valid if the Warranty Certificate isduly completed by Olympus or the dealer. Make sure that yourname, the name of the dealer, the serial number and the year,month and date of purchase are all completed.
2 Since this Warranty Certificate will not be re-issued, keep itin a safe place.
3 Any request for repair by a customer in same countrywhere the product was purchased shall be subject to theterms of the warranty issued by the Olympus distributor inthat country. Where the local Olympus distributor does not
issue a separate warranty or where the customer is not inthe country where the product was purchased the terms ofthis worldwide warranty shall apply.
4 Where applicable, this Warranty is valid worldwide. TheOlympus authorized service stations listed in this Warrantywill gladly honor it.
* Please refer to the appended list for the authorizedinternational Olympus service network.
Disclaimer of WarrantyOlympus makes no representations or warranties, eitherexpressed or implied, by or concerning any content if thesewritten materials or software, and in no event shall be liablefor any implied warranty of merchantability or fitness for anyparticular purpose or for any consequential, incidental orindirect damages (including but not limited to damages for lossof business profits, business interruption and loss of businessinformation) arising from the use of inability to use these writtenmaterials or software. Some states do not allow the exclusion orlimitation of liability for consequential or incidental damages, sothe above limitations may not apply to you.
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 77/78
8/9/2019 Olympus Vr-370 Manual En
http://slidepdf.com/reader/full/olympus-vr-370-manual-en 78/78
VM874401