1/3www.machinerylubrication.com/Read/754/oil-whirl-whip

Current Issue

ArchiveSubscribe

Search:

Oil Whirl and Whip Instabilities - WithinJournal Bearings

James E. Berry, Technical Associates of Charlotte

Tags: bearing lubrication

Oil whirl is probably the most common cause of subsynchronous instability in hydrodynamicjournal bearings. Typically, the oil film itself flows around the journal to lubricate and cool the

bearing. This develops an average speed slightly less than 50 percent of the journal surface

speed (Figure 1).

Normally, the shaft rides on the crest of an oil pressure gradient, rising slightly up the side of

the bearing somewhat off vertical at a given, stable attitude angle and eccentricity. The

amount of rise depends on the rotor speed, rotor weight and oil pressure. With the shaft

operating eccentrically relative to the bearing center, it draws the oil into a wedge to produce

this pressurized load-carrying film.

Figure 1. Oil Film Within a Journal 1

If the shaft receives a disturbing force such as a sudden surge or external shock, it can

momentarily increase the eccentricity from its equilibrium position. When this occurs,

additional oil is immediately pumped into the space vacated by the shaft. This results in an

increased pressure of the load-carrying film, creating additional force between the oil film and

shaft. In this case, the oil film can actually drive the shaft ahead of it in a forward circular

motion and into a whirling path around the bearing within the bearing clearance. If there is

sufficient damping within the system, the shaft can be returned to its normal position and

stability. Otherwise, the shaft will continue in its whirling motion, which may become violent

depending on several parameters.

Oil Whirl Instability Oil whirl demonstrates the following characteristics:

1. Oil whirl can be induced by several conditions including:

light dynamic and preload forces

excessive bearing wear or clearance

a change in oil properties (primarily shear viscosity)

an increase or decrease in oil pressure or oil temperature; improper bearing design

(sometimes an over design for the actual shaft loading)

fluid leakage in the shroud of blades and shaft labyrinth seals (so-called Alford force or

aerodynamic force)

change in internal damping (hysteretic, or material damping, or dry (coulomb) friction)

gyroscopic effects, especially on overhung rotors with excessive overhang.

Related Articles

Journal Bearings and Their Lubrication

When to Clean and Repack Bearings

How to Prevent Bearings from Overheating

Can WD40 be Used as a Bearing Lubricant?

White Papers

Home | Buyers Guide | Glossary | Events | Bookstore | Newsletters | Browse Topics

GREASES HYDRAULICS INDUSTRIAL LUBRICANTS SYNTHETICS FILTRATION STORAGE/HANDLING OIL ANALYSIS

2/3www.machinerylubrication.com/Read/754/oil-whirl-whip

Any of these conditions can induce oil whirl after a disturbing force induces an initial rotor

deflection.

2. Sometimes machines exhibit oil whirl intermittently due to external vibratory forces

transmitting into the unit or from sources within the machinery itself. In these cases, these

vibratory forces have the same frequency as the oil whirl frequency of that bearing and can

contribute just the right magnitude of disturbing force at just the right tuned frequency to set

the shaft into the whirl motion. This vibration transmits from other machinery through

attached structures such as piping and braces, or even through the floor and foundation. If

this occurs, it may be necessary to either isolate this machine from surrounding machinery, or

to isolate the offending machine itself.

3. Oil whirl is easily recognized by its unusual vibration frequency which is generally 40

percent to 48 percent of shaft RPM. (Reference 2 states that pure oil whirl occurs at 43

percent of shaft speed, but that the instability may occur at the first critical speed.)

4. Figure 2 shows the development of oil whirl just after the shaft is brought up to speed.

Note that the shaft went into whirl at a machine speed of approximately 1,800 RPM and

remained in whirl until about 4,000 RPM. At this point, note that the shaft 1X RPM speed

entered resonance, which actually generated sufficient force to overcome oil whirl. However,

once the machine passed through resonance, whirl once again occurred just above 5,200

RPM.

Figure 2. Development of Oil Whirl

Just After Startup; Followed by Oil Whip

from 9,200 to 12,000 RPM 3

5. Oil whirl is considered severe when vibration amplitudes reach 40 to 50 percent of the

normal bearing clearance. At this point, corrective action must be taken.

6. Temporary corrective measures include changing the temperature of the oil (thus, the oil

viscosity), purposely introducing a slight unbalance or misalignment to increase the loading,

temporarily shifting the alignment by heating or cooling support legs, scraping the sides of or

grooving the bearing surface to disrupt the lubricant wedge, or changing the oil pressure.

7. Permanent corrective steps to resolve the oil whirl problem include installing a new bearing

shell with proper clearances, preloading the bearing by an internal oil pressure dam, or

completely changing the bearing type to oil film bearings that are less susceptible to oil whirl

(including axial-groove bearings, lobed bearings or tilting pad bearings). The tilting pad bearing

is a good choice because each segment or pad develops a pressurized oil wedge tending to

center the shaft in the bearing, thereby increasing the system damping and overall stability.

Oil Whip Instability Oil whip occurs on those machines subject to oil whirl when the oil whirl frequency coincides

with and becomes locked into a systems natural frequency (often a rotor balance or critical

speed frequency). For example, refer to Figure 2. When the rotor speed increased to just

above 9,200 RPM, its speed increased to 2X its first balance natural frequency. At this time

the oil whirl which was approximately 43 percent of RPM, was brought into coincidence with

this critical speed. The oil whirl was suddenly replaced by oil whip - a lateral forward

precessional subharmonic vibration of the rotor. At this point, the oil whip frequency remains

the same, independent of the rotor RPM. Note that the oil whip frequency never changed

even though the machine continued up in speed to 12,000 RPM. When a shaft goes into oil

whip, its dominant dynamic factors become mass and stiffness in particular; and its amplitude

is limited only by the bearing clearance. Left uncorrected, oil whip may cause destructive

vibration resulting catastrophic failure often in a relatively short period of time.

Dry Whip Dry whip occurs in journal bearing machines subjected to either a lack of lubrication or the use

of the wrong lubricant. When this occurs, excessive friction is generated between the

stationary bearing and rotating journal. This friction can excite vibration in the bearing and

other components. This kind of vibration is called dry whip. Dry whip can also be caused by

journal bearings having excessive clearance as well as those having insufficient clearance.

Wear Debris Analysis: The Power ofKnowing More using Automated SEM/EDX

Top 7 Things a CMMS Can Do for YourOrganization

Buyers Guide

Grease Guns

Cleaners and Degreasers

Maintenance Services and Products

Poll

Which factor do you consider

to be the most influential on

the life of engine oil?

VoteVote

The engine's design and properties

Where and how the vehicle is driven

Selection of the engine oil and its

properties

Contact Us Share

Videos

3/3www.machinerylubrication.com/Read/754/oil-whirl-whip

The dry whip condition is similar to rubbing a moistened finger over a dry pane of glass. It will

generate a frequency specifically dependent upon the shaft and construction materials,

geometries and lubricant properties. Normally, this frequency will produce a high squealing

noise similar to that generated by dry rolling element bearings. The frequency content itself

will not be an integer multiple of the machine speed. When dry whip is suspected, it must be

taken care of quickly in order to prevent a potential catastrophic failure. And when dry whip is

suspected, both the lubricant itself and the lubrication system should be closely inspected

and the bearings should be checked to ensure they have proper clearances.

References

1. Berry, James E. Applications of Time Waveform Analysis. Analysis II Concentrated

Vibration Signature Analysis and Related Condition Monitoring Techniques. Chapter 6,

Pages 6-72 to 6-75, 2002.

2. Mitchell, John S. An Introduction to Machinery Analysis and Monitoring. Tulsa, Okla.:

Pennwell Publishing Co. Pages 141-151, 172-204, 1981.

3. Bently, Donald E.; Zimmer, Siegfried; Palmetier, George E.; and Muszynska, Agnes.

Interpreting Vibration Information from Rotating Machinery. Sound and Vibration

magazine. Volume 20, No. 2. Pages 14-23, February 1986.

Machinery Lubrication (5/2005)

Related Articles

Journal Bearings and Their Lubrication

When to Clean and Repack Bearings

How to Prevent Bearings from Overheating

Can WD40 be Used as a Bearing Lubricant?

Get 60 Questions to Ask Your Lubricant

Supplier absolutely FREE when you sign

up for our free Lube-Tips newsletter.Email:

Get Free Report

Lubrication Program TransformationServices Discover how Noria can tranform your lubrication

program to best practices quickly and efficiently.

Click Here

Begin a Free Subscription Today Machinery Lubrication magazine delivers

unbiased advice for improving lubrication

practices and keeping critical equipment

running at peak performance.

Click Here

NORIA CORPORATION MACHINERY LUBRICATION | RELIABLE PLANT

Services Subscribe | Contact Us | Privacy Policy | RSS | Advertise

Quick Links Home | Buyers Guide | Glossary | Events | Bookstore | Newsletters | Browse Topics

Like 670 people like this. Be the f irst of your friends.