nfusion step by step for n ewbie s - skyfiles by humannetwork rev 3 1 nfusion step by step for n...

Created by HumanNetwork http://f2atv.com Rev 3

1

NFUSION STEP BY STEP FOR NEWBIES Get your Nfusion Ready 2

Plug your NFusion to TV 2

CHECK BOOT VERSION 3

Connect NFusion to PC/Laptop 4

LOAD NEW BOOT BIN 5-7

LOAD THE LATEST SOFTWARE TO YOUR STB 8-9

CONNECT NFUSION TO TV AFTER LOAD S/W 10

CHECK BOOT AND S/W VERSION 11

FACTORY DEFAULT AFTER LOAD S/W 12

PROXY SETTING 13-14

EMULATOR 15

ANTENNA SETTING 16-22

MOTOR SETTINGS 23-29

HOW TO CHANGE PASSWORD 30-31

HOW TO SELECT INDIVIDUAL BIRD/TOTAL CHANNELS ON EACH BIRD

32-33

MANUALLY UPDATE EPG 34

HOW TO LOCK CHANNEL 35-38

SETTING LOCAL AREA 38-39

STB PICTURES 40--44


2

Get your Nfusion Ready.

Plug your NFusion to TV

Before you do anything.. you should verify that your NFusion should have the following:

- 1. Receiver - 1. Remote Control - 1. Red/White/Yellow cable - 1. RS232 NULL cable. - if you are lucky your dealer will included 1 4x1 switch.

Video/Audio Cable

Power

Download loader 1.0 and latest S/w ie. 145.2 from file section. Make sure you unzip them otherwise it won't work


3

CHECK BOOT VERSION

After you connect your Nfusion to your TV

Turn Nfusion ON from Rear Switch

Press Menu key on your remote

This is what you should see on your TV screen

On the Menu Screen

1. Scroll down to "System Settings" 2. Press OK 3. Scroll down to "S/W Version" 4. Press OK you will see the boot version, if you BOOT R3X less than 1.28 then you need to load boot 1.30 or later. if boot is "BOOT R3X 130" then you go ahead and load the latest software on it. i.e 145.2 Press Exit


4

RS232 NULL cable.

if you are using USB-RS232. make you have correct driver install.

Power cable

Connect NFusion to PC/Laptop

now connect your Nfusion to your computer or laptop to load bin and software. make sure you sue NULL cable that come with the box. do not use any other cable if you are too sure.

if you use USB-RS232 make sure you have a correct driver.

if you BOOT R3X 128 or later then skip LOAD NEW BOOT BIN on page 4. otherwise you need to load latest boot on page 4.


5

LOAD NEW BOOT BIN

Changed from Main->Boot

STEP1: Open N-Fusion loader v 1.0

STEP2: Click on Main>>it should change to Boot>>

STEP3: Click on Open File

STEP4: Browse to the newer boot file that you need to load. once you found that highlight it then click open


6

STEP5: Click on Start Nfusing button

STEP6: Press OK on your remote

STEP7: you need to recycle the main power switch from the back of STB (Set Top Box)

once the STB came back on, software automatically recognize your STB and it start to upload the boot file.


7

keep an eye on you STB LED, it should display Good after bin successfully write to your STB.

STEP8: Press OK after you've see Good on your STB.

I've seen so many ppl having problem loading boot, S/W via their pc. there are couple thing you have to keep in mind. make sure you use NULL cable came with nfusion box.. do not use different cable, even though it look similar, especially for those who owned different stb that use straight cable.

USB-Rs232 adaptor, this is the major issue that pple having with.. you have to make sure you load driver b4 you do anything else.. and make sure the port that your USB-RS232 is not taken by other devices.

To load S/W, leave your NFusion remain connected to your PC

To check boot version after loaded new boot, please refer back to "Check Boot Version"


8

LOAD THE LATEST SOFTWARE TO YOUR STB

Open N-Fusion v 1.0 Loader

Click on Open File

Browse to the file that you want to load, in this example we load v145.2

Click on the file then click Open

Leave everything as default

Click on Start NFusing


9

Press OK

Now turn off the main power switch from the back of your STB then turn it back on.

Once the STB came back on the loader automatically detect your STB and it start to upload the software to your STB

Keep an eye on your STB you should see the number on LED incrementing 1 at a time. once you see Good on your STB, it safe to click OK on your Loader

at this point you can disconnect your Nfusion from your computer. and connect it to your TV.


10

CONNECT NFUSION TO TV AFTER LOAD S/W

Video/Audio

Power RG6

Connect RJ-45 cable from your router to the back of your STB.

Hardwire, or connect to your wireless adaptor


11

CHECK BOOT AND S/W VERSION

Once you connect Nfusion to your TV, you should see MAIN MENU display on your TV screen. if not Press Menu on your remote

Scroll down to System Settings then press OK

Input your default password 0000

Scroll down to S/W Version then hit OK on your remote key.

Now you should see new Boot and S/W

You are successfully loaded software to your STB


12

FACTORY DEFAULT AFTER LOAD S/W

Menu->System Setting

password 0000

Scroll down o Factory Default press OK

STB should be reboot after you hit OK .


13

PROXY SETTING

By default Proxy is turn off after you load new S/W. but just incase you want to use proxy here is the guide.

For best practice, I would recommend you to change your proxy server at least once every couple of weeks. It is not a good idea to connect to only one proxy for ever.

To get to proxy screen

Menu->Internet->Proxy Connection

Press OK

On the same screen. Turn the Proxy ON Input the proxy server IP that you want to use. You need to put exactly what port that server use. in this example i use the following

IP: 148.233.159.58 Port: 0080 Press Exit when you done if you got the right proxy server, your stb should display picture in ~5sec after you pressed EXIT


14

Here is the list of working proxy and port.. you can use one of this in the list or find your own if you prefer. if you find one that cause a lot of freezing. then change to a different one.

PROXY SERVER IP PORT TYPE COUNTRY

218.206.074.075 0080 transparent China

193.093.104.101 8080 transparent Poland

148.233.159.058 0080 transparent Mexico

163.030.000.006 0080 transparent Taiwan

083.238.044.008 8080 transparent Poland

082.114.070.0098 8080 transparent Czechoslovakia



For more proxy list go to http://www.publicproxyservers.com/index.html

What is Proxy?

proxy server is a server (a computer system or an application program) which services the requests of its clients by forwarding requests to other servers. A client connects to the proxy server, requesting some service, such as a file, connection, web page, or other resource, available from a different server. The proxy server provides the resource by connecting to the specified server and requesting the service on behalf of the client.


15

EMULATOR

If you want to use IKS then it is very critical that you have to run EMULATOR = OFF.

Emulator= off meaning your using IKS server which is your Nfusion required connect to internet while viewing TV.

Emlator = ON meaning it is using stand alone bin.

I would recommend you to use IKS that way you can avoid ECM. let the server do the hard work :)

Menu->User Settings->Emulator


16

ANTENNA SETTING

110W and 119W stationary dish. in this example we going to use Single LNB type and DiCEqC 1.0/1.2.

I assumed that your physical dish properly setup. if not please setup your dish before doing the following steps.

STEP1: Press Menu key on your remote

Press OK on your Remote control key

STEP2: Input password 0000

0000 is the default password for nfusion


17

STEP3: Press OK on Antenna Setting

STEP4: Satellite is highlight, Press OK on your remote control


18

STEP5: Press double arrow down key on your remote until you see 110.0W ECHOSTAR 8/1 then press OK on your remote control.

LNB Type = 1. Standard LOFreq = 11250 22KHz = OFF DiSEqC Mode = Port 2 (I used port 2 for 110. set this according to your physical port setting.) Multi-Dish Switch = Disable Motor Settings = OFF LNB Power = ON you should see EchoStar 110 banner popup on your screen. S and Q also have green bar. S = Signal Q= Quality. we are not too concern about the Q. we more concern about S. The higher the S is better.

if you own other STB you might see their signal better than NFusion, but I won't worry about it if I were you. as long as your dish setup properly.


19

STEP6: Now press Menu once on your remote control.

STEP7: Press OK on your remote control to save.

STEP8: Press OK on your remote control again to get back into Antenna Setting


20

STEP9: Scroll down to Search Channels CH All Search then press OK to search auto scan 110W.

STB scanning the selected bird.

sit back and watch the channels coming through :)


21

Once Auto Scan is done STB automatically update itself and it will automatically exit itself.

Screen after scanned.


22

SETUP 119W

Repeat the same process as 110W. The only difference is your PORT setting. Change the port setting to correspond with your physical setup. LNB Type = 1. Standard LOFreq = 11250 22KHz = OFF DiSEqC Mode = Port 3 (I used port 3 for 119. set this according to your physical port setting.) Multi-Dish Switch = Disable Motor Settings = OFF LNB Power = ON


23

MOTOR SETTINGS

I'm assuming that you have your physical motor setup at this point. you also should know your Long and Lat. if you don't you can google your zip and it will tell you exactly what that is.

in this walkthrough, we are going to use 82.7W longitude and 27.8N for latitude.

I'm going to aim 91W for this walkthrough.

STEP1: Press MENU on your remote control.

STEP2: Press OK on your Remote control


24

STEP3: input password 0000

STEP4: Press OK on Antenna Setting


25

STEP5: Satellite is highlight, Press OK on your remote control

STEP6: Press double arrow down key on your remote until you see 91.0W NIMIQ1 KU then press OK on your remote control.


26

LNB Type = 1. Standard LOFreq = 11250 22KHz = OFF DiSEqC Mode = Port 1 (I used port 1 for 91W and all of my Circular birds, and port 4 for my Linear birds. set this according to your physical port setting. motor is a little bit different from stationary dish. all of the C birds share a common port vs L birds.) Multi-Dish Switch = Disable Motor Settings = Usals (press vol key on your remote to cycle thru) LNB Power = ON STEP7: Press OK on Motor Settings = Usals

STEP8: Press Ok. Now input your Long/Lat, use your keys on the remote to input the value. My Longitude = 082.7W My Latitude = 27.8N Press Vol key to select (W/E or N/S)


27

Once you input the value correctly scroll down to Goto Sat Position

STEP9: Press OK.

you won't see the motor moving, just wait for ~30sec you should see S&Q are green and NIMIQ1 also lock.

STB locked your selected SAT


28

STEP10: Press Menu on your remote to return to a previous screen.

STEP11: Press Menu on your remote to save the Sat posistion.

STEP12: Press OK to save.

STEP13: Antenna Setting is highlight, Press OK


29

Now you see that your STB locked 91W

STEP14: Scroll down to Search Channels then press OK to auto search on 91W

Now kick back and relax, your STB is scanning 91W. once it done scanning it will automatically update itself.

That is how you set your motor with NFusion STB.

you only need to input Long/Lat once. To set another bird using motor repeat STEP1 - STEP14, except STEP8:


30

HOW TO CHANGE PASSWORD

Press Menu on your remote

Scroll down to User Settings then Press OK

Scroll down to Parental Control then press OK


31

Input your password (default password is 0000

Scroll down to New Password enter your new password and Confirm New

make sure they both identical.


32

HOW TO SELECT INDIVIDUAL BIRD/TOTAL CHANNELS ON EACH BIRD

Press GUIDE key on your remote

Press AUDIO key (green)

On the left you should see the list of your birds. In this case 119.0W and 91.0W

On the right you should see total of your channels on each birds.


33

MANUALLY UPDATE EPG

Press GUIDE key on your remote

Press LANG key (blue)

Your EPG is updating

This is what it should look like after it done.


34

HOW TO LOCK CHANNEL

Press MENU on remote control

Scroll down to Edit TV/Radio List

Press OK

Enter your password, default password is 0000

Scroll down the channel you want to lock then press OK.

you should see the lock symbol appear on the selected channels.


35

HOW TO ADD CHANNELS TO FAV GROUP

When done lock your channel.

Press MENU button on your remote.

Press OK to save

Press MENU key on your remote.

scroll down to Edit Favorite List

Enter Password (0000 default password)


36

Press right vol key on your remote to

press OK rename your favorite group.

Once you've done your group name.

press MENU key go get back previous screen


37

To add Favorite channel.

press left vol key to

now scroll down the your fav channel then press OK.

once you've done press Menu key to get out.

Press OK to save.

repeat the same process for another favorite group.

you can add up to 8 favorite groups.


38

SETTING LOCAL AREA

Press MENU key on your remote.

scroll down User Settings

Press OK

Local Area is highlight, Press OK


39

Scroll down to you State.

Press right VOL key once to select your city

Select your city, Press OK

Press OK to save your local area


40

STB PICTURES


41


42


43


44

nfusion step by step for n ewbie s - skyfiles by humannetwork rev 3 1 nfusion step by step for n...

Documents