MultiConnect® rCell 100 Series Router (H5, H6,G3)MTR-H5, MTR-H6 and MTR-G3 Quick Start

MultiConnect® rCell 100 Series Router (H5, H6, G3) MultiTech Systems MultiConnect® rCell 100 Series Router (H5, H6, G3) MultiTech Systems MultiConnect® rCell 100 Series Router (H5, H6, G3) MultiTech Systems

Quick Start Quick Start Quick Start

Right Side Panel for MTR-H5 and MTR-H6

Right Side Panel for MTR-G3

Side PanelsThe device has connectors on both sides of the housing. The right side ofthe device contains a reset button, WiFi, Auxiliary (for Diversity), GPS,and Cellular connectors for H5/H6. For G3, only the Cellluar connector isavailable. Depending on the model, GPS or WiFi connectors may or maynot be present. The left side of the device includes an RS-232 connector,an Ethernet connector, and the power receptacle.

Installing the Router1. To use the router’s cellular features, connect a suitable

antenna to the antenna connector.2. Using an Ethernet cable, connect one end of the cable to

the E-NET connector on the back of the router and the otherend to your computer, directly or through a switch or hub.

3. If you are connecting to a serial interface, connect the DE-9connector (9-pin) of the RS-232 cable to the RS-232connector on the router. Then connect the other end to theserial port on the desired device.

4. Some routers support the use of a GPS receiver includingB08 and B10 for H5 and B19 for H6. If you are using a GPSreceiver with the router, attach the GPS cable to the GPSconnector.

5. Some routers support the use of WiFi including B09 andB10 for H5 and B18 and B19 for H6. If you are using WiFiwith the router, attach the WiFi antenna to the WIFIconnector.

6. Screw on power lead from power supply module into powerconnection. Plug power supply into power source.

■ POWER LED lights after the device powers up.■ When STATUS LED blinks, the device is ready

for use.7. You can configure your device by using its web

management interface. You may need to change the IPaddress of your computer to be in the same IP and subnetmask range as the device.

a. Open web browser. In address field, type defaultaddress for the device: http://192.168.2.1. (If thebrowser displays a message about a problem with thesecurity certificate, ignore and click Continue).

b. For G3, a login page opens. Enter the defaultusername: admin (all lower-case). Then, enter thedefault password: admin (all lower-case). Click Login.

c. For H5/H6, when logging in for the first time, thedevice enters commissioning mode requiring ausername and password for an admin user account.Enter and submit your desired username andpassword. Confirm the password.

d. Refer to the appropriate user guide for further detailson first-time setup.

MultiConnect® rCell 100 Series Router(MTR-H5/H6/G3)Part Number: 82102102L Rev. 3

Copyright and TrademarksThis publication may not be reproduced, in whole or in part, without thespecific and express prior written permission signed by an executiveofficer of Multi-Tech Systems, Inc. All rights reserved. Copyright © 2018by Multi-Tech Systems, Inc.

Multi-Tech Systems, Inc. makes no representations or warranties,whether express, implied or by estoppels, with respect to the content,information, material and recommendations herein and specificallydisclaims any implied warranties of merchantability, fitness for anyparticular purpose and non-infringement. Multi-Tech Systems, Inc.reserves the right to revise this publication without obligation to notify anyperson or organization of such revisions or changes.

MultiConnect, MultiTech and the MultiTech logo are registeredtrademarks of Multi-Tech Systems, Inc. All other brand and productnames are trademarks or registered trademarks of their respectivecompanies.

MultiConnect® rCell 100 Series Router (H5, H6, G3) MultiTech Systems MultiConnect® rCell 100 Series Router (H5, H6, G3) MultiTech Systems MultiConnect® rCell 100 Series Router (H5, H6, G3) MultiTech Systems MultiConnect® rCell 100 Series Router (H5, H6, G3) MultiTech Systems

Quick Start Quick Start Quick Start Quick Start

OverviewThe MultiConnect® rCell 100 Series Router (MTR-H5, MTR-H6, MTR-G3)provides secure data communication between many types of devices thatuse legacy and the latest communication technologies.

47 CFR Part 15 Regulation Class B DevicesThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.■ Increase the separation between the equipment and receiver.■ Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.■ Consult the dealer or an experienced radio/TV technician for

help.

Warning: Changes or modifications to this unit not expressly approved bythe party responsible for compliance could void the user’s authority tooperate the equipment.

EMC, Safety, and Radio Equipment Directive (RED)Compliance - H5 and H6MultiTech declares that this device is in compliance with the essentialrequirements and other relevant provisions of Directive 2014/53/EU. Thedeclaration of conformity may be requested athttps://support.multitech.com.

Package ContentsYour MultiConnect® rCell 100 Series Router (MTR-H5, MTR-H6, MTR-G3) typically includes the following (varies with model):

PowerSupply

1 - 9 VDC power supply with removable blades, 1 -NAM blade/plug, 1 - EURO blade/plug, 1 - UKblade/plug, 1-AU/NZ blade/plug

Cables 1 -Ethernet cable with RJ-45 connector, 1 - Powercable from power supply

Antennas 1 - CELL, For H5: Hepta Band SM external antenna,For H6 and G3: Penta Band external antenna, 1 -GPS external antenna, and 1 - WIFI external antenna

Documents 1 - Quick Start, 1 - Warranty Plans, 1 - Activation,Support & Regulatory Information

Other Items 1 - Mounting rod, 4 - Clear adhesive bumpons ormounting feet

Device 1- MultiConnect® rCell 100 Series Router (H5, H6,G3) 4.169" x 3.00" x 1.163" Blue enclosure includes:

■ 7-32 VDC power connector■ RS-232 (DE 9-pin, female-D) connector■ E-NET RJ-45 receptacle for standard

Ethernet 10/100 Base-T■ WIFI WiFi male SMA connector (for H5

and H6 only)■ AUX Cellular auxiliary female SMA

connector (Diversity - H5 and H6 only)■ GPS GPS female SMA connector (B08

and B10 for H5 and B19 for H6)■ CELL Cellular female SMA connector

Additional InformationFor the latest information on your device including operation, regulatory,and safety topics, refer to the appropriate user guide online:

http://www.multitech.com/brands/multiconnect-rcell-100-series

LED DescriptionsThe top panel contains the following LEDs:

■ Power and Status LEDs - The Power LED indicates that DCpower is present and the Status LED blinks when the unit isfunctioning normally.

■ WiFi LED - The WiFi LED indicates that WiFi is enabled (H5and H6 only).

■ Modem LEDs - Two modem LEDs indicate carrier detectionand link status.

■ Signal LEDs - Three signal LEDs display the signal strengthlevel of the wireless connection.

■ Ethernet LEDs - These LEDs are not on the top panel. Thetwo Ethernet LEDs are physically on the RJ-45 connector(s).

■ Ethernet Link LED - Located on the right on the Ethernetconnector. This LED blinks when there is transmit andreceive activity and is steady when there is a valid Ethernetconnection.

■ Ethernet Speed LED - Located on the left on the Ethernetconnector. When lit the Ethernet is linked at 100Mbps. If it isnot lit, the Ethernet is linked at 10 Mbps.

Installing a SIM CardIf you want to operate the router on a particular cellular network, install amini-SIM card [or mini SIM (2FF) form factor].

To install the SIM:

1. Locate the SIM card slot on the side of the router. The slotis labeled SIM.

2. Push the SIM card into the slot until it snaps into place.

Mounting Device1. Locate the groove on the bottom of the modem.2. Slide the mounting rod through the groove.3. To secure the rod to the desired surface, place and tighten

two screws in the holes on either end of the mounting rod.Refer to the user guide for an illustration of the mountingrod, as well as the dimensions for placement of the screws.