mtb100 quick manual track & trace device v1 quick man… · quick sms configuration . default...
TRANSCRIPT
![Page 1: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/1.jpg)
Quick Manual
v1.5 Track & trace device
MTB100
![Page 2: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/2.jpg)
2 MTB100 | Wiki
Table of Contents Know your device ............................................................................... 3
Pinout ................................................................................................. 4
Wiring scheme ................................................................................... 5
Set up your device ............................................................................. 6
How to insert SIM card and connect the battery ........................... 6
PC Connection (Windows) ................................................................ 7
How to install USB drivers (Windows) ............................................. 7
Configuration (Windows) ................................................................. 7
Quick SMS configuration .................................................................. 9
Mounting recommendations .......................................................... 10
LED indications ................................................................................. 11
Characteristics .................................................................................. 11
Basic characteristics ....................................................................... 11
Electrical characteristics ................................................................. 12
Safety information ........................................................................... 14
Certification and Approvals ............................................................. 15
Warranty ........................................................................................... 16
Warranty Disclaimer........................................................................ 16
![Page 3: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/3.jpg)
3 MTB100 | Wiki
Know your device
Figure 1 MTB100 device view
![Page 4: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/4.jpg)
4 MTB100 | Wiki
Pinout
Table 1 MTB100 pinout
PIN NUMBER PIN NAME DESCRIPTION
1 VCC (6-30) V DC (+) Power supply (6-30) V DC (+)
2 GND (-) Ground pin
3 DIN 1 Digital input, channel 1. DEDICATED
FOR IGNITION INPUT
4 AIN 1 Analog input, channel 1. Input range: 0-
30 V DC
5 DOUT 1 Digital output, channel 1. Open
collector output. Max. 0,5 A DC Figure 2 MTB100 pinout
![Page 5: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/5.jpg)
5 MTB100 | Wiki
Figure 3 MTB100 Wiring scheme
Wiring scheme
1 Automotive relay
^1
![Page 6: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/6.jpg)
6 MTB100 | Wiki
Set up your device
How to insert Micro SIM card and
connect the battery
1. Gently remove MTB100 cover using plastic pry tool from both
sides.
2. Insert Micro-SIM card as shown with PIN request disabled or
read Security info how to enter it later in Configurator. Make sure
that Micro-SIM card cut-off corner is pointing forward to slot.
3. Connect battery as shown to device. Position the battery in
place where it does not obstruct other components.
4. Attach device cover back. Device is ready to be connected.
Figure 4 Cover removal Figure 5 Micro SIM card insert
Figure 6 Battery connection Figure 7 Attaching cover back
![Page 7: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/7.jpg)
7 MTB100 | Wiki
PC Connection (Windows)
1. Power-up MTB100 with DC voltage 6-30 V power supply using
power cable. LED’s should start blinking, see “LED indications”.
2. Connect device to computer using Micro-USB cable or
Bluetooth connection:
• Using Micro-USB cable
▬ You will need to install USB drivers, see "How to install
USB drivers (Windows)"
• Using Bluetooth
▬ MTB100 Bluetooth is enabled by default. Turn on
Bluetooth on your PC, then select Add Bluetooth or other
device > Bluetooth. Choose your device named –
“MTB100_last_7_imei_digits”, without LE in the end. Enter
default password 5555, press Connect and then select
Done.
3. You are now ready to use the device on your computer.
How to install USB drivers
(Windows)
1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
setup.
Configuration (Windows)
At first MTB100 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator
software. Get the latest MTB100 Configurator version from here.
Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct
version installed. Table 2 MS .NET requirements
MS .NET REQUIREMENTS
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2 32 and 64 bit www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can
be changed by clicking in the right bottom corner (Figure 8
Language selection).
![Page 8: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/8.jpg)
8 MTB100 | Wiki
Configuration process begins by pressing on connected device
(Figure 9 Device connected via USB).
After connection to Configurator Status window will be displayed
(Figure 10 Configurator Status window).
Various Status window tabs display information about GNSS, GSM,
I/O, Maintenance and etc. MTB100 has one user editable profile,
which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
functionality:
1. Load from device – loads configuration from device.
2. Save to device – saves configuration to device.
3. Load from file – loads configuration from file.
4. Save to file – saves configuration to file.
5. Update firmware – updates firmware on device.
6. Read records – reads records from the device.
7. Reboot device – restarts device.
8. Reset configuration – sets device configuration to
default.
Most important configurator section is GPRS – where all your
server and GPRS settings can be configured and Data Acquisition –
where data acquiring parameters can be configured.
More details about MTB100 configuration using Configurator can
be found in our Wiki.
Figure 9 Device connected via USB
Figure 8 Language selection
Figure 10 Configurator Status window
![Page 9: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/9.jpg)
9 MTB100 | Wiki
Quick SMS configuration
Default configuration has optimal parameters present to ensure
best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS settings:
• 2001 – APN
• 2002 – APN username (if there
are no APN username, empty
field should be left)
• 2003 – APN password (if there
are no APN password, empty
field should be left)
Server settings:
• 2004 – Domain
• 2005 – Port
• 2006 – Data sending protocol
(0 – TCP, 1 – UDP)
Default configuration settings
Movement and ignition detection:
Vehicle movement will
be detected by
accelerometer
Ignition will be detected
by vehicle power voltage
between 13,2 – 30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes
Vehicle turns 10 degrees
Vehicle drives 100
meters
Speed difference
between last coordinate
and current position is
greater than 10 km/h
Device makes a record On Stop if:
1 hour passes while
vehicle is stationary
and ignition is off
Records sending to server:
If device has made a
record it is sent to the
server every 120
seconds
After successful SMS configuration, MTB100 device will synchronize
time and update records to configured server. Time intervals and
default I/O elements can be changed by using Teltonika
Configurator or SMS parameters
" setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0;"
![Page 10: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/10.jpg)
10 MTB100 | Wiki
Mounting recommendations • Connecting wires
▬ Wires should be fastened to the other wires or non-moving
parts. Try to avoid heat emitting and moving objects near
the wires.
▬ The connections should not be seen very clearly. If factory
isolation was removed while connecting wires, it should be
applied again.
▬ If the wires are placed in the exterior or in places where they
can be damaged or exposed to heat, humidity, dirt, etc.,
additional isolation should be applied.
▬ Wires cannot be connected to the board computers or
control units.
• Connecting power source
▬ Be sure that after the car computer falls asleep, power is still
available on chosen wire. Depending on car, this may
happen in 5 to 30 minutes period.
▬ When the module is connected, measure the voltage again
to make sure it did not decrease.
▬ It is recommended to connect to the main power cable in
the fuse box.
▬ 3 A, 125 V external fuse shall be used.
• Connecting ignition wire
▬ Be sure to check if it is a real ignition wire i.e. power does
not disappear after starting the engine.
▬ Check if this is not an ACC wire (when key is in the first
position, most of the vehicle electronics are available).
▬ Check if power is still available when you turn off any of
vehicles devices.
▬ Ignition is connected to the ignition relay output. As
alternative, any other relay, which has power output when
ignition is on, may be chosen.
• Connecting ground wire
▬ Ground wire is connected to the vehicle frame or metal
parts that are fixed to the frame.
▬ If the wire is fixed with the bolt, the loop must be connected
to the end of the wire.
▬ For better contact scrub paint from the spot where loop is
going to be connected.
![Page 11: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/11.jpg)
11 MTB100 | Wiki
LED indications
Table 3 Status LED indications
BEHAVIOR MEANING
Blinking every second Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
Off Device is not working or Device is in
boot mode
2 Expected time in conditions with good GNSS satellites visibility
Characteristics
Basic characteristics
Table 4 Basic characteristics
MODULE
Name Teltonika TM2500
Technology GSM, GPRS, GNSS, BLUETOOTH
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS, AGPS
Receiver Tracking: 33
Tracking sensitivity -165 dBM
Accuracy < 3 m
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s2
CELLULAR
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer
GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support SMS (text/data)
POWER
![Page 12: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/12.jpg)
12 MTB100 | Wiki
Input voltage range 6-30 V DC with overvoltage protection
Back-up battery 170 mAh Li-Ion battery 3.7 V (0.63 Wh)
Power consumption
At 12V < 2 mA (Ultra Deep Sleep)
At 12V < 4 mA (Deep Sleep)
At 12V < 5 mA (Online Deep Sleep
At 12V < 6 mA (GNSS Sleep)
At 12V < 25 mA (nominal with no load)
BLUETOOTH
Specification 4.0 + LE
Supported peripherals
Temperature and Humidity sensor,
Headset, OBDII dongle, Inateck
Barcode Scanner, Universal BLE
sensors support
INTERFACE
Digital Inputs 1
Digital Outputs 1
Analog Inputs 1
GNSS antenna Internal High Gain
GSM antenna Internal High Gain
USB 2.0 Micro-USB
LED indication 1 status LED light
SIM Micro-SIM
Memory 128MB internal flash memory
PHYSICAL SPECIFICATION
Dimensions 78.4 x 42.6 x 21 mm (L x W x H)
Weight 69 g
OPERATING ENVIRONMENT
Operating temperature (without
battery) -40 °C to +85 °C
Storage temperature (without battery) -40 °C to +85 °C
Operating humidity 5% to 95% non-condensing
Ingress Protection Rating IP54
Battery charge temperature 0 °C to +45 °C
Battery discharge temperature -20 °C to +60 °C
Battery storage temperature -20 °C to +45 °C for 1 month
-20 °C to +35 °C for 6 months
FEATURES
Sensors Accelerometer
Scenarios
Green Driving, Over Speeding
detection, Jamming detection, GNSS
Fuel Counter, DOUT Control Via Call,
Excessive Idling detection, Unplug
detection, Towing detection, Crash
detection, Auto Geofence, Manual
Geofence, Trip
Sleep modes GPS Sleep, Online Deep Sleep, Deep
Sleep, Ultra Deep Sleep
Configuration and firmware update
FOTA Web, FOTA, Teltonika
Configurator (USB, Bluetooth), FMBT
mobile application (Configuration)
SMS Configuration, Events, DOUT control,
Debug
GPRS commands Configuration, DOUT control, Debug
Time Synchronization GPS, NITZ, NTP
Fuel monitoring LLS (Analog), OBDII dongle
Ignition detection
Digital Input 1, Accelerometer, External
Power Voltage, Engine RPM (OBDII
dongle)
Electrical characteristics
![Page 13: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/13.jpg)
13 MTB100 | Wiki
Table 5 Electrical characteristics
CHARACTERISTIC DESCRIPTION VALUE
MIN. TYP. MAX. UNIT
SUPPLY VOLTAGE
Supply Voltage (Recommended Operating
Conditions) +6 +30 V
DIGITAL OUTPUT (OPEN DRAIN GRADE)
Drain current (Digital Output OFF) 120 µA
Drain current (Digital Output ON,
Recommended Operating Conditions) 0.6 A
DIGITAL INPUT
Input resistance (DIN1) 47 kΩ
Input voltage (Recommended Operating
Conditions) 0
Supply
voltage V
Input Voltage threshold (DIN1) 3.9 V
ANALOG INPUT
Input voltage (Recommended Operating
Conditions) 0 +30 V
Input resistance 150 kΩ
Measurement error on 12V 3 %
Additional error on 12 V 360 mV
Measurement error on 30 V 3 %
Additional error on 30 V 900 mV
ABSOLUTE MAXIMUM RATINGS
Supply Voltage -32 +32 V
Drain-Source clamp threshold voltage,
(Idrain = 2 mA) +36 V
Digital Input Voltage -32 +32 V
Analog Input Voltage -32 +32 V
Analog Input error margin can increase if temperature
varies.
![Page 14: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/14.jpg)
14 MTB100 | Wiki
Safety information
This message contains information on how to operate MTB100 safely. By
following these requirements and recommendations, you will avoid
dangerous situations. You must read these instructions carefully and
follow them strictly before operating the device!
• The device uses SELV limited power source. The nominal voltage is
+12 V DC. The allowed voltage range is +6 ...+30 V DC.
• To avoid mechanical damage, it is advised to transport the device in
an impact-proof package. Before usage, the device should be placed
so that its LED indicators are visible. They show the status of device
operation.
• When connecting the (1x5) cables to the vehicle, the appropriate
jumpers of the vehicle power supply should be disconnected.
• Before dismounting the device from the vehicle, the 1x5 connection
must be disconnected.
• The device is designed to be mounted in a zone of limited access,
which is inaccessible to the operator. All related devices must meet
the requirements of EN 60950-1 standard.
• The device MTB100 is not designed as a navigational device for boats.
Do not disassemble the device. If the device is
damaged, the power supply cables are not isolated or
the isolation is damaged, DO NOT touch the device
before unplugging the power supply.
All wireless data transferring devices produce
interference that may affect other devices which are
placed nearby.
The device must be connected only by qualified
personnel.
The device must be firmly fastened in a predefined
location.
The programming must be performed using a PC
with autonomic power supply.
Installation and/or handling during a lightning storm
is prohibited.
The device is susceptible to water and humidity.
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to the
instructions.
Battery should not be disposed of with general
household waste. Bring damaged or worn-out
batteries to your local recycling center or dispose
them to battery recycle bin found in stores.
![Page 15: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/15.jpg)
15 MTB100 | Wiki
Certification and Approvals
This sign on the package means that it is
necessary to read the User‘s Manual before
your start using the device. Full User‘s Manual
version can be found in our Wiki.
This sign on the package means that all used
electronic and electric equipment should not be
mixed with general household waste.
Hereby, Teltonika declare under our sole
responsibility that the above described product
is in conformity with the relevant Community
harmonization: European Directive 2014/53/EU
(RED).
![Page 16: MTB100 Quick Manual Track & trace device v1 Quick Man… · Quick SMS configuration . Default configuration has optimal parameters present to ensure best performance of track quality](https://reader034.vdocuments.site/reader034/viewer/2022052615/608351189233962ac43df6e7/html5/thumbnails/16.jpg)
16 MTB100 | Wiki
Warranty TELTONIKA guarantees its products to be free of any
manufacturing defects for a period of 24 months. With additional
agreement we can agree on a different warranty period, for more
detailed information please contact our sales manager.
Contact us teltonika.lt/company/contacts
All batteries carry a reduced 6 month warranty period.
If a product should fail within this specific warranty time, the
product can be:
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfilling the same
functionality
• TELTONIKA can also repair products that are out of warranty at
an agreed cost.
Warranty Disclaimer TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS
WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE
LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED
WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED.
ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND
ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT
NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME,
INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.
More information can be found at teltonika.lt/warranty-repair