monthly notifications register - sutn · monthly notifications register ... additional provision...
TRANSCRIPT
Information procedure Page 1
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Register issued on : 2010-06-04
A list of subsectors can be found at the end of this document.
Information procedure Page 2
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector A : SERVICES
Register issued on : 2010-06-04
Page 3Subsector A03: POSTAL SERVICES
Subsector : A03 Registration Date : 2010-05-24Organization : SUTNCountry : SlovakiaProject ID : 88000110/0001 Project EstablishedICS : 03.220, 55.040National Ref : STN 88 5401/Z2Title : Covers and forms for mail item. Correspondence envelopes Scope : The main reason for amendment is to eliminate pre-print frame for postcode from address
side of envelope, postcard picture, postcard, that cause difficulty with automated operation of the mail items. The amendment follows STN 88 5420/A2 Covers and forms for mail item. Postcards and picture postcards. Amendment 2
Relatedness :National : REV/AMD STN 88 5401
Subsector : A03 Registration Date : 2010-05-24Organization : SUTNCountry : SlovakiaProject ID : 88000210/0001 Project EstablishedICS : 03.220, 55.040National Ref : STN 88 5420/Z2Title : Covers and forms for mail item. Postcards and picture postcards Scope : The main reason for amendment is to eliminate pre-print frame for postcode from address
side of envelope, postcard and picture postcard, that cause difficulty with automated operation of the mail items. The amendment follows STN 88 5401/A2 Covers and forms for mail item. Correspondence envelopes. Amendment 2
Relatedness :National : REV/AMD STN 88 5420
** End of Subsector **
Subsector A99: UNDETERMINED.
Subsector : A99 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 0910O820/0001 Published StandardICS : 91.100.50, 93.080.20National Ref : E0910O820Title : Bitumen and bituminous binders - Paving grade bitumen mainly used in ItalyScope : The Technical Report provides a guide line with the complementary information on the
grade selection for the Italian market, according to the UNI EN 12591:2009.
Relatedness :National : New
Subsector : A99 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 0910O830/0001 Project EstablishedICS : 91.100.50, 93.080.20
Page 4
National Ref : E0910O830Title : Bitumen and bituminous binders - Guidelines for specifying cationic bituminous
emulsions mainly used in ItalyScope : The Technical Report provides the properties and televant test methods for cationic
bituminous emulsions produced and utilized in Italy, according to the UNI EN 13808:2005.
Relatedness :National : New
Subsector : A99 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 17030830/0001 Project EstablishedICS : 03.080.30National Ref : E17030830Title : Services - Residential service for elder people - Service requirementsScope : The standards describes service requirements for elder people.
Relatedness :National : REV/AMD UNI 10881:2000
Subsector : A99 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 83000750/0001 Project EstablishedICS : 03.080.01, 03.100.30, 03.100.40National Ref : U83000750Title : Management activities in services supply processes - Method of time survey to evaluate
the resources necessary to carry out the processesScope : The document gives a method to detect the processing times in order to allow a correct
estimation of information technology, human and organization resources needed in operational and management activities that compose company processes. This document is applicable to operational activities with a high human content: front-office, back-office, administrative activities, document management. This document is applicable to organizations working in services area, e.g. banks, insurances, logistics, post, utilities (telecommunications, energy, gas, water supply), public administration. It is mainly applicable to organizations working in: Planning, Organization, Operational management.
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 5
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector B : BUILDING AND CONSTRUCTION
Register issued on : 2010-06-04
Page 6Subsector B01: FIRE PROTECTION.
Subsector : B01 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023281/0001 Project EstablishedICS : 13.220.20, 13.320National Ref : ÖNORM F 3051Title : Fire detection and fire alarm systems - Interpretation unit for alarm transmission
systems Scope : This ÖNORM defines requirements for the interpretation unit for alarm transmission
systems.
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 03100747/0001 Project EstablishedICS :National Ref : 03100747Title : Smoke alarm devices for use in residential buildings, apartments and rooms with similar
purposes - Installation, use and maintenance
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-11Organization : NENCountry : NetherlandsProject ID : 50001562/0001 Project EstablishedICS : 13.220.50National Ref : NEN 6075:2010 Concept nlTitle : Determination of the resistance to smoke movement between spacesScope : Determination of the resistance to smoke movement of partitions. Application: all partition
walls
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 70001412/0001 Project EstablishedICS : 13.220.20, 23.120National Ref : U70001412Title : Smoke and heat control systems - Part 2: Design, installation and maintenance for
powered smoke and heat exhaust ventilatorsScope : This standard gives the criteria for design, installation and maintenance for powered Smoke
and Heat Exhaust Ventilation Systems (SEFFC) in case of fire.
Relatedness :National : REV/AMD UNI 9494:2007
Page 7
Subsector : B01 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 70001520/0001 Project EstablishedICS : 13.220.20National Ref : U70001520Title : Pumpset for fire fighting systems - Additional provision for the application of EN 12845Scope : This technical report specifies additional provision for the application of EN 12845, with
regard to: water supply (clause 9 of EN 12845); pumps (clause 10 of EN 12845).
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 70001530/0001 Project EstablishedICS : 13.220.20National Ref : U70001530Title : Piping systems - Additional provision for the application of EN 12845Scope : This technical report specifies additional provision for the application of EN 12845, with
regard to the characteristics of piping system to be used.
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168532/0001 Project EstablishedICS :National Ref : PR NF S61-937-9Title : Fire safety systems - Operated safety devices - Part 9: Relay boxe for smoke control fan
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168534/0001 Project EstablishedICS :National Ref : PR NF S61-932Title : Fire Safety Systems (FFS) - Installation rules for the fire protection systems
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-25
Page 8
Organization : AFNORCountry : FranceProject ID : FA168535/0001 Project EstablishedICS :National Ref : PR NF S61-970Title : Installation rules for fire detection systems
Relatedness :National : New
Subsector : B01 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035645/0001 Project EstablishedICS :National Ref : PNE 23091Title : Non-percolating lay flat delivery hoses and hose assemblies for fire fighting purposes.Scope : This standard specifies requirements for four-layer non-percolating lay flat delivery hoses
for fire fighting purposes, which are intended for use with fire hose dark hard-coated Barcelona type couplings already fitted.
Relatedness :
National :REV/AMD UNE 23091-1:1989, UNE 23091-2A:1996, UNE 23091-2B:1981, UNE 23091-4:1990, UNE 23091-4/1M:1994, UNE 23091-4/2M:1996
** End of Subsector **
Subsector B02: STRUCTURES.
Subsector : B02 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01000860/0001 Project EstablishedICS :National Ref : BS 6164Title : Code of practice for safety in tunnelling in the construction industry
Relatedness :National : New
** End of Subsector **
Subsector B03: CONCRETE.
Subsector : B03 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023279/0001 Project EstablishedICS : 91.010.30, 91.080.40National Ref : ÖNORM B 4704Title : Execution of concrete structures - National specifications to ÖNORM EN 13670Scope : This ÖNORM has to be used togehter with ÖNORM EN 13670 only. The requirements of
this ÖNORM are necessary for all execution of concrete structures, except production in the factory.
Page 9
Relatedness :National : New
Subsector : B03 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 00515285/0001 Project EstablishedICS :National Ref : 00515285Title : Sealing of joints in concrete with waterstops
Relatedness :National : New
** End of Subsector **
Subsector B10: TIMBER STRUCTURES.
Subsector : B10 Registration Date : 2010-05-19Organization : PKNCountry : PolandProject ID : 00215142/0001 Project EstablishedICS : 79.040National Ref : prPN-D-94021Title : Visual strenght graded coniferous sawn timber for structural useScope : The standard specifies the requirements for visual graded structural coniferus sawn timber.
The document specifies the permissible limits of characteristics for three visual strenght grades of coniferous sawn timber graded by changed method which is in accordance with the recommendations stated in EN 14081-1
Relatedness :National : New
Subsector : B10 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 40005583/0001 Project EstablishedICS : 79.040National Ref : U40005583Title : Structural timber - Visual strength grading for structural timbers - Part 3: Timber Uso
Fiume and Uso TriesteScope : The standard specifies terminology, methods to determine the relevant characteristics and
rules for visual strength grading for structural timbers for use in structures of any size and humidity, due to the definition of Uso Fiume and Uso Trieste.
Relatedness :National : New
** End of Subsector **
Subsector B12: MASONRY.
Subsector : B12 Registration Date : 2010-05-12
Page 10
Organization : DINCountry : GermanyProject ID : 00515096/0001 Project EstablishedICS :National Ref : 00515096Title : Plastering/rendering and plastering/rendering systems - Execution
Relatedness :National : New
Subsector : B12 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035595/0001 Project EstablishedICS :National Ref : PNE 22202-4Title : Natural stone products. Construction of floor with natural stone. Part 4: Raised access
floors.Scope : This standard specifies the procedures for the construction of raised access floors with
natural stone.
Relatedness :National : New
** End of Subsector **
Subsector B14: GEOTECHNICS.
Subsector : B14 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 00515316/0001 Project EstablishedICS :National Ref : 00515316Title : Earthworks and foundations - Soil classification for civil engineering purposes
Relatedness :National : New
Subsector : B14 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035628/0001 Project EstablishedICS :National Ref : PNE 103900Title : In situ determination of moisture content and density of soil and soil aggregate by
granular materials by radioactive methods. Method A: Depth up to 30 cm.Scope : This standard provides a guide for the procedure to follow and precautions to take into
consideration in the in situ determination of the moisture content and density of soils using radioactive methods.
Relatedness :National : New
Page 11** End of Subsector **
Subsector B17: LIGHTING EQUIPMENT AND LIGHTING APPLICATION TECHNOLOGY.
Subsector : B17 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001262/0001 Project EstablishedICS :National Ref : BS 5266-1Title : Emergency lighting. Part 1. Code of practice for the emergency lighting of premises
Relatedness :National : New
Subsector : B17 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 29000420/0001 Project EstablishedICS : 93.080.40National Ref : U29000420Title : Road lighting - Selection of lighting classesScope : This standard determines the lighting classes necessary to apply the performance
requirements of UNI EN 13201-2 for assuring lighting conditions suited for traffic safety and gives recommendations to obtain energy saving and to optimize lighting plants and as regards reduction of environmental impact.
Relatedness :National : REV/AMD UNI 11248:2007
Subsector : B17 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 29000430/0001 Project EstablishedICS : 93.080.40National Ref : U29000430Title : Light and lighting - Use of luminous flux controllers in road lightingScope : This standard gives information for using luminous flux controllers in road lighting systems
when the UNI EN 13201-2 lighting classes are adopted and it describes methods to verify the energy saving their use can produce. The standard defines: parameters to characterize limits and operating conditions of luminaires, when supplied with a luminous flux controller; performance parameters of luminous flux controllers useful to define their conditions in road lighting applications; typical control cycles to evaluate, during the design of a lighting system, the obtainable energy saving if a luminous flux controller is installed. For every parameter the standard gives conditions for its measurement. The standard does not give information about the quality of a device or of a product technology or on pro and contra of a specify control strategy for a given application. This standard can be applied on new lighting systems or, with specific remarks, on existing lighting systems when luminous flux controllers are installed.
Relatedness :National : New
** End of Subsector **
Page 12Subsector B20: DRAINAGE EQUIPMENT.
Subsector : B20 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001020/0001 Project EstablishedICS :National Ref : BS 5502-31:1995+A1Title : Buildings and structures for agriculture. Part 31. Guide to the storage and handling of
waste. Amendment
Relatedness :National : New
Subsector : B20 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001021/0001 Project EstablishedICS :National Ref : BS 5502-50:1993+A1Title : Buildings and structures for agriculture. Part 50. Code of practice for the design,
construction and use of storage tanks and reception pits for livestock slurry. Amendment
Relatedness :National : New
** End of Subsector **
Subsector B21: BATHS.
Subsector : B21 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023291/0001 Project EstablishedICS : 91.010.30, 97.220.10National Ref : ONR 191160Title : Moveable swimming pool covers - Requirements for safetyScope : These ONR contains regulations for the calculation and minimum requirements for the
construction of not commercially used movable swimming pool covers.
Relatedness :National : New
** End of Subsector **
Subsector B25: GAS DISTRIBUTION INSTALLATION AND RELATED EQUIPMENT.
Subsector : B25 (Secondary Subsector)
Registration Date : 2010-05-13
Organization : LVS Draft Issue Date : 2010-05-13Country : Latvia Latest Date for Comments : 2010-06-30Project ID : 00001021/0001 Draft for public enquiryICS : 23.040.01, 91.140.40National Ref : prLVS 419Title : Internal gas pipelines. Installation
Page 13
Scope : The standard defines regulations of design, installation, testing and commissioning of internal pipeline systems for natural gas in buildings of different use with maximal operation pressure 4 bar (including)
Relatedness :National : REV/AMD LVS 419
Subsector : B25 (Secondary Subsector)
Registration Date : 2010-05-13
Organization : LVS Draft Issue Date : 2010-05-13Country : Latvia Latest Date for Comments : 2010-06-30Project ID : 00001022/0001 Draft for public enquiryICS : 91.140.40, 91.140.40National Ref : prLVS 420Title : Gas appliances. Conditions for installation of gas appliancesScope : The standard defines installation requirements of natural gas appliances in buildings of
different use with maximal operation pressure 4 bar (including)
Relatedness :National : REV/AMD LVS 420
** End of Subsector **
Subsector B26: ROAD BUILDING AND MAINTENANCE.
Subsector : B26 Registration Date : 2010-05-10Organization : SNV Draft Issue Date : 2010-05-07Country : Switzerland Latest Date for Comments : 2010-06-09Project ID : CH100011/0001 Draft for public enquiryICS : 93.080.20National Ref : SN 640456Title : Waterproofing and bituminous coatings on pavement surfaces, determination of the
local total thickness
Relatedness :National : New
Subsector : B26 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168311/0001 Project EstablishedICS :National Ref : PR NF P84-706Title : Geosynthetic clay liners - Determination of the flow of liquid or gaz of by overlap length
unit
Relatedness :National : REV/AMD XP P84-706:200208 (P84-706)
** End of Subsector **
Subsector B28: FLOOR COVERINGS.
Subsector : B28 Registration Date : 2010-05-20
Page 14
Organization : UNICountry : ItalyProject ID : 87035130/0001 Project EstablishedICS : 91.060.30National Ref : U87035130Title : Resilient and laminate floor coverings - Instructions for the design, installation and
maintenanceScope : The standard gives instructions for the design, installation and maintenance of resilient and
laminate floor coverings.
Relatedness :National : New
** End of Subsector **
Subsector B29: AGGREGATES.
Subsector : B29 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168484/0001 Project EstablishedICS :National Ref : PR NF X46-040Title : Radon handling in buildings - Referential for technical dignosis relating to the presence
of radon in buildings - Mission and methodology
Relatedness :National : New
** End of Subsector **
Subsector B30: FLOOR AND SURFACING .
Subsector : B30 Registration Date : 2010-05-13Organization : UNI Draft Issue Date : 2010-04-07Country : Italy Latest Date for Comments : 2010-06-06Project ID : 87035140/0001 Draft for public enquiryICS : 91.100.10National Ref : U87035140Title : Wood and parquet flooring screeds - Properties and performance characteristicsScope : This standard defines properties and performance characteristics of cementitious or special
binders based floor screeds and calcium sulphate screeds, to be used for installation with adhesives of wood and parquet flooring. This standard applies to new screed and repair of existing screeds.
Relatedness :National : New
** End of Subsector **
Subsector B31: HEATING SYSTEMS IN BUILDINGS.
Subsector : B31 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023284/0001 Project Established
Page 15
ICS : 01.110, 35.240.10, 91.140.01National Ref : ÖNORM H 6010-2Title : Documents used in building technology - Part 2: Graphic symbols and abbreviated
terms for CAD applicationsScope : The symbols, code letters and identification colours defined in this Austrian Standard are to
be used for the essential construction elements in diagrams of technical building equipment. In representations to scale, only the code letters and identification colours and, as far as useful and necessary, also the symbols listed in this ÖNORM should be used. The symbols are suitable for CAD applications and stored in a dxf block library.
Relatedness :National : New
Subsector : B31 Registration Date : 2010-05-18Organization : UNICountry : ItalyProject ID : 0208C080/0001 Project EstablishedICS : 17.200.10, 91.140.10National Ref : E0208C080Title : Heat costs allocation based on heat unit shut-off valves and insertion time counterScope : This technical report provides the requirements regarding the use of the heat costs
allocation systems based on heat shut-off valves and insertion times counter.
Relatedness :National : New
** End of Subsector **
Subsector B32: PRECAST CONCRETE PRODUCTS.
Subsector : B32 Registration Date : 2010-05-18Organization : SISTCountry : Slovenia Latest Date for Comments : 2010-07-01Project ID : 00005245/0003 Project EstablishedICS : 91.080.40National Ref : SIST EN 13670:2010/oA101:2010Title : Execution of concrete structures
Relatedness :National : New
Subsector : B32 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 00515070/0001 Project EstablishedICS :National Ref : 00515070Title : Precast concrete products - Road traffic noise reducing devices and barriers -
Requirements and test methods
Relatedness :National : New
** End of Subsector **
Page 16Subsector B99: UNDETERMINED.
Subsector : B99 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01000859/0001 Project EstablishedICS :National Ref : BS 8544Title : Guide on life cycle costing during the in-use phase
Relatedness :National : New
Subsector : B99 Registration Date : 2010-05-11Organization : NENCountry : NetherlandsProject ID : 50001563/0001 Project EstablishedICS : 91.040.99National Ref : NTA 8111:2010 nlTitle : Floating constructionScope : Requirements, conditions etc. for floating and amphibious, especially immovable buildings
Relatedness :National : New
Subsector : B99 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 71031460/0001 Project EstablishedICS : 93.010National Ref : U71031460Title : Rockfall protective measures - Tests on meshes for slopes coverageScope : The standard defines procedures for the determination of the main properties of meshes
used for slopes coverage.
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 17
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector C : CHEMICALS, CHEMICAL ENGINEERING AND FOOD PRODUCTS
Register issued on : 2010-06-04
Page 18Subsector C01: Food products
Subsector : C01 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 05701433/0001 Project EstablishedICS :National Ref : 05701433Title : Food hygiene - Containers for liquid, granulated and powdered foodstuffs - Part 6:
Cleaning and disinfection
Relatedness :National : New
Subsector : C01 Registration Date : 2010-05-17Organization : UNMZ Draft Issue Date : 2010-08-31Country : Czech Republic Latest Date for Comments : 2010-10-30Project ID : 46001010/0001 Published StandardICS :National Ref :Title : Potatoes – Potatoes for consumption, lateScope : This standard specifies the characteristics of potato late ware. These properties are to meet
all the varieties and hybrids of potato (Solanum tuberosum L.), in its natural state for human consumption, the supply and / or after their preparation and packaging for the final consumer. Not for ware potatoes, potatoes for industrial, feed and potatoes for seed potatoes.
Relatedness :National : REV/AMD CSN 46 2200-4:1996
Subsector : C01 Registration Date : 2010-05-17Organization : UNMZ Draft Issue Date : 2010-08-31Country : Czech Republic Latest Date for Comments : 2010-10-30Project ID : 46001110/0001 Published StandardICS :National Ref :Title : Potatoes – Potatoes for consumption, earlyScope : This standard specifies the characteristics of early potatoes for consumption. These
properties are to meet all the varieties and hybrids of potato (Solanum tuberosum L.), in its natural state for human consumption, the supply and / or after their preparation and packaging for the final consumer. Not for ware potatoes, potatoes for industrial, feed and potatoes for seed potatoes.
Relatedness :National : REV/AMD CSN 46 2200-3:1996
Subsector : C01 Registration Date : 2010-05-17Organization : UNMZ Draft Issue Date : 2010-08-31Country : Czech Republic Latest Date for Comments : 2010-10-30Project ID : 56001010/0001 Published StandardICS :National Ref :Title : Testing methods for malt and malt extracts – Part 1: Testing of malt
Page 19
Scope : Control methods malt and specialty malts, malt substitutes listed in this standard are used to establish the basic technology of substances, which influence the course of manufacture of malt or beer and contribute to analytical and organoleptic characteristics of products.
Relatedness :National : REV/AMD CSN 56 0187:1967
Subsector : C01 Registration Date : 2010-05-17Organization : UNMZ Draft Issue Date : 2010-08-31Country : Czech Republic Latest Date for Comments : 2010-10-30Project ID : 56001110/0001 Published StandardICS :National Ref :Title : Testing methods for beer – Part 12: Determination of proteinScope : Nitrogen compounds in the malt used depends on the quality of barley, respectively.
protein content. In addition to determining the total malt protein (or protein) is an important value of soluble nitrogen compounds, which will go into solution at mashing. Their value points to measure proteolytic cleavage of high nitrogen compounds during malting. Quantity and quality of soluble nitrogen compounds is of great importance in the technology affects the quality of beer.
Relatedness :National : REV/AMD CSN 56 0186-12:1981
Subsector : C01 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 59107610/0001 Project EstablishedICS : 67.120.10National Ref : U59107610Title : Meat and meat products - Determination of total ashScope : This standard specifies a method for the determination of the total ash from all kinds of
meat and meat products, including poultry.
Relatedness :National : REV/AMD UNI 10590:1997
** End of Subsector **
Subsector C02: PAINTS AND RELATED PRODUCTS.
Subsector : C02 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035406/0001 Project EstablishedICS :National Ref : PNE 48314Title : Paints and varnishes. Soiling resistance after weathering.Scope : This standard specifies a test method for to assess the degree of soiling resistance of
coating films to withstand soiling agents after weathering. It is meanly applicable to water-base coatings for external masonry.
Relatedness :
Page 20
National : New
** End of Subsector **
Subsector C03: CHEMISTRY.
Subsector : C03 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 0209C071/0001 Project EstablishedICS : 75.160.10National Ref : E0209C071Title : Non mineral refuse derived fuels - Part 1: Specification, classes, terms and definitionsScope : This standard specifies the classification, the physico-chemical properties of the refuse
derived fuels and the general requirements for the storage, handling and transport. This standard also provides general definitions regarding the most common terms used in technical legislation on non-mineral refuse derived fuels.
Relatedness :National : REV/AMD UNI 9903-1:2004; UNI 9903-2:2004
** End of Subsector **
Subsector C11: TOBACCO.
Subsector : C11 Registration Date : 2010-05-27Organization : AENORCountry : Spain Latest Date for Comments : 2010-06-16Project ID : P0035340/0002 Draft for public enquiryICS :National Ref : PNE 118010Title : Cigarettes. Determination of nicotine retained by filters. Analytical method by gas
chromatography.Scope : This UNE standard specifies a chromatographic method for the determination of the
nicotine retained by filters en cigarettes.
Relatedness :National : REV/AMD UNE 118010:2005 EX
** End of Subsector **
Subsector C13: FERTILIZERS.
Subsector : C13 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023287/0001 Project EstablishedICS :National Ref : ÖNORM S 2207-1Title : Technical requirements for fermentation plants - Part 1: Definitions and principlesScope : The aim of this ÖNORM is to define the framework for planning, approval, construction and
proper operation of fermentation plants under consideration of the quality of the gasseous, liquid or solid end products. This ÖNORM includes the definitions and principles of fermentation plants for the anaerobe recovery and treatment of bio-degradable agriculturale, industrial and community waste. It applies also for fermentation plants in
Page 21
Scope : terms of eco-power law. Considerations are given to environmentally relevant in-plant and the environment of the fermentation plant concerning emissions and imissions.
Relatedness :National : New
Subsector : C13 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023288/0001 Project EstablishedICS :National Ref : ÖNORM S 2207-2Title : Technical requirements for fermentation plants - Part 2: Requirements for industrial
process engineeringScope : The aim of this ÖNORM is to define the framework for planning, approval, construction and
proper operation of fermentation plants under consideration of the quality of the gasseous, liquid or solid end products. This ÖNORM specifies the minimum requirements for fermentation plants for the anaerobe recovery and treatment of bio-degradable agriculturale, industrial and community waste. It applies also for fermentation plants in terms of eco-power law. Considerations are given to environmentally relevant in-plant and the environment of the fermentation plant concerning emissions and imissions.
Relatedness :National : New
Subsector : C13 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168494/0001 Project EstablishedICS :National Ref : NF U44-051/A2Title : Organic soils improvers - Designations, specifications, marking
Relatedness :National : New
Subsector : C13 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168495/0001 Project EstablishedICS :National Ref : NF U44-095/A2Title : Organic soil improvers - Composts containing substances essential to agricultural,
stanning from water treatment
Relatedness :National : New
Page 22
Subsector : C13 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168587/0001 Project EstablishedICS :National Ref : PR NF U47-035Title : Animal health analysis methods - Detection of antibodies against classical swine fever
by virus neutralisation test and immonochemistry on cell cultures (IF or IP)
Relatedness :National : New
** End of Subsector **
Subsector C17: TREES AND PLANTS.
Subsector : C17 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001092/0001 Project EstablishedICS :National Ref : BS 8545Title : Code of practice for trees. From nursery to independence in the landscape
Relatedness :National : New
** End of Subsector **
Subsector C19: CHEMICAL ANALYSIS
Subsector : C19 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233472/0001 Project EstablishedICS :National Ref : 06233472Title : pH measurement - Reference buffer solutions for the calibration of pH measuring
equipment
Relatedness :National : New
** End of Subsector **
Subsector C99: UNDETERMINED.
Subsector : C99 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 05500120/0001 Project EstablishedICS :National Ref : 05500120Title : Laboratory furniture - Fume cupboards - Part 4: Fume cupboards for dispensaries
Relatedness :
Information procedure Page 24
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector F : FUNDAMENTAL STANDARDS
Register issued on : 2010-06-04
Page 25Subsector F05: MEASURING INSTRUMENTS.
Subsector : F05 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001085/0001 Project EstablishedICS :National Ref : BS 7843-1Title : Meteorological precipitation. Part 1. Rainfall intensity gauge instrumentation
Relatedness :National : New
Subsector : F05 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001086/0001 Project EstablishedICS :National Ref : BS 7843-2Title : Meteorological precipitation. Part 2. User requirements for precipitation data
Relatedness :National : New
Subsector : F05 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001087/0001 Project EstablishedICS :National Ref : BS 7843-3Title : Meteorological precipitation. Part 3. Storage and rainfall intensity gauge instrumentation
Relatedness :National : New
Subsector : F05 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001088/0001 Project EstablishedICS :National Ref : BS 7843-4Title : BS 7843-4 Meteorological precipitation. Part 4. Operational requirements
Relatedness :National : New
** End of Subsector **
Subsector F07: DOCUMENTATION AND INFORMATION
Subsector : F07 Registration Date : 2010-05-12Organization : ASICountry : Austria
Page 26
Project ID : 00023277/0001 Project EstablishedICS : 37.080National Ref : ÖNORM A 1306Title : Computer Output on Microfilm (COM) - Microfiche A6 - Dimensions, structure, reduction
ratiosScope : This ÖNORM specifies A6 format microfiches of the first generation showing the reduction
ratios VA = 1/24, VA = 1/42 and VA = 1/48, prepared according to ÖNORM A 1305. Aberrant from ISO 9923, this ÖNORM also covers the reduction ratio VA = 1/42 predominantly used in Austria. It applies neither to COM outputs on 16 mm or 35 mm roll films nor to the COM output of graphical presentations (drawings). The microfiches may optionally have negative or positive polarity.
Relatedness :National : New
Subsector : F07 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023278/0001 Project EstablishedICS : 37.080National Ref : ÖNORM A 1307Title : Microfiche A6 - General requirements, structureScope : This ÖNORM specifies the general requirements for A6 format microfiches of the first
generation. The specifications allow free structuring of the information fields of microfiches and their flawless use on all readers and readers-photocopiers, irrespective of the size of the master copies, permitting optimal utilization of the information field. This ÖNORM does not apply to COM outputs on microfiches as defined by ÖNORM A 1306.
Relatedness :National : New
** End of Subsector **
Subsector F14: GRAPHICAL TECHNOLOGY, SIGN-BOARDS AND NAMEPLATES.
Subsector : F14 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023275/0001 Project EstablishedICS : 01.140.40, 35.240.30, 37.100.01National Ref : ÖNORM A 1505-1Title : Data preparation and criteria for quality in offset printing - Part 1: Process oriented data
processingScope : This Austrian Standard (ÖNORM) serves as a guideline for the process adjusted preparation
of PDF-data for sheet fad and web fad offset printing according to ISO 12647-2 which are delivering comparable printing results in all offset printing plants.
Relatedness :National : New
Subsector : F14 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023276/0001 Project Established
Page 27
ICS : 01.140.40, 35.240.30, 37.100.01National Ref : ÖNORM A 1505-2Title : Data preparation and criteria for quality in offset printing - Part 2: Media-independent
data processingScope : This Austrian Standard (ÖNORM) serves as a guideline for the media-independant
preparation of PDF-data for sheet fad and web fad offset printing according to ISO 12647-2 which are delivering comparable printing results in all austrian offset printing plants.
Relatedness :National : New
** End of Subsector **
Subsector F16: GRAPHICAL SYMBOLS.
Subsector : F16 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168489/0001 Project EstablishedICS :National Ref : PR NF X08-011Title : Colours. White and colour standards by reflexion.
Relatedness :National : New
** End of Subsector **
Subsector F19: OPTICS.
Subsector : F19 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023285/0001 Project EstablishedICS : 03.080.30, 03.180, 13.280, 31.260National Ref : ÖNORM S 1100-1Title : Laser safety officer - Part 1: Responsibilities and competencesScope : This ÖNORM complements the provisions on laser safety presented in ÖVE/ÖNORM EN
60825 (all parts) by determining the procedures for preventive measures and for managing laser accidents and by defining the competence of those, who are working with laser equipment and responsible for laser safety, especially of the laser safety officer. The recommendations provided by CLC/TR 50448 are considered. This ÖNORM supports organizations operating laser equipments by providing an organizational structure for the implementation and maintenance of effective monitoring procedures stipulated eg in ÖVE/ÖNORM EN 60825-1. Furthermore is has to be ensured, that persons using, or testing laser equipment and are responsible for laser safety have the necessary know-how, understanding and opportunity to perform their task without exposing themselves or other to unnecessary health risks. This ÖNORM determines the responsibility of the employer in respect to laser safety, set up a system of safety measures to fulfill the requirements on organizations using laser equipment and defines the minimum requirements on the qualification.
Relatedness :National : New
Page 28
Subsector : F19 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023286/0001 Project EstablishedICS : 03.080.30, 03.180, 13.280, 31.260National Ref : ÖNORM S 1100-2Title : Laser safety officer - Part 2: Requirements on trainingScope : This ÖNORM defines the requirements on the training of laser safety officers. With the
training as proved laser safety officer according to this ÖNORM the person is qualified to evaluate and to control laser threats in certain types of laser application and to be responsible for the monitoring of safety measures.
Relatedness :National : New
** End of Subsector **
Subsector F21: VALUE ANALYSIS AND PROJECT NETWORK.
Subsector : F21 Registration Date : 2010-05-19Organization : EVSCountry : EstoniaProject ID : 00095629/0001 Project EstablishedICS : 03.060, 91.040National Ref : prEVS 875-1Title : Property valuation - Part 1: Valuation Concepts and PrinciplesScope : This standard provides the main and general principles of valuation theory and practice.
Relatedness :National : REV/AMD EVS 875-1:2005
Subsector : F21 Registration Date : 2010-05-19Organization : EVSCountry : EstoniaProject ID : 00095630/0001 Project EstablishedICS : 03.060, 91.040National Ref : prEVS 875-2Title : Property valuation - Part 2: Types of PropertiesScope : The current standard provides valuers with the guidance as real property has to be
distinguished from other types of assets. The standard also provides systematic approach what are the property types under the Estonian regulation.
Relatedness :National : REV/AMD EVS 875-2:2005
Subsector : F21 Registration Date : 2010-05-19Organization : EVSCountry : EstoniaProject ID : 00095631/0001 Project EstablishedICS : 03.060, 91.040National Ref : prEVS 875-3Title : Property valuation - Part 3: Valuation Bases
Page 29
Scope : The current standard provide extensive understanding of market value definition along with IVS. The standard also provides other value types used in valuation and provides rules when and how these should be implemented.
Relatedness :National : REV/AMD EVS 875-3:2005
Subsector : F21 Registration Date : 2010-05-19Organization : EVSCountry : EstoniaProject ID : 00095632/0001 Project EstablishedICS : 03.060, 91.040National Ref : prEVS 875-4Title : Property valuation - Part 4: Code of Conduct and Valuation – ReportingScope : The standard provides the important Ethical rules and code of conduct what valuers have to
follow. The standard also provides reporting rules for valuation reporting.
Relatedness :National : REV/AMD EVS 875-4:2005
Subsector : F21 Registration Date : 2010-05-19Organization : EVSCountry : EstoniaProject ID : 00095633/0001 Project EstablishedICS : 03.060, 91.040National Ref : prEVS 875-5Title : Property valuation - Part 5: Valuation for Financial ReportingScope : The standard provides the guidance related to the valuation for financial statements,
terminology used by valuation and in financial statements. The standard provides the guidance how valuers should implement different value base.
Relatedness :National : REV/AMD EVS 875-5:2005
** End of Subsector **
** End of Sector **
Information procedure Page 30
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector H : PRODUCTS FOR HOUSEHOLD AND LEISURE USE
Register issued on : 2010-06-04
Page 31Subsector H04: SPORTS EQUIPMENT.
Subsector : H04 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001112/0001 Project EstablishedICS :National Ref : BS 6366Title : Replaceable studs for rugby football boots
Relatedness :National : New
Subsector : H04 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 61002600/0001 Project EstablishedICS : 97.200.40National Ref : U61002600Title : Guidelines for the design of outdoor and play outdoor areasScope : This standard specifies requirements and instruction for the planning of playgrounds and
play areas for children and young children covered by UNI EN 748, UNI EN 749, UNI EN 1176, UNI EN 1177, UNI EN 1270, UNI EN 1271, UNI EN 12572.
Relatedness :National : REV/AMD UNI 11123:2004
** End of Subsector **
Subsector H07: SPACE HEATING.
Subsector : H07 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01000855/0001 Project EstablishedICS :National Ref : BS 6896Title : Specification for installation of gas-fired overhead radiant heaters for industrial and
commercial heating (2nd and 3rd family gases)
Relatedness :National : New
** End of Subsector **
Subsector H09: FURNITURE.
Subsector : H09 Registration Date : 2010-05-04Organization : BSICountry : United KingdomProject ID : 01001115/0001 Project EstablishedICS :National Ref : BS 8509:2008+A1Title : Children's beds for domestic use. Safety requirements and test methods. Amendment
Page 32
Relatedness :National : New
Subsector : H09 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0030613/0001 Project EstablishedICS :National Ref : PNE 89401-4Title : Office furniture. Materials for office furniture. Part 4: ScreensScope : This standard specifies requirements for materials for screens of office furniture depending
on the use. It does not limit the materials used, the furniture design or the final user intended.
Relatedness :National : New
** End of Subsector **
Subsector H29: HEAT PUMPS.
Subsector : H29 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 0206C020/0001 Project EstablishedICS : 27.080National Ref : E0206C020Title : Heat pump geothermal systems - Design and sizing requirementsScope : This standard sets design and sizing criteria and calculus procedures for the determination
of both design and periodic performances of heat pump geothermal systems. This standard allows to determine the contribution of renewable energies provided by geothermal heat pump for the energetic certification of buildings. This standard applies to both heat pump geothermal systems and direct exchange for heating, cooling, climing and sanitary hot water production by heat exchange with soil.
Relatedness :National : New
Subsector : H29 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 0206C030/0001 Project EstablishedICS : 27.080National Ref : E0206C030Title : Heat pump geothermal systems - Installation requirementsScope : This standard sets perforation methods, geodrills fabrication procedures, geothermic
response tests procedures, requirements for both heat pump and implant devices choice, installation and function limits; characteristics of geoexchange and perforation fluids, filling and geoexchange materials; devices, tools, equipment for geodrills and geothermic response; drafting of documents and reports. This standard applies to both heat pump geothermal systems and direct exchange for heating, cooling, climing and sanitary hot water production by heat exchange with soil.
Page 33
Relatedness :National : New
Subsector : H29 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 0206C170/0001 Project EstablishedICS : 27.080National Ref : E0206C170Title : Heat pump geothermal systems - Environmental requirementsScope : This standard sets a validation procedure for the environmental compatibility level of heat
pump geothermal implants. This standard applies to heat pump geothermal implants for heating, cooling, climing and sanitary hot water production by heat exchange with the geothermic source. This standard applies to any kind of implants.
Relatedness :National : New
** End of Subsector **
Subsector H30: EQUIPMENT FOR CHILDREN.
Subsector : H30 (Secondary Subsector)
Registration Date : 2010-05-04
Organization : BSICountry : United KingdomProject ID : 01001115/0001 Project EstablishedICS :National Ref : BS 8509:2008+A1Title : Children's beds for domestic use. Safety requirements and test methods. Amendment
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 34
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector I : MECHANICAL ENGINEERING
Register issued on : 2010-06-04
Page 35Subsector I02: FASTENERS.
Subsector : I02 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06701808/0001 Project EstablishedICS :National Ref : 06701808Title : Spring retaining rings with lugs for use in bores (internal circlips)
Relatedness :National : New
** End of Subsector **
Subsector I06: PRESSURE VESSELS.
Subsector : I06 Registration Date : 2010-05-13Organization : LVS Draft Issue Date : 2010-05-13Country : Latvia Latest Date for Comments : 2010-06-13Project ID : 00006006/0001 Draft for public enquiryICS : 23.020.30, 23.020.30National Ref : prLVS 415Title : Assemblies of pressure equipment. Safety examination of existing assemblies Scope : The standard defines the order of technical checks of assemblies of pressure equipment
with purpose to define, estimate risk factors and their factors of influence to the further using. The standard concerns on the inspection organizations which according to statutory acts of Republic of Latvia perform technical checks of assemblies of pressure equipment.
Relatedness :National : REV/AMD LVS 415
Subsector : I06 Registration Date : 2010-05-14Organization : LVS Draft Issue Date : 2010-05-14Country : Latvia Latest Date for Comments : 2010-06-13Project ID : 00006007/0002 Draft for public enquiryICS : 23.020.10National Ref : prLVS 350Title : Tanks. Technical examination of existing tanksScope : The purpose of this standard is to establish and assess risk factors and its influence to new
and used tanks safety usage. Results of assessment registered in protocol (annex A). This standard defines requirements applies to tanks classified in chapter 4. This document is not applicable for isothermic tanks with coating for liquefied substances storage in low temperatures
Relatedness :National : REV/AMD LVS 350
Subsector : I06 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 0203B445/0001 Project EstablishedICS : 23.020.30, 27.060.30National Ref : E0203B445
Page 36
Title : Pressure equipment - Putting into service and use of pressure equipment and assemblies - Part 5: Repair and modification
Scope : The standard provides procedures and technical reference for repair and modification of pressure equipment and assemblies.
Relatedness :National : New
Subsector : I06 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 0203B447/0001 Project EstablishedICS : 23.020.30, 27.060.30National Ref : E0203B447Title : Pressure equipment - Putting into service and use of pressure equipment and
assemblies - Part 7: ExceptionsScope : The standard specifies cases not applicable with regard to D.M.329/2004.
Relatedness :National : New
** End of Subsector **
Subsector I17: MACHINERY IN GENERAL (INCLUDING SAFETY)
Subsector : I17 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06002661/0001 Project EstablishedICS :National Ref : 06002661Title : Milk processing machinery and plant - Part 1: Terms and definitons
Relatedness :National : New
Subsector : I17 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06002662/0001 Project EstablishedICS :National Ref : 06002662Title : Milk processing machinery and plant - Part 2: Planning and acceptance
Relatedness :National : New
Subsector : I17 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06002663/0001 Project EstablishedICS :National Ref : 06002663
Page 37
Title : Milk processing machinery and plant - Part 3: Plant technics
Relatedness :National : New
** End of Subsector **
Subsector I19: NUCLEAR ENERGY.
Subsector : I19 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023289/0001 Project EstablishedICS : 11.040.50, 11.040.60, 17.240National Ref : ÖNORM S 5236-2Title : Recording in medical application of ionizing radiation - Part 2: BrachytherapyScope : This ÖNORM specifies the recording in application of ionizing radiation in brachytherapy,
both the application of afterloading technique and the manual application of emitters.
Relatedness :National : New
Subsector : I19 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023290/0001 Project EstablishedICS : 11.040.50, 35.240.80National Ref : ÖNORM S 5271Title : Planar scintigraphy and single photon emission computed tomography - Constancy
tests of functional performance characteristicsScope : This ÖNORM applies for Anger type gamma cameras (including gamma cameras with
multiple measuring heads) used for planar scintigraphy and/or single photon emission computed tomography (SPECT). This ÖNORM includes requirements on the test devices and software to be used as well as provides guidance for the constancy testing. The purpose of this ÖNORM is to provide simple procedures for the constancy tests to be performed by the user with tools and facilities which are as simple as possible. The precondition for the constancy tests are reference measurements done right after the acceptance test or partial acceptance test. The reference measurements and measurements for constancy tests have to be performed under the same conditions and have to be documented.
Relatedness :National : New
Subsector : I19 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023292/0001 Project EstablishedICS : 11.020, 13.280, 17.240National Ref : ÖNORM S 5275-2Title : Nuclear medical therapy - Criterias for the discharge - Part 2: Calculation method taking
into account complex conditionsScope : For the calculation of the discharge activity of the patient treated with open radioactive
sources and depending on the type of radiation the exposition to environment through external radiation and/or possible radioactive contamination (mainly by air) has to be
Page 38
Scope : considered. For the assessment of radiation exposure to the environment the constant of the ambient dose rate equivalent has to be used as the basis. In this part 2 of the ÖNORM a more complex calculation method is introduced with which more precise discharge activities can be calculated then in ÖNORM S 5275-1. The precondition is the knowledge of further factors, e.g. biokinetics, distribution of the activity in the body, possible contamination of the tidal air. In this ÖNORM only the nuclides 117mSn, 131I, 153Sm, 186Re und 188Re are considered. The reason the limitation to these five nuclides is because the simplified calculation method in part 1 for other nuclides provides maximum permissible discharge activities which are already above the applied activities used in practice. This ÖNORM specifies criteria for the patient discharge after the application of open radioactive sources for therapeutically purposes (e.g. radioiodine therapy, palliative therapy, radiosynoviorthesis) knowing factors, which are not considered in part 1.
Relatedness :National : New
Subsector : I19 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233487/0001 Project EstablishedICS :National Ref : 06233487Title : Terms and definitions of nuclear technology - Part 1: Basic notions of physics and
chemistry
Relatedness :National : New
Subsector : I19 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233488/0001 Project EstablishedICS :National Ref : 06233488Title : Terms and definitions of nuclear technology; Part 2: Reactor design
Relatedness :National : New
Subsector : I19 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233489/0001 Project EstablishedICS :National Ref : 06233489Title : Terms and definitions of nuclear technology; Part 4: Safeguards
Relatedness :National : New
Subsector : I19 Registration Date : 2010-05-12
Page 39
Organization : DINCountry : GermanyProject ID : 06233490/0001 Project EstablishedICS :National Ref : 06233490Title : Terms and definitions of nuclear technology; Part 5: Nuclear fuel technology
Relatedness :National : New
Subsector : I19 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233498/0001 Project EstablishedICS :National Ref : 06233498Title : Terms and definitions of nuclear technology; Part 9: Radioactive waste management
Relatedness :National : New
** End of Subsector **
Subsector I30: AIR DISTRIBUTION.
Subsector : I30 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 0205A037/0001 Project EstablishedICS : 91.140.30National Ref : E0205A037Title : Air-conditioning systems for thermal comfort in buildings - Classification, requirements
and performance requirements for the design and deliveryScope : This standard gives a classification for air conditioning systems, defines the minimum
performance requirements and the reference parameters of the indoor environment. The standard identifies the elements to be specified by the owner in his request for quotation and by the designer and/or contractor in the project and/or supply specifications. This document provides guidance on ventilation, air-conditioning and room-conditioning systems in order to achieve a comfortable and healthy indoor environment with acceptable installation and running costs.
Relatedness :National : REV/AMD UNI 10339:1995
** End of Subsector **
Subsector I31: VALVES.
Subsector : I31 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168418/0001 Project EstablishedICS :National Ref : PR NF E29-573Title : Industrial pipework Express connections Dimensions of connections with maximum
Page 40
Title : allowable pressure 1 MPa (10 bar)
Relatedness :National : REV/AMD NF E29-573:198803 (E29-573)
** End of Subsector **
Subsector I40: INDUSTRIAL PIPING NETWORKS.
Subsector : I40 Registration Date : 2010-05-13Organization : LVS Draft Issue Date : 2010-05-13Country : Latvia Latest Date for Comments : 2010-06-30Project ID : 00001021/0001 Draft for public enquiryICS : 23.040.01, 91.140.40National Ref : prLVS 419Title : Internal gas pipelines. InstallationScope : The standard defines regulations of design, installation, testing and commissioning of
internal pipeline systems for natural gas in buildings of different use with maximal operation pressure 4 bar (including)
Relatedness :National : REV/AMD LVS 419
Subsector : I40 Registration Date : 2010-05-13Organization : LVS Draft Issue Date : 2010-05-13Country : Latvia Latest Date for Comments : 2010-06-30Project ID : 00001022/0001 Draft for public enquiryICS : 91.140.40, 91.140.40National Ref : prLVS 420Title : Gas appliances. Conditions for installation of gas appliancesScope : The standard defines installation requirements of natural gas appliances in buildings of
different use with maximal operation pressure 4 bar (including)
Relatedness :National : REV/AMD LVS 420
** End of Subsector **
** End of Sector **
Information procedure Page 41
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector M : METALLIC MATERIALS
Register issued on : 2010-06-04
Page 42Subsector M01: STEEL.
Subsector : M01 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 16320070/0001 Project EstablishedICS : 23.040.60National Ref : E16320070Title : Ductile iron pipes, fittings and accessories for pressure and gravity pipe-lines -
Automatic flexible joint - Coupling dimensions and joint accessoriesScope : This standard defines the reference dimensions of the elastic automatic joint and of its
accessories able to permit the connection of the joint, for ductile iron pipes and fittings manufactured in compliance with UNI EN 545, UNI EN 598 standards and suitable for the construction of pipelines carrying water for pressure or gravity service.
Relatedness :National : REV/AMD UNI 9163:1987
** End of Subsector **
Subsector M05: WELDING.
Subsector : M05 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 28009360/0001 Project EstablishedICS : 03.080.20, 03.100.30, 25.160.01National Ref : U28009360Title : Coordination of welding, pipe laying and test activities for polyethylene transmission
lines of gaseous fuels, water and other fluids under pressure - Tasks and responsibilities, requirements for training, qualification and certification of personnel
Scope : The standard defines the tasks and responsibilities of personnel responsible for coordination of welding, laying and testing of polyethylene networks for the transmission of gaseous fuels, water and other fluids under pressure and requirements for its training, qualification and certification. The standard also establishes requirements for training centres and the organizational and executive modalities for the courses.
Relatedness :National : REV/AMD UNI 10761:1999
Subsector : M05 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 28009460/0001 Project EstablishedICS : 25.160.30National Ref : U28009460Title : Laboratory welding machines by heated tool by radiation for polyethylene pipes and/or
fittings butt joints for pressure fluids pipelines - Functional characteristics, test and documentation
Scope : This standard specifies functional requirements and modalities to test and maintenance of laboratory welding machines by heated tool by radiation for polyethylene pipes and/or fittings butt joints with equal diameter and SDR for pressure fluids pipelines.
Relatedness :National : New
Page 43** End of Subsector **
Subsector M10: METALLIC COATINGS.
Subsector : M10 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 68002260/0001 Published StandardICS : 25.220.50National Ref : U68002260Title : Vitreous and porcelain enamels - Determination of resistance to chemical corrosion to
neutral liquids and/or their vapoursScope : The standard gives the definition of vitreous and porcelain enamel and makes its
classification according to the support and the final product upon which it will be applied and, in the this last case, of the final usage, in contact with water for human consumption or with food.
Relatedness :National : REV/AMD UNI 6722:1989
** End of Subsector **
Subsector M21: PRECIOUS METALS.
Subsector : M21 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 99000701/0001 Project EstablishedICS : 77.120.99National Ref : U99000701Title : Procedures for chemical analysis of metal - Determination of silver in silver alloys -
Cupellation methodScope : The standard specifies the methods to determine silver in silver alloy.
Relatedness :National : New
** End of Subsector **
Subsector M99: UNDETERMINED.
Subsector : M99 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233496/0001 Project EstablishedICS :National Ref : 06233496Title : Non-destructive testing - Electromagnetic detection - Part 2: Active electro-magnetic
induction methods
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 44
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector N : NON-METALLIC MATERIALS
Register issued on : 2010-06-04
Page 45Subsector N01: PAPER AND BOARD.
Subsector : N01 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 23002300/0001 Project EstablishedICS : 85.060National Ref : U23002300Title : Paper - Determination of Gravure printability - Heliotest methodScope : This standard specifies a test procedure for the determination of the gravure printability of
a paper by means of the Heliotest method. This standard is used for papers to be printed in rotogravure, such as coated and low-weight coated papers or well-calendered papers.
Relatedness :National : New
** End of Subsector **
Subsector N02: SOLID FUELS.
Subsector : N02 Registration Date : 2010-05-18Organization : UNICountry : ItalyProject ID : 0209C090/0001 Project EstablishedICS : 75.160.10National Ref : E0209C090Title : Sustainability criteria of solid biomass for energy applicationsScope : The standard defines indexes for the evaluation, in terms of CO2 savings, of the
sustainability of solid biomass for energy applications. These indexes take into account energetic and environmental issues linked to solid biomass production and processing. The standard provides the method for the sustainability calculation.
Relatedness :National : New
** End of Subsector **
Subsector N03: PETROLEUM PRODUCTS.
Subsector : N03 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233473/0001 Project EstablishedICS :National Ref : 06233473Title : Petroleum products - Determination of the oxidation stability of oils by measuring the
chemiluminescence
Relatedness :National : New
Page 46
Subsector : N03 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233474/0001 Project EstablishedICS :National Ref : 06233474Title : Petroleum products - Determination of the oxidation stability of lubricating greases by
measuring the chemiluminescence
Relatedness :National : New
Subsector : N03 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233481/0001 Project EstablishedICS :National Ref : 06233481Title : Testing of liquid fuels - Determination of the vanadium and nickel content - Part 4:
Determination by atomic absorption spectrometry (AAS) after incineration
Relatedness :National : New
Subsector : N03 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06233491/0001 Project EstablishedICS :National Ref : 06233491Title : Automotive Fuels - Test methods - Part 6: Direct determination of trace elements in
vegetable oils by inductively coupled plasma optical emission spectroscopy (ICP OES)
Relatedness :National : New
** End of Subsector **
Subsector N05: TEXTILES.
Subsector : N05 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168417/0001 Project EstablishedICS :National Ref : PR NF G37-114Title : Coated fabrics with rubber or plastic- Gas permeability test
Relatedness :National : New
** End of Subsector **
Subsector N06: RUBBER.
Page 47
Subsector : N06 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 35007080/0001 Project EstablishedICS : 83.060National Ref : U35007080Title : Rubbers - Tests on raw and vulcanized rubbers - Quantitative analysis -
Thermogravimetric methodScope : This standard specifies two thermogravimetric methods for the determination of raw and
vulcanized rubbers composition.
Relatedness :National : REV/AMD UNI 8698:2001
** End of Subsector **
Subsector N09: PLASTICS.
Subsector : N09 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 05401241/0001 Project EstablishedICS :National Ref : 05401241Title : Polyethylene (PE) pipes - PE 80, PE 100 - General quality requirements, testing
Relatedness :National : New
Subsector : N09 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 05401242/0001 Project EstablishedICS :National Ref : 05401242Title : Polyethylene (PE) - Pipes PE 80, PE 100 - Dimensions
Relatedness :National : New
Subsector : N09 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035654/0001 Project EstablishedICS :National Ref : PNE 53963Title : Plastics. Cellular flexible polymeric materials. Tolerances on the nominal value of
polyurethane (PUR) conglomerate foams characteristics.Scope : It pretends to show to the users (furniture, manufacturers, packaging industry,
construction, etc.) and final consumers, the deviations that may occur on the values of main physical properties of pieces cutted from the same block.
Relatedness :National : REV/AMD UNE 53963:2000 IN
Page 48
** End of Subsector **
Subsector N14: PLASTICS PIPES.
Subsector : N14 Registration Date : 2010-05-28Organization : CYSCountry : CyprusProject ID : 00016003/0001 Project EstablishedICS :National Ref :Title : Suitability of plastic piping systems for use in contact with intended for human
consumption
Relatedness :National : New
Subsector : N14 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023280/0001 Project EstablishedICS : 23.040.20National Ref : ÖNORM B 5174-1Title : Pipes of polypropylene for special applications - Dimensions, requirements, tests, proof
of conformity - Part 1: Non-modified PP-materials PP-H, PP-B, PP-R, PP-RCTScope : This ÖNORM defines dimensions, requirements, tests and the proof of conformity for pipes
of polypropylene, which due to differences concerning material, wall construction or field of application are neither covered by ÖNORM EN ISO 15874 (all parts), nor by ÖNORM EN ISO 15494, nor by ÖNORM EN ISO 21003 (all parts). In this ÖNORM also the procedure for the proof of conformity of this kind of pipes made of polyproylene is defined. The pipes which are under the scope of this standards are either solid wall pipes with homogeneous wall or with multilayer wall constructions consisting of several of the permissible materials defined under table 2 of this standard.
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 49
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector S : HEALTH, ENVIRONMENT AND MEDICAL EQUIPMENT
Register issued on : 2010-06-04
Page 50Subsector S01: ACOUSTICS AND SOUND INSULATION.
Subsector : S01 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 20000947/0001 Project EstablishedICS : 17.140.20National Ref : U20000947Title : Acoustics - Method to evaluate the acoustic impact and environment for different kinds
of sources - Par 7: Wind turbines noiseScope : This standard defines the procedure for the evaluation of the acoustic impact and
environment of wind turbines.
Relatedness :National : New
** End of Subsector **
Subsector S04: PROTECTIVE CLOTHING AND EQUIPMENT.
Subsector : S04 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168536/0001 Project EstablishedICS :National Ref : XP S72-427Title : Mouthguard for use in sports - Safety requirements and test methods
Relatedness :National : New
** End of Subsector **
Subsector S07: ANAESTHETIC AND RESPIRATORY EQUIPMENT.
Subsector : S07 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168416/0001 Project EstablishedICS :National Ref : PR NF S90-351Title : Health care establisments - cleanrooms and associated controlled environments -
Requirements for the control of airborne contamination
Relatedness :National : New
** End of Subsector **
Subsector S08: AIR QUALITY.
Subsector : S08 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168415/0001 Project EstablishedICS :
Page 51
National Ref : PR XP X43-269Title : Air quality - Workplace atmosphere - Determination of the number concentration of
fibres by phase contrast optical microscopy - Membrane filter method
Relatedness :National : New
** End of Subsector **
Subsector S09: WATER QUALITY AND WATER SUPPLY.
Subsector : S09 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023294/0001 Project EstablishedICS : 13.060.30, 23.040.50, 93.030National Ref : ONR 22504-1Title : Base liners for concrete manhole bases - Part 1: Base liners made out of polypropylene
(PP) - Requirements, tests, quality controlScope : This ONR lays down terms, nominal diameters, dimensions, requirements, tests and the
quality control for base liners of polypropylene serving for concrete manhole bases. This ONR is appliccable for products to be used in manholes or inspection chambers according to ÖNORM EN 1917 and ÖNORM B 5072 for gravity sewerage and drainage conduits. Products which may be installed in-situ or which are used for renovation of manholes or inspection chambers are not within the scope of this ONR. This ONR serves as the basis for the proof of conformity of the relevant products. Furthermore, in this ONR reference is made to test methods which have to used in addition to the provisions of this ONR.
Relatedness :National : New
Subsector : S09 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023295/0001 Project EstablishedICS : 13.060.30, 23.040.50, 93.030National Ref : ONR 22504-2Title : Base liners for concrete manhole bases - Part 2: Base liners made out of glass
reinforced thermosetting plastics based on polyester resins (GRP) - Requirements, tests, quality control
Scope : This ONR lays down terms, nominal diameters, dimensions, requirements, tests and the quality control for base liners of fibre-reinforced plastics on the basis of polyester resins (UP) serving for concrete manhole bases. This ONR is appliccable for products to be used in manholes or inspection chambers according to ÖNORM EN 1917 and ÖNORM B 5072 for gravity sewerage and drainage conduits. Products which may be installed in-situ or which are used for renovation of manholes or inspection chambers are not within the scope of this ONR. This ONR serves as the basis for the proof of conformity of the relevant products. Furthermore, in this ONR reference is made to test methods which have to used in addition to the provisions of this ONR.
Relatedness :National : New
Subsector : S09 Registration Date : 2010-05-11
Page 52
Organization : NENCountry : NetherlandsProject ID : 50001564/0001 Project EstablishedICS : 13.060.50National Ref : NEN 6578:1985/A1:2010 Concept nlTitle : Rain water - Potentiometric determination of total inorganic fluoride contentScope : This standard specifies a method for the potentiometric determination of total inorganic
fluoride in rain water. It applies to rain water with a fluoride content of 1,0 to 25 μ mol/l of F-
Relatedness :National : New
Subsector : S09 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168496/0001 Project EstablishedICS :National Ref : PR NF T90-601Title : Water treatment. Ion exchange resins. Rerelease test of total organic carbon.
Relatedness :National : New
** End of Subsector **
Subsector S18: STERILIZATION OF EQUIPMENT.
Subsector : S18 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 06301390/0001 Project EstablishedICS :National Ref : 06301390Title : Disinfection - Steam disinfection apparatus - Part 3: Efficiency testing
Relatedness :National : New
Subsector : S18 Registration Date : 2010-05-20Organization : UNICountry : ItalyProject ID : 42128290/0001 Project EstablishedICS : 11.080.01National Ref : U42128290Title : Guide to design, development and control of a recondition process for reusable medical
devices that shall be sterilized by steamScope : This Technical Report gives a guidelines for the design, development and control of a
recondition process for reusable medical devices that could be sterilized by steam. It gives criteria for identification of this reusable medical devices that could be reconditioned according their critical aspects.
Relatedness :National : New
Page 53
** End of Subsector **
Subsector S20: WASTE COLLECTION, HANDLING AND TRANSPORTATION
Subsector : S20 (Secondary Subsector)
Registration Date : 2010-05-04
Organization : BSICountry : United KingdomProject ID : 01001020/0001 Project EstablishedICS :National Ref : BS 5502-31:1995+A1Title : Buildings and structures for agriculture. Part 31. Guide to the storage and handling of
waste. Amendment
Relatedness :National : New
Subsector : S20 (Secondary Subsector)
Registration Date : 2010-05-04
Organization : BSICountry : United KingdomProject ID : 01001021/0001 Project EstablishedICS :National Ref : BS 5502-50:1993+A1Title : Buildings and structures for agriculture. Part 50. Code of practice for the design,
construction and use of storage tanks and reception pits for livestock slurry. Amendment
Relatedness :National : New
** End of Subsector **
Subsector S23: PERSONAL & PROPERTY PROTECTION AGAINST AGGRESSION/ BURGLARY.
Subsector : S23 Registration Date : 2010-05-27Organization : AENORCountry : Spain Latest Date for Comments : 2010-07-06Project ID : P0035156/0002 Draft for public enquiryICS :National Ref : PNE 108136Title : Anchorage procedures for secure storage units.Scope : This spanish standard establishes the different options for anchoring in relation to the type
of fastener and anchored nature of the place of the secure storage units, to hinder their removal. Anchoring complements the degree of security established in European Standard EN 1143-1.
Relatedness :National : New
** End of Subsector **
Subsector S99: UNDETERMINED.
Subsector : S99 Registration Date : 2010-05-12
Page 54
Organization : ASICountry : AustriaProject ID : 00023293/0001 Project EstablishedICS : 11.160National Ref : ÖNORM V 5101Title : First aid equipment for multi-track motor vehicles - Requirements, tests Scope : This ÖNORM specifies requirements for first aid equipment for multi-track motor vehicles.
Relatedness :National : New
Subsector : S99 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 05300323/0001 Project EstablishedICS :National Ref : 05300323Title : Motor vehicle for the transportation of handicapped persons - Part 2: Restraint systems;
concepts, requirements, testing
Relatedness :National : New
Subsector : S99 Registration Date : 2010-05-13Organization : UNICountry : ItalyProject ID : 42048370/0001 Project EstablishedICS : 11.040.10National Ref : U42048370Title : Guidance to acceptance and management of pipeline systems for compressed medical
gases and vacuum and anaesthetic gas scavenging disposal systemsScope : This guideline gives operative indications about the acceptance procedure (including
testing and functioning) of new medical gas pipeline systems and vacuum and anaesthetic gas scavenging disposal systems.
Relatedness :National : REV/AMD UNI 1100:2004
Subsector : S99 Registration Date : 2010-05-25Organization : AFNORCountry : FranceProject ID : FA168487/0001 Project EstablishedICS :National Ref : PR NF X30-510Title : Terminology of health care waste
Relatedness :National : REV/AMD NF X30-510:200310 (X30-510PR)
Subsector : S99 Registration Date : 2010-05-25Organization : AFNORCountry : France
Page 55
Project ID : FA168488/0001 Project EstablishedICS :National Ref : PR NF X30-502Title : Packaging for medical care waste - Dental amalgam waste packaging - Tests and
specifications
Relatedness :National : REV/AMD NF X30-502:200310 (X30-502)
** End of Subsector **
** End of Sector **
Information procedure Page 56
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector T : TRANSPORT, MECHANICAL HANDLING AND PACKAGING
Register issued on : 2010-06-04
Page 57Subsector T02: AEROSPACE.
Subsector : T02 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 13114596/0001 Project EstablishedICS :National Ref : 13114596Title : Aerospace - Determination of coefficient of friction of bolt/nut assemblies under
specified conditions
Relatedness :National : New
** End of Subsector **
Subsector T06: METAL AND PLASTIC CONTAINERS.
Subsector : T06 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035651/0001 Project EstablishedICS :National Ref : PNE 62422Title : Construction of double skin tanks by transforming « in situ » single skin steel tanksScope : This project of standard is to be set up in order to define the technical specifications which
guarantee the construction procedure for a double contention, built « in situ » by mean of transforming a pre-existing underground with single skin steel tanks
Relatedness :National : New
Subsector : T06 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035658/0001 Project EstablishedICS :National Ref : PNE 62351-1:1999/1MTitle : Steel storage tanks for carburant and combustible liquids. Tanks with capacity up to
3000 litres. Part 1: Single skin tanksScope : This standard modifies the clause 6.3 in order to include a nozzle in the bottom of the tank
for emergency situations.
Relatedness :National : REV/AMD UNE 62351-1:1999
Subsector : T06 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035660/0001 Project EstablishedICS :National Ref : PNE 62352:1999/1MTitle : Steel storage tanks for carburant and combustible liquids. Above ground
parallelepipedical tanks with capacity up to 2000 litres.
Page 58
Scope : This standard modifies the clause 6.3 in order to include a nozzle in the bottom of the tank for emergency situations.
Relatedness :National : REV/AMD UNE 62352:1999
** End of Subsector **
Subsector T14: PACKAGING.
Subsector : T14 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 11500836/0001 Project EstablishedICS :National Ref : 11500836Title : Oxygen scavengers for packaging applications - Part 1: Determination of capacity
Relatedness :National : New
Subsector : T14 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 11500837/0001 Project EstablishedICS :National Ref : 11500837Title : Packaging - Boxes manufactured from solid fibre-board or corrugated board - Part 1:
For cylindrical aluminium tubes
Relatedness :National : New
Subsector : T14 Registration Date : 2010-05-12Organization : DINCountry : GermanyProject ID : 11500838/0001 Project EstablishedICS :National Ref : 11500838Title : Packaging - Boxes made from solid fibre-board or corrugated board - Part 2: For conical
aluminium tubes
Relatedness :National : New
** End of Subsector **
Subsector T19: ROAD SAFETY.
Subsector : T19 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035620/0001 Project EstablishedICS :
Page 59
National Ref : PNE 135314Title : Vertical signs. Galvanized steel profiles used as posts of the signs, side posters and
directional signs. Screw products. Characteristics and test methods.Scope : This standard revises a previous one which specifies the characteristics and test methods of
galvanized steel screw and beams used as post of the signs, side posters and directional signs.
Relatedness :National : REV/AMD UNE 135314:2009
Subsector : T19 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035621/0001 Project EstablishedICS :National Ref : PNE 135331Title : Vertical signs. Fixed metallic vertical road traffic sings. Non retroreflective area. Paints.
Characteristics and test methods.Scope : This standard revises a previous one which specifies the characteristics and test methods for
the non retroreflective painted area of the fixed metallic vertical road traffic signs
Relatedness :National : REV/AMD UNE 135331:2004, UNE 135331:2004 ERRATUM:2006
Subsector : T19 Registration Date : 2010-05-31Organization : AENORCountry : SpainProject ID : P0035622/0001 Project EstablishedICS :National Ref : PNE 135362-1Title : Vertical signs. Road delineators. Part 1: Polychloride vinyl sign post. Characteristics,
dimensions and test methods.Scope : This standard revises a previous one which defines some characteristics, dimensions and
test methods for the road delineators made of rigid PVC.
Relatedness :National : REV/AMD UNE 135362:1994 EX
** End of Subsector **
** End of Sector **
Information procedure Page 60
Monthly Notifications Register
Notifications registered at CCMC from 2010-05-01 to 2010-05-31
Sector Z : INFORMATION TECHNOLOGY
Register issued on : 2010-06-04
Page 61Subsector Z03: COMMON O.S.I. ACTIVITIES
Subsector : Z03 Registration Date : 2010-05-12Organization : ASICountry : AustriaProject ID : 00023274/0001 Project EstablishedICS : 35.100.01National Ref : ÖNORM A 2642Title : Information technology - Open systems interconnection - Procedures for the registration
of information objects in AustriaScope : This ÖNORM defines the registration procedure for OSI registrations according to ISO/IEC
in 9834-1. This ÖNORM applies accordingly for the regulation of the registration of institutions which are entitled to the assignment of a certain subset of object call signs.
Relatedness :National : New
** End of Subsector **
** End of Sector **
2010-05
List of non-electrotechnical subsectors
Sector A: Services
Subsector Title ISO/TC CEN/TC
reference reference
A01 Tourist services / 329; CEN/WS ETO
A02 Cleaning services / 328
A03 Postal services / 331
A04 Transportation services / 320; CEN/WS 016
A05 Maintenance services / 319
A06 Building and construction services / 330
A07 Translation services /
A08 Funeral services / CEN/BT/TF 139
A09 Facility management / 348
A10 Services of Real Estate Agents / CEN/BT/TF 180,
373
A11 Security Services / CEN/BT/TF 167;
391; 384; 370;
CEN/WS 044
A12 Consultancy Services / 395; 381
A99 Undetermined / CEN/WS 002 CEN/WS 004 CEN/WS 037 CEN/WS 039 CEN/WS 041 CEN/WS 051 375; 374; 376; 385
Sector B: Building and construction
Subsector Title ISO/TC CEN/TC
reference reference
B01 Fire protection 21 70; 72; 191; 192
B02 Structures 59; 98 166; 167; 250; 277;
346; 349 284; 288; 297; 340;
B03 Concrete 71 104; CEN/WS 009
B04 Cement 74; 77 51
B05 Fire tests 92 127
B06 Gypsum / 241
B07 Glass 160 129
B08 Doors and windows 162 33
B09 Thermal matters 163 88; 89; 371
CEN/BT WG 173 CEN/WS 036
B10 Timber structures 165 124
B11 Metal structures 167 135
B12 Masonry 179; 196 125; 246
B13 Solar energy 180 312
B14 Geotechnics 182 341; 396
B15 Sanitary appliances / 163; 7
B16 Taps / /
B17 Lighting equipment and lighting / 50; 169 application technology
B18 Scaffolding / 53
B19 Ceramic tiles 189 67
B20 Drainage equipment / 165
B21 Baths / /
B22 Wallcoverings / 99
B23 District heating / 107
B24 Auxiliary and handicraft work / /
B25 Gas distribution installation and / 234; 235; 282 related equipment
B26 Road building and maintenance / 178; 227
B27 Waterproofing materials / 128; 254; 361; 314
B28 Floor coverings 38/SC 12 134
B29 Aggregates / 154
B30 Floor and surfacing / 217; 303; 323; 390
B31 Heating systems in buildings / 228; 247
B32 Precast concrete products / 177; 229 B33 Building design 205 315; 325; 388
B34 Building and construction – Environmental aspect 350; 351
B99 Undetermined / /
Sector C: Chemicals, chemical engineering and food products
Subsector Title ISO/TC CEN/TC
reference reference
C01 Food products 34 174; 275; 302; 360 307; 327; 338; 387 CEN/WS 008 CEN/WS 018
C02 Paints and related products 35 139; 298; 173
C03 Chemistry 47 317; 363
C04 Laboratory glassware 48 332
C05 Lac / /
C06 Essential oils 54 /
C08 Pesticides 81 /
C09 Surfactants 91 276
C10 Starch 93 /
C11 Tobacco 126 401
C12 Glass plant / /
C13 Fertilizers 134 223; 260
C16 Wood preservatives / /
C17 Trees and plants / /
C18 Adhesives / 193
C19 Chemical analysis 201; 202 382; 347
C20 Explosives and firework / 212; 321
C21 Cosmetics 217 392
C99 Undetermined / 386
Sector F: Fundamental standards
Subsector Title ISO/TC CEN/TC
reference reference
F01 Technical drawings 10 /
F02 Units & symbols 12 /
F03 Preferred numbers 19 /
F04 Sieves 24 /
F05 Measuring instruments 30; 113 92; 171; 176; 237;
294; 318; 244; 367 141; CEN/WS 011
F06 Terminology principles 37 /
F07 Documentation and information 46 304; CEN/WS 024 CEN/WS 010 CEN/WS 023 CEN/WS 028 CEN/WS 014 CEN/WS 050 CEN/WS 006 368
F08 Surfaces / 290
F09 Banking 68 /
F10 Statistics 69 /
F12 Information processing systems 204 224; 225; 251; 278; CEN/WS CPF CEN/WS CIS CEN/WS ODR CEN/WS CID 287; 311; 365
F13 Environmental tests / /
F14 Graphical technology, 130 / sign-boards and nameplates
F15 Material testing in general 135 138; CEN/WS 007 CEN/WS 021 CEN/WS 033
F16 Graphical symbols 145 /
F17 Administrative documents 154 CEN/WS MMU
F18 Micrographics 171 /
F19 Optics 172; 187 123; 170
F20 Quality assurance 176 CEN/CLC/TC1 CEN/CLC/WG QS CEN/WS 030 362
F21 Value analysis and project / 279 network
F22 Logistics / 379; 273
F23 Energy 203 CEN/CLC/JWG 3 CEN/CLC/JWG 4 CEN/WS 027
F99 Undetermined / 389
Sector H: Products for household and leisure use
Subsector Title ISO/TC CEN/TC
reference reference
H01 Cinematography 36 372
H02 Photography 42 /
H03 Consumer questions / 291
H04 Sports equipment 83 136
H05 Oil and gas burners / 47; 131
H06 Horology 114 /
H07 Space heating 116 62; 110; 130; 179; 180
H08 Sizing systems 133; 137 /
H09 Furniture 136 207
H10 Sewing machines 148 /
H11 Heater controls 161 58
H12 Ceramic and glass-ware for food 166 /
H13 Jewellery 174 CEN/WS 047
H14 Caravans 177 245
H15 Toys 181 52
H17 Oil stoves / 46
H18 Central heating boilers / 48; 57; 109; 269
H19 Non-electric cookers and barbecues / 49; 281; 295
H22 Smokers’ lighters and matches / 355; 87
H23 Ladders / 93
H24 Tactile danger warnings / /
H25 Large gas appliances / 106; CEN/CLC/JWG FCGA
H26 Sealing materials / 108; 208
H27 Educational equipment / /
H28 Hunting 191 /
H29 Heat pumps / 113
H30 Equipment for children / 252
H31 Dedicated LPG appliances / 181
H32 Culinary utensils 186 194
H33 Footwear (excluding protective / 309 footwear)
H34 Child safety / CEN/BT/WG 117 398
H99 Undetermined / 299; 364; 369; 402
Sector I: Mechanical engineering
Subsector Title ISO/TC CEN/TC
reference reference
I01 Screw threads 1 /
I02 Fasteners 2 185
I03 Limits & fits / /
I04 Rolling bearings 4 /
I05 Iron pipes 5 203
I06 Pressure vessels 11 54
I07 Shafts 14 /
I08 Agricultural machines 23 144, 334
I09 Small tools 29 213
I10 Splines / /
I11 Machine tools 39 142; 143; 145; 255
I12 Pulleys & belts 41 188
I13 Gas containers 58 23; 286
I14 Gears 60 /
I15 Equipment for petroleum industry 67 12
I16 Internal combustion engines 70; 192 270
I17 Machinery in general 72; 199 114; 153; 214; 313 (including safety) 271, 337; 399; 397 CEN/WS 025
I18 Mining 82 196
I19 Nuclear energy 85 /
I20 Refrigeration 86 44; 182
I21 Chains and chain wheels 100 /
I22 Vacuum technology 112 /
I23 Pumps 115 197
I24 Industrial fans 117 356
I25 Compressors 118 232
I26 Plain bearings 123 /
I27 Earth moving and construction 127; 195 151 equipment
I28 Fluid power 131 /
I29 Gas cleaning / 195
I30 Air distribution / 156
I31 Valves 153; 185 69; 236; 105
I32 Flanges / 74
I33 Information processing in 184 310 automation
I34 Non-ferrous metallic pipes / /
I35 Leisure and recreational machines / 152
I36 Thermoprocessing technology / 186
I37 Printing and paper machines / 198
I38 Leather production, tannery and / 200; 201 related machinery
I39 Machines for metal processing / 202; 322
I40 Industrial piping networks / 267
I41 Membrane filters / 272
I42 Potentially explosive atmospheres / 305
I43 Hydrogen energy 197 /
I44 Nanotechnologies 229 352
I99 Undetermined / CEN/CLC/JTF PE; CEN/CLC/TC 2
65, 157
Sector M: Metallic materials
Subsector Title ISO/TC CEN/TC
reference reference
M01 Steel 17 CEN/TC 342; 344; ECISS/TC 6 ECISS/TC 7 ECISS/TC 9 ECISS/TC 10 ECISS/TC 11 ECISS/TC 12 ECISS/TC 13 ECISS/TC 15 ECISS/TC 19 ECISS/TC 20 ECISS/TC 21 ECISS/TC 22 ECISS/TC 23 ECISS/TC 24 ECISS/TC 26 ECISS/TC 27 ECISS/TC 28 ECISS/TC 29 ECISS/TC 5 ECISS/TC 14 ECISS/TC 100 ECISS/TC 102 ECISS/TC 103 ECISS/TC 104 ECISS/TC 105 ECISS/TC 106 ECISS/TC 107 ECISS/TC 108 ECISS/TC 109 ECISS/TC 110
M02 Zinc / 209
M03 Foundry technology, 25 190; ECISS/TC 31 ECISS/TC 111 including cast iron
M04 Copper 26 133
M05 Welding 44 121
M06 Dimensions of wrought products / /
M07 Manganese and chromium 65 /
M08 Light alloys 79 132
M09 Iron ores 102 /
M10 Metallic coatings 107 240
M11 Powder metallurgy 119 /
M12 Aluminium ores 129 /
M13 Ferroalloys 132 /
M14 Nickel 155 /
M15 Metallic corrosion 156 262; 219
M16 Mechanical tests for metals 164 ECISS/TC 1 ECISS/TC 2 ECISS/TC 101
M17 Heavy metal ores 183 /
M18 Metal wire products / ECISS/TC 30 CEN/BT/TF 196
378
M20 Tin and tin alloys / 220
M21 Precious metals / 283
M22 Lead and lead alloys / 306
M99 Undetermined / /
Sector N: Non-metallic materials
Subsector Title ISO/TC CEN/TC
reference reference
N01 Paper and board 6 172
N02 Solid fuels 27 335; 343;383 CEN/WS 019
N03 Petroleum products 28 19; 336 CEN/WS 038
N04 Refractories 33 187
N05 Textiles 38 189; 248
N06 Rubber 45 218; 366 CEN/WS 003
N07 Sawn timber 55 38; 175
N08 Mica / /
N09 Plastics 61 249
N10 Cork 87 /
N11 Wood-based panels 89 112
N12 Timber products 99 /
N13 Leather 120 289
N14 Plastics pipes 138 155
N17 Fluorspar 175 /
N18 Glass-fibre reinforced plastics / /
N19 Tapes / 253
N20 Ceramics 206 184
N21 Gaseous fuels and combustible gas 158; 193 238
N22 Feather and related materials / 222
N99 Undetermined / /
Sector S: Health, environment and medical equipment
Subsector Title ISO/TC CEN/TC
reference reference
S01 Acoustics and sound 43 126; 211 insulation
S02 Transfusion equipment 76 /
S03 Syringes 84 /
S04 Protective clothing and equipment 94 85; 158; 159; 160; 161; 162 CEN/WS 026
S05 Dentistry 106 55
S06 Vibration & shock 108 231
S07 Anaesthetic and respiratory 121 215 equipment
S08 Air quality 146 137; 243; 264; CEN/CLC WG/CMI
S09 Water quality and water supply 147 164; 230; CEN/WS 001 CEN/WS 034
S10 Surgical implants 150 285; CEN/CLC JWG/AIMD
S11 Contraceptives 157 /
S12 Gas analysis / /
S13 Ergonomics 159 122
S14 Prosthetics 168 /
S15 Surgical instruments 170 /
S16 Aids for the disabled 173 293
S17 Respiratory protective devices / 79
S18 Sterilization of equipment 198 102; 204
S19 First aid equipment and rescue systems / 239
S20 Waste collection, handling and / 183 transportation
S21 Laboratory medicine, clinical 194 140; 206; 233; pathology and biosafety 257; 258; 316 CEN/CLC/TC 3 CEN/WS 031 CEN/WS 053
S22 Energy saving / CEN/WS 005 CEN/WS 015
S23 Personal & property protection against aggression/Burglary protection / 263
S24 Soil quality 190 345; CEN/WS 032
S25 Chemical disinfectants and / 216 antiseptics
S26 Environmental management 207 CEN/WS 040
S27 Waste - Characterization, treatment / 292; 308; and streams CEN/BT/TF 120
S28 Demining / CEN/WS 029 CEN/WS 013
S99 Undetermined / 205; CEN/BT/TF 127 394; 259; 357; 358; 359; 380; 400; 403 CEN/WS PCEC CEN/WS 012 CEN/WS 020
Sector T: Transport, mechanical handling and packaging
Subsector Title ISO/TC CEN/TC
reference reference
T01 Shipbuilding and maritime 8; 188 15; 300 structures
T02 Aerospace 20 274; AECMA; ECSS 377
T03 Road vehicles 22 301; 326 CEN/WS IMA
T04 Tyres 31 /
T05 Pallets 51 /
T06 Metal and plastic containers 52 210; 221; 265; 266; 268; 296 393
T07 Glass containers 63 /
T08 Cranes 96 147
T09 Materials handling and 101 148; 149 storage equipment
T10 Freight containers 104 119; 280
T11 Steel wire ropes 105 /
T12 Industrial trucks 110 150; 324
T13 Lifting chains, hooks and ropes 111 168
T14 Packaging 122 261; 120
T15 Cycles 149 333
T16 Lifts & escalators 178 10; 242
T17 Builders hoists / /
T18 Elevating platforms / 98
T19 Road safety / 226; 339
T20 Tram- and railway engineering / 256; / CEN/CLC WG/FPR
T21 Packaging machines / 146
T22 Off-road vehicles / 354
T99 Undetermined / CEN/WS TAF
Sector Z: Information technology
Subsector Title ISO/TC CEN/TC
Z01 Radiocommunication for IT / /
Z02 Telephony, telegraphy for IT / CEN/CLC - ETSI
Z03 Common O.S.I. activities / CEN/CLC - EWOS
Z99 Undetermined / 353; CEN/WS DFA CEN/WS DIR CEN/WS EBES CEN/WS ECH CEN/WS ECO CEN/ES EFI CEN/WS ESI CEN/WS FAS CEN/WS FUN CEN/WS IEC CEN/WS JXF CEN/WS LCT CEN/WS LTS CEN/WS MDC CEN/WS MET CEN/WS POR CEN/WS URI CEN/WS XFS CEN/WS ORC CEN/WS CTC CEN/WS XML CEN/WS MEE CEN/WS SCE CEN/WS MES CEN/WS UDP CEN/WS MMI CEN/WS FS2 CEN/WS AUT CEN/WS ICT CEN/WS KMA CEN/WS TEX CEN/WS SAN CEN/WS DPP CEN/WS HIC CEN/WS MLX CEN/WS eGO CEN/WS BII CEN/WS ADN CEN/WS CAT CEN/WS CST CEN/WS DIS CEN/WS ESR CEN/WS EUR CEN/WS FIN CEN/WS GEN CEN/WS ISD CEN/WS NEA CEN/WS NOM