modified one-third tubular plate with hook for distal ...this modified implant can be used in...

2
Fig. 1: (a) Shows two similar one-third tubular plates prior to modification. (b) The distal end of the left one-third tubular plate has been cut with a plate cutter at 45 degree, creating two hooks. (c) Shows the difference between the two one-third tubular plates after bending. After cutting the plate, the end of the plate can be bent to accommodate a distal screw as well as being fitted to the distal part of the lateral malleolus. Note that the trajectory of the distal screw can now be directed at a more superior-lateral angle compared to the screw trajectory in an uncut plate. 60 Malaysian Orthopaedic Journal 2019 Vol 13 No 1 Kow RY, et al Dear Editor, Fracture of the lateral malleolus is a commonly encountered problem in the orthopaedic fraternity 1 . Among the lateral malleolus fractures, Weber type B is the most common injury, accounting for 60% of all ankle fractures 2 . Anatomical reduction and fixation of the distal lateral malleolus fractures are crucial to improve the outcomes in patients 1 . They are normally done with a one-third tubular plate with or without an inter-fragmentary lag screw. One-third tubular plate is a suitable implant as there is limited soft tissue coverage overlying the lateral malleolus. A commonly encountered problem intra-operatively is limited space for distal screw placement 3 . Placement of only one distal screw is insufficient to ensure rotational stability, especially in osteoporotic bone 3 . Locking plate has been proposed to treat these fractures, but a significant increase in wound complications associated with locking compression plate discourage the use of these implants 4 . Heim et al described a technique in which the one-third tubular plate is modified to form a hook at the distal plate. This modified implant can be used in malleolar fractures, olecranon fractures, distal radius fractures, distal ulnar fractures and proximal fractures of the fifth metatarsal 3 . Here, we would like to revisit this one-third tubular plate modified technique and to propose the use of the modified distal hole for placement of distal screw with different trajectory for better rotational stability (Fig. 1). By using this technique, the risk of ankle joint penetration by the distal screw is kept to the minimum (Fig. 2). Modified One-third Tubular Plate with Hook for Distal Lateral Malleolus Fracture Fixation Kow RY, MBBS, Low CL, MBBS Department of Orthopaedics, Hospital Tengku Ampuan Afzan, Kuantan, Malaysia This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited Date of submission: 17th December 2018 Date of acceptance: 17th February 2019 Corresponding Author: Ren Yi Kow, Department of Orthopaedics, Hospital Tengku Ampuan Afzan, Jalan Tanah Putih, 25100 Kuantan, Pahang Email: [email protected] doi: http://dx.doi.org/10.5704/MOJ.1903.013 (a) (b) (c) Fig. 2: (a) The modified one-third tubular plate can be used as a hook plate with one cancellous screw being placed at the second last hole of the plate. (b) A cancellous screw directly inserted at the modified distal hole of the one-third tubular plate. (c) Ankle plain radiograph of a patient who had undergone the surgery using the described method. (a) (b) (c)

Upload: others

Post on 05-Jul-2020

12 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Modified One-third Tubular Plate with Hook for Distal ...This modified implant can be used in malleolar fractures, olecranon fractures, distal radius fractures, distal ulnar fractures

Fig. 1: (a) Shows two similar one-third tubular plates prior tomodification. (b) The distal end of the left one-thirdtubular plate has been cut with a plate cutter at 45degree, creating two hooks. (c) Shows the differencebetween the two one-third tubular plates after bending.After cutting the plate, the end of the plate can be bentto accommodate a distal screw as well as being fitted tothe distal part of the lateral malleolus. Note that thetrajectory of the distal screw can now be directed at amore superior-lateral angle compared to the screwtrajectory in an uncut plate.

60

Malaysian Orthopaedic Journal 2019 Vol 13 No 1 Kow RY, et al

Dear Editor,

Fracture of the lateral malleolus is a commonly encounteredproblem in the orthopaedic fraternity1. Among the lateralmalleolus fractures, Weber type B is the most commoninjury, accounting for 60% of all ankle fractures2.Anatomical reduction and fixation of the distal lateralmalleolus fractures are crucial to improve the outcomes inpatients1. They are normally done with a one-third tubularplate with or without an inter-fragmentary lag screw.One-third tubular plate is a suitable implant as there islimited soft tissue coverage overlying the lateral malleolus.A commonly encountered problem intra-operatively islimited space for distal screw placement3. Placement of onlyone distal screw is insufficient to ensure rotational stability,especially in osteoporotic bone3. Locking plate has been

proposed to treat these fractures, but a significant increase inwound complications associated with locking compressionplate discourage the use of these implants4.

Heim et al described a technique in which the one-thirdtubular plate is modified to form a hook at the distal plate.This modified implant can be used in malleolar fractures,olecranon fractures, distal radius fractures, distal ulnarfractures and proximal fractures of the fifth metatarsal3.Here, we would like to revisit this one-third tubular platemodified technique and to propose the use of the modifieddistal hole for placement of distal screw with differenttrajectory for better rotational stability (Fig. 1). By using thistechnique, the risk of ankle joint penetration by the distalscrew is kept to the minimum (Fig. 2).

Modified One-third Tubular Plate with Hook for DistalLateral Malleolus Fracture Fixation

Kow RY, MBBS, Low CL, MBBS

Department of Orthopaedics, Hospital Tengku Ampuan Afzan, Kuantan, Malaysia

This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited

Date of submission: 17th December 2018Date of acceptance: 17th February 2019

Corresponding Author: Ren Yi Kow, Department of Orthopaedics, Hospital Tengku Ampuan Afzan, Jalan Tanah Putih, 25100 Kuantan,PahangEmail: [email protected]

doi: http://dx.doi.org/10.5704/MOJ.1903.013

(a) (b) (c)

Fig. 2: (a) The modified one-third tubular plate can be used asa hook plate with one cancellous screw being placed atthe second last hole of the plate. (b) A cancellous screwdirectly inserted at the modified distal hole of theone-third tubular plate. (c) Ankle plain radiograph of apatient who had undergone the surgery using thedescribed method.

(a) (b) (c)

13-LETTER_OA1 3/26/19 4:00 PM Page 60

Page 2: Modified One-third Tubular Plate with Hook for Distal ...This modified implant can be used in malleolar fractures, olecranon fractures, distal radius fractures, distal ulnar fractures

Modified One-third Tubular Plate

61

REFERENCES

1. Sanders JS, Fader RR, Mitchell JJ. Posterior versus lateral plate fixation of short oblique fractures of the distal fibula: a literaturereview. Clin Res Foot Ankle. 2016; 4: 200. doi: 10.4172/2329-910X.1000200

2. Chun D, Sharma AR, Kim DY, Ulagpan A, Jagga S, Lee S, et al. A novel remedy for isolated weber B ankle fractures: surgicaltreatment using a specialized anatomical locking plate. Biomed Res. 2017; 28(19): 8417-22.

3. Heim D, Niederhauser K. One-third tubular hook plate. Oper Orthop Traumatol. 2007; 19(3): 305-9.4. Schepers T, Van Lieshout EM, De Vries MR, Van der Elst M. Increased rates of wound complications with locking plates in distal

fibular fractures. Injury. 2011; 42(10): 1125-9. doi: 10.1016/j.injury.2011.01.009

13-LETTER_OA1 3/26/19 4:00 PM Page 61