model: aspt- g, w, lo & b
DESCRIPTION
Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955TRANSCRIPT
01 04/07issue 181759
COFFEE TABLEMODEL: ASPT- G, W, LO & B
ASSEMBLY INSTRUCTIONS
Alphason Designs LimitedAlphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UKTel: +44 (0)1942 885600Fax: +44 (0)1942 876955
www.alphasondesigns.com
Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this coffee table.
Please Note:Maximum load for the glass shelves is 70Kg each.This support must be assembled in accordance with these assembly instructions.
IMPORTANT INFORMATION!1) Before starting assembly please take time to familiarise yourselfwith the instructions and the components listed on the back page,as this product could be unstable if incorrectly installed.2) Do not place hot or cold items against or in close proximity toany glass surface unless an adequately thick insulating material isused to prevent such items coming into contact with the glass.3) Do not strike the glass with hard or pointed items.4) When cleaning glass panels use a damp cloth or leather withwashing up liquid or soft soap if necessary; do not use washingpowders or other substances containing abrasives as these mayscratch the glass.5) Do not sit or stand upon horizontal glass surfaces.6) In order to maintain a high quality finish, when cleaningwooden panels please use a soft cloth with a suitable furniturepolish if required.7) Alphason Designs uses real wood veneers, consequently slightcolour and pattern variation may occur and does not indicate aproduct defect. With natural wood, exposure to direct sunlightcan produce colour change and should be avoided. Any slightchange in colour over time does not indicate a product defect.
Place second side panel onto support bars ensure the
chrome washers are correctly located into the holes in side
panel .
Attach remaining chrome washers , screws and cover
caps onto all four support bars.
STAGE 2
•
2.2.
3.3.
01 04/07issue 181759
STAGE 3
H
STAGE 1
Place one side panel on its bottom edge on a clean flat
surface to avoid any damage. Place chrome washers
either side of the side panel shown in Fig 1a. With
screw attach support bar .
Attach remaining 3 support bars to side panel in the same way.
EACH SUPPORT BAR HAS A FLAT FACE. ENSURE THE FLAT FACE IS FACING THE TOP OF THE UNIT AS SHOWN.
Fit all cover caps into screws and tighten by hand.
A
H
1.1.
GA
E A
E
G
Place side panel with the four support bars
attached flat onto a clean surface to avoid any damage.
Place four chrome washers on the ends of the four
support bars
•
•
A
G
A
H•
F
FLATFACE.
F H
TOPOFUNIT.
A EG
A
G
GH
•
•
•
G
A
F
A
E
1a.1a.
H
G
G
•
F
01 04/07issue 181759
5.5.
STAGE 4
•
4.4.
X12
Remove self adhesive clear buffer from
backing and carefully position three equally
along each rod on the flat face.
ENSURE ALL SUPPORT BARS FLAT FACES ARE FACING THE TOP EDGE AS SHOWN.
TOP OFUNIT
D
DD
C•
STAGE 5
Place carefully the glass shelves and onto support bars ensuring the glass shelves rest on clear buffers .
B
D
Congratulations your coffee table is complete!
B
DESCRIPTION QTY PACKED BY
2
1
1
COMPONENT
MODEL: ASPT- G, W, LO & BCERTIFICATE OF CONFORMITY
01 04/07issue 181759
A
B
16
SMALL TOP GLASS SHELF
LARGE BOTTOM GLASS SHELF
SIDE PANELS
202291
141146
WALNUT - 200312LIGHT OAK - 200311BLACK - 200310GLASS - 141145
SUPPORT BAR 4
CHROME WASHER
C
D
E
F
8
GLASS SCREW KIT -202289WOODEN SCREW KIT - 202293
SCREW
G
402905
COVER CAPS 8
202292
141147
H
12CLEAR BUFFER
202290
I ALLEN KEY 1