AI-04 08/07issue 181751

ASSEMBLY INSTRUCTIONS

Alphason Designs LimitedAlphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UKTel: +44 (0)1942 885600Fax: +44 (0)1942 876955info@alphasondesigns.com

www.alphasondesigns.com

Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support.

Please Note:Maximum load for this support is 80Kg.This support must be assembled in accordance with these assembly instructions.Maximum load for each glass shelf is 60kg.

A HAMMER

CROSS-HEAD SCREWDRIVER

PLEASE NOTE OTHER TOOLS REQUIRED:

MODEL: ABR800AV CABINET

IMPORTANT INFORMATION!1) Before starting assembly please take time to familiarise yourselfwith the instructions and the components listed on the back page,as this product could be unstable if incorrectly installed.2) Do not place hot or cold items against or in close proximity toany glass surface unless an adequately thick insulating material isused to prevent such items coming into contact with the glass.3) Do not strike the glass with hard or pointed items.4) When cleaning glass panels use a damp cloth or leather withwashing up liquid or soft soap if necessary; do not use washingpowders or other substances containing abrasives as these mayscratch the glass.5) Do not sit or stand upon horizontal glass surfaces.6) In order to maintain a high quality finish, when cleaningwooden panels please use a soft cloth with a suitable furniturepolish if required.7) Alphason Designs uses real wood veneers, consequently slightcolour and pattern variation may occur and does not indicate aproduct defect. With natural wood, exposure to direct sunlightcan produce colour change and should be avoided. Any slightchange in colour over time does not indicate a product defect.

Place base panel on its back edge, on a clean

flat surface to avoid scratching. Using screws

attach panels to panel .

Insert 4x cams into large holes in panel .

Ensure arrows are pointing to the outside edge of

the panel.

Assemble side panels and onto panel .

Tighten cams in base panel .

STAGE 2

•

STAGE 3

•

•

2.2.

3.3.

Slot back panel into grooves in sides of panels and ,

and base panel .

E C D

A

A

C

Screw all remaining dowels into top panel . Take care

not to over tighten.

4.4.

A

•

AC D

Ensure back panel is correctly located before proceeding to

next stage.

• E

D

C

E

A

A x4 x6

x4

AI-04 08/07issue 181751

Position all remaining cams in panels and . Once

again ensure the arrows are pointing to the outside edge.

AC D

A

•

•

F

F

t

STAGE 1

• DC

x4

C

D

1.1.Screw dowels x4 into side panels and .

s

s

s

t

t

u

t

u

t

u

t

t

t

x4s

ss

B

B

D

Assemble top panel as shown in fig 5. Ensure dowel

fixings align with corresponding holes in panels and .

Tighten all cams from stage 3.

STAGE 5

DC•

•

B

t

5.

C

D

B

STAGE 4

AI-04 08/07issue 181751

Position location tape pieces around the rebate in

cabinet door ensure these are equally spaced around

the rebate.

Place glass panel into the rebated area. Ensure this is

firmly stuck in place.

Fit all pine tree clips into correct holes in the cabinet

door . You may need a light hammer to get these in

to place. Take extra care when carrying out this step..

STAGE 6•

•

6.G

•

G!!

G

x10x6

r

rvv

r

HH

v

ConnectingscrewUse in stage 7 Use in stage 8

STAGE 6a 6a.

j

j

STAGE 7• Using screws , screw part i from flap hinge into the 3

corresponding rebates in the cabinet door .

Using screws attach both door plates at eitherside of the door .

7.

x2

G

G

•

Gk

n

jk

p n

•

STAGE 8Using screws attach part ii from flap hinge half to therebates in the cabinet base panel .

8.

A

A

k

k j

jjk

Attach left and right hand flap stays and

using screws .

STAGE 9•

9.

p

p

p

m

ml

l

The braking force of the flapstays may require adjustment.This can be achieved byturning the screw arrowedclockwise to tighten themovement or anticlockwise toloosen the movement.

• Remove connecting screw fromflap hinges . This willform 2 halves for the followingassembly steps. i ii

iii

p

n

n

p

j

kj

Carefully lay the cabinet on its back. Push roller glides into

roller glide panels .

Turn cabinet around to sit on roller glides .

STAGE11

•

•

13.

STAGE 14

Finally insert shelf pegs into desired positions

in the side panels.

Place glass shelf into cabinet.

Attach 1 door buffer to the top end of each

side panel and .

14.

•

•

AI-04 08/07issue 181751

x4

x4

STAGE 12• Attach L-Shaped brackets with screws , into

all four corners of the back panel in positions shown.

x12

12.

F

F

x4

STAGE 10 10.

j

j

j

Using connecting screw , attach both left and right hand flap

stays to the door plates .

• on

11.x2o

o

n

STAGE 13

y z

z

q

q

q qq

w

l

w

l

w

y

y z

yz

x2x

x

x

•C D

Carefully assemble the door onto the base

panel.

Re-Connect hinges by using connecting

screw from stage 6a.

•

•

DESCRIPTION QTY PACKED BY

1

1

2

1

COMPONENT

MODEL: ABR800

CERTIFICATE OF CONFORMITY

A

B

2

1

BACK PANEL

LEFT END PANEL

TOP PANEL

BASE PANEL

CABINET DOOR 1

GLASS SHELF

C D

E

F ROLLER GLIDE PANEL

G

RIGHT END PANEL

AI-04 08/07issue 181751

GLASS PANEL FOR DOORH

I

1

This document is your guarantee that the product has reached you in the highest of quality standards. Should you have any cause for complaint please return this document with your

correspondence to the address given at the bottom of the front page.

3

18

RIGHT HAND FLAP STAY

1

1

2

12

10

8

8

DESCRIPTION QTY KIT NUMBERCOMPONENT

SHELF PEG

35mm DOWEL

CAM

m

n

o

p

q

r

s

t

l

4ROLLER GLIDE

LEFT HAND FLAP STAY

6

j

k

4

x1

AI-04 08/07issue 181751

L-SHAPED BRACKET

3 x 12 SCREW

x

12

u

v

y

FLAP HINGE(During assembly this hinge splits into 2 parts)

3 x 12 SCREW

4 x 15 SCREW

CONNECTING SCREW

4 x 25 SCREW

PINE TREE CLIP

LOCATION TAPE

DOOR PLATE

DOOR BUFFERS

z

2

6

4

2

310007

310008

310009

310011

310012

ALLEN KEY(suitable for tightening cams) 1

w