0619S20000-CV3

Grand Rapids, Michigan, U.S.A. 49504-5298

USER’S OPERATING AND INSTRUCTION MANUAL

MODEL 619-MDP

DOUGH PRESS

0619S20129 0-1

619-MDP DOUGH PRESS INDEX

Section Description Document No. Page No. SAFETY INSTRUCTIONS -------------------------------------- 0619S20141 --------------------------- 1-1 DESCRIPTION/SPECIFICATIONS --------------------------- 0619S20130---------------------------- 2-1 Description -------------------------------------------------------------------------------------------------- 2-1 Physical Specifications----------------------------------------------------------------------------------- 2-1 Electrical Specifications---------------------------------------------------------------------------------- 2-2 Electrical Wiring Diagrams ----------------------------------------------------------------------------- 2-1 OPERATING INSTRUCTIONS -------------------------------- 0619S20131 --------------------------- 3-1 Before You Start ------------------------------------------------------------------------------------------- 3-1 Basic Operation -------------------------------------------------------------------------------------------- 3-1 MAINTENANCE --------------------------------------------------- 0619S20132 --------------------------- 4-1 Cleaning ---------------------------------------------------------------------------------------------------- 4-1 Lubrication ------------------------------------------------------------------------------------------------- 4-1 Hydraulic Oil Specification ----------------------------------------------------------------------------- 4-1 Hydraulic Filter Replacement -------------------------------------------------------------------------- 4-1 Removing the Lid ---------------------------------------------------------------------------------------- 4-2 Replacing the Locking Hook or Cam ---------------------------------------------------------------- 4-2 Replacing a Pressing Plate ---------------------------------------------------------------------------- 4-3 Removing the Backing Plate --------------------------------------------------------------------------- 4-3 Replacing the Hydraulic Cylinder --------------------------------------------------------------------- 4-3 Removing the Motor -------------------------------------------------------------------------------------- 4-4 Changing the Pump or Coupling ---------------------------------------------------------------------- 4-4 Replacing the Control Valve ---------------------------------------------------------------------------- 4-5 TROUBLESHOOTING ------------------------------------------- 0619S20133 --------------------------- 5-1 The Ram up Light Does Not Come On -------------------------------------------------------------- 5-1 The Motor Hums but Will Not Start ------------------------------------------------------------------- 5-1 The Motor Runs but Stalls at Either End of the Cylinder’s Travel ---------------------------- 5-1 The Motor Runs Slowly but Stalls Easily before Completion of its Stroke ----------------- 5-1 The Motor Has Stalled and Can Not be Restarted ----------------------------------------------- 5-2 The Overload Relay Continually Trips --------------------------------------------------------------- 5-2 The Dough Press is Not Pressing Properly -------------------------------------------------------- 5-2 RECOMMENDED SPARE PARTS -------------------------- 0619S20134 --------------------------- 6-1 REPLACEMENT PARTS SECTION MAIN FRAME ASSEMBLY ------------------------------------ 0619S20135 --------------------------- 7-1 Drawing ------------------------------------------------------------------------------------------------- 7-1 Parts List ----------------------------------------------------------------------------------------------- 7-2 Continued

0619S20129 0-2

INDEX (Continued)

REPLACEMENT PARTS SECTION (Continued) Section Description Document No. Page No. COVER ASSEMBLY --------------------------------------------- 0619S20136 --------------------------- 8-1 Drawing ------------------------------------------------------------------------------------------------ 8-1 Parts List ----------------------------------------------------------------------------------------------- 8-2 HYDRAULIC ASSEMBLY -------------------------------------- 0619S20137 --------------------------- 9-1 Drawing ------------------------------------------------------------------------------------------------ 9-1 Parts List ----------------------------------------------------------------------------------------------- 9-2 LID ASSEMBLY -------------------------------------------------- 0619S20138 -------------------------- 10-1 Drawing ----------------------------------------------------------------------------------------------- 10-1 Parts List ---------------------------------------------------------------------------------------------- 10-2 PUSHER ASSEMBLY ------------------------------------------ 0619S20139-------------------------- 11-1 Drawing ----------------------------------------------------------------------------------------------- 11-1 Parts List ---------------------------------------------------------------------------------------------- 11-2 ELECTRICAL ASSEMBLY ------------------------------------ 0619S20140 -------------------------- 12-1 Drawing ----------------------------------------------------------------------------------------------- 12-1 Parts List ---------------------------------------------------------------------------------------------- 12-2 WARRANTY ------------------------------------------------------- GEN 040225 WARRANTY PROCEDURE------------------------------------ GEN 040226 RETURNED PARTS POLICY --------------------------------- GEN 040227

0619S20141 1-1

619-MDP DOUGH PRESS

SAFETY INSTRUCTIONS

Every effort has been made by Oliver Products Company to provide you with a safe machine. It is essential, however, that machine operators and maintenance personnel observe the following safety precautions. 1. Before attempting to operate your dough press read this manual. Never allow an

untrained person to operate this machine. 2. Make sure that the machine is only connected to a properly grounded electrical

supply source of sufficient capacity for the load the divider will put on it. Always unplug the machine when it is not in use.

3. Always make sure the machine has been disconnected and locked-out from the

power supply before cleaning or servicing. 4. All guards must be in place before starting the machine. 5. Keep your hands away from the moving parts of the machine. 6. Use only proper replacement parts. 7. Do not wear loose fitting clothing. Shirt tails should be tucked in. 8. In addition to these general safety instructions, also follow the more specific safety

instructions given for the different areas of the machine in the operating instructions.

0619S20130 2-1

619-MDP DOUGH PRESS

DESCRIPTION/SPECIFICATION

Description The Oliver dough press consists of a hopper which can be loaded with dough from an approximate minimum of ten and one half pounds up to forty pounds, (depending on the density of the dough). The lid and sides of the hopper are made of hard anodized and Teflon impregnated cast aluminum. The pressing plate located at the bottom of the hopper is manufactured of a food grade plastic and is raised by hydraulic pressure to compress the dough. This makes the machine ideal for puff and fine pastries and products requiring dough lamination. The hydraulic pump is powered by a two horsepower, totally enclosed motor. The system has a built-in four and one half gallon hydraulic oil tank making the machine totally self-contained and is provided with casters to allow for easy movement about the work area. Physical specifications

OVERALL MACHINE DIMENSIONS

0619S20130 2-2

Physical specifications (continued) Net Weight: Approximately 455 pounds. Shipping Weight: Approximately 500 pounds. Product Capacities: Fill Capacity (approximate) = 10-1/2 to 40 pounds Electrical Specifications 2 Horse Power, 1 phase, 60 hertz, 230 Volts AC, 10 Amps. 2 Horse Power, 3 phase, 60 hertz, 208 Volts AC, 6.5 Amps. 2 Horse Power, 3 phase, 60 hertz, 230 Volts AC, 6.2 Amps. 2 Horse Power, 3 phase, 60 hertz, 460 Volts AC, 3.1 Amps. Others consult factory

Electrical Wiring Diagrams 1 ph, 60 hz, 230 VAC

0619S20130 2-3

Electrical Wiring Diagrams (Continued)

3 ph, 60 hz, 208/230 VAC

3 ph, 60 hz, 460 VAC

0619S20131 3-1

619-MDP DOUGH PRESS

OPERATING INSTRUCTIONS

Before You Start

CAUTION THE DOUGH PRESS SHOULD ONLY BE PLUGGED INTO AN OUTLET WITH THE SAME VOLTAGE AS STATED ON THE NAMEPLATE Before starting a new dough press with THREE PHASE electrical power for the first time you should check to see if the motor is running in the correct direction. Remove the front cover by removing the four thumbscrews which secure it; you will also have to remove the handle from the directional control lever before removing the front cover. Once the cover has been removed you should be able to see the fan end of the motor on your dough press, this fan MUST rotate in a clockwise direction.

CAUTION EXTENDED RUNNING OF A DOUGH PRESS WITH THE MOTOR

ROTATING IN THE INCORRECT DIRECTION WILL SEVERELY DAMAGE THE HYDRAULIC PUMP OF YOUR MACHINE.

If the motor is rotating in the incorrect direction turn the machine off, disconnect it from the power supply and have a qualified electrician reverse two of the three power wires in the plug at the end of the power cord. DO NOT move the ground, (green), wire.

WARNING ALWAYS HAVE ELECTRICAL WORK DONE BY QUALIFIED ELECTRICIANS ONLY. Recheck the dough press making sure that it is now running in the correct direction, (clockwise looking at the fan end of the motor). Each time the machine is moved to a different power supply or has electrical work done which could alter the motor rotation, the motor must be rechecked for proper rotation. Basic Operation • Make sure the floor of the hopper has been lowered before attempting to open the lid

of the divider. • Open the lid and load the dough into the hopper. Spread the dough over the floor of

the hopper making it approximately the same height, this is done to eliminate large air pockets.

0619S20131 3-2

Basic Operation (Continued) • Close the lid and turn the handle in a clockwise direction making sure it is secure. • With the machine running grasp the control valve handle and lift it to start the floor of

the hopper up. Hold it in this position until the light on the starter switch box comes on, the light indicates that the preset pressing pressure has been achieved. Let loose of the valve handle when you see that the light is on.

• Press the control valve handle down slightly to release the pressure on the lid so it

can be opened. Open the lid. • The dough can now be removed and the above process repeated.

WARNING

NEVER LEAVE DOUGH IN A MACHINE WITHOUT OPENING THE LID; RISING DOUGH MAY CAUSE EXPLOSIVE PRESSURES TO DEVELOP.

WARNING

NEVER FORCE THE LID HANDLE OPEN

• If dough has been left in the machine and the lid handle is difficult to turn,

recompress the dough by lifting the control valve handle until the light come on. This will raise the floor of the hopper, after doing so lower the hopper floor by pressing down on the control valve handle. This may have to be done more than once if dough has been left in the machine for quite awhile. With the hopper floor all the way down try to open the lid again. The handle should turn easily, if it does not, recompress the dough and try again.

• The dough press is designed so that if dough is left in the hopper it will eventually

force the hopper’s floor to the bottom, thus allowing the dough to vent to the outside of the machine through openings on the left side. If dough is coming out of these openings follow the steps above, recompressing the dough a number of times before attempting to open the lid.

0619S20132 Rev 2/15/2010 4-1

619-MDP DOUGH PRESS

MAINTENANCE

WARNING

ALWAYS MAKE SURE THE MACHINE HAS BEEN DISCONNECTED FROM THE POWER SUPPLY BEFORE CLEANING OR SERVICING

Cleaning Remove- all scraps from lower pan. Open side doors and brushing out all scraps. Wash all interior surfaces; Knives, pusher plates, hopper, lid surface with a damp rag and mild soap solution. The exterior and contact surfaces should be cleaned daily using common cleaners. The knives should be extended for easier cleaning. This can be done by placing the cleaning separator, furnished with the machine, IN THE CENTER OF THE HOPPER straddling the knives. Close the lid and bring the floor of the hopper up until the light on the manual starter is on, lower the floor slightly. Open the lid and disconnect the divider from the power supply. Clean the knives and plastic compartment floors of all dough build-up. Rinse all interior surfaces with a damp rag and clean water. Sanitize all interior surfaces with a damp rag and sanitizing solution. Air Dry, leave divider lid open and allow interior to air dry before using. Occasionally, or as required, remove the front and rear covers to allow access to the drive chamber. There you should remove any build up of flour and dough particles in the base of the machine and from around the motor. When finished replace the covers. Lubrication The machine requires no lubrication but the oil level in the hydraulic system should be checked periodically. To check the oil level remove the rear cover by removing the four knobs which secure it to the divider, then remove the tank breather/cap and determine where the top of the oil is in relation to the top surface of the tank. Fill with oil to within approximately one inch of the top surface. If necessary add HYDRAULIC OIL to return it to the proper level, DO NOT OVERFILL. In addition to the above we advise replacing the hydraulic oil in the system approximately every three years. Hydraulic Oil Specification The hydraulic oil used in your divider should be made of good quality base stocks compounded with the following additives: anti-wear, anti-oxidation, antifoaming, and antirust. In addition it should be an “ISO” viscosity grade No. 32.

0619S20132 Rev 2/15/2010 4-2

Hydraulic Filter Replacement At least once a year the throw-away filter on the hydraulic system should be replaced, more often when under heavy use. To replace the filter disconnect the machine from the power supply, remove the front cover and unscrew the old filter. Replace it with a new one. The filter is located on the return line near the tank. After replacing the filter run the machine for five minutes and then check the oil level in the tank. See “Lubrication” above for how to check the oil level. Add oil if necessary to return it to the proper level. Removing The Lid • Remove the lid cover by removing the four screws which secure it in position. • Open the lid as far as it will go. • Release the tension on the two large torsion springs by moving the long leg of each

spring to the side and out from behind the bracket.

WARNING

USE CARE AS THE LID WILL DROP ONCE THE SPRING TENSION HAS BEEN REMOVED

• Close the lid and remove the right hand snap ring from the lid hinge pin and push the

pin to the left to remove it. • Reassemble by reversing the above steps. Replacing The Locking Hook Or Cam: • Remove the lid cover by removing the four screws which secure it in position. • Detach the spring from the hook. • Open the lid. • Turn the handle until the pin securing the cam to the shaft is in line with the notch in

the locking hook. Using a small drift punch force the pin upwards removing it from the handle shaft.

Replacing The Locking Hook Or Cam • Pull the shaft and cam assembly forward out of the lid. • The hook or locking cam can now be replaced. • Reassemble by reversing the above steps.

0619S20132 Rev 2/15/2010 4-3

Replacing A Pressing Plate • Open the lid and raise the bottom of the hopper. • Turn the machine off and disconnect it from the power supply. • Remove the front and rear panels to gain access to the pusher components. • Remove the sixteen screws securing the pressing plate to the backing plate. • Using a narrow block of wood or other soft material, force the pressing plate upwards

until it is free from the backing plate and then lift the pressing plate out of the cavity. • Reassemble by reversing the above steps. Removing the Backing Plate • Remove the Pressing Plate as described above. • Remove the bolt securing the backing plate to the cylinder rod. The backing plate

can now be lifted from the machine. • When the machine is re-assembled the bolt securing the backing plate to the cylinder

rod should be installed using “Loctite ®” adhesive to prevent loosening during operation. The remaining components can be reinstalled by reversing the above steps.

Replacing The Hydraulic Cylinder • Turn the machine on and raise the pressing plate to the top of the hopper and then

turn the dough press off and disconnect it from the power supply. • To remove the hydraulic cylinder the front, rear, and side panels must be removed

from the machine. • Remove the Pressing Plate and Backing Plate as described above. Replacing The Hydraulic Cylinder • Remove the bolts securing the starter switch bracket from the hex support rods, and

unplug the pressure switch wires. DO NOT disconnect the wires from the starter. • Remove one of the snap-rings securing the yoke and safety lock pivot pin. Remove

the pin so that the linkage can be unhooked from the top of the machine.

0619S20132 Rev 2/15/2010 4-4

Replacing The Hydraulic Cylinder • Remove the eight screws securing the cylinder to the cylinder mounting channel. • Remove the four bolts securing the cylinder mounting channel to the lower hex

support rods. • The upper portion of the divider can now be removed and set to one side. • Disconnect both high pressure hoses at the cylinder allowing removal of the cylinder

for repair or replacement. • When the machine is reassembled the bolt securing the backing plate to the cylinder

rod should be installed using “Loctite ®” thread locker to prevent loosening during operation. All other components can be reinstalled by reversing the above steps.

Removing The Motor • Disconnect the machine from the power supply. • Remove the front, rear and “Motor Side” panels. • Remove the four screws securing the pump bracket to the front of the motor. • Remove the four nuts securing the motor to the base of dough press. • Remove the terminal cover on the motor and disconnect the wiring, note the wire

locations to ease replacement of the motor. • The motor should now be free and can be removed by sliding the motor, with its half

of the coupling, out of the pump’s half of the coupling and lifting it free of the machine.

• Re-assemble by reversing the above steps. Changing The Pump Or Coupling • Disconnect the machine from the power supply. • Remove the rear cover and the “Motor Side” panels. • Loosen the intake hose at the pump, make sure you have something available to

catch the hydraulic oil leaking from the end of the hose when it is disconnected.

0619S20132 Rev 2/15/2010 4-5

Changing The Pump Or Coupling (Continued) • Remove the high pressure hose from the outlet side of the pump. • Remove the four bolts from the feet of the motor which secure it to the base this will

allow the motor to be pivoted slightly to allow pump removal. • Remove the bolts securing the pump to the bracket, pivot the motor and slide the

pump with its half of the coupling out and free of the motor. • Replace the pump by reversing the above procedures. Replacing The Control Valve • Remove the front and side panels from the divider. • Disconnect the three high pressure hoses from the control valve and remove the

filter head assembly form the machine. • Remove the lower pivot bolt from the lower end of the linkage connecting the valve

and the control handle. • Remove the three screws holding the valve to the valve mounting plate and remove

the valve from the divider. • Remove the remaining linkage parts from the old valve and re-install them on the

new valve. The new valve can then be installed in the divider by reversing the above procedures.

• Once the installation has been completed it IS necessary to adjust the pressure relief

valve to allow proper operation of the divider. To change the pressure relief setting, follow the step below.

• Looking at the pressure gauge attached to the pressure hose on the pump, with the

pump running, use the calibrating screw in the bottom of the valve to set the pressure at 650 PSIG secure the calibrating screw in place with the locking nut once the proper pressure has been achieved.

0619S20133 5-1

619-MDP DOUGH PRESS

TROUBLE SHOOTING GUIDE

The “Ram Up Light” does not come on. Possible Causes

• There may be a disconnected wire. • The pilot light may have burnt out. • The pressure switch is not operating and needs replacement.

The motor “Hums” but will not start. Possible Causes

• The motor is a dual voltage motor and may be wired for high voltage, but, an attempt is being made to run it on low voltage.

• The electric supply to the motor is single phase instead of three phase. • One of the leads of the three phase system has opened.

The motor runs but “Stalls” at either end of the cylinder’s travel. Possible Causes

• The incorrect overload relay was installed or the setting of that overload relay is incorrect.

• The setting of the hydraulic relief valve is too high.

• The motor is running backwards and needs its rotation corrected. See

“Before You Start” in the Operating Instructions.

0619S20133 5-2

The motor runs “Slowly” but stalls easily before completion of its stroke. Possible Causes

• The motor is wired for high voltage but is connected to a low voltage supply.

Trouble Shooting (Continued) The motor has “Stalled” and can not be restarted. Possible Causes

• The overload relay has tripped. Allow the relay about five minutes to cool and attempt to restart the divider.

The overload relay continually trips. Possible Causes

• An incorrect overload relay was installed or the setting of the overload relay is incorrect.

• There is an electrical problem in the machine have it checked by a qualified

electrician. The dough press is not pressing properly. Possible Causes

• Check the oil level in the tank, refill if necessary see “Lubrication” under maintenance.

• Check to see if the calibrating screw on the control valve has become loose.

If it has check the procedure for setting the pressure, given under “Replacing the Control Valve” in the maintenance section.

• The motor is running backwards and needs its rotation corrected. See

“Before You Start” in the Operating Instructions.

0619S20134 6-1

619-MDP DOUGH PRESS

RECOMMENDED SPARE PARTS

PART NUMBER PART DESCRIPTION NO. REQ’D. 7024-6101 Extension Spring 1 7030-0024 LH Lid Spring 1 7030-0023 RH Lid Spring 1 5835-7636 Coiled Pin 1 5114-9556 Hydraulic Filter 1 5757-8518 Pressure Switch 1 5709-9924 Starter Enclosure 1 5709-0191 Pilot Light 1 5709-3040 Motor Starter (3-60-460V) 1 5709-3041 Motor Starter (3-60-230V) 1 5709-3042 Motor Starter (3-60-208V) 1 5709-3043 Motor Starter (1-60-230V) 1

OPTIONAL SPARE PARTS 0620-0036 Handle Shaft 1 0620-0037-1 Latch Cam 1 0620-0017-3 Hook 1 0620-0067-1 Catch 1 0619-0018-002 Handle Rod 1 0619-0019-002 Hub 1 5911-7003 Handle Knob 1 5148-5624 Valve (Hydraulic) 1 5137-7004 Hydraulic Pump 1 5604-6958 Coupling 1 6303-6613 Motor 3 ph, 60 HZ, 208/230/460 VAC 1 6303-6725 Motor 1 ph, 60 HZ, 230VAC 1 Note: For Other electrics consult factory.

0619S20135 7-1

619-MDP DOUGH PRESS

MAIN FRAME

0619S20135 7-2

MAIN FRAME PARTS LIST

ITEM NO PART DESCRIPTION PART NUMBER 001 Base 0620-0008

002 Caster-Swivel 5902-2377

003 Caster-Rigid 5902-2378

008 Brace-Lower 0620-0006-001

009 Brace-Front Lower 0620-0006-002

012 Plate-Cylinder Support 0620-0007-001

014 Panel-Separation 0620-0032

015 Grommet-Edging Nylon 5767-1240

FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893

0619S20136 8-1

619-MDP DOUGH PRESS

COVER ASSEMBLY

0619S20136 8-2

COVER ASSEMBLY PARTS LIST

Stainless Steel Covers

ITEM NO PART DESCRIPTION PART NUMBER 101 Cover-Top 0620-0001-001

103 Handle-Pull 5908-5101

104 Plate-Backing 0619-0028

107 Cover-Side 0620-0029-002

109 Cover-Side W/Chute 0620-0029-005

110 Chute-Dough 0619-0027-008

111 Cover-Front 0620-0030-003

112 Screw-Thumb 5843-0536

114 Guard-Switch 0620-0106

117 Cover-Rear 0620-0031-001

118 Deflector 0619-0043

Painted Covers

101 Cover-Top 0620-0001

103 Handle-Pull 5908-5101

104 Plate-Backing 0619-0028

107 Cover-Side 0620-0029

109 Cover-Side W/Chute 0620-0029-004

110 Chute-Dough 0619-0027-008

111 Cover-Front 0620-0030

112 Screw-Thumb 5843-0536

114 Guard-Switch 0620-0106

117 Cover-Rear 0620-0031

118 Deflector 0619-0043

FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893

0619S20137 9-1

619-MDP DOUGH PRESS

HYDRAULIC ASSEMBLY

Rev. 10/25/05

0619S20137 9-2

HYDRAULIC ASSEMBLY PARTS LIST

ITEM NO PART DESCRIPTION PART NUMBER 201 Tank-Oil 0620-0069-002 206 Breather-Tank 5149-0204 207 Coupling-Black Pipe 5115-0332 208 Nipple-Black Pipe 6203-0407 209 Hose-Suction 0619-0016 210 Clamp-Heavy Duty Hose 5106-8087 211 Pump-Vane 2GPM 5137-7004 212 Flange-Pump Mounting 5137-7375 213 Fitting-Hose 5115-2079 214 Coupling-Pump 5604-6958 218 Gauge-Liquid Filled 5118-0506 219 Valve-4Way 5148-5624 223 Plate-Valve Mounting 0620-0027-001 226 Lever-Valve Actuating 0620-0026-001 227 Spacer 0620-0086 230 Rod-Valve Actuating 0620-0019-002 231 Clevis-Rod 0620-0020 232 Eye-Rod 0620-0021 234 Stirrup 0620-0015 235 Pin-Stirrup Pivot 0620-0025 236 Ring-Retaining 5840-1110 237 Lock-Safety 0620-0016 238 Pin 0620-0022 239 Rod-Handle 0620-0024-002 240 Knob 5911-7001 242 Cylinder-Hydraulic 5108-7665 243 Plate-Cylinder Alignment 0620-0120 246 Fitting-Adapter 5115-2093 247 Head-Filter 5114-9554 248 Filter-Spin-On 5114-9556 249 Fitting-Adapter 5115-4031 250 Fitting-Elbow 5115-4032 251 Tube-Return w/Flare 5147-0130 252 Flange-Tank 5115-0388 254 Valve-Pressure Relief 5148-6306 255 Fitting-Adapter 5115-2095 256 Switch-Pressure 5757-8518 258 Valve-Check 5148-5217 259 Spacer-Pump/Flange 0619-0044 Items Not Shown on Drawing 217 Hose-Pump High Pressure 5121-8235 241 Hose-Upper Cylinder 5121-8174 245 Hose-Valve to Lower Cylinder 5121-8187 257 Hose-Valve to Relief 5121-8196 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 Rev. 10/25/06

0619S20138 10-1

619-MDP DOUGH PRESS

LID ASSEMBLY

0619S20138 10-2

LID ASSEMBLY PARTS LIST

ITEM NO PART DESCRIPTION PART NUMBER 301 Lid-Square Hopper 0620-0018-001

302 Pin-Hinge 0620-0033

303 Spring-RH Torsion 7030-0023

304 Spring-LH Torsion 7030-0024

305 Ring-Retaining 5840-1127

306 Clamp-Spring 0620-0034

309 Shaft-Handle 0620-0036

310 Hook-Locking 0620-0017-3

311 Cam-Latch 0620-0037-1

312 Pin-Coiled 5835-7636

313 Screw-Socket Set (Oval Point) 5842-6479

319 Bracket-Spring 0620-0035

320 Spring-Extension 7024-6101

322 Hub 0619-0019-002

323 Rod-Handle 0619-0018-002

325 Knob 5911-7003

FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893

0619S20139 11-1

619-MDP DOUGH PRESS

PUSHER ASSEMBLY

0619S20139 11-2

PUSHER ASSEMBLY PARTS LIST

ITEM NO PART DESCRIPTION PART NUMBER 401 Plate-Hopper Front 0620-0059

402 Plate-Hopper Rear 0620-0060

403 Plate-Hopper Side 0620-0061

404 Plate-Hopper Side W/Relief 0620-0061-001

405 Pin-Dowel 5835-6266

409 Brace-Front Upper Adj. W/Holes 0620-0002-005

410 Brace-Front Upper Center Adj. 0620-0003-003

411 Brace-Upper Adj. 0620-0063-002

412 Hex Adjustable 0619-0026-001

417 Catch 0620-0067-1

418 Shim-(.030) 0619-0029-001

419 Shim-(.048) 0619-0029-002

420 Shim-(.060) 0619-0029-003

422 Plate-Backing 0620-0076

426 Plate Pressing 0620-0077

427 Insert-Threaded 5822-2030

FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893

0619S20140 12-1

619-MDP DOUGH PRESS

ELECTRICAL ASSEMBLY

0619S20140 12-2

ELECTRICAL ASSEMBLY PARTS LIST

ITEM NO PART DESCRIPTION PART NUMBER 801 Motor-2 HP (3-60-208/230/460) 6303-6613 801 Motor-2 HP (1-60-230) 6303-6725

806 Shockmount 5918-6636

809 Strain Relief-Motor 5765-1082

810 Strain Relief-Starter 5765-1124

811 Nut-Lock 5766-7750

815 Bracket-Starter 0620-0042-1

818 Light-Pilot 5709-0191

819 Starter Manual 3-60-230 5709-3041 819 Starter Manual 3-60-208 5709-3042 819 Starter Manual 3-60-460 5709-3040 819 Starter Manual 1-60-230 5709-3043

820 Enclosure-Starter 5709-9924

826 Strain Relief-Power Cord 5770-4818

Items Not Shown on Drawing 808 Cord-Motor (3-60-208/230) 0620-0073 808 Cord-Motor (3-60-460) 0620-0071-001 808 Cord-Motor (1-60-230) 0620-0038

825 Cord-Power (3-60-208/230) 0643-0033-001 825 Cord-Power (3-60-460) 0620-0105 825 Cord-Power (1-60-230) 0620-0039

827 Cord-Pressure Switch 0619-0042

828 Cap-Plug (1-60-230) 5765-2030

* For other Electrics consult factory FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893