mifare encoding from card studio using the zebra …...launch card studio and select card print from...

The right asset. In the right place. At the right time.

Mifare Encoding from Card Studiousing the Zebra Windows driver

Mifare Encoding using Card Studio

The following slides will present a basic way to encode Mifare cards using Card Studio.

You will need a Zebra printer with a Mifare encoder (printers with letter D or H in the part number -or upgraded with kit 105912G-134) and Card Studio Professional (Zebra # P 1031775-001).

The Zebra Mifare encoder uses a GEMALTO GEMPROX module.

It will encode Mifare cards 1K, 4K, DESFIRE, Type A and B

The following presentation is based on Card Studio Pro version 1.0

2

Launch Card Studio and select Card Print from the File menu. From the drop box menu, select your printer (Zebra driver- icon, not the ) . The dialogue box will close.


Leave the three boxes checked as shown.

3

Click on Properties


Check the SPOOL port is selected (in the Ports Tab) and, in the Encoders Tab, the card position is Contactless. Click OK when done or see next slide for the Tools Tab.

4

In the Tools Tab, you can perform some basic tests like moving the card to the encoding position,...Click Send to perform the command and OK to exit the menu.


5

Now select what you wish to perform with the printer: print front, back, both sides, Magnetic Encoding,..Please note Contactless Smart Card MUST be selected. Click on CLOSE, not on OK.


6

Select Card Setup from the Card Studio File drop menu and check the Contactless Chip selection. Click OK.


7

Click on the Contactless Icon.


This will open up the Data Map. Click on Card Setup.

8

Select the Gemalto Prox-Module.You may also select the key (A or B) and other parameters.Click on Apply, you will be returned to the Data Map screen (see page 8).


9

Now click on Encoding Setup. The Gemalto Prox-Module should be selected. You can test the communication between the PC and the Mifare encoder by clicking on Test Settings. Once completed click Finish.You are returned to the Data Map (see slide 8)


10

Select where you wish to encode your data (sector and block) by double-clicking on one line.


11

Select Data to Encode and enter your data. You can specify a Variable Source.Click on Data Placement and select a different location if you wish. Click on OK. You will be returned to the Data Map. Click on Close to go back to the card design screen.


12

Click on the Print Icon and click OK (or File/Card Print/OK) . The card will move to the Mifare station and will be encoded. The printer will perform the other operations (printing,...) after a successful Mifare encoding.


13

If something goes wrong during the encoding process, the system will re-try three times to encode. Afterwards, the following pop-up screen will appear.

Try to solve the issue (another card, re-check all the settings,...)

If still unsuccessful, see the next slide for technical support.

Encoding error

14

If you experience any issues when trying to encode, you can download the Zebra Test Software and test the functionality of the printer and encoder.

You can downloaded it from: http://www.zebra.com/cardpartner/index.php

For Technical Support, please use the following contacts:

For further assistance, contact:

Zebra Technologies Card Printer Solutions Dukes Meadow Millboard Road, Bourne End Buckinghamshire SL8 5XF, UK T: +44 (0) 1628 556 025 F: +44 (0) 1628 556 001 E: [email protected]

Reading an encoder card

German +49 (0)2159 676870 [email protected]

French +33 (0) 1 53 48 12 74 [email protected]

English +44 (0) 1628 556 225 [email protected]

15

mailto:[email protected]

mifare encoding from card studio using the zebra …...launch card studio and select card print from...

Documents