manual service laptop msi ex620

EX620 （MS-1674）Disassemble SOP

■ 1、Battery Pack

■ 2、BOTTOM DOOR ASSY

■ 3、THERMAL-KIT、CPU And VGA Card Module

■ 4、RAM、WLAN Module

■ 5、HDD Module ASSY

■ 6、ODD Module ASSY

■ 7、HINGE COVER ASSY

■ 8、UP CASE ASSY

■ 9、LOWER CASE ASSY

■ 10、LCD MODULE ASSY

EX620（MS-1674）Disassemble SOP

■ 1、Battery Pack

1-1：Push the battery lock button as below;

1-2：Push the battery Release button as below, then slide the battery pack out of the slot;

NO. Part Name Part No. Qty

1 Battery Pack S91-0300250-CE1 1


■ 2、BOTTOM DOOR ASSY

2-1：Remove 4pcs M2.5*5mm Screws; Note：Screw driver torque is 2.5-3.0kgf.cm

2-2：Remove Bottom Door Assy as below;


1 Screw E43-1255007-H29 4

2 BOTTOM DOOR ASSY 307-671J211-H76 1


■ 3、THERMAL-KIT、CPU And VGA Card Module

3-1：Remove 3pcs M2.5*5mm Screws and 4pcs Spring screws , Disconnect CPU Fan sink Cable. Note：Screw driver torque is 1.8-2.0kgf.cm

3-2：Remove CPU Fan sink;

2 6

3

1 4 7

5


1 screw E43-1255007-H29 3

2 HEATSINK E32-0900620-TA9 1


3-3： Open the CPU Socket as below;

3-4：Remove CPU Module;


1 CPU Module A09-2520196-I06 1

EX620（MS-1674）Disassemble SOP 3-5：Remove 1pcs M2.5*5mm Screw;

Note：Screw driver torque is 2.5-3.0kgf.cm

3-6：Remove VGA Card as below;


1 Screw E43-1255007-H29 1

2 VGA CARD 602-V122-14S 1


■ 4、RAM、WLAN Module

4-1：Push RAM Slot Fastener as below;

4-2：Remove RAM Module;


1 RAM Module S7C-S356802-T10 2


4-3：Remove WLAN Antenna, Then remove 1pcs M2*3mm Screw ; Note：Screw driver torque is 1.8～2.0kgf.cm

4-4：Remove WLAN Module;


1 WLAN Module S57-0800183-I06 1

2 Screw E43-1203003-H29 1


■ 5、HDD Module ASSY

5-1：Remove HDD Module as below;


5-2：Remove 2pcs M3*3.5mm Screws Then remove HDD Bracket as below; Note：Screw driver torque is 2.0~2.5kgf.cm


1 Screw E43-1303502-H29 2

2 HDD Bracket E2M-6710911-A89 1

3 HDD MODULE ASSY S71-2432503-T14 1


■ 6、ODD Module ASSY

6-1：Remove 1pcs M2.5*5mm Screw Then remove ODD Module Assy as below; Note：Screw driver torque is 2.5-3.0 kgf.cm


1 Screw E43-1255007-H29 1


6-2：Remove ODD Bezel as below;


1 ODD Bezel 307-671F411-H76 1


6-3：Remove 2pcs M2*3mm Screws Then remove ODD Braket as below; Note：Screw driver torque is 1.5~1.8kgf.cm


1 Screw E43-1203003-H29 2

2 ODD module S7D-2270001-SI4 1

3 ODD Braket E2M-6321111-Y28 1


■ 7、HINGE COVER ASSY

7-1：Push Fastener as below;

EX620（MS-1674）Disassemble SOP 7-2：Remove Hinge Cover as below;


1 HINGE COVER 307-674E411-H74 1

EX620（MS-1674）Disassemble SOP 7-3：Remove Sensor Board as below;


1 Sensor Board 607-1674D-C10 1

EX620（MS-1674）Disassemble SOP 7-4：Remove LCD LVDS Cable, MIC and CAMERA Cable as below;


1 Camera Cable K10-3005076-H39 1

2 LCD LVDS Cable K19-3040009-H39 1

EX620（MS-1674）Disassemble SOP 7-5：Pull cable out the slot as below;


7-6：Remove 4pcs M2.5*5mm screws as below; Note：Screw driver torque is 2.5-3.0kgf.cm


1 Screw E43-1255007-H29 4


7-7：Remove LCD MODULE ASSY as below;


■ 8、UPCASE ASSY

8-1：Remove 3pcs M2*3mm Screws, Then remove Keyboard as below; Note：Screw driver torque is 1.8-2.0kgf.cm


1 Screw E43-1203003-H29 3

2 Keyboard S11-00US140-C54 1


8-2：Remove PCI-E Card And XD Card as below;


1 PCI-E Card E2P-7212814-H76 1

2 XD Card E2P-7213611-H76 1


8-3：Remove Power Board ,Sensor Board, Touchpad, Finger printer, AUDIO board , Bluetooth CABLE as below;


1 Sensor board FFC K1C-1008002-J36 1

EX620（MS-1674）Disassemble SOP 8-4：Remove 14pcs M2.5*5mm Screws;



1 Screw E43-1255007-H29 14


8-5：Disconnect UP CASE and LOWER CASE as below;


8-6：Disconnect M/B and Up case as below;


1 UP CASE 307-674C422-TC7 1

2 M/B 607-16741-C10 1


8-7：Remove 2pcs M2*3mm Screws as below; Note：Screw driver torque is 1.5~2.0kgf.cm

8-8：Remove Launch Board FFC as below;


1 Screw E43-1203003-H29 2

2 Launch Board 607-1674B-C10 1

3 Launch Board FFC CABLE K1C-1016005-J36 1


8-9： Remove Bluetooth CABLE as below;

8-10：Remove BLUETOOTH MODULE and ANTENNA as below;


1 BLUETOOTH CABLE K10-3008069-H39 1

2 BLUETOOTH ANTENNA S79-1800280-H39 1

3 BLUETOOTH MODULE 605-6837D-070 1


8-11：Remove 3pcs M2*3mm Screws as below; Note：Screw driver torque is 1.5~1.8kgf.cm

8-12：Remove Touchpad Bracket as below;


1 Screw E43-1203003-H29 3

2 Touchpad_Bracket E2M-6740711-Y31 1


8-13：Remove 1pcs M2*3mm Screw , then remove Touchpad FFC (To M/B) as below; Note：Screw driver torque is 1.5~1.8kgf.cm


1 screw E43-1203003-H29 1

2 BUTTON Board 607-1674C-C10 1

3 FFC (To MB) K1C-1006022-J36 1


8-14：Remove Finger Printer , then remove FFC (To M/B) as below;


1 Finger Printer 607-1644C-01S 1

2 FFC (To MB) K1C-1006021-J36 1


8-15：Remove Touchpad Module as below;


1 FFC Cable(TO Button) K1C-1012029-J36 1

2 Touchpad Module S78-3700360-SD2 1


■ 9、LOWER CASE ASSY

9-1：Remove 2pcs M2.5*4mm screws as below; Note：Screw driver torque is 2.0~2.5kgf.cm


1 screw E45-1254001-H29 2

2 SPEAKER S33-S030100-F33 1

EX620（MS-1674）Disassemble SOP 9-2：Remove 2pcs M2*3mm screws as below;

Note：Screw driver torque is 1.5~2.0kgf.cm

9-3：Remove MDC Cable ,Then remove MODEM as below;


1 screw E43-1203003-H29 2

2 MODEM S52-2801170-Q09 1

3 MDC Cable K10-3002119-H39 1

EX620（MS-1674）Disassemble SOP 9-4：Remove Audio Cable(TO MB) and SPEAKER Cable as below;


1 AUDIO FFC Cable(TO M/B) K1C-1026018-J36 1

2 AUDIO board 607-1674A-C10 1


9-5：Remove 2pcs M2.5*5mm Screws, Then remove SPEAKER ,RJ11,TV IO JACK as below; Note：Screw driver torque is 2.0~2.5kgf.cm


1 Screw E43-1255007-H29 2

2 LOWER CASE 307-674D211-H76 1

3 SPEAKER S33-A020300-F33 1

4 RJ11 CABLE K10-3002119-H39 1

5 TV IO JACK K19-3001019-H39 1

EX620（MS-1674）Disassemble SOP ■ 10、LCD MODULE ASSY

10-1：Remove 8pcs LCD Rubbers Then Remove 4pcs M2.5*5mm Screws; Note：Screw driver torque is 2.5-3.0kgf.cm


1 LCD Rubber E2Y-6320931-Y40 8

2 Screw E43-1255007-H29 4


10-2：Remove LCD Bezel as below;


1 LCD BEZEL 307-674B411-H74 1


10-3：Remove 3pcs magnets as below;


1 MANGET E2y-2210512-SF7 2

2 MANGET E2Y-6710411-SF7 1

EX620（MS-1674）Disassemble SOP 10-4：Remove 4pcs M2.5*5mm Screws, Then remove Left And Right Hinge;



1 Screw E43-1255007-H29 4

2 Hinge_Left E2M-6710811-G60 1

3 Hinge_Right E2M-6710711-G60 1


10-5：Remove Inverter Module, Then remove Display Module;


1 Inverter S78-3300460-S49 1


10-6：Remove CMOS Camera Module as below;

Part Name Part No. Qty

1 CMOS Camera Module S1F-0003020-C54 1

2 Camera Cable K10-3005076-H39 1


10-7：Remove MIC Module as below;

Part Name Part No. Qty

1 MIC S34-2100730-N44 1


10-8：Remove 2pcs WLAN Antenna as below;


1 LCD Cover Assy 307-674A411-P89 1

2 Wireless Antenna_R S79-1800B20-V03 1

3 Wireless Antenna_L S79-1800B10-V03 1


10-9：Remove Coaxial Cable as below;


1 Coaxial Cable K19-3040009-H39 1

2 Display Module S1J-A42G001-S02 1


10-10：Remove 8pcs M2*3mm Screws, Then remove LCD Bracket as below; Note：Screw driver torque is 1.5~2.0kgf.cm


1 Screw E43-1203003-H29 8

2 LCD Bracket_L E2M-6740211-Y31 1

3 LCD Bracket_R E2M-6740111-Y31 1

EX620 （MS-1674）screws specification

Photo Screw specification Label

(M2.5*L5MM) black

(M2*L3MM)white

(M2.5*L4MM) black

(M3*L3.5MM) white

EX620 （MS-1674）screws specification ■ 1、BOTTOM DOOR ASSY total 15Pcs screws,

specification：

Photo Screw specification

label

(M2.5*L5MM) black

EX620 （MS-1674）screws specification ■ 2、THERMAL-KIT total 7pcs Screws

7

6

1

4

3 2

5

Photo Screw specification label

(M2.5*L5MM) black

EX620 （MS-1674）screws specification ■ 3、WIRELESS, VGA Card and HDD ASSY total 4Pcs screws

specification：


(M3*L3.5MM) white

(M2.5*L5MM) black

(M2*L3MM)white

EX620 （MS-1674）screws specification ■ 4.UPCASE ASSY total 9pcs screws,

specification：

Photo Screw specification Label

(M2*L3MM)white

(M2.5*L5MM) black

EX620 （MS-1674）screws specification ■ 5.LCD Bezel total 4pcs screws,

specification：


(M2.5*L5MM) black

EX620 （MS-1674）screws specification ■ 6. LCD MODULE ASSY total 12Pcs screws specification：


(M2*L3MM)white

(M2.5*L5MM) black

EX620 （MS-1674）screws specification ■ 7.Power board and LOWER CASE total 4Pcs screws，

specification：


(M2.5*L5MM) black

(M2*L3MM)white

EX620 （MS-1674）screws specification ■ 8、LOWER CASE total 6pcs screws specification：


(M2.5*L4MM) black

(M2.5*L5MM) black

(M2*L3MM) white

EX620 （MS-1674）screws specification ■ 9. Touch Pad Board total 3pcs screws

specification：


(M2*L3MM)white

manual service laptop msi ex620

Documents