Download - Manual service laptop MSI EX620
EX620 (MS-1674)Disassemble SOP
■ 1、Battery Pack
■ 2、BOTTOM DOOR ASSY
■ 3、THERMAL-KIT、CPU And VGA Card Module
■ 4、RAM、WLAN Module
■ 5、HDD Module ASSY
■ 6、ODD Module ASSY
■ 7、HINGE COVER ASSY
■ 8、UP CASE ASSY
■ 9、LOWER CASE ASSY
■ 10、LCD MODULE ASSY
EX620(MS-1674)Disassemble SOP
■ 1、Battery Pack
1-1:Push the battery lock button as below;
1-2:Push the battery Release button as below, then slide the battery pack out of the slot;
NO. Part Name Part No. Qty
1 Battery Pack S91-0300250-CE1 1
EX620(MS-1674)Disassemble SOP
■ 2、BOTTOM DOOR ASSY
2-1:Remove 4pcs M2.5*5mm Screws; Note:Screw driver torque is 2.5-3.0kgf.cm
2-2:Remove Bottom Door Assy as below;
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 4
2 BOTTOM DOOR ASSY 307-671J211-H76 1
EX620(MS-1674)Disassemble SOP
■ 3、THERMAL-KIT、CPU And VGA Card Module
3-1:Remove 3pcs M2.5*5mm Screws and 4pcs Spring screws , Disconnect CPU Fan sink Cable. Note:Screw driver torque is 1.8-2.0kgf.cm
3-2:Remove CPU Fan sink;
2 6
3
1 4 7
5
NO. Part Name Part No. Qty
1 screw E43-1255007-H29 3
2 HEATSINK E32-0900620-TA9 1
EX620(MS-1674)Disassemble SOP
3-3: Open the CPU Socket as below;
3-4:Remove CPU Module;
NO. Part Name Part No. Qty
1 CPU Module A09-2520196-I06 1
EX620(MS-1674)Disassemble SOP 3-5:Remove 1pcs M2.5*5mm Screw;
Note:Screw driver torque is 2.5-3.0kgf.cm
3-6:Remove VGA Card as below;
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 1
2 VGA CARD 602-V122-14S 1
EX620(MS-1674)Disassemble SOP
■ 4、RAM、WLAN Module
4-1:Push RAM Slot Fastener as below;
4-2:Remove RAM Module;
NO. Part Name Part No. Qty
1 RAM Module S7C-S356802-T10 2
EX620(MS-1674)Disassemble SOP
4-3:Remove WLAN Antenna, Then remove 1pcs M2*3mm Screw ; Note:Screw driver torque is 1.8~2.0kgf.cm
4-4:Remove WLAN Module;
NO. Part Name Part No. Qty
1 WLAN Module S57-0800183-I06 1
2 Screw E43-1203003-H29 1
EX620(MS-1674)Disassemble SOP
■ 5、HDD Module ASSY
5-1:Remove HDD Module as below;
EX620(MS-1674)Disassemble SOP
5-2:Remove 2pcs M3*3.5mm Screws Then remove HDD Bracket as below; Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1303502-H29 2
2 HDD Bracket E2M-6710911-A89 1
3 HDD MODULE ASSY S71-2432503-T14 1
EX620(MS-1674)Disassemble SOP
■ 6、ODD Module ASSY
6-1:Remove 1pcs M2.5*5mm Screw Then remove ODD Module Assy as below; Note:Screw driver torque is 2.5-3.0 kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 1
EX620(MS-1674)Disassemble SOP
6-2:Remove ODD Bezel as below;
NO. Part Name Part No. Qty
1 ODD Bezel 307-671F411-H76 1
EX620(MS-1674)Disassemble SOP
6-3:Remove 2pcs M2*3mm Screws Then remove ODD Braket as below; Note:Screw driver torque is 1.5~1.8kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 2
2 ODD module S7D-2270001-SI4 1
3 ODD Braket E2M-6321111-Y28 1
EX620(MS-1674)Disassemble SOP
■ 7、HINGE COVER ASSY
7-1:Push Fastener as below;
EX620(MS-1674)Disassemble SOP 7-2:Remove Hinge Cover as below;
NO. Part Name Part No. Qty
1 HINGE COVER 307-674E411-H74 1
EX620(MS-1674)Disassemble SOP 7-3:Remove Sensor Board as below;
NO. Part Name Part No. Qty
1 Sensor Board 607-1674D-C10 1
EX620(MS-1674)Disassemble SOP 7-4:Remove LCD LVDS Cable, MIC and CAMERA Cable as below;
NO. Part Name Part No. Qty
1 Camera Cable K10-3005076-H39 1
2 LCD LVDS Cable K19-3040009-H39 1
EX620(MS-1674)Disassemble SOP 7-5:Pull cable out the slot as below;
EX620(MS-1674)Disassemble SOP
7-6:Remove 4pcs M2.5*5mm screws as below; Note:Screw driver torque is 2.5-3.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 4
EX620(MS-1674)Disassemble SOP
7-7:Remove LCD MODULE ASSY as below;
EX620(MS-1674)Disassemble SOP
■ 8、UPCASE ASSY
8-1:Remove 3pcs M2*3mm Screws, Then remove Keyboard as below; Note:Screw driver torque is 1.8-2.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 3
2 Keyboard S11-00US140-C54 1
EX620(MS-1674)Disassemble SOP
8-2:Remove PCI-E Card And XD Card as below;
NO. Part Name Part No. Qty
1 PCI-E Card E2P-7212814-H76 1
2 XD Card E2P-7213611-H76 1
EX620(MS-1674)Disassemble SOP
8-3:Remove Power Board ,Sensor Board, Touchpad, Finger printer, AUDIO board , Bluetooth CABLE as below;
NO. Part Name Part No. Qty
1 Sensor board FFC K1C-1008002-J36 1
EX620(MS-1674)Disassemble SOP 8-4:Remove 14pcs M2.5*5mm Screws;
Note:Screw driver torque is 2.5-3.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 14
EX620(MS-1674)Disassemble SOP
8-5:Disconnect UP CASE and LOWER CASE as below;
EX620(MS-1674)Disassemble SOP
8-6:Disconnect M/B and Up case as below;
NO. Part Name Part No. Qty
1 UP CASE 307-674C422-TC7 1
2 M/B 607-16741-C10 1
EX620(MS-1674)Disassemble SOP
8-7:Remove 2pcs M2*3mm Screws as below; Note:Screw driver torque is 1.5~2.0kgf.cm
8-8:Remove Launch Board FFC as below;
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 2
2 Launch Board 607-1674B-C10 1
3 Launch Board FFC CABLE K1C-1016005-J36 1
EX620(MS-1674)Disassemble SOP
8-9: Remove Bluetooth CABLE as below;
8-10:Remove BLUETOOTH MODULE and ANTENNA as below;
NO. Part Name Part No. Qty
1 BLUETOOTH CABLE K10-3008069-H39 1
2 BLUETOOTH ANTENNA S79-1800280-H39 1
3 BLUETOOTH MODULE 605-6837D-070 1
EX620(MS-1674)Disassemble SOP
8-11:Remove 3pcs M2*3mm Screws as below; Note:Screw driver torque is 1.5~1.8kgf.cm
8-12:Remove Touchpad Bracket as below;
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 3
2 Touchpad_Bracket E2M-6740711-Y31 1
EX620(MS-1674)Disassemble SOP
8-13:Remove 1pcs M2*3mm Screw , then remove Touchpad FFC (To M/B) as below; Note:Screw driver torque is 1.5~1.8kgf.cm
NO. Part Name Part No. Qty
1 screw E43-1203003-H29 1
2 BUTTON Board 607-1674C-C10 1
3 FFC (To MB) K1C-1006022-J36 1
EX620(MS-1674)Disassemble SOP
8-14:Remove Finger Printer , then remove FFC (To M/B) as below;
NO. Part Name Part No. Qty
1 Finger Printer 607-1644C-01S 1
2 FFC (To MB) K1C-1006021-J36 1
EX620(MS-1674)Disassemble SOP
8-15:Remove Touchpad Module as below;
NO. Part Name Part No. Qty
1 FFC Cable(TO Button) K1C-1012029-J36 1
2 Touchpad Module S78-3700360-SD2 1
EX620(MS-1674)Disassemble SOP
■ 9、LOWER CASE ASSY
9-1:Remove 2pcs M2.5*4mm screws as below; Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 screw E45-1254001-H29 2
2 SPEAKER S33-S030100-F33 1
EX620(MS-1674)Disassemble SOP 9-2:Remove 2pcs M2*3mm screws as below;
Note:Screw driver torque is 1.5~2.0kgf.cm
9-3:Remove MDC Cable ,Then remove MODEM as below;
NO. Part Name Part No. Qty
1 screw E43-1203003-H29 2
2 MODEM S52-2801170-Q09 1
3 MDC Cable K10-3002119-H39 1
EX620(MS-1674)Disassemble SOP 9-4:Remove Audio Cable(TO MB) and SPEAKER Cable as below;
NO. Part Name Part No. Qty
1 AUDIO FFC Cable(TO M/B) K1C-1026018-J36 1
2 AUDIO board 607-1674A-C10 1
EX620(MS-1674)Disassemble SOP
9-5:Remove 2pcs M2.5*5mm Screws, Then remove SPEAKER ,RJ11,TV IO JACK as below; Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 2
2 LOWER CASE 307-674D211-H76 1
3 SPEAKER S33-A020300-F33 1
4 RJ11 CABLE K10-3002119-H39 1
5 TV IO JACK K19-3001019-H39 1
EX620(MS-1674)Disassemble SOP ■ 10、LCD MODULE ASSY
10-1:Remove 8pcs LCD Rubbers Then Remove 4pcs M2.5*5mm Screws; Note:Screw driver torque is 2.5-3.0kgf.cm
NO. Part Name Part No. Qty
1 LCD Rubber E2Y-6320931-Y40 8
2 Screw E43-1255007-H29 4
EX620(MS-1674)Disassemble SOP
10-2:Remove LCD Bezel as below;
NO. Part Name Part No. Qty
1 LCD BEZEL 307-674B411-H74 1
EX620(MS-1674)Disassemble SOP
10-3:Remove 3pcs magnets as below;
NO. Part Name Part No. Qty
1 MANGET E2y-2210512-SF7 2
2 MANGET E2Y-6710411-SF7 1
EX620(MS-1674)Disassemble SOP 10-4:Remove 4pcs M2.5*5mm Screws, Then remove Left And Right Hinge;
Note:Screw driver torque is 2.5-3.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255007-H29 4
2 Hinge_Left E2M-6710811-G60 1
3 Hinge_Right E2M-6710711-G60 1
EX620(MS-1674)Disassemble SOP
10-5:Remove Inverter Module, Then remove Display Module;
NO. Part Name Part No. Qty
1 Inverter S78-3300460-S49 1
EX620(MS-1674)Disassemble SOP
10-6:Remove CMOS Camera Module as below;
Part Name Part No. Qty
1 CMOS Camera Module S1F-0003020-C54 1
2 Camera Cable K10-3005076-H39 1
EX620(MS-1674)Disassemble SOP
10-7:Remove MIC Module as below;
Part Name Part No. Qty
1 MIC S34-2100730-N44 1
EX620(MS-1674)Disassemble SOP
10-8:Remove 2pcs WLAN Antenna as below;
NO. Part Name Part No. Qty
1 LCD Cover Assy 307-674A411-P89 1
2 Wireless Antenna_R S79-1800B20-V03 1
3 Wireless Antenna_L S79-1800B10-V03 1
EX620(MS-1674)Disassemble SOP
10-9:Remove Coaxial Cable as below;
NO. Part Name Part No. Qty
1 Coaxial Cable K19-3040009-H39 1
2 Display Module S1J-A42G001-S02 1
EX620(MS-1674)Disassemble SOP
10-10:Remove 8pcs M2*3mm Screws, Then remove LCD Bracket as below; Note:Screw driver torque is 1.5~2.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 8
2 LCD Bracket_L E2M-6740211-Y31 1
3 LCD Bracket_R E2M-6740111-Y31 1
EX620 (MS-1674)screws specification
Photo Screw specification Label
(M2.5*L5MM) black
(M2*L3MM)white
(M2.5*L4MM) black
(M3*L3.5MM) white
EX620 (MS-1674)screws specification ■ 1、BOTTOM DOOR ASSY total 15Pcs screws,
specification:
Photo Screw specification
label
(M2.5*L5MM) black
EX620 (MS-1674)screws specification ■ 2、THERMAL-KIT total 7pcs Screws
7
6
1
4
3 2
5
Photo Screw specification label
(M2.5*L5MM) black
EX620 (MS-1674)screws specification ■ 3、WIRELESS, VGA Card and HDD ASSY total 4Pcs screws
specification:
Photo Screw specification label
(M3*L3.5MM) white
(M2.5*L5MM) black
(M2*L3MM)white
EX620 (MS-1674)screws specification ■ 4.UPCASE ASSY total 9pcs screws,
specification:
Photo Screw specification Label
(M2*L3MM)white
(M2.5*L5MM) black
EX620 (MS-1674)screws specification ■ 5.LCD Bezel total 4pcs screws,
specification:
Photo Screw specification label
(M2.5*L5MM) black
EX620 (MS-1674)screws specification ■ 6. LCD MODULE ASSY total 12Pcs screws specification:
Photo Screw specification label
(M2*L3MM)white
(M2.5*L5MM) black
EX620 (MS-1674)screws specification ■ 7.Power board and LOWER CASE total 4Pcs screws,
specification:
Photo Screw specification label
(M2.5*L5MM) black
(M2*L3MM)white
EX620 (MS-1674)screws specification ■ 8、LOWER CASE total 6pcs screws specification:
Photo Screw specification label
(M2.5*L4MM) black
(M2.5*L5MM) black
(M2*L3MM) white
EX620 (MS-1674)screws specification ■ 9. Touch Pad Board total 3pcs screws
specification:
Photo Screw specification label
(M2*L3MM)white