manual power monitor nsc

Publication 1403-5.1

Smart Communications Card(Cat. No. 1403-NSC)

Important User Information

Solid-state equipment has operational characteristicsdiffering from those of electromechanical equipment.Safety Guidelines for the Application, Installation, andMaintenance of Solid-state Controllers (PublicationSGI-1.1) describes some important differences betweensolid-state equipment and hard-wired electromechanicaldevices. Because of this difference, and also because ofthe wide variety of uses for solid-state equipment, allpersons responsible for applying this equipment mustsatisfy themselves that each intended application of thisequipment is acceptable.

In no event will the Allen-Bradley Company, Inc. beresponsible for indirect or consequential damagesresulting from the use or application of this equipment.

The examples and diagrams in this manual are includedsolely for illustrative purposes. Because of the manyvariables and requirements associated with any particularinstallation, the Allen-Bradley Company, Inc. cannotassume responsibility or liability for actual use based onthe examples and diagrams.

No patent liability is assumed by the Allen-BradleyCompany, Inc. with respect to use of information,circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole orin part, without written permission of Allen-BradleyCompany, Inc., is prohibited.

Throughout this manual we use notes to make you awareof safety considerations:

!ATTENTION: Identifies informationabout practices or circumstances that canlead to personal injury or death, propertydamage or economic loss.

Attention statements help you to:

• identify a hazard

• avoid the hazard

• recognize the consequences

Important: Identifies information that is critical forsuccessful application and understandingof the product.

Terms and Conventions

In this instruction sheet, the following terms andconventions are used:

Abbreviation Term

BTR Block Transfer Read

BTW Block Transfer Write

MSG Message

Table of Contents

Product Description 2. . . . . . . . . . . . . . . . . . . . . Installation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . General Operation 8. . . . . . . . . . . . . . . . . . . . . . Catalog Number Explanation App. A. . . . . . . . . . . . . . Smart Communication Card Data Tables App. B. . . . . . Smart Communication Protocol Tutorial App. C. . . . . . . Sample Ladder Listing App. D. . . . . . . . . . . . . . . . . . . Technical Specifications App. E. . . . . . . . . . . . . . . . . .

PLC is a registered trademark of Allen-Bradley Company, Inc.Data Highway Plus and SLC are trademarks of Allen-Bradley Company, Inc.

Instruction Sheet

Smart Communications Card 2


Product Description

Chapter Objectives

After completing this chapter, you should be able toidentify the product features and system applications.

Introduction

The Cat. No. 1403-NSC Smart Communications Card isa microprocessor-controlled dual-port communicationplug-in accessory to the Powermonitor II Master Module.This accessory provides the Powermonitor II with twoactive communication ports which can be used at thesame time. Required configuration parameters (R I/Orack address, baud rates, etc.) are provided byconfiguring the Master Module. One port is dedicated tothe Allen-Bradley PLC R I/O network and the otherport is software configurable for either EIA StandardsRS-232C or RS-485. (There are no hardware options toconfigure when the card is installed.)

Performance Features

The Smart Communication Card performance featuresinclude:

• PLC via R I/O

• SLC 500 via R I/O with (1747-SN) Series B or laterscanner module

• SLC 500 via DF-1 master slave protocol

• R I/O Baud rates: 57.6K baud-230K baud

• Serial Baud rates: 1,200–19,200 baud

• Simultaneous R I/O and serial communication

• 124 units per subnet, 255 per network via RS-485

• 500 V isolation on communications ports

• Fully software configurable, no hardware jumpersrequired

Figure 1. Cat. No 1403-NSC Communications Module

Serial Transmit (TXD) LED

Serial Receive (RXD) LED

Finger hold

Captive fastening screwConnectorR I/O Active LED

3Smart Communications Card


Installation

!ATTENTION: Please followappropriate ESD procedures beforeremoval and/or installation of the SmartCommunications Card. Failure to followthese procedures can result in physicaldamage to both the SmartCommunications Card and the MasterModule.

1. To remove the blank plate on the Master Module,unscrew the two corner retaining screws as shown inFigure 2. Save these two screws for reassembly.

Figure 2.

2. If you plan to remove the communications card at alater date, retain the blank plate. Otherwise, disposeof properly.

3. Remove the communications card from the staticprotection shipping bag.

4. Grasp the card with the components side up and thethree LEDs on the left. Place the right index finger inthe top notch and the thumb in the bottom notch.

5. With the Master Module labels right side up, placethe card into opening on the left side. The card toMaster Module connector should align properly whenthe top right and bottom left guide pins of the MasterModule mate with holes in the card. With your leftthumb, press just above the card to Master Moduleconnector to attach the connector. Tighten the fourcorner screws.

Figure 3.

6. Place the closure plate over the opening and secure itwith the two screws from the original blank plate.

Figure 4.

Note: Refer to Appendix E, Specifications for screwtorque requirements and wire sizes.



Wiring

!ATTENTION: Special high levelisolation is required between units whenthe possibility of high ground potentialdifferences exist. This may occur whenseparate grounds are used or whencommunicating to a unit connected to apower ground mat. Failure to do so canlead to personal injury or death, propertydamage, or economic loss.

Table A. Wiring Connections

Connector

CommunicationFormat

Terminal #(Countingfrom the

bottom up)

TerminalLabel

Intended Use, Pin Connection,or Wire Color

RecommendedCable Type

Maximum CableLength/Baud Rate

12 Do not connect

11 Do not connect

10 SHLD Cable shield grounding point2 ire shieldedRS-485 9 – Minus signal data 2-wire shielded(Belden 9841)

4000 ft/19.2kBRS 4858 + Plus signal data

(Belden 9841) 4000 ft/19.2kB

7 RXDPC Transmit, DB25, pin 2, (DB9, pin 3)

RS-2326 TXD PC Receive, DB25, pin3 (DB9, pin 2) 3-wire Shielded 50 ft/19 2kBRS-2325 SG

PC signal return, DB25, pin 7 (DB9, pin 5)

3-wire Shielded(Belden 9608) 50 ft/19.2kB

4 SHLD Cable Shield

3 1 Blue Wire insulation 1770-CDT i i l 10,000 ft /57.6kBaud

R-I/O 2 SHLD Cable shield ground point

1770 CDTwinaxial

(Blue Hose)

10,000 ft /57.6kBaud5,000 ft/115.2kBaud2 500 ft/230 4kB d

R I/O

1 2 Clear wire insulation(Blue Hose)

(Belden 9463)

5,000 ft/115.2kBaud2,500 ft/230.4kBaud

Notes:

1. The communications topology for both R I/O andRS-485 is designed to operate in a daisy-chaintopology. Use of the star or bridging method willcause signal distortion unless impedances arematched for each spur. Bridging is not recommendedwithout matching networks.

2. To prevent end reflections, each end of the daisy-chain should be terminated in the characteristicimpedance for the cable, the baud rate, and frequencyused.

CommunicationFormat

Baud RateTerminating

Resistor

RS-485 1200–19.2k 150 Ω 1/4 W

R I/O57.6–115.2k 150 Ω 1/4 W

R I/O230.4k 84 Ω 1/4 W

3. Each end section of cable should have the shieldconnected to the terminal labeled SHLD. This SHLDground provides a high frequency ground, whilelimiting DC or power line frequencies from flowingdown the cable shield.

4. The RS-485 receivers in the communications cardprovide a 1/4 load impedance instead of the normalfull load impedance. This therefore allows the use offour times the number of receivers (32 4 or 128total) on one network.



Figure 5. R I/O Wiring

BLUE

SHIELD

CLEAR

PLC PROCESSOR

INTERNAL TERMINATING

150Ω RESISTOR

84Ω OR 150Ω RESISTOR

Powermonitor II

DEVICE #1

Powermonitor II

DEVICE #2

Powermonitor II

DEVICE #3

0.047uF

150KΩ

0.047uF

150KΩ

0.047uF

150KΩ

Note: All ground wires should be kept as short aspossible between the R/C and the cover plate.



Figure 6. RS-485 Wiring

150Ω RESISTOR

Powermonitor II

DEVICE #1

Powermonitor II

DEVICE #2

Powermonitor II

DEVICE #3

EXTERNAL

RS–232C TO RS–485

CONVERTER

IBM PC

PLC PROCESSOR

RS–232C

150Ω RESISTOR

0.047uF

150KΩ

0.047uF

150KΩ

0.047uF

150KΩ

Note: All ground wires should be kept as short aspossible between the R/C and the cover plate.



Figure 7. RS-232C Wiring

IBM PC

PLC PROCESSOR

1

3

2

7

CASE

GROUND

2

3

5

25 PIN

D–SHELL

9 PIN

D–SHELL

Powermonitor II

Note: For CE compliance, the communication cable shield mustbe connected directly to the chassis ground terminallocated on the communication card cover plate. Theexposed shield wire should be as short as possible.

Field Service Considerations

If the Smart Communications Card requires service,please contact your nearest Allen-Bradley Sales Office.To minimize your inconvenience, the initial installationshould be performed in a manner which makesremoval easy.



General Operation

Communications Card Set-Up

All communications card options such ascommunications format, baud rate, address, etc., are setby configuring the Master Module. Refer toPowermonitor II Instruction Sheet, Publication 1403-5.0,Chapter 4.

Indicators

Figure 1. on page 2 shows the location of the LEDIndicators on the communications card.

Table B. LED Indicators

LEDLocation

LEDColor

Port Assignment LED State and Communications Condition

Top Red RS-232 or RS-485 ReceiveOFF = IdleON/OFF Pulsing = Receiving Data

Middle Red RS-232 or RS-485 TransmitOFF = IdleON/OFF Pulsing = Transmitting Data

Bottom Green R I/OON = Communications EstablishedON/OFF Blinking = Communications Established With Some ErrorsOFF = Communications Not Established

Configuration Items

Communication

Table C. Communication Configuration Items

Parameter Description Range DefaultUser

Setting

R I/O Rack AddressSpecifies the logical rack of the Smart CommunicationCard.

0 to 63 1

R I/O Group Number Determines the group number of the logical rack.

0 = First Quarter2 = Second Quarter4 = Third Quarter6 = Fourth Quarter

0 = FirstQuarter

R I/O Last RackDefines whether or not the configured rack is the lastrack.

0 = No1 = Yes

0 = No

R I/O Baud Rate Specifies the baud rate of the RIO network.0 to 56K1 to 115K2 to 230K

0 to 56K

Serial DelayDefines the delay in ms between the request andresponse serial packets.

0 to 15 0

Serial Mode Specifies the serial communications mode.0 = RS-4851 = RS-232

1 = RS-232

RS-232/RS-485 BaudRate

Determines the baud rate for the serial communications.

0 to 12001 to 24002 to 48003 to 96004 to 19200

3 to 9600

Serial Device IdentifierDefines the specific serial address. A value of 255 isused as a broadcast address.

0 to 254 Device ID#

Appendix A


Catalog Number Explanation

Communications Cards

1403 - NSC

Bulletin Number Type of Device

Power Quality andAutomation Products

1403 = Plug-in Communications Card for Bulletin 1403-MM Devices(RS-232C / RS-485 / Allen-Bradley R I/O Protocols)

NSC =

A–2 Catalog Number Explanation


Appendix B


Smart Communication Card Data Tables

Table B.1 Data Table List

Table Name Number of Parameters

ID/Numberof Words Type of Table Page

Device Configuration Data Table 32 44 Block Transfer Read/Write

B–2

Smart Communication Card Data Table 21 30 Block Transfer Read/Write

B–4

Command Data Table 12 22 Block Transfer Write B–5

Bit Fields for Command Data Table (Command Word 1)

— — — B–6

Bit Fields for Command Data Table(Command Word 2)

— — — B–6

Voltage/Current Data 23 53 Block Transfer Read B–6

Real Time Power Data 25 62 Block Transfer Read B–7

Cumulative Power Data 7 45 Block Transfer Read B–9

Demand Data 18 42 Block Transfer Read B–10

Event Log 12 23 Block Transfer Read B–11

Voltage/Current/Miscellaneous Snapshot LogData Table

28 54 Block Transfer Read B–12

Power Snapshot Log Data Table 30 59 Block Transfer Read B–13

Min_Max Log 8 24 Block Transfer Read B–15

Log Selection Command Table 4 9 Block Transfer Write B–16

Available Min/Max Log Parameters 84 — — B–17

Even Harmonic Distortion Table 29 60 Block Transfer Read B–18

Odd Harmonic Distortion Table 29 61 Block Transfer Read B–19

Even Harmonic Magnitude Data Table 29 58 Block Transfer Read B–21

Odd Harmonic Magnitude Data Table 29 57 Block Transfer Read B–22

Even Harmonic Phase Angle Data Table 29 56 Block Transfer Read B–24

Odd Harmonic Phase Angle Data Table 29 55 Block Transfer Read B–25

Oscillogram Capture Data 54 63 Block Transfer Read B–27

Diagnostic Data Table (Self-test Results) 35 39 Block Transfer Read B–29

Setpoint Setup Data Table 9 20 Block Transfer Read/ B–30Setpoint Setup Data Table 9 20 Block Transfer Read/Write

B–30

Setpoint Type — — — B–31

Setpoint Action — — — B–31

Relay/Setpoint Status Table 29 38 Block Transfer Read B–32

Status Inputs Bitfield Definitions 16 bits — — B–33

Alarm Word Bitfield Definitions 16 bits — — B–33

Setpoint Status Bitfield Definitions 16 bits — — B–33

B–2 Smart Communication Card Data Tables


Table B.2 Device Configuration Data Table – Write and Read

ÁÁÁÁÁÁÁÁÁÁ

ParameterNo.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter Name ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Master Module Range ÁÁÁÁÁÁÁÁ

DefaultSettingÁÁÁÁÁÁÁÁÁÁ

Word No.ÁÁÁÁÁÁÁÁÁÁÁÁ

Range

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.1

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Voltage Mode

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = Demo1 = Single2 = Open Delta3 = 3-Wire Delta4 = 4-Wire Wye5 = Direct Delta

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

4


1

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 5

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Present Unit PasswordÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–1 is always returned on a Read 0 to 9999 is required for a Write

ÁÁÁÁÁÁÁÁÁÁÁÁ

0ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–1 to +9999


1.3 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

New Password ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–1 does not change the password 0 to 9999 is new password value

ÁÁÁÁÁÁÁÁ

0 ÁÁÁÁÁÁÁÁÁÁ

3 ÁÁÁÁÁÁÁÁÁÁÁÁ

–1 to +9999



Voltage Scale ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ120 0



0 to 9999ÁÁÁÁÁÁÁÁÁÁ


PT Primary ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.0 to 10,000,000.0 ÁÁÁÁÁÁÁÁ

120.0ÁÁÁÁÁÁÁÁÁÁ


10±0 to 21



Voltage Scale ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

PT Secondary ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 to 999 ÁÁÁÁÁÁÁÁ

120ÁÁÁÁÁÁÁÁÁÁ


1 to 999



Current Scale (For I1, I2, I3) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ

1 or 5➀ÁÁÁÁÁÁÁÁÁÁ


0 to 9999

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁCT Primary ÁÁÁÁÁÁÁÁÁ1.0 to 10,000,000.0 ÁÁÁÁ1 or 5➀

ÁÁÁÁÁ8 ÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁÁÁÁÁÁ1.7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCurrent Scale (For I1, I2, I3)


ÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCT Secondary

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ1 to 999

ÁÁÁÁÁÁÁÁ1 or 5➀

ÁÁÁÁÁÁÁÁÁÁ9

ÁÁÁÁÁÁÁÁÁÁÁÁ1 to 999ÁÁÁÁÁ

ÁÁÁÁÁ1.8


Analog Input ScaleÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ1 0


10ÁÁÁÁÁÁÁÁÁÁÁÁ



PT Primary ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.0 to 10,000,000.0 ÁÁÁÁÁÁÁÁ

1.0ÁÁÁÁÁÁÁÁÁÁ


10±0 to 21



Analog Input Scale ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ




PT Secondary ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 to 999 ÁÁÁÁÁÁÁÁ



1 to 999



Neutral Current Scale (For I4) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ

1 or 5➀ÁÁÁÁÁÁÁÁÁÁ


0 to 9999



CT Primary ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.0 to 10,000,000.0 ÁÁÁÁÁÁÁÁ

1 or 5➀



10±0 to 21ÁÁÁÁÁÁÁÁÁÁ1.11

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁNeutral Current Scale (For I4)


ÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCT Secondary


ÁÁÁÁÁÁÁÁ1 or 5➀



ÁÁÁÁÁ1.12


Demand Period LengthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–99 to +99ÁÁÁÁÁÁÁÁ



–99 to +99ÁÁÁÁÁÁÁÁÁÁ

1.13ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Number of Demand PeriodsÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 to 15ÁÁÁÁÁÁÁÁ





Reserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ


18 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁ1.15 ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁSnapshot Interval – Hours ÁÁÁÁÁÁÁÁÁ




0 to 32,767



Snapshot Interval – Minutes ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ



0 to 32,767



Snapshot Interval – Seconds ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ



0 to 32,767



Snapshot Buffer Type ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = Fill and Stop1 = Circular

ÁÁÁÁÁÁÁÁ



0 to 1




ÁÁÁÁÁÁÁÁ





ÁÁÁÁÁÁÁÁ





ÁÁÁÁÁÁÁÁ





ÁÁÁÁÁÁÁÁ



B–3Smart Communication Card Data Tables



ParameterNo.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter Name ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Master Module Range ÁÁÁÁÁÁ

DefaultSettingÁÁÁÁÁÁÁÁÁÁÁÁ

Word No. ÁÁÁÁÁÁÁÁÁÁ

RangeÁÁÁÁÁÁÁÁÁÁ


Reserved WordÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁ




1.19

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Output Pulse Relay No.


0 = None1 = Relay 12 = Relay 2

ÁÁÁÁÁÁÁÁÁ

0


28


0 to 2


1.20

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Output Pulse Parameter

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = kWh Forward1 = kWh Reverse2 = kVarh Forward3 = kVarh Reverse


0

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

29


0 to 3



Output Pulse Increment ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 to 32766 ÁÁÁÁÁÁ





Output Pulse Width (ms) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

40 to 2000 ÁÁÁÁÁÁ



40 to 2000


1.23

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Ch A 12 Cycle Oscillogram

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 = Phase 1 Voltage2 = Phase 1 Current3 = Phase 2 Voltage4 = Phase 2 Current5 = Phase 3 Voltage6 = Phase 3 Current7 = Phase 4 Current


1


32


1 to 7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.24

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Ch B 12 Cycle Oscillogram

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 = Phase 1 Voltage2 = Phase 1 Current3 = Phase 2 Voltage4 = Phase 2 Current5 = Phase 3 Voltage6 = Phase 3 Current7 = Phase 4 Current

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

2

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

33


1 to 7



Oscillography Type ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = Hold1 = Overwrite

ÁÁÁÁÁÁ



0 to 1



Number of Pretrigger Cycles forthe 12 Cycle Oscillogram


–1 = No Pretrig 0 to +8 = Cycles

ÁÁÁÁÁÁÁÁÁ



–1 to +8



IEEE 519 Max. Short CircuitCurrent


ÁÁÁÁÁÁ0ÁÁÁÁÁÁÁÁÁÁÁÁ


0 to 9999




0.0 to 10,000,000.0 ÁÁÁÁÁÁ



10±0 to 21



IEEE 519 Max. Demand/LoadCurrent


ÁÁÁÁÁÁÁÁÁ

0





ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0.0 to 10,000,000.0

ÁÁÁÁÁÁ

0 ÁÁÁÁÁÁÁÁÁÁÁÁ39

ÁÁÁÁÁÁÁÁÁÁ10±0 to 21



Save Status Changes to EventLog


0 = No1 = Yes

ÁÁÁÁÁÁÁÁÁ



0 to 1


1.30ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Vaux Voltage ModeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = AC1 = DC

ÁÁÁÁÁÁ



0 to 1ÁÁÁÁÁÁÁÁÁÁ1.31

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁEnable THD

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 or 1

ÁÁÁÁÁÁ1ÁÁÁÁÁÁÁÁÁÁÁÁ42

ÁÁÁÁÁÁÁÁÁÁ0 to 1ÁÁÁÁÁ



Enable Min_Max LogÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = No1 = Yes

ÁÁÁÁÁÁÁÁÁ



0 to 1



Data Format ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = Integer/Exponent1 = Floating Point

ÁÁÁÁÁÁ



0 to 1

➀ This value will be 1 for 1 Amp Master Module (Cat. No. 1403-MM01X) or 5 for a 5 Amp Master Module (Cat. No. 1403-MM05X).



Table B.3 Smart Communication Card Data Table – Write and Read

Note: The device will not respond to a broadcast of this table.


ParameterNo.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter Name ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Master Module Range ÁÁÁÁÁÁÁÁÁÁ

PLC Word No.ÁÁÁÁÁÁÁÁÁÁ


2.1ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

R I/O Rack AddressÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





R I/O Group NumberÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 6ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

2.3ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

R I/O Last RackÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = No – Default1 = Yes



0 to 1



R I/O Baud RateÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = 56K – Default1 = 115K2 = 230K



0 to 2


2.5 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Serial Response Delay ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 15 ÁÁÁÁÁÁÁÁÁÁ


0 to 15



Serial Type Specifier RS-232 or RS-485 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = RS-4851 = RS-232 – Default



0 to 1


2.7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SCC RS-232/RS-485 Baud Rate

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = 12001 = 24002 = 48003 = 9600 – Default4 = 19200


7


0 to 4

ÁÁÁÁÁÁÁÁÁÁ2.8

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSerial Device Identifier

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 255





R I/O Port Data FormatÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




0 to 1



Serial Port Data FormatÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




0 to 1ÁÁÁÁÁÁÁÁÁÁ2.11

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved




ÁÁÁÁÁ2.12


ReservedÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁ2.13





ÁÁÁÁÁ2.14 ÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁReserved ÁÁÁÁÁÁÁÁÁÁÁ


14 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ






















ÁÁÁÁÁ2.20ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved






Present Unit PasswordÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–1 is always returned for a Read0 to 9999 is required for a Write



–1 to +9999



Reserved ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
















ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved






















Table B.4 Command Data Table Write

ÁÁÁÁÁParameter No.ÁÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No. ÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁ3.1

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCommand Word 1 (Bit Fields)




ÁÁÁÁÁ3.2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Command Word 2 (Bit Fields)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 511ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

3.3

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Harmonic Analysis➀

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 = L1 Voltage2 = L1 Current3 = L2 Voltage4 = L2 Current5 = L3 Voltage6 = L3 Current7 = L4 Current


3


1 to 7


3.4

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Oscillogram Channel Request➀(Reserved 1403-LM)

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 = L1 Voltage2 = L1 Current3 = L2 Voltage4 = L2 Current5 = L3 Voltage6 = L3 Current7 = L4 Current8 = Ch–A 12 Cycle9 = Ch–B 12 Cycle


4


1 to 9

ÁÁÁÁÁ3.5 ÁÁÁÁÁÁÁÁÁÁÁW Hour Data for Set Command➀ ÁÁÁÁÁÁÁÁÁÁÁ–9999x108 to +9999x108 ÁÁÁÁÁ5 ÁÁÁÁÁ–9999 to 9999ÁÁÁÁÁÁÁÁÁÁ






ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVAR Hour Data for Set Command➀

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–9999x108 to +9999x108


ÁÁÁÁÁÁÁÁÁÁ–9999 to 9999ÁÁÁÁÁ





10±0 to 21













Time for Set Command➀ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

YearÁÁÁÁÁÁÁÁÁÁ


0–99 16 Bit IntegerÁÁÁÁÁ


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Month, Day


12

ÁÁÁÁÁÁÁÁÁ

1–128 Bit

ÁÁÁÁÁÁÁÁÁ

1–318 Bit




Hour, MinutesÁÁÁÁÁÁÁÁÁÁ

13ÁÁÁÁÁÁ

0–238 BitÁÁÁÁÁÁ

0–598 BitÁÁÁÁÁ




Seconds, Hundredths


14

ÁÁÁÁÁÁÁÁÁ

0–598 Bit

ÁÁÁÁÁÁÁÁÁ

0–998 Bit



Force Specifics Relay 1➀


1 = Energize2 = De-energize4 = Remove Force



1, 2, 4


3.10


Force Specifics Relay 2➀


1 = Energize2 = De-energize4 = Remove Force


16


1, 2, 4



Setpoint Number➀ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Present Unit Password ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


















Data FormatÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




0 to 1

➀ See Table B.5 in Publication 1403-5.1 for specific command bits toenable these features.



Table B.5 Bit Fields for Command Data Table – (Command Word 1)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

CommandÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Bit Locationand Value


Clear Snapshot Log ÁÁÁÁÁÁÁÁÁÁÁÁ

b0 = 1


Clear Min_Max Log ÁÁÁÁÁÁÁÁÁÁÁÁ

b1 = 1

ÁÁÁÁÁÁÁÁÁÁÁRestore Factory Default Configuration ÁÁÁÁÁÁb2 = 1ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Clear Hold of Oscillogram (Reserved1403-LM)


b3 = 1


Initiate Oscillogram (Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁ

b4 = 1ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Force Self Test ÁÁÁÁÁÁÁÁÁÁÁÁ

b5 = 1


Clear Status Input Counter 1 ÁÁÁÁÁÁÁÁÁÁÁÁ

b6 = 1



b7 = 1



b8 = 1ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁClear Status Input Counter 4

ÁÁÁÁÁÁÁÁÁÁÁÁb9 = 1ÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁClear Battery Usage TimerÁÁÁÁÁÁÁÁÁÁÁÁb10 = 1

Table B.6 Bit fields for Command Data Table – (Command Word 2)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

CommandÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Bit Locationand Value


Set Analysis Channel Request ÁÁÁÁÁÁÁÁÁÁÁÁ

b0 = 1


Set Oscillogram Channel Request(Reserved 1403-LM)



Set W HoursÁÁÁÁÁÁÁÁÁÁÁÁ


Set VAR HoursÁÁÁÁÁÁÁÁÁÁÁÁ


Reserved ÁÁÁÁÁÁÁÁÁÁÁÁ

b4 = not usedÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Set Time ÁÁÁÁÁÁÁÁÁÁÁÁ

b5 = 1


Relay 1 ÁÁÁÁÁÁÁÁÁÁÁÁ

b6 = 1


Relay 2 ÁÁÁÁÁÁÁÁÁÁÁÁ

b7 = 1


Select Setpoint Number ÁÁÁÁÁÁÁÁÁÁÁÁ

b8 = 1

Table B.7 Voltage/Current Data – Read


Parameter No.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter Name ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Word No. ÁÁÁÁÁÁÁÁÁÁ

Range



Time Stamp ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Year ÁÁÁÁÁÁÁÁÁÁ


0–9916 Bit IntegerÁÁÁÁÁ




Month, DateÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

2ÁÁÁÁÁÁÁÁÁ

1–128 Bit

ÁÁÁÁÁÁÁÁÁ

1–318 Bit




Hour, Minute ÁÁÁÁÁÁÁÁÁÁ

3 ÁÁÁÁÁÁ






Seconds, HundredthsÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

4ÁÁÁÁÁÁÁÁÁ

0–598 Bit

ÁÁÁÁÁÁÁÁÁ

0–998 Bit



L1 Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 amps ÁÁÁÁÁÁÁÁÁÁ


0 to 9999






10±0 to 21



L2 Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ









ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL3 Current

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 amps







10±0 to 21



L4 (Neutral) CurrentÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 ampsÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



3-Phase Average Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Positive Sequence Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁNegative Sequence Current

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 amps









Percent Current UnbalanceÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0.0 to 100.0ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



L1 to L2 Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 volts ÁÁÁÁÁÁÁÁÁÁ


0 to9999ÁÁÁÁÁÁÁÁÁÁ





10±0 to 21






0 to 9999






10±0 to 21










ÁÁÁÁÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁ

ÁÁÁÁÁ4.13ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁAUX Voltage

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 volts


ÁÁÁÁÁÁÁÁÁÁ0 to 9999





Word No.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Master Module RangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter NameÁÁÁÁÁÁÁÁÁÁ

Parameter No.ÁÁÁÁÁÁÁÁÁÁ





ÁÁÁÁÁ4.14ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ3–Phase Average Voltage (L–L)








10±0 to 21



Positive Sequence VoltageÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 voltsÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Negative Sequence Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Percent Voltage Unbalance ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0.0 to 100.0 ÁÁÁÁÁÁÁÁÁÁ


0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL1–N Voltage










L2–N VoltageÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



L3–N Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



3–Phase Average Voltage (L–N) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21


4 22 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Average Frequency ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

20 0 to 132 0 ÁÁÁÁÁÁÁÁÁÁ




Average Frequency ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

20.0 to 132.0 ÁÁÁÁÁÁÁÁÁÁ46


ÁÁÁÁÁ4.23ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁLast Cycle Frequency

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ20.0 to 132.0







10±0 to 21


4.24


Phase Rotation


0 = No Rotation1 = ABC2 = ACB


49


0 to 2



Reserved WordÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








Reserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ









0 to 1

Table B.8 Real Time Power Data – ReadÁÁÁÁÁÁÁÁÁÁ

Parameter No.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



Word No. ÁÁÁÁÁÁÁÁÁÁÁÁ

RangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Time StampÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

YearÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


0–9916 Bit IntegerÁÁÁÁÁ




Month, Date


2

ÁÁÁÁÁÁÁÁÁ

1–128 Bit


1–318 Bit




Hour, MinuteÁÁÁÁÁÁÁÁÁÁ

3ÁÁÁÁÁÁ

0–238 BitÁÁÁÁÁÁÁÁ





Seconds, Hundredths


4

ÁÁÁÁÁÁÁÁÁ

0–598 Bit


0–998 Bit



L1 Real Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 W ÁÁÁÁÁÁÁÁÁÁ


0 to 9999






10±0 to 21

ÁÁÁÁÁ5.3 ÁÁÁÁÁÁÁÁÁÁÁL2 Real Power ÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 W ÁÁÁÁÁ7 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁ




ÁÁÁÁÁÁÁÁÁÁÁÁ10±0 to 21



L3 Real PowerÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 WÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Total Real Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



L1 Reactive Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 VAR ÁÁÁÁÁÁÁÁÁÁ











Word No.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Parameter NameÁÁÁÁÁÁÁÁÁÁ

Parameter No.ÁÁÁÁÁÁÁÁÁÁ5.7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL2 Reactive Power

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 VAR







10±0 to 21



L3 Reactive Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Total Reactive Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁ5.10 ÁÁÁÁÁÁÁÁÁÁÁL1 Apparent Power ÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 VA ÁÁÁÁÁ21 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁ







L2 Apparent PowerÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 VAÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



L3 Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 VA ÁÁÁÁÁÁÁÁÁÁ


0 to 9999






10±0 to 21



Total Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ










L1 True PFÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–100.0 to +100.0ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



L2 True PF ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–100.0 to +100.0 ÁÁÁÁÁÁÁÁÁÁ


–9999 to +9999






10±0 to 21



L3 True PF ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



–9999 to +9999

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ34 ÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁÁÁÁÁÁ5.17

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁTotal True PF

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–100.0 to +100.0


ÁÁÁÁÁÁÁÁÁÁÁÁ–9999 to +9999ÁÁÁÁÁ





10±0 to 21



L1 Displacement PF➀ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



L2 Displacement PF➀ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



–9999 to +9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL3 Displacement PF➀

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–100.0 to +100.0


ÁÁÁÁÁÁÁÁÁÁÁÁ–9999 to +9999ÁÁÁÁÁ





10±0 to 21



Total Displacement PF➀ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



L1 Distortion PF➀ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to +100.0 ÁÁÁÁÁÁÁÁÁÁ


0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL2 Distortion PF➀

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to +100.0







0±0 to 21



L3 Distortion PF➀ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








0±0 to 21



Total Distortion PF➀ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ53 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word







55ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Reserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ























61ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



Data FormatÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




0 to 1

➀ This value has the same update rate as harmonic analysis.



Table B.9 Cumulative Power Data – Read

ÁÁÁÁÁÁParameter No. ÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No.ÁÁÁÁÁÁRange ÁÁÁÁÁÁModulusÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁYear


ÁÁÁÁÁÁÁÁÁÁÁÁ0–99 16 Bit Integer



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁS




1–128 Bit

ÁÁÁÁÁÁÁÁÁ

1–318 Bit


N/A


6.1 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Time Stamp ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


3 ÁÁÁÁÁÁÁÁ


0–598 BitÁÁÁÁÁÁÁÁÁÁÁÁ

N/AÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





0–598 Bit

ÁÁÁÁÁÁÁÁÁ

0–998 Bit


N/A



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



+0 to 999 ÁÁÁÁÁÁÁÁÁÁÁÁ

1012







109

ÁÁÁÁÁÁ6.2 ÁÁÁÁÁÁÁÁkW Hours Forward ÁÁÁÁÁÁÁ0 to 1.0x1012 ÁÁÁÁÁ7 ÁÁÁÁÁÁ+0 to 999 ÁÁÁÁÁÁ106ÁÁÁÁÁÁÁÁÁÁÁÁ


kW Hours Forward ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 1.0x10 ÁÁÁÁÁÁÁÁÁÁ8

ÁÁÁÁÁÁÁÁÁÁÁÁ+0 to 999

ÁÁÁÁÁÁÁÁÁÁÁÁ103






+0 to 999ÁÁÁÁÁÁÁÁÁÁÁÁ

100






–0 to 999 ÁÁÁÁÁÁÁÁÁÁÁÁ

1012







109



kW Hours Reverse ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–1.0x1012 to 0 ÁÁÁÁÁÁÁÁÁÁ



106


6.3


kW Hours Reverse


1.0x10 to 0




103







100

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ15 ÁÁÁÁÁÁ±0 to 999 ÁÁÁÁÁÁ1012ÁÁÁÁÁÁÁÁÁÁÁÁ




ÁÁÁÁÁÁÁÁÁÁÁÁ±0 to 999



6.4ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

kW Hours NetÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–1.0x1012 to 1.0x1012ÁÁÁÁÁÁÁÁÁÁ


±0 to 999ÁÁÁÁÁÁÁÁÁÁÁÁ

106



kW Hours NetÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.0x10 to 1.0x10ÁÁÁÁÁÁÁÁÁÁ


±0 to 999 ÁÁÁÁÁÁÁÁÁÁÁÁ

103







100







1012







109



kVAR Hours Forward ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 1.0x1012 ÁÁÁÁÁÁÁÁÁÁ



106

ÁÁÁÁÁÁ6.5

ÁÁÁÁÁÁÁÁkVAR Hours Forward

ÁÁÁÁÁÁÁ0 to 1.0x10

ÁÁÁÁÁ23 ÁÁÁÁÁÁ+0 to 999 ÁÁÁÁÁÁ103ÁÁÁÁÁÁÁÁÁÁÁÁ




ÁÁÁÁÁÁÁÁÁÁÁÁ+0 to 999







–0 to 999ÁÁÁÁÁÁÁÁÁÁÁÁ

1012







109



kVAR Hours Reverse ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–1.0x1012 to 0 ÁÁÁÁÁÁÁÁÁÁ



106



kVAR Hours ReverseÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.0x10 to 0ÁÁÁÁÁÁÁÁÁÁ



103







100







1012

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ31 ÁÁÁÁÁÁ±0 to 999 ÁÁÁÁÁÁ109ÁÁÁÁÁÁÁÁÁÁÁÁ6.7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁkVAR Hours Net

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–1.0x1012 to 1.0x1012


ÁÁÁÁÁÁÁÁÁÁÁÁ±0 to 999




kVAR Hours Net ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1.0x10 to 1.0x10 ÁÁÁÁÁÁÁÁÁÁ



103







100



Reserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ













ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word ÁÁÁÁÁÁÁÁÁÁÁÁ38 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ







Reserved WordÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

























ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word







Table B.10 Demand Data – Read

ÁÁÁÁÁParameter No.ÁÁÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No. ÁÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

7.1


Time Stamp


Year


1


0–9916 Bit Integer




Month, DateÁÁÁÁÁÁÁÁÁÁ

2ÁÁÁÁÁÁ






Hour, Minute


3

ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





4ÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁ7.2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁDemand Current

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 amps



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





7.3ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Demand PowerÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 WÁÁÁÁÁÁÁÁÁÁ







10±0 to 21


7.4 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Demand Reactive Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Demand Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Projected No. 1 Demand Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








ÁÁÁÁÁ7.7ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁProjected No. 1 Demand Power

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 W







10±0 to 21



Projected No. 1 Demand Reactive PowerÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 VARÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Projected No. 1 Demand Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21






0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁProjected No. 2 Demand Power










Projected No. 2 Demand Reactive PowerÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 VARÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Projected No. 2 Demand Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21






0 to 9999






10±0 to 21



Projected No. 3 Demand Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁProjected No. 3 Demand Reactive Power

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 VAR






34ÁÁÁÁÁÁÁÁÁÁÁÁ10±0 to 21



Projected No. 3 Demand Apparent PowerÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Elapsed Time ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x1021 ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21









40 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ41 ÁÁÁÁÁÁÁÁÁÁÁ


7.19


Data Format




42


0 to 1



Table B.11 Event Log – Read

ÁÁÁÁÁÁParameter No. ÁÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No. ÁÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

8.1


Event Time Log Stamp


Year


1







2ÁÁÁÁÁÁ






Hour, Minute


3

ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





4ÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁ8.2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁEvent Type Value



ÁÁÁÁÁÁÁÁÁÁÁÁ0 to 14ÁÁÁÁÁÁ

ÁÁÁÁÁÁ8.3ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁEvent Code Value




ÁÁÁÁÁÁ8.4


Setpoint TypeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 54ÁÁÁÁÁÁÁÁÁÁÁÁ


Setpoint Evaluation ConditionÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Setpoint Level ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

±9999x1021 ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Setpoint Action/Release Delay ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999



Setpoint Action ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 20



Number of Event Logs Requested ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



1 to 100ÁÁÁÁÁÁÁÁÁÁÁÁ8.10

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁNumber of Event Log Received (Counter)




ÁÁÁÁÁÁ8.11ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁNumber of Event Log Being Returned




ÁÁÁÁÁÁ8.12


Internal IdentifierÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



–32767 to +32767ÁÁÁÁÁÁÁÁÁÁÁÁ


Reserved WordÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



18 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


















8.13


Data Format




23


0 to 1



Table B.12 Voltage/Current/Miscellaneous Snapshot Log Data Table Read

ÁÁÁÁÁÁParameter No. ÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁÁMaster Module Parameter Range ÁÁÁÁÁWord No. ÁÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

9.1


Event Time Log Stamp


Year


1







2ÁÁÁÁÁÁ






Hour, Minute


3

ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





4ÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁ9.2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved




ÁÁÁÁÁÁ9.3ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL1 Current

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 amps



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




10±0 to 21


9.4ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

L2 CurrentÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21


9.5 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

L3 Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



L4 (Neutral) Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21ÁÁÁÁÁÁÁÁÁÁÁÁ9.7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ3-Phase Average Current

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 amps









Positive Sequence CurrentÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Negative Sequence Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Percent Current Unbalance ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



L1–L2 Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ







ÁÁÁÁÁÁÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁÁ

ÁÁÁÁÁÁ9.12ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL2–L3 Voltage

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 volts







10±0 to 21



L3–L1 VoltageÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



AUX Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



3-Phase Average Voltage (L–L) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ9.16 ÁÁÁÁÁÁÁÁÁÁPositive Sequence Voltage ÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 volts ÁÁÁÁÁ32 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ







Negative Sequence VoltageÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Percent Voltage Unbalance ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



L1–N Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



L2–N Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ41 ÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁÁÁÁÁÁÁÁ9.21

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL3–N Voltage













Master Module Parameter RangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter NameÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter No.ÁÁÁÁÁÁÁÁÁÁÁÁ9.22

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ3–Phase Average Voltage (L–N)










ReservedÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




ReservedÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁ9.23 ÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁLast Cycle Frequency ÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁ20.0 to 132.0 ÁÁÁÁÁ

ÁÁÁÁÁ48 ÁÁÁÁÁÁÁÁÁÁÁÁ






10±0 to 21


9.24ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Phase RotationÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = No Rotation1 = ABC2 = ACB



0 to 2



Number of Snapshot Logs RequestedÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Number of snapshot Log Received(Counter)




1 to 50ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

9.27


Number of Snapshot Log BeingReturned


1 to 50


53


1 to 50



Internal Identifier ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–32767 to +32767 ÁÁÁÁÁÁÁÁÁÁ


–32767 to +32767

Table B.13 Power Snapshot Log Data TableÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter No.


Parameter Name


Master ModuleParameter Range


Word No.


Range



Event Time Log StampÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ







Month, Date ÁÁÁÁÁÁÁÁÁÁ

2 ÁÁÁÁÁÁ


1–318 Bit




Hour, MinuteÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

3ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit




Seconds, Hundredths ÁÁÁÁÁÁÁÁÁÁ

4 ÁÁÁÁÁÁ


0–598 Bit






ÁÁÁÁÁÁ10.3 ÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁL1 Real Power ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁ0 to 9999x1021 W ÁÁÁÁÁ







10±0 to 21



L2 Real Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



L3 Real Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








ÁÁÁÁÁÁÁÁÁÁÁÁ10.6

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁTotal Real Power








10±0 to 21



L1 Reactive Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21






0 to 9999






10±0 to 21






0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁTotal Reactive Power

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 VAR









L1 Apparent PowerÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



L2 Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



L3 Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999





Word No.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




Parameter No.ÁÁÁÁÁÁÁÁÁÁÁÁ





10±0 to 21



Total Apparent Power ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



L1 True PF ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



–9999 to +9999






10±0 to 21



L2 True PF ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



–9999 to +9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁL3 True PF

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–100.0 to +100.0


ÁÁÁÁÁÁÁÁÁÁÁÁ–9999 to +9999ÁÁÁÁÁÁ







Total True PFÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–100.0 to +100.0ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



L1 Displacement PF ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21






–9999 to +9999






10±0 to 21











ÁÁÁÁÁÁ10.22ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁTotal Displacement PF

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–100.0 to +100.0


ÁÁÁÁÁÁÁÁÁÁÁÁ–9999 to +9999ÁÁÁÁÁÁ





10±0 to 21



L1 Distortion PFÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 100.0ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



L2 Distortion PF ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 100.0 ÁÁÁÁÁÁÁÁÁÁ


0 to 9999






10±0 to 21



L3 Distortion PF ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 100.0 ÁÁÁÁÁÁÁÁÁÁ


0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁTotal Distortion PF

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 100.0









Number of Snapshot Logs RequestedÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Number of snapshot Log Received (Counter)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Number of Snapshot Log Being Returned ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Internal Identifier ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–32767 to +32767 ÁÁÁÁÁÁÁÁÁÁ


–32767 to +32767






ÁÁÁÁÁÁ10.31 ÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁData Format ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁ0 = Integer/Exponent1 = Floating Point



0 to 1



Table B.14 Min_Max Log – Read


Parameter No. ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Range



Time Stamp of last Min/Max Log ResetÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








2 ÁÁÁÁÁÁ


1–318 Bit





3ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





4 ÁÁÁÁÁÁ





Time Stamp of MIN for ParameterÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








6 ÁÁÁÁÁÁ







7ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





8 ÁÁÁÁÁÁ



ÁÁÁÁÁÁ11.3


MIN Value for ParameterÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999x10ÁÁÁÁÁÁÁÁÁÁ

9ÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999

±0 t 21ÁÁÁÁÁÁÁÁÁÁÁÁ





0 to 999910±0 to 21



Time Stamp of MAX for ParameterÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








12 ÁÁÁÁÁÁ


1–318 Bit





13ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





14 ÁÁÁÁÁÁ


0–998 Bit



MAX Value for Parameter ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Number of Min_Max Logs Requested ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



1 to 84



Number of Min_Max Log Received (Counter)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



1 to 84



Number of Min_Max Log Being Returned ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



1 to 84











ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word










Data FormatÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




0 to 1



Table B.15 Log Selection Command Table Write

ÁÁÁÁÁÁParam. No. ÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No. ÁÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

12.1


Selected Log


23 = Event Log24 = Min/Max Log54 = Snapshot V/I Log59 = Snapshot Power Log


1


23, 24, 54, 59


12.2


Requested Number of Data Sets


1 to 100 for Event Log1 to 84 for Min/Max Log1 to 50 for Snapshot V/I Log1 to 50 for Snapshot Power Log


2


1 to 1001 to 841 to 501 to 50



Chronology of Returned DataÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = Reverse1 = ForwardNote: Not used for Min/Max Log



0 to 1



First Min/Max Parameter to beReturned


1 to 84ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word




ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word


















Table B.16 Available Min/Max Log Parameters (Identifiers for parameter 12.4)Parameter Number Parameter Description

1 Phase 1 Current

2 Phase 2 Current

3 Phase 3 Current

4 Phase 4 Current

5 Average Current

6 Positive Sequence Current

7 Negative Sequence Current

8 Current Unbalance

9 Phase 1 L–L Voltage



12 Auxiliary Voltage

13 Average L–L Voltage

14 Positive Sequence Voltage

15 Negative Sequence Voltage

16 Voltage Unbalance

17 Phase 1 L–N Voltage



20 Average L–N Voltage

21 Frequency

22 Phase 1 Real Power



25 Total Real Power

26 Phase 1 Reactive Power



29 Total Reactive Power

30 Phase 1 Apparent Power



33 Total Apparent Power

34 Phase 1 True Power Factor



37 Total True Power Factor

38 Phase 1 Displacement Power Factor



41 Total Displacement Power Factor

42 Phase 1 Distortion Power Factor

Parameter Number Parameter Description



45 Total Distortion Power Factor

46 Current Demand

47 Real Power Demand

48 Reactive Power Demand

49 Apparent Power Demand

50 Phase 1 Voltage IEEE THD

51 Phase 1 Voltage IEC THD

52 Phase 1 Voltage TIF①

53 Phase 1 Voltage Crest Factor①

54 Phase 1 Voltage K-factor①

55 Phase 1 Current IEEE THD

56 Phase 1 Current IEC THD

57 Phase 1 Current TIF①

58 Phase 1 Current Crest Factor①

59 Phase 1 Current K-factor①


























➀ Not available on 1403-LM.



Harmonic Distortion T ables – Read

Harmonic Distortion Data Tables for Channel 2 through Channel 7 are identical to the Even and Odd HarmonicDistortion Tables for Channel 1. There are a total of 14 tables for this information.

(V1, V2, V3, I1, I2, I3, I4) The table sizes indicate this is Harmonic Distortion Data. The Channel Number designateswhich one.

Table B.17 Even Harmonic Distortion Table – Channel 1


Parameter No. ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




Range

ÁÁÁÁÁÁ13.1 ÁÁÁÁÁÁÁÁÁÁIEEE Total Harmonic Distortion ÁÁÁÁÁÁÁÁÁÁ0 to 1000% ÁÁÁÁÁ1 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ






ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁIEC Total Harmonic Distortion

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 1000%







10±0 to 21


13.3


Meets IEEE 519(Reserved 1403-LM)


–1 = Unknown 0 = Fail 1 = Pass


5


–1 to +1



TIFÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





(Reserved 1403-LM)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



10±0 to 21



Crest Factor ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





(Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



10±0 to 21



K-Factor ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21


13.7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Channel Number




12


1 to 7



Harmonic Distortion – FundamentalÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 1000%ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Harmonic Distortion – Second ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 1000% ÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Harmonic Distortion – Fourth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ13.11 ÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Sixth ÁÁÁÁÁÁÁÁÁÁ0 to 1000% ÁÁÁÁÁ19 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ(Reserved 1403-LM)





ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Eighth

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 1000 %







10±0 to 21



Harmonic Distortion – Tenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Twelfth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Distortion – Fourteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ(Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ28 ÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁÁÁÁÁÁÁÁ13.16

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Sixteenth




ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ(Reserved 1403-LM)






Harmonic Distortion – EighteenthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Twentieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21






Master Module RangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Twenty-second










Harmonic Distortion – Twenty-fourthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Twenty-sixth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Twenty-eighth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Distortion – Thirtieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








ÁÁÁÁÁÁ13.24ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Thirty-second








10±0 to 21



Harmonic Distortion – Thirty-fourthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Thirty-sixth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Distortion – Thirty-eighth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ13.28 ÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Fortieth ÁÁÁÁÁÁÁÁÁÁ0 to 1000% ÁÁÁÁÁ53 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ







FFT Chronological Reference NumberÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





















ÁÁÁÁÁÁÁÁÁÁData Format ÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁ0 = Integer/Exponent1 = Floating Point



0 to 1

Table B.18 Odd Harmonic Distortion Table – Channel 1ÁÁÁÁÁÁÁÁÁÁÁÁParameter No.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁParameter Name

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁMaster Module Range

ÁÁÁÁÁÁÁÁÁÁWord No.

ÁÁÁÁÁÁÁÁÁÁÁÁRangeÁÁÁÁÁÁ

ÁÁÁÁÁÁ14.1


IEEE Total Harmonic DistortionÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



IEC Total Harmonic Distortion ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21








–1 to +1



TIF Value ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCrest Factor

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021







10±0 to 21



K-Factor ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21


14.7


Channel Number




12


1 to 7



Harmonic Distortion – FundamentalÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999















Harmonic Distortion – ThirdÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Fifth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Seventh ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Ninth








10±0 to 21



Harmonic Distortion – Eleventh ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Thirteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Fifteenth








10±0 to 21



Harmonic Distortion – Seventeenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Nineteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ14.18 ÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Twenty-first ÁÁÁÁÁÁÁÁÁÁ0 to 1000% ÁÁÁÁÁ33 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ







Harmonic Distortion – Twenty-thirdÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Twenty-fifth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ14.21 ÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Twenty-seventhÁÁÁÁÁÁÁÁÁÁ0 to 1000% ÁÁÁÁÁ39 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ







Harmonic Distortion – Twenty-ninthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Thirty-first ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Distortion – Thirty-third ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ










Harmonic Distortion – Thirty-fifthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Thirty-seventh ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Distortion – Thirty-ninth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Distortion – Forty-first








10±0 to 21


































0 to 1



Harmonic Magnitude Data Tables for Channel 2 through Channel 7 are identical to the Even and Odd HarmonicMagnitude Tables for Channel 1. There are a total of 14 tables for this information. (V1, V2, V3, I1, I2, I3, I4)

Table B.19 Even Harmonic Magnitude Data Table Channel 1ÁÁÁÁÁÁÁÁÁÁÁÁParameter No.





ÁÁÁÁÁÁ15.1










10±0 to 21











10±0 to 21








–1 to +1






0 to 9999






10±0 to 21






0 to 9999






10±0 to 21

ÁÁÁÁÁÁ15.6 ÁÁÁÁÁÁÁÁÁÁK-Factor ÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 ÁÁÁÁÁ10 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ






15.7


Channel Number




12


1 to 7



Harmonic Magnitude – Fundamental ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Second ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Fourth










Harmonic Magnitude – SixthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Eighth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Tenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Twelfth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ









ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Fourteenth








10±0 to 21



Harmonic Magnitude – Sixteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Eighteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Twentieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Twenty-second
















ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Twenty-fourth










Harmonic Magnitude – Twenty-sixthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Twenty-eighth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Thirtieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Thirty-second ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








ÁÁÁÁÁÁ15.25ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Thirty-fourth








10±0 to 21



Harmonic Magnitude – Thirty-sixthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Thirty-eighth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Fortieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ15.29 ÁÁÁÁÁÁÁÁÁÁFFT Update Reference Number ÁÁÁÁÁÁÁÁÁÁ0 to 32767 ÁÁÁÁÁ55 ÁÁÁÁÁÁ0 to 32767ÁÁÁÁÁÁÁÁÁÁÁÁ















0 t o 1

Table B.20 Odd Harmonic Magnitude Data TableÁÁÁÁÁÁÁÁÁÁÁÁParameter No.





ÁÁÁÁÁÁ16.1










10±0 to 21











10±0 to 21








–1 to +1






0 to 9999






10±0 to 21






0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁK-Factor









16.7


Channel Number




12


1 to 7



Harmonic Magnitude – Fundamental ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Third ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ(Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ16 ÁÁÁÁÁÁ10±0 to 21









ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Fifth










Harmonic Magnitude – SeventhÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Ninth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Eleventh ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Thirteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








ÁÁÁÁÁÁ16.15ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Fifteenth








10±0 to 21



Harmonic Magnitude – SeventeenthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Nineteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Twenty-first ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ16.19 ÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Twenty-third ÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 ÁÁÁÁÁ35 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ







Harmonic Magnitude – Twenty-fifthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Twenty-seventhÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Twenty-ninth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Magnitude – Thirty-first ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Thirty-third










Harmonic Magnitude – Thirty-fifthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Thirty-seventhÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Magnitude – Thirty-ninth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ16.28 ÁÁÁÁÁÁÁÁÁÁHarmonic Magnitude – Forty-first ÁÁÁÁÁÁÁÁÁÁ0 to 9999x1021 ÁÁÁÁÁ53 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ






ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁFFT Chronological Reference Number

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 32767













0 to 1



Harmonic Phase Angle Data Tables for Channel 2 through Channel 7 are identical to the Even and Odd Harmonic PhaseAngle Data Tables for Channel 1. There are a total of 14 tables for this information. (V1, V2, V3, I1, I2, I3, I4)

Table B.21 Even Harmonic Phase Angle Data Table Channel 1


Parameter No. ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




Range

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ1 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ














10±0 to 21






0 –1ÁÁÁÁÁÁÁÁÁÁÁÁ










10±0 to 21






0 to 9999






10±0 to 21












17.7


Channel Number(Reserved 1403-LM)




12


1 to 7



Harmonic Phase Angle – FundamentalÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 360 degrees ÁÁÁÁÁÁÁÁÁÁ


0 to 9999






10±0 to 21



Harmonic Phase Angle – Second ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Fourth

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 360 degrees









Harmonic Phase Angle – SixthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 360 degreesÁÁÁÁÁÁÁÁÁÁ







10±0 to 21



Harmonic Phase Angle – Eighth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Tenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Phase Angle – Twelfth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Fourteenth








10±0 to 21



Harmonic Phase Angle – SixteenthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Eighteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Twentieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ17.19 ÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Twenty-secondÁÁÁÁÁÁÁÁÁÁ0 to 360 degrees ÁÁÁÁÁ35 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ






ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Twenty-fourth








10±0 to 21









ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Twenty-sixth










Harmonic Phase Angle – Twenty-eighthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Thirtieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Thirty-secondÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Phase Angle – Thirty-fourthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








ÁÁÁÁÁÁ17.26ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Thirty-sixth








10±0 to 21



Harmonic Phase Angle – Thirty-eighthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Fortieth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21






0 to 32767



Data Format ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




0 to 1

Table B.22 Odd Harmonic Phase Angle Data Table


Parameter No. ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




Range






0 to 9999

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ2 ÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁÁÁÁÁÁÁÁ





ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word









0 –1ÁÁÁÁÁÁÁÁÁÁÁÁ










10±0 to 21






0 to 9999






10±0 to 21






0 to 9999






10±0 to 21ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

18.7ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



12ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 to 7



Harmonic Phase Angle – Fundamental ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





(Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



10±0 to 21



Harmonic Phase Angle – Third ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Phase Angle – Fifth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ(Reserved 1403-LM)




ÁÁÁÁÁÁ18.11ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Seventh

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 360 degrees




(Reserved 1403-LM)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



10±0 to 21



Harmonic Phase Angle – NinthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999













ÁÁÁÁÁÁ18.13ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Eleventh








10±0 to 21



Harmonic Phase Angle – ThirteenthÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Fifteenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Phase Angle – Seventeenth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Nineteenth




ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ(Reserved 1403-LM)






Harmonic Phase Angle – Twenty-firstÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Twenty-third ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Twenty-fifth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21



Harmonic Phase Angle – Twenty-seventh ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ(Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ40 ÁÁÁÁÁÁ10±0 to 21ÁÁÁÁÁÁÁÁÁÁÁÁ18.22

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Twenty-ninth








10±0 to 21



Harmonic Phase Angle – Thirty-firstÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Thirty-third ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



Harmonic Phase Angle – Thirty-fifth ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999






10±0 to 21

ÁÁÁÁÁÁ18.26 ÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Thirty-seventh ÁÁÁÁÁÁÁÁÁ0 to 360 degrees ÁÁÁÁÁ49 ÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ






ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁHarmonic Phase Angle – Thirty-ninth








10±0 to 21



Harmonic Phase Angle – Forty-first ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








10±0 to 21



FFT Chronological Reference Number ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 32767



Table B.23 Oscillogram Capture Data – Read (54 Reads of 48 data points for 2-channel 12-cycle oscillogram or 9 Reads of 48 data pointsfor 7-channel 2-cycle oscillogram)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter No.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameter NameÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Master ModuleRange



Range


19.1 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Time Stamp of Oscillogram ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Year ÁÁÁÁÁÁÁÁÁÁ


0–9916 Bit IntegerÁÁÁÁÁÁ


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

(Reserved 1403-LM)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


2ÁÁÁÁÁÁÁÁÁ

1–128 Bit


1–318 Bit





3 ÁÁÁÁÁÁ




ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



4ÁÁÁÁÁÁÁÁÁ

0–598 Bit


0–998 Bit


19.2

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

1 = L1 Voltage2 = L1 Current3 = L2 Voltage4 = L2 Current5 = L3 Voltage6 = L3 Current7 = L4 Current8 = Ch A 12-Cycle9 = Ch B 12-Cycle


5


1 to 9



Channel Data Count (Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

for 2-cycle 432for 12-cycle 2592



432 or 2592


19.4ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Oscillogram Chronological Reference Number(Reserved 1403-LM)


0 to +32767ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


0 to 32767



Oscillogram Block Number (Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



1 to 54ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

19.6

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Actual Channel Numer(Reserved 1403-LM)




9


1 to 7



Oscillogram Data Point 1 (Reserved 1403-LM) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

±5000 ÁÁÁÁÁÁÁÁÁÁ


±5000ÁÁÁÁÁÁÁÁÁÁÁÁ










±5000






±5000






±5000

ÁÁÁÁÁÁ19.12 ÁÁÁÁÁÁÁÁÁÁÁÁÁOscillogram Data Point 6 (Reserved 1403-LM) ÁÁÁÁÁÁÁ±5000 ÁÁÁÁÁ15 ÁÁÁÁÁÁ±5000ÁÁÁÁÁÁÁÁÁÁÁÁ19.13

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁOscillogram Data Point 7 (Reserved 1403-LM)

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ±5000


ÁÁÁÁÁÁÁÁÁÁÁÁ±5000ÁÁÁÁÁÁ

ÁÁÁÁÁÁ19.14ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁOscillogram Data Point 8 (Reserved 1403-LM)




ÁÁÁÁÁÁ19.15


Oscillogram Data Point 9 (Reserved 1403-LM)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

±5000ÁÁÁÁÁÁÁÁÁÁ

















±5000






±5000






±5000

ÁÁÁÁÁÁ19.21 ÁÁÁÁÁÁÁÁÁÁÁÁÁOscillogram Data Point 15 (Reserved 1403-LM) ÁÁÁÁÁÁÁ±5000 ÁÁÁÁÁ24 ÁÁÁÁÁÁ±5000ÁÁÁÁÁÁÁÁÁÁÁÁ19.22









ÁÁÁÁÁÁ19.24




















±5000





Word No.ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Master ModuleRange




19.28ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



















±5000






±5000






±5000






±5000ÁÁÁÁÁÁÁÁÁÁÁÁ19.35









ÁÁÁÁÁÁ19.37




















±5000






±5000






±5000















ÁÁÁÁÁÁ19.46






19.47ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ














±5000






±5000






±5000















ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
























For PT Secondary Values 138 Max Voltage = 138.0For PT Secondary Values 138 Max Voltage = 399.0

For MM01A or MM01B Max Current = 1.42For MM05A or MM05B Max Current = 7.10

Max Counts = 4095

Max Voltage or Max Current 2

Max Counts

PT or CT Primary

PT or CT SecondaryOscillogram Data Point Voltage or Current



Table B.24 Diagnostic Data Table (Self-test Results) Read

ÁÁÁÁÁÁParameter No. ÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No. ÁÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

20.1


Time Stamp of Diagnostic Data


Year


1







2 ÁÁÁÁÁÁ







3ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





4 ÁÁÁÁÁÁ



ÁÁÁÁÁÁ20.2


Bulletin NumberÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Master Module FRN ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Options Bit Field ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer



Summary Status ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer



Master Module ROM Status ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit IntegerÁÁÁÁÁÁÁÁÁÁÁÁ20.7

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁMaster Module RAM Status



ÁÁÁÁÁÁÁÁÁÁÁÁ16 Bit IntegerÁÁÁÁÁÁ

ÁÁÁÁÁÁ20.8


NV RAM StatusÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit IntegerÁÁÁÁÁÁÁÁÁÁÁÁ


Power Supply CheckÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Data Acquisition ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Master Module Watchdog Timer ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer



Real Time Clock Status ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer

ÁÁÁÁÁÁ20.13 ÁÁÁÁÁÁÁÁÁÁReserved ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ16 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ20.14

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved




ÁÁÁÁÁÁ20.15


Battery UsageÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Smart Communication Card Status ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Reserved ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




ÁÁÁÁÁÁÁÁÁÁSmart Communication Card Type ÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁ0 = none1 = 1403-NSC





Smart Communication Card FRNÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Number of Display Modules ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Display Module Status ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer



Display Module Self Test Results Word 1ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer



Display Module Self Test Results Word 2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁDisplay Module No. 1 FRN

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ0 to 32767



ÁÁÁÁÁÁ20.25


Display Module No. 2 FRNÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Display Module No. 3 FRN ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Auxiliary Frequency ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ








0 to 32



Fiber Loop Back Test Results ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 = Fail1 = Pass





EEPROM Status ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Device ID ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 255ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

20.31


General Purpose Status Bits


bit 0 = oscillogram capturedbit 1 = snapshot buffer fullbit 2 = oscillogram triggered by asetpoint


35


0 to 7



Block Write Error Status Word (BlockSize ID) ÁÁÁÁÁÁÁÁÁÁ


0 = OKOther value = Error ÁÁÁÁÁ


0 to 64



Block Write Error Status Word(Parameter Number)


0 = OKOther value = Error



0 to 32767ÁÁÁÁÁÁÁÁÁÁÁÁ20.34





ÁÁÁÁÁÁ20.35







Table B.25 Setpoint Setup Data Table – Write/Read

ÁÁÁÁÁÁParameter No. ÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No. ÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁÁÁ21.1

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint Number



ÁÁÁÁÁÁÁÁÁÁ1 to 20ÁÁÁÁÁÁ



Setpoint TypeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 54 (see Table B.26 in Publication1403-5.1)



0 to 54


21.3


Setpoint Evaluation Condition

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Over Forward = 0Over Reverse = 1Under Forward = 2Under Reverse = 3Equal = 4Not Equal = 5


3


0 to 5



Setpoint High Limit ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0.0 to 1,000,000.0 ÁÁÁÁÁÁÁÁÁÁ


0 to 9999






10±0 to 21

ÁÁÁÁÁÁ21.5 ÁÁÁÁÁÁÁÁÁÁSetpoint Low Limit ÁÁÁÁÁÁÁÁÁÁÁ0.0 to 1,000,000.0 ÁÁÁÁÁ6 ÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁ






ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint Action Delay



ÁÁÁÁÁÁÁÁÁÁ0 to 9999ÁÁÁÁÁÁ

ÁÁÁÁÁÁ21.7


Setpoint Release DelayÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



0 to 9999ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Setpoint Action TypeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 20 (see Table B.26 in Publication1403-5.1)



0 to 20



Present Unit Password ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

0 to 9999Default = 0



0 to 9999





12ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




13 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ






















ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁReserved Word










0 to 1



Table B.26 Setpoint TypeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint Type Name

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁValueÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁNot Used (Inactive)


0ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Voltage Unbalance ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

3


Current Unbalance ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

4


Vaux Voltage ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

5


Neutral (I4) Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

6ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁkW

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ7ÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁkVARÁÁÁÁÁÁÁÁÁÁÁÁÁÁ8ÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁkVA



Total True Power FactorÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Total Displacement Power Factor ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Total Distortion Power Factor ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

12


kW Demand ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

13


kVAR Demand ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

14


kVA Demand ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

15ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCurrent Demand


ÁÁÁÁÁÁÁÁÁÁType 1 Predictive Demand AÁÁÁÁÁÁÁÁÁÁÁÁÁÁ17ÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁType 1 Predictive Demand W



Type 1 Predictive Demand VARÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Type 1 Predictive Demand VA ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Type 2 Predictive Demand A ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

21


Type 2 Predictive Demand W ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

22


Type 2 Predictive Demand VAR ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

23


Type 2 Predictive Demand VA ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

24

ÁÁÁÁÁÁÁÁÁÁType 3 Predictive Demand A ÁÁÁÁÁÁÁ25ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁType 3 Predictive Demand W


ÁÁÁÁÁÁÁÁÁÁType 3 Predictive Demand VAR



Type 3 Predictive Demand VAÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Frequency ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Phase Rotation ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


K-Factor: Voltage① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

31


K-Factor: Current① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

32

① Not Available For 1403-LM

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint Type Name

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁValueÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁK-Factor: Neutral Current①



Crest Factor: Voltage①ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Crest Factor: Current① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Crest Factor: Neutral Current① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

36


TIF: Voltage① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

37


TIF: Current① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

38


TIF: Neutral Current① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

39ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁIEEE THD: Voltage

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ40ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁIEEE THD: CurrentÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ41ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁIEEE THD: Neutral Current



IEC THD: VoltageÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


IEC THD: Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


IEC THD: Neutral Current ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

45


IEEE519: Voltage① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

46


IEEE519: Current① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

47


IEEE519: Neutral Current① ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

48ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁStatus Input No. 1

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ49ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁStatus Input No. 2ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ50ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁStatus Input No. 3



Status Input No. 4ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Any Status Input ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ


Battery Usage Timer ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

54

Table B.27 Setpoint ActionÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint Action

ÁÁÁÁÁÁÁÁÁÁValueÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁNo ActionÁÁÁÁÁÁÁÁÁÁ0ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁActivate Relay No. 1 and Output Flag No. 1


1ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Activate Relay No. 2 and Output Flag No. 2 ÁÁÁÁÁÁÁÁÁÁ


Activate Output Flag No. 3 ÁÁÁÁÁÁÁÁÁÁ



4



5



6



7ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁActivate Output Flag No. 8

ÁÁÁÁÁÁÁÁÁÁ8ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁActivate Output Flag No. 9ÁÁÁÁÁÁÁÁÁÁ9ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁActivate Output Flag No. 10



Activate Output Flag No. 11ÁÁÁÁÁÁÁÁÁÁ





13



14



15



16ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁInitiate Waveform Capture①

ÁÁÁÁÁÁÁÁÁÁ17ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁPerform SnapshotÁÁÁÁÁÁÁÁÁÁ18ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁClear kW-HR Power Counter



Clear kVAR-HR Power CounterÁÁÁÁÁÁÁÁÁÁ

20



Table B.28 Relay/Setpoint Status Table Read

ÁÁÁÁÁÁParameter No. ÁÁÁÁÁÁÁÁÁÁParameter Name ÁÁÁÁÁÁÁÁÁÁMaster Module Range ÁÁÁÁÁWord No. ÁÁÁÁÁÁRangeÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

22.1


Time Stamp


Year


1







2ÁÁÁÁÁÁ






Hour, Minute


3

ÁÁÁÁÁÁÁÁÁ

0–238 Bit


0–598 Bit





4ÁÁÁÁÁÁÁÁÁ




22.2


Relay No. 1 Status (Bit Fields)


0 = De-energized1 = Energized2 = Forced De-energized3 = Forced Energized


5


0 to 3


22.3


Relay No. 2 Status (Bit Fields)


0 = De-energized1 = Energized2 = Forced De-energized3 = Forced Energized


6


0 to 3



Alarm Word ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer



Status Inputs (Bit Fields) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ



16 Bit Integer



Counter Status Input No. 1 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

–32767 to 32767 ÁÁÁÁÁÁÁÁÁÁ


–32767 to 32767

ÁÁÁÁÁÁ22.7 ÁÁÁÁÁÁÁÁÁÁCounter Status Input No. 2 ÁÁÁÁÁÁÁÁÁÁ–32767 to 32767 ÁÁÁÁÁ10 ÁÁÁÁÁÁ–32767 to 32767ÁÁÁÁÁÁÁÁÁÁÁÁ22.8

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCounter Status Input No. 3

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–32767 to 32767


ÁÁÁÁÁÁÁÁÁÁÁÁ–32767 to 32767ÁÁÁÁÁÁ

ÁÁÁÁÁÁ22.9ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁCounter Status Input No. 4

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ–32767 to 32767


ÁÁÁÁÁÁÁÁÁÁÁÁ–32767 to 32767ÁÁÁÁÁÁ

ÁÁÁÁÁÁ22.10


Setpoint No. 1 Status (Bit Fields)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ





Setpoint No. 2 Status (Bit Fields) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ













16 Bit Integer


22,14 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ




16 Bit Integer






16 Bit Integer







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint No. 8 Status (Bit Fields)




ÁÁÁÁÁÁ22.18ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint No. 9 Status (Bit Fields)




ÁÁÁÁÁÁ22.19




















16 Bit Integer






16 Bit Integer






16 Bit Integer







ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint No. 17 Status (Bit Fields)




ÁÁÁÁÁÁ22.27ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁSetpoint No. 18 Status (Bit Fields)




ÁÁÁÁÁÁ22.28






































Table B.29 Status Inputs Bitfield Definitions

Bit Location and Value Description

b0 = 1 Status Input 1 Active




b4 to b15 Reserved

Table B.30 Alarm word Bitfield Definitions


b0 = 1 Alarm Input 1 Active
















Table B.31 Setpoint Status Bitfield Definitions


b0 to b7 Setpoint Assert Counter

b8 = not used Reserved

b9 = 1 Waiting for Release

b10 = 1 Limit Met for Release

b11 = 1 Setpoint Asserted

b12 = 1 Waiting for Assert

b13 = 1 Limit Met for Assert

b14 = 1 Setpoint Released

b15 = 1 Setpoint Active

Appendix C


Serial Communication Protocol Tutorial

The Smart Communication Card supports the DF1 linklayer protocol

For additional information regarding the DF1 link layerprotocol, refer to the Data Highway/Data HighwayPlus /DH-485 Communication Protocol and CommandSet, Allen-Bradley Publication 1770-6.5.16 (November1991).

Table C.1 contains definitions of single byte codes.

Table C.1 Special Byte Codes

Symbol Value

SOH 0x01

STX 0x02

ETX 0x03

EOT 0x04

ENQ 0x05

ACK 0x06

DLE 0x10

NAK 0x15

DST Address of destination Powermonitor II

SRCAddress of master (device that is sending thisrequest)

BCC8 bit block check character. (For Powermonitor IIused only in poll command where it is equal to the2’s compliment of the STN value)

CRC16 bit CRC calculated as described in the CRC16section below.

STNData symbol. Station number of the slave node onyour half-duplex link.

Table C.2 contains definitions of multiple byte codes.

Table C.2 Special Symbol Meanings

Symbol Type Meaning

DLE SOHControlsymbol

Sender symbol that indicates thestart of a master message.

DLE STXControlsymbol

Sender symbol that separates themulti-drop header from the data.

DLE ETXBCC/CRC

Controlsymbol

Sender symbol that terminates amessage.

DLE ACKControlsymbol

Response symbol which signalsthat a message has beensuccessfully received.

DLE NAKControlsymbol

Global link reset command onlyissued by the master. Causes theslaves to cancel all messages thatare ready to transmit to themaster. Typically, the slavereturns the message and an errorcode to the originator.

DLE ENQSender symbol, issued only by themaster, that starts a pollcommand.

DLE EOTControlsymbol

Response symbol used by slavesas a response to a poll when theyhave no messages to send. (Onlysent by Powermonitor II if a pollcommand is sent that was notpreceded by a read requestcommand.)

APP DATA Data symbol

Single characters having hexvalues 00-0F and 11-FF (i.e.,00-FF not including 0x10).Includes data from applicationlayer including user programs andcommon application routines.

DLE DLE Data symbolRepresents the data value or STNvalue of 0x10.

C–2 Serial Communication Protocol Tutorial


Generic Packet Construction

Polling Packet

[ DLE / ENQ / STN / BCC ]

Slave Message Link Packet

[ DLE / STX / APP_DATA / DLE / ETX / CRC ]

APP_DATA = [ DST / SRC / CMD / STS / TNS / TNS /Response_Data ]

Read

Response_Data = [ 1st_dataword_lo / 1st_dataword_hi /... / last_dataword_lo / last_dataword_hi ]

Write

Response_Data = [ Ext Status (if error) ]

Master Message Link Packet

[ DLE / SOH / STN / DLE / STX / APP_DATA / DLE /ETX / CRC]

APP_DATA = [ DST / SRC / CMD / STS / TNS / TNS /Command_Block ]

Read

Command_Block = [ FNC_byte / Byte_size /File_number / File_type / Element_number /Sub-element_number ]

FNC_byte = 0xA2

byte_size = size/ID of data table being requested in bytes (words X 2)

file_number = 0x00

file_type = 0x89

element_number = 0x00

sub-element_number = 0x00

Write

Command_Block = [ FNC_byte / Byte_size /File_number / File_type / Element_number /Sub-element_number / 1st_dataword_lo /1st_dataword_hi / ... / last_dataword_lo /last_dataword_hi ]

FNC_byte = 0xAA

byte_size = size/ID of data table being requested in bytes (words X 2)

file_number = 0x00

file_type = 0x89

element_number = 0x00

sub-element_number = 0x00

C–3Serial Communication Protocol Tutorial


Table C.3 Write Sequence

Transmitted from SerialNetwork Master

Description/Direction

Transmitted fromSmart

CommunicationCard

[ DLE / SOH / STN / DLE /STX / DST / SRC / 0x0F /0x00 / 0x00 / 0x00 / 0xAA/ data_size / 0x00 / 0x89 /0x00 / 0x00 /1st_dataword_lo /1st_dataword_hi /.../last_dataword_lo /last_dataword_hi / DLE /ETX / CRC ]

Write Data

DF1 Ack

[ DLE / ACK ]


(Note: should wait forapplication ack, time-out,and repeat poll until datais received)

Poll

ApplicationAck [ DLE / STX / DST /

SRC / 0x4F / STS /TNS / TNS /Ext_STS(if error) / DLE / ETX/ CRC ]

[ DLE / ACK ]

DF1 Ack

Table C.4 Read Sequence

Transmitted from SerialNetwork Master



CommunicationCard

[ DLE / SOH / STN / DLE /STX / DST / SRC / 0x0F /0x00 / 0x00 / 0x00 / 0xA2 /data_size / 0x00 / 0x89 /0x00 / 0x00 / DLE / ETX /CRC ]

ReadRequest

DF1 Ack

[ DLE / ACK ]


(Note: should wait fordata, time-out, and repeatpoll until data is received)

Poll

Data[ DLE / STX / DST /SRC / 0x4F / STS /TNS / TNS /1st_dataword_lo /1st_dataword_hi /.../last_dataword_lo /last_dataword_hi /DLE / ETX / CRC ]

[ DLE / ACK ]

DF1 Ack



CRC16 (Cyclic Redundancy Check)

The 16-bit cyclic redundancy check (CRC16) is a methodto check the integrity of a message packet. CRC16provides a higher level of data security than block checkcharacter.

Calculate the CRC value for master messages using thevalue of the STN, STX, data bytes, and the ETX (do notadd in the associated DLE for STX and ETX). Calculatethe CRC value for slave messages the same way, exceptDO NOT include the STX byte in the CRC calculation.

Important: To transmit the STN or data value of 10hex, you must use the data symbol DLEDLE. However, only one of these DLEdata bytes is included in the CRC value.

At the start of a message packet, the transmitter clears a16-bit register for the CRC value. As the first byte istransmitted, it is Exclusive-Or’ed (least significant bit tothe right) with the right eight bits of the CRC register.The result is placed back into the right eight bits of theCRC register.

The CRC register is then shifted right eight times byinserting 0x on the left. Each time a 1 is shifted out onthe right, the CRC register is Exclusive-OR’ed with thefollowing 16-bit binary constant:

CONSTANT = 1010 0000 0000 0001

The result is placed back into the CRC register. Afterthis shifting is completed, you are ready to transmit thenext byte.

As each additional byte is transmitted, it is included inthe value in the CRC register the same way. After theETX value is included in the value in the register and istransmitted, the value in the CRC register is transmitted(right bit first) as the CRC field.

The receiver also calculates the CRC value and comparesit to the received CRC value to verify the accuracy of thedata received.

The following structured English procedure shows thesteps involved in determining the CRC16 value.

data_byte = STN, STX, all application layer data, ETXCLEAR CRC_REGISTERFor each data_byte

Get data_byteXOR (data_byte, right 8 bits of CRC_REGISTER)PLACE RESULT in right 8 bits of CRC_REGISTERDO 8 times

Shift bit right, shift in 0 at leftIF bit shifted = 1

XOR (CONSTANT, CRC_REGISTER) PLACE RESULT in CRC_REGISTER

END IFEND DO

END FORTRANSMIT CRC_REGISTER as 2 byte CRC field

Examples

Example Destination Address = 123 (0x78)

Example Source Address = 0 (0x00)

Write

Device Configuration Data Table (Table 1 of DataTables)

Size = 44 words (88 bytes = 0x58)

C–5Serial Communication Protocol Tutorial


With table containing the following data:

Word # Data Word # Data

1 4 23 0

2 0 24 0

3 0 25 0

4 120 26 0

5 0 27 0

6 120 28 0

7 1000 29 1

8 0 30 1

9 5 31 100

10 10 32 5

11 0 33 6

12 1 34 1

13 125 35 3

14 0 36 0

15 5 37 0

16 1 38 0

17 1 39 0

18 0 40 0

19 1 41 1

20 0 42 2

21 0 43 0

22 1 44 0

Table C.5 Sample Write Sequence

Transmitted fromMaster



Communication Card

[ 10 / 01 / 7B / 10 / 02 /7B / 00 / 0F / 00 / 00 /00 / AA / 58 / 00 / 89 /00 / 00 / 04 / 00 / 00 /00 / 00 / 00 / 78 / 00 /00 / 00 / 78 / 00 / E8 /03 / 00 / 00 / 05 / 00 /0A / 00 / 00 / 00 / 01 /00 / 7D / 00 / 00 / 00 /05 / 00 / 01 / 00 / 01 /00 / 00 / 00 / 01 / 00 /00 / 00 / 00 / 00 / 01 /00 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 01 / 00 /01 / 00 / 64 / 00 / 05 /00 / 06 / 00 / 01 / 00 /03 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 00 / 00 /00 / 00 / 01 / 00 / 02 /00 / 00 / 00 / 00 / 00 /10 / 03 / 7E / AD ]

Write Data

DF1 Ack

[ 10 / 06 ]

[ 10 / 05 / 7B / 85 ]

Poll

ApplicationAck

[ 10 / 02 / 00 / 7B / 4F /00 / 00 / 00 / 10 / 03 /1F / 84 ]

[ 10 / 06 ]

DF1 Ack



Read

Diagnostic Data Table (Appendix ???, Table 20)

Size = 39 words (78 bytes = 0x4E)

With table containing the following data:

Word # Data Word # Data

1 96 23 1

2 1043 24 0

3 2309 25 0

4 1890 26 0

5 1403 27 5

6 11 28 0

7 9 29 0

8 0 30 0

9 0 31 0

10 0 32 0

11 0 33 0

12 0 34 123

13 0 35 0

14 0 36 0

15 0 37 0

16 1 38 0

17 261 39 0

18 17472

19 0

20 0

21 1

22 15

Table C.6 Sample Read Sequence

Transmitted fromMaster



Communication Card

[ 10 / 01 / 7B / 10 / 02 /7B / 00 / 0F / 00 / 00 /00 / A2 / 4E / 00 / 89 /00 / 00 / 10 / 03 / 4B /37 ]

ReadRequest

DF1 Ack

[ 10 / 06 ]

[ 10 / 05 / 7B / 85 ]

Poll

ApplicationAck

[ 10 / 02 / 00 / 7B / 4F /00 / 00 / 00 / 60 / 00 /13 / 04 / 05 / 09 / 62 /07 / 7B / 05 / 0B / 00 /09 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 01 / 00 /00 / F5 / 00 / 40 / 44 /00 / 00 / 00 / 00 / 01 /00 / 0F / 01 / 00 / 00 /00 / 00 / 00 / 00 / 00 /05 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 00 / 7B /00 / 00 / 00 / 00 / 00 /00 / 00 / 00 / 00 / 00 /00 / 10 / 03 / 61 / C0 ]

[ 10 / 06 ]

DF1 Ack

Appendix D


Sample Ladder Listing

Ladder Program Description

Appendix D contains sample ladder programs thatinterface to the Powermonitor II for PLC-5 R I/O,SLC-500 R I/O and SLC-500 RS-232. Because of thesimilarities of these three programs, only the PLC-5R I/O example operation is discussed in detail, and thedifferences in operation for the SLC-500 R I/O andSLC-500 RS-232 are noted. Rung-by-rung descriptionsare given for all three.

PLC-5 R I/O Operation

There are three modes of operation:

• Configuration

• Setpoint

• Run

Each mode uses a single Sequencer Output Instruction inorder to process the required block transfers. There areonly two block transfers required. These two blocktransfers are repeated until each mode is completedsuccessfully. For Run mode, the number of blocktransfers processed by the sequencer is variable. Becausethere is only one sequencer to be used for three modes,the sequencer’s input file must be updated at thebeginning of each new mode. The numberscorresponding to the block transfers required for eachmode are contained in three separate files. The contentof each file is moved to the sequencer’s input file at thebeginning of its corresponding mode.

Configuration Mode

During initialization of Configuration mode, thesequencer input file is loaded with the two numbers.These numbers correspond to the configuration tableBTW and the diagnostic table BTR. The sequencerlength is set to 2. After completion of the configurationdata BTW, a diagnostic table BTR is performed to verifythat the BTW was successful. If the configuration tableBTW is successful, the Configuration mode bit isunlatched and the setpoint mode bit is latched. If theBTW is not successful, the configuration table BTW anddiagnostic table BTR sequence continues until theproblem is corrected. This most likely requires a changein the configuration table data.

Setpoint Mode

During initialization of Setpoint mode, the sequencerinput file is loaded with the two numbers. Thesenumbers correspond to the setpoint data table BTW andthe diagnostic data table BTR. The sequencer length isset to 2. Also, the number of setpoints is written to acounter which is used to determine the address of the userpopulated setpoint data tables. After the completion ofthe setpoint BTW, a diagnostic table BTR is performed toverify the BTW was successful. If it was not successful,further setpoints will not be written until the setpoint datatable that caused the error is corrected. If all thesetpoints are written correctly, the Setpoint mode bit isunlatched, and the Run mode bit is latched.

Run Mode

During initialization of Run mode, the sequencer inputfile is loaded with the numbers corresponding to theblock transfers to be performed. Once Run mode hasbegun, the ladder program will remain in this mode.

Note: The speed with which the processor performsthe block transfers may be altered byrearranging or changing the size of the blocktransfer sequence. However, the availability ofnew data values is controlled by thePowermonitor II table update rate.

SLC-500 R I/O Operation

The SLC-500 R I/O requires more attention. BTW andBTR instructions subroutines have been developed forimplementation of the SLC-500 R I/O sample ladder.The BTR and BTW subroutines are patterned after theblock transfer examples shown in the R I/O Scanner UserManual ( Cat. No. 1747-SN, Publication 1747-6.6 –February 1995), pp. 5-23 to 5-28. Refer to this manualfor a more detailed description of how these blocktransfer routines work.

In addition to the two files that contain the BTR andBTW subroutines, there is a third subroutine file. Thisfile executes a small amount of initialization ladderbefore each block transfer subroutine.

D–2 Sample Ladder Listing


The SLC-500 R I/O version requires that all read andwrite tables be 64 words in length. This is a necessaryrequirement stemming from the use of the block transfersubroutines.

A four word length control file needs to be initialized foreach individual block transfer subroutine. Theinitialization values for each word are discussed in theData Files Used section.

SLC-500 RS-232 Operation

Use of an SLC-500 MSG instruction in place of the BTWand BTR instructions is the only difference between thePLC-5 R I/O and the SLC-500 RS-232 versions of thePowermonitor II sample ladder.

PLC-5 R I/O Data Files Used

Data FileAddress

Data FileSize

Description

B3 20 b3/0 Configuration mode enable

b3/2 Run mode enable

b3/1 Setpoint mode enable

b3/300 One-shot bit

b3/301 One-shot bit

b3/302 One-shot bit

b3/303 One-shot bit

b3/304 One-shot bit

N9 1 N9:0 Sequencer output

N10 variable N10:0 Sequencer input

Data FileAddress

Data FileSize

Description

N11 3 N11:0 Sequencer input data forconfiguration mode

N12 3 N12:0 Sequencer input data forsetpoint mode

N13 variable N13:0 Sequencer input data forrun mode

N20 2 N20:0 Number of setpoints

N20:1 Temporary storage forsetpoint address

N22 21 Setpoint #1 location

N23•••

21 Setpoint #2 location•••

N39 21 Setpoint #20 location

R6:0 Sequencer control

BTR Data Table Locations

(control / data)

N40 / N70 54 Voltage/current data

N41 / N71 63 Real-time power

N42 / N72 46 Cumulative power

N43 / N73 45 Device configuration

N44 / N74 31 Communication configuration

N45 / N75 43 Demand

N46 / N76 61 Even harmonic distortion

N47 / N77 62 Odd harmonic distortion

N48 / N78 59 Even harmonic magnitude

N49 / N79 58 Odd harmonic magnitude

N50 / N80 57 Even harmonic phase

N51 / N81 56 Odd harmonic phase

N52 / N82 40 Diagnostic

N53 / N83 39 Relay/setpoint

BTW Data Table Locations

(control / data)

N54 / N84 23 Command

N55 / N85 45 Device configuration

N56 / N86 21 Setpoint

Sequencer input file N10 contains a list of the blocktransfers required to complete the active mode. Thecontents of N10 are copied from N11 for Configurationmode, N12 for Setpoint mode and N13 for Run modeduring each mode’s initialization.

D–3Sample Ladder Listing


The reset word for the sequencer is N10:1. The firstword in the rotation of the sequencer N10:1. The valuein N10:0 must be the same as that in N10:1. This meansN11:0 must equal N11:1, N12:0 must equal N12:1 andN13:0 must equal N13:1. The size of file N10 is equal tothe size of the largest sequencer input file. Forconfiguration and setpoint modes, this size will always be2. In Run mode the size depends on the number of blocktransfers to be performed. The sequencer length may beexpanded or reduced for run mode. It is imperative thatthe corresponding file that serves as the source of thesequencer’s input file, N13, must be modifiedaccordingly.

Important: Failure to modify the length of file N13 fora modification of the run mode sequencersize will result in improper operation of therun mode block transfer ladder, andpossible FAULT of the processor due toinvalid indirect offsets.

File Data Values

Prior to running the sample ladder, each of the threesequencer initialization files need to be loaded with thenumbers that correspond to each mode’s block transfersequence. The following is a list of each mode’sinitialization file and the required/possible numbers to bestored in each. The first value of a block transfersequence must be duplicated in both position 0 and 1 ofan initialization file.

N11 – Configuration Mode

Required numbers are 55, 55, and 52.

N12 – Setpoint Mode

Required numbers are 56, 56, and 52.

N13 – Run Mode

Possible numbers are 40, 41, 42, 43, 44, 45, 46, 47, 48,49, 50, 51, 52, 53, 54, 55, 56

SLC-500 R I/O Data Files Used

There are three differences between the SLC-500 R I/Oand PLC-5 implementations of the sample ladder.

1. All BTR and BTW control files are four words inlength and need to be initialized. For control file x,this initialization is:

x:0 = block transfer control bits (M0 “control flags”)See R I/O Scanner User Manual, Publication1747-6.6. (Bit 0 = BTW; Bit 7 = BTR)

x:1 = block transfer size

x:2 = SLC-5 logical address (logical rack, group andslot) See R I/O Scanner User Manual.

x:3 = data file location

For example, the control file for a configuration tableBTW, file 55 should be initialized to:

55:0 = 0 (BTW)

55:1 = 44 (Configuration table block transfer size)

55:2 = 100 (Logical rack 1, group 0, slot 0)

55:3 = 85 (Configuration table data file)

2. All data storage files for BTR and BTW subroutineexecution are 64 words in length.

3. The SLC-500 R I/O block transfer subroutine N15,requires a file that is eight words in length. In thisexample N15 is used. No initialization is required.

SLC-500 RS-232 Data Files Used

Same as PLC-5 R I/O.

Sample Ladder Listing

These example ladder programs show a way to configurethe block transfers for the Powermonitor II.

!ATTENTION: Proper operation of theladder program is the responsibility of theuser. No warranty is expressed or impliedby using these ladder configurations.

These ladders are subject to change.



PLC-5 R I/ORung 2:0 Enable configuration mode and clear one shot bits.| First-Pass Config || Bit Mode || S:1 B3 |+––––] [––––––––––––––––––––––––––––––––––––––––––––––––+–––––––––––––(L)––––+–+| 15 | 0 | || | Setpoint | || | Mode | || | B3 | || +–––––––––––––(U)––––+ || | 1 | || | Run | || | Mode | || | B3 | || +–––––––––––––(U)––––+ || | 2 | || | Clear | || | One Shots | || |+CLR–––––––––––––––+| || ++CLEAR ++ || ||Destination B3:18|| || || 1000000000000000|| || |+––––––––––––––––––+| || |+CLR–––––––––––––––+| || ++CLEAR ++ || |Destination B3:19| || | 0000000000000000| || +––––––––––––––––––+ |Rung 2:1 Initialize for appropriate mode.| First–Pass Initialize || Bit Sequencer || Input File || S:1 +COP–––––––––––––––+ |+––––] [–––––––––––––––––––––––––––––––––––––––––––+–––––+COPY FILE ++–+| 15 | |Source #N11:0|| || | |Destination #N10:0|| || | |Length 3|| || | +––––––––––––––––––+| || | Initialize | || | Sequencer | || | Length | || |+MOV––––––––––––––––––––+| || ++MOVE ++ || ||Source 2|| || || || || ||Destination R6:0.LEN|| || || 7|| || |+–––––––––––––––––––––––+| || | Initialize | || | Sequencer | || | Position | || |+CLR––––––––––––––––––––+| || ++CLEAR ++ || ||Destination R6:0.POS|| || || 5|| || |+–––––––––––––––––––––––+| || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+| || +–––––+MOVE ++ || |Source N10:0| || | 40| || |Destination N9:0| || | 40| || +––––––––––––––––––+ |

Rung 2:0

Latch configuration mode andunlatch setpoint and run modes.Clear one-shot bits.

Rung 2:1

Initialize the sequencer forconfiguration mode. Thisincludes loading the sequencerinput file with the configurationblock transfer numbers, settingthe sequencer length, clearingthe sequencer position andmoving the reset word into thesequencer’s output file.



Rung 2:2 Begin setpoint mode once configuration is complete.| Config |Config |Status Status – Status – Config || Mode |BTW |BTR Bad Table Bad Param. Mode || |Done |Done Check Check || B3 N55:0 N52:0 +CMP–––––––––––––+ +CMP–––––––––––––+ B3 |+––] [–––––] [–––––] [–––+COMPARE +–+COMPARE ++–––––––(U)––––+–+| 0 13 13 |Expression | |Expression || 0 | || |N82:36 = 0 | |N82:37 = 0 || Setpoint | || +––––––––––––––––+ +––––––––––––––––+| Mode | || | B3 | || +–––––––(L)––––+ || 1 | Rung 2:3 Initialize for appropriate mode.| Setpoint |One Shot 1 Initialize || Mode | Sequencer || Input File || B3 B3 +COP–––––––––––––––+ |+––––] [–––––––[ONS]–––––––––––––––––––––––––––––––+–––––+COPY FILE ++–+| 1 300 | |Source #N12:0|| || | |Destination #N10:0|| || | |Length 3|| || | +––––––––––––––––––+| || | Initialize | || | Sequencer | || | Length | || |+MOV––––––––––––––––––––+| || ++MOVE ++ || ||Source 2|| || || || || ||Destination R6:0.LEN|| || || 7|| || |+–––––––––––––––––––––––+| || | Initialize | || | Sequencer | || | Position | || |+CLR––––––––––––––––––––+| || ++CLEAR ++ || ||Destination R6:0.POS|| || || 5|| || |+–––––––––––––––––––––––+| || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+| || +–––––+MOVE ++ || |Source N10:0| || | 40| || |Destination N9:0| || | 40| || +––––––––––––––––––+ |Rung 2:4 Load number of setpoints into setpoint counter.| Setpoint |One Shot 2 Number of || Mode | Setpoints || B3 B3 +MOV––––––––––––––––––––+ |+––––] [–––––––[ONS]–––––––––––––––––––––––––––––––++MOVE ++–+| 1 301 ||Source N20:0|| || || 3|| || ||Destination C5:0.PRE|| || || 3|| || |+–––––––––––––––––––––––+| || | C5:0| || +––––––––––––––––––––(RES)+ || |

Rung 2:2

If the configuration BTW anddiagnostic BTR are done, checkthat the diagnostic tableparameters indicate a successfulBTW (word 36 and 37 equal 0).If so, unlatch the configurationmode bit and latch the setpointmode bit.

Rung 2:3

Initialize the sequencer forsetpoint mode. Samefunctionality as Rung 2:0.

Rung 2:4

Move the number of setpointsinto the setpoint addresscounter. Reset the setpointcounter.



Rung 2:5 Initialize for appropriate mode.| Run |One Shot 3 Initialize || Mode | Sequencer || Input File || B3 B3 +COP–––––––––––––––+ |+––––] [–––––––[ONS]–––––––––––––––––––––––––––––––+–––––+COPY FILE ++–+| 2 302 | |Source #N13:0|| || | |Destination #N10:0|| || | |Length 8|| || | +––––––––––––––––––+| || | Initialize | || | Sequencer | || | Length | || |+MOV––––––––––––––––––––+| || ++MOVE ++ || ||Source 7|| || || || || ||Destination R6:0.LEN|| || || 7|| || |+–––––––––––––––––––––––+| || | Initialize | || | Sequencer | || | Position | || |+CLR––––––––––––––––––––+| || ++CLEAR ++ || ||Destination R6:0.POS|| || || 5|| || |+–––––––––––––––––––––––+| || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+| || +–––––+MOVE ++ || |Source N10:0| || | 40| || |Destination N9:0| || | 40| || +––––––––––––––––––+ |Rung 2:6 Main block transfer sequencer.| BT || Done || Bit || N[N9:0]:0 R6:0 +SQO–––––––––––––––+ |+–+–––] [––––+–]/[–––––––––––––––––––––––––––––––––––+SEQUENCER OUTPUT +–(EN)–+| | 13 | EN |File #N10:0| || |BT | |Mask FFFF+–(DN) || |Error | |Destination N9:0| || |Bit | |Control R6:0| || |N[N9:0]:0 | |Length 7| || +–––] [––––+ |Position 5| || 12 +––––––––––––––––––+ |Rung 2:7| Voltage/ || Current || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 40 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N40:0+–(ER) || |Data file N70:1| || |Length 53| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:8| Real–Time || Power || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 41 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N41:0+–(ER) || |Data file N71:1| || |Length 62| || |Continuous N| || +–––––––––––––––––––––––+ |

Rung 2:5

Initialize the sequencer for runmode. Same functionality asRungs 2:0 and 2:1.

Rung 2:6

This is the main block transfersequencer. The sequenceroutput word, N9:0, is updatedwhenever the previous blocktransfer is done or fails.

Rung 2:7

Voltage/current BTR.

Rung 2:8

Real time power BTR.



Rung 2:9| Cumulative || Power || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 42 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N42:0+–(ER) || |Data file N72:1| || |Length 45| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:10| Device || Config || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 43 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N43:0+–(ER) || |Data file N73:1| || |Length 44| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:11| Comm. || Config || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 44 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N44:0+–(ER) || |Data file N74:1| || |Length 30| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:12| Demand || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 45 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N45:0+–(ER) || |Data file N75:1| || |Length 42| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:13| Even || Harmonic || Distortion || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 46 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N46:0+–(ER) || |Data file N76:1| || |Length 60| || |Continuous N| || +–––––––––––––––––––––––+ |

Rung 2:9

Cumulative power BTR.

Rung 2:10

Device configuration BTR.

Rung 2:11

Communication configurationBTR.

Rung 2:12

Demand BTR.

Rung 2:13

Even harmonic distortion BTR.



Rung 2:14| Odd || Harmonic || Distortion || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 47 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N47:0+–(ER) || |Data file N77:1| || |Length 61| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:15| Even || Harmonic || Magnitude || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 48 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N48:0+–(ER) || |Data file N78:1| || |Length 58| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:16| Odd || Harmonic || Magnitude || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 49 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N49:0+–(ER) || |Data file N79:1| || |Length 57| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:17| Even || Harmonic || Phase || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 50 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N50:0+–(ER) || |Data file N80:1| || |Length 56| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:18| Odd || Harmonic || Phase || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 51 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N51:0+–(ER) || |Data file N81:1| || |Length 55| || |Continuous N| || +–––––––––––––––––––––––+ |

Rung 2:14

Odd harmonic distortion BTR.

Rung 2:15

Even harmonic magnitudeBTR.

Rung 2:16

Odd harmonic magnitude BTR.

Rung 2:17

Even harmonic phase BTR.

Rung 2:18

Odd harmonic phase BTR.



Rung 2:19| Diagnostic || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 52 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N52:0+–(ER) || |Data file N82:1| || |Length 39| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:20| Relay/ || Setpoint || BTR || +CMP–––––––––––––––+ +BTR––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER READ +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 53 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N53:0+–(ER) || |Data file N83:1| || |Length 38| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:21| Command || BTW || +CMP–––––––––––––––+ +BTW––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER WRITE +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 54 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N54:0+–(ER) || |Data file N84:1| || |Length 22| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:22| Config || BTW || +CMP–––––––––––––––+ +BTW––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER WRITE +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 55 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N55:0+–(ER) || |Data file N85:1| || |Length 44| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:23 Begin run mode once all setpoint block transfers are complete.| One Shot 4 Status – Setpoint Setpoint || Bad Table Counter Mode || Check Done Bit || +CMP–––––––––––––––+ B3 +CMP–––––––––––––––+ C5:0 B3 |+–+COMPARE +–––[ONS]––––+COMPARE +––––] [–––––+–––(U)––––+–+| |Expression | 303 |Expression | DN | 1 | || |N9:0 = 56 | |N82:36 = 0 | |Run | || +––––––––––––––––––+ +––––––––––––––––––+ |Mode | || | B3 | || +–––(L)––––+ || 2 |

Rung 2:19

Diagnostic BTR.

Rung 2:20

Relay/setpoint BTR.

Rung 2:21

Command BTW.

Rung 2:22

Configuration BTW.

Rung 2:23

If the setpoint counter done bitis set, the last setpoint BTW hasoccurred and was followed by adiagnostic BTR. If thediagnostic table indicates asuccessful setpoint BTW,setpoint mode is done. Thesetpoint mode bit is unlatched,and the run mode bit is latched.



Rung 2:24 Load next setpoint into setpoint write data location.| One Shot 5 Status – Setpoint Setpoint || Bad Table Counter Number || Check Done Bit || +CMP–––––––––+ B3 +CMP–––––––––––+ C5:0 +CTU––––––––––––+ |+–+COMPARE +–––[ONS]–––+++COMPARE ++–––]/[–––+COUNT UP +–(CU)+–+| |Expression | 304 |||Expression || DN |Counter C5:0| | || |N9:0 = 56 | |||N82:36 = 0 || |Preset 3+–(DN)| || +––––––––––––+ ||+––––––––––––––+| |Accum 3| | || || Prepare | +–––––––––––––––+ | || || Initial | | || || Setpoint | | || || Write | | || ||+CMP–––––––––––+| | || |++COMPARE ++ | || | |Expression | | || | |C5:0.ACC = 0 | | || | +––––––––––––––+ | || | Setpoint | || | Data | || | Address | || |+ADD–––––––––––––––+ | || ++ADD +–––––––––––––––––––––––––––––+ || ||Source A 21| | || || | | || ||Source B C5:0.ACC| | || || 3| | || ||Destination N20:1| | || || 24| | || |+––––––––––––––––––+ | || | | || | | || | | || | | || | | || | | || | | || | | || | | || | | || | | || | | || | | || | | | | | | | | | Move | || | Current | || | Setpoint | || | Data into | || | BTW Table | || |+COP–––––––––––––––+ | || ++COPY FILE +–––––––––––––––––––––––––––––+ || |Source #N[N20:1]:1| || |Destination #N86:1| || |Length 20| || +––––––––––––––––––+ | Rung 2:25| Setpoint || BTW || +CMP–––––––––––––––+ +BTW––––––––––––––––––––+ |+–+COMPARE +––––––––––––––––––––––––––+BLOCK TRANSFER WRITE +–(EN)–+| |Expression | |Rack 01| || |N9:0 = 56 | |Group 0+–(DN) || +––––––––––––––––––+ |Module 0| || |Control block N56:0+–(ER) || |Data file N86:1| || |Length 20| || |Continuous N| || +–––––––––––––––––––––––+ |Rung 2:26| |+––––––––––––––––––––––––––––––––[END OF FILE]–––––––––––––––––––––––––––––––––+| |

Rung 2:24

This rung is activated oncewhen the sequencer output filechanges to setpoint BTW. Itspurpose is to determine theaddress of the next setpoint dataand to copy the data residing atthis address into the setpointBTW data location. This isaccomplished by first adding anaddress offset to a base addressto determine the location of thenext setpoint data. The dataresiding at the resulting addressis then transferred to thesetpoint BTW data location. Acounter is used to determine theaddress offset. Prior to the firstsetpoint BTW, the counter isautomatically incremented. Forsubsequent setpoint BTWs, thecounter is incremented whenthe diagnostic table BTR for theprevious setpoint BTW issuccessful. For example, the3rd setpoint will reside at baseaddress 24. In this case, acounter value of 3 will be addedto the base address 21. Thedata residing at location 24 willthen be transferred into thesetpoint BTW data locationN86:1.

Rung 2:25

Setpoint BTW.

Rung 2:26

End of file.



Rung 2:0 Enable configuration mode and clear one shot bits.| First Config || Pass Mode || S:1 B3 ||––––] [––––––––––––––––––––––––––––––––––––––––––––––+––––(L)–––––––––––––––+–|| 15 | 0 | || | Setpoint | || | Mode | || | B3 | || +––––(U)–––––––––––––––+ || | 1 | || | Run | || | Mode | || | B3 | || +––––(U)–––––––––––––––+ || | 2 | || | Clear | || | One Shots | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest B3:18| | || | | 0100000000000000| | || | +––––––––––––––––––+ | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || |Dest B3:19| || | 0000000000000000| || +––––––––––––––––––+ |Rung 2:1 Initialize for appropriate mode.| First Initialize || Pass Sequencer || Input File || S:1 +COP–––––––––––––––+ ||––––] [––––––––––––––––––––––––––––––––––––––––––––––+–+COPY FILE +–+–|| 15 | |Source #N11:0| | || | |Dest #N10:0| | || | |Length 3| | || | +––––––––––––––––––+ | | | | | || | Initialize | || | Sequencer | || | Length | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source 2| | || | | | | || | |Dest R6:0.LEN| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Position | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest R6:0.POS| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source N10:0| | || | | 40| | || | |Dest N9:0| | || | | 40| | || | +––––––––––––––––––+ | || | BT Done | || | Bit | || | N[N9:0]:0 | || +––––(U)–––––––––––––––+ || | 13 | || | Prepare | || | For BT | || | +JSR–––––––––––––––+ | || +–+JUMP TO SUBROUTINE+–+ || |SBR file number 5| || +––––––––––––––––––+ |

SLC-500 R I/ORung 2:0


Rung 2:1

Initialize the sequencer forconfiguration mode. Thisincludes loading the sequencerinput file with the configurationblock transfer numbers, settingthe sequencer length, clearingthe sequencer position andmoving the reset word into thesequencer’s output file. Also,the sequencer’s output file donebit is unlatched to insure thatthe next rung is not activeimmediately and the blocktransfer preparation subroutineis called.



Rung 2:2 Begin setpoint mode once configuration is complete.| Config |Config |Status Status – Config || Mode |BTW |BTR Bad Table Mode || |Done |Done Check || B3 N55:0 N52:0 +EQU–––––––––––––––+ B3 ||––––] [––––––––] [––––––––] [–––––+EQUAL +–––––––––+––––(U)–––––+–|| 0 13 13 |Source A N82:36| | 0 | || | 0| | | || |Source B 0| | | || | | | | || +––––––––––––––––––+ | | || | Setpoint | || | Mode | || | B3 | || +––––(L)–––––+ || 1 |Rung 2:3 Initialize for appropriate mode.| Setpoint |One Shot 1 Initialize || Mode | Sequencer || Input File || B3 B3 +COP–––––––––––––––+ ||––––] [–––––––[OSR]––––––––––––––––––––––––––––––––––+–+COPY FILE +–+–|| 1 300 | |Source #N12:0| | || | |Dest #N10:0| | || | |Length 3| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Length | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source 2| | || | | | | || | |Dest R6:0.LEN| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Position | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest R6:0.POS| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source N10:0| | || | | 40| | || | |Dest N9:0| | || | | 40| | || | +––––––––––––––––––+ | || | Prepare | || | For BT | || | +JSR–––––––––––––––+ | || +–+JUMP TO SUBROUTINE+–+ || |SBR file number 5| || +––––––––––––––––––+ |Rung 2:4 Load number of setpoints into setpoint counter.| Setpoint |One Shot 2 Number Of || Mode | Setpoints || B3 B3 +MOV–––––––––––––––+ ||––––] [–––––––[OSR]––––––––––––––––––––––––––––––––––+–+MOVE +–+–|| 1 301 | |Source N20:0| | || | | 3| | || | |Dest C5:0.PRE| | || | | 3| | || | +––––––––––––––––––+ | || | C5:0 | || +––(RES)–––––––––––––––+ || |

Rung 2:2


Rung 2:3


Rung 2:4




Rung 2:5 Initialize for appropriate mode.| Run |One Shot 3 Initialize || Mode | Sequencer || Input File || B3 B3 +COP–––––––––––––––+ ||––––] [–––––––[OSR]––––––––––––––––––––––––––––––––––+–+COPY FILE +–+–|| 2 302 | |Source #N13:0| | || | |Dest #N10:0| | || | |Length 4| | || | +––––––––––––––––––+ | | | | | || | Initialize | || | Sequencer | || | Length | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source 3| | || | | | | || | |Dest R6:0.LEN| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Position | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest R6:0.POS| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source N10:0| | || | | 40| | || | |Dest N9:0| | || | | 40| | || | +––––––––––––––––––+ | || | Prepare | || | For BT | || | +JSR–––––––––––––––+ | || +–+JUMP TO SUBROUTINE+–+ || |SBR file number 5| || +––––––––––––––––––+ |Rung 2:6 Main block transfer sequencer.| BT Done || Bit || N[N9:0]:0 R6:0 +SQO–––––––––––––––+ ||–+––––] [–––––+––]/[––––––––––––––––––––––––––––+–+SEQUENCER OUTPUT +–(EN)–+–|| | 13 | EN | |File #N10:0+–(DN) | || | | | |Mask FFFF| | || | | | |Dest N9:0| | || | | | |Control R6:0| | || | | | |Length 3| | || | | | |Position 1| | || | | | +––––––––––––––––––+ | || | BT Error | | Prepare | || | Bit | | For BT | || | N[N9:0]:0 | | +JSR–––––––––––––––+ | || +––––] [–––––+ +–+JUMP TO SUBROUTINE+––––––+ || 12 |SBR file number 5| || +––––––––––––––––––+ |Rung 2:7 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 40| || | | || +––––––––––––––––––+ |

Rung 2:5

Initialize the sequencer for runmode. Same functionality asRungs 2:0 and 2:1.

Rung 2:6

This is the main block transfersequencer. The sequenceroutput word, N9:0, is updatedwhenever the previous blocktransfer is done or fails. Aftereach sequencer increment, theblock transfer preparationsubroutine is called.

Rung 2:7




Rung 2:8 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 41| || | | || +––––––––––––––––––+ |Rung 2:9 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 42| || | | || +––––––––––––––––––+ |Rung 2:10 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 43| || | | || +––––––––––––––––––+ |Rung 2:11 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 44| || | | || +––––––––––––––––––+ |Rung 2:12 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 45| || | | || +––––––––––––––––––+ |Rung 2:13 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 46| || | | || +––––––––––––––––––+ |Rung 2:14 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 47| || | | || +––––––––––––––––––+ |Rung 2:15 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 48| || | | || +––––––––––––––––––+ |Rung 2:16 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 49| || | | || +––––––––––––––––––+ |

Rung 2:8


Rung 2:9


Rung 2:10


Rung 2:11


Rung 2:12

Demand BTR.

Rung 2:13


Rung 2:14


Rung 2:15


Rung 2:16




Rung 2:17 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 50| || | | || +––––––––––––––––––+ |Rung 2:18 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 51| || | | || +––––––––––––––––––+ |Rung 2:19 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 52| || | | || +––––––––––––––––––+ |Rung 2:20 Perform appropriate block transfer read.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 3| || | 40| +––––––––––––––––––+ || |Source B 53| || | | || +––––––––––––––––––+ |Rung 2:21 Perform appropriate block transfer write.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 4| || | 40| +––––––––––––––––––+ || |Source B 54| || | | || +––––––––––––––––––+ |Rung 2:22 Perform appropriate block transfer write.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 4| || | 40| +––––––––––––––––––+ || |Source B 55| || | | || +––––––––––––––––––+ |Rung 2:23 Begin run mode once all setpoint block transfers are complete.| One Shot 4 Status – Setpoint Setpoint || Bad Table Counter Mode || Check Done Bit || +EQU–––––––––––––––+ B3 +EQU–––––––––––––––+ C5:0 B3 ||–+EQUAL +–––[OSR]––––+EQUAL +––––] [–––+––––(U)–––––+–|| |Source A N9:0| 303 |Source A N82:36| DN | 1 | || | 40| | 0| | | || |Source B 56| |Source B 0| | | || | | | | | | || +––––––––––––––––––+ +––––––––––––––––––+ | | || | Run | || | Mode | || | B3 | || +––––(L)–––––+ || 2 |

Rung 2:17


Rung 2:18


Rung 2:19

Diagnostic BTR.

Rung 2:22

Configuration BTW.

Rung 2:20

Relay/setpoint BTR.

Rung 2:21

Command BTW.

Rung 2:23




Rung 2:24 Load next setpoint into setpoint write data location.| One Shot 5 Status – Setpoint Setpoint || Bad Table Counter Number || Check Done Bit || +EQU––––––––––+ B3 +EQU––––––––––––––+ C5:0 +CTU––––––––––––+ ||–+EQUAL +–[OSR]–+–+–+EQUAL +–+–]/[–+COUNT UP +–(CU)–+–|| |Source A N9:0| 304| | |Source A N82:36| | DN|Counter C5:0+–(DN) | || | 40| | | | 0| | |Preset 3| | || |Source B 56| | | |Source B 0| | |Accum 3| | || | | | | | | | +–––––––––––––––+ | || +–––––––––––––+ | | +–––––––––––––––––+ | | || | | Prepare | | || | | Initial | | || | | Setpoint | | || | | Write | | || | | +EQU––––––––––––––+ | | || | +–+EQUAL +–+ | || | |Source A C5:0.ACC| | || | | 3| | || | |Source B 0| | || | | | | || | +–––––––––––––––––+ | || | Setpoint | || | Data | || | Address | || | +ADD–––––––––––––––+ | || +––––––––––––––––––––––––––+ADD +––––––+ || | |Source A 21| | || | | | | || | |Source B C5:0.ACC| | || | | 3| | || | |Dest N20:1| | || | | 24| | || | +––––––––––––––––––+ | || | Move | || | Current | || | Setpoint | || | Data Into | || | BTW Table | || | +COP–––––––––––––––+ | || +––––––––––––––––––––––––––+COPY FILE +––––––+ || |Source #N[N20:1]:1| || |Dest #N86:1| || |Length 20| || +––––––––––––––––––+ |

Rung 2:25 Perform appropriate block transfer write.| +EQU–––––––––––––––+ +JSR–––––––––––––––+ ||–+EQUAL +––––––––––––––––––––––––––––––––––––+JUMP TO SUBROUTINE+–|| |Source A N9:0| |SBR file number 4| || | 40| +––––––––––––––––––+ || |Source B 56| || | | || +––––––––––––––––––+ |Rung 2:26| ||–––––––––––––––––––––––––––––––––––––+END+––––––––––––––––––––––––––––––––––––|| |

Rung 2:26

End of file.

Rung 2:24


Rung 2:25

Setpoint BTW.



BTR and BTW Subroutines

The SLC-500 R I/O BTR and BTW subroutines mimicthe read and write block transfer examples listed in theback of the Publication 1747–6.6, R I/O Scanner UserManual. The following rung descriptions and notespertain to modifications or additions to these examples.

1. The BTR and BTW subroutines use different files andbits than those given in the R I/O Scanner Manual.The substitutions are:

B3:0 – B3:5 are replaced by N15:0 – N15:4

B3:100 is replaced by the control word correspondingto the sequencer’s output file ( N[N9:0]:0 ).

2. The file M0.1 is used for the BTW while file M0.2 isused for the BTR routine.

3. The first rung of the block transfer examples in the Publication 1747–6.6, R I/O Scanner User Manual isnot used in the BTR and BTW subroutines. This isbecause the function performed by that rung,initializing the control flags for the M file blocktransfer, is done in the BTR or BTW subroutine at thetime the BTR and BTW block transfer are initiated.These control flags, which are moved into the M filecontrol buffers at the block transfer initiation, areinitialized for each control file associated with blocktransfer operations ( see Data Files Used section ).

BTR ( File 3 )

Rung 3:0| Service BT Status || The BT || Status/ || BT || Pending || +SBR–––––––––––––––+ N15:5 +COP–––––––––––––––+ ||–+SUBROUTINE +–+––––] [–––––+–––––––––––––––––––––+COPY FILE +–|| +––––––––––––––––––+ | 0 | |Source #M1:2.100| || | | |Dest #N15:0| || | | |Length 4| || | | +––––––––––––––––––+ || | Check BT | || | Status | || | Until DN | || | or ER Bit | || | Is Off | || | N15:5 | || +––––] [–––––+ || 1 |Rung 3:1| Virtual Check BT || BT Done Status || Bit Until DN || or ER Bit || Is Off || N15:0 N15:5 ||–+––––]/[–––––+–––––––––––––––––––––––––––––––––––––––––––––––––––––––(U)–––––|| | 13 | 1 || | Virtual | || | BT Err | || | Bit | || | N15:0 | || +––––]/[–––––+ || 12 |

Rung 3:0

Copy the BTR status area to afile which will be usedthroughout the program. Thisavoids addressing the M1 filemultiple times during eachprogram scan. Each time aninstruction containing an M1file bit, word or file is scannedby the processor, an immediatedata transfer to the moduleoccurs and therefore will impactthe overall processor time.

Rung 3:1

Unlatch the bit that continues tocheck the BTR status. When aBTR is complete, the done bit isset. The ladder program mustunlatch the enable bit, then waitfor the SN module to turn offthe done bit before another BTRto the same M-file location canbe initiated.



Rung 3:2| Virtual BT Data || BT Done || Bit || N15:0 +COP–––––––––––––––+ ||––––] [––––––––––––––––––––––––––––––––––––––––––––––+–+COPY FILE +–+–|| 13 | |Source #M1:2.110| | || | |Dest #N[N15:7]:1| | || | |Length 63| | || | +––––––––––––––––––+ | | | | | || | Service | || | The BT | || | Status/ | || | BT | || | Pending | || | N15:5 | || +––––(U)–––––––––––––––+ || | 0 | || | BT enable | || | bit | || | N[N9:0]:0 | || +––––(U)–––––––––––––––+ || | 15 | || | Check BT | || | Status | || | Until DN | || | or ER Bit | || | Is Off | || | N15:5 | || +––––(L)–––––––––––––––+ | Rung 3:3 1| Virtual BT Error || BT Err Code || Bit || N15:0 +MOV–––––––––––––––+ ||––––] [––––––––––––––––––––––––––––––––––––––––––––––+–+MOVE +–+–|| 12 | |Source N15:3| | || | | 0| | || | |Dest N15:4| | || | | 0| | || | +––––––––––––––––––+ | || | Service | || | The BT | || | Status/ | || | BT | || | Pending | || | N15:5 | || +––––(U)–––––––––––––––+ || | 0 | || | BT enable | || | bit | || | N[N9:0]:0 | || +––––(U)–––––––––––––––+ || | 15 | | | | | || | Check BT | || | Status | || | Until DN | || | or ER Bit | || | Is Off | || | N15:5 | || +––––(L)–––––––––––––––+ || | 1 | || | BT Error | || | Bit | || | N[N9:0]:0 | || +––––(L)–––––––––––––––+ || 12 |

Rung 3:2

When a BTR successfullycompletes, buffer the BT dataand unlatch the BT enable bit.As shown, 63 words are copiedto the BTR destination file,beginning at word 1, in order tomatch the Powermonitor II datatable layout. Also, unlatch theBTR pending bit and latch thebit that continues checking theBTR status until the SN moduleturns off the done bit.

Rung 3:3

If a BTR error occurs, unlatchthe enable bit and buffer the BTerror code. Also, unlatch theBTR pending bit, latch the bitthat continues checking theBTR status until the SN moduleturns off the error bit and latchthe control word error bit.



Rung 3:4| BT |BT enable |Virtual |Virtual BT Done || Initiate |bit |BT Done |BT Err Bit || Bit | |Bit |Bit || N15:6 N[N9:0]:0 N15:0 N15:0 N[N9:0]:0 ||––––] [––––––––]/[––––––––]/[––––––––]/[–––––––––––––––––––––––+––––(U)–––––+–|| 0 15 13 12 | 13 | || | BT Error | || | Bit | || | N[N9:0]:0 | || +––––(U)–––––+ || | 12 | || | Service | || | The BT | || | Status/ | || | BT | || | Pending | || | N15:5 | || +––––(L)–––––+ || | 0 | || | BT enable | || | bit | || | N[N9:0]:0 | || +––––(L)–––––+ || | 15 | || | BT | || | Initiate | || | Bit | || | N15:6 | || +––––(U)–––––+ || 0 | Rung 3:5| BT enable || bit || N[N9:0]:0 +COP–––––––––––––––+ ||–+––––] [–––––+––––––––––––––––––––––––––––––––––––––––––+COPY FILE +–|| | 15 | |Source #N[N9:0]:0| || | | |Dest #M0:2.100| || | | |Length 3| || | | +––––––––––––––––––+ || | Virtual | || | BT Done | || | Bit | || | N15:0 | || +––––] [–––––+ || | 13 | || | Virtual | || | BT Err | || | Bit | || | N15:0 | || +––––] [–––––+ || 12 |Rung 3:6| BT enable |BT |Virtual |Virtual BT Error BT Done || bit |Initiate |BT Done |BT Err Code Bit || |Bit |Bit |Bit || N[N9:0]:0 N15:6 N15:0 N15:0 +EQU–––––––––––––––+ N[N9:0]:0 ||––––]/[––––––]/[––––––]/[–––––––]/[–––––+–+EQUAL +––––––(L)–––––+–|| 15 0 13 12 | |Source A N15:4| 13 | || | | 0| | || | |Source B 0| | || | | | | || | +––––––––––––––––––+ | || | BT Error BT Error | || | Code Bit | || | +NEQ–––––––––––––––+ N[N9:0]:0 | || +–+NOT EQUAL +––––––(L)–––––+ || |Source A N15:4| 12 || | 0| || |Source B 0| || | | || +––––––––––––––––––+ |Rung 3:7| +RET–––––––––––––––+ ||–––––––––––––––––––––––––––––––––––––––––––––––––––––––––+RETURN +–|| +––––––––––––––––––+ |Rung 3:8| ||–––––––––––––––––––––––––––––––––––––+END+––––––––––––––––––––––––––––––––––––|| |

Rung 3:4

When a new BTR is initiated,latch the enable bit, as long as aBTR is not in progress. Also,latch the BTR pending bit, sothe BTR status file will be BTRby the ladder program. Becausethis rung marks the beginningof the BTR, both the done anderror bits for the block transfercontrol word are unlatchedalong with the block transferinitiate bit.

Rung 3:5

Move the virtual control wordsto the M0 file for the SNmodule whenever a transition ofthe BTR enable bit occurs.

Rung 3:6

If all the conditions of this rungare true, the BTR cycle iscomplete. Latch the controlword done bit if the error wordat N15:4 is clear, or the controlword error bit if it is not.

Rung 3:7

Return from subroutine.

Rung 3:8

End of file.



BTW ( File 4 )Rung 4:0| Service BT Status || The BT || Status/ || BT || Pending || +SBR–––––––––––––––+ N15:5 +COP–––––––––––––––+ ||–+SUBROUTINE +–+––––] [–––––+–––––––––––––––––––––+COPY FILE +–|| +––––––––––––––––––+ | 0 | |Source #M1:2.200| || | | |Dest #N15:0| || | | |Length 4| || | | +––––––––––––––––––+ || | Check BT | || | Status | || | Until DN | || | or ER Bit | || | Is Off | || | N15:5 | || +––––] [–––––+ || 1 |Rung 4:1| Virtual Check BT || BT Done Status || Bit Until DN || or ER Bit || Is Off || N15:0 N15:5 ||–+––––]/[–––––+–––––––––––––––––––––––––––––––––––––––––––––––––––––––(U)–––––|| | 13 | 1 || | Virtual | || | BT Err | || | Bit | || | N15:0 | || +––––]/[–––––+ || 12 |Rung 4:2| Virtual Service || BT Done The BT || Bit Status/ || BT || Pending || N15:0 N15:5 ||––––] [––––––––––––––––––––––––––––––––––––––––––––––––––––––––+––––(U)–––––+–|| 13 | 0 | | | | | || | BT enable | || | bit | || | N[N9:0]:0 | || +––––(U)–––––+ || | 15 | || | Check BT | || | Status | || | Until DN | || | or ER Bit | || | Is Off | || | N15:5 | || +––––(L)–––––+ || 1 |

Rung 4:0

Copy the BTW status area to afile which will be usedthroughout the program, onlywhen a BTW is pending. Thisavoids accessing the M1 filemultiple times during each scan.Each time an instructioncontaining an M1 file bit, wordor file is scanned by theprocessor, an immediate datatransfer to the module occursand therefore will impact theprocessor scan time.

Rung 4:1

Unlatch the bit that continues tocheck the BTW status. When aBTW is complete, the done bitis set. The ladder must thenunlatch the enable bit, then waitfor the SN module to turn offthe done bit before anotherBTW to the same M-filelocation can be initialized.

Rung 4:2

When a BTW successfullycompletes, unlatch the BTWenable bit. Also, unlatch theBTW pending bit and unlatchthe bit that continues checkingthe BTW status until the SNmodule turns off the done bit.



Rung 4:3| Virtual BT Error || BT Err Code || Bit || N15:0 +MOV–––––––––––––––+ ||––––] [––––––––––––––––––––––––––––––––––––––––––––––+–+MOVE +–+–|| 12 | |Source N15:3| | || | | 0| | || | |Dest N15:4| | || | | 0| | || | +––––––––––––––––––+ | || | Service | || | The BT | || | Status/ | || | BT | || | Pending | || | N15:5 | || +––––(U)–––––––––––––––+ || | 0 | || | BT enable | || | bit | || | N[N9:0]:0 | || +––––(U)–––––––––––––––+ || | 15 | || | Check BT | || | Status | || | Until DN | || | or ER Bit | || | Is Off | || | N15:5 | || +––––(L)–––––––––––––––+ || | 1 | | | | | || | BT Error | || | Bit | || | N[N9:0]:0 | || +––––(L)–––––––––––––––+ || 12 |Rung 4:4| BT |BT enable |Virtual |Virtual BT Done || Initiate |bit |BT Done |BT Err Bit || Bit | |Bit |Bit || N15:6 N[N9:0]:0 N15:0 N15:0 N[N9:0]:0 ||––––] [––––––––]/[––––––––]/[––––––––]/[–––––––––––––+––––(U)–––––––––––––––+–|| 0 15 13 12 | 13 | || | BT Error | || | Bit | || | N[N9:0]:0 | || +––––(U)–––––––––––––––+ || | 12 | || | +COP–––––––––––––––+ | || +–+COPY FILE +–+ || | |Source #N[N15:7]:1| | || | |Dest #M0:2.210| | || | |Length 63| | || | +––––––––––––––––––+ | || | Service | || | The BT | || | Status/ | || | BT | || | Pending | || | N15:5 | || +––––(L)–––––––––––––––+ || | 0 | || | BT enable | || | bit | || | N[N9:0]:0 | || +––––(L)–––––––––––––––+ || | 15 | || | BT | || | Initiate | || | Bit | || | N15:6 | || +––––(U)–––––––––––––––+ || 0 |

Rung 4:3

If a BTW errors, unlatch theenable bit, the BTW pending bitand buffer the BTW error code.Also, latch the bit that continueschecking the BTW status untilthe SN module turns off theerror bit and latch the controlword error bit.

Rung 4:4

When a new BTW is initiated,copy the data to the M0 file dataarea and latch the virtual BTWenable bit provided that a BTWis not in progress. As shown,only 63 words of the BTW datafile are copied to the M filebuffer, beginning at word 1, inorder to match thePowermonitor II data tablelayout. Also, latch the BTWpending bit, so the BT statusfile will be read by the ladderprogram. And because thisrung marks the beginning of theBTW, unlatch the control worddone and error bits and the BTinitiate bit.



Rung 4:5| BT enable || bit || N[N9:0]:0 +COP–––––––––––––––+ ||–+––––] [–––––+––––––––––––––––––––––––––––––––––––––––––+COPY FILE +–|| | 15 | |Source #N[N9:0]:0| || | | |Dest #M0:2.200| || | | |Length 3| || | | +––––––––––––––––––+ || | Virtual | || | BT Done | || | Bit | || | N15:0 | || +––––] [–––––+ || | 13 | || | Virtual | || | BT Err | || | Bit | || | N15:0 | || +––––] [–––––+ || 12 |Rung 4:6| BT enable |BT |Virtual |Virtual BT Error BT Done || bit |Initiate |BT Done |BT Err Code Bit || |Bit |Bit |Bit || N[N9:0]:0 N15:6 N15:0 N15:0 +EQU–––––––––––––––+ N[N9:0]:0 ||––––]/[–––––––]/[––––––]/[––––––]/[–––––+–+EQUAL +––––––(L)–––––+–|| 15 0 13 12 | |Source A N15:4| 13 | || | | 0| | || | |Source B 0| | || | | | | || | +––––––––––––––––––+ | || | BT Error BT Error | || | Code Bit | || | +NEQ–––––––––––––––+ N[N9:0]:0 | || +–+NOT EQUAL +––––––(L)–––––+ || |Source A N15:4| 12 || | 0| || |Source B 0| || | | || +––––––––––––––––––+ |Rung 4:7| +RET–––––––––––––––+ ||–––––––––––––––––––––––––––––––––––––––––––––––––––––––––+RETURN +–|| +––––––––––––––––––+ |Rung 4:8| ||–––––––––––––––––––––––––––––––––––––+END+––––––––––––––––––––––––––––––––––––|| |

Rung 4:5

Move the virtual control wordsto the M0 file for the SNmodule whenever a transition ofthe BTW enable bit occurs.

Rung 4:8

End of file.

Rung 4:7


Rung 4:6

If all the conditions of this rungare true, the BTW cycle iscomplete. Latch the controlword done bit if the error wordat N15:4 is clear, or the controlword error bit if it is not.



BT Preparation ( File 5 )Rung 5:0| Clear || BT || File || +SBR–––––––––––––––+ +FLL–––––––––––––––+ ||–+SUBROUTINE +––––––––––––––––––––––––––––––––+–+FILL FILE +–+–|| +––––––––––––––––––+ | |Source 0| | || | |Dest #N15:0| | || | |Length 7| | || | +––––––––––––––––––+ | || | Move | || | BT Data | || | Location | || | Into BT | || | File | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source N[N9:0]:3| | || | | | | || | |Dest N15:7| | || | | 70| | || | +––––––––––––––––––+ | || | BT | || | Initiate | || | Bit | || | N15:6 | || +––––(L)–––––––––––––––+ || | 0 | || | BT enable | || | bit | || | N[N9:0]:0 | || +––––(U)–––––––––––––––+ || 15 |Rung 5:1| +RET–––––––––––––––+ ||–––––––––––––––––––––––––––––––––––––––––––––––––––––––––+RETURN +–|| +––––––––––––––––––+ |Rung 5:2| ||–––––––––––––––––––––––––––––––––––––+END+––––––––––––––––––––––––––––––––––––|| |

Rung 5:0

In preparation for execution of ablock transfer, this rung clearsthe 8 words of file N15, movesthe BT data table location intoword N15:7, latches the BTinitiate bit and unlatches the BTenable bit.

Rung 5:1


Rung 5:2

End of file.



SLC–500 RS-232Rung 2:0 Enable configuration mode and clear one shot bits.| First Config || Pass Mode || S:1 B3 ||––––] [––––––––––––––––––––––––––––––––––––––––––––––+––––(L)–––––––––––––––+–|| 15 | 0 | || | Setpoint | || | Mode | || | B3 | || +––––(U)–––––––––––––––+ || | 1 | || | Run | || | Mode | || | B3 | || +––––(U)–––––––––––––––+ || | 2 | || | Clear | || | One Shots | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest B3:18| | || | | 0100000000000000| | || | +––––––––––––––––––+ | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || |Dest B3:19| || | 0000000000000000| || +––––––––––––––––––+ |Rung 2:1 Initialize for appropriate mode.| First Initialize || Pass Sequencer || Input File || S:1 +COP–––––––––––––––+ ||––––] [––––––––––––––––––––––––––––––––––––––––––––––+–+COPY FILE +–+–|| 15 | |Source #N11:0| | || | |Dest #N10:0| | || | |Length 3| | || | +––––––––––––––––––+ | | | || | Initialize | || | Sequencer | || | Length | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source 2| | || | | | | || | |Dest R6:0.LEN| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Position | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest R6:0.POS| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || |Source N10:0| || | 40| || |Dest N9:0| || | 40| || +––––––––––––––––––+ |

Rung 2:0


Rung 2:1

Initialize the sequencer forconfiguration mode. Thisincludes loading the sequencerinput file with the configurationblock transfer numbers, settingthe sequencer length, clearingthe sequencer position andmoving the reset word into thesequencer’s output file.



Rung 2:2 Begin setpoint mode once configuration is complete.| Config |Config |Status Status – Config || Mode |BTW |BTR Bad Table Mode || |Done |Done Check || B3 N55:0 N52:0 +EQU–––––––––––––––+ B3 ||––––] [––––––––] [––––––––] [–––––+EQUAL +–––––––––+––––(U)–––––+–|| 0 13 13 |Source A N82:36| | 0 | || | 0| | | || |Source B 0| | | || | | | | || +––––––––––––––––––+ | | || | Setpoint | || | Mode | || | B3 | || +––––(L)–––––+ || 1 |Rung 2:3 Initialize for appropriate mode.| Setpoint |One Shot 1 Initialize || Mode | Sequencer || Input File || B3 B3 +COP–––––––––––––––+ ||––––] [–––––––[OSR]––––––––––––––––––––––––––––––––––+–+COPY FILE +–+–|| 1 300 | |Source #N12:0| | || | |Dest #N10:0| | || | |Length 3| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Length | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source 2| | || | | | | || | |Dest R6:0.LEN| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Position | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest R6:0.POS| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || |Source N10:0| || | 40| || |Dest N9:0| || | 40| || +––––––––––––––––––+ |Rung 2:4 Load number of setpoints into setpoint counter.| Setpoint |One Shot 2 Number of || Mode | Setpoints || B3 B3 +MOV–––––––––––––––+ ||––––] [–––––––[OSR]––––––––––––––––––––––––––––––––––+–+MOVE +–+–|| 1 301 | |Source N20:0| | || | | 3| | || | |Dest C5:0.PRE| | || | | 3| | || | +––––––––––––––––––+ | || | C5:0 | || +––(RES)–––––––––––––––+ || |

Rung 2:2


Rung 2:3


Rung 2:4




Rung 2:5 Initialize for appropriate mode.| Run |One Shot 3 Initialize || Mode | Sequencer || Input File || B3 B3 +COP–––––––––––––––+ ||––––] [–––––––[OSR]––––––––––––––––––––––––––––––––––+–+COPY FILE +–+–|| 2 302 | |Source #N13:0| | || | |Dest #N10:0| | || | |Length 3| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Length | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || | |Source 1| | || | | | | || | |Dest R6:0.LEN| | || | | 1| | || | +––––––––––––––––––+ | || | Initialize | || | Sequencer | || | Position | || | +CLR–––––––––––––––+ | || +–+CLEAR +–+ || | |Dest R6:0.POS| | || | | 1| | || | +––––––––––––––––––+ | | | | | || | Initialize | || | Sequencer | || | Address | || | +MOV–––––––––––––––+ | || +–+MOVE +–+ || |Source N10:0| || | 40| || |Dest N9:0| || | 40| || +––––––––––––––––––+ |Rung 2:6 Main block transfer sequencer.| BT || Done || Bit || N[N9:0]:0 R6:0 +SQO–––––––––––––––+ ||–+––––] [–––––+––]/[––––––––––––––––––––––––––––––––+SEQUENCER OUTPUT +–(EN)–|| | 13 | EN |File #N10:0+–(DN) || | | |Mask FFFF| || | | |Dest N9:0| || | | |Control R6:0| || | | |Length 1| || | | |Position 1| || | | +––––––––––––––––––+ || | BT | || | Error | || | Bit | || | N[N9:0]:0 | || +––––] [–––––+ || 12 |Rung 2:7| Voltage/ || Current || +EQU–––––––––––––––+ N40:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 40| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N40:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |

Rung 2:5

Initialize the sequencer for runmode. Same functionality asrungs 2:0 and 2:1.

Rung 2:6

This is the main block transfersequencer. The sequenceroutput word, N9:0, is updatedwhenever the previous blocktransfer is done or fails.

Rung 2:7




Rung 2:8| real time || Power || +EQU–––––––––––––––+ N41:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 41| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N41:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:9| Cumulative || Power || +EQU–––––––––––––––+ N42:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 42| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N42:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:10| Device || Config || +EQU–––––––––––––––+ N43:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 43| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N43:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:11| Comm. || Config || +EQU–––––––––––––––+ N44:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 44| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N44:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:12| Demand || +EQU–––––––––––––––+ N45:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 45| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N45:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:13| Even || Harmonic || Distortion || +EQU–––––––––––––––+ N46:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 46| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N46:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |

Rung 2:12

Demand BTR.

Rung 2:8


Rung 2:9


Rung 2:10


Rung 2:11


Rung 2:13




Rung 2:14| Odd || Harmonic || Distortion || +EQU–––––––––––––––+ N47:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 47| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N47:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:15| Even || Harmonic || Magnitude || +EQU–––––––––––––––+ N48:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 48| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N48:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:16| Odd || Harmonic || Magnitude || +EQU–––––––––––––––+ N49:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 49| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N49:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:17| Even || Harmonic || Phase || +EQU–––––––––––––––+ N50:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 50| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N50:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:18| Odd || Harmonic || Phase || +EQU–––––––––––––––+ N51:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 51| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N51:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:19| Diagnostic || +EQU–––––––––––––––+ N52:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 52| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N52:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |

Rung 2:17


Rung 2:14


Rung 2:15


Rung 2:16


Rung 2:19

Diagnostic BTR.

Rung 2:18




Rung 2:20| Relay/ || Setpoint || +EQU–––––––––––––––+ N53:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write READ+–(ER) || |Source B 53| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N53:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:21| Command || +EQU–––––––––––––––+ N54:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write WRITE+–(ER) || |Source B 54| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N54:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:22| Config || +EQU–––––––––––––––+ N55:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write WRITE+–(ER) || |Source B 55| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N55:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:23 Begin run mode once all setpoint block transfers are complete.| One Shot 4 Status – Setpoint Setpoint || Bad Table Counter Mode || Check Done Bit || +EQU––––––––––––––+ B3 +EQU–––––––––––––––+ C5:0 B3 ||–+EQUAL +–––[OSR]––––+EQUAL +––––] [––––+––––(U)–––––+–|| |Source A N9:0| 303 |Source A N82:36| DN | 1 | || | 40| | 0| | | || |Source B 56| |Source B 0| | | || | | | | | | || +–––––––––––––––––+ +––––––––––––––––––+ | | || | Run | || | Mode | || | B3 | || +––––(L)–––––+ || 2 |

Rung 2:22

Configuration BTW.

Rung 2:20

Relay/setpoint BTR.

Rung 2:21

Command BTW.

Rung 2:23




Rung 2:24 Load next setpoint into setpoint write data.| One Shot 5 Status – Setpoint Setpoint || Bad Table Counter Number || Check Done Bit || +EQU–––––––––––+ B3 +EQU–––––––––––––––+ C5:0 +CTU––––––––––+ ||–+EQUAL +–[OSR]–+–+–+EQUAL +–+–]/[–+COUNT UP +–(CU)–+–|| |Source A N9:0| 304| | |Source A N82:36| | DN |Counter C5:0+–(DN) | || | 40| | | | 0| | |Preset 3| | || |Source B 56| | | |Source B 0| | |Accum 3| | || | | | | | | | +–––––––––––––+ | || +––––––––––––––+ | | +––––––––––––––––––+ | | || | | Prepare | | || | | Initial | | || | | Setpoint | | || | | Write | | || | | +EQU–––––––––––––––+ | | || | +–+EQUAL +–+ | || | |Source A C5:0.ACC| | || | | 3| | || | |Source B 0| | || | | | | || | +––––––––––––––––––+ | || | Setpoint | || | Data | || | Address | || | +ADD–––––––––––––––+ | || +–––––––––––––––––––––––––+ADD +––––––+ || | |Source A 21| | || | | | | || | |Source B C5:0.ACC| | || | | 3| | || | |Dest N20:1| | || | | 24| | || | +––––––––––––––––––+ | || | Move | || | Current | || | Setpoint | || | Data into | || | BTW Table | || | +COP–––––––––––––––+ | || +–––––––––––––––––––––––––+COPY FILE +––––––+ || |Source #N[N20:1]:1| || |Dest #N86:1| || |Length 20| || +––––––––––––––––––+ |

Rung 2:25| Setpoint || +EQU–––––––––––––––+ N56:0 +MSG––––––––––––––––––––+ ||–+EQUAL +––]/[–––––––––––––––––––––+READ/WRITE MESSAGE +–(EN)–|| |Source A N9:0| 15 |Type PEER–TO–PEER+–(DN) || | 40| |Read/Write WRITE+–(ER) || |Source B 56| |Target Device 500CPU| || | | |Local/Remote LOCAL| || +––––––––––––––––––+ |Control Block N56:0| || |Control Block Length 14| || +–––––––––––––––––––––––+ |Rung 2:26| ||–––––––––––––––––––––––––––––––––––––+END+––––––––––––––––––––––––––––––––––––|| |

Rung 2:24


Rung 2:25

Setpoint BTW.

Rung 2:26

End of file.

Appendix E


Technical Specifications

Product Approvals

UL 508 Component Recognized File E96956 andCSA C22.2 approval for Industrial Control Equipment.

Compliance to European Union Directives

If this product has the CE mark it is approved forinstallation within the European Union and EEA regions.It has been designed and tested to meet the followingdirectives.

EMC Directive

This product is tested to meet Council Directive89/336/EEC Electromagnetic Compatibility (EMC) andthe following standards, in whole or in part, documentedin a technical construction file:

• EN 50081-2 – Generic Emission Standard, Part 2 –Industrial Environment

• EN 50082-2 – Generic Immunity Standard, Part 2 –Industrial Environment

This product is intended for use in an industrialenvironment.

Low Voltage Directive

This product is tested to meet Council Directive73/23/EEC Low Voltage, by applying the safetyrequirements of IEC 1010-1.

This equipment is classified as open equipment and mustbe installed (mounted) in an enclosure during operationas a means of providing safety protection.

Screw Torque and W ire Size

Position Ratings

Mounting Screw TighteningTorque

0.9 to 1.1 Nm (8 to 10 lb-in.)

Communications Connector 0.6 to 0.8 Nm (8 to 10 lb-in.)

Terminal Screw TighteningTorque

0.2 to 2.5 mm2 (24-12 AWG),stranded or solid wire, Cu wireonly.

Terminal Block/Wire InsulationTemperature Index

75° C maximum

Environmental Specifications

Operating Temperature –40° C to +60° C

Storage Temperature –40° C to +85° C

Humidity5 to 95 percent,non-condensing

Vibration

Operational: 0.006 in. DA/1.0 GSine, 10 to 500 Hz, 3orthogonal axes.

VibrationNon-operational: 0.015 in.DA/2.5 G Sine, 10 to 500 Hz, 3orthogonal axes.

Shock

Operational: 15 G, Half Sine,11 ms duration, 3 orthogonalaxes, 3 (+) and 3 (–)pulses/axes, 18 pulses total.

ShockNon-operational: 30 G, HalfSine, 11 ms duration, 3orthogonal axes, 3 (+) and 3 (–)pulses/axes, 18 pulses total.

E–2 Technical Specifications


Allen-Bradley, a Rockwell Automation Business, has been helping its customers improveproductivity and quality for more than 90 years. We design, manufacture and support a broadrange of automation products worldwide. They include logic processors, power and motioncontrol devices, operator interfaces, sensors and a variety of software. Rockwell is one of theworld’s leading technology companies.

Worldwide representation.

Argentina • Australia • Austria • Bahrain • Belgium • Brazil • Bulgaria • Canada • Chile • China, PRC • Colombia • Costa Rica • Croatia • Cyprus • Czech Republic •Denmark • Ecuador • Egypt • El Salvador • Finland • France • Germany • Greece • Guatemala • Honduras • Hong Kong • Hungary • Iceland • India • Indonesia • Ireland • Israel • Italy • Jamaica • Japan • Jordan • Korea • Kuwait • Lebanon • Malaysia • Mexico • Netherlands • New Zealand • Norway • Pakistan • Peru •Philippines • Poland • Portugal • Puerto Rico • Qatar • Romania • Russia–CIS • Saudi Arabia • Singapore • Slovakia • Slovenia • South Africa, Republic • Spain •Sweden • Switzerland • Taiwan • Thailand • Turkey • United Arab Emirates • United Kingdom • United States • Uruguay • Venezuela • Yugoslavia

Allen-Bradley Headquarters, 1201 South Second Street, Milwaukee, WI 53204 USA, Tel: (1) 414 382-2000 Fax: (1) 414 382-4444

Publication 1403-5.1 – January 1998Publication 1403-5.1 – January 1998Supersedes Publication 1403-5.1 October 1996

40055–162–01 (B)Copyright 1998. Rockwell International Corporation. All rights reserved. Printed in USA

manual power monitor nsc

Documents