lubri-cup™ automatic lubricant dispensers...the lubri-cup™ em automatic lubricant dispensers are...
TRANSCRIPT
Lubri-Cup™ Automatic Lubricant Dispensers
Correct lubrication, is critical to the performance of your industrial equipment. Reliability Engineers, Lubrication Technicians, Production and Process Managers are aware that lubrication is a crucial step and a wise investment to optimize equipment life. Chesterton lubricators can provide the best lubrication solutions for plant equipment. Both over- and under-lubrication, abrasive and water contamination can lead to premature bearing failure, costly repair and downtime. The best practice is to apply the correct engineered lubricant in small, metered amounts over a defined period of time. Chesterton Lubri-Cup™ is state-of-the-art, precision designed, cost effective alternative to manual lubrication of bearings used in electric motors, generators, compressors, fans and blowers, pumps, agitators and mixers. Lubri-Cup™ can also be used on slideways, linear actuators, open gears, rail systems, bushings and journals. The robust equipment design allows for use even in the harshest environments, found in the following applications in:
2
• Automotive Assembly• Automation & Robotics • Chemical and Petroleum • Food & Beverage
• Marine • Metal Processing, Smelting, Casting • Mining and Ore Processing• Oil and Gas
• Power Generation• Pulp and Paper • Water & Wastewater• Wood Processing
Lubri-Cup™ VG MiniChesterton® Lubri-Cup™ VG Mini is a 120cc automatic, single-point lubricator used to dispense Chesterton grease to critical areas while eliminating over- and under-greasing. The Lubri-Cup VG Mini is controlled with an electrochemical microprocessor, to offer superior advantages over conventional gas powered dispensers. The Lubri-Cup VG Mini is cost competitive and easy to use.
VG Mini Product Characteristics
• Easy to use, simple to install and operate• Variable dispensing rates: 1, 3, 6, 9, 12 months• Service Temperatures: -15°C to 60°C (5°F to 140°F) Alkaline Battery • Remote installation: up to 0,3 m (1ft)• Electrochemical operation, safe non-flammable nitrogen gas• Programmable with a single switch
Lubri-Cup™ VG
Chesterton® Lubri-Cup™ VG is a 250cc automatic, single-point lubricator used to dispense Chesterton grease at a controlled rate and interval. The Lubri-Cup VG pro-logic microprocessor chip control is easy to use and can be programmed by simply pressing a single button. Pressure is generated intermittently above the piston which delivers a fresh and precise amount of lubricant to your critical equipment. The VG is also certified for “intrinsic safety” Ex is IIC T4 for use in hazardous areas.
VG Product Characteristics
• Easy to use, simple to install and operate• Variable dispensing rates: 1, 3, 6, 12 months• Remote operation: up to 0,3 m (1ft)• Service Temperatures: -15°C to 60°C (5°F to 140°F) Alkaline Battery • Electrochemical operation, safe non-flammable nitrogen gas• Diagnostic LCD display• Programmable with a single switch• 250cc unit is programmable for 125cc or 250cc
3
Lubri-Cup™ VG Mini Ordering Information
Reorder Number Product Description
084473 Lubri-Cup™ VG Mini 120cc 630
084477 Lubri-Cup™ VG Mini 120cc 615#2
084492 Lubri-Cup™ VG Mini 120cc 635
Lubri-Cup™ VG Ordering Information
Reorder Number Product Description
084304 Lubri-Cup™ VG 250cc 615#1
084305 Lubri-Cup™ VG 250cc 615#2
084306 Lubri-Cup™ VG 250cc 630
084383 Lubri-Cup™ VG 250cc 635
084404 Lubri-Cup™ VG 250cc 633
VG Mini
VG
UL Certifications: Class I, Div I, Group A, B, C, DATEX: Ex ia IIC T4 GaIP: IP 68
UL Certifications: Class I, Div I, Group A, B, C, D Class II, Div I, Group E, F, GATEX: Ex ia IIc T4 GaIP: IP 68
Lubri-Cup™ EMChesterton® Lubri-Cup™ EM is an automatic, single-point or multiple point lubricant dispenser available in 250cc or 500cc sizes. The innovative Lubri-Cup EM dispenser is designed to ensure reliable lubrication and at the same time cut lubrication costs with an advanced computerized control system. It consists of a vertical positive displacement feed pump, motor/gear set, and microprocessor allowing typical operating pressure of 30kgf/cm² (425psi) or up to 60kfg/cm² (850psi) when needed. Lubri-Cup EM is ideal for hard to reach/ hazardous locations via its remote installation capability.
EM Product Characteristics
• Easy to use, simple to install and operate • Programmable: Operates up to 12 months, or 24 months ( See page 9 for details)• Replaceable grease service packs with Alkaline or Lithium Battery packs• Service Temperature: -15°C to 60°C (5°F to 140°F) Alkaline Battery
-40°C to 60°C (-40°F to 140°F) Lithium Battery• Lubricates up to 8 bearings - up to 6m (19ft)• Single point dispensing up to 10m (33ft)• Diagnostic LCD Display push Button Setting• 250cc unit is programmable for 125cc or 250cc
Lubri-Cup™ EM-S & EM-SP
Same great features of the Lubri-Cup EM, with the ability to operate in synchronization when installed on stand by or intermittently operated equipment. The unit will dispense the preset amount of grease only when the machine is operating. Lubri-Cup EM-S and SP units go into ‘stand by’ mode until the equipment returns to operation. EM-S utilizes the internal battery for power and synchronizes via an external switch. The EM-SP is externally powered by the equipment or PLC. There is no need to replace the battery pack for up to 5 years.
4
EM-S EM-SP
EM
Lubri-Cup™ EM-S & EM-SP Base Unit Only* Ordering Information
Reorder Number Product Description
084309 Lubri-Cup™ EM-S 250cc (Relay Box Included)
084311 Lubri-Cup™ EM-SP 250cc (DC Power Supply Included)
EM-S & EM-SP Product Characteristics• Programmable - operates up to 12 months, (See page 9 for details)• Replaceable grease service packs with Alkaline or Lithium Battery• Lubricates up to 8 bearings - up to 6m (19ft) away• Single point dispensing up to 10m ( 33ft)• Service Temperature: -15°C to 60°C (5°F to 140°F) Alkaline Battery
-40°C to 60°C (-40°F to 140°F) Lithium Battery• Diagnostic LCD Display push Button Setting• 250cc unit is programmable for 125cc or 250cc
Lubri-Cup™ EM Base Unit Only* Ordering Information
Reorder Number Product Description
084307 Lubri-Cup™ EM 250cc
084510 Lubri-Cup™ EM 500cc
*Order grease service packs separately
*Order grease service packs separately
Lubri-Cup™ EM-X
Chesterton® Lubri-Cup™ OL 500 Oiler is our latest innovation in oil lubrication specifically designed to deliver a fresh, consistent, and precise amount of oil to all of the vital parts of your rotating equipment. The precise and reliable lubrication of the OL 500 significantly reduces wear, oil consumption, and also extends the service life of your machinery; thus cutting high maintenance costs dramatically. The OL 500 is easily refillable.
OL 500 Oiler Product Characteristics• Microprocessor-controlled “pulse” delivery system• Programmable - operates up to 12 months• Service Temperature: -15°C to 60°C (5°F to 140°F) Alkaline Battery
-40°C to 60°C (-40°F to 140°F) Lithium Battery• Refillable - oil order separately• Lubricates up to 4 points• Sealed microprocessor
5
Lubri-Cup™ OL 500 Oiler* Ordering Information
Reorder Number Product Description
084319 Lubri-Cup™ OL 500cc Oiler
084457 Lubri-Cup™ OL 500-SP Oiler w/AC power
084464 Lubri-Cup™ OL 500-SP Oiler w/DC power
EM-X
OL 500
UL Certifications: Class I, Div II, Group C, DATEX: EEx nL IIB T5 IP54IP: IP 54
Chesterton® Lubri-Cup™ EM-X -Same great design as the Lubri-Cup EM and is specially designed with a modified enclosure rated for limited hazardous locations UL Class I, Div. II, Sec. C, D. and ATEX EEx nL IIB T5, IP 54. Operating pressure to 15Kgf (210 psi), for single point lubrication only.
Lubri-Cup™ OL 500 Oiler
EM-X Product Characteristics
• Easy to use, simple to install and operate• Programmable: operates up to 12 months, (see page 8 for details)• Replaceable grease service packs with Alkaline battery• Single point lubrication up to 3m (10ft) • Service Temperature: -15°C to 60°C (5°F to 140°F) Alkaline Battery• Diagnostic LCD Display push button setting• 250cc unit is programmable for 125cc or 250cc
Lubri-Cup™ EM-S & EM-SP Base Unit Only* Ordering Information
Reorder Number Product Description
084309 Lubri-Cup™ EM-S 250cc (Relay Box Included)
084311 Lubri-Cup™ EM-SP 250cc (DC Power Supply Included)
Lubri-Cup™ EM-X Base Unit Only* Ordering Information
Reorder Number Product Description
084308 Lubri-Cup™ EM-X 250cc
(Class I) Approved for Flammable Gas, Liquids and Solids, (Div 2) where ignitable concentrations of flammable. Materials are not likely to exist under normal conditions. (Group C, D) Tested safe with Ethylene and Propane gas.
*Order grease service packs separately
*Order replacement batteries separately
Lubri-Cup™ EM Service Packs
The Lubri-Cup™ EM automatic lubricant dispensers are developed to last multiple cycles through the use of replaceable service packs. As a result, one of the most significant benefits of the Lubri-Cup™ electromechanical lubricators is the substantial accumulated savings over the cost of manual lubrication while providing assurance of the most precise and reliable lubrication quality.
Replaceable Service Pack includes :
• A grease pouch of with Chesterton grease and volume of 250 or 500cc• An OEM battery pack: Standard DC 4.5V Alkaline or Optional DC 4.5V Lithium• A disposable dust cover and grease label
Keep Service Pack stored in a cool and dark place. The grease pouch and battery pack must always be replaced together at the end of each lubrication cycle to ensure reliable operation and guaranteed performance of the lubricator.
6
Lubri-Cup™ EM Service Pack Offerings
Reorder Number Lubri-Cup™ Model Chesterton® Grease Battery Type
EM 250cc Alkaline Battery
084313 EM 250cc 615 #1 Alkaline
084314 EM 250cc 615 #2 Alkaline
084315 EM 250cc 625 Alkaline
084312 EM 250cc 630 Alkaline
084316 EM 250cc 633 Alkaline
084317 EM 250cc 635 Alkaline
EM 250cc Lithium Battery
084392 EM 250cc 615 #1 Lithium
084393 EM 250cc 615 #2 Lithium
084393 EM 250cc 615 #2 Lithium
084379 EM 250cc 630 Lithium
084424 EM 250cc 635 Lithium
EM 500cc Alkaline Battery
084515 EM 500cc 615 #1 Alkaline
084516 EM 500cc 615 #2 Alkaline
084521 EM 500cc 630 Alkaline
084511 EM 500cc 635 Alkaline
EM 500cc Lithium Battery
084591 EM 500cc 615 # 2 - 460 Lithium
084519 EM 500cc 615 #2 Lithium
084535 EM 500cc 625 Lithium
084526 EM 500cc 635 Lithium
Grease Compatibility
613 615 622 625 629 630 633 635Aluminum Complex I A C A I A A ABarium Complex I C I C C C C CCalcium Stearate A C I C I C C CCalcium 12 Hydroxy C A C A A A A ACalcium Complex I I I I C I I ICalcium Sulfonate A C A C I C C CClay Non-soap I I I I A I I ILithium Stearate C A I A I A A ALithium 12 Hydroxy C A I A I A A ALithium Complex C C C C I C C CPolyurea, Conventional I I I I I I I IPolyurea, Shear Stable C C C C I C C C
Legend and Grease Change RecommendationsC = Compatible A = Borderline I = Incompatible
New grease can be applied as normal without purging, cleaning or flushing lines or bearing housings.
Centralized grease lines should be disconnected and the new grease pumped through. Grease in bearing housing does not need be removed. Manual greasing can be done as normal without additional consideration. Expect 10% change in grease thickness until all old grease is worked through.
All grease lines and bearings must be purged of the old greasebefore installing the new grease. Some bearing designs havedrain plugs which can be removed and the new grease pushedthrough until seen at the drain.
7
Speed Factor Grease Base Oil Viscosity
100,000-400,000 613 22075,000-300,000 615#1, #2 100<50,000 615 #2-460 46050,000-300,000 622 10050,000-300,000 629 220150,000-800,000 630 46200,000-800,000 633 32150,000-500,000 635 100
To Calculate Speed Factor NDm= RPM X (D1+D2)/2
Grease Selection Guide - Bearing Speed
Consistency of grease and base oil viscosity is effected by temperature, for service temperatures < 0°C (32°F) or > 150°C (302°F) consult factoryFor information on setting mode based on RPM, see page 8For Lubri-Cup dispensing mode and volume settings pages 8-9
D2 (mm)
D1 (mm)
Chesterton® greases have been tested and found to be compatible with many popular thickener technologies. The correct Chesterton grease can be selected from the charts below to optimize bearing performance and equipment life.
Determine the NDm or Speed Factor for your application. Select the appropriate Chesterton grease according to the Speed Factor range.
Mode Setting Guides
Electric Motors (ONLY) Lubri-Cup Mode Setting Guide, 250cc UnitsShaft SizeDia(mm)
RPM
100-500 500-1750 1750-3600 >3600
<35 12/125, 2PT* 9/125, 2PT* 12/125 12/125
36-51 9/125, 2 PT* 12/125 9/125 9/125
52-65 12/125 9/125 9/125 12
66-76 9/125 12 12 9
77-90 12 12 9 6
91-102 6 6 6 3
103-165 3 3 3 3
• *NOTE Due to small bearing size, a 2 Point Divider Block is used.• Due to variables in application conditions, always confirm specific setting with Chesterton Application Engineering. • For specific setting in CC/day, Please consult Chesterton Application Engineering. • Due to variables in application conditions (Temperature, Moisture, pH, Load and Vibration) greasing volumes may
be increased or decreased based on level of foreign particle contamination, degradation, and chemical attack.• Setting are approximations based on operating temperatures 10°-50°C (50°F - 122°F), Clean, Dry conditions using Chesterton Grease. • Temperatures over 50°C (122°F), Reduce setting by 50% per 10°C increase. (Ex. 12 to 6 ) • Temperatures below 0°C (32°F), Increase setting by 2X per 10C° decrease. (Ex. 3 to 6 )
Lubri-Cup Mode Setting Guide, 250/500cc UnitsShaft SizeDia(mm)
RPM
<100 100-500 500-1250 1250-3000 >3000
<35 12/125 12/125 9/125 12 9
36-51 12/125 12/125 9/125 12 9
52-65 9/125 12 9 6 6
66-76 12 12 9 9 6
77-90 12 9 6 6 3
91-120 9 9 4 4 1
121-165 6 6 3 1 NA
166-189 4 4 2 1/500 NA
190-230 3 1 1/500 NA NA
231-330 2 1/500 H/500 NA NA
• Due to variables in application conditions, always confirm specific setting with Chesterton Application Engineering.• For specific setting in CC/day, Please consult Chesterton Application Engineering. • Due to variables in application conditions (Temperature, Moisture, pH, Load and Vibration) greasing volumes may be increased or
decreased based on level of foreign particle contamination, degradation, and chemical attack. • Please Verify RPM for ALL LARGE BORE BEARINGS, >166mm, 6.5 in due to speed restrictions. • Setting are approximations based on operating temperatures 10°-50°C (50°F - 122°F), Clean, Dry conditions using Chesterton Grease. • Temperatures over 50°C (122°F), Reduce setting by 50% per 10°C increase. (Ex. 12 to 6 ) • Temperatures below 0°C (32°F), Increase setting by 2X per 10°C decrease. (Ex. 3 to 6 )• NA - Not Acceptable due to excess speed.
8
Lubri-Cups may be set to the desired dispensing Mode (Monthly) setting based on an approximation of Shaft Diameter and RPM. The selection guides are based on clean, dry and mechanically sound equipment conditions operating between 0°C (32°F) and 50°C (122°F). Please read all precautionary statements associated with the tables.
As Electric Motors require significantly less grease than Housing or Pillow Block mounted bearings, please use the Electric Motor chart below.
9
Dispensing Volume Guides
Mode/Month
EM, EM-X, EM-SP 125cc
EM, EM-X, EM-SP 250cc
OL-500, EM-500 500cc
Cycles cc/day Cycles cc/day Cycles cc/day
Half 24 8.3 48 16.7 96 33.4
1 12 4.1 24 8.3 48 16.7
2 6 2.8 12 5.6 24 8.3
3 4 2.1 8 4.2 NA NA
4 3 1.05 6 2.1 12 4.1
5 2.6 0.83 5 1.7 NA NA
6 2 0.7 4 1.4 8 2.8
7 1.7 0.6 3.5 1.2 NA NA
8 1.5 0.5 3 1.0 NA NA
9 1.4 0.45 2.8 0.9 NA NA
10 1.2 0.42 2.2 0.8 NA NA
11 1.1 0.38 2.2 0.75 NA NA
12 1 0.35 2 0.7 4 1.4
18 NA NA NA NA 3 0.93
24 NA NA NA NA 0 0.7
Mode/Month
VG Mini 120cc
VG 250cc
EM-S 250cc
Cycles cc/day Cycles cc/day Cycles cc/day
P = (Half) 24 8.3 48 16.7 48 16.7
1 12 4.1 24 8.3 24 8.3
2 NA NA 12 5.6 12 5.6
3 4 2.1 8 4.2 8 4.2
6 2 0.7 4 1.4 4 1.4
9 1.4 0.45 NA NA NA NA
12 1 0.35 2 0.7 2 0.7
Lubri-Cups can be set to the desired dispensing volume based on bearing size, rpm and operational conditions. The selection guides indicate the volume of grease dispensed based on the Mode (Monthly) setting. The volume of grease needed for the bearing may be found in your equipment guide/manual. For more specific quantity and frequency recommendations, Chesterton Technical Services can provide a tailored recommendation based on actual running conditions.
• Due to variables in application conditions, always confirm specific setting with Chesterton Application Engineering.• For specific setting in CC/day, Please consult Chesterton Application Engineering. • Due to variables in application conditions (Temperature, Moisture, pH, Load and Vibration) greasing volumes may be increased or
decreased based on level of foreign particle contamination, degradation, and chemical attack.
• Due to variables in application conditions, always confirm specific setting with Chesterton Application Engineering.• For specific setting in CC/day, Please consult Chesterton Application Engineering. • Due to variables in application conditions (Temperature, Moisture, pH, Load and Vibration) greasing volumes may be increased or
decreased based on level of foreign particle contamination, degradation, and chemical attack.
10
Remote multi-point lubrication is available with the Lubri-Cup EM using a divider block. It is recommended to test the back pressure of the bearing, lube lines, and divider block after assembly using a grease gun connected to a pressure gauge. Ensure the break-off pressure is below the average operating pressure of 30kgf/cm2 (425psi). Flow is directed as the valve responds to pump actuation. (See diagram). The Lubri-Cup EM and Divider Block allows for remote installation up to 6m (20ft). Safety, Reliability, and Simplicity with the Lubri-Cup EM and Divider Block system.
Multi-Point Remote Installation Warnings: For remote installation, keep the maximum distance at 6m (20ft) or less.
Do not plug any open ports on the divider block. The kit or divider block must be ordered with the appropriate number of points required. For more information on the divider block,please refer to the Multi-Point Remote Installation Manual. Use the lithium battery pack for specific applications such as: extremely cold temperature,long period mode setting (18M,24M), or multi-point remote installation for EM 500ml unit.
Remote Installation - Divider Blocks
The Chesterton Lubri-Cup EM, EM-S and EM-SP are powerful enough to dispense lubricating grease up to 8 bearing points. The available DIVIDER BLOCK is internally chambered and features a series of progressive/sequential valves to direct the lubricant to desired bearing.
For additional information on remote installation/divider blocks, please consult Chesterton Application Engineering.
Product Model Lubricant Volume Dimensions
Available Dispensing
Period
Max. Lube Points
Remote Installation
Operating Pressure
Operating Temperature
Range
Certifications & Approvals
Lubri-Cup™ VG Mini 120cc
�77mm (Ø.381”) x 140mm
(5.51”)
1, 3, 6, 9, 12 Months Single Point up to 1m (3ft) Max. 5kgf/
cm2 (70psi)-20°C ~ 55°C
(-4°F ~ 131°F)
UL: Class I, Div I, Group A, B, C, D. Class II, Div I, Group E, F, GATEX: Ex ia IIc T4 GaIP: IP68
Lubri-Cup™ VG 250cc
�97mm (Ø.381”) x 166mm
(6.54”)
1, 2, 3, 6, 12 months &
purgeSingle Point up to 1m (3ft) Max. 5kgf/
cm2 (70psi)-20°C ~ 55°C
(-4°F ~ 131°F)
UL: Class I, Div I, Group A, B, C, DATEX: Ex ia IIC T4 GaIP: IP 68
Lubri-Cup™ EM
250cc (Programmable
to 125cc)
�91mm (Ø.358”) x 262mm
(8.27”)
Half (H) 1, 2, 3, 6, 12
Up to 8 Points
up to 6m (20ft) per
point, 10m (33ft) single
point
Max. 60kgf/cm2 (850psi)
-15°C ~ 60°C(5°F ~ 140°F)
-40°C ~ 60°C(-40°F ~ 140°F)
with lithium battery pack
500cc
�92mm (Ø.362”) x 262mm
(8.27”)
Half (H) 1, 2, 3, 6, 12 18 & 24 months
Up to 8 Points
up to 6m (20ft) per
point , 10m (33ft) single
point
Max. 60kgf/cm2 (850psi)
-15°C ~ 60°C(5°F ~ 140°F)
-40°C ~ 60°C(-40°F ~ 140°F)
with lithium battery pack
Lubri-Cup™ EM-S & EM-SP
250cc (Programmable
to 125cc)
�91mm (Ø.358”) x 210mm
(8.26”)
EM-S Half (H) 1, 2, 3, 6, 12
EM-SP Half (H) 1 to 12,
1 month intevals
Up to 8 Points
up to 6m (20ft) per
point, 10m (33ft) single
point
Max. 60kgf/cm2 (850psi)
-15°C ~ 60°C(5°F ~ 140°F)
-40°C ~ 60°C(-40°F ~ 140°F)
with lithium battery pack
Lubri-Cup™ EM-X 250cc
�91mm (Ø.358”) x 210mm
(8.27”)
Half (H) 1 To 12
1 month intervals
Single Point Only
Single point only up to 3m
(10ft)
Max 15kgf/cm2 (200psi)
-15°C ~ 60°C(5°F ~ 140°F)
UL: Class I, Div II, Group C, DATEX: EEx nL IIB T5 IP54IP: IP54
Lubri-Cup™ OL 500 Oiler 500cc
�94mm (Ø.370”) x 235mm
(9.25”)
Half (H) 1, 2, 3, 6, 12 18 & 24 months
Up to 4 Points
Up to 12m (40ft) per
point
Avg. 10kgf/cm2(142psi)
-15°C ~ 60°C(5°F ~ 140°F)
-40°C ~ 60°C(-40°F ~ 140°F)
with lithium battery pack
Lubri-Cup™ Products - Feature Summary
E
Select the Lubri-Cup dispenser that best fulfills your application need. Chesterton Technical Service Engineers and Field Support Staff are always available to assist you.
11
Technical Data reflects results of laboratory tests and is intended to indicate general characteristics only. Since many actual application circumstances are beyond Chesterton's knowledge and/or control, the product user must determine the suitability of the products it intends to use for its particular purpose and assume all risks and liabilities in connection therewith. CHESTERTON DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
11/16
860 Salem Street, Groveland, MA 01834 USA978-469-6888 www.chesterton.com© 2016 A.W. Chesterton Company ® Registered trademark owned and licensed by
A.W. Chesterton Company in USA and other countries, unless otherwise noted.
Global Solutions, Local Service
Since its founding in 1884, the A.W. Chesterton Company hassuccessfully met the critical needs of its diverse customer base.Today, as always, customers count on Chesterton solutions toincrease equipment reliability, optimize energy consumption,and provide local technical support and service wherever they
are in the world.
Chesterton’s global capabilities include:
• Servicing plants in over 100 countries• Global manufacturing operations
• More than 500 Service Centers and Sales Offices worldwide• Over 1200 trained local Service Specialists and Technicians
Visit our website at www.chesterton.com