longitudinal sway brace fitting - ericolongitudinal lateral * all brace and service pipes shown, not...

Longitudinal

Lateral

* All Brace and Service Pipes

shown, not included

*(XX) = Finish Specifier

Sway Brace assemblies are intended to be installed in accordance withNFPA®-13 and the manufacturer's installation instructions.

The required type, number, and size of fasteners used for the structure attachment fitting shall be in accordance with NFPA-13.

Installation Anglefrom Vertical

TECHNICAL SUPPORT:www.erico.com CFS403_J

INSTRUCTION SHEET

1 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.

CSBSTUStandard Universal Sway Brace or Restraint Device Sway Brace Fitting

WARNING:ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at 1.www.erico.com and from your ERICO customer service representative. ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.2.All instructions must be completely followed to ensure proper and safe installation and performance. 3.Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property 4.damage, serious bodily injury and death. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 5.All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any 6.other purpose.

NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.

The customer is responsible for:a. Conformance to all governing codes.b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.c. Using appropriate industry standard hardware as noted above.

SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

Dyna-Flow is a registered trademark of Allied Tube and Conduit Corporation.EZ FLOW is a trademark of Northwest Pipe Company.FM is a registered certification mark of FM Approvals LLC, LTD.NFPA is a registered trademark of National Fire Protection Association, Inc.UL is a registered trademark of UL LLC.

CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.

1. UL Listed for use with Lightwall Service Pipe, Schedule 10, and Schedule 40 Service Pipe, for use with 1 to 2 NPS Schedule 40 brace pipe or 1/4" angle iron (except for 10-inch).*2. **2015 lbs. [8960 N] load rating when used with 1/4" angle iron.**3. Rating with 1/4" angle iron is identical to Schedule 40 brace pipe.

UL® Loads (Listed for Restraints) - Lateral**

Part Number Dyna-Flow® Service Pipe Sch 10 Service Pipe Sch 40 Service Pipe

CSBSTU0100(XX) N/A 655 lb (2,914 N) 655 lb (2,914 N)

CSBSTU0125(XX) 655 lb (2,914 N) 655 lb (2,914 N) 655 lb (2,914 N)

CSBSTU0150(XX) 655 lb (2,914 N) 655 lb (2,914 N) 655 lb (2,914 N)

UL Loads (Listed for Sway Braces)

Part NumberLateral* Longitudinal**

Dyna-Flow® Service Pipe

EZ FLOW™ Service Pipe

Sch 10 Service Pipe

Sch 40 Service Pipe

Dyna-Flow® Service Pipe

Mega-Flow Service Pipe

Sch 10 Service Pipe

Sch 40 Service Pipe

CSBSTU0200(XX) 3,000 lb (13,345 N) N/A 3,000 lb

(13,345 N)3,000 lb

(13,345 N) N/A N/A N/A N/A


(13,345 N)3,000 lb

(13,345 N)2,015 lb

(8,963 N) N/A 2,015 lb (8,963 N)

2,015 lb (8,963 N)


(13,345 N)3,000 lb

(13,345 N)2,015 lb

(8,963 N) N/A 2,015 lb (8,963 N)

2,015 lb (8,963 N)

CSBSTU0400(XX) 3,000 lb (13,345 N)

3,000 lb (13,345 N)

3,000 lb (13,345 N)

3,000 lb (13,345 N)

2,015 lb (8,963 N) N/A 2,015 lb

(8,963 N)2,015 lb

(8,963 N)

CSBSTU0500(XX) N/A 3,000 lb (13,345 N)

3,000 lb (13,345 N)

3,000 lb (13,345 N) N/A N/A 2,015 lb

(8,963 N)2,015 lb

(8,963 N)

CSBSTU0600(XX) N/A 3,000 lb (13,345 N)

3,000 lb (13,345 N)

3,000 lb (13,345 N) N/A 2,015 lb

(8,963 N)2,015 lb

(8,963 N)2,015 lb

(8,963 N)

CSBSTU0800(XX) N/A N/A 3,000 lb (13,345 N)

3,000 lb (13,345 N) N/A N/A 2,015 lb

(8,963 N)2,015 lb

(8,963 N)

CSBSTU1000(XX) N/A N/A 3,000 lb (13,345 N)

3,000 lb (13,345 N) N/A N/A 3,000 lb

(13,345 N)3,000 lb

(13,345 N)


INSTRUCTION SHEET




Notes:A) FM approved when used with 1", 1-1/4" or 2" (DN25, DN32, DN40, DN50) NPS Schedule 40, GB/T 3091, EN 10255 (Heavy), AS 1074 (Heavy) or JIS G3454 brace pipe.B) Load ratings for Schedule 40 above may also be applied to AS 1074 (Heavy), GB/T 3091, EN 10255 (Heavy) and JIS G3454 pipe.C) Load ratings for Schedule 40 above may also be applied to AS 1074 (Meduim), GB/T 3091, EN 10255 (Medium or Heavy), JIS G3452, FM approved Thinwall, and Schedule 40 pipes unless otherwise indicated.D) Load ratings for LW above refers to FM Approved Lightwall Pipe, commonly referred to as "Schedule 7". These ratings may also be applied to A1074 Lightwall, EN 10255 L, EN 10220, and GB/T 8163 pipe unless otherwise specified.E) Load ratings for "0.188 wall" above may be applied to any thicker walled pipe unless otherwise specified.


INSTRUCTION SHEET




Sway Braces are intended to be installed in accordance with NFPA®-13 and the manufacturer'sassembly and instructions.

CSBSTU is a Sway Brace Fitting. It is intended to be combined with a CADDY® brand Structural Attachment Fitting and "Bracing Pipe" to form a complete bracing assembly.

Position stamped components around service pipe Finger tighten nuts and rotate assembly to desiredorientation

Tighten top and bottom nuts to propertorque, reference torque chart.*(XX) Finish Specifier

Insert brace into clamp as far as possible.Tighten set screw until head snaps off

#1 #2

#3 #4


INSTRUCTION SHEET





INSTRUCTION SHEET




Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.



INSTRUCTION SHEET







INSTRUCTION SHEET




The CSBBARJ can be installedas shown on the top flange of an I-Beam with tapered or non-tapered flanges.

The CSBBARJ can be installedas shown on the top flange of an I-Beam with tapered or non-tapered flanges.


INSTRUCTION SHEET





INSTRUCTION SHEET




Through bolt shown.A lag screw may alsobe used.



INSTRUCTION SHEET







INSTRUCTION SHEET




longitudinal sway brace fitting - ericolongitudinal lateral * all brace and service pipes shown, not...

Documents