csbezu easy universal sway brace or restraint device · easy universal sway brace or restraint...
TRANSCRIPT
-
Longitudinal
Lateral
*(XX) = Finish Specifier.
Sway Brace assemblies are intended to be installed in accordance with NFPA®-13 and the manufacturer's installation instructions.
The required type, number, and size of fasteners used for the structure attachment fitting shall be in accordance with NFPA-13.
* All Brace and Service Pipes
shown, notincluded
Installation Anglefrom Vertical
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
1 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
WARNING:ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at 1.www.erico.com and from your ERICO customer service representative. ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.2.All instructions must be completely followed to ensure proper and safe installation and performance. 3.Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property 4.damage, serious bodily injury and death. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 5.All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any 6.other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:a. Conformance to all governing codes.b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
Dyna-Flow is a registered trademark of Allied Tube and Conduit Corporation.EZ FLOW is a trademark of Northwest Pipe Company.FM is a registered certification mark of FM Approvals LLC, LTD.NFPA is a registered trademark of National Fire Protection Association, Inc.UL is a registered trademark of UL LLC.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
-
1. UL Listed for use with Lightwall Service Pipe, Schedule 10, and Schedule 40 Service Pipe, for use with 1 to 2 NPS Schedule 40 brace pipe or 1/4" angle iron. *2. 2015 lbs. (8963 N) load rating when used with 1/4" angle iron.**3. Rating with 1/4" angle iron is identical to Schedule 40 brace pipe.
UL® Loads (Listed for Restraints) - Lateral**
Part Number Dyna-Flow® Service Pipe Sch 10 Service Pipe Sch 40 Service Pipe
CSBEZU0100(XX) N/A 655 lb (2,914 N) 655 lb (2,914 N)
CSBEZU0125(XX) 655 lb (2,914 N) 655 lb (2,914 N) 655 lb (2,914 N)
CSBEZU0150(XX) 655 lb (2,914 N) 655 lb (2,914 N) 655 lb (2,914 N)
UL Loads (Listed for Sway Braces)
Part NumberLateral* Longitudinal**
Dyna-Flow® Service Pipe
EZ FLOW™ Service Pipe
Sch 10 Service Pipe
Sch 40 Service Pipe
Dyna-Flow® Service Pipe
Mega-Flow Service Pipe
Sch 10 Service Pipe
Sch 40 Service Pipe
CSBEZU0200XX 3,000 lb (13,345 N) N/A3,000 lb
(13,345 N)3,000 lb
(13,345 N) N/A N/A N/A N/A
CSBEZU0250XX 3,000 lb (13,345 N) N/A3,000 lb
(13,345 N)3,000 lb
(13,345 N)1,265 lb
(5,627 N) N/A1,265 lb
(5,627 N)1,265 lb
(5,627 N)
CSBEZU0300XX 3,000 lb (13,345 N) N/A3,000 lb
(13,345 N)3,000 lb
(13,345 N)1,265 lb
(5,627 N) N/A1,265 lb
(5,627 N)1,265 lb
(5,627 N)
CSBEZU0400XX 3,000 lb (13,345 N)3,000 lb
(13,345 N)3,000 lb
(13,345 N)3,000 lb
(13,345 N)1,265 lb
(5,627 N) N/A1,265 lb
(5,627 N)1,265 lb
(5,627 N)
CSBEZU0500XX N/A 3,000 lb (13,345 N)3,000 lb
(13,345 N)3,000 lb
(13,345 N) N/A1,600 lb
(7,117 N)1,600 lb
(7,117 N)1,600 lb
(7,117 N)
CSBEZU0600XX N/A 3,000 lb (13,345 N)3,000 lb
(13,345 N)3,000 lb
(13,345 N) N/A1,600 lb
(7,117 N)1,600 lb
(7,117 N)1,600 lb
(7,117 N)
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
2 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Notes:A) FM approved when used with 1", 1-1/4", 1-1/2" or 2" (DN25, DN32, DN40, DN50) NPS Schedule 40, GBT/T 3091, EN 10255 (Heavy), AS 1074 (Heavy) or JIS G3454 brace pipe. B) Load ratings for Schedule 40 above may also be applied to AS 1074 (Heavy), GB/T 3091, EN 10255 (Heavy), and JIS G3454 pipe.C) Load ratings for Schedule 10 above may also be applied to AS 1074 (Medium), GB/T 3091, EN 10255 (Medium or Heavy), JIS G3452, FM approved thinwall, and Schedule 40 unless otherwise indicated. D) Load ratings for LW above refers to FM approved lightwall pipe, commonly referred to as "Schedule 7". These ratings may also be applied to AS 1074 Lightwall, EN 10255 L, EN 10220, and GB/T 8163 pipe unless otherwise specified.E) Load ratings for "0.188 wall" above may be applied to any thicker walled pipe unless otherwise specified.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
3 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
CSBEZU is a Sway Brace Fitting. It is intended to be combined with a CADDY® brand Structural Attachment Fitting and "Bracing Pipe" to form a complete bracing assembly.
Sway Braces are intended to be installed in accordance with NFPA®-13 and the manufacturer's assembly and instructions.
Rotate slotted stamped component over bolts.(Hardware does not have to be removed)*Slot should face away from brace pipe.
Finger tighten nuts and rotate assembly to desired orientation.
Tighten bolt that passes through CSBUNIV (brace clamp)to proper torque (reference torque chart) first, then proceed with other bolt.
Insert brace into clamp as far as possible.Tighten shear head set screw until head snaps off.
#1 #2
#3 #4
*(XX) Finish Specifier
* All Brace and Service Pipes shown, not included
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
4 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
5 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
6 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
7 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
8 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
9 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
10 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
11 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
The CSBBARJ can be installed asshown on the top flange of an I-Beam with tapered or non-tapered flanges.
The CSBBARJ can be installed asshown on the top flange of an I-Beam with tapered or non-tapered flanges.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
12 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
13 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
14 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
15 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Through bolt shown.A lag screw may alsobe used.
Through bolt shown.A lag screw may alsobe used.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
16 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
-
Through bolt shown.A lag screw may alsobe used.
Through bolt shown.A lag screw may alsobe used.
TECHNICAL SUPPORT:www.erico.com CFS386_H
INSTRUCTION SHEET
17 OF 17 © 2009, 2011, 2012, 2013, 2014 ERICO International Corporation.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CSBEZUEasy Universal Sway Brace or Restraint Device Sway Brace Fitting
Sheet1Drawing View4Drawing View5
Sheet2Sheet3Sheet4Sheet5Drawing View6Drawing View8Drawing View10Drawing View12
Sheet6Drawing View13Drawing View15Drawing View17Drawing View19
Sheet7Drawing View20Drawing View21Drawing View23
Sheet8Drawing View26Drawing View29Drawing View32
Sheet9Drawing View36Drawing View39Drawing View41
Sheet10Drawing View44Drawing View49Drawing View52
Sheet11Drawing View54Drawing View56Drawing View58Drawing View60
Sheet12Drawing View63Drawing View66
Sheet13Drawing View68Drawing View70Drawing View72Drawing View74
Sheet14Drawing View76Drawing View78Drawing View80Drawing View82
Sheet15Drawing View85Drawing View87
Sheet16Drawing View91Drawing View94Drawing View97Drawing View100
Sheet17Drawing View104Drawing View109Drawing View113Drawing View118