list of technical standard for water supply
TRANSCRIPT
1
EQUIPMENT, DEVICES, MATERIAL, SYSTEM OR FACILITY FOR WATER SUPPLY SYSTEM (list as of November 2010)
No. Category Items
1 A. Treatment of water A.1 Water Treatment Chemical
- Coagulant and flocculant
- Adsorption agents
- Fluoridation chemical
- Disinfectant
- Conditioning agent
- Other oxidation agent
A.2 Single treatment unit
- membrane filter
A.3 Complete small scale water treatment
2 B. Conveyance/distribution
of Water
B.1 Pipes with material:
- Polyethylene (PE)
- Polyvinylchloride (PVC)
- Acrylonitrile-butadiene-styrene
(ABS)
- Polypropylene (PP)
- Polybutelene (PB)
- Glass reinforced plastic (GRP)
- Mild Steel Cement Lined (MS)
- Stainless Steel (SS)
- Ductile Iron (DI)
- Copper tubes
- Composite pipes
B.2 Paip Fitting/ Joint/ Special
Joints
- Flanged joins
- Welded joints
- Gobout joints
- Flexible mechanical coupling
- Butt Fusion/electrifusion
- Sleeve coupling
- Push on spigot and socket
- Sinle gland-machanical joint
- Stepped coupling
Fittings and Special
- Tapers
- Flange adaptors
- Bends
- Tees
- Angle branches and Crosses
- Puddle Flanges
- Bellmouth
- Rose strainer
- Blank Flanges
2
No. Category Items
3. C. Storage of water (tank and
reservoir
C.1 Balancing and services reservoir
- Reinforce concrete
- Prestress concrete
- Precast concrete
- Glass Reinfirced Polyester
- Fiberglass RP
- Stainless steel
- Polyethelene
- Galvanized pressed steel
3 D. Other mechanical
equipment and installation
for water supply system
D.1 Pump
D.2 Valve
- Sluice valves/gate valves
- Check valves
- Scour valves
- Air valves/ air release valve
- Stoppable valves/ lockable
valves/servicing valves
- Control valve/automatic control
valve
- Butterfly valves
- Reflux valves
- Ball or Float valves
- Altitude valves
- Pressure reducing valves
- Pressure sustaining valves
- Constant flow valves
- Hydrants
- Free Discharge Valve
- In-Line Throttling Valve
- Submerged Discharge Valve
- Pressure Sustaining Valve
- Constant Flow Valve
- Backflow Preventer
D.3 Meter
- Bulk meters
- Sub meters
- Domestic meter
D.4 Others
(1) Air blower
(2) Air compressors
(3) Chemical dosing devices
(4) Surge suppression devices
(5) Instrumentation
(6) Hydraulic controlled equipment
(7) Bandscreen
3
No. Category Items
(8) Ejector
4. E. Water supply plumbing
system
(1) Taps
(2) Stop valves
(3) Ball valves
(4) Constant flow valves
(5) Flushing cisterns
(6) Bidets
(7) Drinking fountain
1
LIST OF TECHNICAL STANDARD FOR EQUIPMENT, DEVICE, MATERIAL, SYSTEM OR FACILITY FOR WATER SUPPLY SYSTEM
CATEGORY A: TREATMENT OF WATER
A.1 WATER TREATMENT CHEMICAL A.2 SINGLE TREATMENT UNIT A.3 COMPLETE SMALL SCALE WATER TREATMENT
PRODUCTS STANDARDS
Aluminium Sulphate (Kibble & Liquid Form)
MS 699:2008: Aluminium Sulphate for Use in Potable Water Supply –Specification (Second Revision)
Polyaluminium chloride hydroxide / Polyaluminium chloride hydroxide sulphate / Polyaluminium chloride hydroxide silicate sulphate
MS 1454:2007 Liquid polyaluminium chloride for use in potable water supply – specification (first revision), 2007
Sodium Aluminate
MS 1572:2003 Specification for Sodium Aluminate used for potable water supply
Iron (III) chloride Iron (III) chloride sulphate
MS 1450:1999: Specification for liquid ferric chloride for potable water treatment
Iron (II) sulphate Iron (III) sulphate liquid Iron (III) sulphate solid
MS 1452 – 1999 Specification for liquid ferric sulphate for potable water treatment
MS 1456:1999 : Guidelines for the application of liquid ferric based salts in potable water
2
PRODUCTS STANDARDS
Application of liquid ferric based product in potable water treatment
treatment
Product based on Polydiallyldimethyl ammonium chloride (PolyDADMAC) - Anionic, Cationic
MS 1930:2007 : Poly(polydiallyldimethyl ammonium chloride) or polyDADMAC for use in potable water supply
Product based on polyacrylamides - Anionic, Cationic and non-ionic
MS 1928:2007 : polyacrylamides for use in potable water supply (specification)
Product based on Polyamines - Anionic, Cationic
MS 1929: 2007 : polyamines for use in potable water supply (specification)
Calcium carbonate MS 1836:2005 Hydrated Lime and slurry lime for use in potable water supply
Sodium carbonate MS 1551 : 2002 Specification for soda ash (sodium carbonate) used for potable water supply
Chlorine MS 171:2003 – Specification for liquid chlorine used for potable water supply
Sodium hypochlorite MS 1718:2003 : sodium hypochlorite for use in potable water supply
Calcium hypochlorite MS 1548:2003 : specification for calcium hypochlorite use for potable water supply 2003
Sodium flouride MS 1573 : 2003 – Specification for sodium fluoride used for potable water supply
Sodium silicofloride MS 1724:2004 – Sodium silicofloride for use in potable water supply specification 2004
potassium permanganate
MS 1576: 2003 – specification for potassium permanganate used for potable water supply
Copper sulphate MS 1576:2003: Specification for Copper Sulphate used for potable water.
Activated carbon (powder) MS 873:2005 : powdered activated carbon for use in potable water supply – specification
Activated carbon (granular) Granular activated carbon for use in potable water supply (specification)
3
PRODUCTS STANDARDS
Silica sand MS 847: 1983 - specification for silica sand for the manufacturer of sodium silicate.
Sodium Hydroxide
MS 700: 1981 (Specification) for sodium hydroxide (technical grades)
CATEGORY B: CONVEYANCE OF WATER
B.1 PIPE B.2 PIPE FITTINGS/JOINT/SPECIAL
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
CATEGORY B – PRODUCTS USED FOR THE CONVEYANCE OF WATER.
B.1 Pipes
B.1.1 Polyethylene (PE) Pipes
B.1.1.1 Polyethylene (PE)
Pipes
MS 1058: Part 2: 2002
Specification for Polyethylene (PE) Piping Systems for Water Supply : Part 2 : Pipes (Third
Revision) MS 1058: Part 2:
2005
MS 1058: Part 2: 2005
Specification for Polyethylene (PE) Piping Systems for Water Supply : Part 2 : Pipes (Forth
Revision)
4
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
ISO 4427-2: 2007
Plastics Piping Systems – Polyethylene (PE) Pipes and
Fittings for Water Supply – Part 2: Pipes
B.1.1.2 PE-RT Pipes
ISO 22391: Part 2: 2007
Plastics Piping Systems for Hot and Cold Water Installations –
Polyethylene of Raised Temperature Resistance (PE-
RT) : Part 2 : Pipes ISO 22391: Part 2: 2007
MS ISO 10508:2004
Plastics Piping Systems for Hot and Cold Water Installations – Guidance for Classification and
Design
B.1.2 Polyvinyl Chloride (PVC) Pipes
B.1.2.1 Unplasticized
Polyvinylchloride (uPVC) Pipes
MS 628: Part 1: 1999 AMD.1: 2001 & AMD.2: 2002
Specification for Unplasticised PVC (uPVC) Pipes for Water
Supply : Part 1: Pipes (1st revision)
MS 628: Part 1: 1999 AMD.1: 2001
& AMD.2: 2002
MS 762: 2007, AMD.1: 2010
Plastics Piping Systems for Industrial Applications –
Unplasticised Polyvinyl Chloride (PVC-U) – Specifications for Components and the System
(First Revision)
5
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
BS 3505: 1986
Specification for Unplasticized Polyvinyl Chloride (PVC-U)
Pressure Pipes for Cold Potable Water.
BS 3506: 1969 Specification for Unplasticized PVC Pipes for Industrial Uses
BS EN ISO 1452-2: 2009
Plastics Piping Systems for Water Supply and for Buried and
Above-Ground Drainage and Sewerage Under Pressure.
Unplasticized Poly(vinyl Chloride) (PVC U). Pipes
B.1.2.2 Multi-Layer uPVC
Pipes
MS 628: Part 1: 1999 AMD.1: 2001 & AMD.2: 2002
Specification for Unplasticised PVC (uPVC) Pipes for Water
Supply : Part 1: Pipes (1st revision)
MS 628: Part 1: 1999 AMD.1: 2001
& AMD.2: 2002
B.1.2.3 Chlorinated
Polyvinylchloride (cPVC) Pipes
ASTM D2846 / D2846M – 09b
Standard Specification for Chlorinated Polyvinyl Chloride (cPVC) Plastic Hot and Cold Water Distribution System.
ASTM D2846 / D2846M – 09b
B.1.3 Acrylonitrile-Butadiene-Styrene (ABS) Pipes
6
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.1.3.1 Acrylonitrile-Butadiene-
Styrene (ABS) Pipes
MS 1419: Part 1: 2007
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for
Pressure Applications – Part 1: Specification for Compounds,
Pipes and Fittings (First Revision) MS 1419: Part 1:
2007 &
MS 1419: Part 2: 2007
MS 1419: Part 2:
2007
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for
Pressure Applications – Part 2: Methods of Test
AS/NZS 3518: 2004 Acrylonitrile Butadiene Styrene (ABS) Compounds, Pipes and
Fittings for Pressure Application
B.1.4 Polypropylene (PP) Pipes
B.1.4.1 Polypropylene Random
(PP-R) Pipes
ISO 15874: Part 2: 2003
Plastics Piping Systems for Hot and Cold Water Installations –
Polypropylene (PP). Part 2: Pipes ISO 15874: Part 2:
2003
DIN 8077: 2008 Polypropylene (PP) Pipes – PP-
H, PP-B, PP-R, PP-RCT - Dimensions
B.1.4.2 Polypropylene Blend
(PP-B) Pipes ISO 15874: Part 2:
2003
Plastics Piping Systems for Hot and Cold Water Installations –
Polypropylene (PP). Part 2: Pipes
ISO 15874: Part 2: 2003
7
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
DIN 8077: 2008 Polypropylene (PP) Pipes – PP-
H, PP-B, PP-R, PP-RCT - Dimensions
B.1.5 Polybutylene (PB) Pipes
B.1.5.1 Polybutylene (PB)
Pipes AS/NZS 2642-2:
1994
Polybutylene (PB) Plumbing Pipe Systems – Polybutylene (PB) Pipe for Hot and Cold
Water Applications.
AS/NZS 2642-2: 1994
B.1.6 Glass Reinforced Plastic (GRP) Pipes
B.1.6.1 Glass Reinforced
Plastic (GRP) Pipes ISO 10639: 2004
Plastics Piping System for Pressure and Non-pressure
Water Supply – Glass Reinforced Thermosetting
Plastics (GRP) Systems Based On Unsaturated Polyester (UP)
Resin
ISO 10639: 2004
B.1.7 Mild Steel Cement Lined (MS) Pipes
B.1.7.1 Mild Steel Cement Lined (MS) Pipes –
BS 534: 1990 Steel Pipes, Joints and Specials
for Water and Sewage BS 534: 1990
8
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
ERW & SAW
BS 3601: 1987
Carbon Steel Pipes and Tubes with Specified Room
Temperature Properties for Pressure Purposes
B.1.7.2 Mild Steel Pipes (Bare tubes) – ERW & SAW
MS 1968: 2007 (BS EN 10224: 2002)
Non-alloy steel tubes and fittings for the conveyance of aqueous
liquids including water for human consumption – Technical
delivery conditions. MS 1968: 2007 (BS EN 10224:
2002)
BS 3601: 1987
Carbon Steel Pipes and Tubes with Specified Room
Temperature Properties for Pressure Purposes
B.1.8 Stainless Steel (SS) Pipes
B.1.8.1 Stainless Steel (SS)
Pipes - Industrial MS 1841: 2010 (ASTM A 312)
Seamless, Welded and Heavily Cold Austenitic Stainless Steel
Pipes - Specification
MS 1841: 2010 (ASTM A 312)
B.1.8.2 Stainless Steel (SS) Light Gauge Tubes -
MS 1988: 2007 (BS EN 10312)
Welded Stainless Steel Tubes for the Conveyance of Water and Other Aqueous Liquids – Technical Delivery Conditions
JIS G 3448: 2004 Light Gauge Stainless Steel
Pipes for Ordinary Piping
B.1.9 Ductile Iron (DI) Pipes
9
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.1.9.1 Ductile Iron (DI) Pipes
BS EN 545: 2006
Ductile Iron Pipes, Fittings, Accessories and Their Joints for Water Pipelines – Requirement
and Test Method MS 1919: 2006 (BS EN 545: 2002)
MS 1919: 2006 (BS EN 545: 2002)
Ductile Iron Pipes, Fittings, Accessories and Their Joints for Water Pipelines – Requirement
and Test Method
B.1.10 Copper Tubes
B.1.10.1 Copper Tubes BS EN 1057: 1996
Copper and Copper Alloys. Seamless, Round Copper
Tubes for Water and Gas in Sanitary and Heating
Applications
BS EN 1057: 1996
B.1.11 Composite Pipes
B.1.11.1 PE Aluminium Pipes ASTM F1282 - 03
Standard Specification for Polyethylene / Aluminium / Polyethylene (PE-AL-PE)
Composite Pressure Pipes
ASTM F1282 - 03
B.1.11.2 Polysteel Pipes CJ/T 136: 2001 Steel Pipes of Lining Plastic for
Water Supply CJ/T 136: 2001
This standard is in Chinese Language. There is no
english version available.
10
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2 Pipe Fittings
B.2.1 Polyethylene (PE) Fittings
B.2.1.1
Polyethylene (PE) Fittings
BS EN 12201-3:2003 Polyethylene Pipes for Water
Supply. Part 3 : Fittings
MS 1058: Part 3: 2006
AS/NZS 4129: 2008 Fittings for Polyethylene (PE) Pipes for Pressure Application
MS 1058: Part 3: 2006
Polyethylene (PE) Piping Systems for Water Supply – Part
3 : Fittings
ISO 4427-3: 2007
Plastics Piping Systems – Polyethylene (PE) Pipes and
Fittings for Water Supply – Part 3: Fittings
B.2.1.2
HDPE Joints Assemblies and
Fittings for HDPE Pipes
DIN 16963: Part 4: 1988
Pipe Joint Assemblies and Fittings for High-Density
Polyethylene (PE-HD) Pressure Pipes; Adaptors for Fusion
Jointing, Flanges and Sealing Elements; Dimensions
DIN 16963: Part 4: 1988,
DIN 16963: Part 5: 1989 &
DIN 16963: Part 6: 1989
11
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
DIN 16963: Part 5: 1989
Pipe Joints and Components of Polyethylene (PE) for Pipes
Under Pressure, PE 80 and PE 100 – Part 5: General Quality
Requirements, Testing
DIN 16963: Part 6: 1989
Pipe Joints Assemblies and Fittings for High-Density
Polyethylene (PE-HD) Pressure Pipes; Injection-Moulded Fittings
for Butt Welding: Dimensions
B.2.1.3
PE Socket Fusion Fittings
DIN 16963: Part 5: 1989
Pipe Joints and Components of Polyethylene (PE) for Pipes
Under Pressure, PE 80 and PE 100 – Part 5: General Quality
Requirements, Testing DIN 16963: Part 5: 1989,
DIN 16963: Part 8: 1980,
DIN 16963: Part 9: 1980,
DIN 16963: Part 10: 1980 &
DIN 16963: Part 14: 1983
DIN 16963: Part 8:
1980
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Injection
Moulded Elbows for Socket-Welding, Dimensions
DIN 16963: Part 9: 1980
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Injection
Moulded Tee Pieces for Socket-Welding, Dimensions
12
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
DIN 16963: Part 10: 1980
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Injection
Moulded Sockets and Caps for Socket-Welding, Dimensions
DIN 16963: Part 14: 1983
Pipe Joint Assemblies and Fittings for High-Density
Polyethylene (HDPE) Pressure Pipes; Pipe Couplings;
Dimensions
B.2.1.4
PE Fabricated Fittings
DIN 16963: Part 1: 1980
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Pipe Bends of
Segmental Construction for Butt-Welding, Dimensions
DIN 16963: Part 1: 1980,
DIN 16963: Part 2: 1983 &
DIN 16963: Part 5: 1999
DIN 16963: Part 2: 1983
Pipe Joint Assemblies and Fittings for Types 1 and 2 High Density Polyethylene (HDPE)
Pressure Pipes; Tees and Branches Produced by Segment
Inserts and Necking for Butt Welding; Dimensions
13
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
DIN 16963: Part 5: 1999
Pipe Joints and Components of Polyethylene (PE) for Pipes
Under Pressure, PE 80 and PE 100 – Part 5: General Quality
Requirements, Testing
B.2.1.5
Nylon Joints and Compression Fittings for Use with HDPE
Pipes
BS 5114: 1975 (1981) Amd.2 - 1987
Specification for Performance Requirements for Joints and Compression Fittings for Use
with Polyethylene Pipes BS 5114: 1975 (1981) Amd.2 -
1987
MS ISO 10508: 2009
Plastics Piping Systems for Hot and Cold Water Installations – Guidance for Classification and
Design
B.2.2 Unplasticized Polyvinyl Chloride (PVC) Fittings
B.2.2.1
Unplasticized Polyvinylchloride (uPVC) Fittings
MS 628: Part 2: Section 2.1: 1999
Specification for Unplasticised PVC (uPVC) Pipes for Water Supply : Part 2: Joints and Fittings for Use with uPVC
Pipes: Section 2.1: uPVC Joints and Fittings
MS 628: Part 2: Section 2.1: 1999
14
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
BS EN ISO: 1452-3: 2009
Plastics Piping Systems for Water Supply and for Buried and
Above-Ground Drainage and Sewerage Under Pressure.
Unplasticized Poly(vinyl Chloride) (PVC U). Fittings.
BS 4346-1: 1969
Joints and Fittings for use with Unplasticized PVC Pressure
Pipes. Injection Moulded Unplasticized PVC Fittings for Solvent Welding for use with
Pressure Pipes, Including Potable Water Supply.
BS 4346-2: 1970
Joints and Fittings for use with Unplastisized PVC Pressure
Pipes. Mechanical Joints and Fittings, Principally of Unplasticized PVC.
B.2.2.2
Chlorinated
Polyvinylchloride (cPVC) Fittings
ASTM D2846 / D2846M – 09b
Standard Specification for Chlorinated Polyvinyl Chloride (cPVC) Plastic Hot and Cold Water Distribution System.
ASTM D2846 / D2846M – 09b
15
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.3 Acrylonitrile-Butadiene-Styrene (ABS) Fittings
B.2.3.1
Acrylonitrile-Butadiene-Styrene (ABS) Fittings
MS 1419: Part 2: 1997
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for
Pressure Applications – Part 2: Methods of Test
MS 1419: Part 2: 1997 &
MS 1419: Part 1: 2007
MS 1419: Part 1: 2007
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for
Pressure Applications – Part 1: Specification for Compounds,
Pipes and Fittings (First Revision)
AS/NZS 3518: 2004 Acrylonitrile Butadiene Styrene (ABS) Compounds, Pipes and
Fittings for Pressure Application
B.2.4 Polypropylene (PP) Fittings
B.2.4.1
Polypropylene (PP-R, PP-B & PP-H) Fittings
ISO 15874: Part 3: 2003
Plastics Piping Systems for Hot and Cold Water Installations – Polypropylene (PP) – Part 3 :
Fittings
ISO 15874: Part 3: 2003
16
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
DIN 16962-5: 2000
Pipe Joints and Elements for Polypropylene (PP) for Pipes
Under Pressure, PP-H 100, PP-B 80 and PP-R 80 – Part 5:
General Quality Requirements, Testing.
B.2.4.2
Polypropylene (PP) Compression Fittings
for HDPE Pipes
BS 5114: 1975 (1981) Amd.2 - 1987
Specification for Performance Requirements for Joints and Compression Fittings for Use
with Polyethylene Pipes
BS 5114: 1975 (1981) Amd.2 -
1987
ISO 3458: 1976
Assembled Joints Between Fittings and Polyethylene (PE)
Pressure Pipes Test of Leakproofness Under Internal
Pressure.
ISO 3459: 1976
Polyethylene (PE) Pressure Pipes – Joints Assembled with
Mechanical Fittings Internal Under-Pressure Test Method
and Requirement.
ISO 3503: 1976
Assembled Joints Between Fittings and Polyethylene (PE)
Pressure Pipes – Test of Leakproofness Under Internal Pressure when Subjected to
Bending.
17
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
ISO 3501: 1976
Assembled Joints Between Fittings and Polyethylene (PE)
Pressure Pipes – Test of Resistance to Pull Out.
ISO 14236: 2000
Plastics Pipes and Fittings – Mechanical-Joint Compression
Fittings for Use with Polyethylene Pressure Pipes in
Water Supply Systems.
B.2.5 Glass Reinforced Plastic (GRP) Fittings
B.2.5.1
Glass Reinforced Plastic (GRP) Fittings
ISO 10639: 2004
Plastics Piping System for Pressure and Non-pressure
Water Supply – Glass Reinforced Thermosetting
Plastics (GRP) Systems Based On Unsaturated Polyester (UP)
Resin
ISO 10639: 2004
B.2.6 Mild Steel (MS) Cement Lined Fittings
B.2.6.1
Mild Steel (MS) Cement Lined
Specials (ERW & SAW)
BS 534: 1990 Steel Pipes, Joints and Specials
for Water and Sewage
BS 534: 1990
MS 1968: 2007
Non-alloy steel tubes and fittings for the conveyance of aqueous
liquids including water for human consumption – Technical
delivery conditions.
18
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.7 Stainless Steel (SS) Fittings
B.2.7.1
Stainless Steel (SS) Threaded Fittings
ISO 4144: 2003 Pipework – Stainless Steel
Fittings Threaded in Accordance with ISO 7-1.
ISO 4144: 2003
B.2.7.2
Stainless Steel (SS) Welded Fittings
MS 1842: 2010 (ASTM A 403)
Wrought Austenitic Stainless Steel Piping Fittings –
Specification (First Revision).
MS 1842: 2010 (ASTM A 403)
B.2.7.3
Stainless Steel (SS) Press Fittings
SAS 322: 2003 Stainless Steel Press Fittings SAS 322: 2003
This standard is in Japanese Language.
There is no english version available.
B.2.8 Ductile Iron (DI) Fittings
B.2.15 Ductile Iron (DI)
Fittings MS 1919: 2006
(BS EN 545: 2002)
Ductile Iron Pipes, Fittings, Accessories and Their Joints for Water Pipelines – Requirement
and Test Method
MS 1919: 2006 (BS EN 545: 2002)
B.2.9 Copper Fittings
B.2.9.1
Copper Fittings (Short Ends & Capillary)
BS EN 1254-1: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings with Short Ends for Capillary Brazing
to Copper Tubes.
BS EN 1254-1: 1998
B.2.9.2
Copper Fittings (Compression Ends)
BS EN 1254-2: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings with Compression Ends for Use with
Copper Tubes.
BS EN 1254-2: 1998
19
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.9.3
Copper Fittings (Combining End)
BS EN 1254-4: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings
Combining Other End Connections with Capillary or
Compression Ends.
BS EN 1254-4: 1998
B.2.10 Composite Fittings
B.2.10.1 Polysteel Fittings CJ/T 137: 2001 Malleable Iron Threaded Fittings
of Lining Plastic for Water Supply.
CJ/T 137: 2001 This standard is in Chinese
Language. There is no english version available.
B.2.10.2 Polyphenol Oxidase
(PPO) Fittings AS 4176: 1994
Polyethylene / Aluminium and Cross-linked Polyethylene /
Aluminium Macro-Composite Pipe Systems for Pressure
Applications.
AS 4176: 1994
This is only the nearest standard available.
Standard specific for this product is not available.
B.2.11 Adapter
B.2.11.1 Variable Adapter Spesifikasi JKR 20200-0045-99
JKR Standard Specification for Detachable Joints and Variable Adaptors for uPVC, Ductile Iron
and AC Pipes.
Spesifikasi JKR 20200-0045-99
B.2.11.2 Flange Adapter Spesifikasi JKR 20200-0048-99
JKR Standard Specification For Flexible Couplings and Flange
Adaptors.
Spesifikasi JKR 20200-0048-99
20
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.11.3 Flexible Coupling Spesifikasi JKR 20200-0048-99
JKR Standard Specification For Flexible Couplings and Flange
Adaptors.
Spesifikasi JKR 20200-0048-99
B.2.11.4 Detachable Joint Spesifikasi JKR 20200-0045-99
JKR Standard Specification for Detachable Joints and Variable Adaptors for uPVC, Ductile Iron
and AC Pipes.
Spesifikasi JKR 20200-0045-99
B.2.12 Saddle
B.2.12.1 Ferrous Saddle Spesifikasi JKR 20200-0044-99
JKR Standard Specification for Ferrous Saddles.
Spesifikasi JKR 20200-0044-99
B.2.12.2 2 in 1 Adjustable
Saddle
Spesifikasi JKR 20200-0044-99 CL.
17.10
JKR Standard Specification for Ferrous Saddles.
Spesifikasi JKR 20200-0044-99
CL. 17.10
B.2.12.3 PP Clamp Saddle JKR No. 1 – 95 (BA)
JKR Standard Specification for Polypropylene (PP) Clamp
Saddle to be Used with Polyethylene (PE) Pipes.
JKR No. 1 – 95 (BA)
B.2.13 Pillar Hydrant
B.2.13.1 Pillar Hydrant Spesifikasi JKR 20200-0042-99
JKR Standard Specification for Ductile Iron Pillar Hydrants.
Spesifikasi JKR 20200-0042-99
21
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
MS 1395: 1996 Specification for Pillar Hydrants MS 1395: 1996
This MS Adopted the JKR No. 1 – 93 (BA) – JKR Specification for Pillar
Hydrants.
B.2.14 Strainer
B.2.14.1 Ductile Iron (DI)
Strainer Spesifikasi JKR 20200-0100-01
JKR Standard Specification for Ductile Iron Strainer (DN 50 to
DN 600)
Spesifikasi JKR 20200-0100-01
B.2.15 Ferrules
B.2.15.1 Swivel Ferrules Spesifikasi JKR 20200-0174-04
JKR Standard Specification for Ferrules
B.2.15.2 Under Pressure Vertical Ferrules
MS 1396: 2006 Ferrules – Specification (First
Revision)
B.2.1.4 PE Fabricated Fittings DIN 16963: Part 1:
1980
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Pipe Bends of
Segmental Construction for Butt-Welding, Dimensions
DIN 16963: Part 1: 1980,
DIN 16963: Part 2: 1983 &
DIN 16963: Part 5: 1999
22
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
DIN 16963: Part 2: 1983
Pipe Joint Assemblies and Fittings for Types 1 and 2 High Density Polyethylene (HDPE)
Pressure Pipes; Tees and Branches Produced by Segment
Inserts and Necking for Butt Welding; Dimensions
DIN 16963: Part 5: 1999
Pipe Joints and Components of Polyethylene (PE) for Pipes
Under Pressure, PE 80 and PE 100 – Part 5: General Quality
Requirements, Testing
B.2.1.5
Nylon Joints and Compression Fittings for Use with HDPE
Pipes
BS 5114: 1975 (1981) Amd.2 - 1987
Specification for Performance Requirements for Joints and Compression Fittings for Use
with Polyethylene Pipes
BS 5114: 1975 (1981) Amd.2 -
1987
MS ISO 10508: 2009
Plastics Piping Systems for Hot and Cold Water Installations – Guidance for Classification and
Design
23
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.2 Unplasticized Polyvinyl Chloride (PVC) Fittings
B.2.2.1
Unplasticized Polyvinylchloride (uPVC) Fittings
MS 628: Part 2: Section 2.1: 1999
Specification for Unplasticised PVC (uPVC) Pipes for Water Supply : Part 2: Joints and Fittings for Use with uPVC
Pipes: Section 2.1: uPVC Joints and Fittings
MS 628: Part 2: Section 2.1: 1999
BS EN ISO: 1452-3: 2009
Plastics Piping Systems for Water Supply and for Buried and
Above-Ground Drainage and Sewerage Under Pressure.
Unplasticized Poly(vinyl Chloride) (PVC U). Fittings.
BS 4346-1: 1969
Joints and Fittings for use with Unplasticized PVC Pressure
Pipes. Injection Moulded Unplasticized PVC Fittings for Solvent Welding for use with
Pressure Pipes, Including Potable Water Supply.
BS 4346-2: 1970
Joints and Fittings for use with Unplastisized PVC Pressure
Pipes. Mechanical Joints and Fittings, Principally of Unplasticized PVC.
24
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.2.2
Chlorinated Polyvinylchloride (cPVC) Fittings
ASTM D2846 / D2846M – 09b
Standard Specification for Chlorinated Polyvinyl Chloride (cPVC) Plastic Hot and Cold Water Distribution System.
ASTM D2846 / D2846M – 09b
B.2.3 Acrylonitrile-Butadiene-Styrene (ABS) Fittings
B.2.3.1
Acrylonitrile-Butadiene-Styrene (ABS) Fittings
MS 1419: Part 2: 1997
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for
Pressure Applications – Part 2: Methods of Test
MS 1419: Part 2: 1997 &
MS 1419: Part 1: 2007
MS 1419: Part 1: 2007
Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for
Pressure Applications – Part 1: Specification for Compounds,
Pipes and Fittings (First Revision)
AS/NZS 3518: 2004 Acrylonitrile Butadiene Styrene (ABS) Compounds, Pipes and
Fittings for Pressure Application
B.2.4 Polypropylene (PP) Fittings
B.2.4.1
Polypropylene (PP-R, PP-B & PP-H) Fittings
ISO 15874: Part 3: 2003
Plastics Piping Systems for Hot and Cold Water Installations – Polypropylene (PP) – Part 3 :
Fittings
ISO 15874: Part 3: 2003
25
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
DIN 16962-5: 2000
Pipe Joints and Elements for Polypropylene (PP) for Pipes
Under Pressure, PP-H 100, PP-B 80 and PP-R 80 – Part 5:
General Quality Requirements, Testing.
B.2.4.2
Polypropylene (PP) Compression Fittings
for HDPE Pipes
BS 5114: 1975 (1981) Amd.2 - 1987
Specification for Performance Requirements for Joints and Compression Fittings for Use
with Polyethylene Pipes
BS 5114: 1975 (1981) Amd.2 -
1987
ISO 3458: 1976
Assembled Joints Between Fittings and Polyethylene (PE)
Pressure Pipes Test of Leakproofness Under Internal
Pressure.
ISO 3459: 1976
Polyethylene (PE) Pressure Pipes – Joints Assembled with
Mechanical Fittings Internal Under-Pressure Test Method
and Requirement.
ISO 3503: 1976
Assembled Joints Between Fittings and Polyethylene (PE)
Pressure Pipes – Test of Leakproofness Under Internal Pressure when Subjected to
Bending.
26
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
ISO 3501: 1976
Assembled Joints Between Fittings and Polyethylene (PE)
Pressure Pipes – Test of Resistance to Pull Out.
ISO 14236: 2000
Plastics Pipes and Fittings – Mechanical-Joint Compression
Fittings for Use with Polyethylene Pressure Pipes in
Water Supply Systems.
B.2.5 Glass Reinforced Plastic (GRP) Fittings
B.2.5.1
Glass Reinforced Plastic (GRP) Fittings
ISO 10639: 2004
Plastics Piping System for Pressure and Non-pressure
Water Supply – Glass Reinforced Thermosetting
Plastics (GRP) Systems Based On Unsaturated Polyester (UP)
Resin
ISO 10639: 2004
B.2.6 Mild Steel (MS) Cement Lined Fittings
B.2.6.1
Mild Steel (MS) Cement Lined Specials
(ERW & SAW)
BS 534: 1990 Steel Pipes, Joints and Specials
for Water and Sewage
BS 534: 1990
MS 1968: 2007
Non-alloy steel tubes and fittings for the conveyance of aqueous
liquids including water for human consumption – Technical
delivery conditions.
27
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.7 Stainless Steel (SS) Fittings
B.2.7.1
Stainless Steel (SS) Threaded Fittings
ISO 4144: 2003 Pipework – Stainless Steel
Fittings Threaded in Accordance with ISO 7-1.
ISO 4144: 2003
B.2.7.2
Stainless Steel (SS) Welded Fittings
MS 1842: 2010 (ASTM A 403)
Wrought Austenitic Stainless Steel Piping Fittings –
Specification (First Revision).
MS 1842: 2010 (ASTM A 403)
B.2.7.3
Stainless Steel (SS) Press Fittings
SAS 322: 2003 Stainless Steel Press Fittings SAS 322: 2003
This standard is in Japanese Language.
There is no english version available.
B.2.8 Ductile Iron (DI) Fittings
B.2.15 Ductile Iron (DI)
Fittings MS 1919: 2006
(BS EN 545: 2002)
Ductile Iron Pipes, Fittings, Accessories and Their Joints for Water Pipelines – Requirement
and Test Method
MS 1919: 2006 (BS EN 545: 2002)
B.2.9 Copper Fittings
B.2.9.1 Copper Fittings (Short
Ends & Capillary) BS EN 1254-1: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings with Short Ends for Capillary Brazing
to Copper Tubes.
BS EN 1254-1: 1998
B.2.9.2 Copper Fittings
(Compression Ends) BS EN 1254-2: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings with Compression Ends for Use with
Copper Tubes.
BS EN 1254-2: 1998
28
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.9.3 Copper Fittings
(Combining End) BS EN 1254-4: 1998
Copper and Copper Alloys. Plumbing Fittings. Fittings
Combining Other End Connections with Capillary or
Compression Ends.
BS EN 1254-4: 1998
B.2.10 Composite Fittings
B.2.10.1 Polysteel Fittings CJ/T 137: 2001 Malleable Iron Threaded Fittings
of Lining Plastic for Water Supply.
CJ/T 137: 2001 This standard is in Chinese
Language. There is no english version available.
B.2.10.2 Polyphenol Oxidase
(PPO) Fittings AS 4176: 1994
Polyethylene / Aluminium and Cross-linked Polyethylene /
Aluminium Macro-Composite Pipe Systems for Pressure
Applications.
AS 4176: 1994
This is only the nearest standard available.
Standard specific for this product is not available.
B.2.11 Adapter
B.2.11.1 Variable Adapter Spesifikasi JKR 20200-0045-99
JKR Standard Specification for Detachable Joints and Variable Adaptors for uPVC, Ductile Iron
and AC Pipes.
Spesifikasi JKR 20200-0045-99
B.2.11.2 Flange Adapter Spesifikasi JKR 20200-0048-99
JKR Standard Specification For Flexible Couplings and Flange
Adaptors.
Spesifikasi JKR 20200-0048-99
29
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
B.2.11.3 Flexible Coupling Spesifikasi JKR 20200-0048-99
JKR Standard Specification For Flexible Couplings and Flange
Adaptors.
Spesifikasi JKR 20200-0048-99
B.2.11.4 Detachable Joint Spesifikasi JKR 20200-0045-99
JKR Standard Specification for Detachable Joints and Variable Adaptors for uPVC, Ductile Iron
and AC Pipes.
Spesifikasi JKR 20200-0045-99
B.2.12 Saddle
B.2.12.1 Ferrous Saddle Spesifikasi JKR 20200-0044-99
JKR Standard Specification for Ferrous Saddles.
Spesifikasi JKR 20200-0044-99
B.2.12.2 2 in 1 Adjustable
Saddle
Spesifikasi JKR 20200-0044-99 CL.
17.10
JKR Standard Specification for Ferrous Saddles.
Spesifikasi JKR 20200-0044-99
CL. 17.10
B.2.12.3 PP Clamp Saddle JKR No. 1 – 95 (BA)
JKR Standard Specification for Polypropylene (PP) Clamp
Saddle to be Used with Polyethylene (PE) Pipes.
JKR No. 1 – 95 (BA)
B.2.13 Pillar Hydrant
B.2.13.1 Pillar Hydrant Spesifikasi JKR 20200-0042-99
JKR Standard Specification for Ductile Iron Pillar Hydrants.
Spesifikasi JKR 20200-0042-99
30
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
MS 1395: 1996 Specification for Pillar Hydrants MS 1395: 1996
This MS Adopted the JKR No. 1 – 93 (BA) – JKR Specification for Pillar
Hydrants.
B.2.14 Strainer
B.2.14.1 Ductile Iron (DI)
Strainer Spesifikasi JKR 20200-0100-01
JKR Standard Specification for Ductile Iron Strainer (DN 50 to
DN 600)
Spesifikasi JKR 20200-0100-01
B.2.15 Ferrules
B.2.15.1 Swivel Ferrules Spesifikasi JKR 20200-0174-04
JKR Standard Specification for Ferrules
B.2.15.2 Under Pressure Vertical Ferrules
MS 1396: 2006 Ferrules – Specification (First
Revision)
31
CATEGORY C: STORAGE OF WATER (TANK AND RESERVOIR)
C.1 TANK
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
CATEGORY C – PRODUCT FOR STORAGE OF WATER
C.1 TANKS
C.1.1 Reinforced Concrete Reservoir / Tank
C.1.1.1 Precast Concrete Tank
C.1.2 Steel Tank
C.1.2.1
Glass Coated / Glass Lined / Glass Fused / Epoxy Coated / Epoxy
Lining
AWWA D103-97 ANSI/AWWA D103-
09
Factory-Coated Bolted Steel Tanks For Water Storage
No copy of the standard
C.1.2.2
Corrugated Steel Panel With
Polyethylene-Lined Water Storage Tank
BS 1449:Pt 1: 1991
Steel Plate, Sheet & Strip. Carbon and carbon-
manganese, sheet and strip.
BS 1449-1.1:1991, BS 1449-1.8:1991 & BS 1449-1.14:1991
SS 245:1995 (Cl. 10.2.1 & Cl 10.2.2)
Specification for Glass Reinforced Polyester Sectional
Water Tank
Cl 10.2.1 – Leakage Test Cl 10.2.2 – Deflection Test
C.1.2.3 Cylindrical Double
Fold System BS 5950-1:2000
Structural Use of Steelwork in Building Part 1 : Code of
Practice for Design – Rolled and Welded Section.
32
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
C.1.3 GRP / FRP Tanks
C.1.3.1 GRP / FRP Sectional
Water Tank
SS 245 : 1995 Specification for Glass
Reinforced Polyester Sectional Water Tank
BS EN 13280: 2001
Specification for glass fibre reinforced cistern of one-piece and sectional construction for storage above ground of cold
water
MS 1390 : 2010 Glass Reinforced Polyester Panels And Panels Water
Tanks
C.1.3.2 FRP One-Piece Water
Tank
BS 7491: Pt 2 : 1992
Glass Fibre Reinforced Plastic Cisterns for Cold Water
Storage. Specification for one piece cisterns of nominal
capacity for 500L to 25000L.
Superceded and replaced by BS EN 13280 : 2001
BS EN 13280: 2001
Specification for glass fibre reinforced cistern of one-piece and sectional construction for storage above ground of cold
water
JIS A 4110 : 1989 / Amendment 1 : 2008
Glass Fibre Reinforced Plastic Water Tanks (Amendment 1)
33
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
C.1.3.3 Fibreglass Water Tank MS 1241:1991 Specification for Fibreglass
Water Tanks – Effective Capacity of Less Than 2000L
C.1.4 Stainless Steel Water Tank
C.1.4.1 Stainless Steel Storage Tank
JKR 20200-0041-99 Stainless Steel Water Tanks
(With Effective Capacity Up to 15,000L)
CNS 9443 : 1989 Stainless Steel Storage Tanks For Rectangular / Panel
Tank
C.1.5 Polyethylene (PE) Water Tank
C.1.5.1 PE/HDPE Storage
Tank
MS 1225: Pt 1: 2007
Polyethylene (PE) Tanks For Cold Water Storage; Part 1:
Capacity up to 600G (Second Revision)
MS 1225: Pt 2: 2006
Polyethylene (PE) Tanks For Cold Water Storage; Part 2:
Capacity more than 600G (First Revision)
C.1.6 Pressed Steel Water Tank
C.1.6.1 Pressed Steel
Sectional Rectangular Tank Panel
BS 1564:1975 Specification for Pressed Steel Sectional Rectangular Tanks
C.1.6.2 Composite Stainless
Steel Tanks BS 1564:1975
Specification for Pressed Steel Sectional Rectangular Tanks
34
CATEGORY D: OTHER MECHANICAL EQUIPMENT AND INSTALLATION D.1 PUMP (BELUM ADA) D.2 VALVE D.3 METER
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
CATEGORY D – OTHER WATERWORKS MECHANICAL EQUIPMENT AND INSTALLATION
D.2 VALVES
D.2.1 Butterfly Valve BS EN 593 : 2004
Industrial Valves. Metallic Butterfly Valve
JKR 20200-0050-99* Butterfly Valves
D.2.2 Gate Valve / Sluice
Valve
BS 5163 : 1986
Specification for Predominantly Key-Operated Cast Iron Gate
Valve For Waterworks Purposes
BS 5150 : 1990 Specification for Cast Iron Gate
Valve
Superceded & replaced by BS EN 1171
BS EN 1171 : 2002 Industrial Valves. Cast Iron
Gate Valves
JKR 20200-0077-00 Ductile Iron Type B Large
Sluice Valves (DN700 to DN 1800)
D.2.3 Air Valve / Air Release
Valve
JKR 20200-0043-99 Ductile Iron Air Valves (Revised
Edition 1999)
JKR 20200-0097-01 Ductile Iron Air Valves (Revised
Edition 2001)
35
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
ANSI / AWWA C512-2004
Air Release, Air Vacuum, And Combination Air Valve for
Waterworks Service.
D.2.4 Check Valve
BS EN 12334 : 2001 Industrial Valves. Cast Iron
Check Valve
BS 5153 : 1974 Specification for Cast Iron Check Valves for General
Purposes.
Superceded & Replaced by BS EN 12334:2001
TS EN 12334:2001 Industrial Valves. Cast Iron
Check Valve
D.2.5 Scour Valve - No registration yet & no
standard available for this product
D.2.6 Stopvalve BS 5412 : 1996
Specification for Low Resistance Single Taps and Combination Tap Assemblies
(Nominal Size ½ and ¾) Suitable for Operation at PN 10 max. and a min. flow pressure
of 0.01MPa (0.1 bar)
D.2.7 Lockable Valve / Servicing Valve
BS EN 1213 : 2000
Building Valves. Copper Alloy Stopvalves for Potable Water Supply in Buildings. Test &
Requirement.
36
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
BS 6675 : 1986 Specification for Servicing
Valve (Copper Alloy) for Water Services
D.2.8 Float Operated Valve JKR 20200-0059-99* Piston Type Float Operated
Valves (Revised Edition 1999) No registration yet
D.2.9 Control Valve /
Automatic Control Valve
JKR 20200-0114-01* Ductile Iron Automatic Control
Valves for Waterworks Purposes (DN15-DN1000)
D.2.9.1 Pressure Reducing
Valve -
D.2.9.2 Altitude Valve -
D.2.9.3 Free Discharge Valve -
D.2.9.4 In-Line Throttling Valve -
D.2.9.5 Submerged Discharge
Valve -
D.2.9.6 Pressure Sustaining
Valve -
D.2.9.7 Constant Flow Valve -
D.2.9.8 Reflux Valve -
37
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
D.2.9.9 Backflow Preventer - No registration yet
Note : For Item D.2.9 up to D.2.9.8 – The product had been registered with us but without a standard. Lately we had been informed by IKRAM about there is a standard for control valve which is JKR Spec.
38
No. Product Standards referred by industry Standard for
SPAN registration Remarks
Standard No. Standard Title
CATEGORY D – OTHER WATERWORKS MECHANICAL EQUIPMENT AND INSTALLATION
D.3 WATER METER
D.3.1 Flowmeter
D.3.1.1 Electromagnetic
Flowmeter
D.3.1.2 Ultrasonic Flowmeter
D.3.2 Volumetric Piston
Water Meter
ISO 4064-1: 2005
Measurement of Water Flow in fully charged closed conduits – Meters for cold potable water
and hot water – Part 1 - Specification
D.3.2.1 Plastic Volumetric
Water Meter
D.3.2.2 Brass Volumetric
Water Meter
D.3.3 Jet Water Meter
D.3.3.1 Multi- Jet Water Meter
D.3.3.2 Single Jet Water Meter
D.3.4 Woltman Water Meter
39
CATEGORY E: WATER SUPPLY PLUMBING SYSTEM
E.1 TAP E.2 VALVES E.3 FLUSHING CISTERNS E.4 BIDETS E.5 DRINKING FOUNTAIN
No. Product Standards referred by industry Standard for SPAN
registration Remarks
Standard No. Standard Title
CATEGORY E – SANITARY FITTINGS
E.1.1 Pillar Tap / Bib Tap /
Mixer / Faucet / Shower
BS 5412:1996
Specification for Low Resistance Single Taps and Combination Tap Assemblies
(Nominal Size ½ and ¾) Suitable for Operation at PN 10 max. and a min. flow pressure
of 0.01MPa (0.1 bar)
BS EN 200 : 2008
Sanitary Tapware. Single Taps and combination Taps For
Water Supply Systems of Type 1 and Type 2. General Technical Specification.
Cl. 8.3, Cl.9 & Cl. 10
AS / NZS 3718 : 2005 Water Supply – Tap ware
E.2.1 WC Flushing Cistern &
Flush Pipe MS 795 : 2002
Specification for WC Flushing Cisterns & Flush Pipes
E.2.2 Plastic WC Flushing MS 795 : 2002 Specification for WC Flushing
40
No. Product Standards referred by industry Standard for SPAN
registration Remarks
Standard No. Standard Title
Cistern Cisterns & Flush Pipes
E.3 Vitreous China Water
Closet Pans MS 1522 : 2007
Vitreous China Water Closet Pans – Specification (Second
Revision)
E.4 Vitreous China
Moulded One-Piece Water Closet
MS 1522 : 2007 Vitreous China Water Closet Pans – Specification (Second
Revision)
MS 795 : 2002 Specification for WC Flushing
Cisterns & Flush Pipes
MS 147 : 2001 Specification For Quality of
Vitreous China Sanitary Appliances (First Revision)
E.5 Vitreous China
Sanitary Appliances MS 147 : 2001
Specification For Quality of Vitreous China Sanitary
Appliances (First Revision)
E.5.1 Urinal MS 147 : 2001
Specification For Quality of Vitreous China Sanitary Appliances (First Revision)
E.5.2 Cistern & Covers MS 147 : 2001
Specification For Quality of Vitreous China Sanitary Appliances (First Revision)
E.5.3 Wash Basin MS 147 : 2001
Specification For Quality of Vitreous China Sanitary Appliances (First Revision)