lift table diy plans

DIY WORKSHOP TABLE LIFT

24.000

32.000 2.500

14.500

21.000

16.000

12.000 16.000

1.500 Angle Steel

4.000 4.000

1.500

2.500

2.500

Weld in 2.5" x 12" x 1/8" Flat metal (Both Sides)

Weld in 2.5" x 21" x 1/8" Flat metal

1.500 1.500

Both Upper & Lower Framesare the same dimensions and

Welded together using:

1 1/2" x 1 1/2" x 1/8" Angle Steel

7.000 7.000

6.000

6.000

6.000

6.000

6.500 .750

9.000 9.000

5.000 5.000

1.000

1.000

.250 x 16

Both Upper & Lower Framesare the same dimensions and

Welded together using:

1 1/2" x 1 1/2" x 1/8" Angle Steel( SEE - LOWER FRAME for Fabrication Dimensions )

Holes have same dimensions as Wood Table Top

1.000 1.500

17.750

29.500 29.500

19.750

.500

14.250

14.250

.500

28.500

.375 x 3 Holes

19.750 1.000

1.000

LOWER HINGE LEGS & UPPER WHEEL LEGSare the same dimensions

and welded together Using :

1" x 1" x 0.120" Square Steel Tubing

19.875

1.500 1.000

29.500

21.875

21.875 1.000

1.000

.500

14.250

14.250

.500

28.500

.375 x 3 Holes

UPPER HINGE LEGS & LOWER WHEEL LEGSare the same dimensions

and welded together Using :


.188

.250

17.250

1.250

3.000 45.00

4.000

2.500

.188

1.000

17.625 is the important dimension

Weld on a 5/8" Nut

6.250

1.000

.500

.500

.375 x 2 Holes

You can use 5/8" (UNC) Thread .

or 5/8" ACME Thread(ACME Thread is Much More Expensive)

Both Thread Support Bracesare the same dimenstions

and welded together using :


Side Tabs : 1" x 2 1/2" x 3/16" Flat steel

( You can modify this part shape as long as it's width is 17.625" )

Weld Nut on one and a Washer on the other

I cut my wheels out of Delrin on the Latheand drilled a 0.375" hole in each wheel

.500

1.375

1.375 O.D. .375 Hole

8 count -- 2.75" Long


( Brass Washers next to Wheels )

I am sure you can figure out the Nuts & Washers

You can Use Plastic, Delrin, or Bearings for the Wheels

The important dimension is the wheel O.D. needs to be 1.375"

ALL BOLTS ARE 3/8" (UNC)

ALL Flathead Machine Screws are 1/4" (UNC)

16 count -- 1.125" Long


Sheet1Drawing View4

DIY WORKSHOP LIFT TABLE 1.PDFSheet1Drawing View2



Lower Frame Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4

Upper Frame Dimensions.PDFSheet1Drawing View1Drawing View2

Lower Hinge Legs Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4

Upper Hinge Legs Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4

Threaded Supports Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4

Wheels and Fasteners.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4Drawing View5Drawing View6

lift table diy plans

Documents