diyhuntress diy wooden bench plans diy wooden chevron bench plans - 10 step 6 begin attaching top...

Download DIYHUNTRESS DIY WOODEN BENCH PLANS diy wooden chevron bench plans - 10 STEP 6 Begin attaching top pieces

If you can't read please download the document

Post on 11-Jun-2020

2 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • diy wooden chevron bench plans - diyhuntress.com

  • diy wooden chevron bench plans - diyhuntress.com

    2

    DIMENSIONS & DISCLAIMER:

    Please double check the overall dimensions for your specific build

    before starting.

    Please wear appropriate safety gear when operating power tools.

    DIY Huntress is not responsible for any injury or mismeasurement caused by individual error. For my full disclaimer policy, please visit my

    website at diyhuntress.com/aboutme.

    In better news, thank you for downloading my plan! Please share your build on social media by tagging it to #diyhuntress or #diyhunted.

    Happy DIY’ing!

  • diy wooden chevron bench plans - diyhuntress.com

    3

    WHAT YOU’LL NEED

    TOOLS: Miter Saw Table Saw Nail Gun Dril l/Driver

    Pocket Hole Jig Sander Measuring Tape Pencil

    MATERIALS: (1) Half Sheet 1/2”Plywood (1) 4 x 4 x 96” Board (2) 2 x 4 x 96” Boards (4) 1 x 6 x 96” Boards Carpenter’s Wood Glue

    1 ¼” Brad Nails 1” Brad Nails 1” Wood Screws 2 ½” Pocket Hole Screws Paint, Stain, Sealer

    CUT LIST: Plywood: (1) Top @ 15 x 40” 2x4’s: (2) Long Frames @ 40 ½” (4) Short Side Frames @ 8” (2) Middle Beams Cut @ 48 Angles (see plans & cut l ist) 4x4’s: (4) Legs @ 17” 1x6’s: (2) Long Trim @ 1 ¼ x 41 ½” (2) Short Trim @ 1 ¼ x 15” Top Panel Pieces* * Follow instructions in plans to make the cuts for 1x6’s used on top panel.

  • diy wooden chevron bench plans - diyhuntress.com

    4

    CUT LIST

  • diy wooden chevron bench plans - diyhuntress.com

    5

    THE STEPS:

    STEP 1

    Assemble your first two frames (these wil l be your sides) by attaching the small frame pieces to your legs with 2 ½” pocket hole screws &

    wood glue. Make sure to center the short frames on the legs.

  • diy wooden chevron bench plans - diyhuntress.com

    6

    STEP 2

    Add the long frames to attach the two frames with 2 ½” pocket hole screws and wood glue. Make sure to center the beams when attaching.

  • diy wooden chevron bench plans - diyhuntress.com

    7

    STEP 3

    Attach your angled pieces (cut at 48° on both ends) to the top and bottom long pieces with 2 ½” pocket hole screws and wood glue.

    At this point, you may want to fi l l holes, sand, and paint your base

    before attaching the top.

  • diy wooden chevron bench plans - diyhuntress.com

    8

    STEP 4

    Attach your plywood panel to the top of your bench. Secure to the frame with wood glue and countersunk wood screws.

  • diy wooden chevron bench plans - diyhuntress.com

    9

    STEP 5

    Prep your bench top for artwork. Use a pencil and straightedge to split your plywood into four equal parts.

  • diy wooden chevron bench plans - diyhuntress.com

    10

    STEP 6

    Begin attaching top pieces to the bench with brad nails & wood glue. Cut al l inside angles at 45° and trim the outside pieces either as you

    go, or at the end.*

    * For a ful l step-by-step tutorial of this process with photos, please watch the YouTube video tutorial @ youtube.com.diyhuntress

  • diy wooden chevron bench plans - diyhuntress.com

    11

    STEP 7

    Add your trim pieces (cut from your 1x6) with wood glue and brad nails.

  • diy wooden chevron bench plans - diyhuntress.com

    12

    STEP 8

    Add finishing touches to the bench. Sand, stain, and seal the top. Make sure to use an outdoor stain and sealer if leaving the bench outdoors.

Recommended

View more >