lcd monitor service manual ce42lm4r-e - c&c...
TRANSCRIPT
Part No. 1KA6P2P0001-- N4JJ SEPTEMBER 2006 Reference No. SM1110001-00
LCD MonitorService Manual
Give complete "SERVICE REF. NO." for partsorder or servicing, it is shown on the rating sheeton the cabinet back of the TV set.
NoteThis TV receiver will not work properly in foreigncountries where the television transmission system and power source differ from the designspecifications. Refer to the specifications for thedesign specifications
ContentsSafety precautions/Specifications ..................................................................................................................2Service Mode/Option settings ....................................................................................................................3~7HDMI / PC / Component Signal Support Timing List......................................................................................8Cabinet Disassembly ................................................................................................................................9~11Block Diagram ..............................................................................................................................................12Power Diagram ............................................................................................................................................13Power and Control Diagram ........................................................................................................................14RS232 Settings ......................................................................................................................................15~16Troubleshooting ............................................................................................................................................17IC Descriptions........................................................................................................................................18~19IC Block Diagrams........................................................................................................................................................................20~26Cabinet Parts List ........................................................................................................................................27Pin description of semiconductors ................................................................................................................28Electric Parts List ..........................................................................................................................................29
Model CE42LM4R-E
Service Ref. No. CE42LM4R-E-00
PRODUCT CODE: 113003908
ORIGINAL VERSION: Chassis No.UK4-B
Please use Schematic Diagram 1KA6P2P0005--inserted with this Service Manual.
CE42LM4R-E
FILE NO.
-2-N4JJ
SAFETY PRECAUTION
PRODUCT SAFETY NOTICE
SPECIFICATIONS
Product safety should be considered when a component replacement is made in any area of a receiver. Componentsindicated by mark in the parts list and the schematic diagram designate components in which safety can be of special significance. It is particularly recommended that only parts designated on the parts list in this manual be usedfor component replacement designated by mark . No deviations from resistance wattage or voltage ratings may bemade for replacement items designated by mark .!
!
!
1: An isolation transformer should be connected in thepower line between the receiver and the AC line when aservice is performed on the primary of the convertertransformer of the set.
2: Comply with all caution and safety-related notesprovided on the cabinet back, inside the cabinet, on the chassis or the picture tube.
3: When replacing a chassis in the cabinet, always be cer-tain that all the protective devices are installed properly,such as, control knobs, adjustment covers or shields,barriers, isolation resistor-capacitor networks etc. Beforereturning any television to the customer, the service tech-nician must be sure that it is completely safe to operatewithout danger of electrical shock.
Power source AC 220~240V, 50HzTelevision system System I B/G, D/K, L/L’Colour system PAL/NTSC4.43 (PAL/NTSC4.43/NTSC3.58 IN AV MODE)Receiving channel UHF: 21~69
VHF: E2-E12, F2-F10, R1-R12CATV: X, Y, S1-S41, B-Q
Aerial input impedance 75ohmAV terminal
AV1: CENELEC standardINPUT: Composite video, RGB and Audio L/R
OUTPUT: TV-output with composite video and audio L/R AV2: BNC
INPUT: RGB, H and V / Y, Pb, Pr and audio L/ROUTPUT: RGB, H and V / Y, Pb, Pr
AV3: BNCINPUT: Composite video
OUTPUT: Composite videoAudio M.Out Cinch: L/RHDMI
INPUT: HDMI GROUP StandardPC INPUT:Serial Port RS232C
INPUT/OUTPUT:Contrast Ratio 800:1Display Resolution 1366 x 768 (WXGA)Viewing Angles H: 178°, V: 178°Dimensions (WxHxD) 1050 x 654 x 150 Weight 36 Kg
Important recycling information.
Your SANYO product is designed andmanufactured with high quality materialsand components which can be recycledand reused.
This symbol means that electrical andelectronic equipment, at their end-of-life,should be disposed of seprately.
In the European Union there are separate collection systems forused electrical and electronic products.
Please help us to conserve the environment we live in!
Note: This symbol mark and recycle system are applied only to EU countries and are not applied to other countries of the world.
RoHS.This product does not contain any hazardous substances prohibited by the RoHS Directive.(You will find “R” or “Z” at the last digit of the serial number or an “RSF” label near the rating plate on the RoHS compliant product.)
WARNING.You are requested to use RoHS compliant parts for maintenance or repair..You are requested to use lead-free solder .
!
!
-3-N4JJ
HOTEL MODETo enter Hotel Mode press and hold the green button on the remote control for 3 seconds.Hotel Mode allows the user to set up the function of the set
SERVICE MODETo enter Service Mode press and hold the green button on the remote control whilst pressing the 6 button on the tv cabinet at the same time,alternatively:-From Hotel Mode press and hold the green button on the remote control for 3 seconds
To select the service item and change data value
+ To select the adjustment item, use the 5 or 6 buttons.+ To change the service data, use the Volume - (LEFT) or Volume + (RIGHT) buttons.+ The data which is set in the service mode is stored into the memory IC automatically
EXAMPLE: 000 UK4B 07.45
ITEM NO SECTION VALUEITEM
EXIT FROM THE SERVICE MODE+ Press the MENU button or turn off the TV set by using the Mains switch.
-4-N4JJ
SERVICE DATA
-5-N4JJ
SERVICE DATA (contd.1)
-6-N4JJ
SERVICE DATA (contd.2)
-7-N4JJ
SERVICE DATA (contd.3)
-8-N4JJ
HDMI / PC / COMPONENT SIGNAL SUPPORT TIMING LIST
ResolutionHorizontalFrequency
(kHz)
VerticalFrequency
(Hz)Remark
720_400 31.47 70.09 DOS(VGA )
640_480 31.50 60.00 DOS(VGA VESA 60Hz)
640_480 37.50 75.00 VGA VESA 75Hz640_480 37.86 72.81 VGA VESA 70Hz
640_480 37.86 74.38 VGA640_480 35.00 67.00 Mac.640_480 34.97 66.60 Mac LC 13"
800_600 35.16 56.25 SVGA VESA 56Hz800_600 37.90 60.32 SVGA VESA 60Hz800_600 46.90 75.00 SVGA VESA 75Hz
800_600 32.70 51.09 SVGA800_600 34.50 55.38 SVGA
800_600 37.90 61.03 SVGA800_600 38.00 60.51 SVGA800_600 38.60 60.31 SVGA
832_624 49.00 74.00 Mac.1024_768 48.40 60.00 XGA VESA 60Hz1024_768 56.50 70.00 XGA VESA 70Hz
1024_768 60.000 75.00 XGA VESA 75Hz1024_768 44.00 54.58 XGA
1024_768 46.90 58.20 XGA1024_768 47.00 58.30 XGA1024_768 48.50 60.02 XGA
1024_768 58.03 72.00 XGA1024_768 60.31 74.92 XGA1024_768 61.00 75.70 XGA
1024_768 60.24 75.08 MAC_Norma l 19"1280_960 60.00 60.00 SXGA VESA 60Hz
1280_1024 79.976 75.025 SXGA VESA 75Hz1280_1024 62.50 58.60 SXGA1280_1024 63.370 60.01 SXGA
1280_1024 63.34 59.98 SXGA1280_1024 63.74 60.01 SXGA1280_1024 63.79 60.18 SXGA
1280_1024 63.90 60.00 SXGA1280_1024 71.69 67.19 SXGA
1280_1024 76.97 72.00 SXGA1280_1024 81.13 76.107 SXGA1152_864 64.20 70.40 SXGA
1152_900 61.20 65.20 SXGA1152_900 61.85 66.00 SXGA1152_900 71.40 75.60 SXGA
1152_870 68.68 75.06 MAC_Norma l 21"1280_960 75.00 75.08 Mac.
1280_1024 80.00 75.00 Mac_.1600_1200 75.00 60.00 UXGA VESA 60Hz
Resolution Horizontalfrequency (KHz)
Vertical frequency(Hz)
Dot Clock Frequency(Mhz)
Remark
720x480 15.735 60i 12.27 SDTV 480i720x576 15.625 50i 13.50 SDTV 576i720x480 31.25 60p 27 SDTV 480p720x576 31.25 50p 27 HDTV 576p1280x720 45.00 60p 74.25 HDTV 720p1280x720 37.50 50p 74.25 HDTV 720p1920x1080 33.75 60i 74.25 HDTV 1080i1920x1080 28.13 50i 74.25 HDTV 1080i1920x1080 31.25 50i 74.25 HDTV 1152i
-9-N4JJ
Mechanical Disassemblies (CE42LM4R-E)1. Rear Plate RemovalRemove screws (A)Before removing the Rear Plate, remove the screw from the Earth wire (B)
-10-N4JJ
Location of Circuit Board and Electric Parts
2. Chassis and fan removal
Screw A : M3 x 6
Note: Control Board is fixed on Cabinet Front.
Mechanical disassemblies cont.
-11-N4JJ
3. Cabinet Back Removal
(1) Remove the lead wire of Control Board from Main Board.
(2) Remove the lead wire of inverter from Power Board / Main Board.
(3) Remove the LVDS cable from the LCD Panel
(4) Remove cables from Inverter area or power and main board
(5) Remove screw A (20 pcs).
(6) Remove the Cabinet Back.
A A A A A A
A
A
A
A
AA A A A A
A
A
A
A
Mechanical disassemblies cont.
-12-N4JJ
BLOCK DIAGRAM
This is a diagram for all models and therefore differs slightly from the actual block diagram.
LCD PANELS
CA
LER
Digital Interface ADC
D-RGB
TEXT/OSD MIX
YC
IF
VIDEO SWITCH
RGB/YPBPR
VIFIN1 LOC2
PANELLVDS
VIF
TUNER
GTV
SCART1
CVBS1
TV OUT (CVBS)
RGB1
CVBS3
RGBSWITCH
VIDEOSWITCH
BA7652
SVO6/CVBS6CVBS
CVBS_Y4
CVBS_Y5
SWO1_CVBS20_Y20
CVBS30_Y30
DVBO_IFVO_FMRO
HDMI
TMDS
BA7603
SiI9021
HDMIDECODER
D-RGB
RGB
CV
BS
PV
10_23
IN_R
IN_G
IN_B
R3_PR31G3_Y31
B3_PB31
PC
RGBRGB
SWITCH
BA7657
MATRIX
COMPONENT
YPBPR RGB
H/V
Y/G
Pb/B
H/V
Pr/R
H
V
OUT IN
OUT
IN
Outline
-13-N4JJ
1 2 3 4 5 6
KQ
1
1
PO
WE
R 1
ON
/OF
F
IC66
046V
PO
WE
R 4
PA
NE
L O
N
ON
/OF
FIC
6613
IC66
00
IC66
01
5V3V3
ST
B
5V S
TB
24V
IC66
10
IC66
09
IC66
08
IC66
07
IC66
06
IC66
05
IC66
03
IC66
02
13V
_PW
R
9V 12V
_FA
N
5V_S
W
3V3_
SW
D5V
D3V
3
1V8_
SW
D1V
8
PO
WE
R
AR
CH
ITE
CT
UR
E
D66
01
D66
21
D66
18
D66
16
D66
07
D66
06
D66
05
D66
04
D66
15
D66
14
TO
IC80
1P
IN E
10
5V
1 2 3 4 5KQ
24V
6V
D3V
3
D5V
3V3_
SW
5V_S
W
12V
_FA
N
9V
PR
OT
EC
T
AR
CH
ITE
CT
UR
E
2 3 4 5 KR
PO
WE
R
TO
UN
IT
PO
WE
R D
IAG
RA
M F
OR
UK
4B
-14-N4JJ
Power and Control Diagram
PJ-NET
POWER CONNECTOR MAIN
SUB-AV-BNC
SUB-AV SOCKET
1KA9W0640017-
K2009
TX
RX
5V
5V
3.3V
12V
3.3V
5V cct
K2014
K2013
K2006
KCPA
TO G19
KCP
IC1551
1AA93ABAF300X
KG 1 2 3 4
P_FAIL
5V1A
KA
KQ
16V Main Supply
1
8
1
5
12V
5V
3.3V
K3000
cct
K3A 12V
K3003 K603
K303-03
K3Q
K3R KR
5V S/B
K605 K3002
K605-02 5V
gnd
16V
12V
Gnd
Gnd
Gnd
Gnd
NC
NC
NC
NC 1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14 5V S/By
Gnd
D5V
Power on
ON/OFF
VBR
NC
NC
NC
NC
Gnd
Gnd
K3001
NC
NC
NC
NC
NC
1
11
1
6
POWER_3
BL_ADJ
BL_ON
3.3V S/B
KP R1600
R1601
gnd
1AA0B10H086JA
1AA0B10H087D01AA0B10H086JB1AA0B10H086G0
-15-N4JJ
The TV control commands are used to control a TV through RS232C from a computer.Serial Interface SpecificationTransfer Specification1. Transmission Speed : initial setting value is 192002. Transmission speed can be changed by hotel mode
ConnectionThe designated RS232C serial cable that is provided with the LCD monitor must be used for a connection between a computer and a LCD monitor
The TV command is defined by one command / one line that starts with “C” and ends with carriage return (0x0D)There are two types of commands:1. Functional Execution Commands e.g. Co5[CR] (see table on following page)2. Status Read Commands e.g. “CR0 [CR] (see table on following page)
Setting the monitor address in RS232 modeTo access hotel mode press the green button on the remote control and hold for 5 seconds. The following screen will appear
Each monitor can have a specific address e.g. 007 which helps command that monitor individually and will not affect other monitors connected toa controlling pc.
Address format commandThe adressing format command is used for operating multiple monitor sets from a single pc via the RS232 command line. If you set your monitoraddress to ‘000’ it will never respond to any addressing command from the pc. If the address from the pc is ‘FFF’, all monitor sets will execute thecommand. The address format command is defined by one command, one line which starts with ‘A’ and ends with carriage return (0x0D). An address isadded at the top of a control command.Example:Functional execution command: “A001C05” [CR] means the address is 001 and the control command is C05Status read command: “A001CR0” [CR] means the address is 001 and the command is CR0
The monitor can set its own address in the hotel option (see above). The address range is 000 - 999, the default address will be 000.The baud rate indicates the unit transfer speed of data from the pc the the monitor sets.
RS232C SETTINGS
ITEM SPECIFICATION
Synchronous system AsynchronousTransmission Speed 9600 / 19200Data Length 8 bitParity NoneStop BitFlow Control None
1
123456789
123456789
(D-Sub 9 Pin) (D-Sub 9 Pin)
CD
RXD
TXDDTR
SG
DSR
RTS
CTS
RING
N.C.
RXDTXD
N.C
SG
N.C
RTS
CTS
N.C.
MENU
Hotel mode ON / OFFOn program OFF/ 1~99Preset ON / OFFAddress 007Baud Rate 19200
/ AV1-AV3 /RGB/ HDMI/ PC
Hotel
: Select : Adjust : Exit
-16-N4JJ
Functional Execution Command Table
Command Item Comment
Toggle (Dynamic, Standard, Eco, Personal)
“---”_means “No Function”
CF DEA RMCN
CF DEA RMCY
CF CLOK OFF
CF CLOK ON
CF DPMS OFF
CF DPMS ON
C92C64
C76
C75
C74
C73C72
C71
C70C30
C0F
C29
C28
C27
C26C25
C24C23
C01
C00
Picture
AV1 direct
Wide “Normal” direct
Wide “Full” direct
POWER ONPOWER OFFWide “Auto” direct
Wide “Natural” direct
Wide “Zoom 16:9” direct
Wide “Title in 16:9” directWide “Zoom 14:9” direct
Wide “Title in 14:9” direct
RGB direct
AV2 RGBHV direct
AV2 YPbPr direct
AV3 direct
HDMI direct
PC direct
PC Auto adjustFactory settings
Power save ONPower save OFF
Child lock ON
Child lock OFF
RC inhibition OFF
RC inhibition ON
Status Read Command TableCommand Item Note
“---”_means “No Function”
C** Panel operating time
CR0
CR1
CR WIDE
CR PICTURE
CR SIGNAL
CR CHILD
CR DPMS
Power
Input mode
Wide mode
Picture mode
Signal existance
Child lock
DPMS
On, Standby, Power error,...
AV1, AV2, ..., HDMI, PC
Auto, Normal, Full, ...
Dynamic, Standard, ...
Signal / No signal
On / Off
On / Off
RS232C Command Tables
-17-N4JJ
TROUBLE SHOOTING
Item Condition Check point
1
2
3
4
5
6
7
8
9
No power
No power
No power
No backlight
Faulty picture
Faulty picture
No RC
No key SW
Fan faulty
** HINT**In most cases the problem is caused by the SUB POWER board or COMPboard.
Try replacing them first, then check the LCD panel.
NO LED
NO LED
LED brighter
After power on, once panel lightsthen keep black out
No colour, poor pictureDarker / brighter picture etc.
Visible line on the picturePart of the display is poor
No working of RC handset
No working or the front key Switch
After indication of the display,then 30 seconds later, come intostandby
Change the FAN
Change the FRONT board
Change the RC or FRONT board
Change the panel
Change the COMP board>>If not, change the panel.
Change the LCD panel
Check to voltage of KR-3 --- 5V
>>Change the power board
Check the fuse on the FILTER board
Check the connection of the AC cord.(AC plug and junction part)
Check the voltage of
Housing KQ-2 ----13V
IC6602 ---- 9V
IC6603 ---- 12V
IC6604 ---- 6V
Housing KR-1 ---- 24V
>>Change the COMP or SUB POWER board
** Refer to the power diagram
-18-N4JJ
IC Descriptions for UK4BIC1110This is a switching IC, NJM2233BM, which allows the sync signal input on monitor sets to be switched between pin20 of SCART 1 (conventional) and pin 14 of SCART 1 (SIS signal). The IC takes a 5V supply and is switched by thecontrol line SIS.
IC1205This a ROHM BA7603F triple video switch which allows the RGB input to be switched between SCART 1 andSCART 2. The switch is controlled by the RGB_SW line from the IC.
IC1271This a large multiway electronic switch, MM1631BJBE. Via the I2C lines the cpu can select any audio input L/R pairand feed them to scart 3 or IC801.
IC151BA2904F - this is an OP-AMP used to amplify the AGC voltage back to IC801.
IC1801/1802PCA9534PW - These are I2C expander IC’s. They convert I2C commands from IC801 into control lines.
IC1841/1851These are OP-AMPS used to control the speed of the fans
IC2002/20036db AMP/BUFFERS that compensate for internal loss in the YPbPr / RGB / HV loop.
IC2006RS232 to 5v decoder / encoder. It converts the RS232 signal from K2008 into a TTL signal that can be understoodby the CPU IC2010
IC2007 / 8 / 115v to 3.3v logic conversion for the CPU IC2010
IC2009Reset pulse generator for the CPU IC2010
IC2010CPU with internal program flash memory. The software version programmed into this device can be found in theservice menu. The RS232 data is converted into I2C data by this CPU and fed to the main CPU via KCPA.All RS232 protocol are generated by this IC.
IC2012This is a 5v regulator.
IC4001This is a SST SST39VF020 CMOS multi-purpose flash with a capacity of 2Mbits. It is connected to the LOC usingaddress lines, data input/output, write enable and control lines. The flash IC is powered by the 3V3 SW supply.
IC4002This is a ROHM BD5260G open drain voltage detector IC which works in conjunction with the main power and the3.3V standby line to control the back lights.
IC601This is a “current mode PFC controller” operating in transition mode. It is used in conjunction with L603 as activepower phase correction.
-19-N4JJ
IC Descriptions for UK4B (continued)IC6600This is an LA5754 voltage regulator. It provides the 12v supply for the LCD panel.
IC6601This is a BA33BC0FP voltage regulator. It converts the 5v standby supply to 3.3v.
IC6602This is a BA09FP-E2 voltage regulator. It converts 13v to 9v.
IC6603This is a BA12FP-E2 12v voltage regulator. It converts the main 13v supply down to 12v for the fan.
IC6604This is a LA5754MP voltage regulator. This IC converts the main 13v supply down to 6v. IC801 can switch this IC onand off via control line “Power 1”. Consequently all supplies developed from this 6v will also be switched (see powerarchitecture diagram on page 8)
IC6605 / 6 / 7 / 8 / 9 / 10These are voltage regulators which convert the switched 6v supply down to 5v, 3.3v and 1.8v.
IC6613This is a TC7SH02 2-INPUT NOR GATE. This IC controls the 5v power to the LCD panel. It is switched via controllines “Power 4” and “Panel on”.
IC701This is a THC63LVDM83R LVDS converter IC. This IC converts 3 sets of 8 bit data (R, G & B) into 4 channel andclock data stream to the LCD panel.
IC8001This is a HDMI receiver / convertor. HDMI data from K1006 is fed into this IC. The IC then extracts the video andaudio in digital format and sends the data to IC801. Audio data is converted to analogue via IC8501
IC801This IC is the main control IC for the entire TV. It incorporates:-1) CPU for control and on-screen graphics presentation.2) Video signal processor for controlling picture presentation and quality.3) LCD scaler for converting different resolutions to the resolution of the LCD.4) 100 page text decoder.5) Stereo sound decoder.6) Multi-system decoder (PAL, NTSC, SECAM etc.)
IC802This is an 8K x 8 bit EEProm. It is used to store all the calibration data and user settings. When a new IC is fitted,the CPU (IC801) will detect it and initialise the IC to the default factory settings.
IC8131This is a 512 x 8 bit EEProm. It is used to store the resolutions that the tv is able to display along with the manufac-turer, date of manufacture and model number. An external device (eg DVD) with HDMI will read this EEProm todetermine which resolution signal to send to the tv.
IC8141This is an I2C isolation device
IC8501This is a digital to analogue converter. It is used to convert the HDMI digital audio data to analogue.
IC8502This is a dual OP-AMP and is used to bufffer the HDMI analogue signal to the audio selector IC (IC1271)
-20-N4JJ
xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx
Fig
1.
Blo
ck d
iagr
am o
f LO
C II
QS
S S
OU
ND
IF
AG
CQ
SS
MIX
ER
AM
DE
MO
DU
LAT
OR
VIS
ION
IF/A
GC
/AF
CP
LL D
EM
OD
.
VID
EO
AM
P.
SO
UN
D T
RA
PG
RO
UP
DE
LA
Y
VID
EO
SW
ITC
HV
IDE
O ID
EN
T.
VID
EO
FIL
TE
RS
PA
L/S
EC
AM
/NT
SC
H/V
SY
NC
SE
P.
H-O
SC
. + P
LL
SIF
IN/D
VB
IN
AG
CO
UT
VIF
IN
CV
BS
3/Y
4
C5/
C6
CV
BS
/30
C4
/C30
CV
BS
O/P
IP
SS
IF
AU
DIO
CO
NT
RO
L
DV
BO
/FM
RO
SW
ITC
H
CV
BS
2/Y
5
IFV
O/S
VO
/
YS
YN
C
DV
BO
/IFV
O/
QS
SO
/
SO
UN
D P
LLD
EE
MP
HA
SIS
CV
BS
/Y6
SV
O/F
MR
O
BA
SE
-BA
ND
FLA
SH
OS
D
LIN
EM
EM
OR
Y
OV
ER
LAY
MIX
ER
AM
OU
T
DE
LAY
LIN
E
DE
CO
DE
R
Y /
CV
BS
/ R
GB
/ Y
PR
PB
SW
ITC
H
CVBS20 / Y20INSW2 / C20
R2 / PR / C21
G / YIN2 /
B / PBIN2CVBS / YOUT
INSSW3R / PRIN3 / C31
B /PBIN3
G / YIN3 /
CVBS / Y21
CVBS / Y31
H/V
sync
Y/C
VB
S
C/C
VB
S
UV
AN
TI
ALI
AS
FIL
TE
RS
AU
DIO
DS
P
DA
Cs
AU
DIO
SE
LEC
T
AD
Cs
/ DA
Cs
AD
Cs
TB
CA
GC
2D/3
D
CO
MB
FIL
TE
R
RD
SC
VB
S/Y
U V
DE
INT
ER
-LA
CE
R
NO
ISE
RE
DU
CT
.
BLA
CK
ST
RE
TC
HW
HIT
E S
TR
ET
CH
HO
RIZ
. SC
ALE
RP
EA
KIN
G /
LTI /
CT
IC
OLO
R F
EAT
UR
ES
YU
VTO RG
BM
AT
RIX
AD
C
ST
ER
EO
SO
UN
DD
EC
OD
ER
AU
DIO
IN/O
UT
LIN
E O
/IC
, SC
, SW
I2S
HP
-OU
TL
S-O
UT
ME
MO
RY
INT
ER
FA
CE
CNTRL
ADDR
DATA
612
16
16 M
Bit
SD
RA
M
8051
MIC
RO
-
CO
NT
R.
TX
TD
EC
OD
ER
OS
D
OS
D
BLE
ND
ER
I/Os
24
RG
B/Y
UV
alph
a
OU
TP
UT
FO
RM
AT
RG
B
DA
Cs
RG
B/
ITU
H, V
,C
LK,
Clk
Ref 4
30/1
0
RO
GO
BO
AM
DIG
ITA
LV
IDE
OO
UT
PA
R.
VID
EO
INT
ER
-FA
CE
IN_RIN_GIN_B
SOGINRBIAS
AHSAVS
ACLK
ASCLASDA
I2C
HIF
LPLL
TE
ST
IMA
GE
GE
N.
INP
UT
SE
LEC
T
RG
B 2
4R
GB
24
YU
V 2
4R
GB
24
YU
V 2
4
AU
TO
AD
JUS
TC
OLO
RM
AT
RIX
HO
RIZ
. / V
ER
T.
UP
/ D
OW
NS
CA
LER
OU
TP
UT
CO
LOR
LOO
K-U
PTA
BLE
DIT
HE
RU
NIT
OU
TP
UT
INT
ER
FA
CE
LVD
S A
ND
TT
L
RS
P[1
3:0]
RS
N[1
3:0]
RG
B18
/R
GB
24R
GB
30
RG
B24
YU
V24
CR
YS
TA
LO
SC
ILLA
TO
R
PA
NE
LP
LL
FLA
SH
INT
ER
FA
CE
GLO
BA
LC
ON
TR
OL
UN
IT
ON
-CH
IPM
ICR
OC
ON
TR
OLL
ER
80C
51
TIM
ER
CO
UN
TE
RU
AR
TI2
C
RX
CT
XD
SC
LS
DA
GP
IOP
WM
GP
IO[2
3:16
]G
PIO
[15:
0]P
WM
[2:0
]
INT
_NP
OR
_NR
ST
_NC
FG
[15:
0]
FO
NT
AN
DC
HA
RA
CT
ER
RA
M
T[1
:0]
SR
AM
IC801
IC BLOCK DIAGRAMS
-21-N4JJ
IC BLOCK DIAGRAMS
IC1205 BA7603F
IC151 BA2904
1 2 3 4
5678
CH1
CH2
+
+
_
_
VCC OUT2 -IN2 +IN2
OUT1 -IN1 +IN1 VEE
-22-N4JJ
IC BLOCK DIAGRAMSIC1271 (MM1631)
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
L11
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
BIAS
SC
L
SD
A
AD
R
MU
TE
GN
D
LOUT10dB
VC
C
ROUT10dB
LOUT20dB
ROUT20dB
LOUT30dB
ROUT30dB
BIAS
Logic
33
35
1
3
5
7
9
11
13
15
17
34
36
2
4
6
8
10
12
14
16
18
19
23 22 21 20 24
30
29
28
27
26
25
31 32
IC2002 (TSH3441)
Top View
OUT2
1
IN2
OUT1
+Vcc
2
3
7
8
OUT3
IN1
4
6IN3
GND
SO8
Pin1 identification
5
6dB
6dB
6dB
-23-N4JJ
IC BLOCK DIAGRAMSIC2003 (TC7WH125)
IC2006 (SP3232)
V-
1
2
3
4 13
14
15
16
5
6
7
12
11
10
C1+
V+
C1-
C2+
C2-
R1IN
R2IN
GND
VCC
T1OUT
T2IN
8 9
SP3232E
T1IN
R1OUT
R2OUT
T2OUT
IC2007 / IC2008 / IC2011 (TC7SET08)
-24-N4JJ
IC BLOCK DIAGRAMSIC2009 (BD4828)
VDD
GND
VOUT
Vref
IC2010 (R5F21162)
1 2 3 4 5 6 7 8
91011
1213141516
29282726
25
24 23 22 21 20 19 18 17
323130
R8C/11 Group
XIN
/P46
XO
UT/P
47(N
ote
1)V
SS
RE
SE
T
VC
C
CN
VS
S
P17
/INT
1/C
NT
R0
P16/CLK0
P15/RxD0
P14/TxD0
P37
/TxD
10/ R
xD1
P30
/CN
TR
0/C
MP
1 0
P33
/INT
3/
P31
/TZ
OU
T/C
MP
11
P32
/I NT
2/C
NT
R1 /
CM
P12
IVC
C3
AV
SS
AV
CC/V
RE
F
P03/AN4
P02/AN5
P01/AN6
P00/AN7/TxD11
P06/AN1
P05/AN2
P04/AN3
P45/INT0
P10/KI0/AN8/CMP00
P11/KI1/AN9/CMP01
P12/KI2/AN10/CMP02
P13/KI3/AN11
P07
/AN
0
MODE
TC
IN
IC2012 (BA50BC0FP)
Vref
TSD 0CP
+
_Driver
R1
R2
Vcc (1 PIN) N. C. (2 PIN) OUT (3 PIN)
GND (FIN)
-25-N4JJ
IC BLOCK DIAGRAMS
IC6600 / IC6604 (LA5754MP-DL-E)
Y-Decoder
I/O Buffers and Data Latches
Address Buffers & Latches
X-Decoder
DQ7-DQ0
Memory Address
OE#
CE#
WE#
SuperFlash Memory
Control Logic
Functional Block Diagram
IC4001 (ST39VF0200)
-26-N4JJ
IC BLOCK DIAGRAMS
IC1801 / IC1802 PCA9534PW
POWER-ONRESET
INPUTFILTER I2C/SMBUS
CONTROL
INPUT/OUTPUTPORTS
WRITE pulse
READ pulse
A0
A1
A2
SCL
SDA
VDD
Vss
8-BIT
I/O0
I/O1
I/O2
I/O3
I/O4
I/O5
I/O6
I/O7
SU01783
NOTE: ALL I/Os ARE SET TO INPUTS AT RESET
Vcc
INTLP
FILTER
PCA9534
IC601 L6562D
+
-
MULTIPLIER AND
VREF2
OVERVOLTAGE
DETECTION
VOLTAGE
REGULATOR
UVLO
INTERNALSUPPLY 7V
+
-
2.5V
R1
R2
R
S
Q
+-
DRIVER
STARTER+
-
ZERO CURRENT
DISABLE
2.1 V1.6 V
Vcc
8
1
2 3 4
ZCD
Vcc
INV
COMP MULT CS
GD7
5
GND
6
25 V
40K
5pF
15 V
Starterstop
DETECTOR
THD OPTIMIZER
-27-N4JJ
CABINET PARTS LIST FOR MODELS CE42LM4R-E-00
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
43
�
JXPLA
11
Security fixing point
Wall mount fixing
positions
6 5
Item Part No. Description Item Part No. Description
2
7
CE42LM4R-E-00CABINET PARTS
1 665 000 7987 FRONT EXTRUSION ASSY N4JJ2 665 000 8557 REAR EXTRUSION ASSY N4JJ3 665 000 8564 ASSY REAR PLATE N4JJ 4 665 000 8014 FRONT ACRYLIC-N4JK5 665 000 6621 CONT BUTT MNTG BRCK N2MJW 6 665 000 6614 IP56 CONTROL BUTTONS 7 665 000 5914 STRAIN RELIEF BUSH HEYCO 8 665 000 8588 FAN BRACKET-N2MJ9 412 075 4003 SPECIAL SCREW 4.2X9.510 412 075 3709 SPECIAL SCREW 4.2X13.0
ACCESSORIES11 645 079 4421 ASSY,REMOCON JXPLA (WEEE)12 665 000 8595 INST MANUAL - N4JJ (1)13 665 000 7239 INSTALL INST SHEET N4JJ
1
9
10
-28-N4JJ
PIN DESCRIPTION OF SEMICONDUCTORS
AK
C
B E
C2C1
B1 B2E
C
CB E
K A
C
B
E
B2B1
C1 C2
E
E
B
C
B2B1
C1 C2
E�
B2
B1C1C2
E1
E2
�
K
A A
A
K K
K
A
K
A
CB
E CB
EC
B
E
1
2
34
5
6
Index
1 2
N
IndexIndex
1 2
N
2
1 3(IN) (OUT)
(GND)
21 4
2
13
Index
1
N
Index1
N
Index1
N
Index1
N
Index1
N
Index
1 N
21
31
2 32
1
3
RESET GND
Vdd
5
3
DG
SD
G
S
K: Cathode�A: Anode
C: Collector�B: Base�E: Emitter
D: Drain�G: Gate�S: Source
● Diode
● Transistor/FET
● IC
E1C2
E2 C1B2
B1
Index
● Diode
● Transistor/FET
● IC
FET
N4JJ
-29-
CHASSIS ELECTRICAL PARTS LIST
Product safety should be considered when a component replacement is made in any area of a receiver. Components indicated by a mark in this parts list and the circuit diagram show components whose value havespecial significance to product safety. It is particularly recommended that only parts specified on the followingparts list be used for components replacement pointed out by the mark .!
!
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
CE42LM4R-E
CHASSIS PARTS1 665 000 8694 COMP N4JK(MAIN+SUB AV)2 665 000 8731 ASSY,PWB,SUB POWER N4JK3 665 000 8748 ASSY,PWB,FILTER N4JK 4 665 000 8465 ASSY,PWB,CONTROL,N4HLW (FITTED ON FRONT EXTRUSION)5 645 068 3763 MOTOR,FAN DC
PANEL SPACER AND GASKET610 323 0641 GASKET 20X60XT20-N3AL610 309 8715 T-COPPER FOIL*1821*W50
LCD PANEL 645 089 8938 LCD(LC420W2-SLA2)665 000 7567 PAD(BLACK)PICHCO RBS-37
OTHER COMPONENT(ELECT)BP-EARTH 665 000 7802 NONSTANDARD WIRE ASSYKK-1 645 040 3002 FERRITE RING & FIXING PINKLP-PN 665 000 7796 NONSTANDARD WIRE ASSY (LVDS CABLE) K602-1 645 020 3640 FERRITE RING(also used in locations K604-1 and W900-1) W900 665 000 8724 CORD, POWER N4JJAC CORD EU 645 054 1155 CORD, POWER-3.0MK-N2DJ AC CORD UK 645 054 1148 CORD, POWER-3.138MK N2DJAC CORD AUS 665 000 8755 AUSTRALIAN CORD IECKCP-KCPA 665 000 7819 NONSTANDARD WIRE ASSY KP-K3001 610 334 4690 STANDARD WIRE ASSY-JPNK2006-IC 665 000 7840 NONSTANDARD WIRE ASSY K3000-K2 610 334 4614 STANDARD WIRE ASSY-JPNK39J-KK 665 000 7826 NONSTANDARD WIRE ASSY K602-201 610 334 4621 STANDARD WIRE ASSY-JPNK603-K03 610 328 4606 STANDARD WIRE ASSY-JPNK604-CN1 610 334 4638 STANDARD WIRE ASSY-JPNK605-K02 610 334 4591 STANDARD WIRE ASSY-JPNK608-601 665 000 7833 NONSTANDARD WIRE ASSYWTU-EXT 665 000 6799 CABLE, ANTENNA EXT N2MJW
12
3
5
4
-30-N4JJ
-31-N4JJ
-32-N4JJ
Sanyo Industries (UK) LtdPrinted in UK