laser measuring tool - appliance parts · product manual laser measuring tool model no. 320°48298...
TRANSCRIPT
Product Manual
Laser Measuring ToolModel No. 320°48298
CAUTION] Read, understand and
follow all Safety Rules and Operatinginstructions in this Manual before
using this product.
• Safety Instructions. Operation• Nlaintenance
• Troubleshooting
Sears, Roebuck and Co,, Hoffman Estates, IL 60179www,craftsman,com
Warranty Page 2
Safety Precautions Page 3-4
Description Page 4-7
Operation Page 7-t6
Maintenance Page 16
Trouble Shooting Page 17
ONE YEAR FULL WARRANTY ON CRAFTSMAN@ PRODUCT
If this Craftsman tool fails to give complete satisfaction within one yearfrom the date of purchase, return it to any Sears store or other Craftsman
outlet in the United States for free replacement.
This warranty applies for only 90 days from the date of purchase if this
product, is ever used for commercial or rental purposes.
This warranty gives you specific legal rights, and you may also have otherrights, which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
SAVE THESE INSTRUCTIONS[
READ ALL INSTRUCTIONS[
CONTENTS AND ACCESSORIES
Laser measuring tool, carrying case
48298 ManuaLRevised_07-0225 Page 2
,_k WARNING: BE SURE to read and understand all instructions in this manual
before using this product. Failure to follow all instructions may result in hazardousradiation exposure, electric shock, and/or bodily injury.
_lk CAUTION; DO NOT attempt to modify the performance of the laser device in
any way. This may result in a dangerous exposure to laser radiation.
_k WARNING: LASER LIGHT. LASER RADIATION. Avoid Direct Eye Exposure.
DO NOT stare into beam. Turn the laser beam on only when using this tool. Class Ilialaser.
_k WARNING: Use of controls, adjustments, or the performance of pro-
cedures other than those specified in this manual may result in hazardousradiation exposure.
,_ WARNING: The use of optical instruments such as, but not limited to, tale _
scopes or transits to view the laser beam will increase eye hazard.
This measuring tool has a built-in laser light. The laser is a Class Ilia and emits out-put power of a maximum 2o5mW and 635-665nm wavelengths. These lasers do notnormally present an optical hazard. However, DO NOT stare at the beam, as this cancause flash blindness.
The following label is on your laser measuring toot. It indicatesthe location from which the laser measuring tool emits the laser
light. Be aware of the laser light location when using the tool.Always make sure that any bystanders in the vicinity of use aremade aware of the dangers of looking directly into the laser.
. Do not remove or deface any product labels.
o Avoid direct eye exposure. The laser beam can causeflash blindness_
o The laser on the laser measuring tool is not a toy.Always keep it out of the reach of children. The laserlight emitted from this device should never be directed
towards any person for any reason.
° Do not operate the tool around children or allowchildren to operate the tool.
• Do not place the tool in a position that may cause anyoneto stare at the laser beam, whether intentionally or
unintentionally.
= Do not use on surfaces such as sheet steel that have
!:: iAVO|D EXPOSURE::La_J;er i*mliiitlon ts emittetl:
: i: ,font tlt!_ _per!twe i: :i:
!:! i LA_5"_Rt, D_! _N-OO_IOT _TANE :
i ;_: imo_t_o,Vicw_mC_v_r,
TIPs ded_e complies with pert
_5of the FCC R./e_ Opnmli_/_
iS subjecf to the fotMwing lweconditions; {It This device maynet cause h_tmfu! interference.
and (2) th_s device mum acceptany infedemnce received,
including inederence fhM may
I! +_]
shiny, reflective surfaces. The shiny surface could reflect the beam back atthe operator.
Always turn the laser tool off when not in use. Leaving the tool on increas-es the risk of someone inadvertently staring into the laser beam.
48298 Manual_Revised_0749225 Page 3
Do not attempt to modify the performance of this laser device in any way,
This may result in a dangerous exposure to laser radiation,
o Do not attempt to repair or disassemble the laser-measuring tool. If unquali-fied persons attempt to repair this product, serious injury may occur. Any
repair required on this laser product should be performed only by authorizedservice personnel.
o Do not operate the tool in combustible areas, such as in the presence of
flammable liquids, gases, or dust°
o Use of other accessories that have been designed for use with other laser
tools could result in serious injury.
o Keep batteries out of reach of children.
o For further information regarding lasers, refer to ANSI-Z136.1, the Standardfor the Safe Use of Lasers, available from the Laser Institute of America (407)3804 553.
KNOW YOUR LASER MEASURING TOOL (See Fig. 1)
The laser measuring tool is a highly accurate measuring tool for fast, easy operation:
° Measure distances from 1 foot to 150 feet with an accuracy of 4-3/16 inch.
, The laser measuring tool is intended for:
° Measuring distances, lengths, heights, and clearances
o Difficult-to-measure situations: the Pythagorean Theorem mode allowsindirect measurement
° Calculating areas and volumes
, Use in interior and exterior conditions.
° Easy-to-read numbers and the backlit screen are clearly visible indoors andoutdoors.
o Use the integrated bubble vial to level your tool for accurate measurement.
o Use the Recall function to recall the last 10 readings.
° The automatic power-off function turns the tool off after 5 minutes of inactivityfor increased battery life.
48298 Manual Revised_07_O225 Page 4
Fig. 1
1
2
1. LCD display- Large LCD screen with back lighting helps you to read thelarge-numeral measuring data clearly, even in dark conditions,
2, Keyboard
3. Integrated bubble vial- helps to level your laser measuring toot
4. Keys for addition, subtraction, and recall functions.
5. Laser-receiving lens - receives the reflected laser for distance determination
6, Laser-exit aperture - emits the laser dot,
7. Beeper
8. Battery compartment - for two AA batteries,
Power supply
Laser
Measuring range (typically)
Measuring accuracy (typically)
Smallest unit displayed
Automatic switch off:
Estimated battery life (use alkaline AA
batteries)
Optimum operating temperature
Technical Specifications
2 "AA" 1.5-volt batteries
FJ=635-665nm, class llla laser,maximum laser output -<2.5roW
14 50 feet (0.3-45m)
+_3/16" (_+5ram)
1/16" (1ram)
laser: 20 seconds
measuring tool: 5 minutes
Up to 5000 single measurements
32 to 104°F (0 to 40°C)
48298 Manual Revised 07-0225 Page 5
KEYBOARD FUNCTION (See Fig. 2)
Fig. 2
2
3_
5 10
Please see the Operation section of this manual for information about the follow-ing functions and computations.
1, Measure key - to take a single distance measurement,
2. Area key - activates the area-measuring mode.
3, "volume key -activates the volume-measuring mode,
4. Pythagorean Theorem key - press the key to enter the Pythagoreantheorem mode.
5o Measuring reference point- Switches the measuring reference between thefront and the rear of the tool,
6, ON!OFFiCLR key - On, Off and Clear, back to single distancemeasurement mode.
7. M\Ft key-, change units: 1/16-in_ increments, decimal units of feet, meters,and millimeters
8, RCL key - Recalls the preceding 10 measuring data.
9, Plus key - for addition of measurements, and to scroll the recalled measuringdata upwards.
10, Minus key - for subtraction of measurements, and to scroll the recalled mea-
suring data downwards,
48298 ManuaLRevised_07-0225 Page 6
LCD DISPLAY
Full battery indicator
Empty battery indicator
_ aser beam indicator
_ Area measurement
_ Volume measurement
[_ Pythagorean Theorem measurement
Indicates that the measurement is taken from the rear of the tool.
Indicates that the measurement is taken from the front of the tool.
"Your laser measuring tool is a precision instrument. Please observe the following
guidelines to ensure optimal performance.
o
0
Do not direct the laser-measuring tool towards the sun or other sources of
bright light° This may cause an Error reading or inaccurate measurements.
Do not use the laser measuring tool as a leveling tool.
Do not operate the laser measuring tool in wet, dusty, sandy, or other adverseenvironments, Such conditions may damage inner components and affect
measuring accuracy.
When the laser measuring tool is brought into a warm environment from verycold conditions, or vice versa, allow it to come to the surrounding tempera.-ture before use.
Measuring errors can occur when measuring toward colorless liquids (e.g.,water), clean glass, Styrofoam, or similar translucent or low-density materials.
High-gloss surfaces will deflect the laser beam and result in Errormeasurements.
Very bright surroundings combined with a very low reflecting surface willreduce the measuring range and accuracy,
Do not immerse the tool in water, Wipe off dirt with a damp, soft cloth. Do not
use aggressive cleaning agents or solutions. Treat the optical surfaces with
the same care that you would apply to eyeglasses or cameras,
The accuracy of the tool must be checked before use after it has beendropped or subjected to other mechanical stresses.
48298 ManuaLRevised_0743225 Page 7
TO INSTALL BATTERIES
(See Fig. 3)
This laser measuring tool
uses two ",CA" batteries (sold
separately).
't. Open the battery cover as
indicated bY the arrow on
the battery cover.
2_ Insert two new "AA "alka-
line batteries according to
the polarity indicators in
the battery compartment.
Be sure the polarity (+/-)is correct!
Fig. 3
3. Close the cover and lock it securely in place.
NOTE:
o Replace the batteries when the battery indicator shows empty.
= Remove the batteries from the measuring tool when not using it for
extended periods.
o The 2 AA batteries should match each other in brand and type.
,, Do not mix old and new batteries.
o Remove dead batteries immediately, and dispose of them according to your
local ordinance. Never dispose of batteries in fire.
TURNING THE LASER MEASURING TOOL ON AND OFF
I.
2_
3o
4_
Press the ON/OFF key to turn on the tool. The CRAFTSMAN logo will show
on the screen for one second, then it will automatically change to the single-distance measurement mode, indicating that the tool it is ready to takemeasurements.
Press the ON/OFF key for about 2 seconds to turn off the tool.
When the measuring tool is inactive for 5 minutes, it will automatically turn
off to save battery power,
When the tool is powered off, whether manually or automatically, the mea-
suring data saved in the memory will be cleared.
USING THE LASER MEASURING TOOL
Hold the tool at the point from which you want to measure. The default refer-ence setting is from the rear of the tool. By pressing the i_ key, the setting can be
changed, so that the next measurement will be taken from the "front" of the tool.
48298 ManuaLRevised_07-0225 Page 8
To change measuring reference point
_, Indicates that the measurement is computed from the position of the rear of the tool.
f_'Indicates that the measurement is computed from the position of the front of the tool.
After powering off, the reference point will automatically default back to rear.
To change the units
Press the M\Ft key to change the units among 1/16 in. increments, decimal units of
feet, meter, and millimeter after taking measurements, as shown below.
Setting Distance Area Volume
1/16 in feet & 1/16inch feet 2 feet 3
ft feet (decimal) feet 2 feet 3
m meters m 2 m 3
mm millimeters m 2 m 3
To take measurements
NOTE: The laser wil! switch off after 20 seconds of inactivity, If a measurement has
not been made within the previous 20 seconds, push MEASURE again to turn onthe laser.
A,_k WARNING: Do not point the la-ser dot at persons or animals and donot stare into the laser beam or view
directly with optical instruments.
Clear function
Push the Clear button to erase the
current measurement and display
the previous measurement.
Fig. 4
Single distance measurement
. Press the MEASURE key to turnon the laser; the laser indicator
will blink from bottom to top(see Fig. 4 & 5).
, Aim the laser at the target youwant to measure; the integratedvial can help you level your tool,
3. Press the MEASURE key againto take a measuremenL
Fig. 5
II
48298 ManuaLRevised 0743225 Page 9
4. Fig. 6
m
6_
7.
8_
g.
The length is shown in the
lower row of the screen in large
numerals, and the laser beam
switches off (Fig. 6).
To take a second measure-
ment, press the MEASURE keyto turn on the laser again, andthe first measurement data will
show in the upper row of thescreen (Fig. 7).
Aim at the new target.
Press the Measure key again totake a second measurement.
The second length is shownin the lower row of the screen,and the laser beam switches
off (Fig. 8).
To take a new measurement,
follow steps 5 through 8, above.
Fig. 7
6.765 ft
€II
6.765 ft
NOTE: If after choosing Area,Volume or Pythagorean Theoremmeasurement modes, you want to
go back to the single-measurementmode, Press the CLR key to switchback to single-measurement mode.
Area measurement
Press the "_" key to enterarea measurement mode; theblinking line in "zC'EZT" iconindicates the length to be
measured (Fig. 9).
Fig. 8
6.765 ft
2.24t ft
Fig. 9
i i i
48298 Manual Revised_07-O225 Page 10
2. Press the MEASURE key toturn on the laser beam; thelaser indicator will blink from
bottom to top (Fig. 10).
3. Position the tool to aim the
laser dot at the target to which
you want to measure°
4. Press the MEASURE key todisplay the measured length inthe upper and lower rows of thescreen (Fig. 11)_
5, The width line in the "zCC; z'' iconwill start to blink.
64
,
8_
Position the toot to aim the laser
dot at the width target.
Press the MEASURE key againto display the area in the lowerrow of the screen; the width will
be displayed at the same time in
the upper row (Fig, 12).
Press the MEASURE key to makea new measurement.
Volume measurement
I. Press the "IZ_" key to entervolume measurement mode,
The blinking line in "1_" iconindicates the length to be
measured (Fig, 13),
Fig, 10
II z?T7-_--_--_--_--_--_--_7
Fig. 11
I
&[ZB
6.762 ft
6.762 ft
Fig. 12
2,182 ft
14.755 ft
Fig. 13
48298 Manual_Revised_07,0225 Page 11
2. Fig. 14
3_
Press the MEASURE key toturn on the laser beam; thelaser indicator will blink from
bottom to top (Fig. 14).
Position the tool to aim the
laser dot at the target to which
you want to measure.
4. Press the MEASURE key todisplay the measured length in
the lower and upper rows of thescreen. The height line in the "I_" icon will also start to blink
(Fig. 15).
5. Position the tool to aim the
laser at the target.
6o Press the MEASURE key again
to display the height in the up-per row of the screen; the areawill be displayed at the sametime in the lower (Fig. 16).
7. The width line in the "_" icon
will start to blink (Fig. 16).
8_
.
Press the MEASURE key
again to display the volume inthe lower row of the screen;
the width will be displayed atthe same time in the upperrow (Fig. 17).
Press the MEASURE key tomake a new measurement.
Ii
Fig. 15
II
6.759 ft
6.759 ft
Fig. 16
oII
g 2.320 ft
15.681 ft 2
Fig. !7
3.675 ft
57.627 ft
48298 Manual Revised_07*0225 Page 3.2
Pythagorean Theorem
Measurement
1. Press the "[_:_" key to enter
Pythagorean Theorem mea _surement mode.
2_
,
The blinking line in "L_"indicates the first side length
of a right triangle that is to bemeasured (Fig. 18),
Press the MEASURE key to turnon the laser beam; the laserindicator blinks from bottom to
top (Fig. 19).
4. Position the tool to aim the laser
at the target. In this example,the tool is positioned in thelower right corner of the triangle.
5. Press the MEASURE key to dis-
play the measured length of thefirst triangle side in the lower
and upper rows of the screen(Fig. 20).
6_ The hypotenuse (diagonal) line in
"[_" will start to blink.
7_
.
9_
Without changing the toot posi-tion, aim the laser dot at the
hypotenuse target.
Press the MEASURE key againto display the calculated lengthof the third triangle side in thelower row of the screen; the
hypotenuse length wilt be dis-played at the same time in theupper row ( Fig° 2I).
Press the MEASURE key tomake a new measurement.
NOTES:
Fig. 18
Fig. 19
Fig.20
6.765 ft
6.765
Fig. 21
15.292 ft
13.714ftThe hypotenuse measurement
must be longer than the first
side measurement of a right
triangle, otherwise the LCD will display "Wrong Input" reminding you to
re-measure the hypotenuse.
48298 Manua!_Revised_07©225 Page 13
Add and subtract lengths
1. 70 measure the first length, follow steps 1 through 4 for "Single distance mea-suremenL"
2. Press the + or - key; the symbol will show below the battery indicator.
3. Press the MEASURE key to turn on the laser. The first measured data will showin the upper row of the screen.
4. Press the MEASURE key again to display the sum of the two distances in thelower row of the screen; the second measured distance will be displayed at the
same time in the upper row of the screen.
5. Follow the same method to make additional calculations.
Add and subtract area or volume
1. Take the first area or volume measurement following the instructions in "Areameasurement" or "Volume measurement."
2. Press the + or- key: the symbol wilt show below the battery indicator.
3. Take the second area or volume measurement.
4. The sum of the two areas or volumes will be displayed in the lower row of thescreen, and the second measured area/volume will be displayed at the same
time in the upper row of the screen.
5. Follow the same method to make additional calculations.
Error signals
The following error signals may appear on the screen of your tool:
Conditions too bright The surroundings are too brightly tit.
The target provides poor reflection of the
Target too dark laser; you can change to another target orcover the target with a piece of white paper°
The measuring range for this tool is fromTarget out of range i ft. to 150 ft..
The optimum operating temperature is 32Temperature too high to 104°I:.
The optimum operating temperature is 32Temperature too low to 104°F.
Low battery A reminder to replace the batteries.
You moved the tool quickly when measur-
Strong vibration ing; always keep it steady when taking ameasurement.
The hypotenuse you measured is shorter
Wrong Input than the one side length of a right triangle;re-measure.
48298 Manual_Revised 07-0225 Page 14
Save and recall measurements
This laser measuring tool automati-cally saves the last 10 measure-ments or calculations, as describedbelow. If more than 10 measure-
ments are made, the new data will
cover the preceding data.
Only single distance, area, volume,and the calculated third length of aright triangle data are saved in thememory. The length and width of thearea; the length, width, and heightof the volume; the measured side
length of a right triangle and the hy-potenuse length cannot be recalled.Neither can the calculated sum of
lengths, areas, or volumes be savedand recalled.
To recall the measurements, press
the side key "RCL": the last ten mea-surements will be displayed on thescreen (Fig. 22).
1.
1
u
Press the + key to scrollupwards (Fig. 23).
Press the - key to scroll
downwards (Fig. 24).
Press any other key exceptONiOFF/CLR, Ft/M key to goback to the preceding mea-surement mode.
Clear the current measurement
Fig. 22
RCL÷
f1
05/05
17.755 ft 257.672 ft 3
13.714 ft
Fig. 23
RCL 04/05÷
f
7.540 ft17.755 ft
57.672 ft '
Fig. 24
RCL÷
01!05
57.627 ft 3
13.714 ft10.640 ft
_-- 03f05
_- 04t05
_- 05!05
4-. 02f05
03105
•@-04fe5
04t05
'4- 05t05
_-- 01/05
1.
2.
In SINGLE-DISTANCE measuring mode: when taking a measurement, press the
CLR key to eliminate the current measuring data. Older measuring data cannot
be cleared. The cleared measuring data will not be saved in the memory; youcannot recall it later.
In AREA measuring mode, clear the current measured length by pressing theCLR key; the width and the calculated area cannot be cleared. If the widthmeasurement is incorrect, you can re-measure the length and width to getthe correct area.
3_ In VOLUME measuring mode, clear the length, the height or both of them by
pressing the CLR key after measuring them. The width and the calculatedvolume cannot be cleared. If the width measurement is incorrect, you canre-measure the length, height and width to get the correct volume.
48298 ManuaLRevised 07-0225 Page 15
4. in Pythagorean Theorem measuring mode, you can clear the measured sidelength of the right triangle by pressing the CLR key after measuring it. The hy-potenuse and the calculated side length of the right triangle cannot be cleared. Ifyou take an incorrect hypotenuse measurement, you can re-measure it.
NOTES: In Area, Volume, Pythagorean Theorem measuring mode, when all the
measurements are cleared, press the CLR key again, it will go back to single dis-
tance measurement mode°
This laser measuring tool has been designed to be a low-maintenance tool.However, in order to maintain its performance, you must always follow these
simple directions_
,, Always handle the too! with care. Treat it as an optical device, such as acamera or binoculars.
• Avoid exposing the tool to shock, continuous vibration or extreme hot or
cold temperatures.
o Always store the tool indoors. When not in use, always store the tool in its
protective case.
_, Always keep the tool free of dust and liquids. Use only a clean, soft clothfor cleaning. If necessary, slightly moisten the cloth with pure alcohol or alittle water°
,, Do not touch the lens with your fingers.
o Check the batteries regularly to avoid deterioration. Always remove the batter-ies from the tool if it is not going to be used for an extended period of time.
o Replace the batteries when the battery icon displayed on the screen is con-
tinuously empty.
,, Do not disassemble the laser measuring toot; this will expose the user to
hazardous radiation exposure.
Do not attempt to change any part of the laser lens.
48298 ManuaLRevised_07-9225 Page 16
PROBLEM CAUSE
U
Tool cannotswitched on
LCD displays" Lowbattery"
SOLUTION
Reinstall the batteries
according to the polarity
indicators in the batterycompartment
Replaced with new bat-teries
LCD displays "Con-ditions too bright"
LCD displays "Tar+`get too dark"
o Batteries are installed
incorrectly
,, Batteries are low
..... voltage ........
Batteries are depleted
The ambient light is toobright
The target does not ad+
equately reflect the laser
• The measurement
exceeds the measuringrange of the tool
LCD displays "Tar-get out of range" D The target surface re-
flects too intensely (e.g,a mirror) or insufficiently(e.g, black fabric).
LCD displays "Tem-Too high temperature
perature too high"
LCD displays "Tem-perature too low"
LCD displays
"Wrong Input"
LCD displays
"Strong vibration"
Too low temperature
Insert new batteries
Change the condition andre+measure
Change the measuring tar-get or cover it with a pieceof white paper
Take measurement '
within the range of 1footto 150 foot,
,, Change the measuringtarget or cover it with apiece of white paper onthe target,
..... .......................... ++
Wait until the measur-
ing toot has reached theoperating temperature (32
to +104°F)
Wait until the measur-
ing tool has reached theoperating temperature (32to 104°F)
Hypotenuse you measuredis shorter than the one side
length of a right triangle
You moved the tool quickly
when taking a measure-ment
Re-measure to keep hy-potenuse longer than thefirst side length of a right
triangle.
Always keep the toolsteady when taking a mea-surement
48298 ManuaLRevised_07-0225 Page 17
48298ManuaLRevised07-0225 Page18
48298ManualRevised07-0225 Page19
Get,it fixed, at yourhome or ours.
Your Home
For expert troubleshooting and home solutions advice:
manage homewww,managemyhome.com
For repair - in your home - of all major brand appliances,lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories andowner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliancesand items like garage door openers and water heaters.
1-800-4-MY-HOME ® calf anytime, day or night
(1-800-469 _4663) (U,S,A, and Canada)www.sears.com www.sears.ca
......................................................................................................................................... .......................... =................
Our Home
For repair of carry-in items like vacuums, lawn equipment,and electronics, call anytime for the location of the nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S,A.) 1-800-469-4663 (Canada)www.sears,com www.sears,ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (usA,) 1-800-361-6665 (Canada)
Para pedir servicio de reparaci6n Au Canada pour service en frangais:a domicilio, y para ordenar piezas: 1-800-LE-FOYER Mc
1-888-SU-HOGAR® (1-800-533-6937)(1-888-784-6427) www .sears .ca
Seal,, s
©SearsBrands,LLC
® Registered Trademark 1TMTrademark / sMSe_ice Mark of Sears Brands, LLC® Marca Registrada I TM Marca de F&brica / s_ Marca de Servicio de Sears Brands, LLC_c Marque de commerce / MDMarque d_pos_e de Sears Brands, LLC
Manual de Producto
Herramienta de Nledici6n L_ser
Modelo N ° 320.48298
iPRECAUCION! Antes deutilizar este producto, lea elpresente manual y siga todassus Instrucciones de Seguri-dad y de Operacibn.
• instrucciones de seguridad
• Operaci6n• Mantenimiento
o Detecci6n de problemas
Sears, Roebuck and Co., Hoffman Estates, IL 60179www, craftsman,com
Garantia P_gina 2
Precauciones de seguridad P_,ginas 3-4
Descripci6n Pb,ginas 4-7
Operaci6n P&ginas 7-16
Mantenimiento P&gina 17
Detecci6n de errores P&gina 17
GARANTiA COMPLETA DE UN AI_O SOBRE ESTE PRODUCTO
CRAFTSMAN®
Siesta herramienta Craftsman no Io satisficiera por completo dentro del
a_o de la adquisiciSn, devuelvato a la tienda Sears m&s cercana o a otro
distribuidor Craftsman en los Estados Unidos para obtener un reemptazo
gratuitoo
Esta garantia tendr& una vigencia de s61o 90 dias a partir de la fecha deadquisici6n sieste producto se usa con fines comerciales o de atquiler,
Este garantia le otorga derechos legales especificos y usted puede contarcon otros derechos, que pueden variar de estado a estado.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
iGUARDE ESTAS INSTRUCCIONES!
iLEA TODAS LAS INSTRUCCIONES!
CONTENliDOS Y ACCESORIOS
Herramienta de medici6n t_ser, estuche de transporteo
48298 ManuaLRavised 07-0225 Page 2
,_ ADVERTENClA: ASEGORESE de leer y comprender todas las instrucciones
del presente manual antes de utilizar este producto. No seguir estasinstrucciones puede generar una peligrosa exposiciSn ala radiaci6n, unadescarga el6ctrica y/o lesiones corporales.
PRECAUOION: NO INTENTE modificar el desempefio de este dispositivo
Ihser de cualquier mode, Esto puede provocar una petigrosa exposiciSn aradiaciSn I_ser.
_k ADVERTENCIA: LUZ DE LASER. RADIACION DE LASER. Evite la
exposiciSn ocular directa. NO mire hacia este haz de luz. Encienda el haz delhser sSlo cuando utilice esta herramienta. Lhser clase Itla.
,_ ADVERTENOIA: El use de controles o ajustes o el desempeSo de
procedimientos distintos a los especificados en este manual pueden generarpeligrosas exposiciones a ta radiaci6n Ihser_
,_k ADVERTENCtA: El use de instrumentos 6pticos tales come telescopios u
otros objetos de tr&nsito, pero sin limitarse a ellos, para vet el haz en abanicode l&ser incrementar_, el peligro ocular. Esta herramienta de medici6n cuentacon una luz de I&ser incorporada. E! Ihser es de Clase ilia y emite una salida
m&xima de potencia de 2.5roW y longitud de onda de 635-665nm. EstosIhsers normalmente no presentan un peligro 6ptico_ Sin embarqo, NO MIREdirectamente al haz, porque esto puede provocar ceguera .......
i, :Avom EXl,0SUREtemporal.
La siguiente etiqueta aparece en su herramienta de mediciSnI_,ser. lndica la ubicaciSn desde la cual ta herramienta de
mediciSn I&ser emite la luz de Ihser. Tonga presente laubicaciSn de la tuz de I&ser cuando utiliza ta herramienta.
Siempre cerciSrese de que las personas que est6n alrededordel hrea donde va a user la herramienta est6n conscientes de
los peligros a los que se exponen si miran directamente haciael f&ser.
o No quite o modifique ninguna etiqueta del producto.
- Evite la exposicibn ocular directa. El haz de l&serpuede provocar ceguera temporal.
• El I_ser de la herramienta de medici6n laser no es un
juguete. Siempre mant6ngalo fuera del alcance de los
nifios. La luz de l#,ser emitida per este dispositivo nuncadebe dirigirse hacia cuatquier persona per ninguna razSn.
No manipule la herramienta cerca de los nifios ni
permita que manipulen la herramienta.
No coloque la herramienta en una posiciSn en la que alguien pueda mirardirectamente hacia el haz de Ihser, ya sea en forma intencional o nointenciona!.
48298 Manuaf Revised 07-0225 Page 3
o No Io utilice en superficies tales como acero en laminas que tienen
superficies brillantes o reflectivas. La superficie briltante puede reflejar el
haz de w_elta al operadoro
= Siempre apague la herramienta si no la est_ usando. Dejar la herramienta
encendida aumenta et desgo de que alguien mire involuntariamente el haz enabanico de laser,
o No intente modificar el desempe5o de este dispositivo laser de cualquier
modo. Esto puede provocar una peligrosa exposici6n a radiaci6n laser.
,, No intente reparar o desarmar la herramienta de medici6n laser. Si personasno calificadas intentan reparar este producto, pueden provocarse lesiones
graves. Todas las reparaciones efectuadas a este producto deben reatizarlass61o personal de servicio autorizadas.
No utilice ta herramienta en Areas combustibles, como en la presencia de
liquidos inflamabtes, gases o polvillo.
• Utitizar accesorios que hart sido disefiados para usar con otras herramientasde laser podria ocasionar graves lesiones.
= Mantenga las baterias alejadas de los niSos,
o Para mrs informaci6n en relaciSn a los lasers, consultar ANSI-Z136.1, la
Norma para el uso seguro de lasers disponible en el Instituto del LAser deEE. UUo (,407) 380-1553.
CONOZCA SU HERRAMtENTA DE MEDICION LASER (Ver Fig. 1)
La herramienta de mediciSn I_ser es una herramienta de alta precisiSn para una
operaci6n r&pida y f&cil:
= Mide distancias desde I pie hasta 150 pies con una precisiSn de ±3/16
pulgada.
= La herramienta de medici6n laser se utiliza para:
• Medir distancias, longitudes, alturas y espacios fibres.
= Situaciones dificiles de medir: Et modo de Teorema de Pit&goras permiteuna medici6n indirecta.
• Calcular Areas y volumenes,
• Usarse en el interior yen el exterior.
• Los n_meros f&ciles de leer y la pantalla retroiluminada son f&cilmentevisibles en el interior o exterior.
° Usar la ampolleta de burbujas integrada para nivelar su herramienta para una
mediciSn precisa.
• Usar la funciSn Memoria para recordar las t'_ttimas 10 mediciones.
= La funciSn de apagado automAtico apaga la herramienta despu6s de 5minutos de inactividad para prolongar ia vida de ias baterias,
48298 Manuat__Revised_07-0225 Page 4
Fig. 1
I. Pantalta LCD: La gran pantalla de LCD con retroiluminaci6n Io ayuda a
leer claramente la informaci6n de medicidn con grandes n0meros, inclusoen ia oscuridad.
2o Teclado_
3. Ampolteta de burbujas integrada: Ayuda a nivelar su herramienta demedici6n Ifiser.
4o Teclas para funciones de suma, testa y memoria,
5_ Lente receptora de Iflser: Recibe el !riser reflejado para determinar distancias.
6. Apertura de salida del Iflser: Emite el punto de Iflser.
Alerta sonora.
8o Compartimiento de baterias: Para dos baterias AA.
Especificaciones T_cnicas
Fuente de energia
Lflser
Rango de medici6n (tipicamente)
Precisi6n de medici6n (tipicamente)
Unidad mils pequeSa mostrada
Apagado automfltico:
Duraci6n estimada de baterfas (uso Hasta 5000 mediciones _nicasde baterias alcalinas AA)
Temperatura de funcionamiento 6ptima 32 a 104°F (0 a 40°0)
48298 ManuaLRevised__07*0225 Page 5
2 baterias "AA" de 1 o5voltios
B=635-665nm, I&ser clase Ilia,
salida m_xima de potencia de < 2.5mW
1-150 pies (0.3-45m)
±3/16" (±5mm)
1/16" (1ram)
Lflser: 20 segundosHerramienta de medici6n: 5 minutos
UNClON DE TECLADO (See Fig. 2)
Fig. 2
2
3_
5 10
Por favor, ver la secciSn de Operaci6n de este manual para informaciSn sobrelas siguientes funciones y c6mputos.
1, Tecla de medici6n: Para tomar una medici6n t]nica de distancia.
2. Tecla de _rea: Activa el modo de mediciSn de &rea.
as
4.
5_
6_
Tecla de volumen: Activa el modo de medici6n de volumen.
Tecta de Teorema de Pit&goras: Presione la tecla para ingresar el modo de
teorema de Pit&goras.
Punto de referencia de medici6n: Cambia la referencia de medici6n entre la
parte frontal y trasera de la herramientao
Teclas ON/OFF!CLR (encendido/apagado/borrar): Encendido, apagado y
borrar, de vuelta al modo de medici6n de distancia unica.
7. Tecla M\Ft: Cambia unidades: Incrementos de 1/16 pulgadas, unidades
decimales de pies, metros y milimetros.
8. Tecla RCL (memoria): Recuerda los Qltimos 10 datos de medici6n.
9. Tecla Plus (suma): para sumar mediciones y para poder visualizar los ultimosdatos de medici6n en forma ascendenteo
t 0. Tecla Minus (resta): para restar mediciones y para poder visualizar losL]ttimos datos de medici6n en forma descendente.
48298 ManuaLRevised_07-0225 Page 6
PANTALLA DE LClD
Indicador de bateria Ilena
tndicador de bateria vacia
& Indica que la medici6n se toma desde la parte trasera de la herramienta.
indica que la medici6n se toma desde la parte frontal de la herramienta.
indicador de haz de laser
Medici6n de Area
Medici6n de volumen
Medici6n de Teorema de PitAgoras
Su herramienta de medici6n laser es un instrumento de precisi6n. Tenga a bien
cumplir con tas siguientes guias para garantizar un desempeSo 6ptimoo
o No dirija la herramienta de medici6n l_ser hacia el sol u otras fuentes de luces
brillantes. Esto puede provocar una lectura err6nea o mediciones imprecisas.
o No utilice la herramienta de medici6n laser como una herramienta de nivelaci6n.
• No utitice la herramienta de medici6n laser en medios hOmedos,
polvorientos, arenosos u otros medios adversos, Tales condiciones puedendaSar los componentes internos y afectar ia precisi6n de la medici6no
o Cuando la herramienta de medici6n laser se Ileva a un medio c#.lido de
condiciones muy frias, o viceversa, permita que se adapten a la temperaturaambiente antes del uso.
Pueden ocurrir errores de medici6n cuando se mida hacia liquidos
transparentes (por ej., agua), vidrio transparente, espuma de poliestireno o
materiales translucidos simitares o de baja densidad.
o Las superficies de alto bri!lo desvian el haz de laser provocan mediciones err6neas.
o Los medios muy brillantes combinados con una superficie de reflexi6n muy
baja reducen el rango de medici6n y la precisi6n.
, No sumerja la herramienta en agua. Limpie el polvillo con un pa5o suave ht]medo.No use agentes o sofuciones de limpieza agresivos. Trate las superficies 6pticascon el mismo cuidado que aplica a los anteojos o las c_maras.
Debe verificarse la precisi6n de la herramienta antes de su uso despu_s de
que haya sufrido una caida u otra tensi6n mec&nica.
48298 ManuaLRevised_07-0225 Page 7
PARA INSTALAR LASBATERIAS ever Fig. 3)
Esta herramienta de medici6nl_ser utiliza dos baterias "/_Jk"
(en venta por separado).
1.
2,
3,
Fig, 3
Abra ta tapa delcompartimiento debaterias como Io indica la
flecha de la tapa.
Introduzca dos baterias
atcalinas nuevas "AA"
segC_nlos indicadores
de polaridad delcompartimiento de hater[as, iVerifique que la polaridad (+/-) sea la correcta!
Cierre ta tapa y ajOstela en su lugar.
NOTA"
o Cambie las baterias cuando el indicador de baterias muestra "vacio".
= Cambie las baterias de la herramienta de medici6n cuando no la use por
periodos prolongados.
o Las dos baterias AA deben ser iguales en cuanto a marca y clase.
o No mezcle baterias usadas con nuevas.
o Quite las baterJas usadas de inmediato, y eliminelas de acuerdo con las
ordenanzas locales, Nunca las tire al fuego.
COMO APAGAR Y ENCENDER LA HERRAMIENTA DE MEDICION LASER
1. Presione la tecla ON/OFF (encendido/apagado) para encender laherramienta. El logo de CRAFTSMAN aparecer_ en la pantalfa durante
un segundo, luego cambiarb, autom&ticamente al modo de medici6n dedistancia Onica, indicando que ta herramienta estb, lista para tomar medidas.
2. Presione la tecla ON/OFF (encendido/apagado) durante 2 segundos para
apagar la herramienta.
3. Cuando la herramienta de medici6n est& inactiva durante 5 minutos, se
apagar& de manera autom&tica para ahorrar energia de bateria.
4. Cuando se apaga la herramienta, ya sea de manera manual o autom&tica, lainformaci6n de medici6n guardada en la memoria se borrar&.
COMO USAR LA HERRAMIENTA DE MEDICION LASER
Sostenga ia herramienta en el punto desde el cual desea tomar una medici6n,La configuraci6n de referencia por defecto es desde la parte trasera de laherramienta. AI presionar la tecla, puede modificarse la configuraci6n, para que
la pr6xima medici6n se tome desde el "frente" de la herramienta,
48298 Manual_Revised_07-0225 Page 8
Para cambiar el punto de referencia de medicibn
Indica que ta medici6n se computa desde la posici6n de la parte trasera dela herramienta.
Indica que la medici6n se computa desde la posici6n del frente de la herramienta.
Despu6s de apagar, el punto de referencia volverA de manera autom&tica por
defecto a la parte trasera.
Para cambiar las unidades
Presione la tecta Ft/M para cambiar las unidades con incrementos de 1/16pulgadas, unidades decimales de pies, metros y mil[metros despu6s de tomar
medidas, como puede verse a continuaci6n:
Configuraci6n Distancia Area Volumen
t/16 pulg, Pies y 1/16 pulg, Pies 2 Pies a
pies Pies (decimal) Pies 2 Pies _
m. metros m 2 m3
mm, milimetros m 2 m3
Para tomar medidas
NOTA" El laser se apagar_, despu6s de 20 segundos de inactividad. Si famedici6n no se ha realizado dentro de los 20 segundos previos, presione
MEASURE (medida) de nuevo para Fig, 4encender el IAsen
ADVERTENCIA," No apunte elpunto de laser hacia personaso animales y no mire al haz delb,ser o visualice directamente con
instrumentos 6pticos.
Funci6n de borrado
Presione el bot6n Clear (borrar)para eliminar la medici6n actual yvisualizar la medici6n previa.
Medici6n de distancia t]nica
1.
2_
Presione ta tecla MEASURE paraencender el laser; el indicadordel laser destellar& de abajo
hacia arriba (ver Fig, 4 y 5).
Apunte et l&ser al objetivo quedesea medir; la ampolleta
integrada puede ayudarlo anivelar la herramienta,
Fig, 5
!!
48298 Manual_Revised_07-0225 Page 9
3. Fig. 6
1
Presione ta tecla MEASURE
para tomar una medida.
La tongitud se visualiza en la
hilera inferior de la pantalla en
ndJmeros grandes, y el haz de
Ib,ser se apaga (Fig. 6).
5. Para tomar una segunda
medici6n, presione la tecla
MEASURE para encender et
i&ser de nuevo, y la informaci6n
de la primera medici6n
aparecer& en la hilera superior
de la pantalla (Fig. 7).
6. Apunte al nuevo objetivo.
7. Presione la tecla Measure de
nuevo para tomar una segundamedida.
°
w
La segunda longitud sevisualiza en la hilera inferior de
la pantatla, y el haz de I&ser seapaga (Fig. 8).
Para tomar una nueva
medicidn, siga los pasos de 5 a8, mencionados antes.
NOTA; Si despu6s de elegir losmodos de mediciSn de Area,
Votumen o Teorema de Pit&gorasdesea volver al modo de medici6n
unica, presione la tecla CLR paravotver al modo de medici6n _nica.
Medici6n de _rea
Presione la tecla "z_'" para
ingresar el modo de medici6n;la linea deste!lante del icono"
"indica la Iongitud que se
va a medir (Fig. 9).
6.765 ft
Fig. 7
i1
[]1
6.765 ft
Fig. 8
6.765 ft
2.241 ft
Fig. 9
zITT7
48298 Manual Revised_074)225 Page 10
2. Fig, 10
3_
Presione la tecla MEASURE
para encender el haz de laser;el indicador del laser destetlarA
de abajo hacia arriba (Fig. 10).
Coloque la herramienta paraapuntar el punto de laser en elobjetivo sobre el que se desearealizar una medici6n,
4. Presione la tecla MEASURE
para visualizar la Iongitudmedida en las hileras
superiores e inferiores de lapantalta (Fig° 1I),
5. La linea de ancho en el icono",d:Z:::7"comenzar& a destellar.
,
7_
.
Coloque la herramienta paraapuntar el punto de laser en elobjetivo de ancho.
Presione de nuevo ia tecla
MEASURE para visualizar el_.rea en la hilera inferior de
la pantalla; et ancho podrb.visualizarse al mismo tiempo en
la hilera superior (Fig. 12).
Presione la tecta MEASURE
para tomar una nueva medida,
Medici6n de volumen
Presione la tecla "1£_" para
ingresar el modo de medici6nde volumen, La linea destellante
en el icono "f_" indica la
Iongitud a medirse (Fig. 13)o
oII
g
Fig. 11
l
6.762 ft
6.762
Fig. 12
2.182 ft
14.755 ft
Fig. 13
48298 ManuaLRevised 07-0225 Page 11
2. Fig. 14
3,
.
5_
6_
7_
8_
9_
Presione la tecla MEASURE
para encender el haz de tAser;el indicador det Dser destellarA
de abajo hacia arriba (Fig. 14).
Coloque la herramienta para
apuntar el punto de laser en el
objetivo sobre el que se desearealizar una medici6n.
Presione la tecla MEASURE
para visualizar la Iongitudmedida en las hileras
superiores e inferiores de la
pantalla. La linea de ancho enel icono "i_" comenzarA a
destellar (Fig. t5).
Coloque la herramienta para
apuntar el punto de laser en
el objetivo.
Presione de nuevo la tecla
MEASURE para visualizar el&rea en la hilera inferior de
la pantalla; el ancho podr&visualizarse al mismo tiempo enla hilera superior (Fig, 16),
La linea de ancho en elicono "(_" comenzarb, a
destellar (Fig. 16).
Presione de nuevo la tecla
MEASURE para visualizar elvolumen en la hilera inferior
de la pantalla; el ancho podr&visualizarse al mismo tiempo en
la hilera superior (Fig, 17).
Presione la tecla MEASURE
para tomar una nueva medida.
II
Fig. 15
!i
6,759 ft
6.759 ft
Fig, 16
oII
Fig. 17
3.675 ft
57.627 ft 3
48298 Manual__Revised_07©225 Page 12
Medicibn de Teorema de Pitbgoras
En lugares dificiles de alcanzar, usted puede usar el Teorema de PitAgoras paradeterminar una medici6n de manera indirecta. Mida la longitud del primer lado del
tri&ngulo rect_ngulo y la hipotenusa (lado diagonal) del tri_nguto rect&ngulo, y laherramienta de medici6n autom&ticamente catcular_ el segundo lado del tri&ngulo.
24
an
Presione la tecla "L::_" para ingresar el modo de medici6n de Teorema
de Pit&goras.
La linea destellante en"L:_"
indica la Iongitud del primer tado
de un triAngulo rect&ngulo que vaa medirse (Fig. 18)
Presione la tecla MEASURE
para encender el haz de laser;el indicador del laser destella
de abajo hacia arriba (Fig. 19),
Fig. 18
4_
m
6_
7_
Coloque la herramienta para
apuntar el punto de I_.ser en el
objetivo° Utilice la ampo!leta
det nivel para garantizar queesta medici6n est6 Io m&s
horizontal posibleo En este
ejemplo, ta herramienta secoloca en el extremo derecho
inferior del triAngulo.
Presione la tecla MEASURE
para visualizar la Iongitud
medida del primer lado
del triAngulo en las hileras
superiores e inferiores de la
pantalla (Fig. 20).
La tinea de la hipotenusa
(diagonal) en "_--_" comenzar#,a destellar.
Sin cambiar la posici6n dela herramienta, apunte elpunto de laser en el objetivo
de la hipotenusa.
Fig. 19
Fig, 20
[]:
6.765 ft
6.765 ft
48298 ManuahRevised 07-0225 Page 13
8. Fig. 21
,
Presione de nuevo la tecla
MEASURE para visualizar laIongitud calculada del tercerlado del tri&ngulo en la hilerainferior de la pantalla; la
Iongitud de la hipotenusa podr&visualizarse al mismo tiempo en
la hilera superior (Fig. 21).
Presione la tecla MEASURE
para tomar una nueva medida.
15.292 ft
13o714ft
NOTAS: La medici6n de la hipotenusa debe ser m&s larga que la medici6n del
primer lado del tri&ngulo rect&ngulo, de otro modo la pantalla de LCD mostrarb,
"ingreso incorrecto", record&ndole que vuelva a medir la hipotenusa. Cuando
tome dos medidas, verifique que est6n tomadas desde el mismo punto de
inicio y la primer a medici6n sea perpendicular al objetivoo Tomar las medidas
correctamente ayudar_ a obtener la distancia calculada m_s precisa.
Sumar y restar longitudes
1. Para medir la primera Iongitud, siga los pasos de 1 a 4 para "medici6n dedistancia t_nica".
=
3_
4,
Presione la tecla + o - ; el simbolo mostrar& el indicador de bateria en la
parte inferior.
Presione la tecla MEASURE para encender el I&ser. La informaci6n que sehaya tornado primero aparecer_, en ta hilera superior de la pantallao
Presione de nuevo la tecla MEASURE para visualizar la suma de las dos
distancias en la hilera inferior de la pantalia; la segunda distancia medidapodr& visualizarse al mismo tiempo en la hilera superior de la pantalla.
5. Siga el mismo m6todo para realizar c_lculos adicionales,
Sumar y restar &rea o volumen
1. Tome la primera mediciSn de &rea o volumen siguiendo las instrucciones de"Medici6n de &rea" o "Medici6n de volumen".
2. Presione la tecla + o -: El simbolo aparecerb, debajo del indicador de bateria.
3. Tome la segunda medici6n de &rea o voiumem
4. La suma de las dos &reas o voh_menes podrA verse en la hilera inferior dela pantalla, y la segunda medici6n de &rea/volumen podr& verse al mismotiempo en la hilera superior de la pantalla,
5, Siga el mismo m6todo para realizar cAiculos adicionales.
48298 ManuaI Revised_074-)225 Page !4
Sefiales de error
Las siguientes sefiales de error pueden aparecer en la pantalla de su herramienta:
0 Condiciones muy brUlantes Los alrededores est6n demasiado iluminados.
00bjetivo demasiado oscuro
00bjetivo fuera de alcance
8 Temperatura demasiadoelevada
Temperatura demasiado baja
D Bateria baja
Vibraci6n fuerte
Ingreso err6neo
El objetivo ofrece una reflexi6n pobre
det I&ser; usted puede cambiar a otroobjetivo o cubrir el objetivo con unpedazo de papel blanco.
El rango de medici6n de esta herramientaes de 1 pie a 150 pies.
La temperatura 6ptima de funcionamientoes de 32 a 104°Fo
La temperatura 6ptima de funcionamientoes de 32 a 104°R
Un recordatorio para cambiar las baterias,
Usted movi6 la herramienta r_.pidamente
cuando reatizaba la medici6n; siempre
mant_ngala firme cuando tome mediciones.
La hipotenusa que midi6 es m&s corta
que la iongitud de un lado del tri&ngulorect&ngulo; vuelva a medir.
Guarde y recuerde mediciones
Esta herramienta de medici6n I_.ser automAticamente guarda las ultimas 10mediciones o c#,fculos, como se describe a continuaci6n. Si se realizan m&s de
10 mediciones, la nueva informaci6n cubrirA la informaci6n anterior°
S6to se guardan en la memoria distancia Onica, Area, volumen y ta terceraIongitud calculada del tri&ngulo rect&ngulo. No pueden volver a verse la Iongitud
y ancho del _rea, la Iongitud, ancho y alto del volumen, la longitud de ladomedida del tri&ngulo rect&ngulo y la Iongitud de hipotenusa. Tampoco pueden
guardarse y recordarse la suma calculada de las longitudes, &reas o volomenes,
48298 ManuaLRevised 07-0225 Page 15
Para volver aver las mediciones,presione ta tecla lateral "RCL": Last31timas diez mediciones podrb, nverse en la panta!ta (Fig. 22).
!. Presione la tecla + para
ascender (Fig. 23).
2. Presione la tecla - paradescender (Fig_ 24).
= Presione cualquier teclaexcepto ONiOFF!CLR yFt!M para volver at modo demedici6n anterior°
C6mo borrar la medici6n actual
= En el modo de medici6n deDISTANCIA 0NICA: Cuando
tome una medici6n, presionela tecla CLR para borrar lainformaci6n de medici6nactual. La informaci6n de
medici6n m&s antigua nopuede borrarse. La informaci6nde medici6n borrada no se
guardar_, en la memoria; usted
no podrb, volver a verla.
2_
Fig. 22
RCL 05f054-
t
17.755 ft 257.672 ft 3
13.714 ft
<- 03105
_, 04105
•'- 05105
Fig. 23
ROt_4-
f
04f05
i,,ll,l,,i,iiJ
Fig° 24
01105
7.540 ft17.755 ft2
57.672 ft '
•"- 02105
<- 03t05
<-- 04105
En el modo de medici6n
de AREA, borre la Iongitud
medida actual presionando latecla CLR; el ancho y el &reacalculada no pueden borrarse.Si la medici6n de ancho es
incorrecta, usted puede volver
RCL÷
f
1
57.627 ft '
13.714 ft
.640 ft
,<- o4105
4- 05105
<-. 01105
a medir la fongitud del ancho para obtener el _rea correcta.
3. En el modo de medici6n de VOLUMEN, borre la Iongitud, la altura o ambos
presionando la tecla CLR despu6s de medirtos. El ancho y el volumen calculadosno pueden borrarseo Si la medici6n de ancho es incorrecta, usted puede volver amedir la iongitud, la altura y el ancho para obtener el volumen correcto.
4. En el modo de medici6n de Teorema de Pit&goras, usted puede borrar
la iongitud del lado medido del tri&ngulo rect&ngulo presionando la teclaCLR despu6s de medirla. La hipotenusa y la longitud del lado calculadodel tri&ngulo rect&ngulo no pueden borrarse. Si toma una medici6n dehipotenusa incorrecta, usted puede votver a medirla.
NOTAS; En et modo de medici6n de Area, Volumen, Teorema de Pit&goras,
cuando todas tas mediciones se han borrado, presione de nuevo la tecla CLR,volver& al modo de medici6n de distancia unica.
48298 ManuaLRevised 07-0225 Page 16
Esta herramienta de medicidn laser ha sido diseSada para ser una herramienta
de bajo mantenimiento, Sin embargo, para mantener su funcionamiento, usted
debe siempre seguir tas siguientes instrucciones.
o Siempre manipule la herramienta con cuidadoo Trate la herramienta como si
fuera un aparato 6ptico, como una c_,mara o binoculareso
o Evite exponer la herramienta a cualquier impacto, vibraci6n continua o
temperaturas extremas, ya sean de calor o de frio.
o Siempre guarde la herramienta bajo techo, Cuando no la use, siempre
guarde la herramienta en su estuche protector.
. Siempre conserve la herramienta libre de polvo o liquidos. Utilice un paso
limpio y suave para limpiar. Si fuera necesario, humedezca el paRo con
alcohol puro o un poco de agua.
o No toque la lente con sus dedos.
o Revise las baterias regularmente para evitar que se deterioren, Siempre quite
las baterias de la herramienta si no va a usarla por periodos prolongadoso
° Cambie las baterias cuando el icono de baterias mostrado en la pantalla est6 vacio,
• No desarrne la herramienta de medici6n I&ser; esto expondr& al usuario a
radiaci6n peligrosao
o No intente cambiar ninguna de tas partes del lente l_ser,
48298 Manual_Revised_07_0225 Page 17
PROBLEMA
@
La herramienta no
puede encenderse •
LapantalladeLCD Las baterias est&nmue,o_'a"Bateria baja" descargadas
La pantalta de LCDmuestra "Condicio-
nes muy brillantes, ...........
La pantaila de LCDmuestra "objetivo
muy oscuro"
La pantalta de LCDmuestra "Objetivo ofuera de alcance"
La pantalla de LCDmuestra "tempera_tura muy eievada"
La pantalla de LCDmuestra "tempera-
tura muy baja"
La pantalla de LCDmuestra "Ingresoincorrecto"
CAUSA
@
Las baterias est6n real
instaladas.
Las baterias tienen
bajo voltaje o
La luz ambiente es demasi-ado britlante
El objetivo no refleja el I&serde manera adecuada
• La medici6n supera el
tango de medici6n de laherramienta.
La superficie objetivo serefleja muy intensamente(ej. un espejo) o insufici-entemente (ej., tela negra)o
Temperatura muy elevada
Temperatura muy baja
La hipotenusa que midi6es m&s corta que lalongitud de un lado de untri&ngulo rect&ngulo.
SOLUCa6N
Reinstate tas baterias
segt_n el indicador depolaridad del Compar-timiento de baterias
Coloque baterias nuevas
Introduzca nuevas baterias
Cambie la condici6n yvuelva a medir.
Cambie el objetivo demedici6n o cQbralo con un
pedazo de papet blanco.
° Tome la medici6n den-
tro del rango de 1 pie a150 pies.
, Cambie el objetivo demedici6n o cQbralo
con un pedazo depapel blanco.
Espere hasta que la her-ramienta de medici6n haya
alcanzado la temperatura deoperaci6n de (32 a 104°F)
Espere hasta que la her-ramienta de medici6n haya
alcanzado la temperatura deoperaci6n de (32 a 104°F)
Vuelva a medir para man-tener la hipotenusa m_slarga que la longitud del
primer lado de un trib,n-gulo rect&ngulo.
Siempre mantenga la herra-mienta firme cuando tomeuna medici6n
La pantalla de LCD Movi6 la herramienta r_pi-muestra "Vibraci6n damente cuando tomaba la
fuerte" medici6n
48298 ManuaLRevised_07-0225 Page 18
48298ManualRevised_07©225 Page!9
Get:it fixed, at your home or our!!
For repair - in your home - of all major brand appliances,lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories andowner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliancesand items like garage door openers and water heaters.
1-800-4-MY-HOME® ca, anytime, day or night
(1-800-469-4663) (U,S_A. and Canada)www.sears.com www.sears,ca
Our HomeFor repair of carry-in items like vacuums, lawn equipment,and electronics, call anytime for the location of the nearest
Sears Parts & Repair Service Center
1-800-486-1222 (US.A,) 1-800-469-4663 (Canada)www.sears.com www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (u.sAo) 1-600-361-6665 (Canada)
Para pedir servicio de reparaciSna domicilio, y para ordenar piezas:
1-888-SU-HOGAR®(1-888-784-6427)
Au Canada pour service en fran(;ais:1.800-LE-FOYER Mc
(1-800-533.8937)www,sears.ca
Sears
© Seats Brary_, LLC
® Registered Trademark / T_Trademark / sMService Mark of Sears Brands, LLC® Marca Registrada i'rM Marca de F&brica t sMMarca de Servicio de Sears Brands, LLC
MDMCMarque de commerce t Marque d_pos6e de Sears Brands, LLC