jsp_plist_10_head
DESCRIPTION
NB Important to note that LD or “Lateral Deformation” test under EN397 does NOT give any guarantee or benchmarked protection against side impacts. TEST AREA TEST AREA The same weight is then dropped from just over 1 metre onto the shell at any angle between 15° and 60° for Side Impact performance (50Joules). 1KG at 2M 19JO Helmet is hit twice, once in the crown area with a 1kg chisel-shaped striker from 2.5 metres (25Joules). 2.b 2.b 2.a 2.a 1.b 1.b 1.a 1.a 2 1KG at 2.5M 25JOULES 50mm 1TRANSCRIPT
HEAD PROTECTION - MK8 EVOLUTION® HELMET
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
Mk8 EVOLUTION®
THE STRONGEST INDUSTRIAL SAFETY HELMET IN THE WORLD
EN14052 Vs EN397The EVO8™ Safety Helmet is tested from more than double the
height of helmets that meet EN397. EN14052 also requires the same
helmet to be tested twice, once on the crown and once for side
impacts. Together with testing from heights of up to 2.5 metres,
passing EN14052 means the Mk8 Evolution® can take over 3 times
the impact of any other EN397 helmet on the market. However, the
EVO8™ doesn’t just meet the new EN14052 standard, it exceeds it.
No other safety helmet offers this level of protection.
JSP has designed this product to save lives.
If you are serious about safety, you
will wear the JSP EVO8™.
NEW
PENETRATION TESTHelmet is hit once by a 3kg
conical striker from a height
of 1 metre in a 50mm radius
of the crown (29Joules).
IMPACT TEST Helmet is hit once directly
onto the crown with a 5kg
weight from 1 metre (49Joules).
360°
5KG at 1M
50JOULES
1KG at 2M
19JOULES
1KG at 2.5M25JOULES
60°
60°
5KG at 2M100JOULES
360°
50mm
50mm
5KG at 1M49JOULES
3KG at 1M29JOULES
NB Important to note that LD or
“Lateral Deformation” test under EN397 does NOT
give any guarantee or benchmarked protection against side impacts.
EN14052TESTING
1.a
1
2
EN397 TESTING
RIGH
TS RESERVED
DESIGN REGISTERED
1
2
PENETRATIONTEST - CROWNHelmet is hit twice, once in the crown
area with a 1kg chisel-shaped striker from 2.5 metres (25Joules).
PENETRATION TEST - SIDEThe same weight is then dropped from 2 metres onto the shell at any
angle between 15° and 60° for Side Impact performance (19Joules).
IMPACT TEST - CROWNHelmet is hit twice, once in an area within a 35mm radius of the
crown with a 5kg weight from just over 2 metres (100Joules).
IMPACT TEST - SIDEThe same weight is then dropped from just over 1 metre onto
the shell at any angle between 15° and 60° for Side Impact
performance (50Joules).
1.b
2.a
2.b
1.a
1.b
2.a
2.b
TESTAREA
TESTAREA
WE HAVE EVOLVED HEAD PROTECTIONThe Mk8 Evolution® is the only industrial safety helmet in the world meeting
and exceeding the new far tougher head protection standard EN14052 -
the biggest advance in industrial head protection in over 45 years.
The EVO8 is designed for today’s highest risk environments where high
impact / side impact situations are a concern such as Construction,
Mining, Tunnelling, Demolition, Oil and Gas, Offshore Marine, Refi nery
and Petrochemical, High Pressure Jetting and certain Emergency Services.
EN14052 is specifi ed into EN1789 as a mandatory requirement for each crew member for type B & C road ambulances.
Designed and developed over two years, EVO8’s excellent build quality
complements the high standard of design and materials which go
into the helmet, including features such as a high density liner and a
comfortable new harness system which create unparalleled wearer
comfort and acceptability.
EN14052 requires the helmet to withstand over 100 joules crown
impact (compared to 49 joules under EN397) and for the fi rst
time to withstand side impact protection of over 50 joules
to an angle of up to 60° from vertical
in a 360° radius around the shell.
Like all JSP safety helmets, the Mk8 EVO™ can be
branded with your corporate logo or company details.
There is space for branding on the front, sides and
back. Printed helmets can be delivered within ten
working days from JSP’s receipt of approved artwork.
3
MK8 EVOLUTION® HELMET - HEAD PROTECTION
AHS158-30_-_00Non Ventilated
MK8 EVO with Steel
bracket & cable loop
8
Mk8 EVO™ EN14052 for MinersThe MK8 with cable loop and steel lamp bracket.
AHS240-00_-_00Non Vented MK8
EVO with 4 point
chinstrap
8
Mk8 EVO™ EN14052 for LinesmanThe MK8 with 4 point mounted chinstrap.
04 Blue 05 Red 08 Orange
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050
ATTACHMENTSInternational slot enables fi rm fi tting
of a range of ‘Surefi t™’ safety visors
and ear defenders Wide variety
of visors available, Incorporates
steel springs for easy
deployment and retraction.
High perfomance Surefi t™ ear
protection offers an SNR of 28.
COMFORTExtremely comfortable terylene webbing moulds
to the individual wearer’s head. Lightweight
EPS liner reduces weight while still offering
maximum protection.
IMPACT PROTECTIONSide, front and rear impact protection from the
Shock absorbing EPS liner. Vented liner to increase
comfort whilst maintaining high protection factor.
Liner optimises low
angle impact
performance.
CODE DESCRIPTION CARTON QTY
HELMET COLOURSPlease insert the following two digit number in place of the dashes into
the code of your required Helmet to indicate your colour selection on
your order. For additional colours please contact your local distributor.
01 White 02 Yellow 03 Green 05 Blue 06 Red 08 Orange
Mk8 EVO™ EN14052 High Impact & Side Impact Helmet
AHU150-000-_00Ventilated MK8 EVO
WRH EN14052 High
Impact Helmet
8
AHS150-000-_00Non Ventilated MK8
EVO WRH EN14052
High Impact Helmet
8
AHS156-10_-_00Non Ventilated MK8
EVO with plastic
bracket for LED lamp
8
AHV300-001-000 LED lamp for Helmet
with plastic bracket10
Mk8 EVO™ EN14052 for Railway Specifi cationsThe MK8 with plastic lamp bracket for JSP LED lamp.
CODE DESCRIPTION CARTON QTY
SO WHY DID JSP DEVELOP THE EVO8™? JSP were approached by several large construction companies and civil engineers directly and asked the question could we develop a ‘safer helmet’ with side impact protection built-in?In 2007/2008, almost 2,000 people in the UK met with severe but non-fatal head injuries and a further 39 people died from head injuries sustained
in the workplace. These statistics would suggest a requirement for higher crown impact protection and proper benchmarked side impact protection.
A real life situation gives insight to the requirement for proper benchmarked side impact protection. A linesman at a major civil engineer received
a side impact working at height wearing a modern “lightweight” EN397 helmet. Concussed and hanging in his harness, the company was forced to
carry out a dangerous rescue at height. An EN14052 helmet would have provided signifi cantly better protection and most probably have avoided
this situation happening.
Ultra high strength outer shell. Ribbed upper
section dissipates impact energy. All Round
Protection, down to 60° from vertical. Large print
area on front & sides for logo printing.
OUTER SHELL
ADJUSTMENTIntuitive thumb and fore fi nger press points for
easy adjustment of the wheel ratchet, offers
diverse size ranges for true ‘One Size Fits All’
Ventilation convects hot air
out and draws in cool air,
reducing helmet
temperatures by
an average
2-3 degrees.
VENTILATION OPTION
4 5
6 7
ATTA
CHM
ENTS
RETR
ACTA
SPEC
SHOR
T PE
AK
BRAN
DING
1
VENT
ILAT
ION
Hot air out of the roof of the helmet, whilst at the same time sucking in cooler air in from the bottom of the helmet. Reduce helmet temperatures by an average 2-3 degrees
2
ADJU
STM
ENT
Slip or WheelRatchet optionsavailable.
Universal slot enables fi rm fi ttingof Contour ear defenders and a range of ‘Surefi t™’ safety visors for complete above the head protection, meaning all your protection is to hand and easy to deploy.
3
COM
FORT
Extremely comfortable terylene webbing moulds to the individual shape of the wearer’s head. Rain channel, directs rain away from wearer.
The helmet with integral visor ensures that eye protection is on hand when needed and never lost, whilst removing the need for additional eye protection. Protects to EN166.1.F.
Reduced peak for better vision whilst working at heights.
Extra large area for logos on the
front, sides, and rear.
HEAD PROTECTION - Mk7™ HELMET
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
MK7 FEATURES & BENEFITSThe JSP Mk7 is the ultimate in EN 397 head protection. Years of research and
development went into creating the most
comfortable, safest helmet available, packed
with features to maximise comfort and safety.
All round head protection, protects the head from every angle not just the “magic circle” on the crown required for EN 397.
1
2
4
5
6
7
3
a
8
ELEC
TRIC
AL
The MK7 helmet is now available with the EN 50365 Class 0 10KV standard. This standard is applicable to electrically insulated helmets used for working live or close to live parts on installations not exceeding 1000Vac or 1500Vdc.
RIGH
TS RESERVED
DESIGN REGISTERED
™
HELMET COLOURSPlease insert the following two digit number in place
of the dashes into the code of your required Helmet
to indicate your colour selection on your order. For
additional colours please contact your local distributor. 01 White 02 Yellow
15 Hi-Vis 03 Green 05 Blue 06 Red 08 Orange 11 Black 04 Grey
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 5
ACCESSORIES FOR Mk7 & Mk8 - HEAD PROTECTION
Mk7™ Without RetractaspecAll the advanced features of the Mk7, for people who prefer to wear separate eye protection.
Mk7™ Fitted With Retractaspec The Mk7 helmet has been designed with comfort, performance and style in mind and
incorporates the most innovative features seen yet on a safety helmet. Conforms to EN 397.
AHN120-00_-_00 MK 7 STD Peak, Ventilated, Easyjust™ Slip Ratchet 10
AHM120-00_-_00 MK 7 STD Peak, Non Ventilated, Slip Ratchet 10
AHN140-00_-_00 MK 7 STD Peak, Ventilated, Twist-Lok Wheel Ratchet 10
AHM140-00_-_00 MK 7 STD Peak, Non Ventilated, Twist-Lok Wheel Ratchet 10
f
AHN120-10_-_00 MK 7 STD Peak, Ventilated, Easyjust™ Slip Ratchet 10
AHM120-10_-_00 MK 7 STD Peak, Non Ventilated, Easyjust™ Slip Ratchet 10
AHN140-10_-_00 MK 7 STD Peak, Ventilated, Twist-Lok Wheel Ratchet 10
AHM140-10_-_00 MK 7 STD Peak, Non Ventilated, Twist-Lok Wheel Ratchet 10
CODE DESCRIPTION CARTON QTY
MK7™ SAFETY HELMET
Mk7™ Only Sureslide™ Retractaspec Polycarbonate EN166.1.FEasy assembly kit for those wishing to add retractable eyeshields to their existing Mk7 helmet.
ANS010-200-000 Replacement Surefi t™ Retractaspec Polycarb Visor - Clear 200
ACCESSORIES TO FIT MK7™& MK8® HELMETS
*Can be supplied with Short Peak / Call Sales Offi ce - or for Linesman (page 7)
MK7™/MK8® Surefi t™ Contour Helmet Mounted Ear DefendersDesigned for added long-term comfort and increased protection. Easy to attach and
detach with spring loaded arms that give an excellent fi t to the ear. When not in use
the arms allow the cups to stand off clearly from the head. SNR 28
AEJ030-001-100 Contour Helmet Mounted Ear Defenders - Black 50
AEJ030-000-500 Contour Helmet Mounted Ear Defenders - Blue 50
MK7™/MK8® Surefi t™ 20cm Unbound Polycarbonate VisorOffers protection against medium energy high speed particles at 120 m/s (270 mph),
liquid droplets and molten metal. Markings: EN166 1.B.3.9
MK7™/MK8® Surefi t™ 20cm Unbound Acetate VisorOffers protection against low energy high-speed particles at 45 m/s (101 mph) and
liquid droplets. Markings: EN166 1.F.3
MK7™/MK8® Only Visor CarrierVisor carrier clips into ear defender housing and fi ts both standard and short peak helmets.
ANV000-001-10A Surefi t™ Visor Carrier for MK7 20
ANV000-001-108 Surefi t™ Visor Carrier for MK8 20
ANX060-230-000 Surefi t™ “Contour” 20cm Unbound Polycarb Visor 20
ANX010-230-000 Surefi t™ “Contour” 20cm Unbound Acetate Visor 20
g
h
e
b
MK7™ Helmet for High Temperature (EN397: +150°c)High performance polymers are used to give a heat resistant shell for
applications such as foundries and metal smelting to protect against
radiant heat – EN397 high temperature option.
AHR120-000-100 MK7 STD Peak Non Ventilated White EN397:+150°c 10
d
i
a
b
c
d
e
MK7™ Only Surefi t™ Helmet Mounted Visor Carrier complete with Polycarbonate VisorVisor carrier clips into ear defender housing and fi ts both standard and short peak
helmets. Supplied fi tted with polycarbonate visor or separately with other visor
options. Polycarbonate - EN166.1.B,3,9 Acetate - EN166.1.F.3
ANW060-230-00A Visor Carrier c/w 20cm Polycarbonate Visor (MK7 Only) 20
ANW310-230-000 Visor Carrier c/w 20cm Polycarbonate Visor for Electrical Resistance EN166: 3.8.9.B (MK7 Only) 20
f
g
h
i
NEW
NEW
Mk3 - HDPE Comfort Plus™/Wheel RatchetThese stylish helmets are tough, functional and offer an extremely comfortable 6-
point terylene harness with wheel ratchet adjustment system offering a secure fi t on
the head for prolonged periods of use. Hearing and faceshield accessories can also be
fi tted. Conforms to EN397, ANSIZ89, EN50365
Mk3 - HDPE Comfort Plus™/Slip RatchetThese stylish helmets are tough, functional and offer an extremely comfortable 6-
point terylene harness with slip ratchet adjustment system offering a secure fi t on
the head for prolonged periods of use. Hearing and faceshield accessories can also be
fi tted. Conforms to EN397, ANSIZ89, EN50365
HEAD PROTECTION - SAFETY HELMETS
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
AHC110-00_-_00 Mk3 HDPE Comfort Plus/Slip Ratchet 40
AHF110-00_-_00 Mk3 HDPE Comfort Plus/Slip Ratchet (Short peak) 40
CODE DESCRIPTION CARTON QTY
AHC130-00_-_00 Mk - 3 HDPE Comfort Plus/Wheel Ratchet 35
Mk2 - HDPE Standard Poly/Slip RatchetManufactured from impact-resistant UV stabilised high density polyethylene. With an
adjustable 6-point low density polyethylene harness and fully adjustable slip ratchet
headband. Hearing and faceshield accessories can also be fi tted. Conforms to EN397,
ANSIZ89, EN50365
FF European - HDPE VentilatedA continental style fl at-fronted helmet with closeable ventilation ports providing
greater comfort in warmer weather. Shell manufactured from UV stabilised High
Density Polyethylene. With an adjustable 6-point low density polyethylene harness
and fully adjustable slip ratchet headband. Hearing and faceshield accessories can also
be fi tted. Conforms to EN 397, ANSI Z89.
HELMETS WITH POLYETHYLENE HARNESS
Mk1 - HDPEThis lightweight helmet combines safety with economy and is designed for basic
general use. The shell is manufactured from UV stabilised high density Polyethylene.
With an adjustable 6-point low density polyethylene harness and fully adjustable slip
ratchet headband. Light and comfortable to wear. Conforms to EN397, ANSIZ89.
AHA010-00_-_00 Mk1 - HDPE 40
AHB010-00_-_00 Mk 2- HDPE Standard Poly/Slip Ratchet 40
AHF010-00_-_00 Mk 2- HDPE Standard Poly/Slip Ratchet (Short peak) 40
AHL040-00_-_00 Standard Poly/Slip Ratchet 20
HELMETS WITH COMFORT HARNESS
FORESTRY HELMET
AHM124-600-800 Mk7 Forestry 14
CODE DESCRIPTION CARTON QTY
Forestry HelmetA popular combination helmet comprising of: Orange
Mk 7 Helmet with slipratchet complete with Surefi t™
visor carrier: 20cm/8” Wire Gauze Visor and Contour
Ear Defenders: SNR=28. Conforms to EN397 EN50365
EN352-3 & EN1737
HELMET COLOURSPlease insert the following two digit number in place of the dashes into
the code of your required Helmet to indicate your colour selection on
your order. For additional colours please contact your local distributor.
01 White 02 Yellow 03 Green 05 Blue 06 Red 08 Orange
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 7
HELMET ATTACHMENTS & ACCESSORIES - HEAD PROTECTION
HELMETS FOR LINESMAN
AHG110-00_-_00 Invincible Linesman 40
CODE DESCRIPTION CARTON QTY
Invincible® Linesman - HDPEInvincible Short Peak Comfort Plus helmet
combined with a linesman 3-point chinstrap
harness. Conforms to EN397& EN50365, ANSIZ89
AHP210-00_-_00 Mk7 Un-vented Slip Ratchet 10
Mk7™ Linesman - HDPEBased on the Mk7 helmet, with 3-point chinstrap
harness. Conforms to EN397& EN50365, ANSIZ89.
Can be fi tted with Retractaspec.
HELMETS FOR MINERS
AHM121-30_-_00 Mk7 Miners 10
CODE DESCRIPTION CARTON QTY
Mk7™ MinersMk7 helmet with cable loop & steel
lamp bracket, un-vented (slip) (without
Retractaspec)
OTHER HELMET ACCESSORIES
ANF010-200-000 Clear Poly Visor 10x10
CODE DESCRIPTION CARTON QTY
Polycarbonate Visor - ClearEasy assembly kit for those wishing to add
eyeshields to their existing Mk3, Mk2 or Mk1
helmets. EN166.1.F
AHV000-400-000 Helmet Comforter 50
Helmet ComforterFull head comforter for JSP Helmets.
AHV380-001-100 Black 25
AHV380-001-500 Hi Visibility 25
Thermal Helmet WarmerFull head and face comforter for JSP Helmets.
Available in black and high visibility yellow.
AHV000-500-000 Deluxe Chin Strap 250
Deluxe Chin Strap with Chin CupDeluxe wide elastic chin strap with chin cup,
releases automatically with forces between 150 and 250 Newtons. When
fi tted to JSP Industrial Safety Helmets, meets the requirements of EN397.
When fi tted to JSP Industrial Bump Caps, meets the requirements of EN812
AHV001-100-000 Elasticated chin strap 500
Elasticated Chin StrapWhen fi tted to JSP Industrial Safety Helmets, meets the requirements of EN397.
When fi tted to JSP Industrial Bump Caps, meets the requirements of EN812
AEJ020-001-100 Helmet Mounted Ear Defenders - Black 50
CODE DESCRIPTION CARTON QTY
Surefi t™ “Thruxton” Helmet Mounted Ear Defenders - BlackSurefi t™ Ear Defenders. Fit securely to JSP helmets
with stand-off positioning. H=31 M=23 L=16 SNR=26
EN352-3. For use with Mk 2/3 & FF European helmets.
SUREFIT™ ATTACHMENTS FOR MK2, MK3, MK7 & FF EUROPEAN
Surefi t™ Visor Carrier c/w 20cm Polycarbonate Unbound VisorOffers protection against medium energy
high speed particles at 120 m/s (270mph),
liquid droplets and molten metal. The optical
qualities of the visor comply with the
requirements of optical class 1 (highest).
Markings: EN166 1.B.3.9
ANV000-001-10A Helmet Mounted Visor Carrier 20
Surefi t™ Helmet Mounted Visor CarrierVisor carrier clips into ear defender housing and
fi ts standard peak Mk2/Mk3 helmets. Supplied
fi tted with polycarbonate visor or separately
with other visor options. Polycarbonate -
EN166.1.B,3,9 Acetate - EN166.1.F.3
ANW060-230-00A Visor Carrier c/w 20cm Polycarbonate Unbound Visor 20
ANW310-230-000 Visor Carrier c/w 20cm Polycarbonate Visor for Electrical Resistance EN166: 3.8.9.B 20
Surefi t™ 20cm Unbound Acetate & Polycarb VisorUnbound acetate complies with the requirements
of optical class 1 (highest). Markings: EN166 1.F.3
Unbound Polycarb complies with the requirements
of optical class 1 (highest). Markings: EN166 1.B.3.9
ANX010-230-000 Acetate Visor 20
ANX060-230-000 Polycarb Visor 20
AHA800-000-000 250mm Leatherette Mk1/2/3 & FF Euro 20
AHA820-000-000 Brushed Nylon/Foam Mk1/2/3 & FF Euro 20
AHM800-000-200 250mm Leatherette Mk7 20
AHM820-001-100 Brushed Nylon/Foam Mk7 20
Sweat/Comfort Bands for Mk1/2/3 and FF EuropeanLeatherette/ LDPE (brushed nylon backed
foam sweatband) for use with helmet harness.
CODE DESCRIPTION CARTON QTY
NEW
HEAD PROTECTION - HARDCAP A1+®
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
INDUSTRY LEADING BUMP CAP TECHNOLOGY, THE ONLY BUMPCAP TO EXCEED THE A1+ VARIANT OF EN812The new HardCap A1+® is another major innovation from JSP in head
protection design. Designed to exceed the most recent standards,
EN812:1997+2001, years of thought and design iterations have
been undertaken to develop a product that is unrivalled in both
performance and style. Sleek and low profi le, it’s almost impossible
to distinguish from a standard ‘high street’ baseball cap.
The unique angled adjuster designed to fi t under the occipital
bone at the rear of the skull gives greatest retention yet, one size
really does fi t all. Particularly when combined with the castellated
protective liner, the liner is removable, therefore the cap part is
machine-washable for hygiene purposes. It has a terry-towelling
sweatband for added comfort and all colour-ways have subtle
refl ective piping for added visibility and safety.
3 PEAK SIZES AVAILABLE3cm Micro Peak
7cm Standard Peak
Offering high levels of
protection and comfort for
Police and Security services
SWEAT BAND
Terry towelling sweatband adds comfort
and absorption for the wearer.
ALL ROUND PROTECTION
The protective liner is removable, so the
outer cap is fully washable for hygiene
purposes and extended life cycle.
LOW PROFILE DESIGN
Ultra sleek low profi le design means the
HardCap A1+ is almost indistinguishable
from a high street ‘fashion’ baseball cap.
VENTILATION
Extra holes in the liner plus the two
mesh panels on the outer mean added
ventilation for coolness and comfort.
UNIQUE ADJUSTER
Unique one-handed angled adjuster to
quickly fi t, giving true ‘one size fi ts all’
Sizing ranges from 53 to 64cm head size.
Refl ective piping on all models adds
extra visibility and therefore safety in
all working environments.
REFLECTIVE PIPING
HI-VISIBILITY
Available in Hi-visibility orange and
yellow, great for low light environments
BRANDINGAdd your logo, either
embroidered or as a transfer.
Call our sales team for full details.
HardCap A1+ ALL ROUND PROTECTION
RIGH
TS RESERVED
DESIGN REGISTERED
5cm Short Peak
AHV310-000-000 LED Cap Lamp 10
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 9
HARDCAP A1+® - HEAD PROTECTION
BOURTON BUMP CAPBourton Bump Cap - HDPEThe Bourton Bump Caps are available in
White (01), Yellow (02),Green (03), Blue (05), Red (06) and Orange (08)
ABA110-00_-_00 Bourton Bump Cap - Comfort Plus/Slip 20
ABA010-00_-_00 Bourton Bump Cap - Standard Plus/Slip 20
ABB000-001-100 Brushed Nylon/Foam Sweatband for Bump Cap 20
CODE DESCRIPTION CARTON QTY
STANDARD 7cm PEAK HARDCAP A1+®
ABS000-002-100 Short 5cm Peak HardCap Navy/Navy 20
ABS000-001-100 Short 5cm Peak HardCap Black/Black 20
ABS000-005-000 Short 5cm Peak HardCap Black/Grey 20
ABS000-00L-500 Short 5cm Peak HardCap Grey/Red 20
ABS000-00N-400 Short 5cm Peak HardCap Royal Blue/Yellow 20
ABS000-00N-500 Short 5cm Peak HardCap Black/Hi-Viz Orange 20
SHORT 5cm PEAK HARDCAP A1+®
ABT000-001-100 Micro 3cm Peak HardCap Black 20
ABT000-002-100 Micro 3cm Peak HardCap Navy 20
MICRO 3cm PEAK HARDCAP A1+®
ABS000-001-500 Hi-Viz Short 5cm Peak HardCap Yellow 20
ABS000-001-600 Hi-Viz Short 5cm Peak HardCap Orange 20
HI-VIZ SHORT 5cm PEAK HARDCAP A1+®
ABT000-30L-500 Micro 3cm Peak (w/Refl ective Peak) HardCap Grey/Red 20
MICRO 3cm PEAK (W/REFLECTIVE PEAK)
ABR000-000-500 Standard 7cm Peak HardCap Navy/Navy 20
ABR000-001-100 Standard 7cm Peak HardCap Black/Black 20
ABR000-005-000 Standard 7cm Peak HardCap Black/Grey 20
ABR000-00L-500 Standard 7cm Peak HardCap Grey/Red 20
ABR000-00N-400 Standard 7cm Peak HardCap Royal Blue/Yellow 20
ABR000-00N-500 Standard 7cm Peak HardCap Black/Hi-Viz Orange 20
LED CAP LAMP FOR HARDCAP A1+®
Add your logoAdd your logo to our products to our productsAdd your logo to our products
logologoEXPRESSEXPRESSlogologoEXPRESSEXPRESS™
10 WORKING DAY
SERVICELogo Colours• A maximum of 6 colours can usually be printed with an
optional full colour logos 256 colours.
• Ink colours may vary slightly when printed on different
safety helmet colours. We do not recommend printing
light colours onto dark coloured helmets because the
helmet colour may show through the ink.
• It is important to identify the colour of the safety helmet
on your order form. Your helmet colour may be one of
the colours in your logo, thereby reducing the number of
colours charged in the logo price.
ArtworkThe preferred fi le format is for artwork created in Illustrator
and saved as .ai or .eps fi les. These can be emailed to
[email protected] or sent on disc/CD to Logoed Helmets
Dept, JSP Ltd, Worsham Mill, Minster Lovell, Oxon OX29
0TA. It may be possible for JSP to use artwork in other
formats, however these may incur additional set up charges
and additional time to produce proofs.
Proofi ngJSP will provide black and white proofs to size for your
approval. The production process begins from this date.
HEAD PROTECTION - LOGO EXPRESS
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
6 STEP GUIDE TO PLACING YOUR ORDER
SELECT HELMETChoose which helmet you want to buy, where you want
your logo printed and how many colours are in the logo
SUPPLY ARTWORKSupply artwork by email or disc/CD (Preferably as EPS)
APPROVE ARTWORK PROOFSJSP will produce black and white proofs for your approval
CONFIRM ORDERConfi rm your order by fax to 01993 824411
RETURN PROOFSSign, date and fax back to 01993 824411. Alternatively
please state any amendments that you require.
DELIVERYDelivery of printed helmets in 10 working days from
JSP’s receipt of approved artwork
1
2
3
4
5
6
Please note: These dimensions are indicative of standard print areas. Location and
shape of logo will effect its maximum printable size on the helmet and any signifi cant
increase to the dimensions shown may result in possible distortion of logo.
HELMET LOGO MAX PRINT AREAS Mk2, Mk3, Mk7
NEW SIMPLIFIED SIZING
Front, Back or Sides: 70mm x 70mm
NEW MAXI SIZE Mk7 ONLYFront Only: 120mm x 70mm
HELMET LOGO PRINT AREAS Mk8Front, Back or Sides: 80mm x 40mm
HARDCAP A1+ EMBROIDERY
NEW INDIVIDUAL BRANDINGWe can now offer individual helmet personalisation at low cost to further enhance identity to your head protection.
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 11
LOGO EXPRESS - HEAD PROTECTION
NEW INDIVIDUAL PERSONALISATION FOR MK7 SAFETY HELMETSJSP is pleased to offer this new revolutionary service thanks to our NEW Printing Process:With the increased number of temporary workers and the greater need for identifi cation on work sites and in industrial
environments, JSP has researched and developed a new COST EFFECTIVE Printing Process to fulfi l today’s requirements :
SIMPLE AND EFFECTIVE:MOQ (MINIMUM ORDER QUANTITY) OF 10 Mk7
Please just send an Excel Spreadsheet with names or descriptions you want to mention on each helmet (using the right
font you want JSP to print with)
AND WE WILL MANAGE THE REST…Each Mk7 Safety Helmet supplied will be then printed on the rear (or wherever you wish) with the individual names supplied
on the Excel sheet, in black, with useful information (contact number, ID number etc.…) to a maximum width of 70mm.
BENEFITS:• Personal Protective Equipment for
each worker – fully traceable
• Added security and personnel identifi cation on site
• People can recognize other members
of the team without
badge, or without having met
them before.
• Increased personnel responsibility
• Low Fixed Cost
• Low MOQ
Enhance your corporate identity by having your company
logo or promotional message applied to your Hardcap
A1+. JSP offer ultra high quality embroidery service or
screen printing service using stain fast inks (guaranteed
for minimum 50 washes). Simply send through the logo
or message you require, stating the method required ie
embroidered or screen printed and we will do the rest.
Minimum order quantities and set up charges will apply.
Please call sales offi ce for details. Also available transfer printing.
HardCap A1+ ALL ROUND PROTECTION