Quality Tools for Quality Installation:

Joining Tools for Plastic Pipe and Fittings

SAVES TIME

EASIER INSTALLATION

REDUCES LABOR COSTS

Now There’s a Quick, Accurate Way to Bevel Pipe

The Power Beveling Machine will greatlyreduce the amount of time and labor requiredto bevel the ends of plastic pipe for solventcementing or insertion into elastomeric joints.It has been engineered and designedspecifically for use on such piping materialsas PVC, CPVC and ABS.

UNIQUE FEATURES1. Reduces man-hours and labor costs.

2. Produces accurate and consistent bevels every time.

3. Automatic, spring-loaded “squaring” device makespipe O.D. tracking easy and effortless.

4. Built-in chip catcher shields operator from flying debrisand reduces clean up.

5. Helps installer meet the large diameter bevelingrequirements as specified in ASTM D-2855.

6. Satisfies all manufacturers’ beveling recommendationsfor plastic pipe, fittings and solvent cements.

POWER BEVELING MACHINE

Plastic Pipe and Fitting Joining Tools

Product No.

PPB-1000

NominalPipe Size

4”-24”

StockNo.

12814

This portable power tool is especially valuablewhen large diameter (4”-24”) plastic pipeneeds to be bevelled.

The Quick & Easy Way to Join Large Plastic Pipe & Fittings

This new pipe and fitting puller gives contractorssomething they’ve never had before–exact, tight-fittingjoints in half the time required by present methods.

Designed specifically for large diameter plasticpipe and fittings, this remarkable tool is lightweight,durable and can easily be operated by one man.Compare these features with the products and methodyou’re now using:

1. Positive gripping–will not crush, crack or notchplastic pipe.

2. Unique center-line attachments assureproper alignment.

3. Allows pipe to be inserted to the proper fittingsocket depth. (As specified in ASTM D-2855.)

4. Holds freshly cemented joints to prevent fittingfrom backing off.

Not only does the pipe puller make theperfect joint, it reduces installation time.

APPLICATIONS• PVC / CPVC / ABS

SOLVENT CEMENTED SYSTEMS• OTHER TYPES OF PIPING

ProductNo.

P-0412

P-1420

NominalPipe Size

4”-12”

14”-20”

Approx.Weight (lbs)

40

70

(All necessary attachments are included)

The lightweight PULLER-CLAMP is easyto transport and assemble. This makesthe unit very practical for close workin a trench or high up on a pipe rack.

Quick and simple adjustments allowthe puller to be properly sized to fit agood range of pipe diameters. A metricO.D. model is also available forspecialty piping.

A forward tug on the handle locks thepuller tightly to the pipe surface. A tugin the reverse direction will unlock itfor removal or adjustment.

A powerful winch produces the forcenecessary to bottom out any solventcemented pipe and fitting. The winchhas an interlocking pawl system thatwill not slip even if wet or oily.

Choose the proper fitting attachmentas needed. The attachments havebeen uniquely designed to fit a widevariety of pipe fittings.

The puller will operate in a horizontalor vertical position. The winch willoperate smoothly right side up or upsidedown. Solvent cemented joints can beleft locked up until the cement beginsto “set”, no backing off of the fitting.

PIPE AND FITTING PULLER

StockNo.

12816

12815

Note: Elbow block suppliedonly with model P-0412

Reduce Pipe Preparation & Installation Time

455 W. Victoria Street, Compton, CA 90220Toll-free 800-421-2677 • Tel: 310-898-3300 • Fax: 310-898-3390

www.ipscorp.com

IPS CORPORATION

• Bevels pipe in seconds with little effort

• Accommodates 1/2”CTS through 3” IPS thermoplastic pipe

• Heat treated aluminum cones with proper bevel angles

• High speed steel cutter blades

• Geared for proper speed and optimal performance

• Sturdy base plate with mounting holes

• Ideal for production where pipe is pre-cut, for preparationof laboratory test samples or fabrication work

• Readily available replacement parts

This power beveling tool (chamfering tool) isdesigned for use on thermoplastic pipe (1/2”CTSthrough 3” IPS) and is powered by a right anglegearmotor with permanently lubricated ballbearings on the output shaft and motor shaft.The outside diameter beveling cone chain drivesthe inside diameter deburring cone that ismounted on pillow block bearings. Beveling anddeburring cones are heat-treated cast aluminumwith high speed steel cutter blades. The powdercoated 12 gauge steel base plate can beclamped or bolted to a work bench.

SPECIFICATIONSNominal F/L RPM @ 60Hz - 86 RPMF/L Amps @ 115 VAC and 60Hz - 2.0 AmpsCapacitor MFD (370 VAC) - 15 MFDTool Size: 14” wide, 81/2” high, 111/2” deepTool Weight: 26 lbs

Gently pushing pipe into the O.D. beveling cone willquickly produce the proper bevel.

MOUNTED POWERBEVELING TOOL

Product No.

MPB-2000

NominalPipe Size1/2”CTS - 3”IPS

StockNo.

12863The I.D. beveling cone removes sharp edges fromthe inside pipe diameter for smoother fluid flow.

Made in the U.S.A. ©IPS 05/05 vpd