ires_ final_presenation
TRANSCRIPT
![Page 1: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/1.jpg)
1
The Effect of Cathode Stoichiometric Ratio on PEMFC
Performance in Cold Operating Conditions
东 方 (Carl Cayabyab), Oakland University蓝 天 (Jonathan Guidoboni), The George Washington University
任 龙 (Holden Ranz), Lafayette College
National Science FoundationInternational Research Experience for
Students 2011
快乐队
![Page 2: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/2.jpg)
2
Background Cold-start conditions and Stoichiometric ratio Project Design Methods and Procedures Equipment and Calibration Results Analysis Conclusions
Outline
![Page 3: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/3.jpg)
3
Background
Proton exchange membrane fuel cell (PEMFC)
Chemical energy Electrical energy Hydrogen ions + Oxygen Water Voltage difference makes current flow
GDL – conductive carbon cloth or paper. Porous material, gases pass through to catalyst layer
CCL – catalyst layer, encourage separation of inlet gas atoms into ions / electrons for easier and faster reaction
![Page 4: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/4.jpg)
4
Interest
Advantages: high power density, extremely low pollutant emissions, and low operating temperature
Vehicle applications
Reduce dependence oil
Lower harmful emissions
Hydrogen very abundant resource
![Page 5: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/5.jpg)
5
Cold-start Conditions
PEMFC normally operate at 70 to 80°C
Cold climates, sub-freezing temperatures
Ice blocks pores in membrane and GDL suppresses FC performance
More difficult to start, especially on its own
![Page 6: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/6.jpg)
6
Actual / Theoretical Ratio of air cathode StC
Ratio of hydrogen anode StA
Stoichiometric Ratio
![Page 7: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/7.jpg)
7
Initially Relative Humidity Manipulated Variables
Heating jacket voltage (V) relative humidity (%) Flow rate (L/min) Applied current load (A)
Controlled Variable Output cell voltage (V)
Perform trials in both cold and room temp conditions Trend between relative humidity and cell performance Difference between cold and room temp conditions
Project Design
Hygrometer
![Page 8: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/8.jpg)
8
Project Design - RedirectedStoichiometry and Temperature Manipulated Variables
Flow rate (L/min) Stoichiometric ratio Temperature Applied current load (A)
Controlled Variable Output cell voltage (V)
Objectives trends between FC performance, StC, and temperature conditions Analyze behavior of the membrane and GDL at sub-freezing
temperatures.
![Page 9: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/9.jpg)
Project Schematic
![Page 10: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/10.jpg)
1. Open nitrogen tank to 1MPa2. Turn on water heater to 45°C3. Check for leaks using soapy
water4. Run water pump for 5 minutes5. Turn off nitrogen gas. Hook
up air and hydrogen tanks.
Procedures
![Page 11: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/11.jpg)
6. Turn on multimeter and computer program.
7. Open hydrogen and air tank to 1MPa
8. Adjust flow rates to an Stc of 2.5
9. Gather temperature readings every 30 seconds
10. Record voltage every 3 minutes and increase current density. Change flow rates as well.
Procedures
![Page 12: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/12.jpg)
11. Stop fuel cell once voltage change is small.12. Save data. Flush out water with air for 5
minutes.13. Repeat this for Stc ratios of 3 and 4
14. Repeat process for 0°C and -3°C.
Procedures
![Page 13: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/13.jpg)
Polyurethane Tubing (6mm OD) Fan Water Heater Insulation PEMFC Humidifier
Equipment
![Page 14: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/14.jpg)
Freezer (FYL-YS-108L) Rubber Plug 2 Thermocouples Digital Thermometer Soapy Water
Equipment
![Page 15: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/15.jpg)
Digital thermometer accurate 0.05°C Accuracy
Calibrated 2 thermocouples Air inlet Hydrogen inlet
Calibration
![Page 16: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/16.jpg)
Methods of Calibration Water bath with varying temp Take temp readings at the same point Steady state Plot curves to find factor
Calibration
![Page 17: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/17.jpg)
Calibration
25 30 35 40 45 50 55 60 65 70 750
10
20
30
40
50
60
70
80
f(x) = 0.987641858423725 x − 0.844592921186269R² = 0.999771752535319
Thermocouple A
Measured Thermocouple Temp (°C)
Accura
te D
igit
al Tem
p (
°C)
20 30 40 50 60 70 800
10
20
30
40
50
60
70
80
f(x) = 0.984437921197337 x + 0.297763787459076R² = 0.999880689487375
Thermocouple B
Thermocouple C
Measured Thermocouple Temp (°C)
Accura
te D
igit
al Tem
p (
°C)
Thermocouple A:Y=0.9876X-0.8446
Thermocouple B:Y=0.9844X+0.2978
![Page 18: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/18.jpg)
Ideal Flow Rate Calculations
where = molar flow rate of reactant (mol/s), = moles of electrons per mole of reactant (mol e-/mol), = Faraday’s constant = 96485 C/mol. = = current load on the fuel cell (A),
= current density (A/cm2),
and = active area of the fuel cell = 32 cm2 (FC1), 16 cm2 (FC2)
H2 = 2
H2 = 4
![Page 19: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/19.jpg)
Flow Rates for Stc valuesAir M = 0.0288479 kg/mol
ρ = 1.205 kg/m3Ideal Q (L/min) Actual Q (L/min)
i (A/cm2) I (A) v (mol/s) ṁ (kg/s) 1 MEA 2 MEA Stc = 2.5 Stc = 3 Stc = 4
0.05 1.6 1.974E-05 5.695E-07 0.028 0.057 0.142 0.170 0.227
0.1 3.2 3.948E-05 1.139E-06 0.057 0.113 0.284 0.340 0.4540.15 4.8 5.922E-05 1.709E-06 0.085 0.170 0.425 0.510 0.681
0.2 6.4 7.897E-05 2.278E-06 0.113 0.227 0.567 0.681 0.9070.25 8 9.871E-05 2.848E-06 0.142 0.284 0.709 0.851 1.134
0.3 9.6 1.184E-04 3.417E-06 0.170 0.340 0.851 1.021 1.3610.35 11.2 1.382E-04 3.987E-06 0.198 0.397 0.992 1.191 1.588
0.4 12.8 1.579E-04 4.556E-06 0.227 0.454 1.134 1.361 1.815
Hydrogen M = 0.002 kg/molρ = 0.08375 kg/m3
Ideal Q (L/min) Actual Q (L/min)i (A/cm2) I (A) v (mol/s) ṁ (kg/s) 1 MEA 2 MEA Stc = 1.5
0.05 1.6 8.291E-06 1.658E-08 0.012 0.024 0.0360.1 3.2 1.658E-05 3.317E-08 0.024 0.048 0.071
0.15 4.8 2.487E-05 4.975E-08 0.036 0.071 0.1070.2 6.4 3.317E-05 6.633E-08 0.048 0.095 0.143
0.25 8 4.146E-05 8.291E-08 0.059 0.119 0.1780.3 9.6 4.975E-05 9.950E-08 0.071 0.143 0.214
0.35 11.2 5.804E-05 1.161E-07 0.083 0.166 0.2490.4 12.8 6.633E-05 1.327E-07 0.095 0.190 0.285
Considerations: Active area = 32 cm2, fuel cell has 2 membranes
Assumptions: Air is 79% N2 and 21% O2, gas is flowing at NTP (20°C and 1 atm), constant density
![Page 20: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/20.jpg)
Data Collection
![Page 21: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/21.jpg)
Output voltage at 0.1 A/cm2
21
FC Performance Results
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(ii) Cold Start, 0°C
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(iii) Cold Start, -3°C
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(i) Room Temperature
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(ii) Cold Start, 0°C
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(iii) Cold Start, -3°C
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(i) Room Temperature
Stc = 2.5 Stc = 3 Stc = 4
Δ ≈ 0.1 V
Δ ≈ 0.08 V
Δ ≈ 0.9 V
Δ ≈ 0.08 V
Δ ≈ 0.07 V
Δ ≈ 0.03 V
Δ ≈ 0.06 V
Δ ≈ 0.06 V
Output voltage at 0.15 A/cm2
**Fluctuations most likely due to flow rate adjustments when switching between current loads
![Page 22: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/22.jpg)
22
Output voltages essentially the same for 0.1 and 0.15 A/cm2 at different Stc
FC Performance ResultsOutput voltage at 0.1 A/cm2 Output voltage at 0.15 A/cm20
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(ii) Cold Start, 0°C
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(iii) Cold Start, -3°C
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(i) Room Temperature
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(i) Room Temperature
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(ii) Cold Start, 0°C
Stc = 2.5 Stc = 3 Stc = 4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 20 40 60 80 100 120 140 160
Volt
age
(V)
Time (s)
(iii) Cold Start, -3°C
Stc = 2.5 Stc = 3 Stc = 4
![Page 23: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/23.jpg)
FC Performance – Polarization Curves
Initial loss due to activation of the fuel cell Linear loss due to resistance End loss due to concentration
0.0 0.2 0.4 0.6 0.8
0.2
0.4
0.6
0.8
1.0
Vo
lta
ge
(V
)
Current Density (A/cm2)
Experimental data Numerical resultsActivation
Loss
Ohmic Loss
Concentration
Loss
![Page 24: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/24.jpg)
Experimental Polarization Curves
Polarization curves mostly linear Ohmic losses
At room temp and 0°C, 2.5<3<4 At -3°C curves nearly identical Approximate current densities
resulting in failure: Room temp – I ≈ 0.33 A/cm2
0°C – I ≈ 0.30 A/cm2
-3°C – I ≈ 0.31 A/cm2
![Page 25: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/25.jpg)
25
Ice Formation?
After Room Temp Trial-water present in the form of foggy condensate
After Cold Temp Trial
-small droplets and ice crystal formation
![Page 26: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/26.jpg)
26
Cathode stoichiometric ratio affects fuel cell performance at room temperature and cold conditions
Increase in Stc at room temp and 0°C corresponds to increase in output voltage
Current densities ≥0.1 A/cm2
FC performance hardly affected by Stc changes at -3°C Linear polarization curves indicate resistance losses Ice formation inside gas lines creates blockages
FC stops generating electricity
Conclusions
![Page 27: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/27.jpg)
27
Flow meter instability and inaccuracy Tendency to get stuck
Inability to maintain constant operating temperature of the PEMFC
Duration of membrane humidification prior to testing
Recommendations Calibrate glass flow meters using digital meters Use the heat exchange line in fuel cell to
cool/maintain operating temperature Use a hot water bath to try to control relative
humidity
Sources of Error
![Page 28: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/28.jpg)
28
Kang Mi et al. Experimental Study on Dynamic Characteristics of Proton Exchange Membrane Fuel Cells (PEMFC) under Subzero Temperatures.
Shanhai Ge et al. Characteristics of subzero startup and water/ice formation on the catalyst layer in a polymer electrolyte fuel cell.
Jer-Huan Jang et al. Effects of operating conditions on the performances of individual cell and stack of PEM fuel cell.
US Department of Energy, http://www.energy.gov/.
References
![Page 29: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/29.jpg)
29
China is awesome. Flow chart of attitude
The China Experience
Before China…Meh
In China…快乐 !
Thought of leaving…
![Page 30: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/30.jpg)
30
First Impressions
Huge Lots of people Crazy cab drivers Water closet A lot of biking (crazy bikers)
![Page 31: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/31.jpg)
31
Places Visited
Beijing Zoo Temple of Heaven Summer Palace Tianamen Square
![Page 32: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/32.jpg)
32
Places Visited
Great Wall Shanghai Xi’an
![Page 33: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/33.jpg)
33
Foods
![Page 34: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/34.jpg)
34
Foods
![Page 35: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/35.jpg)
35
Activities with Students
Ping Pong Badminton Basketball Chinese Chess
![Page 36: IRES_ Final_Presenation](https://reader036.vdocuments.site/reader036/viewer/2022062300/55c4490fbb61eb83378b477d/html5/thumbnails/36.jpg)
36
China Experience
Exposure to research
Communication with Chinese students
Learning the language
Making new friends