iq eye collector/230 installation instructions

1IQ EYE Collector/230 Installation Instructions TG201022 Issue 1 8/5/08

Important: Retain these instructions

Installation Instructions

IQ EYE Collector/230Node Controller

1.2 STORING

��

+50 °C(122 °F)

0-10 °C(14 °F)

90 %RH

CONTENTS1 Installation .................................................................... 11.1 Unpacking ..................................................................... 11.2 Storing ........................................................................... 1

1.3 Installation - Fixing ........................................................ 11.4 Installation - Configuration ............................................ 52 Replacing a Fuse ........................................................ 143 End User Licence Agreement .................................... 164 Limitations of Use ....................................................... 165 Disposal ...................................................................... 18

1.3 INSTALLATION - FIXING

It is recommended that the installationshould comply with the HSE Memorandumof Guidance on Electricity at WorkRegulations 1989.For USA install equipment in accordancewith the National Electric Code.

!WARNINGOther than removing front covers,do not attempt to open the unit.Failure to comply may causedamage to the unit.

IQ EYE Collector/230Installation InstructionsTG201022

1 INSTALLATION1.1 UNPACKING

Requirements2a

��

0 °C(32 °F)

+45 °C(113 °F)

0 %RH 80 %RH

b c

Dimensions1

302 mm (11.89”) 60 mm (2.36”)

266

mm

(10

.47”

)

2 IQ EYE Collector/230 Installation Instructions TG201022 Issue 1 8/5/08

IQ EYE Collector/230 Installation Instructions

1.3 INSTALLATION - FIXING (Continued)

Remove Cover3a b

WARNING: Opening the panel may exposedangerous voltages.417-IEC-5036

Caution: This unit contains static sensitivedevices. Suitable anti-staticprecautions should be takenthroughout this operation to preventdamage to the units.

BS EN100015/1 Basic Specification: protection ofelectrostatic sensitive devices.

WARNING: The connecting leads may beconnected to supplies. Isolatebefore touching.

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

c

Mounting4a

b

M4, 5, or 6 (pan or CSK)or No 10 or 12 (CSK)

c

1 2 3 4 5 6 7 8 9 10

Rear view

d

1 2 3 4 5 6 7 8 9 10

e f

255 mm (10”)

Length depends on screwhead projection and screwtype

h

1 2 3 4 5 6 7 8 9 10

Rear viewi

1 2 3 4 5 6 7 8 9 10

2 x M4, 5, or 6(No 10 or 12)

1 2 3 4 5 6 7 8 9 10


Installation Instructions IQ EYE Collector/230


Route Cables5 Either oruse M20 grommet use M20 Copex glands

Pushouts

c

DO NOT APPLYPOWER

�

�

Connect Power

Use shrouded plugTerminal size 0.5 to 2.5mm2 (14 to 20 AWG)

6

1 2 3 4 5 6 7 8 9 10

WARNING: This apparatus must be earthed (via mains supply cable).

~L N E

L N E

a b

d e

� � � � � � � � � � � � � � � � � �

� � � ��

�

� � � �

� � � � � � � � �

� � � � � � �

� � � � � � � � � � �

� � � � � � � �

� � � � � � � � � � � � � � � � � � � � � � ��

� � �

�

� � �

� � �

� � � � � � � � � � �

� � � � �

� � � � � � � � �

� � � � � �

Connect Ethernet7

100

m (1

09 y

ds)

Ethernet hub/switch

Connect to an Ethernet hubUse Ethernet cable.

IQ EYECollector

RJ45 Connector

RJ45 Connector

Maximum Cable distance100 m (109 yds)

IQ SystemEthernetProductsEngineeringGuide TE200369



1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10


� � � � � � � � � � � �

� � � � � � � � � � � �

2 wire

Connect Current Loop8

X

TT

RR

4 5 6 7T- T+ R- R+

X

TT

RRTT

RR

4 5 6 7T- T+ R- R+

4 wire

Additional terminals

Note only 1 INC type node on a single Lan.

If the IQ EYE Collector’s current loop is not to be connected(i.e IQ EYE Collector is only to interface between Ethernetand Lon) a loop back should be fitted. as shown

1 2 3 4T- T+ R- R+IMPORTANT

Maximum Cable distance

Terminal size 0.5 to 2.55m2 (14 to 20 AWG)

Terminal size 0.5 to 2.55m2 (14 to 20 AWG)

9 Connect LonWorks Bus

Polarity independentTerminal size 0.5 to 2.55 m2

(14 to 20 AWG)

LON

1 2

Normal current loop Lan cable is not recommended.Do not use screened cable.

Maximum Cable distance

Note that the IQ EYE Collector is not compatible with LONC.The LONC must be bound on a LonWorks network, and the IQEYE Collector cannot be bound.

10Connect to PSTN

IQ EYE Collector(RJ11)

(RJ11)PSTN adaptor BT600(UK country specific)

PSTN Network

Only required if internet connection is to be made using a dial up connection.

Note that if the PSTN connection is being shared with a TMN a standard doubleradaptor should be used.

elbaC duab6k9 duab2k91 *duab4k83 seriWfo.oN2819nedleB )sdy0901(m0001 )sdy567(m007 )sdy545(m005 27029nedleB )sdy0901(m0001 )sdy545(m005 )sdy083(m053 2

002/FH/22/1/1/PTmetsySQI )1678nedleB( )sdy567(m007 )sdy083(m053 )sdy072(m052 2002/FH/22/2/2/PTmetsySQI )3278nedleB( )sdy545(m005 )sdy072(m052 )sdy531(m521 4

dednemmoceRselbaC htgnelsubxaM otedonxaM

edon20158nedleB )sdy545(m005 )sdy545(m005

dnerT002/FH/61/0/1/PT

)1748nedleB()sdy545(m005 )sdy034(m004

GWA22,VIleveLLU )sdy545(m005 )sdy034(m0048.0x2x2Y)tS(YJ )sdy545(m005 )sdy053(m02342,5.taCA865AIT

GWA )sdy094(m054 )sdy072(m052

If the LonWorks bus is not connected the Lontalk module’s‘Lontalk Enabled’ parameter MUST be set to ‘No’.



1 2 3 4 5 6 7 8 9 10


Replace Cover11a

b

1.4 INSTALLATION - CONFIGURATION

Fix Unit1

IQ EYE Collector/24Installation Instructionssection 1.3

Switch off2

O

I

1

Note that this product may involveLonWorks system integration. Thisprocedure should only be performed byan installer with LonWorks expertise.

!

1 2 3 4 5 6 7 8 9 10

Remove Cover3

1 2 3 4 5 6 7 8 9 10

WARNING: Opening the panel may exposedangerous voltages.417-IEC-5036 Caution: This unit contains static sensitive devices.

Suitable anti-static precautions should betaken throughout this operation to preventdamage to the units.

ab

c

WARNING: The connecting leads may beconnected to supplies. Isolate beforetouching. BS EN100015/1 Basic Specification: protection of electrostatic

sensitive devices.



1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

1.4 INSTALLATION - CONFIGURATION (Continued)

ADDRESS

ON

Set Internetwork Address (Lan number)4

SET

NOT SETe.g.

Address = 2 + 16 + 64 = 82

ON= A IQ EYE

Collector

Lan

Lan/= A

Lan/= A

Lan/= A

If address < 100, INC Mode If address = > 100, Internetwork Extension Mode

Address = A

address 1, 4 to 9, 11 to 119

0, 2, 3, 10 or >119

Internetwork(on Ethernet)


IQ EYECollector

Lan(on current loop)



IQ EYECollector

Internetwork(on current loop)

Set Current Loop Baud Rate5

SET

NOT SETIQ EYE Collector

Baud Rate = C

=C

=C

=C

=C

38k4 baud

Note 1: 38k4 Lan not available with IQ2xx, IQ1xx, INC, LINC,CNC, CNC2, INC2,and TMN.

Note 2: 38k4 Internetwork not available with INC, and LINC.

6 SET LonWorks Bus Terminator Link

��

��

OFFNo terminator, LonWorksbus must be terminatedelsewhere.

FREEUse to terminate LonWorksbus at IQ EYE Collector

��

��

19k2 baud

9k6 baud

Note that only one internetwork device is allowed on a Lantherefore ensure that the IQ Eye Collectors ’s Lan number is notused by another INC type device.



1 2 3 4 5 6 7 8 9 10


� � � � � � � �

� � � � � � � �

� � � � � � � �

Star topology

Bus topology

Loop topology

*Terminate LonWorks bus at one end only

*

LonASCN LonB

IQ EYECollector

A

1

IQLROUTER

2 3 4

B

1 2 3 4

IQL

x y

A

1

IQLROUTER

2 3 4

B

1 2 3 4

zw

IQL

x y zw

IQL

x y zw

IQL

x y zw

Recommend terminate at IQ EYE Collector using Lon terminator link

Otherwise terminate elsewhere using LONTERMINATOR. Terminate Lonbus at one end only.

Lon - FTT (free topology)*

*Do not allow wires tocross on a loop

Maximum 64 nodes perLonWorks segmentMaximum 40 IQLs (and LONCs)per virtual Lan

Terminated using IQLRouter’s Lon terminator link

100 � F, 50 V min

100 � F, 50 V min

Terminator

Terminated using IQLRouter’s Lon terminator link

6 SET LonWorks Bus Terminator Link (Continued)

�

�3

Install DHCP Server7 If the IP address settings (IP address, subnetmask, default router, and WINs server) are to besupplied by a DHCP server install one on thesystem if one is not already installed.

Switch OnRead Licence9 Read and agree to End UserLicence Agreement (theseinstructions Section 2).

10 The IQ EYE Collector willattempt to obtain its IP address

Install WINS Server8 If host names are to be used to connect to theEINC L install a WINS server on the system if oneis not already installed.

Check Status LEDs11

Power LED

Ethernet OK LED

Lon OK LED

Current Loop OK LED

RX LED

TX LED

Ethernet Data LEDEthernet Link LED

Power LED Ethernet OK LED Lon OK LED Current Loop OK LED+ + +

Normal Operation Indication (shown after 2 minutes)

If LEDs are not as above after 2 minutes check table below.

settings from a DHCP server if one doesnot exist it will go into link/local mode.

DEL DEL DEL DEL DEL ylsuounitnoC ylsuounitnoC ylsuounitnoC ylsuounitnoC ylsuounitnoC gnihsalF gnihsalF gnihsalF gnihsalF gnihsalF ylsuounitnoCffO ylsuounitnoCffO ylsuounitnoCffO ylsuounitnoCffO ylsuounitnoCffO

)eulB(rewoP yhtlaeHtinU yldetaeperecnognihsalFelifnoitarugifnoCEYEQIoN

yldetaepereciwtgnihsalFtenrehtEoneblliwereht,elbaliavatonsisserddaPI

snoitacinummoc.sgnittestenrehtEgniniatbO-s003<

sgnittestenrehtEniatbootelbanU-s003>.)erehweslestluafrofkcehC(

rehtokcehctluafasahtinuyldetaepergnihsalF.sDEL

.sserddadilavni-gnihsalfoslaerasDELneerg3llafI

tluaFrewoPytluaFtinU



1 2 3 41 2 3 4

RS232RS232 RxTx

OK

OK LONLON

1 21 2

28-36 V24 V ETHERNETETHERNET

TREND LANTREND LAN

T- T+ R- R+T- T+ R- R+LINK DATALINK DATA

LON

OK

LON

OK

LON

TERM

LON

TERM

ADDRESS - BAUDADDRESS - BAUD

SRV PINSRV PIN

1 2 3 4 5 6 7 8 9 10


Check Status LEDs (Continued)11

12 Connect to IQ EYE Collector with IP Tool

SET Manual TE200147IP Tool Manual TE200638

IQ EYECollector

Router

Either over Ethernet or Local PC Ethernet ConnectionSET v6(including IP Tool XCITE/XA crossover adaptor

order separately (XCITE/XA/5pack of 5)

SET v6(including IP Tool)

Local PC (Ethernet) connection can be either to adjacentEthernet hub using standard cable only, or directly to IQ EYECollector using standard cable and crossover adaptor,XCITE/XA.

Initially access IQ EYE Collector via its MAC address (written onlabel)

DEL ylsuounitnoC gnihsalF ylsuounitnoCffOKOtenrehtE

)neerG(KOtliubkrowtenretnitenrehtE tenrehtEoN-DELrewoPhtiwyletanretlagnihsalF

.).rotcennocro/dnaelbackcehC(.dnuofnoitcennoc:rofs21yrevetuobagnihsalF

.gnidliubkrowtenretnitenrehtE-s09<ylreporpgnidliubtonkrowtenretnitenrehtE-s09>

.)erehweslestluafrofkcehC(rO

.rebmuntropPDUemastasecivedrehtooNrO

.tluafadepolevedsahrotcennoC/elbaC

ytluaFtinU

KOnoL)neerG(

KOtliubkrowtenretninoL :rofsdnoces42yrevetuobagnihsalF.gnidliubkrowtenretninoL-s021<

ylreporpgnidliubtonkrowtenretninoL-s021>.)erehweslestluafrofkcehC(

rO.dnuofsecivednoLrehtooN

rOyltcerrocdetanimrettonnoL

ytluaFtinU

pooLtnerruC)neerG(KO

KOtliubnaL/krowtenretninoL :rofsdnoces21yrevetuobagnihsalF.gnidliubnaL/krowtenretnipooLtnerruC-s06<gnidliubtonkrowtenretni/naLpooLtnerruC-s06>

.)erehweslestluafrofkcehC(ylreporprO

.)sDELXRdnaXTkcehC(detcennoctoN.gnitacinummocsitinunehwyltnettimretnihsalflliW

ytluaFtinU

)wolleY(XR thgils,KOtiucricrevieceR.lamron=rekcilf

.deviecergniebatad-tsafsrekcilF tiucricrevieceRnekorb/detcennocsid

ytluaFtinUdetrohsseriwrevieceR

)wolleY(XT .lamron-rekcilfthgilSrettimsnarT-gnirekcilFoN

.detrohsebyamtiucric

tiucricrettimsnarT-s21yrevetuobasehsalF.detcennocsid

.dettimsnartgniebsiatad-tsafsrekcilF

ytluaFtinU

kniLtenrehtE)neerG(

dnuofecivedtenrehtE .)ytluafelbaC(tluaF ecivedtenrehtEoNebyamelbaC(.dnuof)ytluafrodetcennocsid

ataDtenrehtE)wolleY(

tluafelbaC .deviecergniebataD ecivedtenrehtEoNebyamelbaC(.dnuof)ytluafrodetcennocsid




Configure Addressing Details with IP Tool13 IQ EYE Collector Data SheetTA200800IP Tool Manual TE200638

The IQ EYE Collector’s addressing information can be set up automatically (automatic addressing) or manually (manualaddressing). When set up automatically the addressing details are obtained from a DHCP server, if a DHCP server is not beingused or fails the IQ EYE Collector enters link/local mode where it autonegotiates its IP address with other devices on its Ethernetsegment. Alternatively the settings can be specified manually. When automatic addressing is used the IQ EYE Collector’s IPaddress may vary, with manual addressing the IP address is fixed. The addressing details can be viewed or configured usingIPTool. The table below describes the options that must be set up for each addressing mode.

The table below describes the addressing parameters that need to be set up.

dohteMgnisserddAcitamotuA launaM

PCHD lacoL/kniLderiuqeRrevreSPCHD seY dellatsniebtontsuM oNderiuqeRrevreSSNIW seY emasnosecivedllafioN

.deriuqeresiwrehto,tenbusotnoitcennocfideriuqerylnOgnisuedamebotsisecived

.semantsohPCHD .tluafedehtsisihT.seYotteS .tluafedehtsisihT.seYotteS looTPIgnisuoNotteS

sserddAPI revresPCHDybteS rehtohtiwdetaitogenotuA.tenbusemasnosecived

.looTPIgnisudeificepsebtsuMPIdexifaesuotelbissopsitImetsysPCHDanosserddasirevresPCHDehtgnidivorp.sserddaehtetacollaottontes

ksaMtenbuS revresPCHDybteS 0.0.552.552sesU looTPIgnisudeificepsebtsuMretuoRtluafeD revresPCHDybteS A/N looTPIgnisudeificepsebtsuM

revreSSNIW revresPCHDybteS A/N looTPIgnisudeificepsebtsuMemaNtsoH ebnaC.desueulavtluafeD

.looTPIgnisudeificepsebnaC.desueulavtluafeD


.looTPIgnisudeificepstroPPDU ebnaC.desueulavtluafeD



.looTPIgnisudeificepsreifitnedI ebnaC.desueulavtluafeD



.looTPIgnisudeificepssretuoRssorcAkrowtenretnI tenbusdnaemantsohputeS

gnisusecivedetomerfoksam.looTPI

elbaliavatoN ,sserddaPI/emantsohputeSetomerfoksamtenbusdna

.looTPIgnisusecivedderiuqeRsCNClautriV tropdnasserddaCNCteS

htiwsCNCvderiuqerforebmunmralanisCNCvroF.looTPIemantsohehtputesoslaedomoterasmralahcihwotecivedfo

.tneseb

tropdnasserddaCNCteShtiwsCNCvderiuqerforebmun

mralanisCNCvroF.looTPIemantsohehtputesoslaedomoterasmralahcihwotecivedfo

.tneseb

tropdnasserddaCNCteShtiwsCNCvderiuqerforebmun

mralanisCNCvroF.looTPIsserddaPIehtputesoslaedomhcihwotecivedfoemantsohfo

tneseboterasmrala

retemaraP noitpircseD egnahcotnehWsserddA

eludoMreifitnedI .zz_yy_xx_DNERTotstluafedtI.naLehtyfitnediotdesulebalretcarahc-04A

ehtnisrebmunfospuorg3tsalehterazzdna,yy,xxerehW .sserddaCAM=egnaR sretcarahc*?;{(\/ton-sretcarahcciremunahpla04

tonsitluafednehW.elbatius

--tenrehtEpi

eludoM

retuoRtluafeD sserddanoitanitsedehtfitneserasegassemhcihwotretuorehtfosserddaPIehTemasehtnoretuorafosserddaPIehtottesebdluohstI.tenbuslacolehtnotonsiotsirotcelloCEYEQIehtfideificepsebtsumtI.rotcelloCEYEQIehtsatenbusdesuebotsisCNClautrivehtfoenofiro,sretuorsnapstahtkrowtenretninadliub

.retuorafoedisrehtoehttenbustenrehtEnaotdetcennocCPayberehtfI.revresPCHDamorfdeniatbositideificepssignisserddacitamotuanehW

.testonsitignitarepotonsitirorevresPCHDonstluafedtiesacsihtni,denifedyllaunamebtsumtidetcelessignisserddalaunamfI

.0.0.0.0ot552.552.552.552ot0.0.0.0=egnaR

launamnehWgniebsignisserdda

.desu




Configure Addressing Details with IP Tool (Continued)13IQ EYE Collector Data SheetTA200998IP Tool Manual TE200638

Note that when setting up the Ethernet addressing ensure that there is only one subnet on a network segment.

retemaraP noitpircseD egnahcotnehW-tenrehtE

pieludoM

PCHD .desusignisserddalaunamrocitamotuarehtehwseificepSPIs'rotcelloCEYEQIehtdeificepssignisserddacitamotuanehWerasretemaraprevresSNIWdna,retuortluafed,ksamtenbus,sserddatonsitirorevresPCHDonerehtfI.revresPCHDamorfdeniatbo

ehtnosecivedrehtoehthtiwdetaitogenotuasisserddaPIehtgnitarepo0.0.552.552ottessiksamtenbusPIehtdna,tenbusemas

,sserddaPIs'rotcelloCEYEQIehtdetcelessignisserddalaunamfIebtsumsretemaraprevresSNIWdna,retuortluafed,ksamtenbus

.denifedyllaunam.seY=tluafeD,desuPCHD=seY,oNroseY=egnaR

otsiedomgnisserddanehW.degnahceb

ebnacgnisserddalaunaMahtiwmetsysanodesuQIehtgedivorprevresPCHDsisserddas'rotcelloCEYEybdengissaegnarehtedistuo

revreseht

emantsoH emankrowtenehthtiwderetsigersitahtgnirtsretcarahc-51A)ylno/daer(trehtaremanybgnitcennocrofrevres serddaPInah

spuorg3tsalehterazzdna,yy,xxerehW.zz_yy_xx_DNERTotstluafedtIehtnisrebmunfo .sserddaCAM

=egnaR sretcarahc*?;{(\/ton-sretcarahcciremunahpla51

.elbatiustonsitluafednehW

sserddAPI ehtnoecivedhcaerofsserddaPIehT.sserddaPIehT)etirw/daer(.sehsalcsserddadiovaoteuqinuebtsumkrowtentenrehtE

PCHDamorfdeniatbositideificepssignisserddacitamotuanehWdetaitogenotuasitignitarepotonsitirorevresPCHDonerehtfI.revres

.tenbusemasehtnoseivedrehtohtiwesacsihtni,denifedyllaunamebtsumtidetcelessignisserddalaunamfI

.0.0.0.0otstluafedti552.552.552.552ot0.0.0.0=egnaR

signisserddalaunamnehW.desugnieb

revreSSNIW .revreSSNIWehtfosserddaPIehtseificepS)etirw/daer(PCHDamorfdeniatbositideificepssignisserddacitamotuanehW

.testonsitirorevresPCHDonerehtfI.revresesacsihtni,denifedyllaunamebtsumtidetcelessignisserddalaunamfI


signisserddalaunamnehWotnoitcennocdna,desugniebsisemantsohgnisusecived

.deriuqer

ksaMtenbuS llarofemasehtebtsumksamtenbusti,ksamtenbusehT)etirw/daer(narosnaLdliuboteratahtsretuorybdetarapestonsecived

.tenbusemasehtnoerayehttahtserusnesihT.krowtenretniPCHDamorfdeniatbositideificepssignisserddacitamotuanehW

.0.0.0.0ottessitirevresPCHDonerehtfI.revresesacsihtni,denifedyllaunamebtsumtidetcelessignisserddalaunamfI


signisserddalaunamnehW.desugnieb

troPPDU otdesutrop)locotorPmargataDresU(PDUehT)etirw/daer(.krowtentenrehtEehtrevosecivedmetsysQIrehtohtiwetacinummocstluafeD.tropemasesutsumkrowtenretninaetaercotdesusecivedllA

.21675ot53556ot0=egnaR

elbatiustonsitluafednehWrodesugniebydaerlatropg.e)setis(skrowtenretnielpitlum

.tenbusemasehtnoderiuqer

etomeRCNIE

seludoM

sserddAPI .tenrehtEnoecivedetomerehtfoemantsoh/sserddaPIehT)etirw/daer(.tenrehtEnoecivedetomerehtfosserddaPIroemantsohehT

0.0.0.0=tluafeD.552.552.552.552ot0.0.0.0=egnaR

tliubebotsikrowtenretnifIowttsaeltA.sretuorssorcahcaehcaemorfsecived

.deficepsebdluohstenbusksamtenbuS ot0.0.0.0=egnaR.ecivedetomerehtrofksamtenbusehT)etirw/daer(0.0.0.0=tluafeD552.552.552.552

secivedlanoitiddafosliatedytilibailerdesaercniroF.deficepsebdluohstenbushcaehcaemorfsecivedowttsaeltAlaunamfidna,semantsohgnisudeificepsebtsumsecivedehtdesugniebsignisserddacitamotuafI.deificepsebdluohs

nidecalpebtsumelbatehT.sesserddaPItsewolehthtiwsecivedehtniatnocdluohstsilehtdesugniebsignisserdda.krowtenehtnosecivedlla

lautriVCNC

seludoM

PImralAsserddA

sitahtrosivrepustegratmralaehtfosserddaPIroemantsohehTgnitteS.edommralanignitarepofikrowtentenrehtEehtotdetcennoclautrivehtstneverpdna,edommralaotniCNClautrivehtsehctiwspusiht

CNClautrivehthctiwslliw0.rosivrepusaybCNCasadesugniebCNCdesunU=tluafeD.edomrosivrepusotnikcab

desuebotsiCNClautrivehtfIrosivrepusaotsmraladnesot

.tenrehtErevo

sserddACNC sitI.naLs’rotcelloCEYEQInoCNClautrivehtfosserddaecivedehTstilitnuetarepotonlliwCNClautrivehtdna,tluafedybdesunuottesgnidulcxe911ot1(sserddadilavynaottesebnactI.putessisserdda

.CNClautrivehtelbasidlliw0.)01dna,3,2sesserdda

.desuebotsiCNClautrivehtfI

sserddAtroP dnatluafedybdesunutessitI.CNClautrivehtybdesutropPCTehTsisserddacncehtnehwsserddacncehtsulp00001otstluafedneht

.76723ot1=egnaR.degnahcebyltneuqesbusnactub,putes

.desuebotsiCNClautrivehtfI



14a Enter configuration mode using SET. The top level

prompt will be displayed as below.b Configure the optional settings the relevant upper

case letter and pressing ENTER. If a value has beenchanged X+ENTER will confirm it and return to thetop menu, whereas Q+ENTER will quit and returnwith the value unchanged. The table on the nextpage describes the settings.

SET Manual TE200147

Configure Optional Settings Using SET

Note that it may be necessary to set up a virtual CNC in the IQEYE Collector if one is not available elsewhere on the network.

IQ EYE Collector Data Sheet TA200998


Note that if required the parameters configured using IP Tool can also be configured in the same way.

retemaraP noitpircseDsserddA

eludoMmralAnaL

sserddAtinehwkrowtenpooltnerrucehtybdetarenegsmralarofsserddaecivedtegratmralaehT)etirw/daer(

0.)01dna,3,2sesserddagnidulcxe911ot1(sserddadilavynaottesebnactI.naLasagnitareposi.dettimsnartgniebsmralaehtspots

mralAnaLnaL

gnitarepositinehwkrowtenpooltnerrucehtybdetarenegsmralarofrebmunnaLtegratehT)etirw/daer(ehtspots0.)01dna,3,2sesserddagnidulcxe911ot1(sserddadilavynaottesebnactI.naLasa

.dettimsnartgniebsmralamralA

egaugnaL,hsidewS=3,hsinniF=2,hsinapS=1,hsilgnE=0.smralakrowtenehtrofdesuegaugnalehT)etirw/daer(

.hcnerF=9,eseugutroP=8,nailatI=7,namreG=6,hsinaD=5,naigewroN=4emaNtsoH emanybgnitcennocrofrevresemankrowtenehthtiwderetsigersitahtgnirtsretcarahc51A)etirw/daer(

.sserddaPInahtrehtarkrowtenretnI

mralAsserddA

sserddadilavynaottesebnactI.smralakrowtenretnirofsserddaecivedtegratmralaehT)etirw/daer(.dettimsnartgniebsmralaehtspots0.)01dna,3,2sesserddagnidulcxe911ot1(

krowtenretnInaLmralA

1(sserddadilavynaottesebnactI.smralakrowtenretnirofrebmunnaLtegratmralaehT)etirw/daer(.dettimsnartgniebsmralaehtspots0.)01dna,3,2sesserddagnidulcxe911ot

elbasiDevilACNCv

smralA

,oNroseY=egnaR.sCNClautrivybdetarenegsmraladaedeciveddna,enil-noecivedselbasid/selbanE.oN=tluafeD.delbasidsmrala=seY

etomeRseciveD

dneSetomeR

stsacdaorB

krowtenretniehtdliubotdesuerasegassemdetceridrosegassemtsacdaorbetomerrehtehwseificepS.sretuorssorca

sretuorssorcakrowtenretniehtdliubotdesusegassemeht)seY(segassemtsacdaorbesuottesfIetomerehtnosecivedllaotegassemtsacdaorbagnitseuqerretuortluafedehtottneseblliw

.eludomehtnideificepsecivedetomerehtsallewsatenbuss’ecivedsretuorssorcakrowtenretniehtdliubotdesusegassemeht)oN(segassemtsacdaorbesuottontesfI

.eludomehtnideificepsecivedehtot)gnigassemtceridyb(tnesebylnolliw.delbasidgnigassemtsacdaorbetomerevahsretuorehtfiffodenrutebylnodluohsnoitposihT

deretneebdluohstenbushcaemorfelbissopsas’ecivedynamsafosliated,ffodenrutsignitsacdaorbfI.eruliafafotneveehtnitliubebotkrowtenretniehtelbaneotelbatsecivedetomerehtni

etadpUetomeRseciveD

ruoyypoCCNIEetomer

rehtoottsilsCNIE)N/Y(

tsilniCNIEdnasL/CNIEhtiwstenbuslladnatenbuslacolottsilscniEetomerehtseipoC

resUseludoM

NIP tnesebtsumro,yalpsidamorfnogolotresuehtybderetneebtsumtahtrebmuntigid-4ehT)etirw/daer(.egnahcaesirohtuaotrosivrepus/lootayb

pi-tenrehtEeludoM

gnikrowteNdelbasiD

.krowtentenrehtEehtnoseciveddnerTrehtorofhcraeslliwecivedehtrehtehwseificepS

klatnoLeludom

klatnoLdelbanE

sinoitcennocnoLfidelbasidebTSUMsihT.snoitacinummocskroWnoLsecivedehtselbasid/selbanE.desugniebton



1 2 3 4 5 6 7 8 9 10


Tear off Label Strip16XTEND -400007096� � � � � � �

�

� � � � � 00.10.70.00.UD.BB

� � �

S/No:

� � � � � � � Location

� � � � � 00.10.70.00.UD.BB

S/No:Q3B____X73010003

� � � � � � �

� � � � � 00.10.70.00.UD.BB S/No:Q3B____X73010003

� � � � � � � Location

Replace Cover17 a

b

18 Configure Data Collection

Run SET and use the IQ EYE Wizard to Configure the datacollection as described in the IQ EYE Wizard Manual(TE200999)

IQ EYE Wizard Manual TE200999

19If alarm data is to be collected it is necessary to configurealarms to be sent to the IQ EYE Collector. This can bedone by using 963 to retransmit alarms to the IQ EYECollector see the IQ EYE Wizard Manual (TE200999), orby configuring the IQ controllers to send their alarms (intext format) directly to the IQ EYE Collector see the SETManual (TE200147).

IQ EYE Wizard Manual (TE200999)SET Manual (TE200147)

Configure Alarm Handling

1 2 3 4 5 6 7 8 9 10

Write on Label15 �

� � � � � 00.10.70.00.UD.BB

� � �

S/No:Q3B____X73010003

� � � � � � � Location

� � � � � 00.10.70.00.UD.BB

S/No:Q3B____X73010003XTND -400007096

� � � � � � �

� � � � � � �

recommendede.g. location/identifier

IP Address, Location, Lan, address



Check Communications




Internetwork(on LON)

EINC

EINC

4 5 64 5 6

2

7 8 97 8 9

3

10 11 1210 11 12

4

13 14 1513 14 15

5

16 17 1816 17 18

6

19 20 2119 20 21

7

22 23 2422 23 24

8

25 26 2725 26 27

9

28 29 3028 29 30

10+ 0+ 0+ 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0+ 0+ 0+ 0+ 0+ 0+ 0

1 2 31 2 3

1+ 0+ 0

0V

24V

24V

34 35 3634 35 36

12

37 38 3937 38 39

13

40 41 4240 41 42

14A

31 32 3331 32 33P

11

43 44 4543 44 45

15

46 47 4846 47 48

16100-240 V100-240 V

OK RXOK RX

P 0 P 0 P 0P 0 P 0 P 0

OK

Tx Rx

230 V1 2 3 4 5 6 83 4 5

7 9 10 1124V 24V

AC

24V

AC

24V

AC

IQL


INC

IQ EYE Collector



IQ EYE Collector



EINC

EINC

4 5 64 5 6

2

7 8 97 8 9

3

10 11 1210 11 12

4

13 14 1513 14 15

5

16 17 1816 17 18

6

19 20 2119 20 21

7

22 23 2422 23 24

8

25 26 2725 26 27

9

28 29 3028 29 30

10+ 0+ 0+ 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0+ 0+ 0+ 0+ 0+ 0+ 0

1 2 31 2 3

1+ 0+ 0

0V

24V

24V

34 35 3634 35 36

12

37 38 3937 38 39

1313

40 41 4240 41 42

14A

31 32 3331 32 33P

11

43 44 4543 44 45

15

46 47 4846 47 48

1616100-240 V100-240 V

OK RXOK RX

P 0 P 0 P 0P 0 P 0 P 0

OK

Tx Rx

230 V1 2 3 4 5 6 83 4 5

7 9 10 1124V 24V

AC

24V

AC

24V

AC

IQL

20

If address=>100

If address <100





EINC

EINC

4 5 64 5 6

2

7 8 97 8 9

3

10 11 1210 11 12

4

13 14 1513 14 15

5

16 17 1816 17 18

6

19 20 2119 20 21

7

22 23 2422 23 24

8

25 26 2725 26 27

9

28 29 3028 29 30

10+ 0+ 0+ 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0+ 0+ 0+ 0+ 0+ 0+ 0

1 2 31 2 3

1+ 0+ 0

0V

24V

24V

34 35 3634 35 36

12

37 38 3937 38 39

13

40 41 4240 41 42

14A

31 32 3331 32 33P

11

43 44 4543 44 45

15

46 47 4846 47 48

16100-240 V100-240 V

OK RXOK RX

P 0 P 0 P 0P 0 P 0 P 0

OK

Tx Rx

230 V1 2 3 4 5 6 83 4 5

7 9 10 1124V 24V

AC

24V

AC

24V

AC

IQLIQ EYE Collector





EINC

EINC

4 5 64 5 6

2

7 8 97 8 9

3

10 11 1210 11 12

4

13 14 1513 14 15

5

16 17 1816 17 18

6

19 20 2119 20 21

7

22 23 2422 23 24

8

25 26 2725 26 27

9

28 29 3028 29 30

10+ 0+ 0+ 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0+ 0+ 0+ 0+ 0+ 0+ 0

1 2 31 2 3

1+ 0+ 0

0V

24V

24V

34 35 3634 35 36

12

37 38 3937 38 39

13

40 41 4240 41 42

14A

31 32 3331 32 33P

11

43 44 4543 44 45

15

46 47 4846 47 48

16100-240 V100-240 V

OK RXOK RX

P 0 P 0 P 0P 0 P 0 P 0

OK

Tx Rx

230 V1 2 3 4 5 6 83 4 5

7 9 10 1124V 24V

AC

24V

AC

24V

AC

IQLIQ EYE Collector





EINC

EINC

4 5 64 5 6

2

7 8 97 8 9

3

10 11 1210 11 12

4

13 14 1513 14 15

5

16 17 1816 17 18

6

19 20 2119 20 21

7

22 23 2422 23 24

8

25 26 2725 26 27

9

28 29 3028 29 30

10+ 0+ 0+ 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0+ 0+ 0+ 0+ 0+ 0+ 0

1 2 31 2 3

1+ 0+ 0

0V

24V

24V

34 35 3634 35 36

12

37 38 3937 38 39

13

40 41 4240 41 42

14A

31 32 3331 32 33P

11

43 44 4543 44 45

15

46 47 4846 47 48

16100-240 V100-240 V

OK RXOK RX

P 0 P 0 P 0P 0 P 0 P 0

OK

Tx Rx

230 V1 2 3 4 5 6 83 4 5

7 9 10 1124V 24V

AC

24V

AC

24V

AC

IQL


INC

IQ EYE Collector





EINC

EINC

4 5 64 5 6

2

7 8 97 8 9

3

10 11 1210 11 12

4

13 14 1513 14 15

5

16 17 1816 17 18

6

19 20 2119 20 21

7

22 23 2422 23 24

8

25 26 2725 26 27

9

28 29 3028 29 30

10+ 0+ 0+ 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0 + 0+ 0+ 0+ 0+ 0+ 0+ 0+ 0

1 2 31 2 3

1+ 0+ 0

0V

24V

24V

34 35 3634 35 36

12

37 38 3937 38 39

13

40 41 4240 41 42

14A

31 32 3331 32 33P

11

43 44 4543 44 45

15

46 47 4846 47 48

16100-240 V100-240 V

OK RXOK RX

P 0 P 0 P 0P 0 P 0 P 0

OK

Tx Rx

230 V1 2 3 4 5 6 83 4 5

7 9 10 1124V 24V

AC

24V

AC

24V

AC

IQL


INC

IQ EYE Collector

21 Check Virtual CNCs Virtual CNCs in Alarm Mode

Ethernet

CNCBCNCA

IQ EYE Collector

CNCDCNCC

SET, or 963using permanentconnection

CNC inSupervisor mode

CNCFCNCE CNCHCNCG

Virtual CNCs in Supervisor Mode

Ethernet

CNCBCNCA

IQ EYE Collector

CNCDCNCC

963using temporaryconnection

CNC inAlarm mode

CNCFCNCE CNCHCNCG

Alarm from system sent to VCNC




1 2 3 41 2 3 4

RS232 RxTx

OK

OK LON

1 21 2

28-36 V24 V ETHERNET

TREND LANTREND LAN


LON

OK

LON

OK

LON

TERM

LON

TERM


SRV PINSRV PIN

1 2 3 4 5 6 7 8 9 10

1 2 3 41 2 3 4

RS232 RxTx

OK

OK LON

1 21 2


TREND LANTREND LAN


LON

OK

LON

OK

LON

TERM

LON

TERM


SRV PINSRV PIN

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

O

I

Switch Off1

2 REPLACING A FUSE

Remove Cover2

WARNING: Opening the panel may exposedangerous voltages.417-IEC-5036

Caution: This unit contains static sensitive devices.Suitable anti-static precautions should betaken throughout this operation to preventdamage to the units.

ab

c

WARNING: The connecting leads may beconnected to supplies. Isolate beforetouching.

BS EN100015/1 Basic Specification: protection of electrostaticsensitive devices.

Replace Mains Supply Fuse4

ab c

Unplug Power Connector3

125 mA20 mm anti-surge

Disconnect from mains



1 2 3 4 5 6 7 8 9 10

2 REPLACING A FUSE (Continued)

Replace Cover6a

b

�

�

Switch On7

Reconnect Power Connector5

1 2 3 41 2 3 4

RS232 RxTx

OK

OK LON

1 21 2


TREND LANTREND LAN


LON

OK

LON

OK

LON

TERM

LON

TERM


SRV PINSRV PIN

1 2 3 4 5 6 7 8 9 10



3 END USER LICENCE AGREEMENTEULA Terms

• You have acquired a IQ EYE Collector (“Device”) that includes software licensed by Trend Control Systems Ltd from one or moresoftware licensors (“Trend Control Systems Ltd Software Suppliers”). Such software products, as well as associated mediaprinted materials and “online” or electronic documentation (“SOFTWARE”) are protected by international intellectual propertylaws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.”

• IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPY THESOFTWARE. INSTEAD, PROMPTLY CONTACT TREND CONTROL SYSTEMS LTD FOR INSTRUCTIONS ON RETURN OFTHE UNUSED DEVICE(S) FOR A REFUND. ANY USE OF THE SOFTWARE INCLUDING BUT NOT LIMITED TO USE ON THEDEVICE WILL CONSTITUTE YOUR AGREEMENT TO THE EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT).

• GRANT OF SOFTWARE LICENSE. This EULA grants you the following license:

• You may use the SOFTWARE only on the DEVICE

• NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT. TREND CONTROL SYSTEMS LTD HASINDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND TREND CONTROL SYSTEMSLTD’S SOFTWARE SUPPLIERS HAS RELIED UPON TREND CONTROL SYSTEMS LTD TO CONDUCT SUFFICIENTTESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE.

• NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided “AS IS” and with all faults. THE ENTIRE RISKAS TO SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE)IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THESOFTWARE OR AGAINST INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICEOR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, TRENDCONTROL SYSTEMS LTD’S SOFTWARE SUPPLIERS.

• Note on Java Support. The SOFTWARE may contain support for programs written in Java. Java technology is not faulttolerant and is not designed, manufactured, or intended for use or resale as online control equipment in hazardousenvironments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communicationsystems, air traffic control, direct life support machines, or weapons systems, in which the failure of Java technology couldlead directly to death, personal injury, or severe physical or environmental damage. Sun Microsystems, Inc. has contractuallyobligated Trend Control Systems Ltd’s software suppliers to make this disclaimer.

• No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW, TREND CONTROL SYSTEMS LTD’S SOFTWARESUPPLIERS SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTALDAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE. THISLIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALLTREND CONTROL SYSTEMS LTD’S SOFTWARE SUPPLIERS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S.TWO HUNDRED FIFTY DOLLARS (U.S.$250.00).

• Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile,or disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable lawnotwithstanding this limitation.

• SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under this EULAonly as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EULA. If the SOFTWAREis an upgrade, any transfer must also include all prior versions of the SOFTWARE.

4 LIMITATIONS OF USEApprovals

The CE and UL Approvals are defined in the Specification (Environmental) section of the IQ EYE Collector Data Sheet (TAxxxxxx).

GeneralHost Equipment: The IQ EYE Collector baseboard host fully complies with the requirements necessary for the EC24 modemregulatory requirements if it is operated within the specification defined in the IQ EYE Data Sheet(TAxxxxxx). The modemis supplied to be used solely within the IQ EYE Collector.

Safety: The modem comprises two sections of circuitry, namely a telecommunications interface and a host interface, whichare separated by a safety barrier that meets the reinforced level of isolation at 250Vrms. The modem cannot be used in hostequipment that use or generate voltages in excess of 250 Vrms.

The telecommunications interface is approved to be connected to telecommunication network voltage circuits which maycarry dangerous voltages. The telephone cord must remain disconnected from the telecommunications systems until theMT5600SMI-L-92 modem has been installed within a host which provides the necessary protection for the operator. If it issubsequently desired to open the host equipment for any reason, the telephone cord must be disconnected prior to effectingaccess to any internal parts which may carry telecommunication network voltages.

The integrity of the telephone line cord, connected to the modem, should not be compromised by wear or proximity tohazardous voltages, as defined by EN60950.



4 LIMITATIONS OF USE (Continued)

GeneralThe modem RJ11 PSTN network connector port type is TNV-3.

The local environment within the host must not be subject to conductive pollution or to dry non-conductive pollution whichcould become conductive due to condensation.

Power is supplied to the modem through the host interface connector.

Network: External control software for this unit must comply with the following requirements. No other modes of operationshould be used on the PSTN and the use of such modes invalidates the approval.

1. It must not allow the “S” register values to be set outside the following ranges: S6 (delay for blind dialling): 4 only,ie default value.

2. When dialling out, the number of “,” pauses inserted between digits in a dialled number must not exceed 5.

The modem is suitable for connection to PSTN direct exchange lines and/or to an approved private branch exchange. It maybe connected to any PSTN direct exchange line except as an extension to a pay-phone, or shared service.

The modem has a REN (ringer equivalence number) of 0.1B. The REN is a customer guide indicating the maximum numberof items of apparatus that should be connected simultaneously to the line. The total REN value must not exceed the maximumREN value of 4.

Country Specific InformationUSAFCC Part 15 Regulation

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Theselimits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1) This devicemay not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation.

WARNING – Changes or modifications to this unit not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.

47 CFR Part 68 Telecom1. This equipment complies with Part 68 of the 47 CFR rules and the requirements adopted by the ACTA. Located on

this equipment is a label that contains, among other information, the registration number and ringer equivalencenumber (REN) for this equipment or a product identifier in the format:

The registration number is AU7/USA-46014-MD-EThe REN is 0.1B

REN: For Canada the sum of the RENs of all the devices must not exceed five”.

The jack plug used to connect the IQ EYE Collector to the premises wiring and telephone network is RJ11, which complieswith the applicable 47 CFR part 68 rules and requirement adopted by the ACTA.

CanadaRegulatory Requirements for Canada

The following requirements are established under section 69.3 of the Telecommunications Act for purposes of section 5 ofthe Telecommunications Apparatus Regulations.

The equipment bears the following identifying marks, which are permanently affixed to the equipment:

(a) The registration number — Specifications of this mark are given in the document: IC: 125 1142A(b) The model identification number under which the product was registered: MT5600SMI-L-92

“This product meets the applicable Industry Canada technical specifications”

The REN is 0.1B

REN: For Canada the sum of the RENs of all the devices must not exceed five”.

Industry CanadaThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel brouilleur.



WEEE Directive :

At the end of their useful life the packagingand product should be disposed of via asuitable recycling centre.Do not dispose of with normal household waste.Do not burn.

5 DISPOSAL

4 LIMITATIONS OF USE (Continued)

Country Specific InformationNew ZealandNew Zealand Telecom Warning Notice

1. The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the itemcomplies with minimum conditions for connection to its network. It indicates no endorsement of the product byTelecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctlyin all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that anyproduct is compatible with all of Telecom’s network services. This equipment is not capable under all operatingconditions of correct operating conditions of correct operation at the higher speed which it is designated. 33.6 kbpsand 56 kbps connections are likely to be restricted to lower bit rates when connected to some PSTN implementations.Telecom will accept no responsibility should difficulties arise in such circumstances.

2. Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair.3. This modem shall not be used in any manner which could constitute a nuisance to other Telecom customers.4. This device is equipped with pulse dialing, while the Telecom standard is DTMF tone dialing. There is no guarantee

that Telecom lines will always continue to support pulse dialing. Use of pulse dialing, when this equipment isconnected to the same line as other equipment, may give rise to ‘bell tinkle’ or noise and may also cause a falseanswer condition. Should such problems occur, the user should NOT contact the Telecom Faults Service. Thepreferred method of dialing is to use DTMF tones, as this is faster than pulse (decadic) dialing and is readily availableon almost all New Zealand telephone exchanges.

7. Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the host associatedwith this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom’sSpecifications:

For repeat calls to the same number: There shall be no more than 10 call attempts to the same number withinany 30 minute period for any single manual call initiation, and the equipment shall go on-hook for a period of notless than 30 seconds between the end of one attempt and the beginning of the next attempt.For automatic calls to different numbers, the equipment shall be set to ensure that automatic calls to differentnumbers are spaced such that there is no less than 5 seconds between the end of one call attempt and thebeginning of another.

8. For correct operation, total of the REN’s of all devices connected to a single line at any time should not exceed 5.

South AfricaThis modem must be used in conjunction with an approved surge protection device.

International useThe modem is approved in the UK, USA,- Australia, Austria, Belgium, Canada, China, Cyprus, Denmark, Eire, Finland,France, Germany, Greece, Holland, Hong Kong, Hungary, India, Italy, Japan, Luxembourg, New Zealand, Norway, Poland,Portugal, Russia, Singapore, Spain, Sweden, Switzerland, and many other countries. Check with Technical support for othercountries.

International Modem RestrictionsSome dialing and answering defaults and restrictions may vary for international modems. Changing settings may cause amodem to become non-compliant with national telecom requirements in specific countries. Also note that some softwarepackages may have features or lack restrictions that may cause the modem to become non-compliant.

EMC, Safety, and R&TTE Directive ComplianceThe CE mark is affixed to this product to confirm compliance with the following European Community Directives: CouncilDirective 89/336/EEC of 3 May 1989 on the approximation of the laws of Member States relating to electromagneticcompatibility; and Council Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member Statesrelating to electrical equipment designed for use within certain voltage limits; and Council Directive 1999/5/EC of 9 Marchon radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity.



This page is intentionally left blank.



Please send any comments about this or any other Trend technical publication to [email protected]

© 2008 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion ControlsDivision of Honeywell Technologies Sàrl, Ecublens, Route du Bois 3, Switzerland by its Authorized Representative, Trend Control Systems Limited.

Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof withoutobligation to notify any person of such revisions or changes.

Trend Control Systems LimitedP.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www. trend-controls.comTrend Control Systems USA6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel: (425) 897 3900, Fax: (425)869-8445 www. trend-controls.com

iq eye collector/230 installation instructions

Documents