instructions for a low-tech sink
DESCRIPTION
A project created for Greensgrow Farms in conjection with the Industrial Design department at University of the Arts. Dreamed, designed and assembled by Megan Hild and Emily Howe for their Junior studio project.TRANSCRIPT
© MHILD & EHOWE 2011
LOW—TECH SINK:
a guide to the parts and assembly of an inexpensive, simple, and mobile garden sink.
A project created for Greensgrow Farms in conjection with the Industrial Design department at University of the Arts. Dreamed, designed and assembled by Megan Hild
and Emily Howe for their Junior studio project.
YOU WILL NEED:
squeezable siliconvice gripsfix—it —stick, fix—it —stick, or another brand of epoxy puttyteflon tape
PREPARE YOUR TOOLS:
PARTS USED:
fix—it —stick, or another brand of epoxy putty
1/2" galvanized steel nipple (2x)
2 1/2" galvanized steel nipple
following manufacturers directions, fill two 1/2" nipples, and one
2 1/2" nipple. allow to set.
!!!
MAKE SURE TO TAPE ALL JOINTS WHEN ASSEMBLING
!!!
ALSO, TIGHTEN ALL JOINTS WHILE ASSEMBLING:
PARTS USED:
1/2" galvanized steel nipple (2x)
garden hose to 1/2" pipe connector
1/2" galvanized steel T —joint
1/2" galvinized steel floor flange
one nipple has epoxy plug
PARTS USED:
1/2" stainless steel self closing valve
8 x 1/2" galvanized steel pipe
30 x 1/2" galvanized steel pipe
PARTS USED:
5 x 1/2" galvanized steel pipe
12 x 1/2" galvanized steel pipe
1/2" galvanized steel elbow
26 1/4 x 1/2" galvanized steel pipe
1/2" galvanized steel T —joint
1/2" galvanized steel nipple
1/2" galvanized steel nipple
epoxy plug here
PARTS USED:
3 1/2 x 1/2" galvanized steel pipe
1/2" galvanized steel elbow (2x)
1/2" galvanized steel T —joint (2x)
2 1/2" galvanized steel nipple
epoxy plug here
INOUT
PARTS USED:
stainless steel bowl, or other basin of your choice
1/2" galvanized steel nipple (2x)
2 1/2" galvanized steel nipple
prep the basin by drilling one 1/2" drainage hole, and two 1/4" holes to
attach the flange.
PARTS USED:
1/2" galvinized steel floor flange
use silicon to seal the flange to the basin.
cover the face of the flange, position on
pre —drilled basin. attach the nuts and bolts, and seal
with more silicon.
PARTS USED:
12" x 6" x 3/4" Plywood (4x)
12" x 24" x 3/4" Plywood (2x) cont.
PARTS USED:
Large door hinge 1/4" Screws (5x) 5" metal chain
1 1/2" x 1/4" bolts (8x)
Standard wood screws (21x)
Washers (16x) 1/4" nuts (8x)
1/2" galvanized steel T —joint (5x)
8 x 1/2" galvanized steel pipe
30 x 1/2" galvanized steel pipe
1/2" stainless steel self closing valve
1/2" galvanized steel nipple (3x)
garden hose to 1/2" pipe connector
1/2" galvinized steel floor flange
5 x 1/2" galvanized steel pipe
12 x 1/2" galvanized steel pipe
26 1/4 x 1/2" galvanized steel pipe
3 1/2 x 1/2" galvanized steel pipe
1/2" galvanized steel elbow (3x)
2 1/2" galvanized steel nipple