Installation

Viking Range Corporation111 Front Street

Greenwood, Mississippi 38930 USA(662) 455-1200

For product information, call 1-888-VIKING1 (845-4641)or visit the Viking Website at vikingrange.com

F20946A EN (062512)

Built-In Electric 30”Single and Double Ovens

IMPORTANT• Before beginning installation, read these

instructions thoroughly and carefully.

• DO NOT remove permanently affixedlabels, warnings or plates from theproduct as this may void the warranty.

• Observe all local and national codes,requirements and ordinances.

• Installation must conform with local codesor in the absence of codes, the NationalElectrical Code, ANSI/NFPA-70 – latestedition, or Canadian Electrical Code, CSAC22.1-1982 and C22.2 No. 01982 – latestedition, National Fuel Gas CodeANSIZ223.1/NFPA-54 – latest edition andall local codes and ordinances.

• IN MASSACHUSETTS: This appliance mustbe installed by a Massachusetts licensedplumber or electrician.

• IN CANADA: Installation must be inaccordance with the current CSA C22.1Canadian Electrical Codes Part 1 and/orlocal codes.

• Installers should leave these instructionswith the consumer who should retain themfor the local inspector’s use and for futurereference.

3

– Please Read and Follow

Your safety and the safety of others isvery important.

We have provided many important safetymessages in this manual and on yourappliance. ALWAYS read and obey allsafety messages.

This is the safety alert symbol. Thissymbol alerts you to hazards thatcan kill or hurt you and others.

All safety messages will be preceded bythe safety alert symbol and the word“DANGER,” “WARNING” or “CAUTION.”These words mean:

Hazards or unsafe practiceswhich WILL result in severe personal

injury or death

DANGER

Hazards or unsafe practiceswhich COULD result in severe personal

injury or death

Hazards or unsafe practices whichCOULD result in minor personal injury

or property damage.All safety messages will identify the

hazard, tell you how to reduce the chanceof injury, and tell you what can happen if

the instructions are not followed.

WARNING

CAUTION

Table of Contents

Warnings & Important Safety Information_______________________________________________3Dimensions _________________________________________________________________________5Specifications _______________________________________________________________________6Cutout Dimensions __________________________________________________________________7Flush Mount Installation ______________________________________________________________8Electrical Requirements _____________________________________________________________10General Information ________________________________________________________________11Installation_________________________________________________________________________12Final Preparation ___________________________________________________________________15Performance Checklist ______________________________________________________________16Service & Registration_______________________________________________________________18

Site Preparation: It is recommended that a thorough site inspection be conducted PRIOR tounpacking and moving this appliance.

Note: Wiring diagram is located on top of oven or in control panel.

Dimensions

5

IMPORTANT

4

– Please Read and Follow

WARNINGThe misuse of the oven door(s) (e.g.stepping, sitting, or leaning on them) canresult in hazards or injuries and damageto the product.

WARNINGELECTRICAL GROUNDINGINSTRUCTIONSThis oven must be electrically grounded inaccordance with local codes or, in theabsence of local codes, with the NationalElectrical Code, ANSI/NFPA-70 – latestedition.

WARNINGFrame grounded by a 4-conductor cableassembly. See installation section.

DO NOT USE AN EXTENSION CORDWITH THIS APPLIANCE. SUCH USE MAYRESULT IN FIRE, ELECTRICAL SHOCKOR OTHER PERSONAL INJURY.

WARNINGThis appliance should not be used forspace heating. This information is basedon safety considerations.

WARNINGThe use of cabinets for storage above theoven may result in potential fire or burnhazard.

CAUTIONThe oven is heavy—use extreme carewhen handling.

51-3/8”(130.5 cm)

51-3/8”(130.5 cm)

51-3/8”(130.5 cm)

25-3/16”

(64.0 cm)25-3/16”

(64.0 cm)

29-3/4”(75.6 cm)

29-3/4”(75.6 cm)

29-3/8”(74.6 cm)

23-1/2”(59.7 cm)

46-3/16”(117.3 cm)

21-1/4”(53.9 cm)

30” Single Oven 30” Double OvenWARNINGDO NOT use the handle or oven door tolift the oven. Remove door beforeinstallation to ensure that it is not used tolift the unit. See installation section fordoor removal.

Cutout Dimensions(For standard installation and flush mount* installations)

7

Specifications

6

30"W. Electric Single/DoubleDescription RDSOE306 RDDOE306

Overall width 29-3/4” (75.6 cm)

Overall height 29-3/8” (74.6 cm) 51-3/8” (130.5 cm)

Overall depth To front of door 25-3/16” (64.3 cm)

Cutout width Standard—28-1/2” (72.4 cm minimum)Flush mount*—29-5/8” (75.25 cm)

Cutout height Standard—28-1/4” (71.8 cm)Flush mount*—29-1/2” (74.9 cm)

Standard—50-5/8” (128.6 cm)Flush mount*—51-1/2” (130.8 cm)

Cutout depth Standard—24” (61.0 cm)Flush mount*—25-1/4” (64.1 cm)

Electrical requirements 4-wire ground, 240 VAC, 30 amp electrical connection for single ovens/50 amp for double ovens. Unit is equipped with No. 10 ground wire in conduit.

Should be fused separately.Maximum amp usage 23.3 amps—240 VAC

20.2 amps—208 VAC46.7 amps—240 VAC40.5 amps—208 VAC

Oven interior width 25” (63.5 cm)

Oven interior height 16” (40.6 cm)

Oven interior depth 18-1/2” (50.0 cm)

Oven volume (measuredto AHAM Standard)**

3.8 cu. ft.

Oven volume (total ovencavity) 4.3 cu. ft.

*Note: To install the oven in a flush mount application the flush mount accessory kit (D30FTSfor single ovens and D30FTD for double ovens) is required.

**Note: The AHAM Standard for measuring oven capacity subtracts the door plug andconvection baffle dimension from the total oven volume.

28-1/2”

(72.4 cm)

Flushmount

29-5/8”

(75.2 cm)

24”(61.0 cm)Flush mount25-1/4”(64.1 cm)

28-1/4”(71.8 cm)Flush mount29-1/2”(74.9 cm)

5” min.(12.7 cm)

Junction boxlocation 17”(43.2 cm)

28-1/2”

(72.4 cm)

Flushmount

29-5/8”

(75.2 cm)

28-1/4”

(71.8 cm)

Flushmount

29-1/2”

(74.9 cm)24”(61.0 cm)Flush mount25-1/4”(64.1 cm)

28-1/2”

(72.4 cm)

Flushmount

29-5/8”

(75.2 cm)

50-5/8”

(128.5 cm)

Flushmount

51-1/2”

(130.8 cm)

15-1/4”

(38.7 cm) min.

tofloor

4”

(10.2 cm)

5” min.(12.7 cm)

Junction boxlocation

4-3/4”

(12.1 cm)

(Floor tobotto

m

of cutout)

5” min.(12.7 cm)

Junction boxlocation

4”

(10.2 cm)

24”(61.0 cm)Flush mount25-1/4”(64.1 cm)

4”(10.2 cm)

30” Single Oven Built-In30” Double Oven Built-In

30” Single Oven Undercounter

*Note: To install the oven in a flush mount application the flush mount accessory kit(D30FTS for single ovens and D30FTD for double ovens) is required.

Dimensions (Flush mount installation)

9

Dimensions (Flush mount installation)

8

FLUSH CUTOUTD 29-5/8” (75.2 cm)

E 25-1/4” (64.1 cm)

F 29-1/2” (74.9 cm)

FinishedSurfaces

VerticalBlocking

BA

C

FLUSH CUTOUTA 29-5/8” (75.2 cm)

B 25-1/4” (64.1 cm)

C 51-1/2” (130.8 cm)

FinishedSurfaces

VerticalBlocking

ED

F

LEGEND

Blocking

FinishedSurfaces

ScrewScrew

VerticalBlocking

Distance will varydepending on thecabinet

A

B

Top View

CRITICALDIMENSIONS

A 28-1/2” (72.4 cm)

B 1-1/2” (3.8 cm)

*Note: To install the oven in a flush mount application the flush mount accessory kit (D30FTSfor single ovens and D30FTD for double ovens) is required.

General Information• All openings in the wall behind the

appliance or in the floor under theappliance should be sealed.

• Keep appliance area clear and free fromcombustible materials, gasoline and otherflammable vapors.

• Disconnect the electrical supply prior toservicing or cleaning.

• When removing the appliance for cleaningor service, disconnect AC power supplyand carefully remove the appliance bypulling forward.

• Electrical requirements are listed in theproduct specifications under the electricalrequirements section.

Recommendations for Unpacking• Products are shipped on pallets with foam

footings and corrugated inner-packingand exterior hoods.

• Products are anchored to the pallet usingmetal straps that are screwed to thebottom of the product and the pallet.

• DO NOT remove protective packaginguntil you are ready to perform theinstallation.

• To remove the packaging, first remove thestaples located at the bottom perimeterof the corrugated cover.

• Remove the corrugated cover by liftingit off the product and remove the inner-packing.

• Detach the product from the metal anchorstrip by removing the attachment screw.

• DO NOT remove the protective wrappingfrom the product control panel until theproduct is installed.

Recommendations for Moving

• Only proper equipment should be used tomove products.

• ALWAYS take steps to protect flooring atthe installation location when movingproducts.

11

WARNINGDO NOT use the handle or oven doorto lift the oven. Remove door beforeinstallation to ensure that it is not used tolift the unit. DO NOT lift or carry the doorby the handle.

CAUTIONThe oven is heavy—use extreme carewhen handling.

Electrical Requirements• Oven requires a separate, grounded

4-wire, 240V (AC), 30 amp (single ovens)and 50 amp (double ovens) service withits own circuit breaker.

• Wire sizes and connections must conformwith the rating of the appliance and to therequirements of the National ElectricalCode, ANSI/NFPA-70 – latest edition, orCanadian Electrical Code, CSAC22.1-1982 and C22.2 No. 01982 –latest edition, and all local codes andordinances.

• Oven must be connected to the properelectrical voltage and frequency asspecified on the model/serial rating plate(located inside the vent ont the right sodeof the oven).

• Oven must be connected to groundedmetal permanent wiring system. Checkwith a qualified electrician to make surethe oven is properly grounded.

• DO NOT ground to a gas pipe.

• DO NOT use an extension cord with thisappliance, because this may result inelectrical shock or other personal injury.

• This unit is equipped with a No. 10ground wire in the conduit.

• The electrical conduit must be kept to thetop left for a flush installation. NEVER cutthe conduit.

• Connect the flexible armored cabledirectly to 4-wire, 240V household service.If codes permit and separate groundingwiring is used, we recommend that aqualified electrician determine thegrounding path and that the wire gauge isin accordance with local codes.

• Junction boxes installed on rear walldirectly behind oven must be recessed .

• A UL-Listed conduit connector must beprovided at the junction box.

• DO NOT install a fuse in the neutral orgrounding circuit. We recommend a time-delayed fuse or circuit breaker. Connectdirectly to the fused disconnect (or circuitbreaker box) through flexible armored, ornon-metallic sheathed, copper cable (withgrounding wire).

10

13

3 4

Close the door until it stops. Push in/lift door up/and then out. Repeat for all doors.

5 6

Remove racks. Unscrew pallet screws from side of oven.

Neutral GreenWhite

Black

Red

7a

Neutral

Green

White

Black

Red

7b

Wiring option 1*(connect the white and green to the incoming neutral)

Wiring option 2*(connect the white to the incoming neutral,

attach green to grounded junction box)

Installation (cont.)

*Note: Check local code to see which wiring option should be used when grounding the unit.

12

1

1

2

2

Remove wooden brace on front of pallet. Open door completely. Rotate doorhinge to unlocked position.

Installation

General InformationSite PreparationNote: It is recommended that a thoroughsite inspection be conducted PRIOR tounpacking and moving this appliance.

• Confirm available access to adequatepower—see electrical requirements.

° Single oven units require a 30 amp circuit

° Double oven units require a 50 amp circuit

• Note: A minimum of 2” spacing aboveand below the oven to any adjacent itemsis required for ventilation purposes.

• It is recommended that 3/4” or thickermaterial be utilized to create a supportplatform for this appliance.

• BE SURE that support for this appliance isperpendicular to the front facing of thewall or cabinet before you perform theinstallation.

• Use of a hydraulic lift is recommended forthe installation of double oven units. Becareful not to bend lower trim/vent.

• All openings in the wall behind theappliance or in the floor under theappliance should be sealed.

• Keep appliance area clear and free fromcombustible materials, gasoline and otherflammable vapors.

WARNINGDO NOT use the handle or oven door to liftthe oven. Remove door before installationto ensure that it is not used to lift the unit.DO NOT lift or carry the door by the handle.

WARNINGFIRE OR ELECTRICALSHOCK HAZARDDO NOT use an extension cordwith this appliance. Such usemay result in fire, electrical shockor other personal injury.

15

1

13

2

14

Open door completely. Rotate doorhinge to locked position.

Close door.

Installation

1. Some stainless steel parts may have aprotective wrap, which must be peeledoff. All stainless steel body parts shouldbe wiped regularly with hot, soapy waterat the end of each cooling period andwith liquid cleaner designed for thismaterial when soapy water will not do thejob. If build-up occurs, DO NOT use steelwool, or abrasive cloths, cleaners, orpowders. If it is necessary to scrapestainless steel surface to removeencrusted material, soak area with hot,wet towels to loosen the material, thenuse a wooden or nylon spatula or scraper.DO NOT use a metal knife, spatula, orany other metal tool to scrape stainlesssteel surfaces. Scratches are almostimpossible to remove.

2. The interior of the oven should be washedthoroughly with hot, soapy water toremove film residues and installationdebris before being used for foodpreparation, then rinsed and wiped dry.Solutions stronger than soapy water arerarely needed.

Final Preparation

14

NeutralGreen

White

Black

Red

7c 8

Wiring option 3*(connect the white to the incoming neutral,

attach green to suitable ground)

Lift oven into position.

9 10

Push oven straight in. Attach screws to the side of the framing.Note: Two screws for single ovens, four screws

for double ovens (screws not included).

11 12

Replace racks. Replace door.

Installation (cont.)

*Note: Check local code to see which wiring option should be used when grounding the unit.

Performance Checklist (cont.)

17

Performance ChecklistA qualified installer should carry out thefollowing checks:

h Check oven Bake Function—bake elementon full power, center and outside broilelements at partial power. ConvectionBake function—bake and broil elementsthe same with the convection fan “ON”.

h Check TruConvec™ function—TruConvecelement (behind convection fan cover)“ON” and convection fan “ON”.

h Check High Broil function—both broilelements at full power. Convection broilfunction is the same with convection fan“ON”.

h Check Medium Broil function—inner andouter broil elements pulse on and off.

h Check Low Broil function—inner broilelement only.

h Check Self-Clean function—Door will lockin approximately 30 seconds, the centerand outside broil elements will turn “ON”and the bake element will turn “ON” atpartial power. Check broil elementsthrough window to make sure they are“ON”, then abort self-clean cycle tounlock door.

Any adjustments necessary that are a result ofthe installer not following instructions will bethe responsibility of the installer, dealer, or theend user of the product.

16

CAUTIONDO NOT run self-clean cycle check formore than 10 minutes with the oven racksand rack supports inside oven to avoiddiscoloration due to the high temperature.

ElectronicTiming Center

Off/OnIndicator Light

InteriorOven Light Control

TemperatureControl

Self-CleanIndicator Light

Oven Function Selector

19

Notes________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

18

Service InformationIf service is required, call your dealer or authorized service agency. The name of the authorizedservice agency can be obtained from the dealer or distributor in your area.

Have the following information readily available.• Model number• Serial number• Date purchased• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are unable to obtain the name of anauthorized service agency, or if you continue to have service problems, contact Viking RangeCorporation at 1-888-VIKING1 (845-4641), or write to:

VIKING RANGE CORPORATIONPREFERRED SERVICE

1803 Hwy 82WGreenwood, Mississippi 38930 USA

Record the information indicated below. You will need it if service is everrequired. The model and serial number for your oven can be found byopening the door and looking underneath the control panel on the lefthand side.

Model no. _____________________________Serial no. ________________________________

Date of purchase ___________________ Date installed ________________________________

Dealer’s name ___________________________________________________________________

Address ________________________________________________________________________

________________________________________________________________________________

If service requires installation of parts, use only authorized parts to insure protectionunder the warranty.

Keep this manual for future reference.