GH-WPS01

Caution :Accessories 1) GBT Pump + Tank

2) Pump Power Cord

3) Velcro

4) Screws

Step1

SpecificationsPump Dimension 61x60x46mm MaximumCapacity 400L/hr Noise 20dBA Bearing CeramicBearing Lifetime 70000hr(MTBF)Tank Dimension 100x53x172mm Capacity 220cc.

1.Beforepouringliquidcoolantintothetanktotesttheliquid cooling system, please reconfirm all the tubes have been fastened and the tube clips are in the rightposition.

2.While removing the tubes for disassembly, please makesuretokeepallthedevicesawayfromanyelectronicpart.

Prepare pump power cord.

Connect the Power SW ( female 2-pin ) from the chassis’s panel to the pump power cord male 2-pin connector.

Step 2

a : PowerSW(female2-pinconnector)fromchassis’spanel

b : Pumpcordmale2-pinconnector

Step 3 Connect the pump power cord female 2-pin connector with " +PW- " jumper on the motherboard.

Connect the pump power cord 6-pin connector with the back of the tank (as Figure a / b ).

Step 4

Connect the 4-pin power supply connector to the 4-pin pump power cord.Step 5

Warning : While refilling liquid coolant, please remove the tank from the chassis to prevent other components from improper refilling of liquid coolant. Before turning on the power, please confirm that all the tube clips are fastened; leakageofliquidcoolantduetoimproperinstallationmaydamagethesystem,which is not covered by warranty.

Open the lid of the tank to pour in liquid coolant and close the lid.Step 6

Turn on the power until all the liquid coolant drains into the tubes; the red light on the bottom of PCB will blink and bleep; the system will turn off automatically within 4 seconds. (This is normal at this point since the tube and radiatorarenotfullofliquid.)

Step 7

Open the lid of the tank again to refill the tank with liquid coolant and then close the lid. Turn on the power one more time and repeat this step until the liquid coolant is no longer lower than the low water- level.

Warning : Be aware of abnormal leakage. If the installation was correct and the tube chipsarefastened,andtheliquidcoolingsystemleaks,pleaseturnoffthepower immediately and drain out all the coolant. Contact GIGABYTETMdeal-ers or GIGABYTETMservicecenter.

With GIGABYTETM 3D Aurora, Triton and Poseidon series, the water tank can be se-cured inside the chassis with 2 screws ; velcro could be used to place the tank while using chassis other than 3D Aurora, Triton and Pose-idon series.

a :6-pinconnectorb :female2-pinconnector

Step 8

GIGABYTETM 1/2” tube comes with tube clips to prevent leakage.

Liquid Coolant Installation

a

b

c

d

a

b

c :male2-pinconnectord :4-pinconnector

(Figurea) (Figureb )

The following are not covered by the warranty: 1. Usetheproductincorrectlyorinamannerotherthanthedesignedpurpose. 2. Nonobservance of the proper operation provided. (e.g. over-clocking) 3. Malfunctionduetointerferencefromotherdevices. 4. Unauthorized modification of the product. 5. Consequential damage to other objects due to the product’s fault. 6. Malfunction arising from casualties (earthquake, thunder, fire, and flood). 7. The product’s warranty label has been removed or damaged. 8. Thedevicesinside,includingpowersupply,harddisk,CD-ROMdrive,mother-

board, ventilator, etc, are not detached from the chassis prior to the transportation ofthecomputerproduct,resultingindamagetothechassisorcomputer-relateddevices.

9. Any loss caused by failure to follow the installation process contained in the user manual.

10. Anydamagetothesystemarisingfromcoolantleakageduetoimproperinstalla-tion.

11. Use only GIGABYTE™LiquidCoolant.Anydamagearisingfromtheuseofliquidsother than GIGABYTE™ Liquid Coolant is not covered by the warranty.

Installation Guide