installation guide...2.2.3 bolt the wire mesh partition w/ fastening clip on each bolt on the floor....
TRANSCRIPT
INSTALLATION GUIDE
C13-W WIRE MESH PARTITIONChevrolet City Express / Nissan NV200 ( Wire Mesh, Steel )
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 2
QUICK START GUIDE
q 1.1 Setup...................................................................................................................................................q 1.1.1 Unpack components; compare with the bill of materials..............................................................q 1.1.2 Verify all parts are present.............................................................................................................q 1.1.3 Identify the assembly and installation fastener bags.....................................................................
3334
Phase 1 - Assembly
q 2.1 Vehicle preparation..............................................................................................................................q 2.1.1 Floor preparation............................................................................................................................q 2.1.2 Driver and passenger sides preparation.........................................................................................q 2.2 Wire mesh partition installation............................................................................................................q 2.2.1 Attach the driver and passenger side brackets to the threaded hole in the van...........................q 2.2.2 Attach the wire mesh partition with anchor plate to the driver and passenger side wings...........q 2.2.3 Bolt the wire mesh partition w/ fastening clip on each bolt on the floor........................................
5567789
Phase 2 - Installation
REQUIRED ITEMS
2 PERSONS
q Cordless Impactq Cordless Drillq Cutterq Flat Screwdriverq Markerq 1/2" Socketq 1" Hole Sawq 10mm Socketq 13mm Socket
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 3
PHASE 1 – ASSEMBLY1.1 SETUP
1.1.2 Verify all parts are present.
Item No. Description Qty.
30-105 Wire Mesh Panel 1
30-309 Fastening Clip 16
30-358 Driver Side Wing 1
30-359 Passenger Side Wing 1
79-907 Warning Label 1
94-3031 Assembly Fastener Bag 1
96-3015 Installation Fastener Bag 1
1.1.1 Unpack components; compare with the bill of materials.
30-105
30-309
30-35930-358
79-907
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 4
1.1.3 Identify the Assembly and Installation fastener bags.
Assembly Fastener Bag Hardware Assembly
Hardware AssemblyInstallation Fastener Bag
# 98-112Flat Washer1/4", 3/4" ODZINC
2×
# 98-122Lock WasherRegular 5/16"ZINC
4×
# 98-118Lock WasherRegular 1/4"ZINC
2×
4× # 98-116Flat Washer5/16", 7/8" ODZINC
# 90-6684×Hex BoltM8-1.25 × 40 CL 8.8 DIN933 BLACK OXIDE
# 90-8402×Hex BoltM6-1.00 × 50 CL 12.9 DIN933 BLACK OXIDE
Spacer0.375" ID, × 1.0" OD × 0.25" LONGNYLON
# 98-1574×
24×Flat Washer5/16", 7/8" ODZINC
# 98-116
Hex Bolt5/16"-18 × 1"GR-5 ZINC
# 90-20812×
Locknut5/16"-18ZINC
# 94-11012×
12×
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
2×
#90-840 Hex Bolt M6 × 50
#98-118 Lock Washer
#98-112 Flat Washer
4×
#90-668 Hex Bolt M8 × 40
#98-122 Lock Washer
#98-116 Flat Washer
#98-157 Spacers
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 5
2.1.1 Floor preparation.
PHASE 2 – INSTALLATION2.1 VEHICLE PREPARATION
TOOLSq Cordless Impactq 13mm Socket
Remove the 2 D-rings on the floor.
Pull the floor mat up, then put 2 marks on the floor mat on top of the 2 hex bolts.
TOOLSq Marker
Drill or cut the 2 marks, then remove the 2 hex bolts on the floor.
TOOLSq Cordless Impact
q Cordless Drill
q 1" Hole Saw
q 13mm Socket
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 6
2.1.2 Driver and passenger sides preparation.
Remove
Remove
Remove the small plastic covers on the passenger and driver side panel.
TOOLSq Flat screwdriver
Remove the rear bolt under the plastic covers
TOOLSq Cordless Impactq 10mm Socket
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 7
2.2.1 Attach the driver and passenger side brackets to the threaded holes in the van.
TOOLSq Cordless Impactq 10mm Socket
HARDWARE USED
2×
#90-840 Hex Bolt M6 × 50
#98-118 Lock Washer
#98-112 Flat Washer
PHASE 2 – INSTALLATION2.2 WIRE MESH PARTITION INSTALLATION
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 8
2.2.2 Attach the wire mesh partition with anchor plate to the driver and passenger side wings.
TOOLSq Cordless Impactq 1/2" Socketq 1/2” Wrench
HARDWARE USED
12×
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 9
2.2.3 Bolt the wire mesh partition w/ fastening clip on each bolt on the floor.
HARDWARE USED
4×TOOLSq Cordless Impactq 13mm Socket
#90-668 Hex Bolt M8 × 40
#98-122 Lock Washer
#98-116 Flat Washer
#98-157 Spacers
NOTE: Please read and keep the warning partition after the installation.
For technical support, contact us at 1-800-565-5321 C13-W Installation Guide | REV. C1 | Page 10
“Congratulations, you have successfully installed your Wire Mesh Partition!
Thank you for doing business with us.”