installation cd changer attachment 2 door · pdf filecd changer attachment aii 30854 parts...

© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30854 (0509) 1 of 11

PRELIMINARY

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

SEP 2005

08B26-SVA-1000-91

CIVIC2 DOOR

CD CHANGER ATTACHMENTAII 30854

PARTS LIST

CD Changer Attachment (Sold Separately):P/N 08B26-SVA-100

CD Changer Kit (sold separately):P/N 08A26-5E1-100

If you equip with XM radio system

Bus Cable 2 Port (sold separately):P/N 08A31-0F1-000

CD changer bracket

2 Side brackets

3 Clip nuts

3 EPT seals

3 Washer-bolts

4 Flange nuts

15 Wire ties

2 Wire ties with clip

9 Cushion tapes

BUS cable

4 Washer screws

CD changer

Bracket

8-Disc CD magazine

8 Washer-screws, 4 x 6 mm

User’s information

BUS cable 2 Port

dcs

HandA-Accessories.com

2 of 11 AII 30854 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.

PRELIMINARY

TOOLS REQUIREDPhillips screwdriverFlat-tip screwdriverStubby Phillips screwdriver8 mm, 10 mm and 14 mm Combination wrenchesClip remover8 mm ,10 mm and 14 mm SocketsRatchetSmall flat-tip screwdriverContact cleanerShop towelMasking tape

Illustration of the CD Changer Installed on theVehicle

3. Remove the passenger’s dashboard lower cover(four clips, and two pins).

4. Remove the driver’s dashboard lower cover (eightclips).

5422010H

AUDIOUNIT

BUS CABLE

CD CHANGER

5306360T

PASSENGER'SDASHBOARD

CLIPS(4)

PINS(2)

5202121T

CLIPS(8)

DRIVER'SDASHBOARDLOWER COVER

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These procedures shouldnot be attempted by “do-it-yourselfers”.

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.


PRELIMINARY

5. Remove the inside cover from the front consolepocket (two tabs).

6. Lower the steering wheel lever and pull thesteering toward you.

7. To protect the dashboard area, place a shop towelover the steering wheel and shift lever.

8. Apply masking tape to the instrument panel asshown, and remove the instrument panel (one self-tapping screws, 11 clips, and one connector).

9. Apply masking tape to the instrument panel asshown, and remove the center panel (two bolts,ten retaining clips, and unplug the vehicleconnectors).

5624100B

SELF-TAPPINGSCREW

CLIPS (11)

METER PANELMASKING TAPE

5202562T

CLIPS (5)

BOLT

CLIPS (6)

MASKING TAPE

CENTER PANEL

VEHICLECONNECTORS

5202130T

FRONT CONSOLEPOCKET

INSIDECOVERTABS (2)

SIFT LEVER"S" POSITION

5608031H

SHOPTOWEL

STEERINGWHEEL

SHOP TOWEL

COMBINATIONSWITCH

SIFT LEVER

TILT LEVER


PRELIMINARY

10. Remove the two seat track end covers from therear side of the passenger’s seat, then remove thetwo bolts that secure the passenger’s seat.

11. Remove the center console cover:

M/T Vehicle

• Pull down on the shift boot. Remove the shiftknob by turning it counterclockwise.

• Remove the center console cover by removingthe five clips fastening the center consolecover.

5413120H

PASSENGER'SSEAT

SEAT TRACK END COVER

BOLT

5321061H

SHIFT KNOB

SHIFT BOOT

5321072H

CLIPS(3) CENTER

CONSOLECOVER

PARKING BRAKELEVERPull up completely.

CLIPS (2)


PRELIMINARY

14. Inside the passenger’s compartment area, removethe rear seat cushion by removing the bolt andreleasing the two hooks.

A/T Vehicle

• Remove the center console cover (five clips).

12. Open the center console lid, and remove the mat.

13. Remove the center console (four bolts, two clips,and the vehicle connector).

15. Open the trunk lid, fold the rear seatback forwardby pulling the levers under the rear parcel shelf.Remove the trunk floor mat (two clips).

5202173T

CLIPS(3) CENTER

CONSOLECOVER

PARKING BRAKELEVERPull up completely.

SHIFT LEVER("N" position)

CLIPS (2)

5202184T

BOLTS(4)

MAT

CLIP

CENTERCONSOLELID

VEHICLECONNECTOR

CENTERCONSOLE

CLIP

5422020H

BOLT

HOOK REAR SEAT CUSHION

5422031H

TRUNKFLOORMAT

CLIPS (2)

LEVER

REARSEATBACK

LEVER


PRELIMINARY

16. Remove the trunk weatherstrip from the edge ofthe trunk opening in the area shown.

17. Remove the rear trim panel (two clips and threehooks).

18. Continue removing the weatherstrip in the areashown. Remove the five clips, then pull out on theright trunk side trim panel in the direction shown.

Routing the BUS cable

19. Route the BUS cable from the trunk along thevehicle harness.

20. Lift up and lock the right rear seatback, thenremove the clip that secures the floor carpet. Pullback the floor carpet

5422042H

TRUNKWEATHERSTRIP

CLIPS(2)

REAR TRIMPANEL

HOOKS(3)

5425011HRIGHT TRUNK SIDETRIM PANEL

CLIP

CLIP (3)Turn the center pin ina counterclockwisedirection to remove.

5413032H

FLOOR

CARPETBUS

CABLERouteunder thefloor carpet.

CLIP

5413022H

BUS CABLE

REARSEATBACK

SEAT BRACKET

BUS CABLE


PRELIMINARY

24. Along the center console area, secure the BUScable to the vehicle harness with three wire ties.

21. Route the BUS cable forward to the right frontconsole frame along the vehicle harness.

22. Continue routing the BUS cable to the dashboardand out through the dash opening.

23. Measure 300 mm from the end of the BUS cable,then secure the BUS cable to the vehicle harnesswith four wire ties in the areas shown.

25. Using isopropyl alcohol on a shop towel, clean theareas where the cushion tape will attach. Attachthe BUS cable to the floor panel with the threecushion tapes in the area shown.

5609010H

DASHOPENING

DASHOPENING

BUSCABLE

BUSCABLE

VEHICLEHARNESS

5222034H

BUS CABLECONNECTOR

300 mm

BUS CABLE

WIRE TIE

5609031H

VEHICLEHARNESS

BUSCABLE

CUSHIONTAPE

WIRE TIE

CUSHIONTAPE


PRELIMINARY

26. Pull back the floor carpet, then attach the BUScable to the floor panel with the two cushion tapesin the areas shown.

27. Secure the BUS cable to the vehicle harness withthe three wire ties in the areas shown.

28. Secure the BUS cable to the vehicle harness withthe two wire ties in the areas shown.

29. Attach the BUS cable to the floor panel with thethree cushion tapes in the areas shown.

Installing the CD Changer

30. Using a flat-tip screw driver, set the adjustmentknobs in the “H: HORIZONTAL” position.

31. Position the CD changer brackets on the sides ofthe CD changer, then install the four 4 x 8 mmwasher-screws.

5413042H

WIRE TIE

BUSCABLE

Turn over.

BUSCABLE

CUSHION TAPE

VEHICLEHARNESS

5413053H

BUSCABLE

REARSEATBACK

WIRETIE

CUSHIONTAPE

WIRETIE

CUSHIONTAPE

VEHICLEHARNESS

CUSHIONTAPE

4413031Y

(FACTORY SETPOSITION)

(POSITIONAFTER SETTING)

CDCHANGER

ADJUSTINGKNOB

V: VERTICAL

H: HORIZONTAL

5216010H

4 x 8 mmWASHER-SCREWS (2)

SIDE BRACKET

CDCHANGER

4 x 8 mmWASHER-SCREWS (2)


PRELIMINARY

32. Position the CD changer on the CD changerbracket, then install and tighten the four 6 mmflange nuts.

33. Wrap one EPT sealer around the BUS cableconnector from the CD changer, then secure theBUS cable and connector to the CD changerbracket with two wire ties.

34. In the trunk, slide the clip nut into position on therear seat panel through the hole in the panel. Ifnecessary, spread the clip nut open with a smallflat-tip screwdriver.

35. Loosely install the washer-bolt to the rear seatpanel first. Then, place the end of the CD changerbracket between the seat panel and clip nut youjust installed.

5413070H

CD CHANGERBRACKET

CDCHANGER

WIRE TIE

EPT SEALERCD CHANGERBUS CABLECONNECTOR

5413060H

CDCHANGER

CD CHANGERBRACKET

FLANGE NUTS(4)

5413082H

CLIP NUT

WASHER-BOLT

CDCHANGER

CD CHANGER BRACKET(Place the end of thebracket between theseat panel and clip nutyou just installed.)


PRELIMINARY

36. Slide the two clip nuts onto the CD changerbracket and parcel shelf through the holes in theparcel shelf, and align their holes as shown. Installthe two washer-bolts and tighten them securely.

37. Connect the BUS cable connector to theconnector on the CD changer.

38. Fold the excess BUS cable, and secure the BUScable to the holes in the rear seat panel with thetwo wire ties with clips.

If the vehicle you’re working on is equipped withXM radio, continue with step 39; otherwise, go tostep 41.

39. Plug the BUS cable 2 port connectors to the twoBUS cables.

40. Wrap the two connectors with two EPT sealers.

5413091H

WASHER-BOLT

CDCHANGERBRACKET

CLIP NUT

CLIP NUT

CDCHANGERBRACKET

PARCEL SHELF

5413110H

CDCHANGER

RIGHT SEAT PANEL

BUS CABLE

WIRE TIESWITH CLIPS (2)

Fold theexcesscable.

5420060H

BUS CABLE 2 PORT

BUS CABLES(2)

EPT SEALER

EPT SEALER

5413103H

BUS CABLE

BUS CABLECONNECTOR

CUSHIONTAPE

CDCHANGER

CD CHANGERCONNECTOR


PRELIMINARY

< Multi Control CD Tuner Unit >

41. Plug the BUS cable connector into the rear of thehead unit.

< Standard Audio Unit >

< Navigation Head Unit >

5801030H

HEAD UNIT

BUS CABLE orBUS CABLE 2 PORT

5801010H

AUDIO UNIT

5826220H

CD TUNER

PLAYER

5801020HPOCKET

CD TUNER

< CD Tuner with Cassette Player >

5826210H

CD TUNER

PLAYER

< CD Tuner with Media Player >

BUS CABLE

BUS CABLE

BUS CABLE orBUS CABLE 2 PORT

BUS CABLE


PRELIMINARY

42. Connect the vehicle connectors to the centerpanel, and reinstall the center panel.

43. Check that all wire harnesses are routed properlyand all connectors are plugged in.

44. Reconnect the negative cable to the battery.

45. Reset the clock and the radio station presets.

46. Check the operation of the CD changer asdescribed in the User’s information supplied.

47. Reinstall all removed parts.

48. Put the CD changer User’s information in the glovebox for your customer.

NOTE: When the battery is disconnected, the driver’swindow AUTO function is disabled.

• Start the engine. Push down on the driver’s windowswitch until the window is fully open.

• Pull up on the driver’s window switch to close thewindow completely, then hold the switch for2 seconds or more.

• Lower and raise the driver’s window to checkoperation of the driver’s window AUTO function.

5405080H

CENTER PANEL

BOLT(Reused)

VEHICLECONNECTORS

installation cd changer attachment 2 door · pdf filecd changer attachment aii 30854 parts...

Documents