inst hbb 04/18 · the bottom surface of the poly-styrene block must be exactly aligned with the...
TRANSCRIPT
HALFEN HBB INST_HBB 04/18
Assembly Instructions • Montageanleitung • Instrukcja montażu
bi-Trapez box
D bi-Trapez-Box
bi-Trapez-Box
GB
PL
Deu
tsch
Engl
ish
Pols
ki
2 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Assembly Instructions
2 1
Available bi-Trapez boxes
Article name Exterior dimension HBB Box
h × b × t [mm]
For slabthickness d [mm]
HBB 16 - O / -OQ / -OQS 187 × 274 × 155 ≥ 160
HBB 18 - O / -OQ / -OQS 207 × 274 × 155 ≥ 180
HBB 20 - O / -OQ / -OQS 227 × 274 × 155 ≥ 200
Article name * For slab thickness d [mm]
HBB Reinforcement cage 16-Q-Unit ≥ 160
HBB Reinforcement cage 18-Q-Unit ≥ 180
HBB Reinforcement cage 20-Q-Unit ≥ 200
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
HBB-O with one bi-Trapez bearing ® at the bottom of the box
HBB-O Scope of delivery:
HBB-OQ with an additional bi-Trapez bearing ® in the top of the box for vertical upward loads
HBB-OQS includes a bearing at the bottom of the box and in the top for additional vertical loads and two bi-Trapez bearings® fi xed to the inner sides for additional horizontal loads
bi-Trapez box HBB-O, -OQ or -OQS (see left)
bi-Trapez bearing ®: one, two or four pieces, depends on box (see left)
Protective (cardboard) strip
Polystyrene fi ller
Fixing nails to facilitate fi tting to formwork*
Polystyrene installation block
Formwork*(*formwork is not scope of delivery)
All versions are delivered with the bi-Trapez bearings® securely fi xed in the bi-Trapez box.
A – HALFEN HBB bi-Trapez box for on-site cast landing slabs
HALFEN HBB Reinforcement cage-Q-Unit
3 4
6
7
5
Formwork
Ø 8Ø 8Ø 12
Ø 10
365
120
/ 14
0 / 16
0 *
700
Deu
tsch
Engl
ish
Pols
ki
3© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Assembly Instructions
The HALFEN bi-Trapez box is positi-oned on the masonry with the poly-styrene fi ller and block inserted.The brickwork around the box is then completed. The cardboard protection strip is left in the bottom of the box to protect the bearing.
The polystyrene fi ller and block keep the box in shape until the surrounding brickwork is fi nished, and are removed after the mortar has suffi ciently hardened.
OBEN
OBEN
HAUT
TOP
18
bi-Trapez-Box
mm
Mortar bed min. MG IIa
min. 15 mm
A1 – Installation in brickwork
The polystyrene block is attached to the formwork using the fi xing nails . The bottom surface of the poly-styrene block must be exactly aligned with the bottom surface of the slab.
Place the protective strip and the polystyrene fi ller in the bi-Trapez box.
Slide the HALFEN HBB bi-Trapez box on to the polystyreneblock.
The bi-Trapez box is cast in the concrete slab or wall.
2.1
1.1
2.2
2.3 2.4
5 6
7
A2 – Installation in reinforced concrete walls or slabs
4 3
→
Deu
tsch
Engl
ish
Pols
ki
4 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Assembly Instructions
Install the formwork for the landing slab. Remove the poly-styrene block and the polysty-rene filler from the HALFEN HBB bi-Trapez box. Leave the protective cardboard strip in the bi-Trapez box.
The protective cardboard strip must be positioned correctly in the bi-Trapez box. Insert the HBB Reinforcement cage, including the spacers, completely into the box.(Spacers are not illustrated and not included in delivery)
Install the insulation strips between the landing slab and the adjoining walls. Make sure there are no gaps between the strips.
Install HTPL Insulation strips in all joint between walls and planned stairs.
Ensure correct orientation of the reinforcement!
A3 – Installation in stair landing slab (on-site cast)
6
4
3
8
8
3.1
3.1
3.2 3.2
3.3 3.3
3.4 3.4
Continous perimeter jointinsulation HTPL
Deu
tsch
Engl
ish
Pols
ki
5© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Assembly Instructions
3.8
3.6 3.6
Install the on-site reinforcement according to the reinforcement plan. Tie and secure the HBB Reinforcement cage. Pour the concrete for the stairs landing slab.
Vertical section:Concrete cover cnom in [mm]
* FFL= fi nished fl oor level SFL= structural fl oor level
Horizontal section:Concrete cover cnom in [mm]
15
15 60
60
80
80
2020
2020
Ensure concrete cover is as illustrated!
Ensure concrete cover is as illustrated!
Care must be taken with all connection joints to avoid sound bridges caused by concrete residue or other contamination bridging the insulation!
A3 – Installation in stair landing slab (on-site cast) – continued
3.7
3.5
3.7
3.5
3.8
2 stirrups Ø8, install on-site
2 stirrups Ø8, install on-site
Formwork
Plan viewformwork
HTPL Insulation strip
bi-Trapez box
SFL*
FFL*
3.63.6
Deu
tsch
Engl
ish
Pols
ki
6 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Assembly Instructions
Available bi-Trapez-Boxes
Article name Inner dimension HBB Box
h × b × t [mm]
For slabthickness d [mm]
HBB 16 - F / -FQ / -FQS 160 × 250 × 140 ≥ 160
HBB 18 - F / -FQ / -FQS 180 × 250 × 140 ≥ 180
HBB 20 - F / -FQ / -FQS 200 × 250 × 140 ≥ 200
Available HBB-Sets
Article name For slabthickness d [mm]
HBB 16-SET ≥ 160
HBB 18-SET ≥ 180
HBB 20-SET ≥ 200
HBB 16-SET-Q ≥ 160
HBB 18-SET-Q ≥ 180
HBB 20-SET-Q ≥ 200
HBB 16-SET-QS ≥ 160
HBB 18-SET-QS ≥ 180
HBB 20-SET-QS ≥ 200
Article name * For slab thickness d [mm]
HBB Reinforcement cage 16-Q-Unit ≥ 160
HBB Reinforcement cage 18-Q-Unit ≥ 180
HBB Reinforcement cage 20-Q-Unit ≥ 200
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
HBB-SET Scope of delivery:
bi-Trapez box HBB-F, -FQ or -FQS (see left)
bi-Trapez bearing ®: one, two or four pieces, depends on box (see left)
HBB Reinforcement cage-Q-Unit
All types are delivered with the bi-Trapez bearings® securely fi xed in the bi-Trapez-Box.
B – HALFEN HBB bi-Trapez-Box for precast landing slabs
HALFEN HBB-Reinforcement cage-Q-Unit
2
3
1
Ø 8Ø 8Ø 12
Ø 10
365
120
/ 14
0 / 16
0 *
700
HBB-F including one bi-Trapez bearing ® in the bottom of the box
HBB-FQ with an additional bi-Trapez bearing ® in the top of the box for vertical upward loads
HBB-FQS includes a bearings in the bottom of the box and at the top for additional vertical loads and two bi-Trapez bearings® fi xed to the inner sides for additional horizontal loads
Deu
tsch
Engl
ish
Pols
ki
7© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Assembly Instructions
B1 – In the precast plant
B2 – On-site installation
1.1
2.1
1.2
The stair landing slab is cast with consoles with the inner dimensions of the HBB Box (h × b × t, see table)The reinforcement cages are installed, with spacers, at this stage (spacers are not illustrated and not included in delivery).
Slide the HALFEN HBB bi-Trapez boxes on to the consoles.
The reinforcement for the stair landing slab is installed accor-ding to the reinforcement plan.Tie and secure the HBB-Reinforcement cage. Pour the concrete for the stair landing slab.
Ensure concrete cover is as illustrated!
15
2020
15 60 80
2020
1.1
1.2
OBEN
HAUT
TOP
18
bi-Trapez-Box
2.1
Console
Landing slab
Figures 2.1 - 2.5 are design examples. The information provided by the structural engineer is always decisive.
i
2 stirrups Ø8, install on-site
2 stirrups Ø8, install on-site
H–H
Vertical section
Concrete cover cnom in the console in [mm]
Horizontal section H–H
Plan viewformwork
SFL*
* SFL= Structural fl oor level
Deu
tsch
Engl
ish
Pols
ki
8 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Assembly Instructions
B2 – On-site installation (continued)
Care must be taken at all connections to avoid sound bridges caused by concrete residue or other contamination bridging the insulation!
2.5 2.5
2.4
≥ 1.
5 cm
Mortar bed
Avoid acoustic bridging!
HALFEN HBB bi-Trapez box
HALFEN HTPL Insulation strip
2.3
2.3
Install HTPL Sound absorbing strips in all joints between the slab and walls and cover the gaps between the HTPL Strips with HALFEN Adhesive tape.
Place the prefabricated element with the HALFEN bi-Trapez boxes at the intended position on the pre-prepared mortar beds. (min. MG IIa according to DIN EN 1996, thickness ≥ 1.5 cm).
2.3
Continous perimeter jointinsulation HTPL
Deu
tsch
Engl
ish
Pols
ki
9© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Montageanleitung
Lieferbare bi-Trapez-Boxen
Artikel bezeichnung Außenmaße derHBB Box
h × b × t [mm]
Für Podest-stärke
d [mm]
HBB 16 - O / -OQ / -OQS 187 × 274 × 155 ≥ 160
HBB 18 - O / -OQ / -OQS 207 × 274 × 155 ≥ 180
HBB 20 - O / -OQ / -OQS 227 × 274 × 155 ≥ 200
Artikel bezeichnung * für Podestdicken d [mm]
HBB-Bewehrungskorb 16-Q-Unit ≥ 160
HBB-Bewehrungskorb 18-Q-Unit ≥ 180
HBB-Bewehrungskorb 20-Q-Unit ≥ 200
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
HBB-O inkl. eines bi-Trapezlagers ® im Boden
Lieferumfang HBB-O:
HBB-OQ bei zusätzl. abhebenden Lasten inkl. je eines bi-Trapez-lagers ® im Boden und im Boxen-deckel
HBB-OQS bei zusätzl. abhebenden und seit-lichen Lasten inkl. je eines bi-Tra-pezlagers ® im Boden und im Bo-xendeckel sowie zweier Elemente in den Seitenwänden.
bi-Trapez-Box HBB-O, -OQ oder -OQS (s. links)
bi-Trapezlager ®: ein, zwei oder vier Stück, je nach Box (s. links)
Schutzstreifen (Pappe)
Polystyrol-Einlage
Spezialnägel zur einfachen Befestigung an der Schalung*
Polystyrol-Montageblock
Schalung(*Schalung nicht Teil des Lieferumfangs)
Die bi-Trapezlager ® sind bei allen Bestellvarianten werkseitig in die bi-Trapez-Box eingeklebt.
A – HALFEN HBB bi-Trapez-Box für Ortbetonpodeste
HALFEN HBB-Bewehrungskorb-Q-Unit
2
3 4
6
7
5
1
Schalung
Ø 8Ø 8Ø 12
Ø 10
365
120
/ 14
0 / 16
0 *
700
Deu
tsch
Engl
ish
Pols
ki
10 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Montageanleitung
Die HALFEN bi-Trapez-Box wird mit den eingelegten Polystyrolblöcken und in der Wand positioniert und ummauert. Der eingelegte Schutzstreifen schützt hierbei die Profi lierung im Boxenboden vor Verschmutzung.
Die Polystyrolkörper garantieren beim Ummauern die Formhaltigkeit der Box und werden nach Aushärten des Mör-tels entfernt.
OBEN
OBEN
HAUT
TOP
18
bi-Trapez-Box
mm
Mörtelbett mind. MG IIa
min. 15 mm
A1 – Einbau in Mauerwerk
Den Polystyrol Montageblock an der vorgesehenen Stelle mit den Spezialnägeln an der Schalung befestigen. Die Unterkante des Polystyrolblocks muss genau in Höhe der Unterkante des Betonpodestes liegen.
Der Schutzstreifen und die Polystyroleinlage werden in die bi-Trapez-Box eingelegt.
Die HALFEN HBB bi-Trapez-Box wird auf den Polystyrol-block aufgeschoben.
Die bi-Trapez-Box wird mit in die zu erstellende Beton-decke oder -wand einbetoniert.
2.1
1.1
2.2
2.3 2.4
5 6
7
A2 – Einbau in Stahlbetondecke oder -wand
4 3
→
Deu
tsch
Engl
ish
Pols
ki
11© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Montageanleitung
Podestschalung errichten. Polystyrolblock und Poly-styrol-Einlage aus der einbeto-nierten HALFEN HBB bi-Trapez-Box entfernen. Der Schutzstreifen bleibt in der bi-Trapez-Box.
Der Schutzstreifen muss ordnungsgemäß in der bi-Trapez Box eingelegt sein. Nun den HBB-Bewehrungskorb-Q-Unit inkl. Abstandhaltern (nicht dargestellt, nicht im Liefer-umfang enthalten) vollständig in die Box einschieben.
In die Fugen zwischen Podest und tragender Wand lückenlos HTPL Fugenplatten einbauen.
HTPL Fugenplatten umlaufend auch in der Fuge zwischen Wand und geplanter Treppe ein-bauen.
Korrekte Ausrichtung des Korbes beachten!
A3 – Einbau in Treppenpodest (Ortbeton)
6
4
3
8
8
3.1
3.1
3.2 3.2
3.3 3.3
3.4 3.4
Durchgehend umlaufende Fugen-platten HTPL
Deu
tsch
Engl
ish
Pols
ki
12 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Montageanleitung
3.8
3.6 3.6
Bauseitige Bewehrung entspre-chend Bewehrungsplan verlegen.HBB-Bewehrungskorb feströdeln.Anschließend Treppenpodest betonieren.
Vertikalschnitt:Betondeckung cnom in [mm]
Horizontalschnitt:Betondeckung cnom in [mm]
15
15 60
60
80
80
2020
2020
Betondeckung wie dargestellt gewährleisten!
Betondeckung wie dargestellt gewährleisten!
Bei allen Anschlüssen ist darauf zu achten, dass Schallbrücken durch Verun-reinigungen oder eindrin-genden Beton vermieden werden!
A3 – Einbau in Treppenpodest (Ortbeton) – Fortsetzung
3.7
3.5
3.7
3.5
3.8
2 Bügel Ø8, bauseitig einbauen
2 Bügel Ø8, bauseitig einbauen
Schalung
DraufsichtSchalung
HTPL Fugenplatte
bi-Trapez-Box
OKRD
OKFF
3.63.6
Deu
tsch
Engl
ish
Pols
ki
13© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Montageanleitung
Lieferbare bi-Trapez-Boxen
Artikel bezeichnung Innenmaße derHBB Box
h × b × t [mm]
Für Podest-stärke
d [mm]
HBB 16 - F / -FQ / -FQS 160 × 250 × 140 ≥ 160
HBB 18 - F / -FQ / -FQS 180 × 250 × 140 ≥ 180
HBB 20 - F / -FQ / -FQS 200 × 250 × 140 ≥ 200
Lieferbare HBB-Sets
Artikel bezeichnung Für Podest-dicke
d [mm]
HBB 16-SET ≥ 160
HBB 18-SET ≥ 180
HBB 20-SET ≥ 200
HBB 16-SET-Q ≥ 160
HBB 18-SET-Q ≥ 180
HBB 20-SET-Q ≥ 200
HBB 16-SET-QS ≥ 160
HBB 18-SET-QS ≥ 180
HBB 20-SET-QS ≥ 200
Artikel bezeichnung * für Podestdicken d [mm]
HBB-Bewehrungskorb 16-Q-Unit ≥ 160
HBB-Bewehrungskorb 18-Q-Unit ≥ 180
HBB-Bewehrungskorb 20-Q-Unit ≥ 200
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
HBB-F inkl. eines bi-Trapezlagers ® im Boden
Lieferumfang HBB-SET:
HBB-FQ bei zusätzl. abhebenden Lasten inkl. je eines bi-Trapez-lagers ® im Boden und im Boxen-deckel
HBB-FQS bei zusätzl. abhebenden und seit-lichen Lasten inkl. je eines bi-Tra-pezlagers ® im Boden und im Bo-xendeckel sowie zweier Elemente in den Seitenwänden.
bi-Trapez-Box HBB-F, -FQ oder -FQS (s. links)
bi-Trapezlager ®: ein, zwei oder vier Stück, je nach Box (s. links)
HBB-Bewehrungskorb-Q-Unit
Die bi-Trapezlager ® sind bei allen Bestellvarianten werkseitig in die bi-Trapez-Box eingeklebt.
B – HALFEN HBB bi-Trapez-Box für Fertigteilpodeste
HALFEN HBB-Bewehrungskorb-Q-Unit
2
3
1
Ø 8Ø 8Ø 12
Ø 10
365
120
/ 14
0 / 16
0 *
700
Deu
tsch
Engl
ish
Pols
ki
14 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Montageanleitung
B1 – Im Fertigteilwerk
B2 – Auf der Baustelle
1.1
2.1
1.2
Das Treppenpodest wird mit Konsolen mit den Innenmaßen der HBB Box (h × b × t, siehe Tabelle) hergestellt. Der HBB Bewehrungskorb-Q-Unit wird dabei inkl. Abstands-haltern (nicht dargestellt, nicht im Lieferumfang enthalten) ein-gebaut.
HALFEN HBB bi-Trapez-Boxenauf die Konsolen schieben.
Anschließend ist die Bewehrung des Treppenpodestes gem. Bewehrungs-plan zu verlegen.HBB-Bewehrungskorb feströdeln.Treppenpodest betonieren.
Betondeckung wie dargestellt gewährleisten!
15
2020
15 60 80
2020
1.1
1.2
OBEN
HAUT
TOP
18
bi-Trapez-Box
2.1
Konsole
Podest
Die Abbildungen 2.1 - 2.5 sind Ausführungsbeispiele; in jedem Fall sind die Anga-ben des Tragwerksplaners maßgebend.
i
2 Bügel Ø8, bauseitig einbauen
2 Bügel Ø8, bauseitig einbauen
H–H
Vertikalschnitt
Betondeckung cnom in der Konsole in [mm]
Horizontalschnitt H–H
DraufsichtSchalung
OKRD
Deu
tsch
Engl
ish
Pols
ki
15© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
HALFEN HBB Montageanleitung
B2 – Auf der Baustelle (Fortsetzung)
Bei allen Anschlüssen ist darauf zu achten, dass Schallbrücken durch Verun-reinigungen oder eindrin-genden Beton vermieden werden!
2.5 2.5
2.4
≥ 1,
5 cm
Mörtelbett
Schallbrücke vermeiden!
HALFEN HBB bi-Trapez-Box
HALFEN HTPL Fugenplatte
2.3
2.3
Schalldämmplatten HTPL umlau-fend in alle Fugen zwischen Po-dest und Wand einbauen und Stöße zwischen den HTPL Plat-ten mit Klebeband abkleben.
Das mit den HALFEN bi-Trapez-Boxen bestückte Fertigteil an der vorgesehenen Position auf die vorbereiteten Mörtelbetten (mind. MG IIa nach DIN EN 1996, Dicke ≥ 1,5 cm) aufl agern.
2.3
Durchgehend umlaufende Fugen-platten HTPL
Pols
ki
16 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
Deu
tsch
Engl
ish
HALFEN HBB Instrukcja montażu
Rodzaje skrzynek bi-Trapez-Box
Oznaczenie artykułu Wymiary zewnętrzne skrzynki HBB h × b × t [mm]
Grubość podestu d [mm]
HBB 16 - O / -OQ / -OQS 187 × 274 × 155 ≥ 160
HBB 18 - O / -OQ / -OQS 207 × 274 × 155 ≥ 180
HBB 20 - O / -OQ / -OQS 227 × 274 × 155 ≥ 200
Oznaczenie artykułu * Grubość podestu d [mm]
Zbrojenie HBB 16-Q-Unit ≥ 160
Zbrojenie HBB 18-Q-Unit ≥ 180
Zbrojenie HBB 20-Q-Unit ≥ 200
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
HBB-O łącznie z wkładką elastomerową ® na dnie.
Zakres dostawy HBB-O:
HBB-OQ przy dodatkowych obciążeniach podnoszących, łącznie z wkładką elastomerową bi-Trapezlager ® na dnie i pokrywie skrzynki.
HBB-OQS przy dodatkowych obciążeniach podnoszących i bocznych, łącznie z wkładką elastomerową bi-Trapezlager ® na dnie, pokrywie i ściankach bocznych skrzynki.
Skrzynka bi-Trapez-Box HBB-O, -OQ lub-OQS (patrz po lewej)
Wkładka elastomerowa bi-Trapezlager ®: jedna, dwie lub cztery sztuki na skrzynkę (patrz po lewej)
Wkładka ochronna z tektury
Wkładka styropianowa
Specjalne gwoździe do mocowania w szalunku*
Blok styropianowy
Szalunek (*szalunek nie jest częścią dostawy)
Wkładki elastomerowe bi-Trapezlager ® są wklejane do skrzynek, we wszystkich wariantach zamówień.
A – HALFEN HBB bi-Trapez-Box dla podestów betonowanych na budowie
HALFEN zbrojenie HBB-Q-Unit
2
3 4
6
7
5
1
Szalunek
Ø 8Ø 8Ø 12
Ø 10
365
120
/ 14
0 / 16
0 *
700
Pols
ki
17© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
Deu
tsch
Engl
ish
HALFEN HBB Instrukcja montażu
Ustawić skrzynkę HALFEN bi-Trapez-Box wraz z zamontowanym blokiem styropianowym i i obmurować. Wkładka ochronna chroni profi lo-wanie na dnie skrzynki przed zabrud-zeniem.Elementy styropianowe gwarantują przy pracach murarskich zachowanie kształtu skrzynki, po stwardnieniu za-prawy są usuwane.
OBEN
OBEN
HAUT
TOP
18
bi-Trapez-Box
mm
Podłoże z zaprawy min. MGIIa
min. 15 mm
A1 – Montaż w ścianie murowanej
Zamocować blok styropianowy w przewidzianym miejs-cu przy pomocy specjalnych gwoździ do szalunku .Dolna krawędź bloku styropianowego musi leżeć dokładnie na wysokości dolnej krawędzi podestu.
Wkładka ochronna i wkładka styropianowa wkładane są do skrzynki bi-Trapez-Box.
Skrzynka HBB bi-Trapez-Box nasuwana jest na blok styropia-nowy.
Skrzynkę HBB bi-Trapez-Box zabetonować w stropie beto-nowym.
2.1
1.1
2.2
2.3 2.4
5 6
7
A2 – Montaż w ścianie lub stropie żelbetowym
4 3
→
Pols
ki
18 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
Deu
tsch
Engl
ish
HALFEN HBB Instrukcja montażu
Wykonać szalunek podestu. Usunąć blok styropianowy i wkładkę styropianową z zabetonowanej skrzynki HALFEN HBB bi-Trapez-Box. Wkładka ochronna z tektury pozostaje w skrzynce bi-Trapez-Box.
Wkładka ochronna musi być odpowiednio umieszczona w skrzynce bi-Trapez-Box. Wsunąć zbrojenie HBB włącznie z elementami dystansowymi (dystanse nie są przedstawione na rysunku i nie są objęte dostawą).
Zamontować płyty HTPL pomiędzy podestem i ścianą nośną.
Przymocować płyty HTPL do ścian w miejscu planowanych biegów i podestów.
Zwracać uwagę na właściwe położenie zbrojenia!
A3 – Montaż w podeście klatki schodowej (beton monolityczny)
6
4
3
8
8
3.1
3.1
3.2 3.2
3.3 3.3
3.4 3.4
Płyty HTPL umieszczone w sposób ciągły
Pols
ki
19© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
Deu
tsch
Engl
ish
HALFEN HBB Instrukcja montażu
3.8
3.6 3.6
Rozłożyć zbrojenie budowlane według projektu. Przywiązać zbrojenie HBB. Betonować podest.
Przekrój pionowy:Otulina betonowa cnom w [mm]
Przekrój poziomy:Otulina betonowa cnom w [mm]
15
15 60
60
80
80
2020
2020
Zagwarantować otulinę betonową!
Zagwarantować otulinę betonową!
Przy wszystkich połączeniach unikać mostków akustycz-nych przez zanieczyszczenia lub beton!
A3 – Montaż w podeście klatki schodowej (beton monolityczny) – kontynuacja
3.7
3.5
3.7
3.5
3.8
2 strzemiona Ø8, montować na budowie =Poziom posadzki
=Poziom płyty podestu
2 strzemiona Ø8, montować na budowie
Szalunek
Widok z górySzalunek
Płyty HTPL
Skrzynka bi-Trapez-Box
3.63.6
Pols
ki
20 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
Deu
tsch
Engl
ish
HALFEN HBB Instrukcja montażu
Rodzaje skrzynek bi-Trapez-Box
Oznaczenie artykułu Wymiary wewnętrzne skrzynki
h × b × t [mm]
Dla podestu o grubości d [mm]
HBB 16 - F / -FQ / -FQS 160 × 250 × 140 ≥ 160
HBB 18 - F / -FQ / -FQS 180 × 250 × 140 ≥ 180
HBB 20 - F / -FQ / -FQS 200 × 250 × 140 ≥ 200
Dostarczane zestawy HBB
Oznaczenie artykułu Grubość podestu d [mm]
HBB 16-SET ≥ 160
HBB 18-SET ≥ 180
HBB 20-SET ≥ 200
HBB 16-SET-Q ≥ 160
HBB 18-SET-Q ≥ 180
HBB 20-SET-Q ≥ 200
HBB 16-SET-QS ≥ 160
HBB 18-SET-QS ≥ 180
HBB 20-SET-QS ≥ 200
Oznaczenie artykułu * Grubość podestu d [mm]
Zbrojenie HBB 16-Q-Unit ≥ 160
Zbrojenie HBB 18-Q-Unit ≥ 180
Zbrojenie HBB 20-Q-Unit ≥ 200
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
OBEN
HAUT
TOP
18
bi-Trapez-Box
HBB-F włącznie z wkładką elastomerową bi-Trapezlagers ® w dnie skrzynki
Zakres dostawy HBB-SET:
HBB-FQ przy dodatkowych obciążeniach podnoszących, włącznie z wkładką elastomerową bi-Trapez-lagers ® na dnie i pokrywie skrzynki
HBB-FQS przy dodatkowych obciążeniach podnoszących i bocznych, włącznie z wkładką elastomerową bi-Trapezlagers ® w dnie, pokrywie i w ściankach bocznych skrzynki.
bi-Trapez-Box HBB-F,-FQ lub –FQS (patrz po lewej)
bi-Trapezlager ®: jedna, dwie lub cztery sztuki na skrzynkę (patrz po lewej)
HBB zbrojenie Q-Unit
Wkładki elastomerowe bi-Trapezlager ® wklejane są w zakładzie produkcyjnym dla wszystkich wariantów.
B – HALFEN HBB bi-Trapez-Box dla elementów prefabrykowanych
Zbrojenie HBB-Q-Unit
2
3
1
Ø 8Ø 8Ø 12
Ø 10
365
120
/ 14
0 / 16
0 *
700
Pols
ki
21© 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
Deu
tsch
Engl
ish
HALFEN HBB Instrukcja montażu
B1 – W zakładzie prefabrykacji
B2 – Na budowie
1.1
2.1
1.2
Podest wykonuje się ze wsporni-kami o wymiarach wewnętrznych skrzynki HBB (h x b x t, patrz tabela).Zbrojenie HBB–Q-Unit monto-wane jest łącznie z elementami dystansowymi (nie są przedsta-wione i nie są objęte dostawą).
Skrzynki HBB bi-Trapez-Box nasunąć na wsporniki.
Rozłożyć zbrojenie podestu według projektu. Przywiązać zbrojenie HBB. Betonować podest.
Zapewnić otulinę betonową jak przedstawiono!
15
2020
15 60 80
2020
1.1
1.2
OBEN
HAUT
TOP
18
bi-Trapez-Box
2.1
Wspornik
Podest
Rysunki 2.1 – 2.5 są przykładami; zawsze obowiązują dane z projektu technicznego.
i
2 strzemiona Ø8, montować na budowie
2 strzemiona Ø8, montować na budowie
H–H
Przekrój pionowy
Otulina betonowa cnom we wsporniku [mm]
Przekrój poziomy H-H
Widok szalunku
=Poziom płyty podestu
Pols
ki
22 © 2018 HALFEN · INST_HBB 04/18 · www.halfen.com
Deu
tsch
Engl
ish
HALFEN HBB Instrukcja montażu
B2 – Na budowie (kontynuacja)
We wszystkich połączeniach unikać mostków akustycz-nych poprzez zanieczyszcze-nia lub beton!
2.5 2.5
2.4
≥ 1,
5 cm
Podłoże z zaprawy
Unikać mostków akustycznych!
HALFEN HBB bi-Trapez-Box
Płyta HALFEN HTPL
2.3
2.3
Płyty HTPL przymocować do ściany w miejscu biegów i po-destów. Styki na połączeniach płyt okleić taśmą.
Posadowić prefabrykat podestu na przygotowane podłoże z naniesioną zaprawą według EN1996 o grubości ≥ 1,5 cm.
2.3
Płyty HTPL dookoła biegów i podestów
NOTES REGARDING THIS DOCUMENTTechnical and design changes reserved. The information in this publication is based on state-of-the-art technology at the time of publication. We reserve the right to make technical and design changes at any time. HALFEN GmbH shall not accept liability for the accuracy of the information in this publication or for any printing errors.
The HALFEN GmbH subsidiaries in Germany, France, the Netherlands, Austria, Poland, Switzerland and the Czech Republic are Quality Management certifi ed according to ISO 9001:2015, Certifi cate no. 202384-2016-AQ-GER-DAkkS.
Furthermore HALFEN is represented with sales offi ces and distributors worldwide.
Austria HALFEN Gesellschaft m.b.H.Leonard-Bernstein-Str. 101220 Wien
Phone: +43 - 1 - 259 6770 E-Mail: offi [email protected]: www.halfen.at
Fax: +43 - 1 - 259 - 6770 99
Belgium /Luxembourg
HALFEN N.V.Borkelstraat 1312900 Schoten
Phone: +32 - 3 - 658 07 20E-Mail: [email protected]: www.halfen.be
Fax: +32 - 3 - 658 15 33
China HALFEN Construction Accessories Distribution Co.Ltd.Room 601 Tower D, Vantone CentreNo.A6 Chao Yang Men Wai StreetChaoyang District Beijing · P.R. China 100020
Phone: +86 - 10 5907 3200E-Mail: [email protected]: www.halfen.cn
Fax: +86 - 10 5907 3218
Czech Republic HALFEN s.r.o.Business Center ŠafránkovaŠafránkova 1238/1155 00 Praha 5
Phone: +420 - 311 - 690 060E-Mail: [email protected]: www.halfen.cz
Fax: +420 - 235 - 314308
France HALFEN S.A.S.18, rue Goubet75019 Paris
Phone: +33 - 1 - 445231 00E-Mail: [email protected]: www.halfen.fr
Fax: +33 - 1 - 445231 52
Germany HALFEN Vertriebsgesellschaft mbHLiebigstr. 14 40764 Langenfeld
Phone: +49 - 2173 - 970 0E-Mail: [email protected]: www.halfen.de
Fax: +49 - 2173-970 225
Italy HALFEN S.r.l. Soc. UnipersonaleVia F.lli Bronzetti N° 2824124 Bergamo
Phone: +39 - 035 - 0760711E-Mail: [email protected]: www.halfen.it
Fax: +39 - 035 - 0760799
Netherlands HALFEN b.v.Oostermaat 37623 CS Borne
Phone: +31 - 74-267 14 49E-Mail: [email protected]: www.halfen.nl
Fax: +31 - 74-2 67 26 59
Norway HALFEN ASPostboks 20804095 Stavanger
Phone: +47 - 51 82 34 00E-Mail: [email protected]: www.halfen.no
Poland HALFEN Sp. z o.o.Ul. Obornicka 28760-691 Poznan
Phone: +48 - 61 - 622 14 14E-Mail: [email protected]: www.halfen.pl
Fax: +48 - 61 - 622 14 15
Spain HALFEN SpainPLAKABETON S.L.Polígono Industrial Santa Ana c/ Ignacio Zuloaga 2028522 Rivas-Vaciamadrid
Phone: +34 916 669 181E-Mail: [email protected]: www.halfen.es
Fax: +34 916 669 661
Sweden Halfen ABVädursgatan 5412 50 Göteborg
Phone: +46 - 31 - 98 58 00E-Mail: [email protected]: www.halfen.se
Fax: +46 - 31 - 98 58 01
Switzerland HALFEN Swiss AGHertistrasse 25 8304 Wallisellen
Phone: +41 - 44 - 849 78 78E-Mail: [email protected]: www.halfen.ch
Fax: +41 - 44 - 849 78 79
United Kingdom /Ireland
HALFEN Ltd.A1/A2 Portland CloseHoughton Regis LU5 5AW
Phone: +44 - 1582 - 47 03 00E-Mail: [email protected]: www.halfen.co.uk
Fax: +44 - 1582 - 47 03 04
United States of America
HALFEN USA Inc. PO Box 18687 San Antonio TX 78218
Phone: +1 800.423.91 40E-Mail: [email protected]: www.halfenusa.com
Fax: +1 877.683.4910
For countries not listed HALFEN International
HALFEN International GmbHLiebigstr. 14 40764 Langenfeld / Germany
Phone: +49 - 2173 - 970 - 0 E-Mail: [email protected]: www.halfen.com
Fax: +49 - 2173 - 970 - 849
CONTACT HALFEN WORLDWIDE
HALFEN is represented by subsidiaries in the following countries, please contact us:
Please contact us: www.halfen.com www.dnvgl.com
© 2
018
HA
LFEN
Gm
bH, G
erm
any
appl
ies
also
to
copy
ing
in e
xtra
cts.
U -
339
- 04/
18