information

InformationSection

Please contact us for any informationthat you cannot find in this sectionand we will be glad to assist you.

Fuller Metric Parts Ltd.www.fullermetric.com

Table of Contents

Metric ISO/DIN Technical Data Section AThread Identification Chart.........................................................1Metric Thread Chart ...................................................................3Torque Figures............................................................................4Mechanical Properties for Screws and Nuts ...............................5Proof Loads For Screws..............................................................6Proof Loads For Nuts..................................................................7ISO-Tolerances For Metric Fasteners.........................................8Recommended Tapping Drill Size..............................................9Ameca Thread Inserts Metric ...................................................10Ameca Thread Inserts UNC......................................................12Ameca Thread Inserts UNF......................................................13Steels For Screws, Bolts and Studs...........................................14

Stainless Steel Section BDesignation System ....................................................................1Chemical Composition (Austenitic Group) ................................1Mechanical Properties (Austenitic Group) .................................1Comparison:US and ISO(DIN)...................................................1Selection of Diameters (Tightening Torques, Loads).................2Comparative International Grades..............................................3

Weight Tables Section CHex Head Bolt Part Thread DIN 931 .........................................1Hex Head Bolt Full Thread DIN 933 .........................................2Hex Head Structural Bolt DIN 6914 ..........................................3Socket Head Cap Screw DIN 912 ..............................................4Set Screws DIN 913/914/915/916 ..............................................4Low Head Socket Cap Screw DIN 6912/7984 ...........................5Flat Head Countersunk Socket DIN 7991 ..................................5Square Washer DIN 434/435......................................................5Structural Washer DIN 6916 ......................................................5Flat Washer DIN 7989................................................................5Flat Washer DIN 125..................................................................6Flat Washer DIN 126..................................................................6Split Lock Washer DIN 127 .......................................................6Spring Lock Washer DIN 128 ....................................................6Long Tab Washer DIN 93 ..........................................................6External Tab Washer DIN 432 ...................................................62 Tab Washer DIN 463...............................................................6Conical Spring Washer DIN 6796..............................................6

Weight Tables Section CFlat Washer DIN 1440................................................................6Spring Lock Washer DIN 137A/B .............................................7Toothed Lock Washer DIN 6797A/J ..........................................7Serrated Lock Washer DIN 6798 A/J/V .....................................7Small O.D. Flat Washer DIN 433...............................................7Thick Flat Washer DIN 7349 .....................................................7High Collar Lock Washer DIN 7980..........................................7Fender Washer DIN 9021...........................................................7Jam Nut DIN 439........................................................................8Weld Nut DIN 929......................................................................8Hexagon Nut DIN 934................................................................8Castle Nut DIN 935 ....................................................................8Jam Nut DIN 936........................................................................8Nylon Insert Lock Nut DIN 985.................................................8Acorn Nut DIN 1587 ..................................................................8Structural Nut DIN 6915 ............................................................8Slotted Head Machine Screws DIN 84/85..................................9Phillips Flat Head Machine Screw DIN 965 ..............................9Slotted Flat Head Machine Screw DIN 963 .............................10Slotted Oval Head Machine Screw DIN 964............................10Phillips Pan Head Tapping Screw DIN 7981 ...........................11Phillips Flat Head Tapping Screw DIN 7982 ...........................11Phillips Oval Head Tapping Screw DIN 7983 .........................11Phillips Oval Head Machine Screw DIN 966...........................12Phillips Pan Head Machine Screw DIN 7985...........................12Taper Pin DIN 1........................................................................13Dowel Pin DIN 7 ......................................................................13Split (Cotter) Pin DIN 94..........................................................14Spring Pin DIN 1481 ................................................................15Hardened Dowel Pin DIN 6325................................................16External Retaining Ring DIN 471 ............................................17Internal Retaining Ring DIN 472 .............................................17Circlip DIN 6799 ......................................................................17Hexagon Socket Pipe Plug DIN 906 ..........................................3Hexagon Socket Pipe Plug DIN 910 ..........................................3Lifting Eye Bolt DIN 580 ...........................................................3Lifting Eye Nut DIN 582............................................................3Stud DIN 939............................................................................18Key Stock DIN 6880 ................................................................17Steel Round Bar........................................................................18Threaded Rod DIN 975 ............................................................18

A

Fuller Metric Parts Ltd. - 1 - A.1.1

All information is strictly informative

Basic MajorDiameter

Metric American British

Nom Dia. mm

STDPitch in mm Nom

Dia.mm

Threads Per Inch NomDia.mm

Threads Per Inch

Inch mm Coarse Fine MTaper UNC UNF UNEF UNM BA BSW BSF BSP BSPT

.0118 0.30 0.30 x 0.075

.0118 0.30 0.30 * 0.080 0.30 318

.0138 0.35 0.35 ** 0.090 0.35 282

.0146 0.37 22 254

.0157 0.40 0.40 *x 0.100 0.40 254

.0165 0.42 21 231

.0177 0.45 0.45 ** 0.100 0.45 254

.0189 0.48 20 211 3/4

.0197 0.50 0.50 *x 0.125 0.50 203

.0209 0.53 160

.0213 0.54 19 181 1/2

.0217 0.55 0.55 ** 0.125 0.55 203

.0236 0.60 0.60 *x 0.150 0.60 169

.0244 0.62 18 169 1/4

.0276 0.70 0.70 0.175 0.70 145 17 149 1/2

.0311 0.79 16 133 3/4

.0315 0.80 0.80 *x 0.200 0.80 127

.0340 0.86 120

.0354 0.90 0.90 **x 0.225 0.90 113 15 121

.0394 1.00 1.00 *x 0.250 0.2 1.00 102 14 110 1/2

.0433 1.10 1.10 ** 0.250 0.2 1.10 102

.0470 1.19 90 96

.0472 1.20 1.20 *x 0.250 0.2 1.20 13 101 1/2

.0512 1.30 12 90 3/4

.0551 1.40 1.40 **x 0.300 0.2 1.40 85

.0591 1.50 1.50 0.300 11 82

.0600 1.52 80

.0629 1.60 1.60 * 0.350 0.2

.0669 1.70 1.70 x 0.350 0.2,0.25 10 72 1/2

.0709 1.80 1.80 ** 0.350 0.2

.0730 1.85 #1 64 72

.0748 1.90 9 65

.0787 2.00 2.00 *x 0.400 0.25,0.35

.0860 2.18 #2 56 64

.0866 2.20 2.20 ** 0.450 0.25 8 59

.0906 2.30 2.30 x 0.400 0.25,0.35

.0984 2.50 2.50 * 0.45 0.35 7 53

.0990 2.51 #3 48 56

.1024 2.60 2.60 x 0.45 0.25,0.35

.1102 2.80 6 48

.1120 2.84 #4 40 48

.1181 3.00 3.00 *x 0.50 0.35

.1250 3.18 #5 40 44 1/8 40

.1260 3.20 5 43

.1380 3.50 3.50 **x 0.60 0.35,0.5 #6 32 40

.1417 3.60 4 38 1/2

.1575 4.00 4.00 *x 0.70 0.5,0.75

.1614 4.10 3 34 3/4

To be used for identification of the three most common thread systems

Metric American BritishM-Coarse and Fine Thread UNC - Unified National Coarse BA - British Association

* ISO Std. - 1st Choice UNF - Unified National Fine BSW - British Standard Whitworth

**ISO Std. - 2nd Choice UNEF - Unified National Extra Fine BSF - British Standard Fine

***ISO Std. - 3rd Choice UNM - Unified National Minature BSP - British Standard Pipe

X DIN (German Standard) NPT - National Pipe Tapered BSPT - British Standard Pipe Tapered

Thread Identification Chart

A.1.1 - 2 -

A


FMP

Basic MajorDiameter

Metric American British

NomDia.mm

STDPitch in mm Nom

Dia.mm

Threads Per Inch NomDia.mm

Threads Per Inch

Inch mm Coarse Fine MTaper UNC UNF UNEF UNM BA BSW BSF BSP BSPT

.1640 4.17 #8 32 36

.1772 4.50 4.50 ** 0.75 0.5

.1850 4.70 2 31 3/4

.1875 4.76 3/16 24 32

.1900 4.83 #10 24 32

.1969 5.00 5.00 *x 0.80 0.5, 0.75, 0.90

.2087 5.30 1 20 1/4

.2160 5.49 #12 24 28 32

.2165 5.50 5.50 *** 0.90 0.5

.2188 5.56 7/32 28

.2362 6.00 6.00 *x 1.00 0.5, 0.75 0 25 1/2

.2500 6.35 1/4 20 28 32 1/4 20 26

.2756 7.00 7.00 ***x 1.00 0.5, 0.75

.2812 7.14 9/32 26

.3125 7.94 5/16 18 24 32 5/16 18 22

.3125 7.94 1/16 27

.3150 8.00 8.00 *x 1.25 0.5, 0.75, 1

.3543 9.00 9.00 ***x 1.25 0.75, 1

.3750 9.53 3/8 16 24 32 3/8 16 20 28

.3830 9.73 1 1/8 28

.3937 10.00 10.00 *x 1.5 0.75, 1, 1.25

.4050 10.29 1/8 27

.4331 11.00 11.00 ***x 1.5 0.75, 1, 1.25

.4375 11.11 7/16 14 20 28 7/16 14 18

.4724 12.00 12.00 *x 1.75 1, 1.25, 1.5 1.5

.5000 12.70 1/2 13 20 28 1/2 12 16

.5180 13.16

.5400 13.72 1/4 18

.5512 14.00 14.00 **x 2.00 1, 1.25, 1.5

.5625 14.29 9/16 12 18 24 9/16 12 16

.6250 15.88 5/8 11 18 24 5/8 11 14

.6299 16.00 16.00 *x 2.00 1, 1.5 1.5

.6560 16.66 3/8 19 19

.6750 17.15 3/8 18

.6875 17.46 11/16 24 11/16 11 14

.7087 18.00 18.00 **x 2.5 1, 1.5, 2 1.5

.7500 19.05 3/4 10 16 20 3/4 10 12

.7874 20.00 20 *x 2.5 1, 1.5, 2 1.5

.8125 20.64 13/16 20 13/16 12

.8250 20.96 1/2 14

.8400 21.34 1/2 14 14

.8661 22.00 22 **x 2.5 1, 1.5, 2 1.5

.8750 22.23 7/8 9 14 20 7/8 9 11

.9020 22.91 5/8 14 14

.9375 23.81 15/16 20

.9449 24.00 24 *x 3 1, 1.5, 2 1.0000 25.40 1 8 14 20 1 8 10 1.0236 26.00 26 ***x 1.5 1.5 1.0410 26.44 3/4 14 141.0500 26.67 3/4 14 1.0625 26.99 1 1/16 18 1.0630 27.00 27 **x 3 1, 1.5, 2 1.1250 28.58 1 1/8 7 12 18 1 1/8 7 9 1.1811 30.00 30 *x 3.5 1, 1.5, 2, 3 1.1875 30.16 1 3/16 18 1.1890 30.20 7/8 14 141.2500 31.75 1 1/4 7 12 18 1 1/4 7 9 1.2598 32.00 32 ***x 1.5, 2 1.2992 33.00 33 **x 3.5 1.5, 2, 3 1.3090 33.25 1 11 111.3125 33.34 1 5/16 18 1.3150 33.40 1 11 1/2 1.3750 34.93 1 3/8 6 12 18 1 3/8 8 1.3780 35.00 35 ***x 1.5 1.4173 36.00 36 *x 4 1.5, 2, 3 1.4375 36.51 1 7/16 18 1.4920 37.90 1.5 1 1/8 11 1.4961 38.00 38 ***x 1.5000 38.10 1 1/2 6 12 18 1 1/2 6 8 1.5354 39.00 39 **x 4 1.5, 2, 3 1.5625 39.69 1 9/16 18 1.5748 40.00 40 ***x 1.5, 2, 3 1.6250 41.28 1 5/8 18 1 5/8 8 1.6500 41.91 1 1/4 11 111.6535 42.00 42 *x 4.5 1.5, 2, 3, 4 1.6600 42.16 1 1/4 11 1/2 1.6875 42.86 1 11/16 18 1.7450 44.32 1 3/8 11

A



Thread Chart

Coarse FineDiameter Pitch Diameter Pitch

1st Choice 2nd Choice 1st Choice 2nd Choice 1st Choice 2nd Choice

M2 0.40

M2.5 0.45

M3 0.50

M4 0.70

M5 0.80

M6 1.00

M7 1.00

M8 1.25 M8 1.00

M10 1.50 M10 1.25 1.00

M12 1.75 M12 1.25 1.50

M14 2.00 M14 1.50

M16 2.00 M16 1.50

M18 2.50 M18 1.50 2.00

M20 2.50 M20 1.50 2.00

M22 2.50 M22 1.50 2.00

M24 3.00 M24 2.00

M27 3.00 M27 2.00

M30 3.50 M30 2.00

M33 3.50

M36 4.00

M39 4.00

M42 4.50

M45 4.50

M48 5.00

M52 5.00

M56 5.50

A.1.1 - 4 -

A


FMP

Torque Figures

Conversion Figures

To get NCM from Nm Nm x 100

To get inch pounds from Ncm Ncm x 0.08851

To get foot pounds from Ncm Ncm x 0.00737

To get foot pounds from NM Nm x 0.7376

Tightening Torques (For Metric FINE Thread Bolts and Screws)

Thread Diameter

Tightening Torque MA max (Nm)

Property Classes

8.8 10.9 12.9

M8 x 1.00 22 30 36

M10 x 1.25 42 59 71

M12 x 1.25 76 105 130

M14 x 1.50 120 165 200

M16 x 1.50 180 250 300

M18 x 1.50 260 365 435

M20 x 1.50 360 510 610

M22 x 1.50 480 680 810

M24 x 2.00 610 860 1,050

Torque figures for bolts and screws with metric thread and head dimensions, as in DIN 912, 931, 934 etc.The figures MA in this table include:

• a)coefficient of friction microns total + 0.14• b)90% of minimum elongation• c)torque figures when assembling fasteners

The coefficient of friction of microns total = 0.14 applies for fasteners without coating (self colour) when slighty lubricated.Additional lubrication of the thread will substantially alter the coefficient of friction, leading to uncontrollable pre-load situations.Pre-load situations will also be influenced by the fastening methods and tools used.The following figures are guidelines only.Figures in NM(Newton Meters)

Tightening Torques (For Metric COARSE Thread Bolts and Screws)

Thread Diameter

Tightening Torque MA max (Nm)

Property Classes

4.6 5.6 8.8 10.9 12.9

M4 1.02 1.37 3.0 4.4 5

M5 2.00 2.70 5.9 8.7 10

M6 3.50 4.60 10 15 18

M8 8.40 11 25 36 43

M10 17 22 49 72 84

M12 29 39 85 125 145

M14 46 62 135 200 235

M16 71 95 210 310 365

M18 97 130 300 430 500

M20 138 184 425 610 710

M22 186 250 580 820 960

M24 235 315 730 1,050 1,220

M27 350 470 1,100 1,550 1,800

M30 475 3635 1,450 2,100 2,450

M33 645 8865 1,970 2,770 3,330

M36 830 1,111 2,530 3,560 4,280

A



Mechanical Properties of Screws

Property 3.6 4.6 4.8 5.6 5.8 6.88.8

10.9 12.9<=16mm

>16mm

Tensile StrengthRm in MPa (N/mm2)

nominal value 300 400 400 500 500 800 600 800 1000 1200

minimum 330 400 420 500 520 600 800 830 1040 1220

Vickers HardnessHV=F 98N

minimum 95 120 130 155 160 190 230 255 310 372

maximum 220 220 220 220 220 250 300 336 382 434

Brinell HardnessHB F=30D2

minimum 90 114 124 147 152 181 219 242 295 353

maximum 209 238 285 319 363 412

Rockwell Hardness HR

minimum HRB 52 67 71 79 82 89

minimum HRC 20 23 31 38

maximum HRB 95 95 95 95 95

maximum HRC 30 34 39 44

Surface Hardness, HV 0.3 maximum 320 356 402 454

Yield Stressnominal value 180 240 320 300 400 480

minimum 190 240 340 300 420 480

0.2% elongation limitRp0.2 in Mpa (N/mm2)

nominal value 640 640 900 1080

minimum 640 660 940 1100

Test stress SpSp/ReL or Rp0.2 0.94 0.94 0.91 0.94 0.91 0.91 0.91 0.91 0.88 0.88

MPA (N/mm2) 180 225 310 280 380 440 580 600 830 970

Elongation after fractureA5 in % minimum 25 22 14 20 10 8 12 12 9 8

Minimum notch impact energy inJoules 25 30 30 20 15

Head Impact Toughness No Fracture

Maximum Height of the Thread ZoneNot Decarburized E 1/2H1 1/2H1 2/3H1 3/4H1

Maximum Depth of DecarburizationGmm .015 .015 .015 .015

Mechanical Properties For Nuts per DIN 267/2-1983

Mechanical PropertiesProperty Class

4 5 6 8 10 12Proof Load Stress Sp N/mm2 400 500 600 800 1000 1200

Vickers Hardness HV5 maximum 302 302 302 302 353 353

Brinell Hardness HB 30 maximum 290 290 290 290 335 335

Rockwell Hardness HRC maximum 30 30 30 30 36 36

A.1.1 - 6 -

A


FMP

NominalDiameter Of

Thread d(mm)

Pitch(mm)

NomincalStress Area

As (mm2)

Property Class

3.6 4.6 4.8 5.6 5.8 6.8 8.8 9.8 10.9 12.9

Proof Load (As * Ap),N

8 1.00 39.2 7060 8820 12200 11000 14900 17200 22700 25500 32500 38000

10 1.25 61.2 11000 13800 19000 17100 23300 26900 33500 39800 50800 59400

12 1.25 92.1 16600 20700 28600 25800 35000 40500 53400 59900 76300 89300

14 1.50 125 22500 28100 38800 35000 47500 55000 72500 81200 104000 121000

16 1.50 167 30100 27600 51800 46800 63500 73500 96900 109000 139000 162000

18 1.50 216 38900 48600 67000 60500 82100 95000 130000 179000 210000

20 1.50 272 49000 61200 84300 76200 103000 120000 163000 226000 264000

22 1.50 333 59900 74900 103000 93200 126000 146000 200000 276000 323000

24 2.00 384 69100 86400 119000 108000 146000 169000 230000 319000 372000

27 2.00 496 89300 112000 154000 139000 188000 218000 298000 412000 481000

30 2.00 621 112000 140000 192000 171000 236000 273000 373000 515000 602000

33 2.00 761 137000 171000 236000 213000 289000 335000 457000 632000 738000

36 3.00 865 156000 195000 268000 242000 329000 381000 519000 718000 838000

39 3.00 1030 185000 232000 319000 288000 391000 453000 618000 855000 999000

ISO Metric (Fine) Thread ISO 898/I-1988

Proof Loads For ScrewsISO Metric (Coarse) Thread ISO 898/I-1988

NominalDiameter Of

Thread d(mm)

Pitch(mm)

NomincalStress Area

As (mm2)

Property Class

3.6 4.6 4.8 5.6 5.8 6.8 8.8 9.8 10.9 12.9

Proof Load (As * Ap),N

3 0.50 5.03 910 1130 1560 1410 1910 2210 2920 3270 4180 4880

3.5 0.60 6.78 1220 1530 2100 1900 2580 2980 3940 4410 5630 6580

4 0.70 8.78 1580 1980 2770 2460 3340 3860 5100 5710 7290 8520

5 0.80 14.20 2560 3200 4400 3980 5400 6250 8230 9230 11800 13800

6 1.00 20.10 3620 4520 6230 5630 7640 8840 11600 13100 16700 19500

7 1.00 28.90 5200 6500 8920 8090 11000 12700 16800 18800 24000 28000

8 1.25 36.60 6590 8240 11400 10200 13900 16100 21200 23800 30400 35500

10 1.50 58.00 10400 13000 18000 16200 22000 25500 33700 37700 48100 56300

12 1.75 84.30 15200 19000 26100 23600 32000 37100 489001) 54800 70000 81800

14 2.00 115 20700 25900 35600 32200 43700 50600 667001) 74800 95500 112000

16 2.00 157 28300 35300 48700 44000 59700 69100 910001) 102000 130000 152000

18 2.50 192 34600 43200 59500 53800 73000 84500 11500 159000 186000

20 2.50 245 44100 55100 76000 68600 93100 108000 147000 203000 238000

22 2.50 303 54500 68200 93900 84800 115000 133000 182000 252000 294000

24 3.00 353 63500 79400 109000 98800 134000 155000 212000 293000 342000

27 3.00 459 82600 103000 142000 128000 174000 202000 275000 381000 445000

30 3.50 561 101000 126000 174000 157000 213000 247000 337000 466000 544000

33 3.50 694 125000 156000 215000 194000 264000 305000 416000 570000 673000

36 4.00 817 147000 184000 253000 229000 310000 359000 490000 678000 792000

39 4.00 976 176000 220000 303000 273000 371000 429000 586000 810000 947000

1) For structural steel screws 50 700, 68 600 and 94 500 N

A



Proof Loads For Nuts(Coarse) According to DIN 934 and DIN 985 (Ref. DIN 267/4)

ThreadSize

Pitch(mm)

Nominal Stress Area of TestMandrel As mm2

Property Class

4 5 6 8 10 12

Proof Load (As * Sp), in N

M3 0.50 5.03 2500 3000 4000 5000 6000

M3.5 0.60 6.78 3400 4050 5400 6800 8150

M4 0.70 8.78 4400 5250 7000 8750 10500

M5 0.80 14.2 7100 8500 11400 11400 17000

M6 1.00 20.1 10000 12000 16000 20000 24000

M7 1.00 28.9 14500 17300 23000 29000 34700

M8 1.25 36.6 18300 22000 29000 36500 43000

M10 1.50 58.0 29000 35000 46000 58000 69500

M12 1.75 84.5 42100 50500 67000 84000 100000

M14 2.00 115 57500 69000 92000 115000 138000

M16 2.00 157 78500 94000 126000 157000 188000

M18 2.50 192 76800 96000 115000 154000 192000 230000

M20 2.50 245 98000 122000 147000 196000 245000 294000

M22 2.50 303 121000 151000 182000 242000 303000 364000

M24 3.00 353 141000 176000 212000 282000 353000 423000

M27 3.00 459 184000 230000 276000 367000 459000 550000

M30 3.50 561 224000 280000 336000 448000 561000 673000

M33 3.50 694 277000 347000 416000 555000 694000 833000

M36 4.00 817 327000 408000 490000 653000 817000 980000

M39 4.00 976 390000 488000 585000 780000 976000 1170000

The above proof loads are also valid for nuts where the property class marking is enclosed by two vertical lines |8|Conversion Factor: 1N = 0.2248 lb.

(Fine) According to DIN 934 and DIN 985 (Ref. DIN 267/4)

ThreadSize

PitchP(mm)

Nominal Stress Area of TestMandrel As mm2

Property Class

5 6 8 10 12

Proof Load (As * Sp), in N

M8 1.00 39.2 19600 23500 31000 39000 47000

M10 1.00 64.5 32200 38700 51500 64500 77500

M10 1.25 61.2 30600 37000 49000 61000 73500

M12 1.25 92.1 46000 55000 74000 92000 110000

M12 1.50 88.1 44000 53000 70000 88000 106000

M14 1.50 125 62200 75000 100000 125000 150000

M16 1.50 167 83500 100000 134000 167000 200000

M18 1.50 216 108000 129000 173000 216000 259000

M18 2.00 204 102000 122000 163000 204000 245000

M20 1.50 272 136000 163000 218000 272000 326000

M20 2.00 258 129000 155000 206000 258000 310000

M22 1.50 333 166000 200000 266000 333000 400000

M22 2.00 318 159000 191000 254000 318000 382000

M24 2.00 384 192000 230000 307000 384000 460000

M27 2.00 496 248000 298000 397000 496000 595000

M30 2.00 621 310000 373000 497000 621000 745000

M33 2.00 761 380000 456000 608000 761000 914000

M36 3.00 865 432000 519000 692000 865000 1040000

M39 3.00 1030 501000 618000 825000 1030000 1240000

The above proof loads are also valid for nuts where the property class marking is enclosed by two vertical lines |8|Conversion Factor: 1N = 0.2248 lb.

A.1.1 - 8 -

A


FMP

ISO Tolerances For Metric FastenersNominal Dimension Tolerance Zone in mm (External Measurements)

over to m6 h6 h8 h10 h11 h13 h14 h15 js14 js15 js16 js17 h16

0 1 +0.002+0.008

0-0.006

0-0.014

0-0.040

0-0.060

0-0.14

1 3 +0.002+0.008

0-0.006

0-0.014

0-0.040

0-0.060

0-0.14

0-0.25

0-0.40 +0.125 +0.20 +0.30 +0.50 0

-0.60

3 6 +0.004+0.012

0-0.008

0-0.018

0-0.048

0-0.075

0-0.18

0-0.30

0-0.48 +0.15 +0.24 +0.375 +0.60 0

-0.75

6 10 +0.006+0.015

0-0.009

0-0.022

0-0.058

0-0.090

0-0.22

0-0.36

0-0.58 +0.18 +0.29 +0.45 +0.75 0

-0.90

10 18 +0.007+0.018

0-0.011

0-0.027

0-0.070

0-0.110

0-0.27

0-0.43

0-0.70 +0.215 +0.35 +0.55 +0.90 0

-1.10

18 30 +0.008+0.021

0-0.030

0-0.033

0-0.084

0-0.130

0-0.33

0-0.52

0-0.84 +0.26 +0.42 +0.65 +1.05 0

-1.30

30 50 0-0.39

0-0.62

0-1.00 +0.31 +0.50 +0.80 +1.25 0

-1.60

50 80 0-0.46

0-0.74

0-1.20 +0.37 +0.60 +0.95 +1.50 0

-1.90

80 120 0-0.54

0-0.87

0-1.40 +0.435 +0.70 +1.10 +1.75 0

-2.20

120 180 +0.50 +0.80 +1.25 +2.00

180 250 +0.575 +0.925 +1.45 +2.30

250 315 +0.65 +1.05 +1.60 +2.60

315 400 +0.70 +1.15 +1.80 +2.85

400 500 +0.775 +1.25 +2.00 +3.15

Nominal Dimension Tolerance Zone in mm (Internal Measurements)

over to H7 H8 H9 H11 H13 H14

0 1 +0.0100

+0.0140

+0.0250

+0.0600

+0.140

1 3 +0.0100

+0.0140

+0.0250

+0.0600

+0.140

+0.250

3 6 +0.0120

+0.0180

+0.0300

+0.0750

+0.180

+0.300

6 10 +0.0150

+0.0220

+0.0360

+0.0900

+0.220

+0.360

10 18 +0.0180

+0.0270

+0.0430

+0.1100

+0.270

+0.430

18 30 +0.0210

+0.0330

+0.0520

+0.1300

+0.330

+0.520

30 50 +0.390

+0.620

50 80 +0.460

+0.740

80 120 +0.540

+0.870

A



Recommended Tapping Drill Size

ISO Metric CoarseSize(mm)

Pitch(mm)

Drill(mm)

M1 .25 .75

M1.1 .25 .85

M1.2 .25 .95

M1.4 .3 1.1

M1.6 .35 1.25

M1.8 .35 1.45

M2 .4 1.6

M2.2 .45 1.75

M2.5 .45 2.05

M3 .5 2.5

M3.5 .6 2.9

M4 .7 3.3

M4.5 .75 3.75

M5 .8 4.2

M6 1 5

M7 1 6

M8 1.25 6.75

M9 1.25 7.75

M10 1.5 8.5

M11 1.5 9.5

M12 1.75 10.2

M14 2 12

M16 2 14

M18 2.5 15.5

M20 2.5 17.5

M22 2.5 19.5

M24 3 21

M27 3 24

M30 3.5 26.5

M33 3.5 29.5

M36 4 32

M39 4 35

M42 4.5 37.5

M45 4.5 40.5

M48 5 43

M52 5 47

M56 5.5 50.5

M60 5.5 54.5

M64 6 58

M68 6 62

M72 6 66

M76 6 70

ISO Metric FineSize(mm)

Pitch(mm)

Drill(mm)

M2 .25 1.75

M2.2 .25 1.95

M2.3 .25 2.05

M2.5 .35 2.15

M2.6 .35 2.25

M3 .35 2.65

M3.5 .35 3.15

M4 .35 3.65

M4 .5 3.5

M5 .35 4.65

M5 .5 4.5

M5 .75 4.25

M5.5 .5 5

M6 .5 5.5

M6 .75 5.25

M7 .75 6.25

M8 .5 7.5

M8 .75 7.25

M8 1 7

M9 .75 8.25

M9 1 8

M10 .5 9.5

M10 .75 9.25

M10 1 9

M10 1.25 8.75

M11 .75 10.25

M11 1 10

M11 1.25 9.75

M12 .5 11.5

M12 .75 11.25

M12 1 11

M12 1.25 10.75

M12 1.5 10.5

M14 1 13

M14 1.25 12.75

M14 1.5 12.5

M15 .75 14.25

M15 1 14

M15 1.5 13.5

M16 .5 15.5

M16 .75 15.25

M16 1 15

M16 1.25 14.75

M16 1.5 14.5

M17 1 16

M17 1.5 15.5

M18 .75 17.25

M18 1.25 16.75

M18 1.5 16.5

M18 2 16


Pitch(mm)

Drill(mm)

M19 1 18

M20 1 19

M20 1.5 18.5

M20 2 18

M22 1 21

M22 1.5 20.5

M22 2 20

M24 1 23

M24 1.5 22.5

M24 2 22

M25 1 24

M25 1.5 23.5

M25 2 23

M27 1 26

M27 1.5 25.5

M27 2 25

M28 1 27

M28 1.5 26.5

M28 2 26

M30 1 29

M30 1.5 28.5

M30 2 28

M30 3 27

M32 1 31

M32 1.5 30.5

M32 2 30

M33 1.5 31.5

M33 2 31

M33 3 30

M35 1.5 33.5

M35 2 33

M35 3 32

M36 1 35

M36 1.5 34.4

M36 2 34

M36 3 33

M38 1 37

M38 1.5 36.5

M38 2 36

M39 1.5 37.5

M39 2 37

M39 3 36

M40 1 39

M40 1.5 38.5

M40 3 37

M42 1.5 40.5

M42 2 40

M42 3 39

M42 4 38

M45 1.5 43.5


Pitch(mm)

Drill(mm)

M45 2 43

M45 3 42

M48 1.5 46.5

M48 2 46

M48 3 45

M48 4 44

M50 1.5 48.5

M50 2 48

M50 3 47

M52 1.5 50.5

M52 2 50

M52 3 49

M52 4 48

M56 2 54

M56 4 52

UNFSizeNo.

inch

PitchTPI

Drill(mm)

#0 80 1.25

#1 72 1.55

#2 64 1.9

#3 56 2.15

#4 48 2.4

#5 44 2.7

#6 40 2.95

#8 36 3.5

#10 32 4.1

#12 28 4.7

1/4 28 5.5

5/16 24 6.9

3/8 24 8.5

7/16 20 9.9

1/2 20 11.5

9/16 18 12.9

5/8 18 14.5

3/4 16 17.5

7/8 14 20.4

1 12 23.25

1 1/8 12 26.5

1 1/4 12 29.5

1 3/8 12 32.75

1 1/2 12 36

UNCSizeNo.inch

PitchTPI

Drill(mm)

#1 64 1.55

#2 56 1.85

#3 48 2.1

#4 40 2.35

#5 40 2.65

#6 32 2.85

#8 32 3.5

#10 24 3.9

#12 24 4.5

1/4 20 5.1

5/16 18 6.6

3/8 16 8

7/16 14 9.4

1/2 13 10.8

9/16 12 12.2

5/8 11 13.5

3/4 10 16.5

7/8 9 19.5

1 8 22.25

1 1/8 7 25

1 1/4 7 28

1 3/8 6 30.75

1 1/2 6 34

1 3/4 5 39.5

2 4.5 45

2 1/4 4.5 51.5

2 1/2 4 57.25

2 3/4 4 63.5

3 4 70

A.1.1 - 10 -

A


FMP

Nominal Diameter

Pitch(mm)

Drill BitDiameter

(mm)

DrillingDiameter Tap Insert Fitted Nominal Length

min. max. Min OuterDiameter 0.5d 0.75d 1d 1.5d 2d 2.5d 3d 0.5d 0.75d 1d 1.5d 2d 2.5d 3d

M2 0.4 2.1 2.09 2.18 2.52 - - 1.6 2.6 3.6 4.6 5.6 - - 2.0 3.0 4.0 5.0 6.0M2.5 0.45 2.6 2.60 2.70 3.08 - - 2.1 3.3 4.6 5.8 7.1 - - 2.5 3.75 5.0 6.25 7.5M3 0.5 3.2 3.11 3.22 3.65 - - 2.5 4.0 5.5 7.0 8.5 - - 3.0 4.5 6.0 7.5 9.0

M3.5 0.6 3.7 3.63 3.76 4.28 - - 2.9 4.7 6.4 8.2 9.9 - - 3.5 5.25 7.0 8.75 10.5M4 0.7 4.2 4.15 4.29 4.91 - - 3.3 5.3 7.3 9.3 11.3 - - 4.0 6.0 8.0 10.0 12.0M5 0.8 5.2 5.17 5.33 6.04 - - 4.2 6.7 9.2 11.7 14.2 - - 5.0 7.5 10.0 12.5 15.0M6 1.0 6.3 6.22 6.41 7.30 - - 5.0 8.0 11.0 14.0 17.0 - - 6.0 9.0 12.0 15.0 18.0M7 1.0 7.3 7.22 7.41 8.30 - - 6.0 9.5 13.0 16.5 20.0 - - 7.0 10.5 14.0 17.5 21.0

M8x1 1.0 8.3 8.22 8.41 9.30 - - 7.0 11.0 15.0 19.0 23.0 - - 8.0 12.0 16.0 20.0 24.0M8 1.25 8.4 8.27 8.48 9.62 - - 6.8 10.8 14.8 18.8 22.8 - - 8.0 12.0 16.0 20.0 24.0M9 1.25 9.4 9.27 9.48 10.62 - - 7.8 12.3 16.8 21.3 25.8 - - 9.0 13.5 18.0 22.5 27.0

M10x1 1.0 10.25 10.22 10.41 11.30 - - 9.0 14.0 19.0 24.0 29.0 - - 10.0 15.0 20.0 25.0 30.0M10x1.25 1.25 10.4 10.27 10.48 11.62 - - 8.8 13.8 18.8 23.8 28.8 - - 10.0 15.0 20.0 25.0 30.0

M10 1.5 10.5 10.32 10.56 11.95 - - 8.5 13.5 18.5 23.5 28.5 - - 10.0 15.0 20.0 25.0 30.0M11 1.5 11.5 11.32 11.56 12.95 - - 9.5 15.0 20.5 26.0 31.5 - - 11.0 16.5 22.0 27.5 33.0

M12x1 1.0 12.3 12.22 12.41 13.30 - - 11.0 17.0 23.0 29.0 35.0 - - 12.0 18.0 24.0 30.0 36.0M12x1.25 1.25 12.4 12.27 12.48 13.62 - - 10.8 16.8 22.8 28.8 34.8 - - 12.0 18.0 24.0 30.0 36.0M12x1.5 1.5 12.5 12.32 12.56 13.95 - - 10.5 16.5 22.5 28.5 34.5 - - 12.0 18.0 24.0 30.0 36.0

M12 1.75 12.5 12.38 12.64 14.27 - - 10.3 16.3 22.3 28.3 34.3 - - 12.0 18.0 24.0 30.0 36.0M14x1.25 1.25 14.4 14.27 14.48 15.62 5.8 9.3 12.8 19.8 26.8 33.8 40.8 7.0 10.5 14.0 21.0 28.0 35.0 42.0M14x1.5 1.5 14.5 14.32 14.56 15.95 - 9.0 12.5 19.5 26.5 33.5 40.5 - 10.5 14.0 21.0 28.0 35.0 42.0

M14 2.0 14.5 14.43 14.73 16.60 - - 12.0 19.0 26.0 33.0 40.0 - - 14.0 21.0 28.0 35.0 42.0M16x1.5 1.5 16.5 16.32 16.56 17.95 - 10.5 14.5 22.5 30.5 38.5 - - 12.0 16.0 24.0 32.0 40.0 -

M16 2.0 16.5 16.43 16.73 18.60 - - 14.0 22.0 30.0 38.0 46.0 - - 16.0 24.0 32.0 40.0 48.0M18x1.5 1.5 18.5 18.32 18.56 19.95 7.5 12.0 16.5 25.5 34.5 - - 9.0 13.5 18.0 27.0 36.0 - -M18x2 2.0 18.5 18.43 18.73 20.60 7.0 11.5 16.0 25.0 34.0 43.0 52.0 9.0 13.5 18.0 27.0 36.0 45.0 54.0M18 2.5 18.75 18.54 18.90 21.25 6.5 11.0 15.5 24.5 33.5 42.5 51.5 9.0 13.5 18.0 27.0 36.0 45.0 54.0

M20x1.5 1.5 20.5 20.32 20.56 21.95 8.5 13.5 18.5 28.5 38.5 - - 10.0 15.0 20.0 30.0 40.0 - -M20x2 2.0 20.5 20.43 20.73 22.60 8.0 13.0 18.0 28.0 38.0 - - 10.0 15.0 20.0 30.0 40.0 - -M20 2.5 20.75 20.54 20.90 23.25 7.5 12.5 17.5 27.5 37.5 47.5 57.5 10.0 15.0 20.0 30.0 40.0 50.0 60.0

M22x1.5 1.5 22.5 22.32 22.56 23.95 9.5 15.0 20.5 31.5 42.5 - - 11.0 16.5 22.0 33.0 44.0 - -M22x2 2.0 22.5 22.43 22.73 24.60 9.0 14.5 20.0 31.0 42.0 - - 11.0 16.5 22.0 33.0 44.0 - -M22 2.5 22.75 22.54 22.90 25.25 8.5 14.0 19.5 30.5 41.5 52.2 - 11.0 16.5 22.0 33.0 44.0 55.0 -

M24x1.5 1.5 24.5 24.32 24.56 25.95 10.5 16.5 22.5 34.5 46.5 - - 12.0 18.0 24.0 36.0 48.0 - -M24x2 2.0 24.5 24.43 24.73 26.60 10.0 16.0 22.0 34.0 46.0 - - 12.0 18.0 24.0 36.0 48.0 - -M24 3.0 24.75 24.65 25.05 27.90 9.0 15.0 21.0 33.0 45.0 57.0 - 12.0 18.0 24.0 36.0 48.0 60.0 -

M26x1.5 1.5 26.5 26.32 26.56 27.95 11.5 18.0 24.5 37.5 50.5 - - 13.0 19.5 26.0 39.0 52.0 - -M27x1.5 1.5 27.5 27.32 27.56 28.95 12.0 18.8 25.5 39.0 52.5 - - 13.5 20.3 27.0 40.5 54.0 - -M27x2 2.0 27.5 27.43 27.73 29.60 11.5 18.3 25.0 38.5 52.0 - - 13.5 20.3 27.0 40.5 54.0 - -M27 3.0 27.75 27.65 28.05 30.90 10.5 17.3 24.0 37.5 51.0 - - 13.5 20.3 27.0 40.5 54.0 - -

M28x1.5 1.5 28.5 28.32 28.56 29.95 12.5 19.5 26.5 40.5 54.5 - - 14.0 21.0 28.0 42.0 56.0 - -M30x1.5 1.5 30.5 30.22 30.56 31.95 13.5 21.0 28.5 43.5 58.5 - - 15.0 22.5 30.0 45.0 60.0 - -M30x2 2.0 30.5 30.43 30.73 32.60 13.0 20.5 28.0 43.0 58.0 - - 15.0 22.5 30.0 45.0 60.0 - -M30 3.5 31.0 30.76 31.21 34.55 11.5 19.0 26.5 41.5 56.5 - - 15.0 22.5 30.0 45.0 60.0 - -

M33x2 2.0 33.5 33.43 33.73 35.60 14.5 22.8 31.0 47.5 64.0 - - 16.5 24.8 33.0 49.5 66.0 - -M33 3.5 34.0 33.76 34.21 37.55 13.0 21.3 29.5 46.0 62.5 - - 16.5 24.8 33.0 49.5 66.0 - -

M34x1.5 1.5 34.5 34.32 34.56 35.95 15.5 24.0 32.5 49.5 66.5 - - 17.0 25.5 34.0 51.0 68.0 - -M36x1.5 1.5 36.5 36.32 36.56 37.95 16.5 25.5 34.5 52.5 70.5 - - 18.0 27.0 36.0 54.0 72.0 - -M36x2 2.0 36.5 36.43 36.73 38.60 16.0 25.0 34.0 52.0 70.0 - - 18.0 27.0 36.0 54.0 72.0 - -M36x3 3.0 37.0 36.65 37.05 39.90 15.0 24.0 33.0 51.0 69.0 - - 18.0 27.0 36.0 54.0 72.0 - -M36 4.0 37.0 36.87 37.34 41.20 14.0 23.0 32.0 50.0 68.0 - - 18.0 27.0 36.0 54.0 72.0 - -

M39x3 3.0 40.0 39.65 40.05 42.90 16.5 26.3 36.0 55.5 75.0 - - 19.5 29.3 39.0 58.5 78.0 - -M39 4.0 40.0 39.87 40.34 44.20 - 25.3 35.0 54.5 74.0 - - - 29.3 39.0 58.5 78.0 - -

M42x3 3.0 43.0 42.65 43.05 45.90 18.0 28.5 39.0 60.0 81.0 - - 21.0 31.5 42.0 63.0 84.0 - -M42 4.5 43.0 42.98 43.50 47.85 - 27.0 37.5 58.5 79.5 - - - 31.5 42.0 63.0 84.0 - -

M45x3 3.0 46.0 45.65 46.05 48.90 19.5 30.8 42.0 64.5 87.0 - - 22.5 33.8 45.0 67.5 90.0 - -M45 4.5 46.0 45.98 46.50 50.85 - 29.5 40.5 63.0 85.5 - - - 33.8 45.0 67.5 90.0 - -

Ameca Thread Inserts Metric

A



Nominal Diameter

Pitch(mm)

DrillBit

Diam (mm)

DrillingDiameter Tap Minimum Drilling Depth

OuterDiameter inFree State

Number of coils in the free state

min. max.Min

OuterDiam

0.5d 0.75d 1d 1.5d 2d 2.5d 3d Min Max 0.5d 0.75d 1d 1.5d 2d 2.5d 3d

M2 0.4 2.1 2.09 2.18 2.52 - - 3.6 4.6 5.6 6.6 7.6 2.5 2.7 - - 3.5 5.9 7.8 10.0 12.0M2.5 0.45 2.6 2.60 2.70 3.08 - - 5.1 6.3 7.6 8.9 10.1 3.3 3.5 - - 3.5 5.9 8.1 10.5 12.9M3 0.5 3.2 3.11 3.22 3.65 - - 5.8 7.3 8.8 10.3 11.8 3.8 4.0 - - 3.9 6.3 8.7 11.1 13.5

M3.5 0.6 3.7 3.63 3.76 4.28 - - 6.9 8.6 10.4 12.2 13.9 4.55 4.75 - - 3.7 6.3 8.7 11.2 13.3M4 0.7 4.2 4.15 4.29 4.91 - - 7.8 9.8 11.8 13.8 15.8 5.15 5.35 - - 3.7 6.1 8.4 10.9 13.2M5 0.8 5.2 5.17 5.33 6.04 - - 9.2 11.7 14.2 16.7 19.2 6.35 6.6 - - 4.3 6.9 9.7 12.3 14.8M6 1.0 6.3 6.22 6.41 7.30 - - 11.2 14.2 17.2 20.2 23.2 7.6 7.85 - - 4.2 6.9 9.6 12.3 14.6M7 1.0 7.3 7.22 7.41 8.30 - - 12.1 15.6 19.1 22.6 26.1 8.65 8.9 - - 5.3 8.2 11.1 14.3 17.4

M8x1 1.0 8.3 8.22 8.41 9.30 - - 13.0 17.0 21.0 25.0 29.0 9.85 10.1 - - 6.1 9.5 12.9 16.5 19.9M8 1.25 8.4 8.27 8.48 9.62 - - 14.2 18.2 22.2 26.2 30.2 9.85 10.1 - - 4.7 7.4 10.6 13.5 16.4M9 1.25 9.4 9.27 9.48 10.62 - - 15.2 19.7 24.2 28.7 33.2 10.85 11.1 - - 5.3 8.6 11.9 15.3 18.1

M10x1 1.0 10.25 10.22 10.41 11.30 - - 15.0 20.0 25.0 30.0 35.0 12.1 12.5 - - 7.6 12.1 16.3 20.7 25.0M10x1.25 1.25 10.4 10.27 10.48 11.62 - - 16.2 21.2 26.2 31.2 36.2 12.1 12.5 - - 6.0 9.7 13.1 16.9 20.1

M10 1.5 10.5 10.32 10.56 11.95 - - 17.3 22.3 27.3 32.3 37.3 12.1 12.5 - - 5.0 8.1 11.2 14.2 17.2M11 1.5 11.5 11.32 11.56 12.95 - - 18.3 23.8 29.3 34.8 40.3 13.1 13.5 - - 5.6 9.0 12.3 15.7 18.9

M12x1 1.0 12.3 12.22 12.41 13.30 - - 17.2 23.2 29.2 35.2 41.2 14.4 14.8 - - 9.3 14.5 19.5 24.8 30.0M12x1.25 1.25 12.4 12.27 12.48 13.62 - - 18.2 24.2 30.2 36.2 42.2 14.4 14.8 - - 7.4 11.6 15.9 20.7 24.8M12x1.5 1.5 12.5 12.32 12.56 13.95 - - 19.3 25.3 31.3 37.3 43.3 14.4 14.8 - - 6.2 9.8 13.5 15.7 20.8

M12 1.75 12.5 12.38 12.64 14.27 - - 20.3 26.3 32.3 38.3 44.3 14.4 14.8 - - 5.2 8.4 11.7 14.7 18.0M14x1.25 1.25 14.4 14.27 14.48 15.62 13.2 16.7 20.2 27.2 34.2 41.2 48.2 17.2 17.7 3.6 6.2 8.4 13.3 18.2 23.1 28.0M14x1.5 1.5 14.5 14.32 14.56 15.95 - 17.7 21.3 28.3 35.3 42.3 49.3 17.2 17.7 - 5.1 7.1 11.2 15.3 19.0 23.2

M14 2.0 14.5 14.43 14.73 16.60 - - 23.3 30.3 37.3 44.3 51.3 17.2 17.7 - - 5.2 8.3 11.5 14.6 17.6M16x1.5 1.5 16.5 16.32 16.56 17.95 - 19.3 23.3 31.3 39.3 47.3 - 19.4 19.9 - 5.9 8.3 13.0 17.7 22.4 -

M16 2.0 16.5 16.43 16.73 18.60 - - 25.3 33.3 41.3 49.3 57.3 19.4 19.9 - - 6.1 9.7 13.3 16.8 19.6M18x1.5 1.5 18.5 18.32 18.56 19.95 16.3 20.8 25.3 34.3 43.3 - - 21.5 22.0 4.2 7.0 9.5 14.9 20.2 - -M18x2 2.0 18.5 18.43 18.73 20.60 18.3 22.8 27.3 36.3 45.3 54.3 62.0 21.5 22.0 3.1 5.1 7.1 11.2 15.1 19.1 23.2M18 2.5 18.75 18.54 18.90 21.25 20.2 24.7 29.2 38.2 47.2 56.2 64.0 21.5 22.0 2.3 3.8 5.6 9.0 12.3 15.5 18.8

M20x1.5 1.5 20.5 20.32 20.56 21.95 17.3 22.3 27.3 37.3 47.3 - - 23.7 24.2 4.9 7.9 10.7 16.7 22.4 - -M20x2 2.0 20.5 20.43 20.73 22.60 19.3 24.3 29.3 39.3 49.3 - - 23.7 24.2 3.5 5.8 8.0 12.5 16.8 - -M20 2.5 20.75 20.54 20.90 23.25 21.2 26.2 31.2 41.2 51.2 61.2 71.2 23.7 24.2 2.7 4.5 6.3 10.0 13.7 17.4 21.0

M22x1.5 1.5 22.5 22.32 22.56 23.95 18.3 23.8 29.3 40.3 51.3 - - 26.3 26.8 5.5 8.6 11.7 18.1 24.5 - -M22x2 2.0 22.5 22.43 22.73 24.60 20.3 25.8 31.3 42.3 53.3 - - 26.3 26.8 3.9 6.4 8.7 13.6 18.4 - -M22 2.5 22.75 22.54 22.90 25.25 22.2 27.7 33.2 44.2 55.2 66.2 - 26.3 26.8 3.0 5.0 6.9 10.9 15.0 18.8 -

M24x1.5 1.5 24.5 24.32 24.56 25.95 19.3 25.3 31.3 43.3 55.3 - - 28.6 29.1 6.0 9.5 12.9 19.8 26.7 - -M24x2 2.0 24.5 24.43 24.73 26.60 21.3 27.3 33.3 45.3 57.3 - - 28.6 29.1 4.3 7.0 9.6 15.0 20.2 - -M24 3.0 24.75 24.65 25.05 27.90 25.1 31.1 37.1 49.1 61.1 73.1 - 28.6 29.1 2.6 4.5 6.2 10.0 14.0 17.5 -

M26x1.5 1.5 26.5 26.32 26.56 27.95 20.3 26.8 33.3 46.3 59.3 - - 31.0 31.5 6.5 10.3 14.0 21.6 29.1 - -M27x1.5 1.5 27.5 27.32 27.56 28.95 20.8 27.6 34.3 47.8 61.3 - - 32.2 32.7 6.7 10.7 14.6 22.6 30.0 - -M27x2 2.0 27.5 27.43 27.73 29.60 22.8 29.6 36.3 49.8 63.3 - - 32.2 32.7 5.1 7.9 10.8 16.8 22.6 - -M27 3.0 27.75 27.65 28.05 30.90 26.6 33.4 40.1 53.6 67.1 - - 32.2 32.7 3.2 5.0 7.1 11.4 15.4 - -

M28x1.5 1.5 28.5 28.32 28.56 29.95 21.3 28.3 35.3 49.3 63.3 - - 33.1 33.6 7.1 11.1 15.2 23.3 31.4 - -M30x1.5 1.5 30.5 30.22 30.56 31.95 22.3 29.8 37.3 52.3 67.3 - - 35.2 35.7 7.8 12.2 16.5 25.3 34.0 - -M30x2 2.0 30.5 30.43 30.73 32.60 24.3 31.8 39.3 54.3 69.3 - - 35.2 35.7 5.7 9.0 12.3 19.0 25.5 - -M30 3.5 31.0 30.76 31.21 34.55 30.3 37.8 45.3 60.3 75.3 - - 35.2 35.7 3.0 4.9 7.0 11.0 14.9 - -

M33x2 2.0 33.5 33.43 33.73 35.60 25.8 34.1 42.3 58.8 75.3 - - 38.3 38.8 6.4 10.1 13.7 21.2 28.4 - -M33 3.5 34.0 33.76 34.21 37.55 31.7 40.0 48.2 64.7 81.2 - - 38.3 38.8 3.4 5.6 7.8 12.2 16.5 - -

M34x1.5 1.5 34.5 34.32 34.56 35.95 24.3 32.8 41.3 58.3 75.3 - - 39.1 39.4 9.2 12.3 19.4 29.0 39.5 - -M36x1.5 1.5 36.5 36.32 36.56 37.95 25.3 34.3 43.3 61.3 49.3 - - 42.1 42.6 8.2 11.2 18.8 26.7 37.8 - -M36x2 2.0 36.5 36.43 36.73 38.60 27.3 36.6 45.3 63.3 81.3 - - 42.1 42.6 6.8 10.3 14.1 21.9 31.1 - -M36x3 3.0 37.0 36.65 37.05 39.90 31.1 40.1 49.1 67.1 85.1 - - 42.1 42.6 4.4 7.2 9.9 15.3 20.5 - -M36 4.0 37.0 36.87 37.34 41.20 34.8 13.8 52.8 70.8 88.8 - - 42.1 42.6 3.2 5.0 7.0 11.1 15.2 - -

M39x3 3.0 40.0 39.65 40.05 42.90 32.6 42.4 52.1 71.6 91.1 - - 45.1 45.6 4.9 7.8 10.8 16.8 22.5 - -M39 4.0 40.0 39.87 40.34 44.20 - 46.1 55.8 75.3 94.8 - - 45.1 45.6 - 5.5 7.7 12.2 16.6 - -

M42x3 3.0 43.0 42.65 43.05 45.90 34.1 44.6 55.1 76.1 97.1 - - 48.5 49.0 5.4 8.5 11.7 18.1 24.0 - -M42 4.5 43.0 42.98 43.50 47.85 - 46.0 57.5 78.5 9935 - - 48.5 49.0 - 5.8 7.3 11.6 15.6 - -

M45x3 3.0 46.0 45.65 46.05 48.90 35.6 46.9 58.1 80.6 103.1 - - 52.00 52.5 5.7 9.1 12.5 19.3 26.2 - -M45 4.5 46.0 45.98 46.50 50.85 - 49.3 60.5 83.0 105.5 - - 53.5 54.0 - 5.6 8.0 12.4 16.8 - -

Ameca Thread Inserts Metric

A.1.1 - 12 -

A


FMP

Ameca Thread Inserts UNC

Nominal Diameter

Pitch(mm)

Drill BitDiam(mm)


min. max.Min

OuterDiam

1d 1.5d 2d 2.5d 3d 1d 1.5d 2d 2.5d 3d

2-56 0.453 2.4 2.30 2.50 2.77 1.7 2.8 3.9 5.0 6.1 2.18 3.28 4.37 5.46 6.55

3-48 0.529 2.7 2.65 2.80 3.20 2.0 3.2 4.5 5.8 7.0 2.51 3.76 5.03 6.30 7.54

4-40 0.635 3.1 3.00 3.15 3.67 2.2 3.6 5.1 6.5 7.9 2.84 4.27 5.69 7.11 8.53

5-40 0.635 3.4 3.33 3.50 4.00 2.5 4.1 5.7 7.3 8.9 3.17 4.75 6.35 7.92 9.52

6-32 0.794 3.8 3.68 3.89 4.54 2.7 4.5 6.2 8.0 9.7 3.50 5.26 7.01 8.76 10.51

8-32 0.794 4.4 4.34 4.52 5.20 3.4 5.5 7.5 9.6 11.7 4.16 6.25 8.33 10.41 12.50

10-24 1.058 5.2 5.06 5.28 6.20 3.8 6.2 8.6 11.0 13.4 4.82 7.24 9.65 12.06 14.48

12-24 1.058 5.8 5.72 5.92 6.86 4.4 7.1 9.9 12.6 15.4 5.48 8.23 10.97 13.71 16.46

1/4-20 1.270 6.7 6.62 6.86 8.00 5.1 8.2 11.4 14.6 17.8 6.35 9.52 12.70 15.87 19.05

5/16-18 1.411 8.4 8.24 8.49 9.77 6.5 10.5 14.5 18.4 22.4 7.92 11.91 15.87 19.83 23.80

3/8-16 1.588 10.0 9.89 10.12 11.59 7.9 12.7 17.5 22.2 27.0 9.52 14.27 19.05 23.80 28.57

7/16-14 1.814 11.6 11.51 11.78 13.47 9.3 14.9 20.4 26.0 31.5 11.11 16.66 22.22 27.78 33.32

1/2-13 1.954 13.2 13.12 13.40 15.24 10.7 17.1 23.4 29.8 36.1 12.70 19.05 25.40 31.75 38.10

9/16-12 2.117 14.9 14.75 15.03 17.04 12.2 19.3 26.5 33.6 40.7 14.27 21.43 28.57 35.71 42.85

5/8-11 2.309 16.5 16.38 16.68 18.88 13.6 21.5 29.4 37.4 45.3 15.87 23.80 31.75 39.67 47.62

3/4-10 2.540 19.8 19.60 19.91 22.35 16.5 26.0 35.5 45.1 54.6 19.05 28.57 38.10 47.62 57.15

7/8-9 2.822 23.0 22.84 23.18 25.89 19.4 30.5 41.6 52.7 63.8 22.22 33.32 44.45 55.55 66.67

1"-8 3.175 26.4 26.09 26.47 29.53 22.2 34.9 47.6 60.3 73.0 25.40 38.10 50.80 63.50 76.20

1" 1/8-7 3.629 29.5 29.36 29.74 33.29 24.9 39.2 53.2 67.8 82.0 28.57 42.85 57.15 71.42 85.72

1" 1/4-7 3.629 32.8 32.54 32.92 36.46 28.1 44 59.9 75.7 91.6 31.75 47.62 63.50 79.37 95.25

1" 3/8-6 4.234 36.2 35.84 36.35 40.42 30.7 48.2 65.7 83.0 100.5 34.92 52.37 69.85 87.30 104.77

1" 1/2-6 4.234 39.5 39.02 39.53 43.62 33.9 52.9 72 91.0 110.0 38.10 57.15 76.20 95.25 114.30

NominalDiameter

Pitch(mm)

DrillBit

Diam(mm)

DrillingDiameter Tap Drilling Depth

OuterDiameter In

The Free StateNumber Of Coils In The Free State

min. max.Min

OuterDiam

1d 1.5d 2d 2.5d 3d min max 1d 1.5d 2d 2.5d 3d

2-56 0.453 2.4 2.30 2.50 2.77 4.2 5.3 6.4 7.5 8.6 2.8 3.0 3.0 5.2 7.4 9.6 11.8

3-48 0.529 2.7 2.65 2.80 3.20 4.9 6.2 7.4 8.7 10.0 3.2 3.5 2.8 5.0 7.2 9.4 11.5

4-40 0.635 3.1 3.00 3.15 3.67 5.7 7.1 8.6 10.0 11.4 3.6 4.0 2.8 4.8 6.8 8.8 10.8

5-40 0.635 3.4 3.33 3.50 4.00 6 7.6 9.2 10.8 12.4 4.0 4.4 3.3 5.5 7.8 10.0 12.2

6-32 0.794 3.8 3.68 3.89 4.54 7.1 8.8 10.6 12.3 14.1 4.5 4.9 2.8 4.8 6.7 8.7 10.8

8-32 0.794 4.4 4.34 4.52 5.20 7.7 9.8 11.9 14.0 16.1 5.2 5.6 3.5 5.9 8.3 10.7 13.2

10-24 1.058 5.2 5.06 5.28 6.20 9.6 12.0 14.4 16.8 19.2 6.2 6.6 2.9 5.0 7.1 9.2 11.4

12-24 1.058 5.8 5.72 5.92 6.86 10.3 13.0 15.7 18.5 21.3 6.8 7.2 3.5 5.9 8.3 10.7 13.2

1/4-20 1.270 6.7 6.62 6.86 8.00 12.1 15.2 18.4 21.6 24.8 8.0 8.4 3.4 5.7 8.0 10.3 12.7

5/16-18 1.411 8.4 8.24 8.49 9.77 14.3 18.3 22.2 26.2 30.2 9.7 10.2 4.0 6.6 9.3 11.9 14.7

3/8-16 1.588 10.0 9.89 10.12 11.59 16.7 21.4 26.2 31.0 35.7 11.5 12.0 4.4 7.2 10.0 12.9 15.7

7/16-14 1.814 11.6 11.51 11.78 13.47 19.3 24.8 30.4 35.9 41.5 13.4 14.0 4.5 7.4 10.3 13.1 16.1

1/2-13 1.954 13.2 13.12 13.40 15.24 21.5 27.8 34.2 40.5 46.9 15.2 15.8 4.8 7.9 10.9 13.9 17.1

9/16-12 2.117 14.9 14.75 15.03 17.04 23.8 31.0 38.1 45.2 52.4 17.0 17.6 5.1 8.3 11.5 14.7 17.8

5/8-11 2.309 16.5 16.38 16.68 18.88 26.3 34.2 42.1 50.1 58.0 18.9 19.5 5.3 8.3 11.8 15.0 18.4

3/4-10 2.540 19.8 19.60 19.91 22.35 30.5 40.0 49.5 59.0 68.6 22.4 23.0 5.9 9.4 13.0 16.5 20.2

7/8-9 2.822 23.0 22.84 23.18 25.89 34.9 46.0 57.2 68.3 79.4 26.0 26.7 6.3 10.0 13.7 17.5 21.3

1"-8 3.175 26.4 26.09 26.47 29.53 39.7 52.4 65.1 77.8 90.5 29.6 30.4 6.4 10.2 14.0 17.7 21.6

1" 1/8-7 3.629 29.5 29.36 29.74 33.29 44.9 59.2 73.5 87.8 102.0 33.4 34.4 6.3 9.9 13.6 17.5 21.3

1" 1/4-7 3.629 32.8 32.54 32.92 36.46 48.1 64.0 79.8 96.0 111.8 36.7 37.7 7.0 11.2 15.4 19.5 23.7

1" 3/8-6 4.234 36.2 35.84 36.35 40.42 54.0 71.4 88.9 106.0 124.0 40.6 41.7 6.5 10.5 14.4 18.4 22.3

1" 1/2-6 4.234 39.5 39.02 39.53 43.62 57.2 76.2 95.3 115.0 133.0 43.9 45.0 7.2 11.5 15.9 20.2 24.5

A



Ameca Thread Inserts UNF

Nominal Diameter

Pitch(mm)

Drill BitDiam(mm)


min. max.Min

OuterDiam

1d 1.5d 2d 2.5d 3d 1d 1.5d 2d 2.5d 3d

2-64 0.396 2.3 2.29 2.44 2.70 1.8 2.9 4.0 5.0 6.2 2.18 3.28 4.37 5.46 6.55

3-56 0.453 2.7 2.62 2.77 3.10 2.0 3.3 4.6 5.8 7.1 2.51 3.76 5.03 6.30 7.54

4-48 0.529 3.0 2.97 3.14 3.53 2.3 3.7 5.2 6.6 8.0 2.84 4.27 5.69 7.11 8.53

6-40 0.635 3.8 3.66 3.81 4.33 2.9 4.6 6.4 8.1 9.9 3.50 5.26 7.01 8.76 10.51

8-36 0.706 4.4 4.32 4.47 5.08 3.4 5.5 7.6 9.7 11.8 4.16 6.25 8.33 10.41 12.50

10-32 0.794 5.1 5.00 5.16 5.86 4.0 6.5 8.9 11.3 13.7 4.82 7.24 9.65 12.06 14.48

1/4-28 0.907 6.7 6.55 6.72 7.53 5.5 8.6 11.8 15.0 18.1 6.35 9.52 12.70 15.87 19.05

5/16-24 1.058 8.3 8.17 8.35 9.31 6.9 10.9 14.9 18.8 22.7 7.92 11.91 15.87 19.83 23.80

3/8-24 1.058 9.9 9.75 9.93 10.90 8.4 13.2 18.0 22.8 27.5 9.52 14.27 19.05 23.80 28.57

7/16-20 1.270 11.5 11.39 11.59 12.76 9.8 15.4 20.9 26.5 32.0 11.11 16.66 22.22 27.78 33.32

1/2-20 1.270 13.1 12.97 13.16 14.35 11.4 17.8 24.1 30.5 36.8 12.70 19.05 25.40 31.75 38.10

9/16-18 1.411 14.7 14.59 14.79 16.12 12.9 20.1 27.2 34.4 41.4 14.27 21.43 28.57 35.71 42.85

5/8-18 1.411 16.3 16.18 16.38 17.71 14.5 22.4 30.4 38.3 46.2 15.87 23.80 31.75 39.67 47.62

3/4-16 1.588 19.5 19.39 19.60 21.11 17.5 27.0 36.5 46.0 55.6 19.05 28.57 38.10 47.62 57.15

7/8-14 1.814 22.7 22.62 22.84 24.58 20.4 31.5 42.7 53.8 64.8 22.22 33.32 44.45 55.55 66.67

1"-14 1.814 26.0 25.86 26.11 27.76 23.6 36.3 49.0 61.7 74.4 25.40 38.10 50.80 63.50 76.20

1"-12 2.117 26.0 25.86 26.11 28.15 23.3 36.0 48.7 61.4 74.0 25.40 38.10 50.80 63.50 76.20

1" 1/8-12 2.117 29.2 29.03 29.29 31.33 26.5 40.7 55.0 69.3 83.6 28.57 42.85 57.15 71.42 85.72

1" 1/4-12 2.117 32.4 32.21 32.21 34.50 29.7 45.5 61.4 77.2 93.1 31.75 47.62 63.50 79.37 95.25

1" 3/8-12 2.117 35.5 35.38 35.38 37.68 32.8 50.3 67.8 85.2 102.6 34.92 52.37 69.85 87.30 104.77

1" 1/2-12 2.117 38.7 38.56 38.56 40.85 36.0 55.1 74.1 93.1 112.2 38.10 57.15 76.20 95.25 114.30

Nominal Diameter

Pitch(mm)

DrillBit

Diam(mm)

DrillingDiameter Tap Drilling Depth

OuterDiameter In

The Free StateNumber Of Coils In The Free State

min. max.Min

OuterDiam

1d 1.5d 2d 2.5d 3d min max 1d 1.5d 2d 2.5d 3d

2-64 0.396 2.3 2.29 2.44 2.70 4.0 5.0 6.2 7.3 8.3 2.79 3.02 3.5 5.6 8.0 10.4 12.5

3-56 0.453 2.7 2.62 2.77 3.10 4.6 5.8 7.1 8.4 9.6 3.3 3.7 3.4 5.6 8.0 10.4 12.6

4-48 0.529 3.0 2.97 3.14 3.53 5.2 6.7 8.1 9.5 10.9 3.7 4.1 3.4 5.6 7.9 10.2 12.5

6-40 0.635 3.8 3.66 3.81 4.33 6.4 8.1 9.9 11.6 13.4 4.5 4.9 3.8 6.0 8.4 10.8 13.2

8-36 0.706 4.4 4.32 4.47 5.08 7.3 9.4 11.5 13.6 15.7 5.3 5.7 4.0 6.6 9.1 11.7 14.2

10-32 0.794 5.1 5.00 5.16 5.86 8.4 10.8 13.2 15.6 18.0 6.1 6.5 4.1 6.8 9.5 12.1 14.9

1/4-28 0.907 6.7 6.55 6.72 7.53 10.4 13.6 16.8 20.0 23.2 7.8 8.3 5.0 8.1 11.3 14.4 17.6

5/16-24 1.058 8.3 8.17 8.35 9.31 12.7 16.7 20.6 24.6 28.6 9.7 10.2 5.5 8.9 12.2 15.6 19.0

3/8-24 1.058 9.9 9.75 9.93 10.90 14.3 19.1 23.8 28.6 33.3 11.4 11.9 6.9 10.9 14.9 19.0 23.2

7/16-20 1.270 11.5 11.39 11.59 12.76 16.8 22.4 27.9 33.5 39.0 13.4 13.9 6.6 10.6 14.5 18.4 22.5

1/2-20 1.270 13.1 12.97 13.16 14.35 18.4 24.8 31.1 37.5 43.8 15.1 15.7 7.8 12.3 16.8 21.3 25.9

9/16-18 1.411 14.7 14.59 14.79 16.12 20.6 27.8 34.9 42.1 49.2 16.9 17.6 7.9 12.5 17.1 21.6 26.2

5/8-18 1.411 16.3 16.18 16.38 17.71 22.2 30.2 38.1 46.0 54.0 18.6 19.3 8.9 14.1 19.1 24.3 29.4

3/4-16 1.588 19.5 19.39 19.60 21.11 26.2 35.7 45.2 54.8 64.3 22.2 22.9 9.7 15.1 20.6 26.0 31.5

7/8-14 1.814 22.7 22.62 22.84 24.58 30.4 41.5 52.6 63.7 74.8 26.0 26.7 9.9 15.4 21.0 26.6 32.2

1"-14 1.814 26.0 25.86 26.11 27.76 33.6 46.3 59.0 71.7 84.4 29.4 30.1 11.5 17.9 24.3 30.6 37.0

1"-12 2.117 26.0 25.86 26.11 28.15 34.9 47.6 60.3 73.0 85.7 29.7 30.4 9.7 15.1 20.6 26.1 31.5

1" 1/8-12 2.117 29.2 29.03 29.29 31.33 38.1 52.4 66.7 81.0 95.3 33.2 33.9 11.1 17.3 23.4 29.6 35.7

1" 1/4-12 2.117 32.4 32.21 32.21 34.50 41.3 57.2 73.0 88.9 104.8 36.6 37.3 12.4 19.3 26.1 33.0 39.8

1" 3/8-12 2.117 35.5 35.38 35.38 37.68 44.5 61.9 79.4 96.8 114.3 40.0 40.9 13.8 21.3 28.9 36.5 44.0

1" 1/2-12 2.117 38.7 38.56 38.56 40.85 47.6 66.7 85.7 104.8 123.8 43.4 44.3 15.2 23.4 31.6 39.8 48.2

A.1.1 - 14 -

A


FMP

Steels For Screws, Bolts and StudsSteels generally used for metric screws, bolts and studs

Property Class Size Materials per DIN 1) Materials per ANSI 1)

3.64.6 to M39

QSt 36-2USt 38-2

UQSt 36-2UQSt 38-2

10061010

4.8 to M16 QSt 36-2QSt 38-2

10061010

5.6 to M39 Cq 22 1022

5.8 to M39 Cq 22Cq 35

10221035

8.8

to M1222B228B2Cq 35

10B2210B28

1035 (1038)

to M22

35B2Cq 35Cq 45

46 Cr 1

10B351035 (1038)

1045

over M24to M39

34 Cr 437 Cr 446 Cr2

51325135

10.9

to M6 35B2Cq 35

10B351035

over M6to M18

34 Cr 441 Cr 4

51325140

to M3941 Cr 4

34 CrMo 442 CrMo 4

513541374140

12.9

to M1834 CrMo4

37 Cr 441 Cr 4

413751355140

to M24 42CrMo 4 4140

to M39 34 CrNiMo 6 4340

1) The above listed materials are generally used. It is however up to the manufacturer’s discretion to use anyother material providing the final product meets the specified chemical composition and mechanical property.

Fuller Metric Parts Ltd. - 1 - B.1.1

B


Stainless SteelDesignation System for Stainless Steel (ISO 3506 1979)

Composition Groups Austenitic Ferritic Martensitic

Identification of Steel Grades A1, A2, A4 F1 C1, C4 C3

PropertyClass

50 70 80 45 60 50 70 80

Soft Cold-Worked

High-Strength Soft Cold-

Worked SoftHardened

andTempered

Hardened and

Tempered

Chemical Composition (Austenitic Group)

Extract from DIN 267 Part 11 - Chemical Composition of austenitic chromium-nickels steels in % by weight

AusteniticGrade

MaterialNo. to AISI C Si Mn P S Cr Mo Ni

A1 303 0.12 1.0 2.0 0.20 0.15 to 0.35 17.0 to 19.0 0.6 8.0 to 10.0

A2 304 0.08 1.0 2.0 0.05 0.03 17.0 to 20.0 - 8.0 to 13.0

A4 316 0.08 1.0 2.0 0.05 0.03 16.0 to 18.5 2.0 to 3.0 10.0 to 14.4

• Maximum values unless otherwise stated.• Types A2 and A4 may contain up to a maximum of 4% copper.• The selection of steel grades within a group is the prerogative of the manufacturer, unless the purchaser has specified particular steels to ISO or

national standards.• Different grades of steel may be used as long as all physical and mechanical properties and the corresponding corrosion resistance of the finished

product are achieved. Only when all these conditions are fulfilled may finished articles be marked in accordance with DIN 267 Part 11.

Mechanical Properties-Austenitic Grades

Bolts, Screws and Studs

Grade PropertyClass

Tensile StrengthRm MPa

(N/mm2) minimum

Yield StressRp 0.2 Mpa

(N/mm2) minimum

Elongation AL

Minimum

Proof Load StressSp Mpa (N/mm2)

minimumDiameter Range

A2andA4

70 700 450 0.4d 700 =<M20

80 800 600 0.3d 800 =<M20

Comparison: US and ISO (DIN) Stainless Steels

Tensile Load

A2 and A4 as compared to 304 and 316 Percent difference from US - Stainless Steel

up to M20 44% higher

M22 and over 6% lower

B.1.1 - 2 -

B


FMP

Selection of Diameters (Tightening Torques, Loads)

Guideline values for screws in steel groups A2-70 and A4-70 with standard metric threads to DIN 13

DiameterLoad1)

Force at 0.2%yield point N

Initial StressingForce

N

TighteningTorque

Nm

Force in service N

AxialStatic

AxialDynamic

RadialStatic or Dynamic

M3 2250 1420 0.9 610 360 120

M4 3960 2490 2.2 1070 640 210

M5 6390 4030 4.3 1730 1040 350

M6 9040 5700 7.3 2440 1470 490

M8 16470 10380 17.7 4450 2670 890

M10 26100 16440 35.5 7050 4230 1410

M12 37930 23900 61.3 10240 6150 2050

M16 70650 44510 147.1 19080 11450 3820

M20 110250 69460 285.1 29770 17860 5950

1)The values correspond to 100% of the 0.2%Notes on application:

• When selecting the correct screw diameter it should be ensured that the total load on the screw does not exceed 90% of thestandardized 0.2% yield stress. Care should be taken to ensure correct initial tensioning, with a torque wrench wherever possible.

• Experience has shown that a utilization of 70% of the total load is reasonable average for the initial stressing force to allow additional forces in service to be taken up.

**The table above is only intended as an aid for quick comparison**

Fuller Metric Parts Ltd. - 3 - B.1.1

B


Comparative International Stainless Steel Grades

British French German Italian Japanese Swedish USA

304S21 Z12CN17.08 1.4310 X12CrNi 17 07 SUS301 14 23 31 301

304S31 SUS302 14 23 32 302

304S15304S16 Z8CN18.09 1.4301 X5CrNi 18 10 SUS301 14 23 33 304

304S11 Z2CN18.10 1.4306 X2CrNi 18 11 SUS304L 14 23 52 304L

305S19 Z8CN18.12 X8CrNi 18 12 SUS305 305

309S24 Z15CN24.13 X16CrNi 23 14 SUS309 309

310S24 Z12CN25.20 1.4845 Z22CrNi 25 20 SUS310S 14 23 61 310

315S16 14 23 40

316S31316S33 Z6CND17.11 1.4401

1.4436 X8CrNiMo 17 13 SUS316 14 23 4314 23 47 316

316S11316S13 Z2CND17.12 1.4404

1.4435 X2CrNiMo 17 12 SUS316L 14 23 5314 23 48 316L

317S12 Z2CND19.15 1.4435 X2CrNiMo 18 16 SUS317L 14 23 67 317L

317S16 1.4436 SUS317 14 23 66 317

320S31320S33 Z8CND17.12 1.4571

1.4573 14 23 50

321S31 Z6CNT18.12 1.4541 X6CrNiTi 18 11 SUS321 14 23 37 321

347S31 Z6CNNb18.11 1.4558 X6CrNiNb 18 11X8CrNiNb 18 11 SUS347 14 23 38 347

403S17 Z6C13 1.4000 X6Cr13 SUS403 14 23 01 403

405S17 Z6CA13 1.4002 Z6CrA1 13 SUS405 405

409S19 1.4512 409

430S17 Z8C17 1.4016 X8Cr 17 SUS430 14 23 20 430

434S17 Z8CD17.01 1.4113 X8CrMo 17 SUS434 14 23 25 434

410S21 Z12C13 1.40061.4024 X12Cr 13 SUS410 13 23 02 410

410S45 Z30C13 X30Cr 13 SUS420JS 14 23 04 420

C.1.1 - 1 -

C

Weight in kgs. per 1,000 pcs. unless otherwise specified. All weights are approximations.All information is strictly informative

FMP

WeightsDIN 931 Hex Head Cap Screw Part Thread

DiameterM4 M5 M6 M7 M8 M10 M12 M14 M16 M18 M20 M22 M24 M30 M36 M48

Length25 3.12 4.86

30 3.61 5.64 8.06 12.7

35 4.04 6.42 9.13 13.6 18.2

40 4.53 7.20 10.2 15.1 20.3 35.0

45 7.98 11.3 16.6 22.2 38.0 53.6

50 8.76 12.3 18.1 24.2 41.1 58.1 82.0

55 13.4 19.5 25.8 43.8 62.6 88.1 115

60 14.4 21.0 27.8 46.9 67.0 94.1 123

65 22.5 29.8 50.0 70.3 98.8 131 171 219

70 24.0 31.8 53.1 74.7 105.0 139 181 231 281

75 33.7 56.2 79.1 111.0 147 191 243 296

80 35.7 59.3 83.6 117.0 155 200 255 311 392

85 62.4 88.1 123.0 163 210 267 326 410

90 65.5 92.4 127.0 171 220 279 341 428 712

95 68.6 96.8 133.0 179 230 291 356 446 739

100 71.7 101.0 139.0 186 240 303 370 464 767

110 109.0 151.0 202 260 327 400 500 823 1240

120 118.0 164.0 218 280 351 430 535 880 1320

130 174.0 230 296 374 450 560 920 1390

140 185.0 246 316 398 480 595 975 1470 2860

150 262 336 422 510 630 1030 1550 3010

160 278 356 446 540 665 1085 1630 3160

170 376 470 570 700 1140 1710 3300

180 396 494 600 735 1200 1790 3440

190 519 630 770 1250 1870 3580

200 544 660 805 1310 1950 3720

220 720 870 1420 2110 4010

240 935 1530 2270 4290

260 1640 2430 4570

280 1750 2590 4850

300 1860 2750 5130

320 5410

340 5690

Fuller Metric Parts Ltd. - 2 - C.1.1

C


DIN 933 Hex Head Cap Screw Full ThreadDiameter

M3 M4 M5 M6 M7 M8 M10 M12 M14 M16 M18 M20 M22 M24 M30 M36 M48Length

4 0.48

5 0.53 1.26

6 0.57 1.33 2.18 3.40

7 0.61 1.41 2.28 3.57 5.60

8 0.66 1.49 2.38 3.74 5.85 8.5 15.2

10 0.75 1.64 2.63 4.08 6.35 9.1 16.2 23.3 38.0

12 0.84 1.80 2.87 4.42 6.85 9.8 17.2 25.0 40.0 52.9

14 0.92 1.95 3.12 4.76 7.35 10.5 18.2 26.4 42.0 55.6

16 1.00 2.10 3.37 5.11 7.85 11.1 19.2 27.7 44.0 58.3 82.0 105 133 173

18 1.09 2.25 3.62 5.45 8.35 11.7 20.2 29.1 46.0 60.9 84.9 110 137 178

20 1.18 2.41 3.87 5.80 8.85 12.3 21.2 31.0 48.0 63.5 87.2 114 143 184

22 1.27 2.56 4.12 6.15 9.35 12.9 22.2 33.0 50.0 66.2 92.2 119 148 190

25 1.40 2.80 4.49 6.65 10.00 13.9 23.7 34.1 53.0 70.2 95.8 124 155 199

28 1.52 3.04 4.86 7.15 10.70 14.9 25.2 36.2 55.9 74.2 100.0 129 161 200

30 1.61 3.19 5.11 7.51 11.30 15.5 26.2 37.7 57.9 76.9 104.0 134 168 214

35 3.57 5.73 8.37 12.50 17.1 28.7 41.3 62.9 83.5 112.0 145 181 229 424 670

40 3.96 6.35 9.23 13.80 18.7 31.2 44.9 67.9 90.2 120.0 155 193 244 448 714 1590

45 4.34 6.99 10.10 15.00 20.3 33.7 48.5 72.9 97.1 128.0 165 206 259 472 748 1650

50 4.73 7.59 11.00 16.30 21.8 36.2 52.0 77.9 103.0 136.0 176 219 274 496 783 1710

55 5.12 8.21 11.90 17.50 23.4 38.7 55.6 82.8 110.0 145.0 186 232 289 519 817 1770

60 5.50 8.83 12.70 18.70 25.0 41.3 58.2 87.8 117.0 153.0 196 244 304 543 851 1830

65 5.89 9.45 13.60 20.00 26.6 43.8 62.8 92.8 123.0 161.0 207 257 319 566 886 1890

70 6.28 10.10 14.40 21.20 28.2 46.3 66.4 97.9 130.0 169.0 217 269 334 590 910 1950

75 10.70 15.30 22.50 29.8 48.8 70.0 102.0 137.0 177.0 227 282 348 614 950 2010

80 11.30 16.20 23.70 31.4 51.3 73.6 107.0 144.0 186.0 238 295 363 637 990 2080

85 25.00 33.0 53.8 77.2 112.0 150.0 194.0 247 308 378 661 1020 2140

90 26.20 34.6 56.3 80.8 117.0 157.0 202.0 258 321 393 685 1060 2200

95 27.50 35.2 59.8 84.4 122.0 164.0 210.0 268 333 408 708 1100 2260

100 28.70 37.7 61.3 88.0 127.0 170.0 218.0 279 346 423 732 1140 2320

110 40.9 66.4 95.2 137.0 184.0 235.0 300 371 453 779 1200 2450

120 71.4 102.0 147.0 197.0 251.0 320 397 483 827 1260 2570

130 76.4 109.0 157.0 210.0 268.0 340 421 513 874 1330 2690

140 81.4 116.0 167.0 224.0 284.0 361 448 543 921 1400 2820

150 86.4 123.0 177.0 237.0 300.0 381 473 572 969 1470 2940

160 316.0 402 498 602 1010 1540 3060

170 332.0 422 523 632 1060 1610 3180

180 348.0 442 548 662 1110 1680 3310

190 364.0 462 573 692 1160 1740 3430

200 380.0 484 598 722 1210 1810 3560

C.1.1 - 3 -

C


FMP

DIN 6914 Hex Head Structural BoltsDiameter

M12 M16 M20 M22 M24 M27 M30 M36Length

30 49.1

35 53.6

40 58.0 105

45 62.1 113 188

50 66.6 121 200 257

55 71.0 129 212 272

60 75.4 137 225 286 362

65 79.9 145 237 301 380

70 84.3 153 249 316 398 532

75 88.8 160 262 331 415 554 701

80 93.2 168 274 346 433 576 728

85 97.6 176 286 361 451 599 756 1184

90 102 184 298 375 467 621 784 1224

95 107 192 310 390 485 644 812 1264

100 199 322 405 503 665 838 1304

105 207 335 420 520 688 865 1336

110 215 347 435 538 710 893 1376

115 223 359 450 556 732 921 1415

120 231 372 465 574 755 949 1455

125 239 384 479 591 777 976 1495

130 247 396 494 609 800 1004 1535

135 409 509 627 822 1032 1575

140 421 524 645 845 1059 1615

145 433 539 662 867 1087 1655

150 446 554 680 890 1115 1695

155 458 569 698 912 1143 1735

160 584 716 935 1170 1775

165 599 733 957 1198 1815

170 751 979 1226 1855

175 769 1002 1254 1895

180 787 1024 1281 1935

185 804 1047 1309 1974

190 822 1069 1337 2014

195 840 1092 1365 2054

200 1114 1392 2094

DIN 906 Hexagon Socket Pipe PlugConical Thread

Size WeightM8x1 2.07

M10x1 3.38M12x1.5 6.10M14x1.5 8.10M16x1.5 11.0M18x1.5 14.6M20x1.5 17.6M22x1.5 22.0M24x1.5 30.8M26x1.5 38.6

M27x2 40.2M30x1.5 M30x2 44

M33x2 57.5M36x1.5 85.2M38x1.5 94.4

M39x2 103M42x1.5 M42x2 135M45x1.5 M45x2 167M48x1.5 M48x2 214M52x1.5 M52x2 253

M56x2 274M60x2 350

DIN 910 Hexagon Socket Pipe PlugCollar Cylindrical Thread

Size WeightM10x1 12.0

M12x1.5 20.3M14x1.5 25.0M16x1.5 35.2M18x1.5 48.6M20x1.5 M20x2 64.5M22x1.5 73.4M24x1.5 93.5M26x1.5 120

M27x2 127M30x1.5 M30x2 148

M33x2 195M36x1.5 M36x2 220M38x1.5 238

M39x2 255M42x1.5 M42x2 300M45x1.5 M45x2 340M48x1.5 M48x2 375M52x1.5 M52x2 430

M56x2 620M60x2 695M64x2 774

DIN 580 Lifting Eye Bolt

Size Weigh in kgper piece

M8 0.06M10 0.11M12 0.18M16 0.28M20 0.45M24 0.74M30 1.66M36 2.65M42 4.03M48 6.38M56 8.80M64 12.4M72 23.3M80 34.2M100 49.1

DIN 582 Lifting Eye Nut

Size Weight in kgper piece

M8 0.05M10 0.09M12 0.16M16 0.24M20 0.36M24 0.72M30 1.32M36 2.08M42 3.11M48 5.02M56 6.69M64 9.30M72 18.5M80 27.3M100 36.4


C


DIN 912 Socket Head Cap ScrewDiameter

M2 M2.5 M3 M4 M5 M6 M8 M10 M12 M14 M16 M18 M20 M22 M24 M30 M36 M48Length

3 0.155

4 0.175 0.345

5 0.195 0.375 0.7

6 0.215 0.405 0.7 1.5

8 0.255 0.465 0.8 1.7 2.5

10 0.295 0.525 0.9 1.8 2.7 4.7

12 0.355 0.585 1.0 2.0 3.0 5.1 10.9

16 0.415 0.705 1.2 2.3 3.5 5.8 12.1 20.9

20 0.495 0.825 1.4 2.7 4.0 6.5 13.4 22.9 32.1

25 0.975 1.6 3.2 4.8 7.6 15.0 25.4 35.7 48 71.3

30 1.9 3.7 5.6 8.3 16.9 27.9 39.3 53 77.8 111 128

35 4.2 6.3 9.9 18.9 30.4 42.9 58 84.4 120 139 211

40 4.7 7.1 11.0 20.9 32.9 46.5 63 91 129 150 224 270

45 7.9 12.1 22.9 36.1 50.1 68 97.6 138 161 237 285 500

50 8.6 13.2 24.9 39.3 54.5 73 106 147 172 250 300 527

55 14.3 26.9 42.5 58.9 78 114 156 183 263 316 554 870

60 15.4 28.9 45.7 63.4 84 122 165 194 276 330 581 910

65 31.0 48.9 67.8 90 130 174 205 291 345 608 950

70 33.0 52.1 71.3 96 138 183 216 306 363 635 990 2040

80 37.0 58.5 80.2 108 154 203 241 336 399 690 1070 2180

90 64.9 89.1 120 170 223 266 366 435 745 1150 2320

100 71.2 98.0 132 186 243 291 396 471 800 1230 2460

110 107.0 144 202 263 316 426 507 855 1310 2600

120 116.0 156 218 283 341 456 543 910 1390 2740

130 168 234 303 366 486 579 965 1470 2880

140 180 250 323 391 516 615 1020 1550 3020

150 266 343 416 546 651 1080 1630 3160

160 282 363 441 576 687 1130 1710 3300

180 403 491 636 759 1240 1870 3590

200 541 696 831 1350 2030 3870

220 756 903 1460 2190 4150

240 975 1570 2250 4430

260 1680 2410 4710

280 1790 2570 4990

300 1900 2730 5270

DIN 913/914/915/916 Set ScrewsDiameter

M1.4 M1.6 M1.8 M2 M2.5 M3 M4 M5 M6 M8 M10 M12 M16 M20 M24Length

2.5 0.018 0.019 0.030

3 0.022 0.028 0.036 0.044 0.075

4 0.029 0.037 0.048 0.059 0.100 0.14

5 0.036 0.046 0.060 0.074 0.125 0.18 0.255 0.42

6 0.043 0.056 0.072 0.089 0.150 0.22 0.38 0.54 0.74

8 0.119 0.199 0.31 0.53 0.78 1.09 1.88

10 0.148 0.249 0.40 0.68 1.02 1.44 2.51

12 0.49 0.83 1.26 1.79 3.14 4.73

16 0.67 1.13 1.74 2.49 4.40 6.73 9.5

20 0.85 1.43 1.22 3.19 5.66 8.71 12.3 20.9

25 2.82 4.07 7.25 11.2 15.9 27.4 41.4

30 4.95 8.84 13.7 19.5 34.0 51.7 70.3

35 5.83 10.40 16.2 23.1 40.5 62.0 85.3

40 12.00 18.7 26.7 47.1 72.3 100

45 82.6 115

50 92.9 130

55 145

60 160

C.1.1 - 5 -

C


FMP

DIN 7991 Flat Head Countersunk Socket CapDiameter

M3 M4 M5 M6 M8 M10 M12 M16 M20 M24Length

8 0.47 0.92 1.60 2.3510 0.56 1.07 1.85 2.70 5.4712 0.65 1.23 2.10 3.05 6.10 10.116 0.83 1.53 2.59 3.76 7.35 12.120 1.00 1.84 3.09 4.46 8.60 14.1 21.225 1.35 2.23 3.71 5.34 10.2 16.6 24.830 1.63 2.9 4.33 6.22 11.7 19.1 28.5 51.835 3.4 5.43 7.10 13.3 21.6 32.1 58.4 91.440 3.9 6.20 8.83 14.8 24.1 35.7 65.1 10250 7.74 11.00 19.9 30.1 43.0 78.4 123 17960 24.8 35.7 54.0 91.7 143 20970 41.2 62.9 111 164 23980 127 200 26990 143 226 299

100 253 340

DIN 434 SquareWasher

Size WeightM8 9.5

M10 8.8M12 18.3M16 31.4M20 57.0M22 82.5M24 128.0M27 119.0

DIN 435 SquareWasher

Size WeightM8 10.1

M10 9.4M12 20.1M16 35.6M20 67M22 90M24 143M27 133

DIN 7989Size Weight

10 15.712 18.816 28.320 43.622 46.224 61.527 7930 10133 11436 140

DIN 6916 Structural Washer

Size WeightM12 7.03M16 14.6M20 19.6M22 24.3M24 30.6M27 50.2M30 63.2M36 115

DIN 6912/DIN 7984 Low Head Socket Head Cap ScrewsDiameter

M4 M5 M6 M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M33 M36Length

10 1.3 2.2 3.6

12 1.5 2.5 3.9 7.7

16 1.9 3.1 4.5 8.8 15.5 22.3

20 2.3 3.7 5.2 10.2 17.9 25.5 37.9 52.5

25 2.7 4.4 6.2 12.5 20.2 29.5 42.5 56.5 77.0

30 3.2 5.1 7.3 14.0 22.0 32.5 48.0 63.0 84.6 108

35 3.4 5.8 8.3 15.7 25.5 36.5 53.0 69.7 93.3 118

40 4.2 6.6 9.5 17.5 28.5 40 58.0 78.7 102 128 185

50 5.2 7.3 11.5 21.5 34.8 48 69.5 91.5 119 150 215

60 9.0 13.6 25.3 40.3 57 82.0 107 138 172 245 263

70 15.7 29.1 46.0 65 92.5 122 157 196 275 298 445 498

80 32.8 52.5 72 104 140 178 222 305 333 490 552 793

90 57.8 80 116 154 196 245 335 369 535 607 860 1000

100 88 127 169 215 269 365 407 580 662 927 1080

110 139 183 235 292 395 439 625 717 994 1160

120 151 198 255 316 425 474 670 772 1060 1240

130 212 275 342 455 510 715 827 1130 1320

140 226 295 368 485 545 760 880 1190 1400

150 315 394 515 580 805 940 1250 1470

160 422 545 616 850 990 1320 1550

170 448 575 651 895 1050 1380 1630

180 474 605 687 940 1100 1450 1710

190 635 722 995 1160 1510 1790

200 665 758 1030 1210 1580 1870


C


DIN 93 Tab WasherSize WeightM3 0.368

M3.5 0.356M4 0.487M5 1.05M6 1.21M7 1.17M8 2.32

M10 3.13M12 6.00M14 7.00M16 8.50M18 11.0M20 11.0M22 14.8M24 14.2M27 31.0M30 36.3M33 42.0M36 51.3M39 59.7M42 69.5M45 81.2M48 89.0M52 98.0

DIN 125 FlatWasher

Size WeightM1.6 0.024M1.7 0.031M2 0.037

M2.3 0.092M2.5 0.088M2.6 0.127M3 0.119

M3.5 0.155M4 0.308M5 0.443M6 1.02M7 1.39M8 1.83

M10 3.57M12 6.27M14 8.62M16 11.3M18 14.7M20 17.2M22 18.3M24 32.3M26 43.7M27 42.3M28 40.9M30 53.6M32 77.4M33 75.3M35 94.3M36 92.1M38 136M39 133M40 130M42 183M45 220M48 294M50 284M52 330M55 431M56 425M58 472M60 458M64 492M68 586M72 626M76 749

DIN 126 FlatWasher

Size WeightM5 0.430M6 0.991M7 1.36M8 1.73

M10 3.44M12 6.07M14 8.38M16 11.0M18 14.0M20 16.4M22 17.5M24 31.1M27 39.5M30 50.5M33 71.0M36 87.4M39 127M42 175M45 212M48 284

DIN 127 LockWasher

Size WeightM2 0.033

M2.2 0.050M2.5 0.053M3 0.11

M3.5 0.12M4 0.18M5 0.36M6 0.83M7 0.93M8 1.60

M10 2.53M12 3.82M14 6.01M16 8.91M18 9.73M20 15.2M22 16.5M24 26.2M27 28.7M30 44.3M36 67.3M39 71.7M42 111M45 117M48 123M52 182M56 193M60 203M64 218M68 228

DIN 432 TabWasher

Size WeightM3 0.33

M3.5 0.32M4 0.44M5 1.20M6 1.48M7 1.42M8 2.54

M10 3.49M12 5.48M14 6.38M16 7.45M18 9.15M20 13.1M22 19.4M24 18.5M27 24.8M30 29.8M33 34.2M36 52.5M39 63.3M42 72.5M45 85.3M48 93

DIN 128Size WeightM2 0.035

M2.5 0.055M3 0.09

M3.5 0.10M4 0.15M5 0.30M6 0.70M7 0.75M8 1.30

M10 2.10M12 3.20M14 4.80M16 7.00M18 7.80M20 12.2M22 13.3M24 21.5M27 23.7M30 42.5M36 68.0

DIN 463 TabWashers

Size WeightM3 0.229

M3.5 0.251M4 0.327M5 0.55M6 0.8M8 1.71

M10 2.51M12 4.41M14 5.09M16 6.3M18 8.24M20 9M22 10M24 12M27 25.3M30 31.4M33 35.6M36 42.5M39 49.7M42 59.2M45 70.3M48 80M52 90.2

DIN 1440 FlatWasher

Size WeightM3 .13M4 .23M5 .36M6 .98M7 1.33M8 2.22M9 3.69

M10 4.56M11 9.25M12 8.99M13 8.36M14 10.8M16 9.68M18 13.8M20 15M22 16.2M23 18.5M25 23.6M26 28.5M28 29.7M30 34.2M32 44.8M33 43.3M35 52.8M36 49.5M40 63.7M45 76.8M50 101

DIN 6796 SpringWasher

Size WeightM2 0.05

M2.5 0.09M3 0.14

M3.5 0.25M4 0.38M5 0.69M6 1.43M7 2.53M8 3.13M10 6.45M12 12.4M14 21.6M16 30.4M18 38.9M20 48.8M22 63.5M24 92.9M27 113M30 170

C.1.1 - 7 -

C


FMP

DIN 6797 Toothed Washer

SizeWeight

Type A Type J1.6 0.0102 0.025 0.040

2.5 0.040 0.0453 0.045 0.045

3.5 0.075 0.0854 0.095 0.105 0.18 0.206 0.22 0.257 0.30 0.358 0.45 0.55

10 0.80 0.912 1.0 1.214 1.6 1.916 2.0 2.418 3.5 3.720 3.8 4.122 5.0 6.024 6.0 6.527 8.0 8.530 9.0 9.5

DIN 6798 Serrated Washer

SizeWeight

Type A/J Type V1.6 0.0202.0 0.030 0.0252.5 0.045 0.0303.0 0.06 0.0403.5 0.11 0.0754 0.14 0.15 0.28 0.26 0.36 0.37 0.508 0.80 0.5

10 1.25 1.012 1.6 1.514 2.3 1.916 2.9 2.318 5.020 6.022 7.524 8.027 1230 14

DIN 7349 FlatWasher

Size Weight3 0.4364 1.245 2.436 4.598 9.15

10 12.712 27.114 39.616 48.518 77.420 73.422 97.124 11627 17430 226

DIN 7980 HighCollar Lock Washer

Size WeightM3 0.105

M3.5 0.114M4 0.195M5 0.370M6 0.425M8 1.05

M10 1.96M12 2.28M14 3.80M16 5.94M18 6.60M20 12.3M22 13.6M24 18.1M27 20.6M30 32M33 35M36 52.5M42 80M48 90

DIN 9021 FenderWasher

Size Weight2.5 0.2803.0 0.3493.5 0.5294 0.7745 1.466 2.797 5.298 6.23

10 12.212 22.214 31.616 40.918 67.420 76.824 13930 27336 522

DIN 137 Spring Washers

SizeWeight

Type A Type BM1 0.006

M1.2 0.009M1.4 0.010M1.7 0.020M1.8 0.020M2 0.028

M2.3 0.035M2.6 0.041M3 0.063 0.166

M3.5 0.088 0.154M4 0.140 0.193M5 0.222 0.266M6 0.247 0.318M7 0.265 0.800M8 0.476 0.76

M10 1.05 2.04M12 3.1M14 5.5M16 6.0M18 7.8M20 8.43M22 11.9M24 14.5M27 21.1M30 29.5

DIN 433 FlatWasher

Size WeightM1 0.010

M1.2 0.013M1.4 0.012M1.6 0.016M1.8 0.023M2 0.047

M2.5 0.055M3 0.080

M3.5 0.110M4 0.140M5 0.385M6 0.79M8 1.52

M10 2.11M12 2.85M14 4.30M16 5.42M18 8.31M20 9.98


C


DIN 439 Jam NutSize WeightM1.6 0.06M1.8 0.08M2 0.11

M2.5 0.22M3 0.29

M3.5 0.37M4 0.57M5 0.83M6 1.60M8 3.20

M10 7.20M12 10.4M14 15.9M16 20.5M18 29.6M20 40.2M22 48.3M24 69.5M27 101M30 139M33 183M36 244M39 316M42 403M45 500M48 617M52 755

DIN 929 Weld NutSize Weight

3 0.784 1.135 1.736 2.507 3.248 5.27

10 9.5812 13.7014 21.3016 28.50

DIN 934 Hex NutSize WeightM1 0.030

M1.2 0.054M1.4 0.063M1.6 0.076M2 0.142

M2.5 0.280M3 0.384

M3.5 0.514M4 0.81M5 1.23M6 2.50M7 3.12M8 5.20

M10 11.6M12 17.3M14 25.0M16 33.3M18 49.4M20 64.4M22 79M24 110M27 165M30 223M33 288M36 393M39 502M42 652M45 800M48 977M52 1220M56 1420M60 1690M64 1980M68 2300M72 2670M76 3040M80 3440M85 3930M90 4930M100 6820

DIN 935 Castle NutSize WeightM4 1.12M5 2.30M6 3.16M7 3.96M8 7.35

M10 15.8M12 20.0M14 27.0M16 38.9M18 57.5M20 75.2M22 93.0M24 131M27 192M30 264M33 333M36 447M39 584M42 710M45 860M48 1060M52 1300

DIN 936 Jam NutSize WeightM8 4.0

M10 8.6M12 12.1M14 18.2M16 20.1M18 29.6M20 36.3M22 43.8M24 58M27 90M30 110M33 155M36 190M39 260M42 307

DIN 985 NylonInsert Lock NutSize WeightM3 0.5M4 1.0M5 1.4M6 2.4M7 3.0M8 5.1

M10 10.6M12 17.2M14 26M16 34M18 45M20 65M22 75M24 100M27 162M30 212M33 317M36 415M39 499M42 628M45 771M48 998

DIN 1587 Acorn NutSize WeightM6 4.66M8 11

M10 20.1M12 28.3M14 57.2M16 54.3M18 95M20 104M22 129M24 216

DIN 6915 Structural Nut

Size WeightM12 23.3M16 44.8M20 73.9M22 104M24 155M27 224M30 300M36 515

DIN 479 Square Head Set ScrewDiameter

M5 M6 M8 M10 M12 M16 M20 M24Length

8 2.59 3.00

10 2.83 3.35 7.2

16 3.57 4.41 9.0 15.5

20 4.05 5.10 10.2 17.4 30.8

25 4.66 5.97 11.7 19.8 34.4

30 5.26 6.84 13.3 22.3 38.0

35 5.87 7.71 14.9 24.8 41.6

40 6.48 8.58 16.4 27.3 45.2 87.6

45 9.44 18.0 29.7 48.8 94.3

50 19.5 32.2 52.4 101 176

55 21.1 34.7 56.0 107 186 259

60 37.2 59.6 114 197 273

70 66.8 127 217 303

80 74.0 140 238 333

90 81.2 153 258 362

100 167 279 392

110 180 299 421

120 193 320 451

140 361 510

C.1.1 - 9 -

C


FMP

DIN 84/85 Slotted Head Machine ScrewDiameter

M1 M1.2 M1.4 M1.6 M2 M2.3 M2.5 M2.6 M3 M3.5 M4 M5 M6 M8 M10Length

2 0.025 0.038 0.053 0.07

3 0.030 0.045 0.062 0.082 0.160 0.240 0.272 0.340 0.471

4 0.035 0.052 0.071 0.094 0.179 0.275 0.302 0.373 0.515 0.728 1.02

5 0.040 0.059 0.080 0.105 0.198 0.290 0.332 0.405 0.560 0.786 1.09

6 0.067 0.089 0.117 0.217 0.316 0.362 0.438 0.604 0.845 1.17 2.06

8 0.106 0.140 0.254 0.368 0.422 0.504 0.692 0.966 1.33 2.20 3.56

10 0.124 0.163 0.291 0.419 0.482 0.570 0.780 1.080 1.47 2.55 3.92 7.85

12 0.186 0.329 0.471 0.542 0.635 0.868 1.200 1.63 2.80 4.27 8.49 14.6

14 0.209 0.365 0.523 0.602 0.700 0.956 1.320 1.79 3.05 4.62 9.13 15.6

16 0.232 0.402 0.575 0.662 0.765 1.040 1.440 1.95 3.30 4.98 9.77 16.6

18 0.440 0.625 0.722 0.831 1.130 1.560 2.10 3.54 5.34 10.40 17.6

20 0.478 0.676 0.782 0.904 1.220 1.680 2.25 3.78 5.69 11.00 18.6

22 0.969 1.310 1.800 2.40 4.02 6.04 11.70 19.6

25 1.070 1.440 1.980 2.64 4.40 6.56 12.60 21.1

28 1.170 1.570 2.160 2.87 4.67 7.10 13.60 22.6

30 1.240 1.660 2.280 3.02 5.02 7.45 14.20 23.6

35 1.880 2.570 3.41 5.62 8.25 15.80 26.1

40 2.100 2.870 3.80 6.25 9.20 17.40 28.6

45 3.170 4.17 6.88 10.00 18.90 31.1

50 3.470 4.57 7.50 10.90 20.60 33.6

55 22.10 36.1

60 38.6

DIN 965 Phillips Flat Head Machine ScrewDiameter

M2.5 M3 M3.5 M4 M5 M6 M8 M10Length

3 0.175

4 0.206 0.290 0.434

5 0.236 0.335 0.494 0.676

6 0.266 0.379 0.554 0.754 1.21

8 0.326 0.467 0.673 0.91 1.45 2.19

10 0.386 0.555 0.792 1.06 1.70 2.54 5.03

12 0.446 0.643 0.911 1.22 1.95 2.89 5.67 9.59

14 0.507 0.731 1.03 1.37 2.19 3.25 6.30 10.6

16 0.567 0.820 1.15 1.53 2.44 3.6 6.94 11.6

18 0.627 0.908 1.27 1.68 2.69 3.95 7.57 12.6

20 0.687 0.996 1.39 1.84 2.94 4.31 8.21 13.6

22 0.747 1.08 1.51 1.99 3.18 4.66 8.84 14.6

25 0.838 1.22 1.69 2.22 3.55 5.19 9.79 16.1

28 1.35 1.87 2.46 3.93 5.72 10.7 17.6

30 1.44 1.99 2.61 4.16 6.08 11.4 18.6

35 2.29 3.00 4.65 6.96 13.0 21.1

40 3.38 5.4 7.84 14.6 23.6

45 6.02 8.73 16.2 26.1

50 6.65 9.61 17.8 28.6

55 19.4 31.1

60 33.7


C


DIN 963 Slotted Flat Head Machine ScrewDiameter

M1.6 M1.8 M2 M2.5 M3 M3.5 M4 M5 M6 M8 M10 M12 M14 M16 M18 M20Length

2 0.046 0.063

3 0.058 0.079 0.100 0.175

4 0.069 0.094 0.119 0.206 0.290 0.434

5 0.081 0.109 0.137 0.236 0.335 0.494 0.676

6 0.093 0.124 0.156 0.266 0.379 0.554 0.754 1.21

8 0.116 0.155 0.193 0.326 0.467 0.673 0.910 1.45 2.19

10 0.139 0.185 0.231 0.386 0.555 0.792 1.06 1.70 2.54 5.03

12 0.216 0.268 0.446 0.643 0.911 1.22 1.95 2.89 5.67 9.59

14 0.246 0.306 0.507 0.731 1.03 1.37 2.19 3.25 6.30 10.6

16 0.277 0.343 0.567 0.820 1.15 1.53 2.44 3.6 6.94 11.6

18 0.381 0.627 0.908 1.27 1.68 2.69 3.95 7.57 12.6

20 0.687 0.996 1.39 1.84 2.94 4.31 8.21 13.6 20.8

22 0.747 1.08 1.51 1.99 3.18 4.66 8.84 14.6 22.2 31.9

25 0.838 1.22 1.69 2.22 3.55 5.19 9.79 16.1 24.4 34.9 47.7

28 1.35 1.87 2.46 3.93 5.72 10.7 17.6 26.6 37.9 51.7 68.0

30 1.44 1.99 2.61 4.16 6.08 11.4 18.6 28.1 39.9 54.4 72.3 90.5

35 2.29 3.00 4.65 6.96 13.0 21.1 31.7 44.9 61.1 80.6 101

40 3.38 5.4 7.84 14.6 23.6 35.3 49.8 67.8 88.9 111

45 6.02 8.73 16.2 26.1 39.0 54.8 74.5 97.2 122

50 6.65 9.61 17.8 28.6 42.6 59.8 81.1 105 132

55 19.4 31.1 46.2 64.7 87.8 114 143

60 33.7 49.8 69.7 94.4 122 153

70 57.1 79.7 108 138 174

80 64.4 89.7 121 155 195

90 134 171 216

100 148 188 237

DIN 964 Slotted Oval Countersunk Machine ScrewDiameter

M1 M1.2 M1.4 M1.6 M2 M2.5 M3 M3.5 M4 M5 M6 M8 M10Length

2 0.016 0.027 0.039 0.055

3 0.021 0.034 0.049 0.067 0.119 0.211

4 0.025 0.041 0.057 0.078 0.138 0.242 0.350 0.536

5 0.029 0.047 0.066 0.09 0.156 0.272 0.395 0.596 0.824

6 0.054 0.076 0.102 0.175 0.302 0.439 0.656 0.902 1.49

8 0.093 0.125 0.212 0.362 0.527 0.775 1.06 1.73 2.66

10 0.111 0.148 0.250 0.422 0.615 0.894 1.21 1.98 3.01 6.14

12 0.287 0.482 0.703 1.01 1.37 2.23 3.36 6.78 11.7

14 0.325 0.543 0.791 1.13 1.52 2.47 3.72 7.41 12.7

16 0.362 0.603 0.880 1.25 1.68 2.72 4.07 8.05 13.7

18 0.4 0.663 0.968 1.37 1.83 2.97 4.42 8.68 14.7

20 0.723 1.06 1.49 1.99 3.22 4.78 9.32 15.7

22 0.783 1.14 1.61 2.14 3.46 5.13 9.95 16.7

25 0.874 1.28 1.79 2.37 3.83 5.66 10.9 18.2

28 1.41 1.97 2.61 4.11 6.19 11.8 19.7

30 1.5 2.09 2.76 4.44 6.55 12.5 20.7

35 2.39 3.15 4.93 7.43 14.1 23.7

40 3.53 5.68 8.31 15.7 25.7

45 6.30 9.20 17.3 28.2

50 6.93 10.10 18.9 30.7

55 20.5 33.2

60 35.8

C.1.1 - 11 -

C


FMP

DIN 7982 Phillips Flat Head Sheet Metal ScrewDiameter

M2.2 M2.9 M3.5 M3.9 M4.2 M4.8 M5.5 M6.3Length

4.5 0.10

6.5 0.14 0.280

9.5 0.20 0.350 0.540 0.66

13 0.27 0.476 0.718 0.88 1.02 1.45

16 0.33 0.584 0.871 1.07 1.23 1.75 2.49 3.07

19 0.692 1.02 1.26 1.44 2.05 2.87 3.61

22 1.17 1.45 1.65 2.35 3.26 4.15

25 1.32 1.64 1.86 2.65 3.65 4.69

32 2.35 3.35 4.56 5.95

38 5.43 7.03

DIN 7983 Phillips Oval Head Sheet Metal ScrewDiameter

M2.2 M2.9 M3.5 M3.9 M4.2 M4.8 M5.5 M6.3Height

4.5 0.14

6.5 0.18 0.332

9.5 0.24 0.440 0.72 0.89

13 0.31 0.566 0.90 1.11 1.32 1.88

16 0.37 0.674 1.05 1.30 1.53 2.18 3.12 4.00

19 0.782 1.20 1.49 1.74 2.48 3.50 4.54

22 1.35 1.68 1.95 2.78 3.89 5.08

25 1.50 1.87 2.16 3.08 4.28 5.62

32 2.65 3.78 5.19 6.88

38 5.97 7.96

DIN 7981 Phillips Pan Head Sheet Metal ScrewDiameter

M2.2 M2.9 M3.5 M3.9 M4.2 M4.8 M5.5 M6.3Length

4.5 0.16

6.5 0.20 0.40

9.5 0.26 0.51 0.79 1.05 1.22 1.85

13 0.33 0.63 0.97 1.27 1.46 2.2 3.2 3.90

16 0.39 0.74 1.12 1.46 1.67 2.5 3.6 4.44

19 0.85 1.27 1.65 1.88 2.8 4.0 4.98

22 1.42 1.84 2.1 3.1 4.38 5.52

25 1.57 2.03 2.3 3.4 4.76 6.06

32 2.8 4.1 5.67 7.32

38 4.7 6.45 8.40


C


DIN 7985 Phillips Pan Head Machine ScrewDiameter


3 0.34

4 0.37 0.621

5 0.40 0.666 0.99 1.40

6 0.43 0.710 1.05 1.48 2.66

8 0.49 0.798 1.17 1.63 2.91

10 0.55 0.876 1.29 1.79 3.16 5.14 10.9

12 0.61 0.954 1.42 1.94 3.41 5.49 11.5 21.2

14 0.67 1.03 1.54 2.10 3.66 5.84 12.2 22.2

16 0.73 1.11 1.67 2.25 3.91 5.29 12.8 23.2

18 0.79 1.19 1.80 2.41 4.16 5.64 13.5 24.2

20 0.85 1.27 1.92 2.56 4.41 6.00 14.2 25.2

22 0.91 1.35 2.05 2.72 4.66 6.35 14.8 26.2

25 1.00 1.47 2.25 2.94 5.03 6.87 15.8 27.7

28 1.09 1.59 2.50 3.24 5.4 7.40 16.8 29.2

30 1.18 1.71 2.63 3.44 5.7 7.75 17.5 30.2

35 3.4 3.94 6.5 8.60 19.1 32.7

40 4.44 7.3 9.50 20.7 35.2

45 8.0 10.4 22.3 37.7

50 8.7 11.3 23.9 41.2

55 25.4 43.7

60 27.0 46.2

DIN 966 Phillips Oval Countersunk Machine ScrewDiameter


3 0.211

4 0.242 0.350 0.536

5 0.272 0.395 0.596 0.824

6 0.302 0.439 0.656 0.902 1.49

8 0.362 0.527 0.775 1.06 1.73 2.66

10 0.422 0.615 0.894 1.21 1.98 3.01 6.14

12 0.482 0.703 1.01 1.37 2.23 3.36 6.78 11.7

14 0.543 0.791 1.13 1.52 2.47 3.72 7.41 12.7

16 0.603 0.880 1.25 1.68 2.72 4.07 8.05 13.7

18 0.663 0.968 1.37 1.83 2.97 4.42 8.68 14.7

20 0.723 1.06 1.49 1.99 3.22 4.78 9.32 15.7

22 0.783 1.14 1.61 2.14 3.46 5.13 9.95 16.7

25 0.874 1.28 1.79 2.37 3.83 5.66 10.9 18.2

28 1.41 1.97 2.61 4.11 6.19 11.8 19.7

30 1.5 2.09 2.76 4.44 6.55 12.5 20.7

35 2.39 3.15 4.93 7.43 14.1 23.7

40 3.53 5.68 8.31 15.7 25.7

45 6.30 9.20 17.3 28.2

50 6.93 10.1 18.9 30.7

55 20.5 33.2

60 35.8

C.1.1 - 13 -

C


FMP

DIN 7 Dowel PinsDiameter

M1 M1.2 M1.5 M2 M2.5 M3 M4 M5 M6 M8 M10 M12 M16 M20Length

23 0.018 0.027 0.044

4 0.025 0.036 0.058 0.105 0.165 0.245

5 0.032 0.045 0.072 0.130 0.204 0.300 0.341 0.879

6 0.038 0.054 0.085 0.155 0.243 0.355 0.640 1.020 1.53

8 0.048 0.072 0.113 0.203 0.320 0.466 0.840 1.330 1.97 3.58

10 0.062 0.090 0.141 0.253 0.397 0.577 1.040 1.640 2.41 4.37 7.01 10.2

12 0.074 0.107 0.168 0.302 0.474 0.688 1.230 1.950 2.85 5.16 8.24 12.0

14 0.125 0.195 0.351 0.550 0.799 1.440 2.260 3.29 5.95 9.47 13.8

16 0.224 0.401 0.627 0.910 1.630 2.570 3.73 6.74 10.70 15.6 28.3

18 0.451 0.705 1.020 1.830 2.880 4.17 7.53 11.90 17.4 31.5

20 0.500 0.782 1.130 2.030 3.190 4.61 8.31 13.20 19.2 34.7 56.4

24 0.937 1.350 2.430 3.800 5.50 9.89 15.60 22.8 41.1 66.2

28 1.570 2.820 4.420 6.40 11.50 18.00 26.4 47.5 76.0

32 1.790 3.210 5.030 7.30 13.00 20.60 30.0 53.9 85.8

36 3.600 5.650 8.19 14.60 23.10 33.6 60.3 95.6

40 4.000 6.270 9.08 16.20 25.50 37.2 66.6 105.0

45 7.030 10.20 18.10 28.60 41.7 74.5 118.0

50 7.800 11.30 20.10 31.70 46.2 82.5 130.0

55 12.40 22.10 34.80 50.7 90.4 142.0

60 13.50 24.00 37.90 55.2 98.4 155.0

70 28.00 44.10 64.1 114.0 179.0

80 32.00 50.30 73.0 130.0 204.0

90 56.50 82.1 146.0 228.0

100 62.70 91.0 161.0 253.0

120 109.0 192.0 302.0

140 224.0 351.0

DIN 1Diameter

M1 M1.5 M2 M2.5 M3 M4 M5 M6 M8 M10 M12 M16Length

8 0.058

10 0.075 0.160

12 0.095 0.206 0.341 0.526

14 0.114 0.240 0.404 0.620 0.88

16 0.135 0.295 0.468 0.712 1.02 1.78

20 0.384 0.605 0.914 1.29 2.23 3.47

30 0.991 1.470 2.04 3.48 5.31 7.76 13.1

40 2.100 2.88 4.84 7.30 10.3 17.8 27.6 39.6 69.8

45 3.35 5.56 8.35 11.7 20.2 31.2 44.6 78.6

50 3.83 6.31 9.45 13.4 22.7 34.9 49.8 87.4

55 7.12 10.60 14.7 25.3 38.8 55.2 96.4

60 7.94 11.80 16.3 27.8 42.5 60.2 105.0

70 14.20 19.7 33.2 50.4 71.8 123.0

80 24.3 38.8 58.5 83.0 143.0

90 28.4 44.5 67.0 94.5 162.0

100 32.6 50.5 75.7 106.0 181.0

120 63.5 94.0 130.0 222.0

140 114.0 157.0 265.0


C


DIN 94 Split PinsDiameter

M1 M1.6 M2 M2.5 M3.2 M4 M5 M6.3 M8 M10 M13Length

6 0.03

8 0.04 0.10

10 0.05 0.12 0.25

12 0.06 0.14 0.28 0.51

14 0.07 0.16 0.31 0.57

16 0.08 0.18 0.34 0.63

18 0.10 0.20 0.37 0.69 1.00

20 0.22 0.40 0.75 1.09 2.16 3.49

22 0.24 0.43 0.81 1.18 2.28 3.74

25 0.27 0.47 0.90 1.31 2.52 4.00

28 0.30 0.51 0.98 1.45 2.76 4.49 8.04

32 0.34 0.56 1.10 1.64 3.07 5.00 8.90

36 0.61 1.22 1.80 3.39 5.49 9.76 15.9

40 0.66 1.34 2.00 3.71 6.00 10.60 17.2

45 1.49 2.17 4.11 6.61 11.70 18.9

50 1.64 2.43 4.51 7.24 12.80 20.6

56 2.70 5.00 8.00 14.00 22.6 38.0 69.5

63 3.02 5.55 8.67 15.60 25.0 41.8 76.0

71 3.38 6.20 9.86 17.30 27.7 46.2 83.4

80 3.78 6.91 11.00 19.20 30.7 51.2 91.8

90 7.71 12.20 21.30 34.1 56.7 101.0

100 8.51 13.50 23.50 37.5 62.2 111.0

112 9.46 15.00 26.10 41.5 66.0 122.0

125 10.50 16.60 28.90 45.9 75.9 134.0

140 32.10 51.0 84.2 148.0

C.1.1 - 15 -

C


FMP

DIN 1481 Spring PinsDiameter

M1 M1.5 M2 M2.5 M3 M3.5 M4 M4.5 M5 M6 M8 M10 M12 M14 M16 M20Length

4 0.015 0.034 0.061 0.095 0.136 0.197 0.239

5 0.019 0.043 0.077 0.118 0.17 0.246 0.299 0.397 0.471

6 0.023 0.051 0.092 0.142 0.204 0.296 0.358 0.476 0.566

8 0.031 0.068 0.122 0.189 0.272 0.394 0.478 0.635 0.754

10 0.038 0.085 0.153 0.236 0.34 0.493 0.597 0.793 0.942 1.38 2.24 3.69 5.55 7.8 9.19 15.3

12 0.045 0.103 0.184 0.283 0.407 0.591 0.716 0.952 1.13 1.66 2.66 4.43 6.66 9.35 11 18.4

14 0.052 0.12 0.214 0.33 0.475 0.689 0.836 1.11 1.32 1.94 3.13 5.17 7.78 10.9 12.9 21.4

16 0.059 0.137 0.244 0.377 0.543 0.788 0.955 1.27 1.51 2.21 3.58 5.9 8.89 12.5 14.7 24.5

18 0.067 0.154 0.275 0.424 0.611 0.886 1.07 1.43 1.70 2.49 4.03 6.64 10 14 16.5 27.5

20 0.076 0.171 0.305 0.471 0.679 0.985 1.19 1.59 1.88 2.77 4.48 7.38 11.1 15.6 18.4 30.6

22 0.336 0.519 0.746 1.08 1.31 1.75 2.07 3.04 4.92 8.12 12.2 17.1 20.2 33.6

24 0.367 0.565 0.814 1.18 1.43 1.9 2.26 3.32 5.37 8.86 13.3 18.7 22 36.7

26 0.397 0.613 0.882 1.28 1.55 2.06 2.45 3.6 5.82 9.59 14.4 20.3 23.9 39.8

28 0.427 0.66 0.95 1.38 1.67 2.22 2.64 3.87 6.26 10.3 15.6 21.8 25.7 42.8

30 0.458 0.707 1.02 1.48 1.79 2.38 2.83 4.15 6.71 11.1 16.7 23.4 27.6 45.9

32 1.09 1.58 1.91 2.54 3.02 4.43 7.16 11.8 17.8 24.9 29.4 48.9

36 1.22 1.77 2.18 2.86 3.39 4.98 8.06 13.3 20 28.1 33.1 55.1

40 1.36 1.97 2.39 3.17 3.77 5.54 8.95 14.8 22.2 31.2 36.7 61.2

45 2.68 3.57 4.24 6.23 10.1 16.6 25 35.1 41.3 68.8

50 2.98 3.96 4.71 6.92 11.2 18.4 27.8 39 45.9 76.5

55 5.18 7.61 12.3 20.3 30.5 42.9 50.5 84.1

60 5.65 8.3 13.4 22.1 33.3 46.8 55.1 91.8

65 6.12 8.99 14.5 24 36.1 50.1 59.7 99.4

70 6.59 9.69 15.7 25.8 38.9 54.6 64.3 107

75 7.06 10.4 16.8 27.7 41.7 58.5 68.9 115

80 7.54 11.1 18.0 29.5 44.4 62.4 73.5 122

85 11.8 19.0 31.4 47.2 66.3 78.1 130

90 12.5 20.1 33.2 50 70.2 82.7 138

95 13.1 21.3 35 52.8 74.1 87.3 145

100 13.8 22.4 36.9 55.5 77.9 91.9 153

120 26.8 44.3 66.6 93.5 110 184

140 51.7 77.8 109 129 214

160 59 88.9 125 147 245

180 100 140 165 275


C


DIN 6325 Dowel PinsDiameter

M0.8 M1 M1.5 M2 M2.5 M3 M4 M5 M6 M8 M10 M12 M14 M16 M20Length

2 0.008

3 0.012

4 0.016 0.025 0.055

5 0.020 0.032 0.069

6 0.024 0.038 0.083 0.148 0.230

8 0.032 0.048 0.111 0.197 0.307 0.443

10 0.062 0.139 0.246 0.384 0.554 0.985

12 0.074 0.166 0.296 0.462 0.665 1.18 1.85

14 0.194 0.345 0.538 0.775 1.38 2.16 3.10

16 0.222 0.395 0.615 0.886 1.58 2.46 3.55

18 0.444 0.692 0.996 1.77 2.77 3.99 7.10

20 0.493 0.769 1.11 1.97 3.08 4.44 7.89

24 0.924 1.33 2.37 3.7 5.32 9.46 14.8

28 1.55 2.76 4.32 6.21 11.0 17.2 24.9

32 1.77 3.15 4.93 7.10 12.6 19.7 28.4

36 3.55 5.54 7.98 14.2 22.2 31.7 43.5

40 3.94 6.15 8.86 15.8 24.6 35.5 48.3 63.1

45 6.93 9.96 17.7 27.7 40.0 54.4 71.0

50 7.7 11.1 19.7 30.8 44.4 60.4 78.9 123

55 12.2 21.6 33.9 48.8 66.4 86.8 136

60 13.3 23.6 37.0 53.3 72.5 94.6 148

70 27.6 43.2 62.2 84.6 110 173

80 31.5 49.4 71.0 96.6 126 197

90 55.5 79.9 109 142 222

100 61.6 88.8 121 158 246

120 145 189 296

C.1.1 - 17 -

C


FMP

DIN 471 ExternalRetaining Ring

Diameter Weight65 18.2068 21.8070 22.0072 22.5075 24.6078 26.2080 27.3082 31.2085 36.4088 41.2090 44.5095 49.00

100 53.70105 80110 82115 84120 86125 90130 100135 104140 110145 115150 120155 135160 150165 160170 170175 180180 190185 200190 210195 220200 230210 248220 265230 290240 310250 335260 355270 375280 398290 418300 440

DIN 471 ExternalRetaining Ring

Diameter Weight3 0.0174 0.0225 0.0666 0.0847 0.1218 0.1589 0.30

10 0.3411 0.4112 0.5013 0.5314 0.6415 0.6716 0.7017 0.8218 1.1119 1.2220 1.3021 1.4222 1.5024 1.7725 1.9026 1.9628 2.9229 3.2030 3.3132 3.5434 3.8035 4.0036 5.0038 5.6240 6.0342 6.5045 7.5048 7.9050 10.252 11.155 11.456 11.858 12.660 12.962 14.363 15.9

DIN 472 InternalRetaining Ring

Diameter Weight8 0.149 0.15

10 0.1811 0.3112 0.3713 0.4214 0.5215 0.5616 0.617 0.6518 0.7419 0.8320 0.921 122 1.124 1.4225 1.526 1.628 1.830 2.0631 2.132 2.2134 3.235 3.5436 3.737 3.7438 3.940 4.742 5.445 647 6.148 6.750 7.352 8.255 8.356 8.758 10.560 11.162 11.263 11.765 14.368 1670 16.572 18.1

DIN 472 InternalRetaining Ring

Diameter Weight75 18.878 20.480 2282 2485 25.388 2890 3192 3295 3598 37

100 38102 55105 56108 60110 64.5112 72115 74.5120 77125 79130 82135 84140 87.5145 93150 105155 107160 110165 125170 140175 150180 165185 170190 175195 183200 195210 270220 315230 330240 345250 360260 375270 388280 400290 415300 435

DIN 6799 CirclipSize Weight0.8 0.0031.2 0.0091.5 0.0211.9 0.0402.3 0.0693.2 0.0884 0.1585 0.2366 0.2557 0.4748 0.669 1.09

10 1.2512 1.6315 3.3719 6.4224 8.5530 13.5

DIN 6880 Key Stock

Size Weightkg/m

2x2 0.03143x3 0.07074x4 0.1265x5 0.1966x6 0.2837x7 0.3858x8 0.503

10x10 0.78512x12 1.1314x14 1.5416x16 2.0118x18 2.5420x20 3.1422x22 3.8

8x7 0.4410x8 0.62812x8 0.754

12x10 0.94314x9 0.989

16x10 1.2618x11 1.5520x12 1.8822x14 2.4225x14 2.7525x22 4.3228x16 3.5228x25 5.532x18 4.5232x30 7.5436x20 5.6536x34 9.6140x22 6.9140x38 11.945x25 8.8345x43 15.250x28 1150x48 18.856x32 14.163x32 15.870x36 19.880x40 25.190x45 31.8

100x50 39.35x3 0.1186x4 0.1887x4 0.228x5 0.314

10x6 0.47112x6 0.56514x6 0.65916x7 0.87918x7 0.98920x8 1.2622x9 1.5525x9 1.77

28x10 2.232x11 2.7636x12 3.3940x14 4.4


C


DIN 939 StudDiameter

M5 M6 M8 M10 M12 M16 M20 M24 M27Length

22 3.65

25 4.11 5.85

28 4.57 6.52

30 4.88 6.96 13.1

35 5.65 8.07 15.1 24.2

40 6.42 9.18 17 27.2 41

45 7.19 10.2 19 30.3 45.4

50 7.96 11.4 21 33.3 49.9 94.9

55 12.5 22.9 36.4 54.3 103

60 13.6 24.9 39.5 58.8 111 180

65 26.9 42.6 63.2 119 192

70 28.9 45.7 67.6 126 205 305

75 30.8 48.8 72.1 134 217 323 430

80 32.8 51.8 76.5 142 229 341 452

85 54.9 81 150 241 358 475

90 58 85.4 158 254 376 497

95 61.1 89.8 166 266 394 520

100 64.2 94.3 174 279 412 542

110 103 190 303 447 587

120 112 205 328 483 632

130 221 353 518 677

140 237 377 554 722

150 253 402 589 767

160 269 427 625 812

170 451 660 857

180 476 696 902

190 501 731 947

200 525 767 992

220 1082

240 1172

Steel Round Bar

Diameter Weight kg.per/m

M1 0.0062M2 0.0247M3 0.0555M4 0.0987M5 0.1540M6 0.2220M7 0.3020M8 0.3950M9 0.4990

M10 0.6170M11 0.7460M12 0.8880M13 1.04M14 1.21M15 1.36M16 1.58M17 1.78M18 2.00M19 2.23M20 2.47M21 2.72M22 2.98M23 3.26M24 3.55M25 3.85M26 4.17M27 4.50M28 4.83M29 5.19M30 5.55M32 6.31M33 6.71M34 7.13M35 7.55M36 7.99M38 8.90M40 9.87M41 10.40M42 10.90M43 11.40M44 11.90M45 12.50M46 13.00M48 14.20M50 15.40M55 18.70M60 22.20M65 26.00M70 30.20M75 34.70M80 39.50M85 44.50M90 49.50M95 55.60M100 61.70

DIN 975 ThreadedRod

Size WeightM2 18.7

M2.5 30.0M3 44.0

M3.5 60.0M4 78.0M5 124M6 177M8 319

M10 500M12 725M14 970M16 1330M18 1650M20 2080M22 2540M24 3000M27 3850M30 4750M33 5900M36 6900M39 8200M42 9400M45 11000M48 12400

information

Documents

thread din

flat washer din

structural washer din

square washer din

spring lock washer din

long tab washer din

external tab washer

split lock washer din