infinity kheops bracelet akke · 2015. 10. 20. · infinity bracelet...
TRANSCRIPT
INFINITY BRACELET Designed by Akke Jonkhof
AKKESIERADEN
© 2015 all rights are reserved
Distributed by the Beadsmith. This product may be distributed and taught by customers of the Beadsmith. This document may not be altred in any way or form without the approval of Akke Jonkhof
[email protected]/www.akkesieraden.nl
You need:
Kheops™ par Puca (A)
Infinity beads (B)
seed beads size 11/0 (C)
seed beads size 11/0 (D)
The bar of a toggle clasp circa 20 mm
#12 beading needle
KO thread
Length of the bracelet without the clasp: 20 cm/ Approx. 8 inches
1)Pick up 1A, 1B and pass back through the second hole of the B. Pick up 1B and pass back through the second hole of the B and pass through the second hole of the A.
2) Pass through the first hole of the A and B for a second time.
3) Pick up 1A and pass back through the second hole of the A.
4) Pick up 1B and pass back through the second hole. Pass also through the top hole of the B you added in the previous step, pass back through the lower hole, and pass a second time through the A you added in the
previous step.
5) Repeat step 2, 3 and 4 five more times
6) Pick up 1A and pass back through the second hole. Pass through the lower hole of the B you picked up in step 1 and pass back through the top hole. Pass through the top hole of the next B and pass back through the lower hole. Pass through the A with which you started this step.
7) Pass back through the second hole of the A, pass through the next B and pass back through the second hole. Pick up 1 C and pass through the top hole of next B.
8) Add C beads between all top holes of the B beads. Pass through the first B you passed in step 7 and again through the first C you added.
9) Pick up 2D
and pass through the lower hole of the next B. Pick up 2D and pass through the next C.
10) Repeat step 9 till you added D beads between all C and the lower holes of the B beads.
You finished your first rosette! Make 6 more rosettes.
11) To connect the rosettes: Make sure your needle is coming from an A.
Pick up 1B and pass through an A of another rosette. Pass through the next B and pass back through the second hole. Pass through the next C, and B and pass back through the second hole. Pass back through the second hole of the A and pass through the second hole of the B you picked up. Pass through the second hole of the A you started this step from. Pass through the next B and pass back through the second hole. Pass through the next C and B and pass back through the second hole. Finally pass through the first hole of the A you started the step from. Pass two or three more times through all beads to make the connection tight.
If you have assembled the 7 rosettes, you can add the clasp.
For the clasp you use only the bar of the toggle clasp. Make sure your needle is exciting the A bead where your bar should come. Pick up 7D, the toggle bar, 1D and pass back through the 6th, 5th, 4th , and 3th D you added in this step. Pick up 2D and pass through the other hole of the A you started this step from. Follow the thread path as descript in step 11 to come to the point you started this step from. Pass through all beads two or three more times to make the connection tight. Use the last rosette as the ring of your toggle clasp.
http://www.akkesieraden.etsy.com
Distributed by the Beadsmith. This product may be distributed and taught by customers of the Beadsmith. This document may not be altred in any way or form without the approval of Akke Jonkhof
[email protected]/www.akkesieraden.nl