inchworm - amazon s3 · inchworm by monty kim 1 build your circuit. press the servo hub onto the...

12
INCHWORM BY MONTY KIM BUILD YOUR CIRCUIT. 1 PRESS THE SERVO HUB ONTO THE SERVO. You can secure the hub with the included small screw found with the servo accessories. 2 p4 POWER i16 PULSE o11 SERVO

Upload: others

Post on 24-Jun-2020

2 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

INCHWORMBY MONTY KIM

BUILD YOUR CIRCUIT.1

PRESS THE SERVO HUB ONTO THE SERVO. You can secure the hub with the included small screw found with the servo accessories.2

p4 POWER

i16 PULSE

o11 SERVO

Page 2: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

ATTACH YOUR CIRCUIT TO THE INCHWORM TEMPLATE.3

ATTACH THE BATTERY TO THE TEMPLATE. Use Glue Dots.4

INCHWORM

Page 3: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

ATTACH THE SERVO TO THE TEMPLATE WHERE INDICATED. Use Glue Dots.5

GIVE YOUR INCHWORM SOME MUSCLES. Use a twist tie.6

INCHWORM

Page 4: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

FEED THE TWIST TIE THROUGH THE SERVO HUB. 7

THREAD THE FREE ENDS OF THE TWIST TIE THROUGH THE TWO SMALL HOLES ON THE INCHWORM TEMPLATE.8

INCHWORM

Page 5: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

FOLD THE TEMPLATE, AND TWIST THE TWIST TIE.9

TWIST THE TIES 2 OR 3 TIMES. This will keep the template in an “A” shape.10

INCHWORM

Page 6: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

POWER ON YOUR CIRCUIT.

START INCHING. Adjust the slider on the pulse Bit to change your Inchworm’s speed.

11

12

POWER:ON

INCHWORM

Page 7: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

MOVING COLLAGEBY MONTY KIM

BUILD YOUR CIRCUIT.1

PRESS THE SERVO HUB ONTO THE SERVO.2

p4 POWER

i6 DIMMER

o11 SERVO

Page 8: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

PRESS THE SERVO INTO THE SERVO MOUNT FROM THE SIDE AND SCREW IN.3

CONNECT THE MECHANICAL ARM TO THE SERVO HUB.4

JUST ONE SCREW NEEDED

USE PHILLIPS-HEADSCREWDRIVER

USE PHILLIPS-HEADSCREWDRIVER

MOVING COLLAGE

Page 9: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

PRESS ADHESIVE SHOES ONTO YOUR CIRCUIT.5

SET SERVO TO SWING MODE. 6

MODE:SWING

MOVING COLLAGE

Page 10: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

TEST YOUR CIRCUIT. Turn the power on and twist the dimmer knob. The servo arm should swing back and forth.7

MAKE THE STORY OF YOUR MOVING COLLAGE. You will need two images. Cut out a background image and a moving image.8

USE SCISSORS

POWER:

TWIST

ON

MOVING COLLAGE

Page 11: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

ATTACH THE MOVING IMAGE TO THE MECHANICAL ARM.9

MOUNT YOUR BACKGROUND IMAGE TO THE WALL AND TAPE ALL FOUR CORNERS DOWN WELL. 10

USE TAPE

USE TAPE

MOVING COLLAGE

Page 12: INCHWORM - Amazon S3 · INCHWORM BY MONTY KIM 1 BUILD YOUR CIRCUIT. PRESS THE SERVO HUB ONTO THE SERVO. 2 You can secure the hub with the included small screw found with the servo

PEEL THE BACK OFF THE ADHESIVE SHOES AND STICK YOUR CIRCUIT TO THE COLLAGE.

SET IT IN MOTION! Twist the dimmer to make the animated element move faster or slower across the background.

11

12

SECURE YOURBATTERY TO THEWALL

USE TAPE

ADJUST THE POSITION OFTHE MECHANICAL ARM SOTHAT IT SWINGS WHEREYOU WANT IT TO.

POWER:ON

MOVING COLLAGE