hwmnbtsemodules

GERAN

Hardware

Base Transceiver Station Equipment

HWMN:BTSE Modules

A50016-G5100-A083-01-7620

2 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f1647

f Important Notice on Product Safety

DANGER - RISK OF ELECTRICAL SHOCK OR DEATH - FOLLOW ALL INSTALLATION INSTRUCTIONS.

The system complies with the standard EN 60950 / IEC 60950. All equipment connected to the system must comply with the applicable safety standards.Hazardous voltages are present at the AC power supply lines in this electrical equipment. Some components may also have high operating temperatures.Failure to observe and follow all installation and safety instructions can result in serious personal injury or property damage.Therefore, only trained and qualified personnel may install and maintain the system.

The same text in German:

Wichtiger Hinweis zur Produktsicherheit

LEBENSGEFAHR - BEACHTEN SIE ALLE INSTALLATIONSHINWEISE.

Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Alle an das System angeschlossenen Gerte mssen die zutreffenden Sicherheitsbestimmungen erfllen.In diesen Anlagen stehen die Netzversorgungsleitungen unter gefhrlicher Spannung. Einige Komponenten knnen auch eine hohe Betriebstemperatur aufweisen.Nichtbeachtung der Installations- und Sicherheitshinweise kann zu schweren Krperverletzungen oder Sachschden fhren.Deshalb darf nur geschultes und qualifiziertes Personal das System installieren und warten.

Caution:

This equipment has been tested and found to comply with EN 301489. Its class of conformity is defined in table A30808-X3247-X910-*-7618, which is shipped with each product. This class also corresponds to the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor-dance with the relevant standards referenced in the manual Guide to Documentation, may cause harmful inter-ference to radio communications.For system installations it is strictly required to choose all installation sites according to national and local require-ments concerning construction rules and static load capacities of buildings and roofs.For all sites, in particular in residential areas it is mandatory to observe all respectively applicable electromagnetic field / force (EMF) limits. Otherwise harmful personal interference is possible.

Trademarks:

All designations used in this document can be trademarks, the use of which by third parties for their own purposes could violate the rights of their owners.

Copyright (C) Siemens AG 2006

Issued by the Communications GroupHofmannstrae 51D-81359 Mnchen

Technical modifications possible.Technical specifications and features are binding only insofar as they are specifically and expressly agreed upon in a written contract.

Copyright (C) Siemens AG 2006

Issued by the Communications GroupHofmannstrae 51D-81359 Mnchen

Technical modifications possible.Technical specifications and features are binding only insofar as they are specifically and expressly agreed upon in a written contract.

A50016-G5100-A083-01-7620

3

HWMN:BTSE Modules

Id:0900d805800f1647

Table of ContentsThis document has 209 pages.

Reason for Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151.1 Purpose of the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151.2 Structure of the Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151.3 Rack Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.4 General Information on BTSE LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.5 Removing and Inserting Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2 Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.1 A:COOLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202.2 A:DUAMCO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.3 A:DUXMEG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252.4 A:OVP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262.5 A:TIFNTPM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.6 ABISCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312.6.1 M:ABISCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322.6.2 M:ABISCONCX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322.7 AC/DC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332.7.1 AC/DCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342.7.2 AC/DCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362.7.3 AC/DCM-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372.7.4 AC/DC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382.7.5 ACPSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402.7.6 ACPSC/U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442.7.7 DCPSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442.8 ACPROTECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452.8.1 ACPROTECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462.8.2 ACPROTECT-2M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472.9 ACT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482.9.1 ACTA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492.9.2 ACTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502.9.2.1 ACTC12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502.9.2.2 ACTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512.9.2.3 ACTC-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522.9.2.4 M:ACTC-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532.9.3 ACTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542.9.4 ACTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552.10 AGENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582.11 AGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632.11.1 M:AGINV1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632.11.2 M:AGINV2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642.11.3 M:AGINV3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652.12 BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662.12.1 BCOMPG/BCOMD/BCOMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

4 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f1647

2.12.2 BCOM12PGV/BCOM12DV/BCOM12PV . . . . . . . . . . . . . . . . . . . . . . . . . . . 702.13 CCINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742.14 COAMCO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 772.15 COBA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 802.15.1 M:COBA2P8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 812.15.2 M:COBA4P12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872.15.3 M:COBAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 912.16 COREXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972.17 COSA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 982.17.1 M:COSA6P16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 982.17.2 M:COSA4P12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1022.18 CU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1062.19 DCBCTRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1102.19.1 DCBCTRLA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1112.19.2 DCBCTRLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1132.19.3 DCBCTRLM-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1162.19.4 DCBCTRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1182.19.4.1 DCBCTRLV1V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1182.19.4.2 DCBCTRLV3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1212.20 DCM-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1242.21 DCREFE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1252.22 DCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1272.23 DIAMCO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1312.23.1 DIAMCO V3V5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1332.23.2 DIAMCO V6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1352.24 DIPLEXER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1372.25 DPSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1382.26 DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1392.26.1 DUAMCO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1432.26.2 DUAMCO4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1442.26.3 DUAMCO8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1452.27 DUBIAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1462.28 DUSTFILM-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1472.29 ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1482.30 FAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1522.30.1 FANM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1532.30.2 FAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1532.31 FDUAMCO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1542.32 FICOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1592.32.1 FIPLUB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1592.32.2 FIPLUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1622.33 FlexCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1662.34 FWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1702.35 GCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1712.36 HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1752.36.1 HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1762.36.2 HEATER-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177

A50016-G5100-A083-01-7620

5

HWMN:BTSE Modules

Id:0900d805800f1647

2.36.3 HEATER-2DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1782.36.4 HEATER48/120/220/AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1782.36.5 HEATERM-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1782.37 HEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1792.38 HPDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1802.39 MEF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1822.39.1 MEF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1822.39.2 MEF150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1832.39.3 MEFM-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1842.40 OPEXAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1852.41 OVPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1872.41.1 M:OVPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1882.41.2 M:OVPTKOAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1902.41.3 M:OVPTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1922.41.4 M:OVPTCOAXM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1952.42 TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1972.42.1 TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1982.42.2 STMA/DTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2002.43 TMB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205

6 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f1647

List of FiguresFigure 1 Module Fastening Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Figure 2 Location of the Plug-in Module Code Keys. . . . . . . . . . . . . . . . . . . . . . . 18Figure 3 Location of the Plug-in Module Code Key Number. . . . . . . . . . . . . . . . . 18Figure 4 A:COOLING: Configuration with 2 NTPMs and the A:DUAMCO . . . . . . 20Figure 5 A:DUAMCO: 4:1 and 2:1 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Figure 6 A:DUAMCO: DIP Switch (Factory Setting) . . . . . . . . . . . . . . . . . . . . . . . 23Figure 7 A:DUXMEG: Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Figure 8 A:OVP: Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Figure 9 A:TIFNTPM: Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Figure 10 A:TIFNTPM: Mechanical Sketch Top View. . . . . . . . . . . . . . . . . . . . . . . 28Figure 11 A:TIFNTPM: Configuration with 2 NTPMs and the A:DUAMCO. . . . . . . 30Figure 12 ABISCON: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Figure 13 AC/DCA: Appearance and LED Indications . . . . . . . . . . . . . . . . . . . . . . 34Figure 14 AC/DCD: Appearance and LED Indications . . . . . . . . . . . . . . . . . . . . . . 36Figure 15 AC/DCM-2: Appearance and LED Indications . . . . . . . . . . . . . . . . . . . . 37Figure 16 AC/DC: Appearance and LED Indications . . . . . . . . . . . . . . . . . . . . . . . 38Figure 17 ACPSC/DCPSC: Appearance and LED Indications . . . . . . . . . . . . . . . . 40Figure 18 ACPSC: Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Figure 19 DCPSC: Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Figure 20 ACPROTECT: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Figure 21 ACPROTECT-2M: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Figure 22 ACT: Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Figure 23 ACTA: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Figure 24 ACTA: Connector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Figure 25 ACTC12: Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Figure 26 ACTC12: Connector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Figure 27 ACTC: Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Figure 28 ACTC: Connector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Figure 29 ACTC-3: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Figure 30 M:ACTC-4V1: Appearance (Front View). . . . . . . . . . . . . . . . . . . . . . . . . 53Figure 31 M:ACTC-4V1: Switch Locations (Top View) . . . . . . . . . . . . . . . . . . . . . . 53Figure 32 ACTM: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Figure 33 ACTP: Connector Locations (Horizontal DIP Switch Variant). . . . . . . . . 55Figure 34 ACTP: Connector Locations (Vertical DIP Switch Variant) . . . . . . . . . . . 56Figure 35 ACTP: DIP Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Figure 36 AGENT: with Indoor Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Figure 37 AGENT: with Outdoor Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Figure 38 AGENT: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Figure 39 LIPA: Appearance and Connector Locations . . . . . . . . . . . . . . . . . . . . . 60Figure 40 AGENT: Antenna Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Figure 41 AGENT: Antenna Connection with Internal Patch Antenna . . . . . . . . . . 61Figure 42 AGENT: Antenna Connection with Duplexer . . . . . . . . . . . . . . . . . . . . . 62Figure 43 AGINV1: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Figure 44 AGINV2: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Figure 45 AGINV3: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

A50016-G5100-A083-01-7620

7

HWMN:BTSE Modules

Id:0900d805800f1647

Figure 46 BCOMPG: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Figure 47 BCOMP: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Figure 48 BCOM12: Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Figure 49 BCOM12: Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Figure 50 CCINT: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Figure 51 COAMCO: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . . . 78Figure 52 COBA2P8: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . . . 81Figure 53 COBA2P8: DIP Switch Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Figure 54 COBA2P8: DIP Switch Settings of Port 1 and Port 2. . . . . . . . . . . . . . . 85Figure 55 COBA2P8: DIP Switch Settings of External Clock Synchronization . . . 86Figure 56 COBA4P12: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . . 87Figure 57 COBA4P12: DIP Switch Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Figure 58 COBA4P12_Switch_ExternalClockSynchronization . . . . . . . . . . . . . . . 90Figure 59 COBAM: Interfaces and LED Indications. . . . . . . . . . . . . . . . . . . . . . . . 91Figure 60 COBAM: Location of DIP Switches S1 and S2 . . . . . . . . . . . . . . . . . . . 93Figure 61 COBAM: DIP Switch Settings of PCM Line . . . . . . . . . . . . . . . . . . . . . . 94Figure 62 COBAM: DIP Switch Setting PCM30 120 . . . . . . . . . . . . . . . . . . . . 94Figure 63 COBAM: DIP Switch Setting PCM30 75 . . . . . . . . . . . . . . . . . . . . . 94Figure 64 COBAM: DIP Switch Setting PCM30 100 . . . . . . . . . . . . . . . . . . . . 95Figure 65 COBAM: DIP Switch Settings of External Clock Synchronization . . . . . 96Figure 66 COREXT: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Figure 67 COSA6P16: Appearance and LED Indications . . . . . . . . . . . . . . . . . . . 99Figure 68 COSA: Location of DIP Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101Figure 69 COSA: DIP Switch Settings of Impedance . . . . . . . . . . . . . . . . . . . . . 102Figure 70 COSA4P12: Appearance and LED Indications (Front View) . . . . . . . . 103Figure 71 COSA4P12: Appearance (Top View). . . . . . . . . . . . . . . . . . . . . . . . . . 105Figure 72 CU: Appearance and LED Indications (Front View). . . . . . . . . . . . . . . 107Figure 73 DCBCTRLAV1: Interfaces and LED Indications . . . . . . . . . . . . . . . . . 111Figure 74 DCBCTRLDV*: Interfaces and LED Indications. . . . . . . . . . . . . . . . . . 113Figure 75 DCBCTRLM-2: Appearance and LED Indications . . . . . . . . . . . . . . . . 116Figure 76 M:DCBCTRLV1V2: Interfaces and LED Indications. . . . . . . . . . . . . 118Figure 77 DCBCTRLV1V2: DIP Switch Settings (Battery Capacity) . . . . . . . . 119Figure 78 DCBCTRLV1V2: DIP Switch Settings (Slot-ID) . . . . . . . . . . . . . . . . 120Figure 79 M:DCBCTRLV3: Interfaces and LED Indications. . . . . . . . . . . . . . . . . 121Figure 80 DCBCTRLV3: DIP Switch Settings (Battery Manufacturer) . . . . . . . . . 122Figure 81 DCBCTRLV3: DIP Switch Settings (Battery Capacity) . . . . . . . . . . . . 123Figure 82 DCBCTRLV3: DIP Switch Settings (Slot-ID) . . . . . . . . . . . . . . . . . . . . 123Figure 83 DCM-2: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124Figure 84 DCREFE: Appearance and LED Indications . . . . . . . . . . . . . . . . . . . . 125Figure 85 DCU: Interfaces and LED Indications (Front View) . . . . . . . . . . . . . . . 128Figure 86 DCU: Appearance and Interfaces (Back Side) . . . . . . . . . . . . . . . . . . 129Figure 87 DIAMCO: DIP Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132Figure 88 DIAMCO: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . . . 133Figure 89 DIAMCO V6: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . 135Figure 90 DIPLEXER: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . 137Figure 91 DPSK: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . 138Figure 92 DUAMCO: DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

8 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f1647

Figure 93 DUAMCO 2: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . 143Figure 94 DUAMCO 4: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . 144Figure 95 DUAMCO 8: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . 145Figure 96 DUBIAS: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 146Figure 97 DUSTFILM-2: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Figure 98 ECU: Interfaces and LED Indications (Front View). . . . . . . . . . . . . . . . 149Figure 99 FANM: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153Figure 100 FAN: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153Figure 101 FDUAMCO: Interfaces and LED Indications. . . . . . . . . . . . . . . . . . . . . 156Figure 102 FDUAMCO: DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157Figure 103 FDUAMCO and COAMCO: 8:2 Configuration . . . . . . . . . . . . . . . . . . . 158Figure 104 FIPLUB: Interfaces and LED Indications (Variant Example). . . . . . . . . 160Figure 105 FIPLUB: Interfaces and LED Indications (Variant Example). . . . . . . . . 161Figure 106 FIPLUX: Interfaces and LED Indications (Variant Example). . . . . . . . . 163Figure 107 FIPLUX: Interfaces and LED Indications (Variant Example). . . . . . . . . 164Figure 108 FlexCU: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . . . . . 167Figure 109 FWB: Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170Figure 110 GCU: Interfaces and LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . 172Figure 111 HEATER: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . 176Figure 112 HEATER-2: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . 177Figure 113 HEATERM-2V1: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178Figure 114 HEX: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179Figure 115 HPDU: Appearance and Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Figure 116 MEF: Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Figure 117 MEF150V4: Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183Figure 118 MEFM-2: Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184Figure 119 OPEXAL: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185Figure 120 OVPT: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188Figure 121 OVPT: Signals on Abis Interface Terminal Block for External Wiring . . 189Figure 122 OVPTKOAX: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . 190Figure 123 OVPTM: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 192Figure 124 OVPTCOAXM: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . 196Figure 125 TMA: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Figure 126 STMAE* / STMARE / STMA850: Appearance and Interfaces . . . . . . . 200Figure 127 STMAD: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 200Figure 128 DTMADV1: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . 201Figure 129 DTMAV2: Appearance and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . 201Figure 130 M:TMB-2V1: Connectors and Switches . . . . . . . . . . . . . . . . . . . . . . . . 203

A50016-G5100-A083-01-7620

9

HWMN:BTSE Modules

Id:0900d805800f1647

List of TablesTable 1 A:DUMACO: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Table 2 A:DUMACO: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Table 3 A:DUAMCO: DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Table 4 A:OVP: Interface Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Table 5 NTPMKU: Pin Assignment of the Terminal Block . . . . . . . . . . . . . . . . . 29Table 6 AC/DCA: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Table 7 AC/DCA: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Table 8 AC/DCDV1: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Table 9 AC/DCDV1: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Table 10 AC/DCDV1: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Table 11 AC/DCV1: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Table 12 ACPSC/DCPSC: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Table 13 ACPSC/DCPSC: Alarm Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Table 14 ACPSC: Assignment of PSC Connector . . . . . . . . . . . . . . . . . . . . . . . . 43Table 15 ACPSC: Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Table 16 M:ACTC-4V1: Switch Settings X24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Table 17 ACTP: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Table 18 ACTP: DIP Switch Settings: Cabinet Address . . . . . . . . . . . . . . . . . . . . 57Table 19 ACTP: DIP Switch Settings: Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . 57Table 20 AGENT: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Table 21 AGENT: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Table 22 BCOM: LED Indications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Table 23 BCOM 6:6 Connector Assignment for Cell Configuration 2/2/2 . . . . . . . 68Table 24 BCOM 12:6 Connector Assignment for Cell Configuration 6/6/0 . . . . . . 71Table 25 CCINT: LED Indications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Table 26 CCINT: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Table 27 COAMCO: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Table 28 COAMCO: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Table 29 COBA2P8: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Table 30 COBA2P8: Front Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Table 31 COBA2P8: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Table 32 COBA2P8: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Table 33 COBA4P12: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Table 34 COBA4P12: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Table 35 COBAM: LED Indications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Table 36 COBAM: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Table 37 COBAM: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Table 38 COSA6P16: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Table 39 COSA4P12: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104Table 40 CU: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Table 41 CU: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Table 42 CU: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Table 43 DCBCTRLAV1: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111Table 44 DCBCTRLAV1: Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Table 45 DCBCTRLD: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

10 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f1647

Table 46 DCBCTRLD: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Table 47 DCBCTRLD: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Table 48 DCBCTRLM-2: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Table 49 M:DCBCTRLV1V2: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 50 DCBCTRLV1V2: DIP Switch Settings (Slot-ID). . . . . . . . . . . . . . . . . 120Table 51 DCBCTRLV3: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122Table 52 DCBCTRLV3: DIP Switch Settings (Battery Manufacturer) . . . . . . . . . 122Table 53 DCBCTRLV3: DIP Switch Settings (Slot-ID). . . . . . . . . . . . . . . . . . . . . 123Table 54 DCREFE: LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125Table 55 DCREFE: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126Table 56 DCU: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129Table 57 DCU: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Table 58 DCU: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Table 59 DIAMCO: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132Table 60 DIAMCO: DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132Table 61 DIAMCO V3V5: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134Table 62 DIAMCO V6: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135Table 63 DIPLEXER: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137Table 64 DPSK: Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138Table 65 DUAMCO: LED Signalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140Table 66 DUAMCO: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141Table 67 DUAMCO: DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141Table 68 DUBIAS: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146Table 69 ECU: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150Table 70 ECU: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150Table 71 ECU: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150Table 72 DUAMCO / FDUAMCO Hardware Compatibility. . . . . . . . . . . . . . . . . . 155Table 73 FDUAMCO: LED Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157Table 74 DIAMCO: DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157Table 75 FIPLUB: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162Table 76 FIPLUB: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162Table 77 FIPLUX: LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165Table 78 FIPLUX: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165Table 79 FlexCU: LED Indications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168Table 80 FlexCU: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168Table 81 FlexCU: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Table 82 GCU: LED Indications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Table 83 GCU: Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Table 84 GCU: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174Table 85 HEATERV1/V2: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176Table 86 HEATER-2V1: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Table 87 HEATER--2DCV1: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178Table 88 HPDU: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Table 89 OPEXAL: ACTM Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186Table 90 OPEXAL: Alarm Connector Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186Table 91 OVPT: PCM Interface to the COBA/COSA (Soldering Side: 25 Pin Sub-D

Connector to EMI-Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

A50016-G5100-A083-01-7620

11

HWMN:BTSE Modules

Id:0900d805800f1647

Table 92 OVPT: Abis Interface to the BTSE External Cabling . . . . . . . . . . . . . . 189Table 93 OVPT: Monitoring Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189Table 94 OVPTKOAX: PCM Interface to the COBA/COSA (Soldering Side: 25 Pin

Sub-D Connector to EMI-Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190Table 95 OVPTKOAX: Abis Interface (PCM0, 75 ) . . . . . . . . . . . . . . . . . . . . . 191Table 96 OVPTKOAX: Abis Interface (PCM1, 75 , if installed) . . . . . . . . . . . . 191Table 97 OVPTKOAX: Monitoring Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . 191Table 98 OVPTM: Monitoring Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Table 99 OVPTM: Monitoring Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Table 100 OVPTM: Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Table 101 OVPTM: RS232/Wave Configuration Interface . . . . . . . . . . . . . . . . . 193Table 102 OVPTM: LMT Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194Table 103 OVPTM: Abis Interface to COBA/TIF. . . . . . . . . . . . . . . . . . . . . . . . . . 194Table 104 OVPTCOAXM: Connectors X13/14, X17/19 . . . . . . . . . . . . . . . . . . . . 196Table 105 OVPTCOAXM: Connectors X20/21, X18/22 . . . . . . . . . . . . . . . . . . . . 196Table 106 OVPTCOAXM: 4 Pin Terminal Block x6 . . . . . . . . . . . . . . . . . . . . . . . 196Table 107 OVPTCOAXM: Cable Connections for the Abis Interface . . . . . . . . . . 196Table 108 TMA: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Table 109 TMA: Fault Propagations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Table 110 DTMA: Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201Table 111 DTMA: Fault Propagations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202Table 112 TMB: Connector Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204Table 113 TMB: Connector X5 Main Load Relay. . . . . . . . . . . . . . . . . . . . . . . . 204Table 114 TMB: Connector X7 Switching Signals for Heater and Fan. . . . . . . . 204Table 115 TMB: Test Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

12 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800a3ce0

Reason for Update

Reason for UpdateIssue History

Issue 01 for Release BR8.0 (2006/15/12)

AC/DCD (2.7.2)

Additional hardware: AC/DCDV2

Issue Date Summary

Issue history for this document with order number A30808-X3247-K83-*-7620

01 06/2002 New release

02 07/2002 Revised description: AC/DC, DCBP, DCBCTRL

03 09/2002 Extension due to additional hardware












15 09/2005 Minor changes

16 10/2005 Extension due to additional hardware: FDUAMCOV3

17 11/2005 Extension due to additional hardware: DTMADV2

18 03/2006 Additional hardware: M:ACTC-4V1, DCBCTRLDV3, DIAMCOV6, FDUAMCOREV3, OPEXAL10V1

Revised description: ACTP

Issue history for this document with order number A50016-G5100-A083-*-7620

01 11/2006 Extension due to additional hardware: HEATERV3, HEATER-2V3, AC/DCDV2, MEF150V4, ACDCM-2V2, ACDCM-2V3, ACDCM-2V4, M:TMB-2V1, HEATERM-2V1, ACPROT-2M/UV1, HPDU2DV2

Revised description: M:ACTC-4V1

A50016-G5100-A083-01-7620

13

HWMN:BTSE Modules Reason for Update

Id:0900d805800a3ce0

AC/DCM-2 (2.7.3)

Additional hardware: AC/DCM-2V2 Additional hardware: AC/DCM-2V3 Additional hardware: AC/DCM-2V4

ACPROTECT (2.8)

Additional hardware: ACPROT-2M/UV1

ACT (2.9)

Revised description: M:ACTC-4V1

HEATER (2.36)

Additional hardware: HEATERV3 Additional hardware: HEATER-2V3 Additional hardware: HEATERM-2V1

HPDU (2.38)

Additional hardware: HPDU2DV2

MEF (2.39)

Additional hardware: MEF150V4

TMB (2.43)

Additional hardware: M:TMB-2V1

14 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800a3ce0

Reason for Update

A50016-G5100-A083-01-7620

15

HWMN:BTSE Modules Introduction

Id:0900d80580059111

1 Introduction

1.1 Purpose of the ManualThe purpose of this document is to identify specific design and construction issues. The Hardware Manual Modules (HW:BTSE Modules) describes: The appearance The LED indications The adjustments The DIP switch settings

of the modules.

The Hardware Manual Modules contains all hardware components that are relevant for maintenance and installation according to the IMN, ITMN and MMN Manuals.

1.2 Structure of the ManualThe HW:BTSE manual is structured in the following way:1. Introduction - purpose and structure of the manual.2. Modules3. Abbreviations4. Index

Remark to Subchapter Modules

In order to find the correct module in this manual it is important to know that two different expressions exist for each module:1. Module Name2. Mnemonic of element (for ordering)

For example:

The alphabetical order of the subchapters in the chapter Modules is sorted in the first level by the module name and in the second level by the mnemonic.

The title of the subchapters returns the module name and the list below returns the mnemonic of the element.

Module Name Description Mnemonic of Element

COBA For micro BTS M:COBAM

DUAMCO Duplexer Amplifier Multicoupler 4:2 P-GSM 900

DUAMCO4G

A:DUAMCO Add-on device: DUAMCO 2:1 P-GSM 900

A:DUAMCO2MPG

FICOM Plus base 2:1 R-GSM 900 FIPLUB2R

FICOM Plus extension 2:1 GSM 1800 FIPLUX2D

16 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d80580059111

Introduction

1.3 Rack Outlines

1.4 General Information on BTSE LEDsThis book contains the common LED signal mechanisms of the BTSE boards. All the modules of the BTSE have LEDs to indicate their status, except BATTERY, DIPLEXER, DUBIAS, FAN, HPDU and TMA.

After the startup, a hardware test will be executed on each module of the BTSE. Detected hardware errors will be indicated by the flashing reset LED where the number of the failed test is binary coded in the flashing sequence. The test number is an 8-bit value where the LSB (Least Significant Bit) is transferred first and the MSB (Most Sig-nificant Bit) last.

General meanings of the LED color when the LED is on: Green: Hardware and software are O.K. Red: After reset, during software initialization (one for each processor) Yellow: Active module of redundant board

There are additional LEDs and further meanings specific to each type of module, these are described in the respective section. There are also LEDs which show the status of software. These are described in the following module descriptions.

Whenever useful, the position of the module is indi-cated in a sketch of the corresponding racks.

Generally, sketches of the BS-240 II will be shown as an example, using the following abbreviations: ER: Extension Rack BR: Base Rack SR: Service Rack

ER BR SR

A50016-G5100-A083-01-7620

17

HWMN:BTSE Modules Introduction

Id:0900d80580059111

1.5 Removing and Inserting ModulesThere are two variants for fastening modules in the subracks.

Some modules, e.g., the COBA and COSA, are equipped with a lever mechanism at their front panel. For removing or inserting these modules, they can be fastened / unfas-tened by swivelling the levers at the top and bottom edges of the module.

Other modules, e.g., the CU, DIAMCO, DUAMCO, FICOM, AC/DC, are fastened with TORX-headed knurled screws. Replacement of these modules requires special tools.

Figure 1 Module Fastening Variants

The TMA (Tower Mounted Amplifier) must be replaced complete with its housing (to be mounted on / unmounted from the mast).

The semi-rigid / flexi cables on the CU, DIAMCO, DUAMCO and FICOM must be fastened / unfastened with a torque spanner (2 sizes).

g It must be ensured that the modules are only replaced by modules with the same (or a compatible) HW and SW functional status!

Modules with switches or jumpers must be compared with the removed module for safety reasons.

The modules should be removed and inserted as fast as possible, in order to prevent reading in false module addresses from the CAN BUS.

lever mechanism in open position

push together

lever mechanism in locked position torx screw

18 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d80580059111

Introduction

Handling Modules with Code Keys

To prevent the installation of the modules at incorrect mounting positions, code keys are used on all relevant plug-in modules.

Figure 2 Location of the Plug-in Module Code Keys

In order to avoid module and backplane connector damage when modules are removed from / inserted into a base station frame, please observe the following:

In general, after having removed a module from a base station frame, please make sure that the modules code keys (at the rear connector terminals) are mechanically intact, and that a code key plug has not been torn out from its socket and is now jammed in the backplane.

When replacing a module, please make sure

That the code keys of the new module have the same setting as those of the old one (see figure below)

That all code keys (also those of the old module) are mechanically intact That a code key plug has not been torn out from its socket and is now jammed in the

backplane

Figure 3 Location of the Plug-in Module Code Key Number

When inserting a module, do not use excessive pressure.

Code Keys

2

code key number

A50016-G5100-A083-01-7620

19

HWMN:BTSE Modules Modules

Id:0900d805800f164a

2 Modules

20 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.1 A:COOLINGThe A:COOLING add-on module dissipates heat coming from the combiner.

g If an A:TIFNTPM is used in direct connection with an A:DUAMCOM, they must be separated by an A:COOLING module to avoid overheating of the A:TIFNTPM module.

Without A:COOLING, temperatures within limits for the A:TIFNTPM module (max 55 C / 131 F) can no longer be guaranteed at external temperatures above 45 C / 113 F.

The module is fed by a 12 V power supply coming from A:TIFNTPM.

Use of module A:COOLING: Simultaneous application of module A:DUAMCO and A:TIFNTPM Sequence of the modules from bottom to top: A:DUAMCO, A:COOLING, up to 4

A:TIFNTPMs

g No matter whether A:DUAMCO2:1 or A:DUAMCO4:1 is used, the module A:COOL-ING must be inserted in any case.

Figure 4 A:COOLING: Configuration with 2 NTPMs and the A:DUAMCO

Types of A:COOLING

A:COOLINGV1 S30861-U2270-X

A:COOLINGV2 S30861-U2278-X

A:TIFNTPM

A:COOLING

A:DUAMCO

eMicroAdd-onMain Power

ATIF2

ATIF1

12 V forthe FAN

230 VPowerSupply

OUT

IN

A50016-G5100-A083-01-7620

21


Id:0900d805800f164a

2.2 A:DUAMCOThe A:DUAMCO (Add-on Duplex Amplifier Multicoupler) is a combining module with the following general functions: Duplexing of the RX and the TX path, to be fed to a common antenna Amplifying and splitting of the RX signal from the antenna to the CUs Coupling of the TX paths from several CUs to the antenna TMA (Tower mounted Amplifier) power supply Antenna monitoring

The A:DUAMCO has two different operating modes: The high amplifying AMCO mode The low amplifying MUCO mode for use with the tower-mounted amplifier (TMA) or

in a multicoupler cascade

The hybrid combining can be done with the add-on modules A:DUAMCO2Mx to combine 2 carriers and A:DUAMCO4Mx to combine 4 carriers.

Types of A:DUAMCO Frequency Range

A:DUAMCO2MPGV1 S30861-U2160-X DUAMCO 2:1 P-GSM 900

A:DUAMCO2MPSV1 S30861-U2320-X DUAMCO 2:1 shifted P-GSM 900

A:DUAMCO2MDV1 S30861-U2161-X DUAMCO 2:1 GSM 1800

A:DUAMCO2MPV1 S30861-U2162-X DUAMCO 2:1 GSM 1900

A:DUAMCO2MREV1 S30861-U2198-X DUAMCO 2:1 GSM-RE

A:DUAMCO4MPGV1 S30861-U2163-X DUAMCO 4:1 P-GSM 900

A:DUAMCO4MPSV1 S30861-U2321-X DUAMCO 4:1 shifted P-GSM 900

A:DUAMCO4MDV1 S30861-U2164-X DUAMCO 4:1 GSM 1800

A:DUAMCO4MPV1 S30861-U2165-X DUAMCO 4:1 GSM 1900

A:DUAMCO4MREV1 S30861-U2199-X DUAMCO 4:1 GSM-RE

22 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 5 A:DUAMCO: 4:1 and 2:1 Interfaces

1

2

3

4

off

on

on

on

DIP Switch Antenna connector

e.g., A:DUAMCO4M

CAN-Bus

RX connectors Antenna connector TX connectors

LEDs, meaning see below

Testout connector

DIP Switch, setting see below. The DIP Switch

LEDs, meaning see below

e.g., A:DUAMCO2M

RX connectors TX connectors

CAN-Bus

position of a A:DUAMCO 2:1 is different.

A50016-G5100-A083-01-7620

23


Id:0900d805800f164a

Switch

Figure 6 A:DUAMCO: DIP Switch (Factory Setting)

The switch setting for A:DUAMCO is described in Table 3.

g In BR 5.5 there is no use of TMA with BS-82 eMicro, so switch 1 must be set to off!

LED Signal Meaning

TMA Off Module is in AMCO mode

Green Module is in MUCO mode, TMA-DC is OK

Red Module is in MUCO mode, TMADC is not OK This LED is on for 5 sec. only.

ALAMRM The VSWR is above the threshold.

RESET The module is in reset.

POWER The DC power is present.

Table 1 A:DUMACO: LED Indications

Connector Meaning

RX 0...3 RX-output 0...3

The A:DUAMCO 4:1 provides 4 RF output ports for the RX signals for connection with module DCU: RX-input.

TX 0...3 TX-input 0...3

The DUAMCO 4:1 provides 4 TX-input ports for the TX signals for connection with module DCU: TX-output.

Testout RF Test Signal Output

SMA female connector is provided for RF test purposes

ANT Antenna Output

Output for antenna connection

CAN Bus Interface Power supply/CAN bus (broadband cable). The A:DUAMCO provides a CAN bus interface at the backplane connector for the controlling/monitoring signals.

Table 2 A:DUMACO: Connectors

1 2 3 4

off off off on

24 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

The setting of the switches 2 - 4 determines the attenuation at the A:DUAMCO. The total attenuation of cable (between TMA and A:DUAMCO) and DIP switch must be 6dB.

"X": any position allowed.

g Switch 1 does not work when a TMA alarm is present.

Function Switch 1 Switch 2 Switch 3 Switch 4

TMA off / AMCO mode Off X X X

TMA on / MUCO mode On X X X

Attenuator LNA 0 dB Off X X X

Attenuator LNA 0 dB On Off Off Off

Attenuator LNA 1 dB On On Off Off

Attenuator LNA 2 dB On Off On Off

Attenuator LNA 3 dB On On On Off

Attenuator LNA 4 dB On Off Off On

Attenuator LNA 5 dB On On Off On

Attenuator LNA 6 dB On Off On On

Attenuator LNA 7 dB On On On On

Factory setting Off Off Off On

Table 3 A:DUAMCO: DIP Switch Settings

A50016-G5100-A083-01-7620

25


Id:0900d805800f164a

2.3 A:DUXMEGThe A:DUXMEG (Add-on Duplex Filter for E-GSM) is a duplexer for the E-GSM 900 fre-quency range with the following general functions: Coupling of the transmitting path (TX) from the DCURGs to the antennas Splitting the receiving path (RX) from the antennas to the DCURGs

If the E-GSM 900 frequency band is to be provided, the duplexers will not be part of the DCU modules. Due to their large volume, the E-GSM 900 duplexers are configured as add-on modules (A:DUXMEG) on top of the base unit and a DCURG module is used as carrier unit. The combination of DCURG and DUXMEG has the same function as a single DCUDUX in other frequency ranges.

The TX outputs and the RX inputs of the DCURG are connected to A:DUXMEG via semi-rigid cables. The antenna output cables from A:DUXMEG run over the backplane and leave the eMicro at the bottom.

Up to 2 A:DUXMEG add-on modules can be installed at the top of the respective master cabinet as well as the optional extension cabinet.

Figure 7 A:DUXMEG: Interfaces

Types of A:DUXMEG

A:DUXMEGV1 S30861-U2176-X

TX input/female CU0

TX input/female CU1

antennaoutput CU1

antennaoutput CU0

RX output/male CU1

RX output male CU0

26 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.4 A:OVPThe A:OVP (Add-on Overvoltage Protection) is a lightning protection module for 16 Environmental Alarm (ENVA) lines.

The A:OVP16AM does not need any power supply and there is no PID EEPROM on it. The module name and the serial number are printed on a bar code label only.

The 16 alarm lines and 16 ground lines are connected to an external connector field using a cable containing 16 twisted-pair wires.

The 16 alarm lines are guided through the flash duct to the A:OVP16AM. Two alarm lines are connected to one overvoltage protector module, the two ground lines are tied together to the ground pin of the module.

Figure 8 A:OVP: Interfaces

Types of A:OVP

A:OVP16AM S30861-U2139-X

Signal Overvoltage Protector Signal

AL0_IN 1-1 5-1 AL8_IN

AL1_IN 1-2 5-2 AL9_IN

AL2_IN 2-1 6-1 AL10_IN

AL3_IN 2-2 6-2 AL11_IN

AL4_IN 3-1 7-1 AL12_IN

AL5_IN 3-2 7-2 AL13_IN

AL6_IN 4-1 8-1 AL14_IN

AL7_IN 4-2 8-2 AL15_IN

Table 4 A:OVP: Interface Assignment

A50016-G5100-A083-01-7620

27


Id:0900d805800f164a

2.5 A:TIFNTPMA:TIFNTPM (Terrestrial Interface for Network Termination Primary Access Multiplex) is an add-on module containing either an NTPMGF or an NTPMKU module, to be used as Abis interface (in the connection between BTS and BSC).

The NTPM is not part of A:TIFNTPM but it will be supplied by the provider as a termina-tion for the PCM 30 lines.

Figure 9 A:TIFNTPM: Interfaces

Types of A:TIFNTPM

A:TIFNTPM S30861-U2200-X

Plug to CORE BP terminal block 12V toA:COOLING

HeaterCabling

U Interface(Abis) cabling

M:NTPMCON

28 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 10 A:TIFNTPM: Mechanical Sketch Top View

If other add-on modules are mounted above A:TIFNTPM, they have to be removed in order to allow the substitution of an NTPM. The NTPM is inserted into the A:TIFNTPM from above with its front panel on the front side of the eMicro BTS.

g If an A:TIFNTPM is used in direct connection with an A:DUAMCOM, they must be separated by an A:COOLING module to avoid overheating of the A:TIFNTPM module.

The Abis interface cables must be routed through the flash duct.

In case of NTPMGF, the two glass fibres are connected to a special interconnection box at the NTPMGF module.

In case of NTPMKU the copper wires are connected at a terminal block according to the following table:

NTPM

6

1

6

1

M:ATIFCON Temperature switchBS = Backplane SideMIS = Module Insertion SideFS = Front Side

Plug to CORE BP Plug to cascaded NTPM

terminal block 12V to A:COOLING

HeaterCabling

U Interface(Abis) cabling

FAN

MIS

terminal block in case of NTPMKUAdditional box in case of NTPMGF

Additional box for the fibre optics

terminal blockfor UK

LED and test outputs

Plug toNTPMCON

Plug toM:ATIFCON

M:NTPMCON

FAN connection

AMP plug for UK2TemperatureSensor

A50016-G5100-A083-01-7620

29


Id:0900d805800f164a

If two A:TIFNTPMs are used, they need not necessarily be placed over one another. The two modules have to be directly connected to the two ATIF ports on the backplane of the eMicro BTS, each by means of a 40-wire flat ribbon cable (up to 80 cm / 31.5 inches long) terminated on both sides with BK-MOD plugs, to be inserted respectively into the ATIF port and the input/lowermost socket on the corresponding M:ATIFCON.

In order to manage the cables as easily as possible, the lowermost A:TIFNTPM should be bridged to ATIF1, the uppermost one to ATIF2.

Pin Signal

Pin 1 UK2out_b

Pin 2 UK2out_a

Pin 3 Ground

Pin 4 not used

Pin 5 UK2in_a

Pin 6 UK2in_b

Table 5 NTPMKU: Pin Assignment of the Terminal Block

30 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 11 A:TIFNTPM: Configuration with 2 NTPMs and the A:DUAMCO

A:TIFNTPM

A:TIFNTPM

A:COOLING

A:DUAMCO

eMicro

TIF Connection NTPM up to80 cm / 31.5 inches

ATIF1

ATF2 Add-on Main Power

230 VPowerSupply

12 V forthe FAN

OUT

INM:TIFCON

OUT

IN

A50016-G5100-A083-01-7620

31


Id:0900d805800f164a

2.6 ABISCON

Alternatively, the BTSE may be equipped with an OVPT interface module instead of the ABISCON, or both interface module types are omitted. In the latter case, the Abis lines are connected directly to the BTSEs EMI-Panel via a 25 pin Sub-D connector.

The ABISCON (Abis Connector) is an optional inter-face module with the following general functions: Easy connection of PCM (Abis) lines to the BTSE Provision for connecting external monitoring

equipment without interruption. The lines are decoupled by resistors in order to avoid interfer-ences.

Depending on the BTSE type, up to 2 ABISCON inter-face modules may be installed in order to handle up to 8 Abis ports (4 ports per ABISCON). At the EMI-Panel of the BS-240XS Base Rack, only one Abis connector module can be installed.

Types of ABISCON

M:ABISCON S30861-Q2189-X 100/120 symmetrical lines

M:ABISCONCX S30861-Q2190-X 75 coaxial lines

ER BR SR

inside EMI-Panel

32 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.6.1 M:ABISCON

Figure 12 ABISCON: Appearance

M:ABISCONV1 offers up to 4 Abis connections on a twisted pair cable terminal.

For connector layout and signal assignment, please refer to chapter M:OVPT.

2.6.2 M:ABISCONCXM:ABISCONV1 offers up to 4 Abis connections on an SMA connector terminal.

For connector layout and signal assignment, please refer to chapter M:OVPTKOAX.

A50016-G5100-A083-01-7620

33


Id:0900d805800f164a

2.7 AC/DC

AC/DC is a power supply module which provides all -48 V direct current consumer loads within the BTSE.

Types of AC/DC

AC/DCA S30861-U4093-X

AC/DCD S30861-U4102-X

AC/DCM-2 S30861-U2389-X

AC/DC S30861-U2008-X

ACPSC

ACPSC/U S30861-S2118-X

DCPSC S30861-U2254-X

ER BR SR

34 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.7.1 AC/DCA

For primary voltage of 230 V AC 50/60 Hz and DC output voltage of -48 V.

Figure 13 AC/DCA: Appearance and LED Indications

Types of AC/DCA

AC/DCAV1 S30861-U4093-X

Test SocketsLEDs

A50016-G5100-A083-01-7620

35


Id:0900d805800f164a

LEDs

Connectors

LED Signal Meaning

FF Red Fan Fail

OV Red Over Voltage

TC Yellow Terminal Control

IP Green Input Healthy

CL Red Current limit

OT Red Over Temperature

SB Yellow Standby

OI Green Output Current Healthy

OP Green Output Healthy

Table 6 AC/DCA: LED Indications

Connector Meaning

+I, -I Test Sockets for Output Current

Table 7 AC/DCA: Connectors

36 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.7.2 AC/DCD

For primary voltage of 230 V AC 50/60 Hz and DC output voltage of -48 V.

Figure 14 AC/DCD: Appearance and LED Indications

Types of AC/DCD

AC/DCDV1 S30861-U4102-X

AC/DCDV2 S30861-U4304-X

LED Signal Meaning

AC ON Green AC Input Power present

CL Yellow Current Limit

RFA Red Rectifier Fail

Table 8 AC/DCDV1: LED Indications

Switch Meaning

AC AC main switch

Table 9 AC/DCDV1: Switches

Connector Meaning

I-,I+ Test Sockets for Output Current

Table 10 AC/DCDV1: Connectors

AC Switch

AC ON

CL

RFA

Test Sockets

A50016-G5100-A083-01-7620

37


Id:0900d805800f164a

2.7.3 AC/DCM-2The tasks of the AC/DC rectifier of eMicro II are: Supply of all -48 V consumers within the BTSE Generating of alarms in case of AC mains or module failures

Figure 15 AC/DCM-2: Appearance and LED Indications

Types of AC/DCM-2

AC/DCM-2V1 S30861-U2389-X

AC/DCM-2V2 S30861-U2419-X

AC/DCM-2V3 S30861-U2464-X

AC/DCM-2V4 S30861-U2483-X mandatory for 7 Ah battery pack

INPUT OK

OUTPUT OK

The LEDs are off, if the internal supply voltage is down

38 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.7.4 AC/DC

For primary voltage of 230VAC 50/60Hz and DC output voltage of -48 V.

Figure 16 AC/DC: Appearance and LED Indications

Types of AC/DC

AC/DCV1 S30861-U2008-X

AC Input

Test Connector

Fuses 10A(quick acting)

LED

A50016-G5100-A083-01-7620

39


Id:0900d805800f164a

LED Signal Meaning

ON Green Rectifier OK

Pale green Rectifier OK, but low output voltage (caused by Remote_Off from controller)

Orange Power limit active

Red Output short circuit, unit faulty or overtemperature

Table 11 AC/DCV1: LED Indications

40 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.7.5 ACPSC

The module ACPSC has to be used for AC power supply, the module DCPSC has to be used for DC power supply. Backup battery is only possible for ACPSC!

The front sides of the modules ACPSC and DCPSC have the same design and func-tional units (breakers, reset, LEDs).

Figure 17 ACPSC/DCPSC: Appearance and LED Indications

Types of ACPSC

ACPSCV1 S30861-U2156-X

ACPSCV2 S30861-U2348-X

LED Signal Meaning

AC Green Primary power source present. The LED is on if the alarm MBR is not activated.

The LED is off in case of DCPSC.

DC Green DC output voltage within specified tolerance. The LED is on if the alarm 48OTB is not activated; the LED is off if the internal supply voltage of the controller board is down.

Table 12 ACPSC/DCPSC: LED Indications

RESET

Breakers

COBA, DCU 0

DCU 1

Add-on modules

External equipment

BAT FAILRESETAC OK

TEMP FAILHW/SW OKDC OK

A50016-G5100-A083-01-7620

41


Id:0900d805800f164a

ACPSC and DCPSC have different backplanes, but the connector pinning is the same.

Figure 18 ACPSC: Interfaces

HW/SW OK

Green Startup and selftest of PSCV1 finished and OK

BAT FAIL Red Battery system or temperature sensor on battery system is faulty. The LED is on if the alarms BAT_FAIL and/or TEMP_SENSE_FAIL are activated.

The LED is off in case of DCPSC.

TEMP Red Over- / Undertemperature protection. The LED is on if the over- or undertemperature protection is triggered.

RESET Red During RESET this LED is active. After Power On of the AC/DC controller this LED is on. In case the microcontroller has come into normal operation (is able to re-trigger watchdog and activate the CAN Bus interface), the LED goes off.

LED Signal Meaning

Table 12 ACPSC/DCPSC: LED Indications

ACPSC backplane side PID

AC power input

Connector for HEATER

Main Switch (not for ACPSCV2)DC external

Connector forBATTERY

Connector for COBA, DCU 0, DCU 1,Add-on modules

Connector Backplane Alarms

Connector ENVA BTS

MUE (-)PUE (+)

L1NPE

42 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 19 DCPSC: Interfaces

DC import

Main Switch

Connector for HEATER

PUE (+)MUE (-)

PID

DC external

Connector for COBA, DCU0, DCU1,Add-on modules

Connector Back-plane Alarms

ConnectorENVA BTS

Name Meaning

AUX0 DC-Output: 0V Pin for AUX48V auxiliary DC supply voltage and refer-ence potential for all control signals below

AUX48V DC-Output: Auxiliary 48 V DC supply voltage (48 V 20%; 250 mA max)

R_OK Alarm Output: This output signals two alarm situations (see figure above):Switches S1 and S2 are normally closed.S1 has to be opened in case AC/DC rectifier module faulty and the rectifier is unable to supply the specified power. This may happen in case of low input voltage, control circuit of DC voltage, current/power limiter are faulty, overtemper-ature protection or any other internal protections are active. S2 has to be opened in case AC input voltage is low.

R_OFF Control Input: In case voltage applied 0.8V or input left open: normal operation. In case voltage applied 3.5 V, AC/DC shuts down output. Input resistance 10k.

Vadj Control Input: Input signal to control DC output voltage of AC/DC rectifier according to Uo Control on Vadj.

Table 13 ACPSC/DCPSC: Alarm Assignment

A50016-G5100-A083-01-7620

43


Id:0900d805800f164a

Signal Pin Pin Signal

PUE (0V) (20A) A1 9 n.c.

n.c. 1 10 n.c.

R_off (10mA) 2 11 n.c.

Vadj (10mA) 3 12 n.c.

AUX48V (10mA) 4 13 n.c.

AUX0V (250mA) 5 14 n.c.

OK (1mA) 6 15 Sense -(10 mA)

n.c. 7 A2 MUE (-48 V) (20 A)

Sense +(10mA) 8

Table 14 ACPSC: Assignment of PSC Connector

Alarm Meaning

MBR Mains Breakdown Alarm has to be activated if the AC/DC goes into a mains breakdown condition (voltage below limit).

BBR Battery Breakdown Alarm has to be activated if the battery voltage is below -43V0.5V

BCHF AC/DC rectifier module failure. Alarm has to be activated if the AC/DC is unable to supply the specified power. This may happen in case rectifier module is faulty, low input voltage, control circuit of temperature dependent nominal voltage, current/power limiter are faulty, overtemperature protection or any other internal protections are active.

48 OTB DC-Output Voltage on the load out of specified tolerance. Alarm has to be activated if the output voltage is out of spec-ified range of -39.5V...-56.7V or the voltage control loop is faulty. The alarm must not be triggered during Backup Oper-ation.

BAT_FAIL This alarm has to be activated in case the battery monitoring unit has found that the capacity of the battery is below a specified limit as a result of the battery test.

OVER_TEMP Alarm has to be activated in case of overtemperature

UNDER_TEMP Alarm has to be activated in case of undertemperature

BAT_DISCHARGE This alarm has to be activated in case the AC/DC system comes into backup operation (battery supplies load); this alarm must not be triggered during battery test.

TEMP_SENSE_FAIL This alarm has to be activated in case the resistance value of the temperature sensor of Battery 0 is out of the speci-fied range.

Table 15 ACPSC: Alarms

44 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.7.6 ACPSC/U

AC power supply and control unit for 115 V (eMicro BTSE).

Difference from ACPSC: no main switch the L1/N-connection of the AC power input is changed.

g For ACPSC/U a Field Wiring Box or ACPROTECT is needed. See chapters FWB or ACPROTECT.

2.7.7 DCPSC

See also chapter ACPSC.

Types of ACPSC/U

ACPSC/UV1 S30861-U2235-X

Types of DCPSC

DCPSCV3 S30861-U2254-X

A50016-G5100-A083-01-7620

45


Id:0900d805800f164a

2.8 ACPROTECTThe ACPROTECT (AC Input Lightning Protection) is installed as external unit to the BS-82 II cabinet to ensure lightning protection of the BTS subsystem. The ACPROTECT box also includes an AC breaker. The distance between ACPROTECT box and the BS-82 II cabinet shall not exceed 1.8 m. The AC supply cable for the cabinet is part of the ACPROTECT box.

Types of ACPROTECT

ACPROTECT

ACPROTECTV1 S30861-U2239-X



ACPROTECT-2M

ACPROTECT-2MV1 S30861-U2418-X

ACPROT-2M/UV1 S30861-U2455-X

46 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.8.1 ACPROTECT

Figure 20 ACPROTECT: Appearance

1) 2) 3)

7)

5)

6)

4) bottom

Note:1) ACmains supply2) grounding cable3) AC cable to BTS (protected)4) recommended mounting position5) ground bolt6) PE/N/L1 (in)7) PE/N/L1 (out)

A50016-G5100-A083-01-7620

47


Id:0900d805800f164a

2.8.2 ACPROTECT-2M

Figure 21 ACPROTECT-2M: Appearance

48 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.9 ACT

ACTC is part of the DC Panel in every rack. Each ACTC provides 16 alarms. The ACTC in the Base Rack is directly connected to the COBA, in every other rack it is connected to ACTP.

ACTP provides a connection to the COBA via the CAN BUS.

ACTM optionally provides 48 additional alarms and 8 outputs at the Base Rack. It is directly connected to the CAN BUS.

g The ACTM module consists of an ACTA (ACT-Alarm) and an ACTP module, which are directly plugged together. The ACTM must be replaced es a whole unit because the Product Identification Data of the whole unit is stored into the ACTP.

Internal and external alarms of all racks are collected by ACT (Alarm Collection Terminal) modules and channeled to the COBA in the Base Rack.

There are three types of ACT modules: ACTC (ACT-Connection) is the standard alarm

connection module. ACTP (ACT-Processor) is the CAN BUS inter-

face for the alarm connection modules. ACTM (ACT-Master) is an optional alarm con-

nection module for the Base Rack.

Types of ACT

ACTA: (Part of ACTM)

ACTAV2 S30861-Q2053-X

ACTC:

ACTC12V1 S30861-Q2138-X

ACTCV1 S30861-Q2029-X

ACTC-3V1 S30861-Q2194-X

ACTC-4V1 S30861-Q2267-X

ACTP:

ACTPV2 S30861-Q2052-X

ACTPV3 S30861-Q4088-X

ACTM:

ACTMV2 S30861-U2079-X

ER BR SR

ACTM inside EMI-Panel

A50016-G5100-A083-01-7620

49


Id:0900d805800f164a

Figure 22 ACT: Configurations

Some units have an independent access to the CAN BUS, e.g., DUAMCO and FICOM

2.9.1 ACTAFor base rack: part of ACTMV2

Figure 23 ACTA: Appearance

Base Rack Extension Rack Service Rack

ACTC ACTM

COBACAN BUS

ACTC

ACTP

ACTC

ACTP

(optional)

50 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 24 ACTA: Connector Locations

g In case of alarm signal modifications, please refer to the respective base station installation manual (IMN) for more information on the alarm signal assignment.

2.9.2 ACTC

2.9.2.1 ACTC12

Figure 25 ACTC12: Appearance

X1

X9

X8

X10

X6X7 X5

X4 X2X3

A50016-G5100-A083-01-7620

51


Id:0900d805800f164a

Figure 26 ACTC12: Connector Locations


2.9.2.2 ACTC

Figure 27 ACTC: Appearance

Alarm_IN

Temperature Sensors

116

BB0 BB1 BB2

SMOKE RDO SIS

HHHX X X0 1 2

WWW

1 2 3

W4

W5

W6

W7

W8

W9

BB3

52 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 28 ACTC: Connector Locations


2.9.2.3 ACTC-3

Figure 29 ACTC-3: Appearance


Alarm_IN

Temperature Sensor

124

BB0 BB1 BB2

SMOKE RDO SIS

HHHX X X0 1 2

WWW

1 2 3

W4

W5

W6

W7

W8

W9

Temperature Sensors

SMOKEsmoke sensor

RDOrack door open

24

Environmental Alarms

1

A50016-G5100-A083-01-7620

53


Id:0900d805800f164a

2.9.2.4 M:ACTC-4

Figure 30 M:ACTC-4V1: Appearance (Front View)


Figure 31 M:ACTC-4V1: Switch Locations (Top View)

Switches

Jumper X24

ON MAJor alarm is activated, occupying Alarm12, which is therefore not available on connection block X4. (dafault for service 1A cabinets)

OFF MAJor alarm is deactivated, Alarm12 is available on connection block X4. (dafault for all other cabinets)

Table 16 M:ACTC-4V1: Switch Settings X24

54 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.9.3 ACTMFor base rack: consists of ACTA and ACTP

Figure 32 ACTM: Appearance

ACTA

ACTP

ACTA

ACTP

A50016-G5100-A083-01-7620

55


Id:0900d805800f164a

2.9.4 ACTPFor extension and service rack/shelter

There are two DIP switch variants on the ACTP with either a horizontal arrangement (Figure 33) or a vertical arrangement (Figure 34) of the switches.

Figure 33 ACTP: Connector Locations (Horizontal DIP Switch Variant)

X6

X2 (opposite side)

X4

LEDs

Reset

X5 (opposite side)

DIP Switch

56 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 34 ACTP: Connector Locations (Vertical DIP Switch Variant)

LED Color Meaning

Green Hardware and Software are O.K. (tests successfully passed)

Red The microcontroller is resetting

Table 17 ACTP: LED Indications

X6

X2 (opposite side)

X4

LEDs

Reset

X5 (opposite side)

DIP Switch

A50016-G5100-A083-01-7620

57


Id:0900d805800f164a

Switch

The rack address is preset in the factory for the base rack, the extension rack 1, and the service rack 1. Additional racks require a setting on site.

Figure 35 ACTP: DIP Switch

Rack/Shelter

No. Type Switch 1 Switch 2 Switch 3

0 Base OFF / OPEN OFF / OPEN OFF / OPEN

1 Extension 1 ON / CLOSED OFF / OPEN OFF / OPEN

2 Extension 2 OFF / OPEN ON / CLOSED OFF / OPEN

3 Service 1 ON / CLOSED ON / CLOSED OFF / OPEN

4 Service 2/1A OFF / OPEN OFF / OPEN ON / CLOSED

5 Service 2 ON / CLOSED OFF / OPEN ON / CLOSED

6 Service 2 OFF / OPEN ON / CLOSED ON / CLOSED

7 Service 2 ON / CLOSED ON / CLOSED ON / CLOSED

Table 18 ACTP: DIP Switch Settings: Cabinet Address

Watchdog Switch 4

Enable (default) ON / CLOSED

Disable OFF / OPEN

Table 19 ACTP: DIP Switch Settings: Watchdog

ON

1 432

ON

OFF

1 432

OPEN

CLOSED

Settings for Base Rack

Vertical Type:

Horizontal Type:

OPEN

58 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.10 AGENTThe BS-242 AGENT is a compact transceiver unit. Up to 24 AGENTS can be connected to a BS-242 SERVER.

g Not part of BR8.0 and above

All tables and descriptions in this chapter are valid for all AGENTs above.

Figure 36 AGENT: with Indoor Cover

Types of AGENTs

R:AGENPGV1 S30861-C2008-X P-GSM 900

R:AGENPDV1 S30861-C2009-X GSM 1800

A50016-G5100-A083-01-7620

59


Id:0900d805800f164a

Figure 37 AGENT: with Outdoor Cover

AGENT LEDs, Test Connector, PID Connector:

The agent LEDs, a test connector and a PID connector can be accessed after removing a small cover plate located at the bottom of the agent.

Figure 38 AGENT: LED Indications

LED Signal Meaning

OK Green Ready for operation

SW Green Software-specific

RES Red Agent in reset state

PA Red Power amplifier alarm

Table 20 AGENT: LED Indications

OK SW

RES PA

60 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 39 LIPA: Appearance and Connector Locations

Connector Meaning

TAD Test adapter

CCSLink Server connection via LIPAGE junction box

RX Internal AGENT receiver part connector to IPA / Duplexer

TX Internal AGENT transmitter part connector to IPA / Duplexer

Table 21 AGENT: Connectors

D2-b

D2-a

D1-b

D1-a

GN

D

Server side

Agent side

whiteblackredblackscreen

A50016-G5100-A083-01-7620

61


Id:0900d805800f164a

Antenna Features

The agent may be equipped either with an internal patch antenna (IPA), or with a duplexer for connection to an external antenna.

Figure 40 AGENT: Antenna Connectors

Figure 41 AGENT: Antenna Connection with Internal Patch Antenna

One female SMA connector is the interface for connecting an external TX/RX antenna, if the agent is equipped with a duplexer (DUPLP).

ANT RX ANT TX

INTERNAL PATCH ANTENNA

62 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 42 AGENT: Antenna Connection with Duplexer

ANT TX/RXDUPLEXER

A50016-G5100-A083-01-7620

63


Id:0900d805800f164a

2.11 AGINThe AGIN (Agent Interface) is an overvoltage protection and interface module for the connection of BS-242 AGENTs to the SERVER.

g Not part of BR8.0 and above

Depending on the number of agents installed, one or two agent interface (AGIN) modules are installed (AGIN 0: AGENT 0 .. 11; AGIN 1: AGENT 12 .. 23). For checking the order of the cabling refer to IMN:BTSE BS-242 Pico.

The following pictures show the respective AGIN module versions.

2.11.1 M:AGINV1

Figure 43 AGINV1: Appearance

Types of AGIN

M:AGINV1 S30861-Q2081-X

M:AGINV2 S30861-Q2153-X

M:AGINV3 S30861-Q2183-X

64 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.11.2 M:AGINV2


A50016-G5100-A083-01-7620

65


Id:0900d805800f164a

2.11.3 M:AGINV3


66 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.12 BCOMThe BCOM (Basic Combining Equipment) consists of six identical combining modules (0-5) in a shared case. Each of these modules has the following general functions: Duplexing of the RX and the TX path, to be fed to a common antenna Amplifying and splitting of the RX signal from the antenna to the CUs Coupling of the TX paths from several CUs to the antenna

For the receive path, the BCOM provides a gain of 20 dB +/- 1.5 db (ANT - RX).

There is one LED at the front panel:

Types of BCOM

Basic Combiner 6:6 with 6 antenna interfaces for 6 carriers

BCOMPGV1 S30861-U2338-X P-GSM 900

BCOMDV1 S30861-U2339-X GSM 1800

BCOMPV1 S30861-U2340-X GSM 1900

Basic Combiner 12:6 with 6 antenna interfaces for 12 carriers

BCOM12PGV1 S30861-U2468-X P-GSM 900

BCOM12DV1 S30861-U2469-X GSM 1800

BCOM12PV1 S30861-U2470-X GSM 1900

LED Signal Meaning

POWER Green DC power supply is OK

Table 22 BCOM: LED Indications

A50016-G5100-A083-01-7620

67


Id:0900d805800f164a

2.12.1 BCOMPG/BCOMD/BCOMP

Figure 46 BCOMPG: Appearance

TX-Connector

Antenna Connector

RX-Connector

Powergreen LED

68 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

Figure 47 BCOMP: Appearance

TX-Connector

Antenna Connector

RX-Connector

Powergreen LED

Connector Connected to Module for Cell Configuration 2 / 2 / 2

Assigned Cell Number

ANT 0 Antenna 0 CELL / Sector 0

ANT 1 Antenna 1


ANT 3 Antenna 3

Table 23 BCOM 6:6 Connector Assignment for Cell Configuration 2/2/2

A50016-G5100-A083-01-7620

69


Id:0900d805800f164a


ANT 5 Antenna 5

TX0 CU(0)_TXOUT

BCOM-0_RX0 CU(0)_RX

BCOM-0_RX1 CU(1)_RXDIV CELL 0 (BTS:0)

TX1 CU(1)_TXOUT

BCOM-1 RX0 CU(1)_RX

BCOM-1_RX1 CU(0)_RXDIV

TX2 CU(2)_TXOUT

BCOM-2_RX0 CU(2)_RX


TX3 CU(3)_TXOUT

BCOM-3_RX0 CU(3)_RX


TX4 CU(4)_TXOUT

BCOM-4_RX0 CU(4)_RX


TX5 CU(5)_TXOUT

BCOM-5_RX0 CU(5)_RX


Connector Connected to Module for Cell Configuration 2 / 2 / 2



70 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

2.12.2 BCOM12PGV/BCOM12DV/BCOM12PV

Figure 48 BCOM12: Appearance

A50016-G5100-A083-01-7620

71


Id:0900d805800f164a

Figure 49 BCOM12: Interfaces

Connector Connected to Module for Cell Configuration 6 / 6 / 0 FlexCUs








BCOM-0_TX0 FCU(0)_TX 0 CELL / Sector 0



72 A50016-G5100-A083-01-7620

HWMN:BTSE Modules

Id:0900d805800f164a

Modules

BCOM-0_RX0 FCU(0)_RX A/N0 CELL / Sector 0

BCOM-0_RX1 FCU(1)_RX B/D0 CELL / Sector 0

BCOM-0_RX2 FCU(2)_RX C/N1

BCOM-0_RX3 FCU(0)_RX D/D1

BCOM-1_TX0 FCU(1)_TX 0


BCOM-1_RX0 FCU(1)_RX A/N0


BCOM-1_RX2 FCU(2)_RX B/D0











A50016-G5100-A083-01-7620

73


Id:0900d805800f164a





















Table 24 BCOM 12:6 Connect

hwmnbtsemodules

Documents

system installations

electrical equipment

system installieren

harmful personal interference

radio communications

harmful interference

installation sites

installation instructions