Copyright © 2013 HS Protect I Head Office Geraardsbergsesteenweg 258 9400 Ninove Belgium I info@hsprotect.be Page 1

   

HS PROTECT – EPOX is an air-drying peelable coating designed to protect industrial flooring from damage during construction, transportation and storage. It can easily be applied with an airless spray gun, paintbrush or paint roller.

HS PROTECT – EPOX protects everyone’s interests!

More importantly, HS PROTECT – EPOX protects your customer

relations!

HS PROTECT – EPOX simplifies the maintenance of industrial flooring. The temporary protective coating protects flooring against all types of stains (ink, glue, paint, dirt, etc.) and is easy to remove in one move. After using our product, your floors will be as good as new.

HS PROTECT – EPOX will save you time, money and a lot of problems!

HS PROTECT – EPOX is an extremely tough and durable product. Neither the large number of people walking around on construction sites nor the heavy weight of lifting trucks will damage it. Our product does not contain any solvents, is non-brittle and will not be affected by paint, glue or oil.

A variety of materials that you carefully placed and/or fabricated often requires multiple cleanups after construction.

With HS PROTECT – EPOX this can be avoided!

HS PROTECT – EPOX can be peeled off with one single movement, simultaneously removing all underlying gravel and dirt.

Last but not least, it is important to note that HS PROTECT – EPOX is chemical-free, non-flammable and can be disposed of as regular construction waste.

HS PROTECT – EPOX is a nonskid, safe and cost-effective product!

       

 Copyright © 2013 HS Protect I Head Office Geraardsbergsesteenweg 258 9400 Ninove Belgium I info@hsprotect.be Page 2

   

 

Benefits Overview:

ü water-based, non-flammable and eco-friendly

ü multifunctional product

ü prevents damage

ü can be applied to painted concrete floors and epoxy floors

ü can be applied to stone floors with sealed joints

ü easy to apply/remove

ü eliminates the use of chemical/corrosive cleaning products

Ready in 2 steps: apply and remove

NO MORE BULLSHIT

APPLY REMOVE

21

       

 Copyright © 2013 HS Protect I Head Office Geraardsbergsesteenweg 258 9400 Ninove Belgium I info@hsprotect.be Page 3

   

TECHNICAL DATA SHEET • In General:

HS PROTECT – EPOX is a nonskid water-, alkali- and heatproof product designed specifically for industrial flooring that is excessively walked on.

• Field of Application:

HS PROTECT – EPOX is a revolutionary liquid coating that forms a temporary peelable layer. It is the perfect product for floors surrounded by presses and/or spraying systems or floors on lifting truck routes.

• Specifics:

Appearance Liquid, white (see-through in dry condition)

Fixed Content Approximately 40%

Density 1.05

PH 8

Resistance / Durability HS PROTECT – EPOX is weatherproof and UV-resistant for a maximum period of 12 months outdoors. It will not detach unless removed by peeling.

Drying time HS PROTECT – EPOX will be surface-dry in approximately 30

minutes depending on the weather conditions. It takes 24 hours to completely dry the foil.

Health and safety Nonflammable in both liquid and dry condition.

Local Suction: It is recommended to minimize the molar concentration during spray application.

The use of protective clothing is advised. Avoid skin and eye contact. In case of: CONTACT WITH EYES: Rinse with water for at least 15 minutes.

INHALATION: Inhale fresh air.

       

 Copyright © 2013 HS Protect I Head Office Geraardsbergsesteenweg 258 9400 Ninove Belgium I info@hsprotect.be Page 4

   

CONTACT WITH SKIN: Rinse with water and soap. INGESTION: Remove from stomach by induced vomiting or aspiration. Seek medical attention. RELEASED/SPILLED MATERIAL: Absorb with inert material (e.g. sand, soil, etc.). Caution: Liquid emulsion can be very slippery. WATER DISPOSAL: In accordance with state, local, and federal requirements/measures.

• Application Guidelines:

Application Temperature Between 5°C and 35°C = Ideal temperature.

Manual Application Apply by means of a paint roller. A minimal layer thickness of 200

micron in dry condition, 400 in wet, is recommended. Too thin of a layer will be difficult to remove.

Mechanical Application Apply by means of a spray gun. Avoid spray-mist edges, so that the overall thickness of the layer is not compromised.

Cleaning Equipment can be cleaned with warm water. Add detergent if necessary.

Repairs In case of damage to the HS PROTECT – EPOX film, the film can

easily be replaced by applying a new layer of HS PROTECT –

EPOX above the existing one. The two layers will merge.

Removal The temporary film HS PROTECT – EPOX can easily be removed

with one move. At temperatures below 5 degrees Celsius, the film may

become brittle, which, in turn, will hamper the removal process.

Remarks The freshly applied HS PROTECT – EPOX film should be

protected against rain for a 24-hour period. Once dry, the

HS PROTECT – EPOX film layer becomes thermoplastic.  

       

 Copyright © 2013 HS Protect I Head Office Geraardsbergsesteenweg 258 9400 Ninove Belgium I info@hsprotect.be Page 5

   

• Transport – Packaging – Storage: Store at room temperature in its closed original packaging. Screen from freezing temperatures. Limit open-air exposure to avoid bacterial growth.

Allowed storage: maximum 12 months in non-opened original packaging.

In order to ascertain the suitability of the surfaces to be treated with the HS PROTECT products, the application of the product to a pre-established test area is mandatory. Our company will not be held responsible for damages that may result from

erroneous application of the HS PROTECT products.