hobo rain gauge - iei · hobo rain gauge rg3 data logging rain gauge 0.2 mm rg3-m 0.01 in rg3 15.2...
TRANSCRIPT
Patented technology (U.S. Patent 6,826,664)
HOBO Rain Gauge
RG3 Data LoggingRain Gauge
0.2 mm RG3-M0.01 in RG315.2 cm diameterx 25.7 cm high (6 x 10 in)1.2 kg (2.5 lbs)
Key Advantages (RG3 and RG3-M models):
• Aluminum housing and 15.4 cm (6.06 in.) collector ring • Field-proven design• Logger can be moved into an optional radiation shield for logging air temperature • Three mounting feet to use on flat, level surfaces (three screws included) • Side bracket for mast mounting (hose clamps included) • Self-emptying for continuous rainfall logging
Rainfall Range: Up to 320 cm (RG3-M), up to 160 in (RG3) Resolution: 0.2 mm (RG3-M), 0.01 in (RG3) Time stamp Resolution: 1 second Calibration Accuracy: ±1.0% (up to 20 mm/hr [RG3-M], 1 in/hr [RG3]) Maximum rainfall rate: 12.7 cm (5 in.) per hour
Temperature Range: -20° to 70°C (-4° to 158°F) Accuracy: ±0.47° @ 25°C (±0.85° @ 77°F); a solar radiation shield is required for temperature measurements Resolution: 0.10° @ 25°C (0.18° @ 77°F) Sample rate: 1 second to 18 hours, user-selectable
Memory 16,000 to 23,000 tips when recording rainfall only 25,000 to 30,000 total measurements when recording rainfall and temperature
The HOBO RG3 data logging rain gauge is a self-contained rainfall logger that includes an integrated data logger with a high-quality tipping-bucket rain gauge. The RG3’s logger has a built-in temperature sensor and is on a cable so it can be used in an optional radiation shield for logging air temperature.
Mounting the Rain Gauge
The HOBO Rain Gauge has provisions for mounting two ways: surface mounting (Figure 1) and pole mounting (Figure 2). Surface mounting is recommended where possible. Note: Figure 2 has logger deployed outside of rain gauge housing, mounted inside an optional solar radiation shield.
Optional SolarRadiation Shield
Figure 2: Mast mountingFigure 1: Surface mounting
Ensure top of Rain Gauge is above top of pole
Screws(supplied)
Hose Clamps(supplied)
Data Logger
Software
Pendant®
Communications and Accessories
Tripod/Mast Accessories
HOBOware includes USB interface cable
General Mounting Considerations
• The HOBO Rain Gauge housing MUST be mounted in a LEVEL position.• A clear and unobstructed mounting location is necessary to obtain accurate rainfall readings. Tall objects can interfere with accurate rain measurements. It is recommended that you place the rain gauge away from the obstruction by a distance greater than three times the height of the obstruction If that is not possible, raise the rain gauge as high as possible to avoid shedding.• Avoid splashing and puddles. Be sure the gauge is high enough above any surface that rain will not splash into the top of the collector.• Vibration can significantly degrade accuracy of the tipping bucket mechanism. In windy locations make sure that the bucket will be vibration-free.• For maximum sensitivity in low-moisture environments you can remove the collector screen. This eliminates water retention on the screen which could evaporate before being measured. The tradeoff is that without the screen, debris can get into the funnel and clog the orifice.
HOBO Rain Gauge
Ordering Information
Complete system requires logger, software and base station.
** U-DTW-1 Data Shuttle can be used in place of base station (BASE-U-1)
HOBOware software is available for download via the web.
* Requires HOBOware Pro software
HOBO Rain Gauge RG3 (0.01 in) RG3-M (0.2 mm)
HOBOware Pro Software (Windows/Mac) BHW-PRO-CD Base Station (required) BASE-U-1
HOBO U-Shuttle (requires Base Station)* U-DT-1 HOBO Waterproof Shuttle with Couplers** U-DTW-1 Solar Radiation Shield M-RSA
1.5 Meter Mast M-MPB 2m Tripod with Mast M-TPB 1/4 in Stake Kit M-SKB Guy Wire Kit M-GWA 1/2 in Stake Kit M-SKA