high performance butterfly valves - hattersley · high performance butterfly valves ... to suit...
TRANSCRIPT
Tel: +44 (0)1695 712800 Fax: +44 (0)1695 712820Email: [email protected]
04.06
High Performance Butterfly Valves
SECTION8b
Hattersley-Section 8b 25/4/06 10:59 am Page 1
04.062
Contents and Numerical Index
High Performance Butterfly Valves
Contents Page
Figure Number Index 2Introduction 3Butterfly Valve Data Sheets 4 - 10
In this catalogue we have endeavoured to make the information as accurate aspossible, but we cannot accept any responsibility should it be found that in anyrespect the information is inaccurate or incomplete or becomes so as a result offurther developments.
Numerical Index
Fig No Page
4990 PN16 4, 5, 64990 PN25 7, 84990 PN40 9, 10
Hattersley-Section 8b 25/4/06 10:59 am Page 2
04.06
High Performance Butterfly Valvesfrom Hattersley perfectly complementthe highly specified, superb qualityrubber lined 900 series valves.
Developed for high integrity shut-offand regulation duties where increasedpressure and elevated temperaturespecifications are outside the normaloperating parameters of concentricdisk valves.
With a rugged, fully tapped lug carbonsteel body, the valve is designed fully inaccordance with BS EN 593 with face-to-face dimensions conforming to BSEN 558-1 Basic Series 16 or 20
The Hattersley high performancevalves have enhanced features toprovide impeccable performance andreliability.
Introduction
High Performance Butterfly Valves
Standard Features ■ Carbon steel body with stainless
steel seat■ Stainless steel stem and double
offset disc■ Reinforced PTFE seat■ End of line service up to
full rating■ High Kv values■ Live - loaded gland with Graphite
reinforced PTFE packing
Pressure / Temperature RangeFull pressure ratings are available asstandard - PN16, PN25 and PN40
Temperature capability up to 200ºC
3
Hattersley-Section 8b 25/4/06 10:59 am Page 3
0 40 80 120 160 200 240Temperature ˚C
18
16
14
12
10
8
6
4
2
0
Pre
ssur
e ba
r
Fig. 4990PN16
Steel Fully Lugged Butterfly ValvePN16 - DN 50 to 150
04.064
Material Specification
Specification
Component Material BS EN ASTM
Body Steel 10213-2 GP240GH A216 WCB
Body Seat Stainless Steel 12073 XCrNiMn23-12-2
Disk Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Disk Seal Ring PTFE Reinforced
Retaining Ring Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Stem Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Disk Pin Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Bottom Cap Steel 10028-2 P265GH
Gland Packing PTFE-Graphite
Bearings Bronze-PTFE
Lever
Dimensions
Nominal Size mm 50 65 80 100 125 150
A mm 43 46 46 52 56 56
B mm 123 131 150 175 187 218
H mm 215 215 225 244 260 270
C mm 27 27 27 35 35 42
L mm 265 265 265 265 265 265
Weight kg
B
H
C
A
L
Pressure/Temperature Rating16bar from -10 to 163ºC3.4bar at 204ºC
Test Pressures (Hydraulic)Body: 24 barSeat: 17.6 bar
SpecificationDesigned to BS EN 593Face to face dimensions to BS EN 558-1 basic series 20Reinforced PTFE disk sealStainless steel body seatDouble eccentric disk Bi-directional isolation.Valves are supplied lever operated.Actuator flange ISO 5211/1 To suit flange connections BS 4504PN16, alternative flanges availableWafer pattern available Fig 4985PN16
Hattersley-Section 8b 25/4/06 10:59 am Page 4
04.06 5
0 40 80 120 160 200 240Temperature ˚C
18
16
14
12
10
8
6
4
2
0
Pre
ssur
e ba
r
Fig. 4990GPN16
Steel Fully Lugged Butterfly ValvePN16 - DN 50 to 150
Material Specification
Specification
Component Material BS EN ASTM
Body Steel 10213-2 GP240GH A216 WCB
Body Seat Stainless Steel 12073 XCrNiMn23-12-2
Disk Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Disk Seal Ring PTFE Reinforced
Retaining Ring Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Stem Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Disk Pin Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Bottom Cap Steel 10028-2 P265GH
Gland Packing PTFE-Graphite
Bearings Bronze-PTFE
Gearbox Cast Iron 1561 EN-JL1040 A126 Cl B
Handwheel Steel 10025
Dimensions
Nominal Size mm 50 65 80 100 125 150
A mm 43 46 46 52 56 56
B mm 123 131 150 175 187 218
H mm 215 215 225 244 260 270
C mm 27 27 27 27 27 27
D dia mm 125 200 200 200 200 200
E mm 39 39 39 39 39 39
F mm 152 159 159 159 159 159
Weight kg
F
B
H
D
E
C
A
Pressure/Temperature Rating16bar from -10 to 163ºC3.4bar at 204ºC
Test Pressures (Hydraulic)Body: 24 barSeat: 17.6 bar
SpecificationDesigned to BS EN 593Face to face dimensions to BS EN 558-1 basic series 20Reinforced PTFE disk sealStainless steel body seatDouble eccentric disk Bi-directional isolation.Valves are supplied gear operated.Actuator flange ISO 5211/1To suit flange connections BS 4504PN16, alternative flanges availableWafer pattern available Fig.4985GPN16
Hattersley-Section 8b 25/4/06 10:59 am Page 5
0 40 80 120 160 200 240Temperature ˚C
18
16
14
12
10
8
6
4
2
0
Pre
ssur
e ba
r
Fig. 4990GPN16
Steel Fully Lugged Butterfly ValvePN16 - DN 200 to 600
04.066
Material Specification
Specification
Component Material BS EN ASTM
Body Steel 10213-2 GP240GH A216 WCB
Body Seat Stainless Steel 12073 XCrNiMn23-12-2
Disk Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Disk Seal Ring PTFE Reinforced
Retaining Ring Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Stem Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Disk Pin Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Bottom Cap Steel 10028-2 P265GH
Gland Packing PTFE-Graphite
Bearings Bronze-PTFE
Gearbox Cast Iron 1561 EN-JL1040 A126 Cl B
Handwheel Steel 10025
Dimensions
Nominal Size mm 200 250 300 350 400 450 500 600
A mm 60 68 78 78 102 127 154
B mm 294 333 382 398 448 555 606
H mm 320 366 390 425 440 510 605
C mm 35 42 42 50 50 50 66
D dia mm 300 300 300 457 457 457 610
E mm 52 67 67 90 90 123 138
F mm 197 223 223 279 279 331 477
Weight kg
Pressure/Temperature Rating16bar from -10 to 163ºC3.4bar at 204ºC
Test Pressures (Hydraulic)Body: 24 barSeat: 17.6 bar
SpecificationDesigned to BS EN 593Face to face dimensions to BS EN 558-1 basic series 20Reinforced PTFE disk sealStainless steel body seatDouble eccentric disk Bi-directional isolation.Valves are supplied gear operated.Actuator flange ISO 5211/1To suit flange connections BS 4504PN16, alternative flanges availableWafer pattern available Fig.4985GPN16
F
B
H
D
E
C
A
Hattersley-Section 8b 25/4/06 10:59 am Page 6
04.06 7
0 40 80 120 160 200 240Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
Fig. 4990GPN25
Steel Fully Lugged Butterfly ValvePN25 - DN 50 to 150
Material Specification
Specification
Component Material BS EN ASTM
Body Steel 10213-2 GP240GH A216 WCB
Body Seat Stainless Steel 12073 XCrNiMn23-12-2
Disk Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Disk Seal Ring PTFE Reinforced
Retaining Ring Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Stem Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Disk Pin Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Bottom Cap Steel 10028-2 P265GH
Gland Packing PTFE-Graphite
Bearings Bronze-PTFE
Gearbox Cast Iron 1561 EN-JL1040 A126 Cl B
Handwheel Steel 10025
Dimensions
Nominal Size mm 50 65 80 100 125 150
A mm 43 46 64 64 70 76
B mm 123 131 150 175 187 218
H mm 215 215 220 281 294 317
C mm 27 27 27 35 35 42
D dia mm 125 200 200 250 300 300
E mm 39 39 39 52 52 67
F mm 152 159 159 184 197 223
Weight kg 10 12 17 24 32 47
Pressure/Temperature Rating25bar from -10 to 135ºC20.7bar at 149ºC3.4bar at 204ºC
Test Pressures (Hydraulic)Body: 37.5 barSeat: 27.5 bar
SpecificationDesigned to BS EN 593Face to face dimensions to BS EN 558-1 basic series16Reinforced PTFE disk sealStainless steel body seatDouble eccentric disk Bi-directional isolation.Valves are supplied gear operated.Actuator flange ISO 5211/1To suit flange connections BS EN1092-2 PN25, alternative flangesavailable
F
B
H
D
E
C
A
Hattersley-Section 8b 25/4/06 10:59 am Page 7
0 40 80 120 160 200 240Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
Fig. 4990GPN25
Steel Fully Lugged Butterfly ValvePN25 - DN 200 to 600
04.068
Material Specification
Specification
Component Material BS EN ASTM
Body Steel 10213-2 GP240GH A216 WCB
Body Seat Stainless Steel 12073 XCrNiMn23-12-2
Disk Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Disk Seal Ring PTFE Reinforced
Retaining Ring Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Stem Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Disk Pin Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Bottom Cap Steel 10028-2 P265GH
Gland Packing PTFE-Graphite
Bearings Bronze-PTFE
Gearbox Cast Iron 1561 EN-JL1040 A126 Cl B
Handwheel Steel 10025
Dimensions
Nominal Size mm 200 250 300 350 400 450 500 600
A mm 89 114 114 127 140 152 152 178
B mm 294 333 382 398 448 473 555 606
H mm 369 396 461 477 557 583 643 694
C mm 42 50 50 50 66 66 66 64
D dia mm 300 457 457 457 610 610 610 610
E mm 67 90 123 154 138 138 138 181
F mm 223 279 331 356 477 477 477 598
Weight kg 73 126 167 243 340 454 493 777
Pressure/Temperature Rating25bar from -10 to 135ºC20.7bar at 149ºC3.4bar at 204ºC
Test Pressures (Hydraulic)Body: 37.5 barSeat: 27.5 bar
SpecificationDesigned to BS EN 593Face to face dimensions to BS EN 558-1 basic series16Reinforced PTFE disk sealStainless steel body seatDouble eccentric diskBi-directional isolationValves are supplied gear operatedActuator flange ISO 5211/1To suit flange connections BS EN1092-2 PN25, alternative flangesavailable
F
B
H
D
E
C
A
Hattersley-Section 8b 25/4/06 10:59 am Page 8
904.06
0 40 80 120 160 200 240Temperature ˚C
45
40
35
30
25
20
15
10
5
0
Pre
ssur
e ba
r
Fig. 4990GPN40
Steel Fully Lugged Butterfly ValvePN40 - DN 65 to 150
Material Specification
Specification
Component Material BS EN ASTM
Body Steel 10213-2 GP240GH A216 WCB
Body Seat Stainless Steel 12073 XCrNiMn23-12-2
Disk Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Disk Seal Ring PTFE Reinforced
Retaining Ring Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Stem Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Disk Pin Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Bottom Cap Steel 10028-2 P265GH
Gland Packing PTFE-Graphite
Bearings Bronze-PTFE
Gearbox Cast Iron 1561 EN-JL1040 A126 Cl B
Handwheel Steel 10025
Dimensions
Nominal Size mm 50 65 80 100 125 150
A mm 43 46 64 64 70 76
B mm 123 131 150 175 187 218
H mm 215 215 220 281 294 317
C mm 27 27 27 35 35 42
D dia mm 125 200 200 250 300 300
E mm 39 39 39 52 52 67
F mm 152 159 159 184 197 223
Weight kg 10 12 17 24 32 47
Pressure/Temperature Rating40bar from -10 to 90ºC20.7bar at 149ºC3.4bar at 204ºC
Test Pressures (Hydraulic)Body: 60 barSeat: 44 bar
SpecificationDesigned to BS EN 593Face to face dimensions to BS EN 558-1 basic series16Reinforced PTFE disk sealStainless steel body seatDouble eccentric disk.Bi-directional isolation.Valves are supplied gear operated.Actuator flange ISO 5211/1To suit flange connections BS EN1092-2 PN40, alternative flangesavailable
F
B
H
D
E
C
A
Hattersley-Section 8b 25/4/06 10:59 am Page 9
0 40 80 120 160 200 240Temperature ˚C
45
40
35
30
25
20
15
10
5
0
Pre
ssur
e ba
r
Fig. 4990GPN40
Steel Fully Lugged Butterfly ValvePN40 - DN 200 to 600
04.0610
Material Specification
Specification
Component Material BS EN ASTM
Body Steel 10213-2 GP240GH A216 WCB
Body Seat Stainless Steel 12073 XCrNiMn23-12-2
Disk Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Disk Seal Ring PTFE Reinforced
Retaining Ring Stainless Steel 10088 X5CrNi18-10 A276 Gr304
Stem Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Disk Pin Stainless Steel 10088 X17CrNi16-2 A276 Gr431
Bottom Cap Steel 10028-2 P265GH
Gland Packing PTFE-Graphite
Bearings Bronze-PTFE
Gearbox Cast Iron 1561 EN-JL1040 A126 Cl B
Handwheel Steel 10025
Dimensions
Nominal Size mm 200 250 300 350 400 450 500 600
A mm 89 114 114 127 140 152 152 178
B mm 294 333 382 398 448 473 555 606
H mm 369 396 461 477 557 583 643 694
C mm 42 50 50 50 66 66 66 64
D dia mm 300 457 457 457 610 610 610 610
E mm 67 90 123 154 138 138 138 181
F mm 223 279 331 356 477 477 477 598
Weight kg 79 143 203 288 415 469 589 967
Pressure/Temperature Rating40bar from -10 to 90ºC20.7bar at 149ºC3.4bar at 204ºC
Test Pressures (Hydraulic)Body: 60 barSeat: 44 bar
SpecificationDesigned to BS EN 593Face to face dimensions to BS EN 558-1 basic series16Reinforced PTFE disk sealStainless steel body seatDouble eccentric disk.Bi-directional isolation.Valves are supplied gear operatedActuator flange ISO 5211/1To suit flange connections BS EN1092-2 PN40, alternative flangesavailable
F
B
H
D
E
C
A
Hattersley-Section 8b 25/4/06 10:59 am Page 10