hd cau hinh mot so loai dslam
DESCRIPTION
NoTRANSCRIPT
CÁC BƯỚC CẤU HÌNH MA5303
Bước 1: Console và login vào thiết bị:
Configuration console exit , please press any key to log on
Huawei MA5303 Multi-service Access Module.
Copyright(C) 1998-2004 by Huawei Technologies Co., Ltd.
>>User name:root
>>User password: admin
MA5303>enable
{ <cr>|level-value<U><1,15> }:
MA5303#configure terminal
MA5303(config)#
Bước 2: Xác nhận card:
MA5303(config)#board add 0/1
{EVDA<K>|EADA<K>|EADL<K>|EVDB<K>|BTSB<K>|ESHA<K>|ETHA<K>|EAD
B<K>|EBDL<K>|EADJ<K>|EADK<K> }:EADA ( xác nhận loại card)
Frame 0 slot 1 board add successfully
MA5303(config)#board confirm 0/1
0 frame 1 slot board has been confirmed
Kiểm tra trạng thái card tốt:
MA5303(config)#show board 0/1
------------------------------------I---------------------------
Board Name : EADA
Board state : Normal
Board has ports : 48
Board description: EADA_0_1
---------------------------------------------------------------
Chú ý : MA5303 có 6 card thuê bao, ta sẽ làm tương tự như trên khi tăng số lượng card
sử dụng
Bước 3: Đặt tên node cho thiết bị:
MA5303(config)#hostname MA5303_Mã trạm
MA5303_HNI074(config)#
Bước 4: Active các port ADSL :
MA5303_HNI074(config)#board-adsl X
( giá trị X là slot number của card thuê bao, X = [1 ÷6] )
MA5303_HNI074(config-board-adslX)# activate all
{ <cr>|INTEGER<U><1,109>|name<K> }:
INFO MAJOR 2005-07-02 16:25:48 ALARM NAME : ADSL port status
changed
PARAS INFO : ADSL1/0/0 status changed to activating!
INFO MAJOR 2005-07-02 16:25:48 ALARM NAME : ADSL port status
changed
PARAS INFO : ADSL1/0/1 status changed to activating!
INFO MAJOR 2005-07-02 16:25:49 ALARM NAME : ADSL port status
changed
PARAS INFO : ADSL1/0/2 status changed to activating!
INFO MAJOR 2005-07-02 16:25:49 ALARM NAME : ADSL port status
changed
PARAS INFO : ADSL1/0/3 status changed to activating!
………………………………………………………………………..
INFO MAJOR 2005-07-02 16:26:08 ALARM NAME : ADSL port status
changed
PARAS INFO : ADSL1/0/45 status changed to activating!
INFO MAJOR 2005-07-02 16:26:08 ALARM NAME : ADSL port status
changed
PARAS INFO : ADSL1/0/46 status changed to activating!
INFO MAJOR 2005-07-02 16:26:09 ALARM NAME : ADSL port status
changed
PARAS INFO : ADSL1/0/47 status changed to activating!
( tương tự với các card thuê bao còn lại)
Bước 5: Cấu hình VLAN và PVC cho thuê bao
MA5303(config)#vlan Y to Z
( từ Y tới Z là tất cả các VLAN trong 1 Ring, giá trị này được lấy theo quy hoạch, chú ý
phải gồm tối thiểu 2 Vlan cho port ADSL và VLAN quản lý ).
Please wait.....Done
MA5303(config)#vlan 1233 ( Khai bao Vlan cho quan ly )
MA5303(config)#vlan 233
{ <cr>|to<K> }:
( Ví dụ 233 thuộc khoảng từ Y tới Z và là giá trị VLAN được gán cho DSLAM này)
MA5300(config-vlan233)#vlan-type smart
MA5300(config-vlan233)#svlan-upport GigabitEthernet7/1/0 to GigabitEthernet7/1/1
MA5300(config-vlan233)#svlan-downport adsl 1/0/0 to adsl X/0/47
MA5300(config-vlan233)#switchport adsl X/0/0 to adsl X/0/47
{ <cr>|Ethernet<K>|GigabitEthernet<K>|Adsl<K> }:
( X lần lượt là slot number của card thuê bao, có bao nhiêu card thuê bao thì làm bấy
nhiêu lần )
MA5300(config-vlan233)#exit
MA5300(config)#adsl pvc vpi 8 vci 35 all
MA5300(config)#pitp pmode enable
MA5300(config)#pitp pmode enable adsl 1/0/0 to adsl X/0/47 pvc all
MA5300(config-vlan233)#exit
MA5300(config)#adsl pvc vpi 8 vci 35 all
Bước 5: Tạo PITP
Thuộc tính này nhằm giúp cho BRAS sẽ gửi thông tin về port và VLANid trên DSLAM
cho Radius server.
Thuộc tính này sẽ được thực hiện trên mỗi DSLAM và port downlink của BRAS nối với
DSLAM đó.
Tạo trên DSLAM:
Bật chế độ PITP lên:
MA5300(config)#pitp pmode enable
Gán thuộc tính PITP vào cho các pvc
MA5300(config)#pitp pmode enable adsl 1/0/0 to adsl 1/0/47 pvc all
Tạo trên BRAS:
Xác định downlink port trên BRAS nối với DSLAM
[MA5200G_HNI_1]interface GigabitEthernet 1/0/0.1
[MA5200G_HNI_1-GigabitEthernet1/0/0.1]bas[MA5200G_HNI_1-
GigabitEthernet1/0/0.1-bas]client-option82
Bước 6: Cấu hình port GE
Neu dung cong GE
Port 1 : 7/1/0
MA5300(config)#interface gigabitEthernet 7/1/0
MA5300(config-if-GigabitEthernet7/1/0)#no shutdown
MA5300(config-if-GigabitEthernet7/1/0)#switchport mode trunk
Please wait... Done.
MA5300(config-if-GigabitEthernet7/1/0)#switchport trunk allowed vlan all
Please wait........................................... Done.
MA5300(config-if-GigabitEthernet7/1/0)#switchport trunk allowed vlan 2 to X-1 X+1 to
4000 ( X là smart Vlan cho khách hàng tại DSLAM đó )
Please wait........................................... Done.
MA5300(config-if-GigabitEthernet7/1/0)# speed 1000
MA5300(config-if-GigabitEthernet7/1/0)#duplex full
MA5300(config-if-GigabitEthernet7/1/0)#exit
Port 2 : 7/1/1
MA5300(config)#interface gigabitEthernet 7/1/1
MA5300(config-if-GigabitEthernet7/1/1)#no shutdown
MA5300(config-if-GigabitEthernet7/1/1)#speed 1000
MA5300(config-if-GigabitEthernet7/1/1)#duplex full
MA5300(config-if-GigabitEthernet7/1/1)#switchport mode trunk
Please wait... Done.
MA5300(config-if-GigabitEthernet7/1/1)#switchport trunk allowed vlan all
Please wait........................................... Done.
MA5300(config-if-GigabitEthernet7/1/1)# switchport trunk allowed vlan 2 to X-1 X+1 to
4000 ( X là smart Vlan cho khách hàng tại DSLAM đó )
Please wait........................................... Done.
MA5300(config-if-GigabitEthernet7/1/1)#exit
MA5300(config)#spanning-tree mode stp
MA5300(config)#spanning-tree enable
Neu dung cong ethernet FE
HTY0012A_MA5300(config)#interface ethernet 7/2/0
HTY0012A_MA5300(config-if-Ethernet7/2/0)#duplex full
HTY0012A_MA5300(config-if-Ethernet7/2/0)#speed 100
HTY0012A_MA5300(config-if-Ethernet7/2/0)#switchport mode trunk
Please wait... Done.
HTY0012A_MA5300(config-if-Ethernet7/2/0)#switchport trunk allowed
vlan all
Please wait... Done.
HTY0012A_MA5300(config-if-Ethernet7/2/0)#no shutdown
HTY0012A_MA5300(config-if-Ethernet7/2/0)#
Bước 7 : Cấu hình quản lý NMS
MA5300(config)#interface vlan-interface M
( M là VLAN dành cho quản lý, được xác định theo quy hoạch)
MA5300(config-if-Vlan-interface1233)#ip address 172.16.9.x 255.255.255.0
{ <cr>|secondary<K> }:
(x là giá trị đã được xác định theo quy hoạch cho từng DSLAM)
MA5300(config-if-Vlan-interface1233)#exit
MA5300(config)#snmp-server community public ro
{ <cr>|acl<K> }:
MA5300(config)#snmp-server community private rw
{ <cr>|acl<K> }:
MA5300(config)#snmp-server host 203.113.131.231 version1
MA5300(config)#snmp-server enable traps
{ <cr>|snmp<K> }:
MA5300(config)#ip route 0.0.0.0 0.0.0.0 172.16.9.254
{ <cr>|preference<K>|reject<K>|blackhole<K> }:
Bước 8 : Câu lệnh kiểm tra
MA5300(config)#ping 172.16.9.254
PING 172.16.9.254: 56 data bytes, press CTRL_C to break
Reply from 172.16.9.254: bytes=56 Sequence=0 ttl=254 time = 8 ms
Reply from 172.16.9.254: bytes=56 Sequence=1 ttl=254 time = 9 ms
Reply from 172.16.9.254: bytes=56 Sequence=2 ttl=254 time = 8 ms
Reply from 172.16.9.254: bytes=56 Sequence=3 ttl=254 time = 8 ms
Reply from 172.16.9.254: bytes=56 Sequence=4 ttl=254 time = 8 ms
--- 172.16.9.254 Ping statistics ---
5 packets transmitted
5 packets received
0.00% packet loss
round-trip min/avg/max = 8/8/9 ms
MA5300(config)#show adsl port state adsl
Interface PortState LinkState Line-Profile Alarm-Profile
--------------------------------------------------------------------
Adsl1/0/0 down activating 1 1
Adsl1/0/1 down activating 1 1
Adsl1/0/2 down activating 1 1
Adsl1/0/3 down activating 1 1
Adsl1/0/4 down activating 1 1
Adsl1/0/5 down activating 1 1
Adsl1/0/6 down activating 1 1
Adsl1/0/7 down activating 1 1
Adsl1/0/8 down activating 1 1
Adsl1/0/9 down activating 1 1
Adsl1/0/10 down activating 1 1
Adsl1/0/11 down activating 1 1
Adsl1/0/12 down activating 1 1
Adsl1/0/13 down activating 1 1
Adsl1/0/14 down activating 1 1
Adsl1/0/15 down activating 1 1
Adsl1/0/16 down activating 1 1
Adsl1/0/17 down activating 1 1
Adsl1/0/18 down activating 1 1
Adsl1/0/19 down activating 1 1
Adsl1/0/21 down activating 1 1
Adsl1/0/22 down activating 1 1
Adsl1/0/23 down activating 1 1
Adsl1/0/24 up active 1 1
Adsl1/0/25 down activating 1 1
Adsl1/0/26 down activating 1 1
Adsl1/0/27 down activating 1 1
Adsl1/0/28 down activating 1 1
Adsl1/0/29 down activating 1 1
Adsl1/0/30 down activating 1 1
Adsl1/0/31 down activating 1 1
Adsl1/0/32 down activating 1 1
Adsl1/0/33 down activating 1 1
Adsl1/0/34 down activating 1 1
Adsl1/0/35 down activating 1 1
Adsl1/0/36 down activating 1 1
Adsl1/0/37 down activating 1 1
Adsl1/0/38 down activating 1 1
Adsl1/0/39 down activating 1 1
Adsl1/0/40 down activating 1 1
Adsl1/0/41 down activating 1 1
Adsl1/0/42 down activating 1 1
Adsl1/0/44 down activating 1 1
Adsl1/0/45 down activating 1 1
Adsl1/0/46 down activating 1 1
Adsl1/0/47 down activating 1 1
MA5300(config)#show run ( xem cấu hình running)
Bước 9 : Lưu cấu hình
MA5300(config)#write
The switch configuration will be written to flash.
Are you sure?[Y/N]y
Now writing running configuration to flash memory.
Please wait for a while...
Write running configuration to flash memory successfully.
Chú ý:
Các tham số được bôi đỏ là tham số động sẽ thay đổi theo từng trạm, khi đi config cần
liên hệ trước để lấy thông tin theo đúng quy hoạch.
TÀI LIỆU HƯỚNG DẪN CẤU HÌNH DSLAM MA5605 – HUAWEI
1. PHẦN CỨNG:
- MA5605 là loại DSLAM IP
- MA5605 thuộc dòng MA650x (MA6500; MA6505; và MA6505)
- MA5605 là loại DSLAM có dung lượng nhỏ nhất trong dòng MA650x, với
dung lượng là 4x16 lines = 64 lines
- MA5605 có thể cung cấp các dịch vụ ADSL/ADSL2+/SHDSL
- Cấu trúc của MA6505 gồm:
o 1 card Uplink: làm nhiệm vụ điều khiển hoạt động của toàn DSLAM
và cung cấp giao diện Uplink nối với các thiết bị lớp cao hơn (kết
nối về trung tâm)
o 4 card service: cung cấp giao tiếp với thuê bao.
Cấu trúc phần cứng:
Card điều khiển – MFEB:
STT Tên ICON Chức năng
1 CON Cổng console – dùng để cấu hình thiết bị với quyền cao nhất.
2 100Base-Tx Là cổng Fast Ethernet (100Mbps) giao diện điệndùng để kết nối
uplink cho DSLAM về trung tâm
3 100Base-Fx-C
Là cổng Fast Ethernet (100Mbps) giao diện quang dùng để kết nối
với DSLAM đứng sau nó (theo mô hình đấu cascading, tuy nhiên
Viettel sẽ không sử dụng mô hình này).
4 RUN Là đèn (màu xanh lá) báo trạng thái hoạt động của DSLAM. Nếu
đèn sáng nháy báo hiệu card đang hoạt động tốt.
5 ALM Là đèn (màu đỏ) báo trạng thái cảnh báo lỗi của DSLAM. Khi có
lỗi xảy ra đối với thiết bị thì đèn sáng đỏ.
6 RESET Là nút reset bằng tay đối với thiết bị.
Lưu ý:
- Port 100Base-Tx chỉ sử dụng làm uplink port
- Port 100Base-Fx-C chỉ sử dụng để đấu cascade với các DSLAM nối sau nó,
không làm port uplink được do vậy topo đối với các DSLAM MA5605
chỉ có thể là đấu hình star nối các MA5605 về IP switch hoặc cascade theo
đúng chức năng của từng cổng.
Card thuê bao – ADCE:
STT Tên ICON Chức năng
4 RUN
Đèn RUN sáng nhấp nhay màu xanh lá (nhịp nhấp nháy
đồng bộ với nhịp nhấp nháy trên đèn RUN của card điều
khiển) chỉ báo card đang hoạt động ở trạng thái tốt.
5
Giao diện
với cáp
thuê bao
Kết nối tới khách hàng và kết nối tới tổng đài điện thoại
6 Card thuê
bao ADCE
- Là loại card thuê bao cung cấp được các dịch vụ
ADSL2+/ADSL
- Card thuê bao ADCE đã bao gồm cả phần phối thoại
trên cùng một card (Built-in splitter).
- Mỗi card cung cấp được 16 lines ADSL2+/ADSL
thường
MÔ HÌNH ĐẤU NỐI MẠNG ADSL VỚI MA5605
MA5605
MA5605
FE (giao
diện điện)
FE (giao
diện điện)
Switch
SDH
BRAS
MA5605Coverter O/E
MA5605
Coverter O/E
FE (giao
diện điện)
2. CÁC BƯỚC CẤU HÌNH
Kết nối console:
Mở phần mềm cấu hình DSLAM:
Đăng nhập dưới user/pass sau: Username: root
Password: admin
MA5605>enable
MA5605#configure terminal
MA5605(config)#
Khai địa chỉ IP cho thiết bị:
MA5605(config)#atmlan ip-address ethernet A.B.C.D 255.255.255.0
A.B.C.D: lấy theo quy hoạch
Permit dải IP để telnet vào thiết bị:
MA5605(config)#atmlan ip-access 203.113.131.1 203.113.131.254 255.255.255.0
MA5605(config)#atmlan ip-access 203.113.128.1 203.113.128.254 255.255.255.0
MA5605(config)#atmlan ip-access 203.113.129.1 203.113.129.254 255.255.255.0
MA5605(config)#atmlan ip-access 220.231.122.1 220.231.122.31 255.255.255.0
MA5605(config)#atmlan ip-access 172.16.0.1 172.16.254.254 255.255.0.0
Cấu hình Ip route:
MA5605(config)#atmlan ip-route 0.0.0.0 0.0.0.0 A1.B1.C1.D1
A1.B1.C1.D1: lấy theo quy hoạch: default gateway
Cấu hình Vlan quản lý:
MA5605(config)#nms VLANID
VLANID lấy theo quy hoạch
MA5605(config)#snmp-server community root 203.113.131.70 public private
notify 162 v1
MA5605(config)#snmp-server enable agent all
MA5605(config)#snmp-server enable traps
Đổi tên thiết bị
MA5605(config)#hostname NAME
NAME: theo quy hoạch
Xác nhận card
(Ở viettel mua card ADCE với mã trên tem card là H523, nếu card khác thì nhờ kĩ
thuật tỉnh đọc ở góc dưới card)
MA5605(config)#board add adsl H523 adce 0/slot
H523 adce: loại card và mã card
Cấu hình cho khách hàng :
MA5605(config)#interface lan 0/0
MA5605(config-lan0/0)# port mode tagged negotiate
MA5605(config-lan0/0)#vlan VLANIDcustomer common
VLANIDcustomer: lấy theo quy hoạch
MA5605(config-lan0/0)#pitp switch pmode
Nếu đằng sau có thiết bị nào nối đuôi cần khai thêm:
MA5605(config-lan0/0)#cascade forward vlan VLANID (vlan quản lý
đằng sau)
MA5605(config-lan0/0)#cascade forward vlan VLANID (vlan khách hàng
đằng sau)
Cấu hình traffic-profile:
MA5605(config)# traffic-profile 4096 4
MA5605(config)# traffic-profile 640 5
MA5605(config)#pvc lan 0/0 VLANIDcustomer 5 disable adsl 0/1/1 8 35 off off 4
5
(tạo toàn bộ cho các port như scrips đi kèm )
Tạo adsl line profile:
MA5605(config)#adsl line-profile add 4
(phần sau này phải enter mới hiện ra các thông số để chọn, chú ý chọn ADSL2+
và để tốc độ down 4096 – 32 và up 640 – 32)
MA5605(config)# interface adsl 0/1
MA5605(config-adsl-0/1)# deactivate all
MA5605(config-ADSL-0/1)#activate all 4
Save cấu hình:
MA5605(config)#save
Script cau hinh cac card
Card1
pvc lan 0/0 1152 5 disable adsl 0/1/1 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/2 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/3 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/4 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/5 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/6 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/7 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/8 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/9 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/10 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/11 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/12 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/13 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/14 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/15 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/1/16 8 35 off off 4 5
Card 2
pvc lan 0/0 1152 5 disable adsl 0/2/1 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/2 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/3 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/4 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/5 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/6 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/7 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/8 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/9 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/10 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/11 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/12 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/13 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/14 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/15 8 35 off off 4 5
pvc lan 0/0 1152 5 disable adsl 0/2/16 8 35 off off 4 5
Card 3
pvc lan 0/0 1160 5 disable adsl 0/3/1 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/2 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/3 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/4 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/5 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/6 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/7 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/8 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/9 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/10 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/11 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/12 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/13 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/14 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/15 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/3/16 8 35 off off 4 5
Card 4
pvc lan 0/0 1160 5 disable adsl 0/4/1 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/2 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/3 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/4 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/5 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/6 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/7 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/8 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/9 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/10 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/11 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/12 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/13 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/14 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/15 8 35 off off 4 5
pvc lan 0/0 1160 5 disable adsl 0/4/16 8 35 off off 4 5
CÁC BƯỚC CẤU HÌNH DSLAM CỦA ZTE
(FSAP 9800&9803)
Bước1 : Console và login vào thiết bị
Để cấu hình lại DSLAM, xoá cấu hình trước đây, thực hiện lệnh sau:
# erase config
#yes
# reboot
#yes
.....
Sau đó thực hiện config thiết bị từ đầu:
######################################################################
# #
# Welcome to ZTE Full Service Access Platform #
# #
# Press Return to get started #
# #
# Copyright 2005-2009 , ZTE Co.,Ltd. #
# #
######################################################################
Login: admin
Password: admin
# enable
Please input password: admin
Lưu ý : PW mặc định hiện tại là : admin, nhưng có thể thay đổi PW cho DSLAM
bằng lệnh sau:
# change pass
# user modify
fsap>user modify
Please input your password:
Do you need modify your username: yes[Y] or no[N] [N]y
Please input new username(len<=15): [abc]admin
Do you need modify your password: yes[Y] or no[N] [N]y
Please input new password(len<=15):ztezte
Please input new password again:ztezte
Ví dụ: user : admin
Password : ztezte
Bước 2: Add card mới
a. Thêm card ( khi không có card splitter)
Fsap# add-card ASNVB 2 splitter-shelf
Fsap# add-card ASNVB 3 splitter-shelf
Fsap# add-card ASNVB 4 splitter-shelf
Lưu ý : Để xoá 1 board nói chung có thể dùng lệnh :
# del-card 6
Để xoá 1 card con tại board CSC, có thể dùng lệnh
# del-subcard CSC (xoá card điều khiển)
b. Add card điều khiển CSC
fsap# add-subcard csc upside noNE underside sgfb
Bước 3: Cấu hình Uplink port
fsap# config
fsap(config)# inter gigabit-ethernet 9/5
fsap(cfg-if-ge-9/5)# speed 1000
fsap(cfg-if-ge-9/5)# duplex full
fsap(cfg-if-ge-9/5)# no shutdown
fsap(cfg-if-ge-9/5)# exit
fsap(config)#
fsap(config)# inter gigabit-ethernet 9/6
fsap(cfg-if-ge-9/6)# speed 1000
fsap(cfg-if-ge-9/6)# duplex full
fsap(cfg-if-ge-9/6)# no shutdown
fsap(cfg-if-ge-9/6)# exit
fsap(config)#
Bước 3a. Add các vlan cho dslam ZTE ( Vlan cho user và khách hàng )
fsap(config)# add-vlan 260 ( 260 La vlan quan ly cua trạm đó)
fsap(config)# add-vlan 860 ( 860 La vlan khach hàng cua trạm đó)
Bước 4: Gán Vlan lên cổng Uplink 5 và 6.
fsap(config)# vlan 260 9/5-6 tag
fsap(config# vlan 860 9/5-6 tag
Bước 5: Khai báo địa chỉ IP in-band
fsap(config# ip subnet 172.16.167.11 255.255.255.0 260
Bước 6: Khai báo địa chỉ IP của NM Server
fsap(config# snmp-server host 203.113.131.231
Bước 7: Khai báo route tĩnh.
fsap(config# ip route 0.0.0.0 0.0.0.0 172.16.167.1
Bước 8: Cấu hình dịch vụ
a. Thêm port cho VLAN dịch vụ.
# vlan 860 2-4/1-64 untag ( Gán vlan cho các cổng thuê bao của card 2,
3,4)
b. Khai báo pvid của port là VLAN ID dịch vụ
Ở đây ta khai báo cho 3 board dịch vụ, tương ứng với 3 slot 2.3,4
fsap(config# # slot adsl 2
# pvid 860 pvc 1
# atm pvc 1 vpi 8 vci 35
# exit
# slot adsl 3
# pvid 860 pvc 1
# atm pvc 1 vpi 8 vci 35
# exit
# slot adsl 4
# pvid 860 pvc 1
# atm pvc 1 vpi 8 vci 35
# exit
c. Chống broadcast trong mạng.
# slot ethernet 9
# up-link 5-6
d. Khai báo Profile
# adsl-profile viettel1
# adsl-profile viettel
AtucConfRateMode(1-fixed,2-adaptAtStartup,3-adaptAtRuntime):[2]
AtucConfRateChanRatio(0..100):[100]
AtucConfTargetSnrMgn(0..310(0.1dB)):[80]
AtucConfMaxSnrMgn(80..310(0.1dB)):[310]
AtucConfMinSnrMgn(0..80(0.1dB)):[0]
AtucConfDownshiftSnrMgn(0..310):[40]
AtucConfUpshiftSnrMgn(0..310):[120]
AtucConfMinUpshiftTime(0..16383):[30]
AtucConfMinDownshiftTime(0..16383):[30]
ConfProfileLineType(1-fast-only ,2-interleaved-only):[2]
AtucChanConfFastMaxTxRate(0..102400kbps):[1024]512
AtucChanConfFastMinTxRate(0..512kbps):[0]
AtucChanConfInterleaveMaxTxRate(0..102400kbps):[1024]512
AtucChanConfInterleaveMinTxRate(0..512kbps):[0]
AtucChanConfMaxInterleaveDelay(0..255ms):[16]
AturConfRateMode(1-fixed,2-adaptAtStartup,3-adaptAtRuntime):[2]
AturConfRateChanRatio(0..100):[100]
AturConfTargetSnrMgn(0..310(0.1dB)):[80]
AturConfMaxSnrMgn(80..310(0.1dB)):[310]
AturConfMinSnrMgn(0..80(0.1dB)):[0]
AturConfDownshiftSnrMgn(0..310(0.1dB)):[40]
AturConfUpshiftSnrMgn(0..310(0.1dB)):[120]
AturConfMinUpshiftTime(0..16383):[30]
AturConfMinDownshiftTime(0..16383):[30]
AturChanConfFastMaxTxRate(0..10240kbps):[512]
AturChanConfFastMinTxRate(0..512kbps):[0]
AturChanConfInterleaveMaxTxRate(0..10240kbps):[512]
AturChanConfInterleaveMinTxRate(0..512kbps):[0]
AturChanConfMaxInterleaveDelay(0..255ms):[16]
AtucDMTConfFreqBinsOperType(1-open,2-close,3-cancel):[3]
AturDMTConfFreqBinsOperType(1-open,2-close,3-cancel):[3]
LineDMTConfEOC(1-byte ,2-streaming ):[1]
LineDMTConfTrellis(1-on,2-off):[1]
AtucConfMaxBitsPerBin(0..15):[15]
AtucConfTxStartBin(6..511):[32]
AtucConfTxEndBin(32..511):[511]
AtucConfRxStartBin(6.0.63):[6]
AtucConfRxEndBin(6..63):[31]
AtucConfUseCustomBins(1-on,2-off):[2]
AtucConfDnBitSwap(1-on,2-off):[1]
AtucConfUpBitSwap(1-on,2-off):[2]
AtucConfREADSL2Enable(1-on,2-off):[2]
AtucConfPsdMaskType(1-DMT_PSD_MSK,2-ADSL2_PSD_MSK,3-
ADSL2_READSL_WIDE_PSD_MSK,4-ADSL2_READSL_NARROW_PSD_MSK):[2]
AtucConfPMMode(1-DISABLE,2-L2_ENABLE,3-L3_ENABLE,4-L3_ENABLE |
L2_ENABLE):[3]
AtucConfPML0Time(0..255s):[240]
AtucConfPML2Time(0..255s):[120]
AtucConfPML2ATPR(0..31db):[3]
AtucConfPML2Rate(512..1024kbps):[512]
Press M or m key to modify, or the other key to complete?[C]
- Khai báo cho từng board ( ở đây là các board 2,3,4)
# slot adsl 2
# pppoe-plus enable
# adsl profile viettel
# slot adsl 3
# pppoe-plus enable
# adsl profile viettel
# slot adsl 4
# pppoe-plus enable
# adsl profile viettel
Bước 9: Khai báo xác định điểm truy nhập và PPPoe
# port-location access-node-identify hostname ??
# port-location pppoe-plus enable
Bước 10: Khai báo STP
# spanning-tree classic-stp enable
#configure interface gigabit-ethernet 9/5
#spanning-tree enable
#exit
#configure interface gigabit-ethernet 9/6
#spanning-tree enable
#exit
Bước 11: Save cấu hình
# Save
..................
HƯỚNG DẪN CẤU HÌNH DSLAM ZyXEL IES1000
I.Mô hình đấu nối.
DSLAM ZyXEL IES hỗ trợ giao diện uplink Ethernet. Do nhu cầu triển khai
DSLAM này cho các Huyện xa nên mỗi một DSLAM được đi kèm một cặp
converter chuyển luồng E1 sang FE.
Sơ đồ đấu nối thiết bị DSLAM lên Switch:
SDH
Converter
DSLAM ZyXEL
IES1000
Converter
SWITCH ZTE
FE
FE
FE
FE
E1
E1
II.Các bước cấu hình sử dụng command line.
Bước 1: Console vào thiết bị.
1. Dùng Hyper Terminal để console vào thiết bị.
Console vào thiết bị sử dụng Hyper Terminal với:
Bits rate: 9600 bps
Data bit: 8
Pảity: none
Stop bit: 1
Flow controle: none
Chọn Restore Defaults để đặt lại thông tin của Hyper.
2. Telnet vào thiết bị.
Telnet vào thiết để cấu hình theo địa chỉ IP:
IP: 192.168.1.1
Mask: 255.255.255.0
Default Gateway: 192.168.1.254
3. Account đăng nhập.
Đăng nhập vào thiết bị theo account admin:
Username: admin
Password: 1234
Copyright (c) 1994 - 2006 ZyXEL Communications Corp.
Bước 2: Cấu hình thông tin system.
1. Đặt hostname cho thiết bị.
- Câu lệnh: ZyXEL_IES1000> sys info hostname <Hostname>
<Hostname>: Được đặt theo quy hoạch chuẩn.
- Lệnh: ZyXEL_IES1000> sys info hostname HNI0138A_IES1K
HNI0138A_IES1K> - Kiểm tra thông tin cấu hình:
HNI0138A_IES1K> sys info show
Hostname: HNI0138A_IES1K
Location:
Contact:
Model: AAM1212-51
ZyNOS version: V3.52(ABA.0) | 07/19/2006
F/W size: 2748104
MAC address: 00:19:CB:38:99:63
System up time: 0(days) : 22:44:01
Bootbase version: V1.03(AAM1212-51) | 02/18/2005
F/W build date: Jul 18 2006 15:48:00
DSP code version: 6.04.0003
Hardware version: B0B
Serial number: 0Z0707033093
HNI0138A_IES1K>
2. Tạo account và phân quyền.
Tạo các account truy nhập vào DSLAM và phân quyền cho account truy
nhập vào hệ thống.
- Câu lệnh: sys user set <username> <password> <high|middle|low>
<hinh|middle|low>: 3 quyền truy nhập của account
High: Mức cho phép toàn quyền cấu hình thiết bị
Middle: Mức cho phép cấu hình mức giới hạn, không cho phép
quyền xóa các account.
Low: Mức thấp nhất chỉ cho phép thực hiện các lệnh show cấu
hình.
- Lệnh: HNI0138A_IES1K> sys user set anhln 1234 high
- Kiểm tra thông tin account: HNI0138A_IES1K> sys user show
auth mode: landr
radius server ip: 127.0.0.254 port: 1812
radius server secret: 1234
default user privilege: low
index status name privilege
----- ------ ------------------------------- ---------
1 V admin high
2 V anhln high
3. Thiết lập thời gian hệ thống.
Thiết bị được cấu hình thời gian cho hệ thống để phụcvụ quá trình phân tích
log và phần tích cước cho user.
- Câu lệnh:
Set time: sys time set <hh> [<mm> [ss]]
Set date: sys date set <yyyy> <mm> <dd>
- Lệnh: HNI0138A_IES1K> sys time set 09 40 00
HNI0138A_IES1K> sys date set 2007 11 15
- Kiểm tra thông tin: HNI0138A_IES1K> sys time show
current time is 09:41:01
HNI0138A_IES1K> sys date show
current date is Thu 2007/11/15
HNI0138A_IES1K>
Bước 3: Cấu hình cổng Ethernet Uplink.
Thiết bị sử dụng giao diện đường FE 100M. Thiết bị sử dụng 2 ports
Ethernet dùng uplink. Thông tin cấu hình:
Enable: enable port enet
Speed: đặt tốc độ cho port (default auto)
Name: đặt name cho port.
Lệnh:
HNI0138A_IES1K> switch enet enable enet1,enet2 //enable port
HNI0138A_IES1K> switch enet name enet2 UPLINK //dat ten port
enet2
HNI0138A_IES1K> switch enet speed enet2 100copper //set speed 100M
Kiểm tra thông tin cấu hình port(enet2): HNI0138A_IES1K> switch enet show
port mode name
----- ---------------- -------------------------------
enet1 auto enet1
enet2 100copper UPLINK
HNI0138A_IES1K>
Bước 4: Cấu hình Vlan.
- Add vlan: Tạo vlan nms và vlan user cho DSLAM. Cấu trúc lệnh:
switch vlan set <Vlanid> <portlist>:<F|<T|U>|X|N> <name>
switch vlan enable <vlanid>
Trong đó:
<vlanid>: vlan cần tạo
<portlist>: danh sách port gán vlan đó vào
F(Fixed): Cố định vlan
X(forbidden):
N(Normal): vlan thông thường
U(Untag): Sử dụng untag vlan ~ Untag trong Fsap9800
T(Tag): Sử dụng tag vlan ~ tag trong Fsap9800
Lệnh:
HNI0138A_IES1K> switch vlan set 20 enet1,enet2:FT //Vlan nms luon
la Tag
HNI0138A_IES1K> switch vlan enable 20
HNI0138A_IES1K> switch vlan set 1039 enet1,enet2:FT //Vlan kh/hang
tren uplink cung luon la Tag
HNI0138A_IES1K> switch vlan set 1039 1~12:FU //Vlan Kh/hang tren
port thue bao luon la Untag
HNI0138A_IES1K> switch vlan enable 1039
- Xóa vlan:
Lệnh:
HNI0138A_IES1K> switch vlan delete <vlanlist>
- Gán vlan cho host: Gán vlan nms cho thiết bị.
Lệnh: switch vlan cpu set <vlanid> HNI0138A_IES1K> switch vlan cpu set 20
- Kiểm tra thông tin vlan: HNI0138A_IES1K> switch vlan show 20,1039
vid name F:fixed X:forbidden N:normal U:untag T:tag
---- ------------------------------- -------------------------------------------
20 -
enabled 123456789012 12
FFFFFFFFFFFF FF
UUUUUUUUUUUU TT
1039 -
enabled 123456789012 12
FFFFFFFFFFFF FF
UUUUUUUUUUUU TT
HNI0138A_IES1K>
Bước 5: Cấu hình IP và Route.
- Đặt ip cho DSLAM:
Lệnh: ip set <ip>[/netmask]
HNI0138A_IES1K> ip set 172.16.161.30/24
- Đặt gateway cho DSLAM:
Lệnh: ip gateway set <ip-gateway>
HNI0138A_IES1K> ip gateway 172.16.161.1 HNI0138A_IES1K> ip show
interface ip netmask
--------- --------------- ---------------
Ethernet 172.16.161.30 255.255.255.0
default gateway: 172.16.161.1 - Đặt ip route cho DSLAM:
Lệnh: ip route set <dst ip>[/netmask] <gateway ip> <metric> <name>
Or: : ip route set default <gateway ip> <metric> HNI0138A_IES1K>ip route set default 172.16.161.11 HNI0138A_IES1K>ip route show
index dest gateway metric name
----- ------------------ --------------- ------ -------------------------------
1 172.16.161.0/24 172.16.161.30 1
2 default 172.16.161.1 1
Bước 6: Tạo adsl line-profile ~ tao profile trong Fsap 9800
- Tạo profile:
Lệnh: adsl profile set <profile> <fast|interleave[=<up delay>,<down delay>]>
<up max rate> <down max rate>
[<up target margin> <up min margin> <up max margin> <up min rate>
<down target margin> <down min margin> <down max margin> <down min
rate>
<up down-shift margin> <up up-shift margin>
<down down-shift margin> <down up-shift margin>]
Vd: adsl profile set NETPLUS fast 640 4096 6 0 31 32 6 0 31 32 3 9 3 9 chọn
mode
fast
Up max
Up min
Down max
Down min
hoặc adsl profile set NETPLUS interleave 640 4096 6 0 31 32 6 0 31 32 3 9 3 9
chọn mode interleave, interleave delay sẽ lấy default là 20 ms.
Trong đó:
<profile>: tên profile ( Lưu ý ko có dấu: +, =,...)
Chỉ thay đổi các thông số về tốc độ max/min của upstream và downstream,
còn các thông số khác giữ nguyên.
Bước 7: Cấu hình Port ADSL. ~ set profile cho port chu y # vcprofile
- Bật các ports adsl:
Lệnh: adsl enable <portlist>
ZyXEL_IES1000> adsl enable 1~12
- Gán profile vừa tạo vào các port adsl:
Lệnh: adsl profile map <portlist> <profile>
<glite|gdmt|t1413|auto|adsl2|adsl2+>
Vd: adsl profile map 1~12 NETPLUS auto
Xem thông tin profile của các port vừa tạo:
HNI0138A_IES1K> adsl show
port enable mode up/downstream profile
---- ------ -------- ------------- --------------------
1 V auto 640/ 4096 NETPLUS
2 V auto 640/ 4096 NETPLUS
3 V auto 640/ 4096 NETPLUS
4 V auto 640/ 4096 NETPLUS
5 V auto 640/ 4096 NETPLUS
6 V auto 640/ 4096 NETPLUS
7 V auto 640/ 4096 NETPLUS
8 V auto 640/ 4096 NETPLUS
9 V auto 640/ 4096 NETPLUS
10 V auto 640/ 4096 NETPLUS
11 V auto 640/ 4096 NETPLUS
12 V auto 640/ 4096 NETPLUS
- Gán pvc cho các port adsl: ~ pvc atm vpi 8 vci 35 trong Fsap9800
Lệnh: adsl pvc set <portlist> <vpi> <vci> <super |vid = 1..4094
<priority>> <DS vcprofile[,US vcprofile]>
Trong đó:
<portlist>: danh sách các port.
<vpi>: tham số vpi (viettel la 8)
<vci>: tham số vci (viettel la 35)
<vid>: vlan id ~ vlan kh/hang
<priority>: 0 (để mặc định)
<DS profile>: VC Profile Download stream chọn DEFVAL vì VC
profile này đóng gói theo llc
<US profile>: VC Profile Upload stram chọn DEFVAL
Trong dslam có 2 VC profile default là:DEFVAL, DEFVAL_MAX.
Xem thông tin của VC profile như sau:
HNI0138A_IES1K>adsl vcprofile show
profile encap class aal pcr cdvt scr bt
------------------------------- ----- -------- ---- ------ ---- ------ ---
DEFVAL llc ubr aal5 300000 0 0 0
DEFVAL_VC vc ubr aal5 300000 0 0 0
Cấu hình: HNI0138A_IES1K> adsl pvc set 1~12 8 35 871 0 DEFVAL, DEFVAL
HNI0138A_IES1K> adsl pvc show
port vpi vci pvid priority DS/US vcprofile
---- --- ----- ---- -------- --------------------------------------------
1 8 35 1039 0 DEFVAL/DEFVAL
2 8 35 1039 0 DEFVAL/DEFVAL
3 8 35 1039 0 DEFVAL/DEFVAL
4 8 35 1039 0 DEFVAL/DEFVAL
5 8 35 1039 0 DEFVAL/DEFVAL
6 8 35 1039 0 DEFVAL/DEFVAL
7 8 35 1039 0 DEFVAL/DEFVAL
8 8 35 1039 0 DEFVAL/DEFVAL
9 8 35 1039 0 DEFVAL/DEFVAL
10 8 35 1039 0 DEFVAL/DEFVAL
11 8 35 1039 0 DEFVAL/DEFVAL
12 8 35 1039 0 DEFVAL/DEFVAL
Chu y: sau lenh tren ta thuc hien lenh adsl pvc show ket qua se khac tren khi
co them chi so vpi 0 vci 33. ta phai thuc hien lenh
> adsl pvc delete 1~12 0 33
Bước 8: Đặt Access-list
Lệnh: sys client set <index> <start ip> <end ip> [[telnet] [ftp] [web] [icmp]]
Sys client ena <index>
Vd:
HNI0138A_IES1K> sys client set 1 172.16.0.0 172.16.255.255 telnet ftp web icmp
HNI0138 sys client set 2 203.113.188.0 203.113.188.255 telnet ftp web icmp
mp
HNI0138A_I sys client set 3 203.113.131.0 203.113.131.255 telnet ftp web icmp
mp
> sys client set 4 203.113.151.136 203.113.151.143 telnet ftp web icmp
icmp
HNI0138A_IES1K> sys client set 5 192.168.0.0 192.168.1.1 telnet ftp web icmp
HNI0138A_IES1K> sys client ena 1
HNI0138A_IES1K> sys client ena 2
HNI0138A_IES1K> sys client ena 3
HNI0138A_IES1K> sys client ena 4
HNI0138A_IES1K> sys client ena 5
Bước 9: Save cấu hình.
HNI0138A_IES1K> config save
generating configuration...
saving configuration to flash...
Bước 10: Kiểm tra thông tin cấu hình.
Để kiểm tra thông tin cấu hình cho DSLAM ZyXEL IES1000 ta sử dung các
lênh show tưng mục trong cấu hình.
Câu lệnh: config show <sys|sw|adsl|ip|stat|all>
statistics adsl linedata 1~12 -> xem trang thai port sau khi cau hinh
Hướng dẫn tích hợp DSLAM ECI M41
I. Hướng dẫn lắp đặt thiết bị.
CCP NI Card NI HFI CPU 1,2 Spliter Card Line
Card FAN
Hi-FOCuS M41 bao gồm một shelf, các module và một lắp. Được hỗ trợ cắm các
module bao gồm:
- Card NI( card điều khiển) cắm vào NI slot.
- Card thê bao ATUC64 cắm vào slot 1,3.
- Card phối thoại SC64 cắm vào slot 2,4.
- Card CCP(Central Connection Panel).
- Module Power A, B.
- Central Filtering Unit (CFU) A and CFU B cards module
- FAN Module
- Remote Line Powering (RLP) module (replacing the HIF power feed and CFU
cardsmodules)
Các thông số cơ bản của M41:
- Height: 200 mm (7.9”)
- Width: 500 mm (19.7”)
- Depth: 280 mm (11.0”)
- Weight: 12 kg (26.5 lbs)
- Weight with cards: 17 kg (37.5lbs)
- Operating Power: -48 VDC source nominal (-40.5 VDC to 75 VDC), dual feed
Vì chiểu rộng của M41 la 19.7” nên không lắp vừa vào rack 19” thông thường. Vì vậy,
việc lắp đặt vào rack 19” theo sơ đồ như sau:
II. Hướng dẫn Cosole vào thiết bị.
1. Console:
Hi-FOCuS M41 hỗ trợ console vào thiết bị theo cổng COM (RS-232). Việc console vào
thiết bị để cấu hình uplink về switch và sử dụng OPS để cấu hình các dịch vụ ADSL cho
M41. Các bước để console vào thiết bị:
Console vào thiết bị theo cổng COM(RS-232):
Sử dụng cáp console 2 cổng RS-232 (đực và cái) và dùng phần mềm Hyper Terminal để
console vào M41 với các thông số cho cổng COM sau:
• Bit per second: 57600
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
Login vào thiết bị theo username và password mặc định như sau:
Username: ecidslam
Password: Hi-FOCuS
2. Telnet:
M41 hỗ trợ telnet vào thiết bị bằng cổng outband. Dùng cáp mạng được bắn chéo để
telnet vào thiết bị. Cắm cáp mạng vào cổng Ethernet1.
Trên M41 IP Outband được đặt mặc định là:
IP: 192.168.20.1
Subnet: 255.255.255.0
GW: 192.168.20.10
Vì thế chỉ việc đặt IP của máy tính cùng dải IP của M41 ta có thể telnet vào thiết bị theo
ip trên.
Ví dụ: Đặt ip của máy tính là:
IP: 192.168.20.2
Subnet: 255.255.255.0
GW: (không cần thiết đặt)
III. Hướng dẫn cấu hình thiết bị.
Để cấu hình DSLAM M41 được cấu hình bằng CLI và cấu hình bằng OPS. Các bước cấu
hình M41.
A. Cấu hình bằng lệnh:
1. Dùng Ethernet cable hoặc Console cable kết nối vào DSLAM.
2. Enable hai port IPNI dùng để quản lý In-band
sportconf a 1 2 1
a IPNI slot 17
1 Port number
1 Port number để quản lý In-band
1 Enable (2: Disable)
sportconf a 2 2 1
3. Thiết lập VLAN cho quản lý In-band
sinvlan vlanid 0
vlanid Lấy theo quy hoạch
4. Thiết lập IP address cho quản lý In-band
inbandip ip_address defaul_tgateway netmask/subnetmask
ip_address Theo quy hoạch
default_gateway Theo quy hoạch
netmask/subnetmask Theo quy hoạch
5. Thiết lập Default gateway
dgateway default_gateway
default_gateway Theo quy hoạch, giống địa chỉ câu trên
6. Enable full duplex trên 2 port của IPNI card
sportconf a 1 4 2
a IPNI slot 17
1 Port 1
4 trạng thái full duplex
2 enable
sportconf a 2 4 2
7. Disable Automatic Laser Shutdown trên 2 port của card IPNI
sportconf a 1 9 2
sportconf a 2 9 2
1 Port 1 trên card IPNI
2 Port 2 trên card IPNI
8. Aggregating 2 port trên của card IPNI
exec sw_port2portEnable (20,22)
9. Khai báo ACL
Kiểm tra IP của PC đang telnet vào thiết bị:
IPNI >netstatshow
Active Internet connections (including servers)
PCB Proto Recv-Q Send-Q Local Address Foreign Address (state)
-------- ----- ------ ------ ------------------ ------------------ -------
cf77f9c TCP 1 7 172.16.10.96.23 172.16.254.7.1839 ESTABL
ISHED
cf78020 TCP 0 0 0.0.0.0.22 0.0.0.0.0 LISTEN
cf77f18 TCP 0 0 0.0.0.0.23 0.0.0.0.0 LISTEN
cf77024 TCP 0 0 0.0.0.0.111 0.0.0.0.0 LISTEN
cf76e14 TCP 0 0 0.0.0.0.21 0.0.0.0.0 LISTEN
cf77e10 UDP 0 0 0.0.0.0.520 0.0.0.0.0
Với việc bạn console hay telnet vào bằng địa chỉ dải ip nao vào thì phải cài đặt ACL
cho địa chi ip đó trước. Như ví dụ dung telnet bằng dải ip 203.113.131.x nên việc đặt
ACL như sau:
caclrule 2 ib 203.113.131.0 255.255.255.0 0 allow none 0
caclrule 3 ib 220.231.124.10 255.255.255.255 0 allow none 0
caclrule 4 ib 172.16.0.0 2555.255.0.0 0 allow none 0
caclrule 10 oob 192.168.0.0 255.255.0.0 0 allow none 0
trong đó: ib – inband, oob – outband
Xem ACL:
Gaclrule all
Xoá rule ACL:
Lệnh: Daclrule <rule id>
10. Save configuration and reboot
bootsrc fls
ees
saveconf
restart
B. Cấu hình bằng OPS
1. Cấu hình Profile
a. Tạo ADSL Master profile trên OPS.
Việc tạo Master Profile được ghép bởi 2 Profile là ADSL Channel Profile và
ADSL Line Profile. Các Master Profile được tạo một lần và được sử dụng để gán vào
tất cả các port adsl khi cấu hình.
Chọn Profile Editor ADSL Family ADSL Channel Family Add
Tạo Profile với các thông số như hình dưới:
Chọn Profile Editor ADSL Family ADSL2 Line Family Add
Tạo Profile với các thông số như hình dưới.
ADSL2 Master Family
b. Set ADSL Line Profile cho các port ADSL.
Chọn 1 port Click phải chọn xDSL Configuration Chọn Tab ADSL2 Family Profile
Chọn Profile Master đã tạo ở phần 1 ( theo như hình dưới:
NET+_INTERLEAVE_VIETTEL ) Apply
Nếu cấu hình bằng OPS thì bạn chỉ có thể cấu hình cho từng port ADSL. Có thể làm cho
1 hoặc nhiều card bằng CLI ( hướng dẫn ở phần sau )
2. Cấu hình Vlan cho DSLAM và cho port ADSL.
a. Tạo Vlink ( Flow - service)
Profile Editor EFM Family Ethernet Traffic Descriptor
NEETD_0101: dùng cho egress và ingress
Flow
Các thông số chọn như trên hình trên ( chi tiết tìm hiểu thêm tài liêu training ECI )
b. Tạo Forward Function = brigde
Profile Editor EFM Family Flow
Profile Editor EFM Family Flows Package Profile
c. Add Management_Flow
d. Add Flow vừa tạo ở trên
3. Cấu hình vlan cho port ADSL
Chọn 1 port Click phải chọn Traffic Configuration Add
Chọn tiếp Tab Virtual Port
Chọn tab Traffic Flows : chọn Vlink đã tạo trong mục 1
4. Cấu hình vlan cho port ADSL
Chọn 1 port Click phải chọn Traffic Configuration Add
Chọn tiếp Tab Virtual Port
Chọn tab Traffic Flows : chọn Vlink đã tạo trong mục 1
Hiển thị ra Bridge bạn đã tạo ở mục 2
Chọn Edit
Chọn Complete Vlan Map: Add vlan Access của chính nó, vlan NMS và Access của tất
cả các DSLAM thuộc cùng ring ( trừ vlan nms của chính nó )
Sau đó chọn port 2 ( port hướng downlink )
Chọn Add ….. làm tương tự như port 1.
5. Command Line
Xem Vlink IPNI >pflowconf
||===================================== VLINKS LIST
============================
=========================||
|| VLINK | TYPE |STAT|IngTD|EgTD |SHPM|InPlc|I-VLAN|I-SVLAN|F-ID| ACT|C-
VLAN|PR
I|F|S-VLAN|PRI|F| FF |S||
||------------------------------------------------------------------------------
-------------------------||
|| 0 | PPPoE | 1 | 101 | 101 | DIS| NO | 65535 | 0 | | NO | |
| | | | | BRDG |1||
|| 1 | PPPoE | 1 | 101 | 101 | DIS| NO | 65535 | 0 | | NO | |
| | | | | BRDG |1||
|| 2 | PPPoE | 1 | 102 | 102 | DIS| NO | 65535 | 0 | | NO | |
| | | | | BRDG |1||
||16777216 | PPPoE | 1 | 0 | 0 | DIS| NO | 65533 | 0 | | NO |
| | | | | | BRDG |1||
||2147483627 | MGT | 1 | 0 | 0 | DIS| NO | 65532 | 0 | | NO |
| | | | | | BRDG |1||
Xem các vlan vừa được cấu hình IPNI >gflowinsvlan all
========================================
CURRENT VLAN MAP FOR PORT: 1 VLINK: 16777216
========================================
Row status : 1
Vlans :
871, 872, 873, 874, 875,
=======================================
FORMER VLAN MAP FOR PORT: 1 VLINK: 16777216
======================================
Vlans :
871, 872, 873, 874, 875,
========================================
CURRENT VLAN MAP FOR PORT: 2 VLINK: 16777216
========================================
Row status : 1
Vlans :
871, 872, 873, 874, 875,
=======================================
FORMER VLAN MAP FOR PORT: 2 VLINK: 16777216
=======================================
Vlans :
871, 872, 873, 874, 875,
Tạo thêm vlan 876-900 vào port 1, tương tự cho port 2.
IPNI >sflowinsvlan 1 16777216 add 876-900 SFLOWINSVLAN 1 16777216 add 700, 705-760
1: port 1 trên card IPNI
1677216: vlink id
700, 705-760: vlan id
Chú ý:
Phải add đầy đủ tất cả các VLAN của tất cả các DSLAM trong vòng
Ring này, trừ vlan nms của chính nó
Xem lại Version mới của IPNI card.
IPNI >ver
NI CARD TYPE : IPNI
NI SW VERSION NAME : IPNI_APP_1.30.77
NI SW VERSION DATE : Oct 15 2007
NI SW VERSION TIME : 09:49:10
NI SW VERSION AUTHOR : tomerrei M
NI hardware version 0x3
NI CPA Version = 0x2.a
Xem lại Version của ATUC Card
IPNI>ginv 0 slot
IPNI >ginv 0 1 xem version của slot 1
IPNI >ginv 0 1
============================================================
====================
INVENTORY SHELF = 0, SLOT = 1, PORT = 0, MANI = 0 (IF INDEX =
4194304)
============================================================
====================
RunSWVersion: ATUCP_APP_1.30.63
BootSWVersion: BAP_01.28
HWVersion: 11114000
FirstInstDate: 255255255255T255255255255255T2557033044069
RecentInstDate: 255255255255T2557033044069
SerialNo: 7033044069
VendorID: ECI
UnitID: ATU-C64P POTS
Type: 2703491082
Description: ATU-C64P POTS
ConfigSource: 2
HWdescription: ATU-C64P POTS
Card features: 25292800
LatestActRelease: 1.30.42
LatestActResult: 2
CatalogNumber: Y42820
ProductRevision: A04
Upgrading IOS cho IPNI Card
1. Chỉ để 01 card IPNI vào slot 17
2. Thiết lập kết nối in-band hoặc out-of-band và kiểm tra kết nối đến FTP Server
3. Xem version hiện tại của card IPNI
a. Nếu version khác 1.30.77 với card IPNI và 1.30.63 với card ATUC-P
thì cần Upgrade mới.
b. Nếu version là 1.30.77 với card IPNI và 1.30.63 với card ATUC-P thì
không cần Upgrade, đây là version mới nhất mà ECI cung cấp.
4. Trong serial hoặc telnet terminal, dùng các lệnh sau
setswd dis Disable download Software
swddebug ena Enable debug Software
setrsp 1.30.42 ip-of-ftp-server Hi-FOCuS swdownload aut
1.30.42 Tên thủ tục
ip-of-ftp-server IP của FTP Server: 203.113.188.199
Hi-FOCuS Username của FTP Server
swdownload Password của FTP Server
aut Automatic
setswd ena Enable download Software
5. Sau khi Upgrade Software xong, card sẽ tự động restart
a. IPNI >ver Xem lại Version mới của IPNI card
NI CARD TYPE : IPNI
NI SW VERSION NAME : IPNI_APP_1.30.77
NI SW VERSION DATE : Oct 15 2007
NI SW VERSION TIME : 09:49:10
NI SW VERSION AUTHOR : tomerrei M
NI hardware version 0x3
NI CPA Version = 0x2.a
b. IPNI>ginv 0 slot Xem lại Version của ATUC Card
IPNI >ginv 0 1 xem version của slot 1
IPNI >ginv 0 1
=====================================================
===========================
INVENTORY SHELF = 0, SLOT = 1, PORT = 0, MANI = 0 (IF
INDEX = 4194304)
=====================================================
===========================
RunSWVersion: ATUCP_APP_1.30.63
BootSWVersion: BAP_01.28
HWVersion: 11114000
FirstInstDate: 255255255255T255255255255255T2557033044069
RecentInstDate: 255255255255T2557033044069
SerialNo: 7033044069
VendorID: ECI
UnitID: ATU-C64P POTS
Type: 2703491082
Description: ATU-C64P POTS
ConfigSource: 2
HWdescription: ATU-C64P POTS
Card features: 25292800
LatestActRelease: 1.30.42
LatestActResult: 2
CatalogNumber: Y42820
ProductRevision: A04
Kiểm tra lại Version của các Card
6. Disable việc Download software tự động
setswd dis Disable việc download Software tự động
C. Cấu hình ADSL Service bằng CLI
Cấu hình bằng OPS ít nhất 1 port
Xem index của port đã được cấu hình bằng OPS
Sau đó gán lại cho các port khác bằng CLI
Kiễm tra lai cấu hình và lưu cấu hình
Các bước cấu hình
1. xDSL Configuration
2. Traffic Configuration
1. xDSL Configuration
Xem id của Current Profile
Cấu hình cho nhiều port
Dưới đây là Ví dụ cấu hình cho các port từ 1-10 trên slot 2 của ADSL2/+:
setgenline 0 2 1 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 2 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 3 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 4 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 5 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 6 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 7 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 8 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 9 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 2 10 0 1 2 25 25 50 100 0 0 0 0
Reset modems (Chipset trên ATUC card)
resetmodem 0 2 1
resetmodem 0 2 2
resetmodem 0 2 3
resetmodem 0 2 4
resetmodem 0 2 5
resetmodem 0 2 6
resetmodem 0 2 7
resetmodem 0 2 8
resetmodem 0 2 9
resetmodem 0 2 10
2. Traffic Configuration
Xem id của Traffic Profiles
Xem id của vlink
Create mass connections via CLI
Cấu hình Traffic Configuration cho các port trên Slot 2 theo các thông số sau:
slot: 2
ports: 1-32
vp/vc: 8/35
vlan: 15
vportcr 8 35 A 0 2 1 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 2 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 3 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 4 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 5 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 6 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 7 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 8 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 9 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 2 10 103 103 15 1 S U 0 0 8 8 7 19 0 1 1
Nếu tạo lộn, có thể Delete VC
Delete Virtual Channel của shelf 0 slot 1 port 3
vportrl 8 35 0 1 3
3. Các lệnh hỗ trợ thêm
Debug thông tin trong ECI DSLAM
Viewalltasks
viewalltasks 1 Enable debug
Xem thông tin vlan inband
IPNI >ginvlan
INBAND VLAN ID = 15
INBAND VLAN PRIORITY = 0
Xem bảng MAC address
Etclreadmac
IPNI >etclreadmac <-- Show mac address
Forwarding MAC Table:
=====================
VLAN ID MAC Address port dst cmd src cmd source ID
---------------------------------------------------------------
0011 00:13:49:E9:9C:2B 24 0 0 -1
0011 00:30:88:22:FB:16 22 0 0 -1
0700 00:30:4F:44:C8:55 24 0 0 -1
0700 00:30:88:22:FB:16 22 0 0 -1
0700 00:C0:9F:F4:86:8C 24 0 0 -1
0704 00:14:7F:37:23:15 05 0 0 -1
0704 00:30:88:22:FB:16 22 0 0 -1
4094 00:16:FA:07:A5:0B 16 3 0 -1
4094 00:16:FA:07:C7:F0 05 0 0 -1
4094 00:16:FA:07:C8:5C 06 0 0 -1
press <SPACE> to continue or <ENTER> to quit
Clear MAC address table
Actbridgeaging
IPNI >actbridgeaging Delete mac table
Xem thông tin cấu hình trên EPPROM
IPNI >[0] Eeprom CRC OK
ACTIVE NI SLOT || 0
ALLOWED MODES || 1
AUTO BACKUP USER NAME || anonymous
AUTO BACKUP USER PASSWORD || xx
AUTO CONFIG SAVE MODE || DIS
AUTO FAULT RESET || OFF
AUTO NEGOTIATION MODE || ENA
CATALOG NUMBER || Y33036
DATE OF PRODUCTION || 01 / 2000
DEFAULT GATEWAY || 172.16.45.254 Gateway
DUPLEX MODE || FULL DUPLEX thông tin port
ETHERNET IP ADDRESS || 192.168.20.1 outband ip
ETHERNET IP DEFAULT GATEWAY || 192.168.20.10
ETHERNET IP SUBNET MASK || 255.255.255.0
EXTERNAL T3 CLOCK || 2 MHZ
FCC STATUS || DIS
HW DESCRIPTION || SAM_960
IGMP HOST STATUS || ENA
INBAND IP ADDRESS || 172.16.45.21 inband ip
press <SPACE> to continue or <ENTER> to quit[0] Eeprom CRC OK
INBAND IP DEFAULT GATEWAY || 172.16.45.254
INBAND IP SUBNET MASK || 255.255.255.0
INBAND VLAN ID || 19 vlan nms ( vlan inband )
INBAND VLAN PRIORITY || 0
L2CP STATUS CONTROL || ENA
MASTER FAN STATUS || ENA
MMI_MODE || CLI
MNG PORT || 655360
MULTI NI MODE || SINGLE NI
NI CARD DEBUG MODE || DISABLED
PRIVATE NET ID || 10.10.0.0
PRIVATE NET ID MASK || 255.255.0.0
PRODUCT REVISION || A00
REDUNDANCY MODE || AUTO
REFERENCE TIMING TRANSMISSION || DIS
RING TOPOLOGY || ENA
RTBF DO SAVE || DISABLE
RTBF TASK SWITCH || DISABLE
RTBF RESTART || DISABLE
RTBF STORAGE TYPE || FLASH
SERIAL NUMBER || 32435301
SETUP SOURCE || FLASH
SHELF NAME ||
press <SPACE> to continue or <ENTER> to quit
SHELF TYPE MAIN || 0
SHELF TYPE SUB || 0
SLAVES FAN STATUS || ENA
SWDNLD HOST ADDRESS || 203.113.188.199
SWDNLD HOST PASSWORD || swdownload
SWDNLD HOST USERNAME || Hi-FOCuS
SWDNLD RELEASE STRING || 1.30.42
SWDNLD RESET MODE || MANUAL
SWDNLD STATUS || ENA
SYNTHESIZER MODE || DIS
SYSTEM CONTACT ||
SYSTEM LOCATION ||
SYSTEM NAME ||
TG CURRENT SOURCE A || LINE SOURCE
TG CURRENT SOURCE B || LINE SOURCE
TG PRIORITY TABLE A || 3 1 4 2 7 7
TG PRIORITY TABLE B || 3 1 4 2 7 7
TG QUALITY TABLE A || 1 11 14 8 14 14
TG QUALITY TABLE B || 1 11 14 8 14 14
TG QUALITY THRESHOLD A || 15
press <SPACE> to continue or <ENTER> to quit
TG QUALITY THRESHOLD B || 15
TG SELECTION METHOD A || AUTO PRIORITY
TG SELECTION METHOD B || AUTO PRIORITY
TG SELECTOR A || FORCED_MODE
TG SELECTOR B || FORCED_MODE
TG SELECTOR CONFIGURATION || UNISELECTOR MODE
TG SOURCE MASK TABLE A || 1-NA 2- A 3-NA 4- A 5-NA 6-NA
TG SOURCE MASK TABLE B || 1-NA 2- A 3-NA 4- A 5-NA 6-NA
TG SOURCE STATUS TABLE || 0 1 0 1 0 0
TRANSCEIVER VENDOR || ECI
TRAP DESTINATION 1 || 203.113.188.205
TRAP DESTINATION 2 || 0.0.0.0
TRAP DESTINATION 3 || 0.0.0.0
TRAP INTERVAL || 10
EEPROM VERSION || 0,0,0,0,3
VOIP VLAN CONTROL || 4
VOIP VLAN MEDIA || 6
VOIP VLAN SIGNALING || 4
Xem trạng thái Port ADSL
Gadsl2lstat
gadsl2lstat 0 1 1 Xem trạng thái port ADSL shelf 0, slot 1, port 1 Xem trạng thái port IPNI
Gportstatus ( Xem trên từng port IPNI )
gportstatus a 1 all Port IPNI 1
IPNI >gportstatus a 1 all
hfIPPortStatusInterfaceId = 655360
hfIPPortStatusLinkAlarm = 0
hfIPPortStatusTransceiverFlags = 0
hfIPPortStatusFlowCtrlModeTx = 1
hfIPPortStatusFlowCtrlModeRx = 1
hfIPPortStatusActualMode = 1
hfIPPortStatusOperationalStatus = 1 port đã enable ( nếu = 2 là disable or đã enable nhưng
chưa thông quang, nếu disable thì có thể mở port bằng lệnh: sportconf a 1 2 1 )
hfIPPortStatusTemperature = 11000
hfIPPortStatusTxPower = 3110
hfIPPortStatusRxPower = 434 Tx và Rx #0, có nghĩa là có công suẩt phát, thu
trên 2 port IPNI, đã thông quang
hfIPPortStatusPortId = 0
gportstatus a 2 all Port IPNI 2
Xem vlan permit trên 2 card IPNI
IPNI >gflowinsvlan all
========================================
CURRENT VLAN MAP FOR PORT: 1 VLINK: 16777216
========================================
Row status : 1
Vlans :
1031,1032,1033,1034,1035,
=======================================
FORMER VLAN MAP FOR PORT: 1 VLINK: 16777216
=======================================
Vlans :
1031,1032,1033,1034,1035,
========================================
CURRENT VLAN MAP FOR PORT: 2 VLINK: 16777216
========================================
Row status : 1
Vlans :
1031,1032,1033,1034,1035,
=======================================
FORMER VLAN MAP FOR PORT: 2 VLINK: 16777216
=======================================
Vlans :
1031,1032,1033,1034,1035,
IPNI >
Ghfipportstatus ( Xem trên cả 2 port IPNI )
Ghfipportstatus all all
Xem Index của traffic descriptor
gethtd all
Xem VLINK
Pflowconf
Xem trạng thái của STP
Stpstatus /all
FILE HỖ TRỢ TẠO PROFILE VÀ VLAN BẰNG CLI
Card 1
setgenline 0 1 1 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 2 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 3 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 4 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 5 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 6 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 7 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 8 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 9 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 10 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 11 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 12 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 13 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 14 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 15 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 16 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 17 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 18 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 19 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 20 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 21 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 22 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 23 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 24 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 25 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 26 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 27 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 28 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 29 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 30 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 31 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 32 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 33 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 34 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 35 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 36 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 37 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 38 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 39 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 40 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 41 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 42 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 43 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 44 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 45 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 46 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 47 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 48 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 49 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 50 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 51 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 52 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 53 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 54 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 55 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 56 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 57 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 58 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 59 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 60 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 61 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 62 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 63 0 1 2 25 25 50 100 0 0 0 0
setgenline 0 1 64 0 1 2 25 25 50 100 0 0 0 0
resetmodem 0 1 1
resetmodem 0 1 2
resetmodem 0 1 3
resetmodem 0 1 4
resetmodem 0 1 5
resetmodem 0 1 6
resetmodem 0 1 7
resetmodem 0 1 8
resetmodem 0 1 9
resetmodem 0 1 10
resetmodem 0 1 11
resetmodem 0 1 12
resetmodem 0 1 13
resetmodem 0 1 14
resetmodem 0 1 15
resetmodem 0 1 16
resetmodem 0 1 17
resetmodem 0 1 18
resetmodem 0 1 19
resetmodem 0 1 20
resetmodem 0 1 21
resetmodem 0 1 22
resetmodem 0 1 23
resetmodem 0 1 24
resetmodem 0 1 25
resetmodem 0 1 26
resetmodem 0 1 27
resetmodem 0 1 28
resetmodem 0 1 29
resetmodem 0 1 30
resetmodem 0 1 31
resetmodem 0 1 32
resetmodem 0 1 33
resetmodem 0 1 34
resetmodem 0 1 35
resetmodem 0 1 36
resetmodem 0 1 37
resetmodem 0 1 38
resetmodem 0 1 39
resetmodem 0 1 40
resetmodem 0 1 41
resetmodem 0 1 42
resetmodem 0 1 43
resetmodem 0 1 44
resetmodem 0 1 45
resetmodem 0 1 46
resetmodem 0 1 47
resetmodem 0 1 48
resetmodem 0 1 49
resetmodem 0 1 50
resetmodem 0 1 51
resetmodem 0 1 52
resetmodem 0 1 53
resetmodem 0 1 54
resetmodem 0 1 55
resetmodem 0 1 56
resetmodem 0 1 57
resetmodem 0 1 58
resetmodem 0 1 59
resetmodem 0 1 60
resetmodem 0 1 61
resetmodem 0 1 62
resetmodem 0 1 63
resetmodem 0 1 64
vportcr 8 35 A 0 1 1 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 2 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 3 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 4 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 5 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 6 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 7 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 8 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 9 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 10 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 11 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 12 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 13 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 14 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 15 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 16 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 17 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 18 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 19 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 20 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 21 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 22 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 23 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 24 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 25 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 26 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 27 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 28 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 29 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 30 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 31 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 32 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 33 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 34 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 35 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 36 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 37 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 38 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 39 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 40 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 41 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 42 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 43 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 44 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 45 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 46 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 47 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 48 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 49 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 50 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 51 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 52 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 53 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 54 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 55 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 56 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 57 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 58 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 59 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 60 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 61 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 62 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 63 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
vportcr 8 35 A 0 1 64 101 101 906 0 S U 0 0 8 8 7 19 0 1 1
Set trang thai port
SETPORTSTAT <shelf> <slot> <port> <enable(1) or disable(2)>
setportstat 0 1 1 1
setportstat 0 1 2 1
setportstat 0 1 3 1
setportstat 0 1 4 1
setportstat 0 1 5 1
setportstat 0 1 6 1
setportstat 0 1 7 1
setportstat 0 1 8 1
setportstat 0 1 9 1
setportstat 0 1 10 1
setportstat 0 1 11 1
setportstat 0 1 12 1
setportstat 0 1 13 1
setportstat 0 1 14 1
setportstat 0 1 15 1
setportstat 0 1 16 1
setportstat 0 1 17 1
setportstat 0 1 18 1
setportstat 0 1 19 1
setportstat 0 1 20 1
setportstat 0 1 21 1
setportstat 0 1 22 1
setportstat 0 1 23 1
setportstat 0 1 24 1
setportstat 0 1 25 1
setportstat 0 1 26 1
setportstat 0 1 27 1
setportstat 0 1 28 1
setportstat 0 1 29 1
setportstat 0 1 30 1
setportstat 0 1 31 1
setportstat 0 1 32 1
setportstat 0 1 33 1
setportstat 0 1 34 1
setportstat 0 1 35 1
setportstat 0 1 36 1
setportstat 0 1 37 1
setportstat 0 1 38 1
setportstat 0 1 39 1
setportstat 0 1 40 1
setportstat 0 1 41 1
setportstat 0 1 42 1
setportstat 0 1 43 1
setportstat 0 1 44 1
setportstat 0 1 45 1
setportstat 0 1 46 1
setportstat 0 1 47 1
setportstat 0 1 48 1
setportstat 0 1 49 1
setportstat 0 1 50 1
setportstat 0 1 51 1
setportstat 0 1 52 1
setportstat 0 1 53 1
setportstat 0 1 54 1
setportstat 0 1 55 1
setportstat 0 1 56 1
setportstat 0 1 57 1
setportstat 0 1 58 1
setportstat 0 1 59 1
setportstat 0 1 60 1
setportstat 0 1 61 1
setportstat 0 1 62 1
setportstat 0 1 63 1
setportstat 0 1 64 1
XOÁ VLAN TRÊN PORT ĐÃ TẠO
vportrl 8 35 0 12 1
vportrl 8 35 0 12 2
vportrl 8 35 0 12 3
vportrl 8 35 0 12 4
vportrl 8 35 0 12 5
vportrl 8 35 0 12 6
vportrl 8 35 0 12 7
vportrl 8 35 0 12 8
vportrl 8 35 0 12 9
vportrl 8 35 0 12 10
vportrl 8 35 0 12 11
vportrl 8 35 0 12 12
vportrl 8 35 0 12 13
vportrl 8 35 0 12 14
vportrl 8 35 0 12 15
vportrl 8 35 0 12 16
vportrl 8 35 0 12 17
vportrl 8 35 0 12 18
vportrl 8 35 0 12 19
vportrl 8 35 0 12 20
vportrl 8 35 0 12 21
vportrl 8 35 0 12 22
vportrl 8 35 0 12 23
vportrl 8 35 0 12 24
vportrl 8 35 0 12 25
vportrl 8 35 0 12 26
vportrl 8 35 0 12 27
vportrl 8 35 0 12 28
vportrl 8 35 0 12 29
vportrl 8 35 0 12 30
vportrl 8 35 0 12 31
vportrl 8 35 0 12 32
vportrl 8 35 0 12 33
vportrl 8 35 0 12 34
vportrl 8 35 0 12 35
vportrl 8 35 0 12 36
vportrl 8 35 0 12 37
vportrl 8 35 0 12 38
vportrl 8 35 0 12 39
vportrl 8 35 0 12 40
vportrl 8 35 0 12 41
vportrl 8 35 0 12 42
vportrl 8 35 0 12 43
vportrl 8 35 0 12 44
vportrl 8 35 0 12 45
vportrl 8 35 0 12 46
vportrl 8 35 0 12 47
vportrl 8 35 0 12 48
vportrl 8 35 0 12 49
vportrl 8 35 0 12 50
vportrl 8 35 0 12 51
vportrl 8 35 0 12 52
vportrl 8 35 0 12 53
vportrl 8 35 0 12 54
vportrl 8 35 0 12 55
vportrl 8 35 0 12 56
vportrl 8 35 0 12 57
vportrl 8 35 0 12 58
vportrl 8 35 0 12 59
vportrl 8 35 0 12 60
vportrl 8 35 0 12 61
vportrl 8 35 0 12 62
vportrl 8 35 0 12 63
vportrl 8 35 0 12 64
HƯỚNG DẪN CÀI ĐẶT CẤU HÌNH THIẾT BỊ RAISECOM
RC953 A. Nội dung
Bài hướng dẫn bao gồm các nội dung như sau
Cấu hình tạo kết nối E1 giữa các thiết bị của Raisecom
Cấu hình chế độ frame cho cổng E1
Cấu hình tạo các Virtual Channel
Cấu hình chế độ VLAN của các Virtual Channel
Cấu hình SNMP cho RC953
Hướng dẫn cấu hình các thiết bị thông qua phần mềm NView NNM
B. Hướng dẫn cấu hình và cài đặt
I. Mô hình kết nối
1) Mô hình kết nối các thiết bị của Raisecom với Switch hoặc Router
Hình 1 : Topology 1
2) Mô hình kết nối các thiết bị của Raisecom trực tiếp với các PC
RC-954
RC-953
RC-954
E1
E1
FE`
`FE
PC
PC
`FE
PC
Hình 2 : Topology 2
II. Lắp đặt thiết bị
Các thiết bị sẽ được lắp đặt dựa theo topology 1 hoặc 2. Cách đấu nối
cổng E1 từ thiết bị RC954 đến thiết bị RC953 được miêu tả như sau :
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
RC953
RC954
Interface E1
Interface E1
Interface E1
1 2 3 4 5 6 7 8
RC954
Interface E1 Interface E1 Interface E1
III. Cấu hình thiết bị bằng dòng lệnh
1. Đối với topology thứ nhất
- Truy nhập vào thiết bị RC953 thông qua cổng Console
Login : raisecom
Password : raisecom
Raisecom> enable
Password : raisecom
- Cấu hình chế độ frame cho các cổng E1 trên RC953
RC953E3FE16E1#config t
RC953E3FE16E1(config)# interface e1 1
RC953E3FE16E1(config-e1/0/1)# frame-mode
framed
RC953E3FE16E1(config)# interface e1 2
RC953E3FE16E1(config-e1/0/2)# frame-mode
framed
…………………
RC953E3FE16E1(config)# interface e1 16
RC953E3FE16E1(config-e1/0/12)# frame-mode
framed
Bởi vì thiết bị RC954 làm việc ở chế độ inverse
multiplexing và cổng E1 là chế độ frame, vì thế ta phải
cấu hình cổng E1 trên RC953 cùng ở chế độ frame để
chúng có thể kết nối với nhau.
Để kiểm tra các chế độ trên cổng E1 ta có thể sử dụng
câu lệnh
RC953E3FE16E1(config)# interface e1 1
RC953E3FE16E1(config-e1/0/1)# show interface
- Cấu hình tạo Virtual Channel
RC953E3FE16E1#config t
RC953E3FE16E1(config)# virtual-channel 1 e1 1-4
RC953E3FE16E1(config)# virtual-channel 5 e1 5-8
RC953E3FE16E1(config)# virtual-channel 9 e1 9-12
Mỗi một Virtual Channel ứng với 1 cổng E1 trên
RC953, vì thế ta có thể tạo ra 16 virtual channel.
Ví dụ ở đây ta nhóm 4 cổng E1 từ 1 đến 4 vào channel
1
4 cổng E1 từ 5 đến 8 vào channel 5
4 cổng E1 từ 9 đến 12 vào channel 9
Ta có thể kiểm tra việc cấu hình tạo virtual channel
bằng lệnh :
RC953E3FE16E1(config)# show virtual-channel
- Cấu hình chế độ VLAN của các Virtual Channel
RC953E3FE16E1#config t
RC953E3FE16E1(config)# interface switchport 1
RC953E3FE16E1(config-eswif/0/1)# switchport trunk
allowed vlan 100,200,300
RC953E3FE16E1(config)# interface switchport 17
RC953E3FE16E1(config-eswif/0/17)# switchport
trunk allowed vlan 100,200,300
+ Giả sử trên switch đang có các VLAN 100,200 và
300. Ta sẽ cấu hình tạo trunk trên switchport 1, cho
phép VLAN100, 200 và 300 đi qua.
Switchport 1 ở đây sẽ tương ứng với channel 1
+ Switchport 17.18.19 tương ứng với interface FE1,2
và 3
2. Đối với topology thứ 2
Tất cả đều cấu hình giống như trên ngoại trừ cấu hình chế
độ VLAN của các virtual channel
Đối với trường hợp này ta sẽ phải cấu hình cho interface
switchport ở chế độ accesss
RC953E3FE16E1#config t
RC953E3FE16E1(config)# interface switchport 1
RC953E3FE16E1(config-eswif/0/1)# switchport
accesss vlan 100
RC953E3FE16E1#config t
RC953E3FE16E1(config)# interface switchport 17
RC953E3FE16E1(config-eswif/0/1)# switchport
accesss vlan 100
IV. Cấu hình thiết bị thông qua phần mềm NView NNM
1. Tạo kết nối SNMP
Để có thể cấu hình được thiết bị thông qua phần mềm NView NNM,
trước tiên ta phải cấu hình snmp cho RC953 bằng dòng lệnh
Ta sẽ cấu hình tạo snmp như sau:
RC953E3FE16E1#config t
RC953E3FE16E1(config)#snmp trap-server 192.168.x.x 162
Đây là câu lệnh tạo snmp server. Địa chỉ IP có thể lấy từ IP của PC
cài đặt NView NNM. 162 là port UDP cho snmp.
RC953E3FE16E1#config t
RC953E3FE16E1(config)#interface snmp
RC953E3FE16E1(config-snmp)#ip add 192.168.x.x 255.255.x.x
RC953E3FE16E1(config-snmp)#no shut
Đây là câu lệnh gán IP quản trị cho cổng SNMP, địa chỉ IP có thể
lấy bất kỳ
RC953E3FE16E1(config)# snmp-server community public ro
RC953E3FE16E1(config)# snmp-server community private rw
Đây là câu lệnh tạo community cho snmp-server. Ro và Rw là các
thông số tương ứng với NNM.
2. Cài đặt NView NNM trên máy tính
a. Phần mềm cần có
- NViewNNM V5.exe
- RC953E-3FE16E1_5.1(build4)_20090113.exe
- SP1(Build9)_NNM5_20080530.exe
- License cho các node của RC953
b. Các bước cài đặt trên máy tính
Bước 1 : Chạy file NViewNNMV5.exe
Ấn Next để tiếp tục
Bước 2 : Lựa chọn database
Bước 3 : Chọn file License và add vào yêu cầu
Lựa chọn Next để tiếp tục
Bước 4 : Chương trình sẽ được tự động cài đặt
Bước 5 : Chạy file SP1(Build9)_NNM5_20080530.exe, cài đặt tương tự như các
bước trên
Bước 6 : Chạy file RC953E-3FE16E1_5.1(build4)_20090113.exe, cài đặt tương
tự các bước trên
Sau khi cài đặt đầy đủ các file ở trên, bắt đầu chạy phần mềm NView NNM
Giao diện ban đầu sẽ như sau
User name : administrator
Password : raisecom
Add các thiết bị vào phần mềm
3. Giao diện cấu hình
3.1. Cấu hình tạo chế độ frame và unframed cho cổng E1
Nháy đúp vào thiết bị RC953
Chọn Config Manager
Manager
Thay đổi chế độ frame hoặc unframed cho cổng E1
3.2. Cấu hình tạo các virtual channel
3.3. Cấu hình tạo access hoặc trunking
Lưu lại cấu hình thiết bị
Cấu hình cho thiết bị RC954
Nháy đúp chuột vào icon thiết bị RC954
Cài đặt chế độ cho cổng E1 của RC954
I. RC956-FE8E1 (RC006-1M).
Hình 1: Mặt trước
Hình 2: Mặt sau
Một số đặc tính của RC006-1M:
- Sử dụng giao thức chuyển đổi tử Ethernet sang E1.
- Hỗ trợ giao diện CONSOLE.
- Hỗ trợ giao diện SNMP.
Trong việc hỗ trợ của quản lý thông qua các module của chassis và
quản lý thiết bị đầu xa.
- Hỗ trợ nâng cấp trực tuyến và rễ ràng bảo quản.
Kích thước chuẩn:
- Thiết bị dùng theo chuẩn 19-inch 1U chassis.
- Kích thước: 430mm (Width) x 44.45mm (Height) x 266mm (Depth)
Nguồn cung cấp:
RC006-1M cung cấp 2 module sử dụng nguồn AC và DC
- Điện áp nguồn cung cấp: -48V DC, khoảng điện áp: -36V ~ -72V
100~220V AC
- Công suất tiêu thụ:
o Công suất tiêu thụ < 5W khi chưa sử dụng module.
o Công suất tiêu thụ < 15W khi sử dụng module.
Sơ đồ kết nối (dùng RC006-1M làm trung tâm):
traffic
Outband-nms
Switch
IP: 172.16.142.2/24
Vlan: 20
Traffic: trunk
Outband nms: access
FE-1
FE-2
FE-1
FE-8E1-(nxE1)
DSLAM
IP: 172.16.142.11/24
Vlan: 20
sw1: all on
sw2: 3,4: on
Sw3: all off
IP: 172.16.142.3/24
E1-(nxE1)
SDH
DSLAM
IP: 172.16.142.12/24
Vlan: 20
DSLAM
IP: 172.16.142.13/24
Vlan: 20
E1-(nxE1)
Hinh 3: Sơ đồ mạng dùng RC956-FE8E1 làm trung tâm
RC006 hỗ trợ quản lý outband qua đường Ethernet được đấu thẳng lên
switch. Với mô hình này việc quy hoạch ip và vlan sẽ được cấu hình
theo quy hoạch của tỉnh.
- Với đường nms: cấu hình access vlan giám sát của tỉnh (ex: 20
hinh3)
- Với đường traffic thì được support port trunk nhiều vlan nên có thể
được cầu hình như các port thông thường trên switch.(đường nms
và traffic được tách biệt nên không sợ bị loop).
- Thiết bị này hỗ trợ việc remote đầu xa để xem thông tin và kiểm
tra trạng thái luồng
- Hỗ trợ Link-Aggregation để nhóm các đường E1.
2. Config Converter RC956FE84E1
Console. Raisecom hỗ trợ console vào thiết bị theo cổng COM (RS-232). Việc console vào
thiết bị để cho các thiết bị như: RC935_8FE16E1, RC956FE8E1. Các bước để console
vào thiết bị:
Console vào thiết bị theo cổng COM(RS-232):
Sử dụng cáp console 2 cổng RS-232 (đực và cái) và dùng phần mềm Hyper Terminal để
console vào Raisecom với các thông số cho cổng COM sau:
• Bit per second: 9600
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
Login vào thiết bị theo username và password mặc định như sau:
Username: raisecom
Password: raisecom
a.Cấu hình Raisecom RC006:
Bước 1: Configure E1.
Cấu hình 2 luồng E1 sử dụng trên môt port (thực chất là sử dụng một đường và
một đường là ảo có thể mở rộng sau này): trên port e1 1 và 2.
- Đặt chế độ framed
- Đặt clock-mode master
- Đặt crc-auto enable
RC006# config
Configuration mode, one conmmand input per time. End with CTRL-Z.
RC006(config)# slot 1
RC006(config-slot/1)# interface e1 1
RC006(config-e1/1/1)# frame-mode framed
RC006(config-e1/1/1)# clock-mode master
RC006(config-e1/1/1)# crc-auto disable
RC006(config-slot/1)# interface e1 2
RC006(config-e1/1/2)# frame-mode framed
RC006(config-e1/1/2)# clock-mode master
RC006(config-e1/1/2)# crc-auto disable
Bước 2: Configuration Ethernet.
- Cấu hình điều khiển dữ liệu truyền của dịch vụ trên cổng Ethernet:
RC006(config-slot/1)# esw isolated
- Cấu hình kênh ảo với sự cấu hình đóng gói gói tin trên đường E1:
RC006(config-slot/1)# virtual-channel 1 e1 1-2
- Cấu hình phân phối chuyển mạch trên cổng ethernet:
RC006(config-slot/1)# interface switchport 1
RC006(config-eswif/2/1)# switchport hybrid allowed vlan 29 (Vlan NMS)
RC006(config-eswif/2/1)# switchport hybrid allowed vlan 1247 (Vlan
User)
- Cấu hình cổng lến switch.
RC006(config-slot/1)# interface switchport 9
RC006(config-eswif/2/9)# switchport hybrid allowed vlan 29 (Vlan NMS)
RC006(config-eswif/2/9)# )# switchport hybrid allowed vlan 1247 (Vlan
User)
Bước 3: Cấu hình giám sát SNMP.
- Kiểm tra ip SNMP của converter:
RC006# show interface snmp
Interface:snmp
Administration Status : up Operation Status : up
Description: snmp
Internet address: 192.168.4.28 Netmask: 255.255.255.0
Ethernet address: 00:0e:5e:03:46:e0
Duplex:full-duplex Speed:100baseT
Autonegotiation:enable
- Cấu hình port access trên switch permit cho một vlan Z được đặt ip cùng dải
với ip trên raisecom, khi đó ta có thể telnet vào thiết bị raisecom thông qua
interface snmp.
Bước 4: Save cấu hình
RC006# write
Are you sure[Y/N]:y
Please wait..Copy OK: 1807 bytes copied
Save current configuration successfully!
b.Cấu hình Raisecom RC953-FE4E1
Cấu hình cho cRC953-FE4E1 là các việc gạt các swtich trên thiết bị. Các thông số
để gạt switch khi cấu hình cho các đường E1 là:
SW1: All first bit have to be ON
SW2: All used interfaces are at OFF passion, other: ON
SW3: All Off
Gạt xuống – ON
Gạt lên - OFF
Chú ý: Sau mỗi lần thay đổi vị trí các switch thì phải restart lại thiết bị để nhận cấu
hình mới.