hand drawing manual
TRANSCRIPT
-
7/30/2019 Hand Drawing Manual
1/13
FACULTY OF ENGINEERING, ARTCHITECTURE & BUILT
ENVIRONMENT
HAND DRAFTING MANUAL
EM101/ED109/EE202
ENGINEERING GRAPHICS & DESIGN / ENGINEERING DESIGN
Lecturer/Instructor: _________________________________________
Name: __________________________________________________
Student ID: ______________________________________________
Course: _________________________________________________
MAY 2012
-
7/30/2019 Hand Drawing Manual
2/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 1 | P a g e
TABLE OF CONTENTS
1 General Instructions 2
2 Laboratory Protocols 2
3 Title Block 2
4 Classwork
Classwork 1 Freehand Sketching 4
Classwork 2 Instrumental Drawing 5
Classwork 3 Geometric Constructions 6
Classwork 4 Orthographic Projection 7
Classwork 5 Dimensioning and Tolerancing 8
Classwork 6 Sectional Views 9
Classwork 7 Auxiliary View 10
Classwork 8 Oblique Projections 11
Classwork 9 Isometric Projections 12
-
7/30/2019 Hand Drawing Manual
3/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 2 | P a g e
1 GENERAL INSTRUCTIONS
The lessons in this manual are designed to provide the students some fundamental concepts in
hand drafting. Students are required to practice the exercises as designed in the manual. All
exercises are to be completed within the allotted time.
2 LABORATORY PROTOCOLS
Students are required to comply with the following rules when in the lab.
1. Swapping of lab session is strictly not allowed. Work done in other than the registered labsession will be graded zero (0).
2. Always be punctual. Students later than 15 minutes are not allowed to enter the lab.3. All hand phones must be switched off. (Lecturer/instructor reserves the right not to allow
students who do not follow this rule to enter the lab).
4. Eating and drinking in the lab are strictly prohibited.5. Students should prepare their own drafting equipment for every lab session.6. Always follow the instruction of the lab instructor or lecturer before the start of the lab.7. Clean the working area and return all benches to their respective places before you leave
the lab.
8. All class work must be completed and submit within the allotted time. Any latesubmission will be graded zero.
3 TITLE BLOCKStudents shall use the title block, as shown in the following page, for every classwork.
-
7/30/2019 Hand Drawing Manual
4/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 3 | P a g e
-
7/30/2019 Hand Drawing Manual
5/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 4 | P a g e
CLASSWORK 1 FREEHAND SKETCHING
Students are required to sketch a drafting table (from any angle) on the A3 drawing sheet.
Title block is not required for this particular classwork.
-
7/30/2019 Hand Drawing Manual
6/13
-
7/30/2019 Hand Drawing Manual
7/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 6 | P a g e
CLASSWORK 3 GEOMETRIC CONSTRUCTIONS
-
7/30/2019 Hand Drawing Manual
8/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 7 | P a g e
CLASSWORK 4 ORTHOGRAPHIC PROJECTION
-
7/30/2019 Hand Drawing Manual
9/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 8 | P a g e
CLASSWORK 5 DIMENSIONING AND TOLERANCING
-
7/30/2019 Hand Drawing Manual
10/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 9 | P a g e
CLASSWORK 6 SECTIONAL VIEWS
-
7/30/2019 Hand Drawing Manual
11/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 10 | P a g e
CLASSWORK 7 AUXILIARY VIEWS
-
7/30/2019 Hand Drawing Manual
12/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 11 | P a g e
CLASSWORK 8 OBLIQUE PROJECTION
-
7/30/2019 Hand Drawing Manual
13/13
EM101/ED109/EE202 | Engineering Graphics and Design
Updated Jan 2012 12 | P a g e
CLASSWORK 9 ISOMETRIC PROJECTION