h technical product data fw pressure pipe systems - · pdf filepipes and fittings pipes and...
TRANSCRIPT
© E Engineering GmbHAll rights reserved.
Publication: 10/2012
All rights reserved. No part of this document may be reproduced or utilized in any form or by any means without our prior written permission.All information in the document is correct at the time of going to press. However, we reserve the right to make changes withoutnotice, in particular to technical data. The data given is not binding and must therefore be checked in each individual case and revised asappropriate.
Thermoplastic Liner
- FEP - Fluorinated ethylene propylene
- PFA - Perfluoroalkoxy
- PE-HD - High Density Polyethylen PVC-C - Chlorinated polyvinyl chloride
- PP - Polypropylene
- PVDF - Polyvinylidene fluoride
- ECTFE - Ethylene chlorotrifluoroethylene
- PVC - Polyvinyl chloride (chlorinated PVC-C, unplasticized PVC-U)
Process equipment according to PED (Process Equipment Directive)
- Vessels for acids and bases
- Bio Reactors
- Chlorine Drying Towers
- Cyclones
- Ducting
- Electro Filters
- Scrubbers
- Double Chamber Storage Tanks for chemicals
- Customized Shapes and Configurations
Standard product range
- Pipes, Joints, Fittings (DIN 16965/66: Pipe Type D, E, N, B)
Mining Industry
Temperature range up to 160° C (higher temperatures on request)
Nominal Diameter [DN]
Nominal Pressure [PN]
25 - 4000
1 - 40
Pipe systems
Textile, Paper and Pulp Industry
Metal Industry
Power Industry
Fields of application:
HOBAS FW Pressure Pipe Systems
HOBAS supplies various kinds of industries where a large variety of operating conditions call for chemically, mechanically and thermally resistant pipelines, vessels and process equipment. HOBAS Industrial Products are made from GRP (Glass Fiber Reinforced Plastic) which can be optionally equipped with a thermoplastic liner. According to specifications and customer requirements, products are manufactured by filament winding or hand lamination.
Chemical Industry Semiconductor Industry
Sea Water Desalination
Plastics Industry
Air Treatment
3
Abbreviations:
b Flange sheet, loose flange
D Outer flange diameter
di Inner pipe diameter
DIN German Institute for Standardization
DN Nominal Diameter
s4 Pipe wall thickness (Pipe Type B without thermoplastic liner)
s3 Structure laminate
s2 Chemical protection layer
s1 Thickness of thermoplastic liner (for Pipe Type B)
FW Filament Winding
k Bolt circle diameter
L Length
PN Nominal Pressure
R Radius
GRP Glass fiber plastic (glass fiber reinforced unsaturated polyester resin)
4
A40
A41
A42
A43
A44
A44
B41
B42
C41
C42
C43
C43
C44
C44
C45
C45
D41
D42
D43
D44
D45
E41
E42
E43
F41
SMC Loose Backing Ring
SMC Stub Flange
SMC Blind Flange
AC
CE
SS
OR
IES
Material Specifications
FIT
TIN
GS
Pipe Type D
Pipe Type E
Pipe Type N
Laminated and Welded Joint Pipe Type B
Pipe Type B
Laminated Joint Pipe Type D / E / N
Storage Tank
Pipe Spool Manufacture
GRP Header
PR
OC
ES
S
EQ
UIP
ME
NT
Stub Flange D / E / N / B
Overview Pipes and Wall Structure
Pipes and Fittings
Radiused Bends D / E / N / B
PIP
ES
PIP
E J
OIN
TS
Cyclone
Absorber
Miter Bends D / E / N / B
T-piece D / E / N / B DN 25-250
T-piece D / E / N / B DN 300-1000
Reducers D / E / N / B DN 25-250
Reducers D / E / N / B DN 300-1000
Fixed Flange D / E / N / B
5
Pipe Type Din compliance with
DIN 16965, part 4
Glass contents:
25%Glass contents:
55%Glass contents:
0%
Pipe Type Ein compliance withDIN 16965, part 5
Glass contents:
25%Glass contents:
30%Glass contents:
0%
Pipe Type Nin compliance with
DIN 16965
Glass contents:
25%Glass contents:
40%Glass contents:
0%
Pipe Type Bin compliance withDIN 16965, part 2
Glass contents:
55%Glass contents:
0%
Chemical protection layer Structure laminate Outer surface
Overview Pipes and Wall Structure
Resin-rich with C-glass fleece or synthetic fleece
Glass fiber stands, -mats and -fabric
Resin-rich with C-glass fleece or synthetic fleece
2,5mm
Chemical protection layer
s2
Structure laminate Outer surface
s3
dependent on pressure class
s2 s3
0,4mm
Resin-rich with C-glass fleece or synthetic fleece
Hand lay-up laminate with textile glass mats
Resin-rich with C-glass fleece or synthetic fleece
0,2mmdependent on pressure class
PVC, PVC-C, PVC-U, PE-HD, PP, PVDF, ECTFE, FEP, PFA
Glass fiber stands, -mats and -fabric
Resin-rich with C-glass fleece or synthetic fleece
Chemical protection layer Structure laminate Outer surface
Thermoplastic liner
s1 s3
2,5 mm
Resin-rich with C-glass fleece or synthetic fleece
Glass fiber stands, -mats and -fabric
0,2mmdependent on pressure class
Chemical protection layer Structure laminate Outer surface
s2 s3
0,2mm
Resin-rich with C-glass fleece or synthetic fleece
3,5 mm
0,2mm
A40
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
6
Pipes and Fittings
Pipes and Fittings with laminated ends
Pipes and Fittings with one laminated end and one flange joint (fixed or loose flange)
Pipes and Fittings with flange joints (fixed or loose flange)
Pipes and Fittings Pipe Type D, E, N
Pipes and Fittings Pipe Type B with thermoplastic liner
Pipes and Fittings with laminated / welded ends
Pipes and Fittings with one laminated end and one flange joint (fixed or loose flange)
Pipes and Fittings with flange joints (fixed or loose flange)
A41
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
7
PN 16
di * L ** s4 min*
[mm] [m] [mm]
25 5 4,4
32 6 4,4
40 6 4,4
50 6 4,4
65 6 4,4
80 6 4,4
100 6 4,4
125 6 4,4
150 6 4,6
200 6 5,3
250 6 6,0
300 6 6,6
350 6 7,3
400 6 8,0
500 6 9,3
600 6 10,7
700 6 12,0
800 6 13,4
900 6 14,8
1000 6 16,1
*** Standard pipe length, other lengths available
DN
65
50
40
32
25
350
300
250
100
80
On request
4,4
4,4
4,4
Pipe Type D
1000
Tolerances in accordance with DIN 16965, part 4
> PN 16 on request
Pipe Type D is produced to DIN 16965 part 4 on the basis of UP and vinylester resins. Pipes of this same type can be joined by laminates (see Pipe Joints) or flanges (see Fittings).
400
500
600
700
800
900
125
150
200
1100 - 4000
PN 10
s4 min*
[mm]
4,4
4,4
4,4
4,4
4,4
4,4
4,4
4,7
5,1
9,3
10,1
11,0
5,5
5,9
6,8
7,6
8,4
A42
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
8
PN 6 PN 10 PN 16
di * L ** s4 min* s4 min* s4 min*
[mm] [m] [mm] [mm] [mm]
25 5 5,0 5,0 5,0
32 6 5,0 5,0 5,0
40 6 5,0 5,0 5,0
50 6 5,0 5,0 5,0
65 6 5,0 5,0 5,1
80 6 5,0 5,0 6,1
100 6 5,0 5,0 7,3
125 6 5,0 5,9 8,9
150 6 5,0 6,8 10,5
200 6 5,6 8,7 13,6
250 6 6,7 10,7 16,8
300 6 7,9 12,6 19,9
350 6 9,0 14,5 23,1
400 6 10,1 16,4 26,2
500 6 12,4 20,3 32,5
600 6 14,7 24,1 38,8
700 6 17,0 27,9 45,1
800 6 19,2 31,8 51,4
900 6 21,5 35,6 57,7
1000 6 23,8 39,5 64,0
***
Tolerances in accordance with DIN 16965, part 5Standard pipe length, other lengths available
> PN 16 on request
350
400
500
600
700
800
1100 - 4000 On request
900
1000
Pipe Type E
Pipe Type E is produced and reinforced with glass fiber to DIN 16965 part 5 on the basis of UP and vinylester resins. Pipes of this same type can be joined by laminates (see Pipe Joints) or flanges (see Fittings).
DN
300
25
32
40
50
65
80
100
125
150
200
250
A43
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
9
PN 10 PN 16
di * L ** s4 min* s4 min*
[mm] [m] [mm] [mm]
25 6 5,0 5,0
32 6 5,0 5,0
40 6 5,0 5,0
50 6 5,0 5,0
65 6 5,0 5,0
80 6 5,0 5,1
100 6 5,0 5,7
125 6 5,0 6,4
150 6 5,4 7,2
200 6 6,3 8,7
250 6 7,2 10,2
300 6 8,1 11,7
350 6 9,0 13,2
400 6 10,0 14,7
500 6 11,8 17,7
600 6 13,6
700 6 15,4
800 6 17,3
900 6 19,1
1000 6 20,9
*** Standard pipe length, other lengths available
500
600
700
800
900
1000
1100 - 4000
> PN 16 on request
plus tolerances
On request
400
40
50
65
80
100
125
150
200
250
300
350
32
Pipe Type N
Pipe Type N is produced on the basis of UP and vinylester resins. Pipes of this same type can be joined by laminates (see Pipe Joints) or flanges (see Fittings).
DN
25
A44
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
10
PN 6 PN 10 PN 16
L ** s4 min * s4 min * s4 min *
[m] [mm] [mm] [mm]
5-6 2,9 2,9 2,9
5-6 2,9 2,9 2,9
5-6 2,9 2,9 2,9
5-6 2,9 2,9 2,9
5-6,2 2,9 2,9 2,9
5-6,2 2,9 2,9 2,9
5-6,2 2,9 2,9 2,9
5-6,2 2,9 2,9 2,9
5-6,2 2,9 2,9 3,2
5-6,2 2,9 2,9 3,7
5-6,2 2,9 3,1 4,4
5-6,2 2,9 3,7 5,3
5-6,2 2,9 4,0 5,8
5-6,2 3,1 4,4 6,4
5-6,2 3,6 5,2 7,8
5-6,2 4,1 6,1 9,1
5-6,2 4,6 7,0 10,6
5-6,2 5,1 7,7 11,8
5-6,2 5,6 8,6 13,2
5-6,2 6,1 9,4 14,5
***
65
Pipe Type B
125
DN
25
32
40
50
* di dependent on the thermoplastic liner
Pipe Type B is glass fiber reinforced with thermoplastic liner and produced to DIN 16965 part 2 on the basis of UP and vinylester resins. Pipes of this type can be joined with either welded or laminated joints (see Pipe Joints) or flanges (see Fittings).
The resistance against aggressive media depends on the thermoplastic liner. PVC, PVC-C, PVC-U, PE-HD, PP, PVDF, ECTFE, FEP and PFA are processed as standard according to customer requirements.
300
350
400
1000
80
100
200
250
150
500
600
700
800
900
> PN 16 on request
Tolerances in accordance with DIN 16965, part 2Standard pipe length, other lengths available
On request1100 - 4000
A45
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
11
L1 min s5 min L1 min s5 min L1 min[mm] [mm] [mm] [mm] [mm]
110 4,0 110 4,0 110
110 4,0 110 4,0 110
110 4,0 110 4,0 110
110 4,0 110 4,0 110
110 4,0 110 4,5 110
110 4,0 110 5,0 120
110 4,0 110 6,5 140
110 5,0 110 8,0 175
110 6,0 130 9,5 210
110 8,0 165 13,0 280
125 10,0 205 16,0 345
150 11,5 250 19,0 415
170 13,5 290 22,0 460
200 15,5 330 25,0 550
240 19,5 410 31,5 685
290 23,0 480 38,0 745
335 27,0 560 44,0 880
390 31,0 640 50,0 990
430 35,0 720 57,0 1115
480 39,0 795 63,0 1235
18,5
20,5
4,5
6,0
7,0
8,0
9,0
4,0
4,0
4,0
5,0
6,0
Tolerances:
> PN 16 on request
350
400
500
600
700
800
900
1000
On request1100-4000
23,0
11,5
14,0
16,0
250
300
80
DN
65
PN 10
100
125
150
200
s5 min[mm]
4,0
4,0
4,0
Laminated Joint Pipe Type D / E / N
25
32
40
50
Joints are laminated to permanently connect pipes and fittings type D, E and N to DIN 16966, part 8.
PN 16
4,0
PN 6
B41
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
12
L1 s5 min L1 s5 min L1[mm] [mm] [mm] [mm] [mm]
110 4,0 110 4,0 110
110 4,0 110 4,0 110
110 4,0 110 4,0 110
110 4,0 110 4,0 110
110 4,0 110 4,0 110
110 4,0 110 4,0 120
110 4,0 110 4,5 140
110 4,0 110 5,5 175
110 4,0 130 6,5 210
110 5,5 165 8,5 280
125 6,5 205 10,5 345
150 8,0 250 12,5 415
170 9,0 290 15,0 460
200 10,5 330 17,0 550
240 13,0 410 21,0 685
290 15,5 480 25,0 745
335 18,0 560 29,5 880
390 20,5 640 33,5 990
430 23,0 720 37,5 1115
480 26,0 795 42,0 1235
> PN 16 on request
Laminated and Welded Joint Pipe Type B
15,5
PN 6
8,0
9,5
11,0
12,5
14,0
4,0
4,0
5,0
5,5
6,5
4,0
4,0
DN
25
1000
80
100
125
150
200
250
4,0
4,0
[mm]
4,0
4,0
4,0
32
40
Joints are welded and laminated to permanently connect type B pipes and fittings with thermoplastic liner to DIN 16966, part 8.
s5 min
65
50
PN 10 PN 16
4,0
4,0
t2 = 10-20mm
300
350
400
500
600
700
800
900
1100 - 4000 On request
B42
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
13
90° 45°
L L[mm] [mm]
110 70
130 80
150 90
180 105
140 85
165 100
205 115
245 135
285 150
365 190
450 225
525 260
600 290
680 325
830 390
950 430
1100 490
1250 545
* DN 25 - 125: ± 0,5mm | DN 150 - 250: ± 1,0mm | DN 300 - 400: ± 1,5mm | DN 500 - 700: ± 2,0mm | DN 800 - 1000: ± 2,5mm
157
532
654
693
850
195
283
362
405
463
Radiused Bends D / E / N / B
100
125
150
200
DNR
[m]
72
88
104
71
84
105
138
32
40
50
65
80
800
Pipe Type B: Dimensions dependent on the thickness of the thermoplastic liner.
1000
Radiused bends are glass fiber reinforced and produced to DIN 16966 part 2 on the basis of UP and vinylester resins. Bends are available with 45° and 90° angles as standard, other angles are available on request. Pipes of this type can be connected with laminated joints (see Pipe Joints) or flanges (see Fittings).
Radiused Bend 45° Radiused Bend 90°
350
400
500
600
700
250
300
25
C41
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
14
R L R L[m] [mm] [mm] [mm]
400 550 500 300
400 575 500 400
450 625 550 400
450 650 550 425
525 700 600 425
600 800 600 450
750 950 750 525
900 1075 900 600
1050 1200 1050 650
1200 1350 1200 700
1350 1450 1350 725
1270 1570 1270 750
* DN 25 - 125: ± 0,5mm | DN 150 - 250: ± 1,0mm | DN 300 - 400: ± 1,5mm | DN 500 - 700: ± 2,0mm | DN 800 - 1000: ± 2,5mm
1000
1100 - 4000 On request
Pipe Type B: Dimensions dependent on the thickness of the thermoplastic liner.
700
800
900
400
500
600
250
300
350
150
200
Miter bends are glass fiber reinforced and produced to DIN 16966 part 2 on the basis of UP and vinylester resins. Bends are available with 45° and 90° angles as standard, other angles are available on request. Pipes of this type can be connected with laminated joints (see Pipe Joints) or flanges (see Fittings).
DN
90° 45°
Miter Bends D / E / N / B
Miter bend 90° Miter bend 90°
C42
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
15
L2
[mm]
170
170
180
190
195
205
270
240
240
290
260
310
310
340
205
285
365
0
100
125
100
125
150
125
150
200
450
32
40
150
200
250
40
50
65
50
65
80
65
80
100
80
25
32
25
Pipe Type B: Dimensions dependent on the thickness of the thermoplastic liner.
80
100
125
25
40
50
65
32
50
25
32
40
180
165
245
140
T-piece D / E / N / B DN 25-250
T-pieces are glass fiber reinforced and are produced to DIN 16966 part 4 on the basis of UP and vinylester resins. Pipes of this type can be connected with laminated joints (see Pipe Joints) or flanges (see Fittings).
DN 1
175
DN 2
130
150
13025
L1
[mm]
C43
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
16
L2
[mm]
360
365
415
395
445
445
470
470
520
525
575
575
620
620
670
675
725
750
775
800
800
850
905800
900
L1
[mm]
525
600
680
830
950
1000
1250
1400
1500
700
400
500
350
300
350
400
350
600
700
800
700
400
500
600
500
600
Pipe Type B: Dimensions dependent on the thickness of the thermoplastic liner.
On request1100 - 4000
300
800
900
1000
500
600
700
350
400
300
250
300
DN 1
T-piece D / E / N / B DN 300-1000
T-pieces are glass fiber reinforced and are produced to DIN 16966 part 4 on the basis of UP and vinylester resins. Pipes of this type can be connected with laminated joints (see Pipe Joints) or flanges (see Fittings).
DN 2
150
200
250
200
250
C43
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
17
L1 L2 L3 L4
[mm] [mm] [mm] [mm]
180 85 20 20
205 40 40
200 20 20
235 65 60
230 85 45 45
205 25 25
260 85 80
235 85 65 60
210 40 40
275 105 100
245 85 75 75
210 40 35
325 130 125
285 110 90 85
250 50 50
350 155 150
310 110 115 110
285 65 60
375 180 175
350 110 130 125
310 65 60
495 255 245
430 127 195 185
370 130 125
575 320 310
510 143 255 245
400 130 125
150
125
150
200
80
100
125
100
125
65
80
65
80
100
200
250
DN 2
25
25
32
25
32
40
32
40
50
40
50
65
50
Pipe Type B: Dimensions dependent on the thickness of the thermoplastic liner.
Reducers D / E / N / B DN 25-250
Concentric reducers are glass fiber reinforced and produced to DIN 16966 part 5 on the basis of UP and vinylester resin. Pipes of this type can be connected with laminated joints (see Pipe Joints) or flanges (see Fittings).
85
80
100
125
150
DN 1
32
40
50
65
C44
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
18
L1 L2 L3 L4
[mm] [mm] [mm] [mm]
655 385 370
540 158 255 245
435 130 125
665 385 370
550 150 255 245
440 130 125
695 385 370
580 166 255 245
450 130 125
865 515 495
730 191 385 370
615 255 245
980 645 620
865 181 515 495
630 255 245
1160 775 740
930 197 515 495
660 255 245
1180 775 740
910 213 515 495
665 255 245
1185 775 740
945 230 515 495
700 255 245
1220 775 740
975 245 515 495
735 255 245
700
800
900
600
700
600
700
800
500
400
500
600
500
Pipe Type B: Dimensions dependent on the thickness of the thermoplastic liner. 0
350
400
500
600
700
800
900
1000
200
250
300
250
300
350
On request1100-4000
Reducers D / E / N / B DN 300-1000
Concentric reducers are glass fiber reinforced and produced to DIN 16966 part 5 on the basis of UP and vinylester resin. Pipes of this type can be connected with laminated joints (see Pipe Joints) or flanges (see Fittings).
DN 1
300
DN 2
150
200
250
300
350
400
350
400
C44
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
19
k b2
[mm] [mm]
16 115 85 14
16 140 100 15
16 150 110 16
16 165 125 18
10 185 145 20
10 200 160 22
10 220 180 24
10 250 210 27
10 285 240 30
6 340 295 33
6 395 350 37
6 445 400 42
4 505 460 40
4 565 515 44
4 670 620 49
2,5 780 725 49
2,5 895 840 53
2,5 1015 950 57
2,5 1115 1050 60
2,5 1230 1160 65
1100-4000
Fixed flanges are glass fiber reinforced and produced to DIN 16966, part 6, on the basis of UP and vinylester resin.
On request
80
40
50
65
800
900
1000
100
125
150
200
250
700
DN
25
32
Fixed Flange D / E / N / B
Screws
4 x M12
4 x M16
d2
[mm]
14
18
18
18
18
30
300
350
400
500
600
33
33
36
PN max D
22
22
26
26
30
18
18
22
22
22
18 4 x M16
4 x M16
4 x M16
8 x M16
8 x M16
8 x M16
8 x M20
8 x M20
12 x M20
12 x M20
24 x M30
28 x M30
28 x M33
16 x M20
16 x M24
20 x M24
20 x M27
24 x M27
C45
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
20
293
343
387
441
544
95
648
758
858
50
58
68
82
111
133
160
188
2376
6
6
4
4
4
68
78
88
102
122
370
430
482
585
138
158
188
212
268
320
16
16
16
1100-4000 On request
350
400
500
600
700
800
2,5
2,5
2,5
2,5
2,5
685
800
905
1005
1110 1060
960
57
60
64
300
25
32
40
50
65
80
100
125
150
200
250
16
10
10
10
10
10
900
1000
Stub Flange D / E / N / B
DN
Stub Flanges are glass fiber reinforced and produced to DIN 16966, part 6, on the basis of UP and vinylester resin.
d4
[mm]PN max
b3
[mm]
d5
[mm]
16
18
20
22
25
12
14
14
14
15
45
53
28
30
32
35
38
C46
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
21
Storage Tank
HOBAS produces process equipment up to a diameter of DN 4000. Thanks to the flexible production process, rectangular, round and asymmetric designs can be manufactured to the HOBAS Company Standards with almost no limitation to size. According to customer demands as well as special technical and operational requirements, even complex designs with GRP Composites Thermoplastics or pure GRP with a chemical protection layer can be developed.
D41
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
22
Absorber
The absorber or gas scrubber is a technical device that merges gas with a liquid in order to dissolve the components of the gas and absorb them with the liquid. It usually consists of several parts and reaction zones. HOBAS produces absorbers according to customer requirements, with chemically resistant GRP, with or without thermoplastic liner.
Example product: Flue gas scrubber, CMI-UVK GmbH Germany
D42
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
23
Cyclone
Cyclones are funnel-shaped and used for removing particles from a gas stream. Since the particles are continuously striking the inner cyclone walls, the material has to be especially abrasion resistant. Thanks to the excellent strength and chemical resistance of GRP, HOBAS Pipe Systems and Tanks are especially suited for this application. HOBAS produces customer-shaped cyclone systems with GRP or GRP Composites with thermoplastic liner.
Example product: Cyclone, Wacker Chemie AG Germany
D43
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
24
GRP Header
The term Header refers to storage tanks in the range of chemical process lines. The safe storage and transport of the highly aggressive reactive products of the chloralkali process – chlorine and caustic soda solution – calls for such chemically resistant tanks and pipe systems, which can withstand the process-related temperatures and pressures. HOBAS manufactures process equipment up to a diameter of DN 4000 and pressure classes up to PN 40 according to customer requirements. For particularly aggressive media, HOBAS Tanks and Pipes are provided with a thermoplastic liner.
Example product: Catholyte Header for chlorine electrolysis, UHDE GmbH Germany
D44
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
25
Pipe Spool Manufacture
Spools consists of various pipe components and accessories that are pre-assembled by HOBAS. Prefabricated spools help to save on costs and time at the installation of pipe systems and fully exploit the factory potentials for increasing quality standards. HOBAS produces spools in compliance with isometric plans, which are either provided by the customer or prepared by the HOBAS Engineers in accordance with the local requirements.
D45
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
26
D
[mm]
A B C D
95 34 - 28 14 4 x M12
105 40 - 38 34 4 x M12
115 48 / 50,5 36 45 42 4 x M12
140 60 46 55 51 4 x M16
150 68,5 52 66 62 4 x M16
165 82,5 65 / 69 78 78 4 x M16
185 95,5 77 / 82 92 92 4 x M16
200 111,5 94 108 111,5 8 x M16
220 133,5 119 128 / 135 133,5 8 x M16
250 160,5 149,5 158 167 8 x M16
285 188,5 173 178 188,5 8 x M20
340 238 225 235 - 8 x M20
395 294 280 288 / 294 - 12 x M20
445 344 329 338 - 12 x M20
505 388 370 376 - 16 x M20
565 442 415 430 / 456 - 16 x M24
670 545 515 533 - 20 x M24
780 645 618 633 - 20 x M24
A: for steel pipes with welded stub flange and GRP pipes (DIN 2673)
C: for PP/PE pipes with short welded stub flange (DIN 16962 / DIN 16963)
210
16
42
400
460
515
350
18
20
22
24
27
30
32295
36
38
SMC Loose Backing Ring
DN
25
32
Loose backing rings are produced by HOBAS as SMC (Sheet Moulding Compound) parts to DIN 16966, part 6. Fitting dimensions for PN 10 flanges to DIN 2501, part 1.
14
18
Screws
d2 b
14
PN max
k
85
100 15
15
Other diameters and pressure classes on request.
d1
10
10
10
6
6
6
4
4
4
26
26
18100
22
22
725
500
150
200
250
300
350
40
50
34
25 14 65 14
B: for steel flange pipes with welded stub flange (DIN 2542)
D: for PVC pipes with stub flange (DIN 8063)
400
240
65
80
22
620
18
22
22
47
110
124
145
160
180
[mm] [mm] [mm] [mm]
51
14 75 1420 20
600 2,5 30
18
16
16
16
16
10
10
18
18
18
125
E41
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
27
d4 [mm]
d5 [mm]
d8 [mm]
b [mm]
h2 [mm]
Rohrtyp Rohrtyp Rohrtyp Rohrtyp
D, E, N B D, E, N B
16 - 25 45 33 15 20 29 8 28
16 - 30 58 39 20 25 36 10 30
16 30,5 37 68 50 25 32 45 12 34*
16 37,4 45 78 58 32 40 53 14 32
16 45,6 55 88 68 40 50 64 14 38*
16 57 68 102 82 50 63 77 14 45*
10 70 80 122 95 65 75 90 15 48*
10 85,9 95 138 111 80 90 106 16 52*
10 106 114,5 158 133 100 110 127 18 60*
10 129,5 129,5 188 160 125 125 142 20 70*
10 155,8 165,5 212 188 150 160 180 22 76*
6 204,5 204,5 268 237 200 200 220 25 85
6 254,5 254,5 320 293 250 250 270 28 101
6 304,5 319,5 370 343 300 315 338 30 116
4 359 359 430 387 350 355 380 32 133
4 405 405 482 441 400 400 428 35 147
4 506 506 585 544 500 500 532 38 178
* Deviations from DIN 16966, part 6
Stub flanges are produced by HOBAS as SMC (Sheet Moulding Compund) parts to DIN 16966, part 6.
d3 [mm]
500
150
200
250
300
350
400
20
15
Other diameters and pressure classes on request.
d6 [mm]
125
SMC Stub Flange
DN
25
32
40
50
65
80
100
PN max
E42
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
28
D d2 k
[mm] [mm] [mm]
10 95 14 65 4 x M12
10 105 14 75 4 x M12
10 115 14 85 4 x M12
10 140 18 100 4 x M16
10 150 18 110 4 x M16
10 165 18 124 4 x M16
10 185 18 145 4 x M16
10 200 18 160 8 x M16
10 220 18 180 8 x M16
10 250 18 210 8 x M16
10 285 22 240 8 x M20
6 340 22 295 8 x M20
6 395 22 350 12 x M20
6 445 22 400 12 x M20
4 505 22 460 16 x M20
4 565 26 515 16 x M24
4 670 26 620 20 x M24
Other diameters and pressure classes on request.
Blind flanges are produced by HOBAS as SMC (Sheet Moulding Compound) parts to DIN 16966, part 6. Fitting dimensions for PN 10 flanges to DIN 2501, part 1.
32
34
36
16
18
20
PN max
15
20
14
14
38
SMC Blind Flange
Screws
25
32
b
[mm]
14
15
DN
40
50
65
47
22
24
27
350
400
500
250
300
42
100
125
150
200
80
30
E43
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
29
Material Specifications
According to requirements and design, HOBAS Industrial Pipe Systems are characterized by the following data (further details on request):
Physical properties
8000 - 20.000 N/mm²Flexural elastic modulus
1,5 bis 2,0 g/cm³
25-65 % vol.
80 - 360 N/mm²Glass content
Density
Tensile strength (tengential) 80 - 200 N/mm²Tensile strength (axial)
20 - 30 x 10-6 1/KMean linear thermal expansion coefficient0,25 - 0,35
105
0,25 W/mKThermal conductivity
> 200 °CHeat deflection temperature
Surface resistance (electrically conductive)
Poisson's ratio
Points of reference for different pipe types up to 50 °C
1012 Surface resistance (standard)
F41
All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express orimplied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice.
30
We develop and manufacture HOBAS Products conserving nature‘s resources and with respect for our environment. Visit our website to find out more about the HOBAS Environmental Policy.
HOBAS Group WorldwideHOBAS manufactures and markets HOBAS GRP PipeSystems. The HOBAS Network includes HOBAS Pro-duction Facilities and Sales Organizations in Europe and throughout the world.
HOBAS Engineering AustriaPischeldorfer Straße 128 9020 Klagenfurt | Austria
T +43.463.48 24 24F +43.463.48 21 21