Page 1 of 18939500487 Rev D

Privacy Wall Slider Door

#2 ACR BIT

3/16" HEX BIT

RAYBO

5/32DRILL BIT

5/64 HEX

1"�OPEN END�WRENCH

PLUMB BOB

Full Glass Four Equal Divided Lites Two Transom-Aligned Lites

If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.

(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2008 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.

Printed in U.S.A.

®

LOCTITE 425®

Four Transom-Aligned Lites Three Equal Divided Lites

Page 2 of 18939500487 Rev D

ComponentsSLIDING DOOR

SLIDING DOOR GUIDE ASSY &�#8-32 x 1/4" PAN HD TAP SCREWS

SLIDING DOOR TRACK,�SLIDER TRACK FASCIA ASSY,�BUMPER STOP ASSY'S,�#10-16 x 3/4" SELF DRILL PH SCREWS,�1/4-20 x 1/2" HEX HD TAP SCREWS�& 1/4-20 NUTS

HANGER KIT ASSY WITH�SCREWS INCLUDED IN �HARDWARE BAG

LOCK KIT CONSISTING OF:�SLIDING DOOR HANDLE ASSY,�ADAMS RITE LOCK,�KEY MORTISE�CYLINDER &�1-1/8" THUMB�TURN LEVER

(1) NON-LOCKING�& (1) LOCKING�DOOR STOP�CHANNEL ASSY

SLIDING DOOR�FRAME�CHANNEL

SLIDING DOOR CHANNEL,�FINISHED END CAP ASSY &�#10-16 x 1-1/2" PH TAP SCREWS�

SINGLE STRIKE SLIDER PLINTH TRIMS,�SLIDER STRIKE PLINTH TRIM &�#8-18 x 1/2" UNDERCUT FLAT HEAD TAP SCREWS�

CLAMP CHANNEL &�#10-16 x 1-1/2" PH TAP SCREWS

DOUBLE STRIKE�SLIDER PLINTH &�#8-18 x 1/2"�UNDERCUT FLAT�HEAD TAP SCREWS�

BACK-TO-BACK�SLIDING DOOR COVER

®

Page 3 of 18939500487 Rev D

1. Install the fixed panel up into the ceiling track.

2. Build the finished frame using a clamp channel and four (4) #10-16 x 1-1/2" pan head tapping screws.

2a

SLIDING DOOR�FRAME CHANNEL

SLIDER DOOR�CHANNEL

2d

2e

2c

#10-16 x 1-1/2" PAN�HEAD TAPPING SCREW

2b

CLAMP CHANNEL

®

Page 4 of 18939500487 Rev D

3

3. Install the finished frame into the opening between the fixed frame and the Pathways Privacy Wall.

®

Page 5 of 18939500487 Rev D

4. Level the panels and finished frame checking.

4a

4f

4e

4d

4c

4b

®

Page 6 of 18939500487 Rev D

5. Checking for plumb and squareness.

5a

5b

5c

®

Page 7 of 18939500487 Rev D

6. Install the feature strips and lock the frame to the fixed panel and the Pathways Privacy Wall.

6a6c

FEATURE STRIP

NOTE: Optional application�for noise sensitive areas.

6b

®

Page 8 of 18939500487 Rev D

7. Install the sliding door track (7a). The sliding door track has two notches (7b) this is so the track is non-handed. Place the track in the top horizontals and lock into place with four (4) #10-16 x 3/4" self drilling pan head screws.

7a

7b

7c

NOTCHES

#10-16 x 3/4" SELF DRILLING�PAN HEAD SCREW

SLIDING DOOR TRACK

®

FOAM

Page 9 of 18939500487 Rev D

8. Install slider door guide assembly components together per the correct handing (8a). Install the slider door guide assembly onto the door stop channel assembly next to the fixed panel on the door side of the frame (8b). Support the slider door guide assembly temporarily with foam (8c). Install with (2) two #8-32 x 1/4" pan head tapping screws (8d).

8b

8c

#8-32 x 1/4" PAN HEAD�TAPPING SCREW

8d

DOOR STOP�CHANNEL ASSEMBLY

8a

®

SLIDER DOOR�GUIDE ASSEMBLY

Page 10 of 18939500487 Rev D

9. Install the bumper stop assemblies loosely and the hanger kit assemblies (wheel portion) into the sliding door track (9a). Mount the hanger kit assembly (bracket) on top of the sliding door (9b) with screws that are provided with the hanger kit.

9b

SCREW

9a

BUMPER STOP�ASSEMBLY

HANGER KIT�ASSEMBLY�

(WHEEL)

HANGER KIT�ASSEMBLY�(BRACKET)

®

10a

Page 11 of 18939500487 Rev D

10b

BUMPER�STOP�ASSEMBLY

GUIDE ASSEMBLY

10. Position the bottom of the sliding door on the guide assembly (10a) and tilt the top up. Next, engage the sliding door onto the hanger kit then lock the hanger kit in place (10b). Now adjust the hanger kit up or down to align sliding door, frame and panels. Adjust the bumper stop assemblies (10c).

10c

®

FASCIA

Page 12 of 18939500487 Rev D

11a

11b

11c

11. There are two sets of holes on the door track. Place the fascia on top of the door track to see which holes are used for your installation.

Install the 1/4-20 x 1/2" hex head tapping screws up from bottom side and add the 1/4-20 nuts to the top side of the door track (11a) loosely, leaving room to slide the fascia between the track and the nuts. Position the fascia (11b) and tighten the nuts (11c).

®

Page 13 of 18939500487 Rev D

12. Install collar, lock washer and screw onto the handle that has threads inside the tubes as shown (12a). Place the handle with the clearance hole inside the tubes over the screw head and collar (12b). Install the set screws on the upper and lower portion of the handle using Loctite 425 (12c).��NOTE: Make sure the set screws are located on the bottom of the handle, so they are not visible to the user. ��Insert the lock body into the sliding door frame and start screws to hole lock loosely. Install key and thumb cylinder. Lock cylinders in place with set screws then tighten lock body screws check lock, key and thumb and adjust after complete. Place the trim around lock bodies (12d).

HANDLE�(WITH THREADS�INSIDE TUBES)

COLLAR

LOCK WASHER

SCREWHANDLE�

(WITH CLEARANCE�HOLE INSIDE TUBES)

SET SCREW

3/32" ALLEN�WRENCH

12a12b

12c

12d

®

FOR FIELD INSTALLED HANDLE OPTION

DOOR VERTICAL

5/8"

5/8"

Locate handle mounting holes in this zone.

Page 14 of 18939500487 Rev D

13. Mount the single strike slider plinth trim with a #8-18 x 1/2" undercut flat head tap screw as shown, making sure the base trim mounts with clean lines.��

14. Mount the single strike slider plinth trim and the slider strike plinth trim with two (2) #8-18 x 1/2" undercut flat head tap screw as shown, making sure all the trims mount with clean lines.

13

SINGLE STRIKE�SLIDER PLINTH TRIM

SINGLE STRIKE�SLIDER PLINTH TRIM

SLIDER STRIKE�PLINTH TRIM

14

PATHWAYS PRIVACY WALL

PATHWAYS PRIVACY WALL�SLIDING DOOR FRAME

PATHWAYS PRIVACY�WALL SLIDING DOOR

NOTE: This view is shown�turned 90 degrees for clarity.

NOTE: This view is shown�turned 90 degrees for clarity.

®

Page 15 of 18939500487 Rev D

15. Use an awl and scribe down inside the step of the plinth trim (15a & 15c) and then take a pair of pliers and snap the thin metal step off the trim (15b & 15d).�

�16. Mount the two (2) single strike slider plinth trims with two (2) #8-18 x 1/2" undercut flat head tap screws as shown.��

17. Mount the two (2) slider strike plinth trims with two (2) #8-18 x 1/2" undercut flat head tap screws as shown.

15a

15c

15b

15d17

16

BACK-TO-BACK�PATHWAYS PRIVACY WALL�

SLIDING DOOR FRAMES

SINGLE STRIKE�SLIDER PLINTH TRIMS

SLIDER STRIKE�PLINTH TRIMS

SINGLE STRIKE�SLIDER PLINTH TRIM

SLIDER STRIKE�PLINTH TRIM

NOTE: This view is shown�turned 90 degrees for clarity.

®

Page 16 of 18939500487 Rev D

Optional Back-to-Back Cover�(Inline Application)��

1. Use an awl and scribe down inside the step of the single strike slider plinth trim (15c on previous page) and then take a pair of pliers and snap the thin metal step off the trim (15d on previous page). Two (2) single slider plinth trims are required for this installation.��

2. Slide the double strike sliding door plinth trim over the back-to-back pathways privacy wall sliding door frames and secure with two (2) #8-18 x 1/2" undercut flat head tap screws (2a). Slide the back-to-back slider cover over the frames and on top of the plinth trim and snap into position (2b).��

3. Install the two (2) single strike slider plinth trims with #8-18 x 1/2" undercut flat head tap screws as shown.

3

2b

BACK-TO-BACK�PATHWAYS PRIVACY WALL�SLIDING DOOR FRAMES

SINGLE STRIKE�SLIDER PLINTH TRIMS

BACK-TO-BACK�SLIDER COVER

DOUBLE STRIKE SLIDING�DOOR PLINTH TRIM

2a

NOTE: This view is shown�turned 90 degrees for clarity.

®

Page 17 of 18939500487 Rev D

= Inline Feature Strip

= Half Feature Strip

CL

CL

CL

CL

1.341" �(1-11/32")

~~

1.341" �(1-11/32")

~~

Sliding Door

Sliding Door Sliding Door

Optional Connection Conditions

NOTE: All other connection conditions�are the same as standard panel�mounting connection conditions.

"T" with Two (2) Sliding Doors Centered

90 with Centered Panel�with a Sliding Dooro

®

Page 18 of 18939500487 Rev D

Optional Plinth and Base Trim Connection Conditions

"T" with Two (2) Sliding Doors Centered

90 with Centered Panel�with a Sliding Door

Sliding Door

Sliding Door

Sliding Door

NOTE: All other plinth and base trim�connection conditions are the same�as standard panel mounting plinth�and base trim connection conditions.

Steps removed�on both plinths

SINGLE STRIKE�SLIDER PLINTH

SLIDER STRIKE�PLINTH

BASE TRIM

BASE TRIM

Step removed�on plinth

CL

Steps removed�on both plinths

Step removed�on plinth

Step removed�on plinth

SLIDER STRIKE�PLINTH

SLIDER STRIKE�PLINTH

CL

"T" with a Sliding Door Centered

Sliding Door

Step removed�on plinth

SLIDER STRIKE�PLINTH

CLCORNER�BASE TRIM

BASE TRIM

BASE TRIMBASE TRIM

Factory edge�of base trim

Factory edge�of base trim

Factory edge�of base trim

Factory edge�of base trim

BASE TRIM

o

®