forward roller · product. rite way manufacturing co. ltd. p.o. box 328 imperial, saskatchewan,...

1

Forward Roller

Table of Contents

Forward Land Roller

SECTION PAGE

INTRODUCTION & MANUAL INFORMATION 2-3

PRE-DELIVERY INSPECTION / NOTES 4-5

SPECIFICATIONS 6-9

SERVICE AND WARRANTY INFORMATION 10-11

SAFETY SUGGESTIONS 12-13

DECAL LOCATIONS 14-15

MAINTENANCE / GREASE LOCATIONS 16-19

OPERATING NSTRUCTIONS 20-25

ASSEMBLY INSTRUCTIONS 26-33

DRUM END CAP ASSEMBLY 34-35

FINISH ROLLER ASSEMBLY 36-37

HITCH ASSEMBLY 38-39

HITCH ASSEMBLY CENTRE FRAME SWING ARM LOCK UP ASSEMBLY 40-41

TELESCOPIC SWING ARM ASSEMBLY 42-43

DRAFT ARM / TELESCOPIC SWING ARM ASSEMBLY 44-45

WALKING ARM AND CENTRE AXLE ASSEMBLY 46-47

INNER / OUTER WING ASSEMBLY 48-49

OUTER WING ASSEMBLY 50-51

WING AXLE ASSEMBLY 52-53

WING TRANSPORT TIE BAR ASSEMBLY 54-55

PERFECT HITCH ASSEMBLY 56

WING LIST, ALL MACHINES AND SIZES 57

HOSE CLAMP SCHEMATIC 58

CTD 812 SERIES HUB BREAKDOWN 59

20" 3000 lbs. SIDE WIND PARKING JACK 60

ACRE METER PLACEMENT 61

MONARCH HYDRAULIC CYLINDER 62-65

LIGHT KIT LOCATION 66-67

4-BOLT FLANGED BEARINGS INSTALLATION 68

NOTES 69

GRADE CHART 70

TORQUE CHART 71

HYDRAULIC SCHEMATIC 72-75

OVER VIEW OF ALL MODELS 76-85

2

Forward Roller

Introduction

We are pleased to welcome you as an owner of a product from

RITE WAY MFG. This product is the result of years of agricultural and engineering experience, and is built to give you many years

of successful operating service.

For the best efficiency and smoothest operation of your Forward Fold Roller, we have provided this Owners Manual. Its prepara-

tion is the result of years of experience gained in field testing and normal usage of this and similar implements. We urge you to

carefully study this manual so that it will give you a thorough un-derstanding of your Forward Fold Roller before operation. We

also urge your care of this manual so that it will be available for future reference when needed. If your manual should be lost,

damaged or destroyed, a new copy can be purchased from your RITE WAY MFG. dealer. We will also be happy to answer any

questions that you might have regarding the use or care of this

product.

Rite Way Manufacturing Co. Ltd. P.O. Box 328

Imperial, Saskatchewan, Canada S0G 2J0

PH: 306-963-2180 Fax: 306-963-2660

Web Site: www.ritewaymfg.com Email: [email protected]

Thank you for making the decision to purchase a RITE WAY

3

Forward Roller

Manual Details

Unit Model Number FFS (Forward Fold Series)

Manual Revision Number Revision 1.1

Manual Revision Date February / 2016

Manual Serial Number Range Serial # 16-2492 to Current

Previous Serial Number Range Serial # 15-2173 to 15-2491

Owner / Equipment Information

Serial Number of Unit

Date of Purchase

Dealer Name

Dealer Address

Dealer Phone Number

Salesman Name

Salesman Phone Number

Notes

The area below is provided for the owner / end-user to make notes regarding the equipment.

Manual Information

4

Forward Roller

Pre-delivery Inspection Check List

Delivery

Verify that ‘The customer is aware of warning decals and proper jack placement for transport.’.

Verify that ‘The customer is aware of proper operation and transportation of the unit’.

Verify that ‘The customer has received an operators manual’.

Explain all maintenance and service intervals to the customer (From operators manual).

Advise the customer of grease zerk locations and maintenance schedules.

Level the unit per operators manual and instruct the customer on the proper procedures.

Please attach this Pre-Delivery Inspection Check Sheet to Warranty Registration Form.

Pre-delivery Inspection Check List

Date: Signature of Technician who performed the inspection

General

Remove wrapping and wash unit, removing all road debris. (Road salt, mud, snow, etc.)

Inspect paint, decals and general appearance of unit.

Verify that the owners manual is in the manual storage tube.

Verify ‘SLOW MOVING VEHICLE’ sign (SMV) is on unit (if applicable)

Verify that jacks are with the unit and function properly.

Check wheel bolts for proper torque, proper wheel size and all tires are the same make

Check for proper tire pressure (PSI).

Verify that the wheel hubs are lubricated.

Verify that locking pins and / or ram locks are in place.

Lubricate all components as per operators manual recommendation.

Check that all bolts and fasteners are at the proper torque specifications.

(NOTE: All cap screws that have lock nuts join moving pieces should not be tightened completely, they must allow movement. i.e. Spring pressure kits, rock shaft connector, draft arm, etc.

Check sprocket alignment and chain tension. (If applicable)

Check locking collars and set screws for proper torque. (If applicable)

Verify operation of lights. (If applicable)

Verify the unit moves ‘IN’ and ‘OUT’ of transport without any binding.

Hydraulics

Insure that all hydraulic hoses and lines are routed properly and secured.

Verify that all hydraulic fittings / hoses are secure and there are no oil leaks.

Inspect all cylinders for leakage and the cylinder shaft for rust, pits, or scratches.

Verify operation of all hydraulic functions - Cycle hydraulic cylinders to remove air from the system.

5

Forward Roller

Notes

6

Forward Roller

Specifications

Dimensions (Approximate) F3 Series

Unit Size 32’ 36’ 42’ 46’ 52’ 34’ 40’ 50’ 44’

Working Width 31’4” 35’4” 41’7” 45’4” 51’4” 33’4” 39’7” 49’4” 43’4”

Transport Length 40’ 41’10” 45’1” 46’10” 50’ 41’10” 45’1” 50’ 46’10”

Transport Width 15’ 14’ 14’ 14’ 14’ 12’ 12’ 12’ 12’

Weight (lbs) 19,600 20,900 22,800 23,800 25,300 19,200 21,300 24,000 22,100

Center Section 12’ 12’ 12’ 12’ 12’ 10’ 10’ 10’ 10’

Wing Section #1 10’ 12’ 15’2” 17’ 20’ 12’ 15’2” 20’ 17’

Draft Arms 108

1/2”

153

7/8”

161

1/2”

161

1/2”

171

1/8”

153

7/8”

161

1/2”

171

1/8”

161

1/2”

Specifications—3 Section (F3)

General Information 3 Section Roller: Center Section + Left and Right Wings

Heavy Duty drum roller.

FORWARD™ unfold and folding system.

Rigid Draft arm system

7

Forward Roller

Specifications


General Information 5 Section Roller: 1 Center Section + Inner Wings Left & Right + Outer Wings Left & Right

Finishing Rollers provide overlap to rear of Inner & Outer Wing sections.

Heavy Duty drum roller




Unit Size 46’ 50’ 54’ 62’ 68’ 58’ 74’ 78’ 84’

Working Width 45’9” 49’9” 53’9” 61’9” 67’11” 57’9” 74’3” 77’11” 83’11”

Transport Length 47’2” 49’2” 51’3” 55’2” 61’5” 53’2” 64’5” 66’5” 69’5”

Transport Width 14’ 14’ 14’ 14’ 14’ 14’ 14’ 14’ 14’

Weight (lbs) 26,500 28,100 29,400 32,000 34,400 30,500 35,900 37,000 38,800

Center Section 12’ 12’ 12’ 12’ 12’ 12’ 12’ 12’ 12’

Wing Section #1 8’ 8’ 10’ 12’ 12’ 10’ 15’-2” 17’ 20’

Wing Section #2 8’ 10’ 10’ 12’ 15’2” 12’ 15’2” 15’2” 15’2”

Draft Arms 171

1/8”

171

1/8”

171

1/8”

237

3/8”

237

3/8”

237

3/8”

237

3/8”HD

237

3/8”HD

237

3/8”HD

8

Forward Roller

Specifications


General Information 5 Section Roller: 1 Center Section + Inner Wings Left & Right + Center Wings Left &Right + Outer

Wings Left & Right

Finishing Rollers provide overlap to rear of Inner & Center & Outer Wing sections.

Heavy Duty drum roller




Unit Size 65’ 69’ 81’ 85’ 89’ 77’ 73’

Working Width 64’8” 68’3” 80’5” 84’5” 88’5” 76’5” 72’4”

Transport Length 59’6” 61’5” 67’5” 69’6” 71’7” 65’5” 63’5”

Transport Width 14’ 14’ 14’ 14’ 14’ 14’ 14’

Weight (lbs) 34,700 36,000 40,800 42,100 43,300 35,600 34,400

Center Section 12’ 12’ 12’ 12’ 12’ 12’ 12’

Wing Section #1 8’ 8’ 10’ 10’ 12’ 8’ 8’

Wing Section #2 8’ 8’ 10’ 12’ 12’ 10’ 10’

Wing Section #3 8’ 10’ 12’ 12’ 12’ 12’ 10’

Draft Arms 171 1/8” 171 1/8” 237 3/8”

HD

237 3/8”

HD

237 3/8”

HD 171 1/8” 171 1/8”

9

Forward Roller

Specifications

Specifications

Options Available Acre Meter Kit

Clevis Hitch Kit

Scraper kit

10

Forward Roller

Service & Warranty Policy


Rite Way Manufacturing Co. Ltd. (hereafter referred to as Rite way) warrants each new machine to be

free from defects in materials and workmanship for a period of one (1) year from date of purchase

under normal agricultural use and service. In addition, Rite Way will supply at no charge, (F.O.B Rite

Way Factory) any part that has failed within the 2nd year. Rite Way’s obligation under this warranty is

limited to the repair or replacement of any defective parts of the equipment at its own discretion.

Any alterations, modifications or additions done to a finished product will void this war-

ranty unless prior written permission from Rite Way is obtained.

Items that are not manufactured by Rite Way are covered by the warranty of the supplier of

these items. We will therefore extend, without assuming any responsibility, any warranty given to us

by our suppliers.

This warranty shall-not apply to any machine, that in the company’s judgment has be subject-

ed to misuse, negligence or accident. In no event shall the owner be entitled to recover costs for inci-

dental, special or consequential damages such as, but not limited to; Loss of crop, loss of profit or

revenue, other commercial losses, inconvenience or rental costs.

This warranty shall not apply unless Rite Way or its designated dealer is promptly notified of

claimed defects and the allegedly defective part is held for inspection.

Repair parts purchased for machines ‘Out of Warranty’, are warranted to be free from defects

in material and workmanship under normal use and service for a period of ninety (90) days from the

date of delivery to the customer.

The warranty shall only become valid when delivery notification for warranty is received by

Rite Way within 20 days of the completion of sale.

OWNER’S / USERS OBLIGATION: It is the responsibility of the user to read the Operators Manual

and understand the safe and correct operating procedures as it pertains to the operation of the prod-

uct, and to lubricate and maintain the product according to the maintenance schedule in the Manual.

The user is responsible for inspecting the machine, and for having parts repaired or replaced

when continued use of the product could cause damage or excessive wear to any other parts. It is the

user’s responsibility to deliver their machine to a Rite Way dealer for service or replacement of defec-

tive parts which are covered by the standard warranty.

Rite Way will not by held responsible for charges such as transportation, fuel, lodging when a

dealer / dealer representative travels to a customer location for warranty or inspection.

11

Forward Roller


1. All claims must be handled through a dealer / distributor. All claims must be submit-

ted on a properly completed warranty claim form within 30 days of the date of repair.

2. A warranty registration claim form must be on file at Rite Way Mfg. to validate a war-

ranty claim.

3. Defective parts are to be held at the dealer / distributor’s place of business until the

warranty claim form has been processed. Rite Way will advise when parts can be

released.

4. Parts that require inspection by Rite Way personnel must be accompanied by a Re-

turn Goods Form number, and must be sent by pre-paid freight. Rite Way will refund

pre-paid freight charges on any items determined to be defective.

5. Rite Way will not assume responsibility for repairs or expenses incurred without au-

thorization. Warranty labour in excess of $150.00 must be authorized before such

work is performed and photographs before and after repairs are required.

6. Warranty labour is to be claimed on the warranty claim form, only if the warranty la-

bour was performed by the dealer. Travel time is not covered by warranty and

should not be included. Rite Way reserves the right to adjust or allocate labour times

and values based on its experience.

7. It is the responsibility of the dealer to ensure that the warranty registration forms are

properly completed and returned to Rite Way Mfg., Imperial, SK.

Service & Warranty Claim Procedure

12

Forward Roller

Safety Warnings

1. Read the manual thoroughly and understand before operating or work-

ing on the machine.

2. Study all safety and warning decals on the implement.

3. Most accidents occur because of neglect or carelessness.

4. Do not allow riders on the tractor or implement during operation.

5. Do not allow children on or near the machine.

6. Connect the implement hitch to the tractor before operating the hydrau-

lic system.

NOTE: Be aware of any hydraulic leaks.

7. Always throttle the tractor down and use caution when connecting the

implement to the tractor hitch.

NOTE: Never stand between the tractor and implement.

8. Lower the hitch jack onto firm ground and chock the tires when un-

hooking implement from tractor.

NOTE: Ensure the unit is on level ground prior to un hooking

tractor.

9. Exercise extra caution when working on hillsides or near ditches.

10.Ensure that the tractor draw-bar is pinned during transport.

11.Maximum speed while transporting the Unit is 18 mph (29 km).

12.Do not work on this machine when hydraulic system is under pressure.

Safety Warnings (General)

This machine will provide years of trouble-free & safe opera-tion IF all maintenance and safety instructions are followed.

13

Forward Roller

1. Ensure that the Roller is lowered to the ground before doing

any work on machine.

NOTE: If it is necessary to work on machine with the

Roller drums raised, ensure that cylinders are locked in

position.

2. Do not work on this machine when hydraulic system is under

pressure.

3. Observe all laws and regulations when transporting unit on

public roads.

4. Do not transport this machine on public roads unless all safety

& maintenance checks have been completed.

5. Ensure that safety chains are in place prior to transporting.

6. Ensure that all transport lock pins are secured in place prior to

transport.

7. DO NOT lower unit in transport position or swing arm /

draft arm damage will occur.

Safety Warnings (Equipment Specific)

Safety Warnings

14

Forward Roller

Decal Locations

Decals

11

8 8

2, 3, 5, 7,

9, 10

11

1,6,8,12 1,8,12

1,8

1

1

1,8

1

1

4,8,12 4,8,12

11

1111

1515

15

Forward Roller

Decals

Item # Description Qty Part #

1 Amber Reflector (3 x 2) 16 060-0009

2 Caution - Escaping Fluid Hazard... 1 060-0011

3 Important - Block Wheels... 2 060-0015

4 Red Reflector (3 x 2) 4 060-0022

5 Warning - Lower or Block Elevated... 2 060-0028

6 Riteway Serial Number Plate 1 060-0034

7 Attention - Insure That All Cylinders Are Retracted... 1 060-0038

8 Grease Every 8 Hours 1 060-0046

9 1 Important - Hydraulic Hose Application (Three Color) 060-0061

10 1 Warning - Check And Tighten Hub... 060-0067

11 2 Riteway Mfg. (Large Decal, 31 x 5 - White) 060-0072

12 1 Riteway Mfg. (Small Decal, 9 x 4 - White) 060-0092

13 2 R (Load Jobs Only) as required 060-0032

14 2 L (Load Jobs Only) as required 060-0033

15 2 Warning—Turns of more than 45º…. 060-0095

UNIT SERIES UNIT SIZE MODEL YEAR UNIT NUMBER

FFS-52 16-0001

16

Forward Roller

Maintenance

General

Repack the wheel hubs after the first 500 travel miles; then yearly thereafter.

Visually inspect the wheel bolts for tightness each day. Riteway torque recommen-

dation to 110 ft - lbs after the first few hours of operation and frequently there after,

(manufactures torque recommendations 90 to 131 ft - lbs).

Requires 3-1/2 to 4-1/2 HP per foot.

Every 8 Hours (Daily)

Grease all pins and knuckles. (See page 18 for detailed diagram).

Every 100 Hours (Monthly)

Visually inspect hydraulic hoses & fittings for leaks or damage.

Inspect lighting system and electrical harness for damage

Annually

Inspect wheel bearings / hubs and grease.

Check wheel bolts and re-torque.

Check tire pressure, follow tire manufactures inflation recommendations.

Visually inspect unit for loose, worn or damaged components.

Maintenance

17

Forward Roller

Maintenance

Storage

Coat any exposed cylinder shafts with thick oil or grease.

Ensure that parking jacks are situated on firm ground.

NOTE: If jack pads sink into ground, it will be difficult to hook up unit.

Lock all applicable safety pins into place.

NOTE: All fasteners with locknuts that are used to join moving pieces should not

be tightened completely, to allow for movement.

Rockshaft connector cap screws;

Finish Roller Drum Mount Connection, Page 36, Items 12 & 15

Centre Axle Upper Link Connection, Page 46, Items 21 & 24

Maintenance

18

Forward Roller

Maintenance

Grease Locations

Maintenance

EVERY 8 HRS

EVERY 8 HRS

EVERY 8 HRS

EVERY 8 HRS

19

Forward Roller

Maintenance

Maintenance

20

Forward Roller

Operating Instructions

General Information

NOTE: Always choose a level area when folding unit either into or from transport

position.

NOTE: Lubricate all pins, axles and bearings regularly to prevent premature fail-

ure of components. (See page 18 for lubrication diagram).

Tractor Hook-Up

Move tractor into position where pin can be dropped into place through draw bar hitch.

NOTE: Use a clevis type tractor hitch with a retained type of hitch pin.

Retract parking jack and secure in transport position prior to moving the machine.

NOTE: Ensure that parking jack handle is secured by chain prior to moving the

machine (Failure to do so may damage the jack handle).

NOTE: Clean hydraulic hose ends prior to coupling with tractor hydraulic system.

Tractor Disconnecting

Ensure that the roller sections are either; Fully raised in transport position, or Fully lowered

into field position.

NOTE: If the Roller is in transport position, ensure that all lock pins are in place.

Chock block all tires front and back before disconnecting from the tractor.

NOTE: Failure to properly block unit may result in damage or injury. Negative

hitch weight may result if tires are not blocked properly in position.

Lower parking jack (s) into position, lowering until roller hitch is raised off of the tractor clev-

is.

NOTE: Ensure that the jack is placed on firm ground prior to un hooking.

Cornering Field Work

During field operation, always make turns so that the inside wing drum continues to rotate.

Sharp turns will increase the stress applied to the auto-fold system & inside wing drum and

may cause damage to the unit.


21

Forward Roller


Transport to Field Position

1. When entering the field from transport, find a location that is as level as possible and stop the

tractor / roller.

2. Remove all wing axle safety lock pins and tee lock pins.

3. While moving forward in low gear, feather wing axle wheels by activating the hydraulic steer-

ing cylinders to maximum angle (approximately 45 degrees) - the slow moving sign will indi-

cate the position.

4. Continue to drive forward slowly, wings will open to about 45 degrees, Stop.

5. Feather wing axle wheels back to straight (transport) position while backing up.

6. Continue to back up until the draft arms / swing arms move into the cam lock sockets.

7. Activate the hydraulics to lower the unit (roller drums) to the ground, hold hydraulic lever until

the wing axles are fully raised.

NOTE: Ensure that all wing transport locks are fully open and draft arm lock is fully

closed.

Operating Instructions cont -

22

Forward Roller


Field to Transport Position (All models)

1. Bring unit to a complete stop in a level area of the field.

2. Use hydraulic system to raise drums / lower wing axle & walking axle.

NOTE: Ensure that all wing cam locks are fully engaged.

NOTE: Ensure that draft arm locks are fully retracted / released.

3. Slowly drive forward until wings have moved into transport position.

4. Replace all safety lock pins and tee lock pins.

5. Unit is ready for road transport.

NOTE: Ensure safety chains are properly attached to tractor and lighting system

has been activated.


23

Forward Roller


Setting wing lock cylinder

1. Cycle hydraulic system to ensure all air has been purged.

2. With unit in transport position, inspect wing cam lock—look for space between hook and

cam roller.

3. If hook is not in contact with cam roller—adjust the cylinder clevis.

4. A) Remove cylinder clevis pin.

B) Loosen cylinder clevis lock screw.

C) Turn cylinder clevis CCW 1/2 to 1 turn.

D) Re-install cylinder clevis to wing lock.


Check for space here;

- If hook is in contact with cam roller

then cylinder setting is OK.

- If you can see a space then cylinder

requires setting. Adjust cylinder clevis as necessary

24

Forward Roller



Setting center frame lock cylinder

1. Cycle hydraulic system to ensure all air has been purged.

2. With unit in transport position, inspect wing cam lock—look for space between hook and

cam roller.

3. If hook is not in contact with cam roller—adjust the cylinder clevis.

4. A) Remove cylinder clevis pin.

B) Loosen cylinder clevis lock screw.

C) Turn cylinder clevis CCW 1/2 to 1 turn.

D) Re-install cylinder clevis to wing lock.

Check for space here when latch is engaged

- If hook is in contact with cam roller then cylinder

setting is OK.

- If you can see a space then cylinder requires setting.

Adjust cylinder clevis as necessary

25

Forward Roller


Setting Wing Axle Steering Toe—In / Out

NOTE: Steering Axle adjustment is necessary if roller does not properly follow the

tow vehicle when in transport position. Adjustment must be made to left and right axles.

1. With unit in transport position, inspect the wing axle steering. With hydraulic steering cylin-

der set to transport position (fully retracted), the tires must be aligned with a very slight

toe—out (approximately 1/2 to 1 degree). The front center line of the tire should be wider

than the rear center line by approximately 1/2”.

2. After adjustment, the unit should be transported a short distance to ensure that it trails

properly.


Check with cylinder fully collapsed

1/2 to 1 degree of toe-out

26

Forward Roller

Assembly Instructions


Drum End Cap Assembly

1. Reference to “left” or “right” and “forward” or “rear” are always determined from the rear of the ma-

chine facing the direction of forward travel.

2. Refer to page 34, 40 and 57 for detailed wing, centre frame drawings and wing list.

3. Place the drum shaft into the drum cross (item 27, page 34) using the three capscrews and lock

washers. (items 7, 17, page 34).

4. Place the two end caps on the drum ends using the capscrews, flats washers and lock washers

(items 8, 15, 18 and 28, page 34).

5. Use a hoist or tractor to set the completed wing (page 34) or centre frame (page 40) assembly on-

to the drum, lining up the drum lug on the frame with the drum shaft.

6. Put a good even coat of anti-seize on the drum shafts (items 25, page 34).

7. Now place the drum bearings onto the drum shafts (items 6, page 34).

8. Next, insert the four capscrews and flat washers (item 13 & 16, page 34) through the holes on the

bearing (item 6, page 34) and the frame drum lug. Place stovers on the bolts and tighten, check

torque according to torque chart.

Finishing Roller Assembly

1. Refer to page 36 for detailed drawing, if finish drum is pre-assembled make sure drum is centred

on frame and set screws are tight.

2. Unit must be in transport position to install finish roller springs.

3. Put a good even coat of anti-seize on the finish roller drum shafts.

4. Use a hoist or tractor to set the finish drum mount weldment with the finish roller drum weldment

shaft (item 1, 2 & 3).

5. Now place the drum bearings onto the drum shafts, centre in frame. (items 3 & 5).

6. Next, insert the capscrews through the holes on the bearing and the frame drum lug (items 17, 12

& 22), tighten all capscrews, stovers and set screws.

7. Attach the finish roller left and right wing attachment weldments using 5/8” x 2” capscrews and 5/8”

stover lock nuts (items 2, 9 & 11).

8. Place finish roller spring on to finish roller drum mount weldment (items 8, 19 & 23).

9. Bolt the finish roller drum mount weldment to the finish roller left or right wing attachment weld-

ment using 1” x 5” (cut to 3-3/4”) capscrew and stover lock nut (items 13 & 18).

10. Place finish roller spring tensioning weldment on the finish roller spring pin weldment (item 5 & 19).

11. Repeat for all finish roller assemblies. (5 & 7 sections only).

27

Forward Roller


Hitch (A-Frame) Assembly

1. Refer to page 38 for detailed drawing.

2. Place left and right hitch on stands approximately 30” off ground (item 1). (Ensure decals are

right side up).

3. Leave all bolts loose until directed to tighten.

4. Bolt hitch tie retainers, top and bottom pieces to hitch using capscrews, washers and stover lock

nuts (items 1, 4, 6, 15 & 20).

5. Use capscrew, stover lock nuts to connect hitch sides at the front of hitch assembly (items 16,

21 & 28).

6. Bolt hydraulic tongue and electrical holder to hitch using capscrew, washer and stover lock nut

(items 13, 15 & 24), snug these bolt.

7. Bolt hitch tongue attachment to main hitch assembly using capscrew, stover lock nut (items 18 &

23), snug these bolts.

8. Attach Perfect Hitch to hitch tongue attachment using 1” x 7” capscrew and 1” stover lock nut.

(items 23, 27 & 18), these bolts can be torqued.

9. Bolt jack tube and hydraulic mount, top and bottom, to centre section of hitch assembly using

capscrew, stover lock nut. (items 4, 5, 15, 20 & 25).

10. Place side winder jack on unit (item 9). Bolt the manual tube on to the hitch using the 3/8” x 1-

1/4” capscrew, 3/8” flat washer and 3/8” stover lock nut (items 11, 12, 13, 15 & 24).

11. The hitch assembly can now be attached to the centre frame using 3/4” x 2-1/2” capscrews and

3/4” stover lock nuts (item 1, 23 & 18). All bolts can now be torqued to specs.

Centre Frame Swing Arm Lock-Up Assembly


2. Set centre frame on level ground with the drum chocked to keep from rolling and braced frame

front and back to keep frame horizontal.

3. Make sure the walking arm and centre axles are pulled away from the centre frame.

4. Attach the hitch assembly to the centre frame, this will help stabilize the unit.

5. Remove the pins for the auto fold hook weldment. (front on centre frame).


28

Forward Roller



6. Place the auto fold hook weldment into the centre frame lugs, use auto fold pin, machinery wash-

er and cotter pin (items 3, 4, 5, 17 & 18). This will have to be matched as required with the tele-

scopic swing arm.

7. Attach the cylinder base to the centre frame lug, use cylinder pin (item 1, 3, 16 & 18).

8. Attach the cylinder stroke to the auto fold hook weldment use the cylinder pin (item 1, 4, 6, 16 &

18).

Telescopic Swing Arm Assembly


2. Begin by threading one 1/2” hex nut halfway down the threaded rod (items 3 & 12). Next, place

the tension pipe on the threaded rod, followed by the second hex nut and the 1/2” jam nut (items

6, 12 & 22). Thread the jam nut far enough so that 4 or 5 threads are visible from the jam nut to

the edge of the threaded rod (approximately 1/2”). Now tighten the hex nuts against the jam nut.

Finally, once you have everything tight; hook the tension spring on the tension rod assembly.

(Refer to pages 40 & 41).

3. Place the tension rod assembly inside the outer telescopic swing arm half, tension pipe in first

(items 2 & 3).

4. Place the inner telescopic swing arm half inside the outer telescopic swing arm half (items 1 & 2).

Insert the 1/2” x 4-1/2” capscrew through the inner telescopic swing arm half (items 10 & 22)

make sure to thread the capscrew through the spring end of the tension spring inside the

assembly. Place 1/2 stover on bolt and tighten (item 12). Be careful not to unhook the

spring prior to complete assembly.

5. Place the two 3/8” x 4-1/2” bolts (item 10) through the outer telescopic swing arm half, starting

with the bottom one these bolts will have to thread through the spring retainer pipe (item 22).

Place the bolt in angling it down, then pry the bolt up on the tension rod assembly to get it

through completely. Next place the second bolt in, followed by threading the two 3/8” stover

(item 11) onto the bolts and tightening. Pull on the assembly to make sure spring is still attached.

29

Forward Roller


Draft Arm & Telescopic Swing Arm Assembly


2. Attach draft arm pin to telescopic swing arm using pin 3/4” x 1-3/4” capscrew, spring lock washer

and flat washer (items 34, 18, 21 & 26).

3. Attach draft arm to telescopic swing arm using swing arm pin, bushing and 1” stover lock nut

(items 2, 8, 32 & 14) thread the draft arm swivel ball joint through and then tighten see #5.

4. Attach the draft arm clevis to the wing using the 3/4” x 6-1/16” x 5-3/4” inside leg length Sq. U-

Bolt and stover lock nut (items 16, 19 & 22). Refer to insert for proper location of draft arm, sizes,

clevis locations and draft clevis hole locations.

5. Attach the opposite end of the draft arm to the wing clevis using cylinder pin weldment, machine

washers, draft arm spacers and cotter pin (items 6, 24, 29 & 33).

Walking Arm / Centre Axle Assembly


2. Attach the walking arm weldment (item 3) to the centre frame using two walking arm pin weld-

ments (item 9), capscrews and stover lock nuts (items 22, 26 & 33).

3. Put a good even coat of anti-seize on the long plated walking arm pins (item 39).

4. Attach centre axle upper link weldment to the walking arm using long plated walking arm pin

(items 7, 18, 21, 30, & 39).

5. Attach walking arm hook weldment to the walking arm using long plated walking arm pin (item 7,

18, 21, 30, & 39).

6. Attach centre axle lower link weldment (item 6), lower centre axle link arm painted (item 41), and

the stroke of the 4” x 12” cylinder (item 2) to the centre axle upper link weldment (item 7) using a

1” x 7-1/2” capscrew (item 28), with 1” flat washers (item 32) between the centre axle upper link

weldment and the centre axle lower link weldments and 1” stover lock nut (item 23).

7. Attach base of 4” x 12” cylinder to the centre frame using 1” x 8-3/4” useable pin weldment (Page

38, items 9, 23 & 27).Attach centre axle weldment (item 6) to walking arm weldment (item 4) us-

ing centre axle pin weldment (item 8, 22, 26, 27, 31, 33 & 36), 3/4” x 2” capscrew, 3/4” split lock

washer, 3/4” flat washer plated.


30

Forward Roller



8. Attach centre axle weldment (item 5) to centre axle lower link weldments (item 6 & 41) using

1” x 7-1/2” capscrew and 1” stover lock nut (23 & 28).

9. Attach base of 2-1/2” x 6” cylinder to walking arm weldment (items 1 & 3) using 1” x 3-1/2”

OD cylinder pin, and two 3/16” x 2” cotter pins (items 37 & 38).

10. Attach stroke of 2-1/2” x 6” cylinder pin to walking arm hook weldment (items 1 & 4) using 1”

x 4-1/4” useable cylinder pin weldment (items 10, 34 & 37).

11. Attach two wheel and tire assemblies to centre axle weldment (items 14 & 15).

12. Attach knuckle pin weldment to walking arm weldment (items 40) using two 1/2” x 3” cap-

screws and two 1/2” stover lock nuts and flat washers (items 19, 25 & 33).

13. These cylinders will need to be adjusted, refer to page 24 for details.

Inner / Outer Wing Assembly


2. Attach the inner wing to the walking arm / knuckle assembly (items 2 & 4) Use the knuckle

pin and the 1/2” x 3” capscrew and 1/2” stover lock nut and flat washer (items 16, 18, 24 &

33).

3. Attach the light kit onto the wing using the light bracket along with the 3/8” flat washer,

3/8”spring lock washer and the 3/8” x 1” scotch grip capscrew (items 15, 20, 25 & 35).

4. Now using a forklift or overhead crane attach the inner wing assembly to the walking arm

assembly using the knuckle pins and 1/2” x 3” capscrews and 1/2” stover lock nuts and flat

washers (items 16, 18 24 & 33). All units will have this inner wing section assembly.

5. Attach claw cylinder base to inner wing or mid wing using cylinder claw pin weldment, 1” flat

washer and cotter pin (items 8, 22 & 29).

6. Attach wing hook transport lock claw weldment to inner or mid wing using 1-1/4” claw pin

weldment 1-1/4” machinery washer, 1-1/4 flat washer SAE and cotter pin (items 6, 23, 27 &

29).

7. Attach the clevis stroke end of the cylinder to the wing hook transport lock claw weldment

using 1” cylinder pin weldment 1” flat washer SAE & cotter pin (items 6, 23 & 29).

31

Forward Roller


8. Attach the wing connecting pin to the mid wing or outer wing (refer to page 57) using the con-

nex bushing, 1-1/2 ID machinery bushing, 1-1/2 ID flat washer, 3/4” flat washer, 3/4” spring

lock washer and 3/4” x 2” capscrew (items 12, 19, 21, 26, 28, 30 & 31).

9. Using a forklift or overhead crane attach the outer wing to the mid or inner wing using the

short and long finish roller pins (item 32, 34), 1/2” x 3” capscrews, and 1/2” stover lock nuts

and flat washers (items 16, 18 & 24).

10. This process will need to be repeated for F5 and F7 wing sections.

11. Refer to page 36 for finish roller details.

12. These cylinders will need to be adjusted, refer to page 23 for details.

Outer Wing / Wing Axle Assembly


2. Attach 3-1/2” x 24” cylinder base to outer wing lugs using 1” x 4-3/16” useable pin weldment

1” machine washer and cotter pin (items 2, 20 & 22).

3. Attach outer wing to wing axle assembly using 1” x 8-1/2” capscrews, 1” machine bushings,

and 1” stover lock nuts (items 1, 5, 6, 13, 16 & 20) .

4. Attach 3-1/2” x 24” cylinders clevis stroke to the wing axle assembly using 1” x 5-11/16” pin,

1” machine bushing, and cotter pin (item 1, 4, 6, 20 & 22).

5. Attach light bracket to wing using 3/8” x 1” capscrew scotch grip, 3/8” spring lock washer and

3/8” flat washer (items 14, 18, 21). Attach light assembly to light bracket (Page 50, items 9

&17) using 1/2” NF hex nut and 1/2” flat washer (items 9, 17 & 19).

6. Attach wing lock up to outer wing (items 4 & 10) using 1” x 5-1/2”capscrew and 1” stover lock

nut (items 12, 16 & 20). This can be pinned in place with a red handled safety pin c/with #9

hitch pin clip (items 10 & 23) and lock up pin c/with lynch pin (items 11 & 24).

Wing Axle Assembly


2. Attach spindle with hub to wing pivot axle using 1/2” x 4” capscrews and 1/2” stovers (items

21, 23 & 28).


32

Forward Roller



3. Put a good even coat of anti-seize on the wing pivot axle shaft, then insert the shaft into the

wing axle weldment (Item 3 & 4).

4. Place a connex bushing into wing axle weldment and 3-1/2” OD x 2-1/2” ID flat washer over

the wing pivot axle shaft (items 4, 5 & 11), then attach the slow moving sign bracket to the

wing pivot axle shaft using 1/2” x 4” capscrew and 1/2” stover lock nut (items 5, 19, 22 &

27).

5. Insert wing tee lock pin through wing axle weldment and wing pivot axle, insert #9 hitch pin

clip in tee lock pin (items 3, 4, 6 & 30).

6. Attach the slow moving sign to the slow moving sign bracket using 1/4” x 1” capscrew and

1/4” flange nuts (items 5, 15, 16 & 20).

7. Attach base end of 2-1/2” x 6” cylinder to wing axle weldment using 1” x 3-1/2” cylinder pin

and cotter pin (items 2, 29 & 31). Attach stroke end of 2-1/2” x 6” cylinder to wing pivot axle

using another 1” x 3-1/2” cylinder pin and cotter pin (items 2, 29 & 31).

8. Attach tire and rim assembly to wing pivot axle using wheel nuts (items 9, 10 & 24).

9. Mount wing wheels to wing axle assembly, torque tires according to chart, page 71.

Wing Transport Tie Bar Assembly


2. Attach the wing tie bar mount weldment to the outer wings using 3/4” x 6-1/16” x 5-3/4” U-

Bolts and 3/4” stover lock nuts (items 3, 12 & 16). Repeat for opposite wing.

3. When attaching the tie bar assembly to 10’ or 12’ outer wings the wing tie bar mount weld-

ment can capture the cross member, on the 32’ and 36’ use item # 7 part # 105-0486r1.

4. Attach wing transport tie bar to both outer wings using mount pin weldment, 1-1/4” ID ma-

chine washer, cotter pin, removable pin weldment, #9 hitch pin clip, 1/2” stover lock nuts,

1/2” x 4-1/16” x 7-1/2” U-bolt, and 1/2” transport mount lock nut weldment (items 4, 19 &

21). When unit is in transport position pin the wing transport tie bar assembly across to the

opposite wing tie bar mount weldment using the removable pin weldment and #9 hitch pin

(items 5 & 23).

5. When in field position tie bar can rest in the wing tie bar mount weldment (items 6 or 7).

33

Forward Roller



34

Forward Roller

Parts

Drum End Cap Assembly (Coupling Nut)

1

11

16

26

9

14

27

28

215

18

8

17

4

28

12

25

105

22

21

20

23

6

27

13

16

19

7

35

Forward Roller

Parts

Drum End Cap Assembly (Coupling Nut)

Item # Part # Description

1 Varies Wing Weldment

2 112-0529 Offset Drum Cross c/w Coupling Nuts

3 200-9002 Weld On Bushing

4 261-6001 Ø3-11/16” x 1-5/16” Split Tapered Bearing

5 292-4018 Ø2-7/16” Eccentric Lock Collar, Pltd.

6 292-4022 Ø2-7/16” ID 4-Bolt Flange Bearing - INA

7 525-0510 5/16” x 1-1/4” Capscrew, NC, Gr.5, Pltd.


9 526-6105 1/2” Stover Lock Nut, NC, Gr.5, Pltd.

10 526-7308 1/2” Stover Lock Nut, NC, Pltd.

11 526-7610 5/8” Stover Lock Nut, NF, Gr.8, Pltd.

12 530-0754 1/2” x 4” Capscrew, NC, Gr.8, Pltd.

13 538-1018 5/8” x 2-1/4” Capscrew, NF, Gr.8, Pltd.

14 540-0836 1/2” x 4-1/2” Socket Head Capscrew, NC, Gr.5, Black

15 550-5208 1/2” Flat Washer, Pltd.

16 550-5617 5/8” SAE Flat Washer, Gr.8 (F436), Pltd.

17 551-4905 5/16” Spring Lock Washer. Black

18 551-5008 1/2” Spring Lock Washer, Pltd.

19 802-2047 Drum Cross Mount Angle

20 805-7017 Spacer, Ø OD x .240w CDSM - 1/4”


22 805-7019 Spacer, Ø OD x .240w CDSM - 1/2


24 805-8013 Back Bushing

25 805-8023 Offset Drum Collar, Ø3-1/4” OD x .375w CDSM - 7/8”

26 Varies Drum Pipe, Ø42” x .500w Std Pipe - Varies

27 827-0017 Replaceable Drum SahftØ2-7/16” OD x 14-3/4”

28 835-1044 1/2 Section Drum End Cap

36

Forward Roller

Parts


Front

1722

7

12

3

2

18

2324

17

6

13

1

20

22

8

1521

4

11

9

19

10

11

21

16

27

14

26

11

94

1521

5

10

11

21

16

25

28

37

Forward Roller

Parts



1 105-0053r2 Wing Attachment Weldment, Left

* 105-0182r2 Wing Attachment Weldment, Right (not shown)

2 105-0054r3 Finish Drum Mount Weldment

3 105-0067 Finish Drum Weldment, Ø28” x 20” wide

4 105-0490r1 Inner Bolt On Boss Weldment, Ø1-1/2” ID x 4-7/8” overall

5 105-0510r1 Spring Tension Weldment

6 261-5104 Connex Steel Bushing, 1” ID x 1-1/4” long

7 292-4021 1-3/4” ID 4 Bolt Flange Bearing, c/w Eccentric Lock Collar

8 403-0282 Finish Roller Tension Spring, 3” OD x .562 Wire - 18-3/8” HooK to Hook

9 419-0006 1/4” Grease Zerk, NF, 90° Elbow, Pltd.

10 526-6210 5/8” Hex Nut, NC, Gr.5, Pltd.



13 526-7316 1” Stover Lock Nut ,NC, Gr.8, Pltd.

14 526-7610 5/8” Stover Lock Nut, NF, Gr.8, Pltd.

15 530-0742 1/2” x 1-3/4” Capscrew, NC, Gr.8, Pltd., Full Thread


17 530-1002 5/8” x 2”, Capscrew, NC, Gr.8, Pltd.

18 530-1640-3.75 1” x 5” Capscrew, NC, Gr.8, Pltd. (cut down to 3-3/4”)

19 546-0219 5/8” x 4” Spade Bolt

20 550-5312 3/4” SAE Flat Washer, Pltd.

21 550-5613 1/2” SAE Flat Washer, Gr.8, Pltd.

22 550-5617 5/8” SAE Flat Washer, F436 (Gr.8), Pltd.

23 556-0908 1/4” x 2” Cotter Pin, Pltd.

24 560-1211 Ø3/4” x 2-3/8” Useable, Headed Pin Pltd.

25 827-0088r2 Spring Tension Mount Pin, Ø1-1/2” x 15-5/16”, Pltd.

26 827-0091r1 Wing Connecting Pin, Ø1-1/2” x 9-3/8”, Pltd.

27 Varies Outer / Mid Wing Weldment (F5 / F7 Units)

28 Varies Inner / Mid Wing Weldment (F5 / F7 Units)

38

Forward Roller

Parts


A

DETAIL ASCALE 1:25

B

DETAIL BSCALE 1:25

C

DETAIL CSCALE 1:25

12

24

13

11

22

29

18

108

23

27

21 28

19

1716

13

24

14

7

1

6

4

9

5

51

22

29

117

3

15

6

1

20

255

15

5

25

20

6

20

28

39

Forward Roller

Parts



1* 105-0001r2 Short Hitch, Side Weldment

* 105-0002r3 Long Hitch, Side Weldment (65’ and Larger)

* 105-0122r1 Narrow Hitch, Side Weldment (Narrow Transport)

2 105-0003 Tongue Attachment Weldment

3 105-0004r2 Centre Frame Wld., Dual Bearing Hanger, c/w Auto fold (12’ wide)

* 105-0097r1 Narrow Centre Frame Wld., Dual Bearing Hanger, c/w Auto fold (10’ wide)

4 105-0037r1 Hitch, Jack Tube & Hydraulic Mount (@ 29-7/8” edge of tip & chain plate to edge)

5 105-0039 Hitch Tie Retainer c/w Hydraulic Mount

6 105-0071 Hitch Clamp c/w Hydraulic Mount

7 407-0003 24” Shepherds Hook Hose Standoff

8 409-9050 20,000 lbs. Safety Chain, Clevis Mount, Pltd.

9 420-0161 20” (15 + 5) Side Wind Parking Jack 5,000 lbs. Ø5/8” pin, (Shelby)

10 423-0001 Perfect Hitch Cushion Assembly (PP1-301VH, Refer to Page 56 for Details)

11 426-0001 Storage Tube

12 426-0002 Storage Tube Cap

* 426-0003 Storage Tube Cap and Tube Assembly



15 526-6103 3/8” Stover Lock Nut, NC, Gr.B, Pltd.


17 526-7310 5/8” Stover Lock Nut, NC, Gr.C, Pltd.


19 526-7316 1” Stover Lock Nut, NC, Gr.8, Pltd.

20 530-0609 1/2” X 1-1/2” Capscrew, NC, Gr.8, Pltd.

21 530-0742 1/2” X 1-3/4” Capscrew, NC, Gr.8, Pltd.



24 530-1656 1” x 7” Capscrew, NC, Gr.8, Pltd.



27 550-5316 1” SAE Flat Washer, Pltd.



30 839-0034 Tip and Chain holder, Painted

40

Forward Roller

Parts

Center Frame Swing Arm Lock-Up Assembly

2

11

3

8

15

13

7

15

14

19

12

1215

17

4

18

5

17

186

16

1610

1

9 618

41

Forward Roller

Parts

Center Frame Swing Arm Lock-Up Assembly


1 030-5993 Cylinder, Tie-Rod, 2-1/2" X 6" (Monarch PN 662386)

2 060-0034 Riteway Serial Number Plate

3 105-0004r2 Centre Frame Weldment, (12’ Wide)

* 105-0097r1 Narrow Centre Frame Weldment, (10’ Wide)

4 105-0012 Auto Fold Hook Weldment

5 105-0083 Auto Fold Pin, Ø1-1/4” x 6-1/4” useable, Pltd.

6 105-00857 Cylinder Pin Weldment, Ø1” x 4-1/4” useable, Pltd.

7 292-4018 2-7/16" Ø Lock Collar, Pltd. c/w set screw

8 292-4022 2-7/16" Ø - 4 - Bolt Flange Bearing

9 319-5710 1/2" ORB M x 3/8" JIC M - 90° Elbow

10 419-0004 1/4 NF Grease Jerk, Straight, Pltd.

11 510-0001 3/16” Round Head Pop Rivet,1/4” x 3/18”, Pltd.

12 526-7610 5/8" Stover Lock Nut, NF, Gr.C, Pltd.




16 554-5404 1” ID x 10 Ga., Machine Washer, Pltd.

17 554-5407 1-1/4” ID x 10 Ga., Machine Washer, Pltd.

18 556-0906 3/167” x 1-3/4” Cotter Pin, Pltd.

19 839-0014 Dual Bearing Hanger Selector Plate, Painted

42

Forward Roller

Parts


160-0039 c/with Draft Arm Pin

15

20

18

24

23

14

9

19

25

10

17

4

1

2

3

12

22

12

6

8

16

7

16

21

11

11

5

43

Forward Roller

Parts


1 105-0010 Auto Fold Arm Inner Weldment

2 105-0011 Auto Fold Arm Outer Weldment

3 105-0084 Auto Fold Swing Arm Spring Linkage

4 403-0276 Swing Arm Spring, 5/16” Wire x 2” OD x 27-1/2 Long

5 419-0100 3/8” NF Grease Zerk Straight, Pltd.

6 525-6108 1/2” Hex Jam Nut, NC, Gr.5, Pltd.

7 526-0624 3/8” x 3” Capscrew, NC, Gr.5, Pltd

8 526-0636 3/8” x 4-1/2” Capscrew, NC, NC, Gr.5, Pltd.




12 526-6208 1/2” Hex Nut, NC, Gr.B, Pltd.


14 526-7316 1” Stover Lock Nut, NC, Gr.C, Pltd.

15 530-1248 3/4” x 1-3/4 Capscrew, NC, Gr.8, Pltd.






21 805-6043 Swing Arm Collar, Offset, Painted, Ø2-1/3” OD - 3/4

22 806-2415 Spring Retainer Pipe, Ø2” ID x 3-1/2” Long, Black

23 825-0025 Swing Arm / Draft Arm Pin Bushing, Ø1-1/4” ID x 2-3/4”, Pltd.

24 827-0019r1 Swing Arm / Draft Arm Pin, Ø1-1/4” x 13-1/4”, Pltd.

23 839-0131 Slide Stopper Plate, Painted, 3/8: HR plate 2-3/4” x 4-7/8”

160-0039 c/with Draft Arm Pin


44

Forward Roller

Parts

Draft Arm & Telescopic Swing Arm Assembly

17

25

5

2810

11

4

28

15

1

3

12

20

31

13

30

23

729

18

26

21

2

8

32

14

19

9

22

16

8

6

33

33

24

29

27

34

45

Forward Roller

Parts

Draft Arm & Telescopic Swing Arm Assembly ITEM # PART # DESCRIPTION

1 105-0004r2 Centre Frame Weldment, 12’ Wide

* 105-0097r1 Centre Frame Weldment, 10 Wide (Narrow)

2 105-0010r1 Swing Arm Inner Arm Weldment

3 105-0011r1 Swing Arm Outer Arm Weldment

4 105-0069 Centre Frame Hook Roller Weldment

5 105-0078 Walking Arm Pin Weldment, Ø1-1/2” x 8-1/4” useable

6 105-0083 Wing Attachment Draft Arm Pin, Ø1-1/4” x 6-1/4” useable

7 105-0088 Centre Axle Pin, Ø1” x 8-3/4” useable

8 105-0494 Draft Arm - 237-3/8" C to C Long, F7 - 81’, 85’, 89’ (Heavy Duty)

* 105-0095r2 Draft Arm - 237-3/8" C to C Long, F5 - 58’, 62’, 68’, 74’, 78’, 84’, F7 - 77’

* 105-0094r1 Draft Arm - 171-1/8" C to C Long, F3 - 52’, F5 - 46’, 50’, 54’, F7 - 65’, 69’, 73’

* 105-0093 Draft Arm - 161-1/2" C to C Long, F3 - 42’, 46’, 48’

* 105-0474r2 Draft Arm - 153-7/8" C to C Long, F3 - 36’

* 105-0531 Draft Arm - 137" C to C Long, F3 - 32’

9 105-0511 Wing Attachment Clevis Weldment

* 105-0486r1 Wing Attachment Clevis Weldment, (F3-32 & 36)

10 419-0004 1/4” NF Grease Zerk, Pltd.

11 419-0100 3/8” NF Grease Zerk, Pltd.



14 526-6109 1” Stover Lock Nut, NC, Gr.5, Pltd.

15 526-7308 1/2” Stover Lock nut, Gr.C, Pltd.




19 546-5181 3/4” x 6-1/16” x 5-3/4” Inside Leg, U-Bolt, NC, Gr.5, Pltd.





24 550-5318 1-1/4” SAE Flat Washer, Pltd.


26 551-5012 3/4 Spring Lock Washer, Pltd.

27 554-5401 Ø1-3/4” ID x 10 Ga. Machine Washer, Pltd.

28 554-5410 Ø1-1/2” ID x 10 Ga. Machine Washer, Pltd.

29 556-0906 3/16” x 1-3/4” Cotter Pin, Pltd.

30 805-6005 Swing Arm Shaft Spacer, Ø2-1/4” OD x .240w CDSM -1/4”

31 805-6043 Offset Swing Arm Collar, Ø2-1/4” OD x .240w CDSM - 3/4”

32 825-0025 Swing Arm / Draft Arm Bushing Ø1-3/4 OD x 2-3/4 long

33 826-0006 Draft Arm Pin Bushing , Pltd. Ø1-1/4 OD x 1 long

34 827-0019r1 Swing Arm / Draft Arm Pin Ø1-1/4 OD x 13-1/4 long (Sucker Rod)

46

Forward Roller

Parts

Walking Arm / Center Axle Assembly

ATTATCH TO CENTREFRAME WALKING ARM LUG

ATTATCH TO CENTREFRAME LUG

ATTATCH TO CENTREFRAME AXLE LUG

15

29

14

10

37

933

22

8

37

3840

19

33

3

34

174

16

26

28

6

28 520

35

2413

11

12

2

7

16

41

23

18

30

39

30

21

2736

31

26

33

22

1

25

32

33

19

FRONT

47

Forward Roller

Parts, Pltd.

Walking Arm / Center Axle Assembly Item # Part # Description


2 030-5967 40THC12-175, 3/4” ORB Ports @ 90° (Monarch # 670608)

3 105-0013 Left Walking Arm Weldment, shown

* 105-0014 Right Walking Arm Weldment

4 105-0015r3 Walking Arm Hook Weldment

5 105-0016r Centre Axle Weldment c/with Bolt In Spindles

6 105-0035 Centre Axle Lower Link Weldment (x2)

7 105-0036 Centre Axle Upper Link Weldment (x2)

8 105-0074r2 Centre Axle Pin Weldment, Ø1-1/2” x 11” Useable, Tapped 3/4”, NC, Pltd.

9 105-0078r1 Walking Arm Pin Weldment, Pltd. Ø1-1/4” x 8-1/4” Useable

10 105-0087r1 Cylinder Pin Weldment, Pltd. Ø1” x 4-5/16” Useable

11 200-6011-1 812 Hub c/w Cups (CTD), Refer to Page 59 for Details

12 202-6013 Dust Cap - DC 17 (CTD)

13 203-6044 Ø2-1/2” 812 Spindle - Bolt-In, 11-3/4” Long

14* 204-5593 / 204-5586 Wheel Rim 15 x 8 - 8 Bolt (3 Section) / Wheel Rim 15 x 10 - 8 Bolt (5 Section up to 62’)

* 204-5597 Wheel Rim (5 Section 68’ and All 7 Sections)

15* 205-1181 / 205-1193 11L x 15 Tire – 12 Ply (3 Section), 12.5L x 15 Tire – 12 Ply (5 Section up to 62’)

* 205-1295 380 / 55 R 16.5 Tire - 16 Ply (5 Section 68’ and All 7 Sections)

Tire Assy 020-0130 / 020-0108 Wheel Rim 15x8–8 Bolt c/w 11Lx15 Tire – 12 Ply Assembly (3 Plex) / Wheel Rim 15x10–8 Bolt (204-5586) c/w 12.5Lx15 Tire – 12 Ply Assembly (5 Sec. up to 62’)

* 020-0136 380 / 55 R 16.5 Tire—16 Ply Tire c/w Wheel Rim (5 Plex 68’ and All 7 Plex)

16 419-0004 1/4 NF Grease Zerk, Straight, Pltd.

17 419-0006 1/4 NF Grease Zerk, 90°, Pltd.






23 526-6109 1” Stover Lock Nut, NC, Gr.B, Pltd.





28 530-1672-7.5 1” x 9” Capscrew, NC, Gr.8, Pltd. (cut to 7.5)

29 543-5563 9/16” Wheel Nut, NF, Gr.5, Pltd.

30 550-5205 5/16” Flat Washer, Pltd.


32 550-5216 1” Flat Washer, Pltd.



35 550-5615 9/16” SAE Flat Washer, Gr.8, Pltd


37 556-0906 3/16” x 1-3/4” Cotter Pin, Pltd.

38 560-1614 1” x 3-1/2” OD Cylinder Pin , Pltd.

39 827-0089 Walking Arm Linkage Pin, Ø1” x 5-11/16” Useable

40 827-0090 Knuckle Pin, Ø1-1/2” x 16-5/8, Pltd.

41 839-0074 Lower Centre Axle Link Arm Painted

48

Forward Roller

Parts

Inner / Outer Wing Assembly

18

24

16

33

11

2

35

20

25

15

14

29

22

5

7

6

23

3

13

32

31

28

12

30

2126

19

1724914

1

2718

24

1016

29

8

22

2

18

24

3416

29

16

14

11

14

4

49

Forward Roller

Parts

Inner / Outer Wing Assembly Item # Part # Description

1 * F5 / F7 Mid Wing / Outer Wing Weldment

2 * F3 Wing Weldment or F5 / F7 Outer Wing Weldment

3 030-5935 Cylinder, Tie - Rod, 3-1/2" X 8" (Monarch PN 645665)

4 105-0017 Knuckle Weldment for Ø1-1/2” Pin

5 105-0047r1 Transport Lock Weldment (Truss Claw)

6 105-0082 Transport Lock Pin Weldment (Truss Claw Pin), Ø1-1/4” x 7-9/16” Useable

7 105-0086r1 Cylinder Claw Pin Weldment, Ø1” x 7-5/16” Useable

8 105-0087 Cylinder Pin Weldment, Ø1” x 4 -5/16” Useable

9 105-0490r1 Inner bolt-In Boss Weldment, Ø1-1/2” ID x 4 -7/8” Overall

10 105-0510 Spring Tension Weldment, (Ø1-9/16” Hole Through)

11 261-5101 Connex Steel Bushing, Ø1-1/2” ID x 2” long

12 261-5103 Connex Steel bushing, Ø1-1/2” ID x 1-1/4 long

13 316-0302 1/2” ORB M x 3/8” JIC M - Adaptor

14 419-0006 1/4” Grease Zerk, NF, Pltd. 90°

15 526-2016 3/8” x 1” Capscrew, DC,Gr.5, Pltd., Scotch Grip










25 551-5006 3/8” Spring lock Washer, Pltd.


27 554-5407 Ø1-1/4” ID Machine Washer, Pltd. 10 Ga.

28 554-5410 Ø1-1/2” ID Machine Washer, Pltd. 10 Ga.

29 556-0906 3/16” x 1-3/4” Cotter Pin, Pltd.

30 805-7101 Wing Hook Roller Bearing, Ø2-3/4” x .625w CDSM - 1-1/2”

31 827-0008r3 Wing Connecting Pin, Ø1-1/2" - 7-3/8", Pltd.

32 827-0088r2 Spring Tension Mount Pin, Ø1-1/2” x 15-5/16” Overall

33 837-0090 Knuckle Pin, Ø1-1/2” x 16-5/8” Overall

34 827-0091 Wing Connecting Pin, Ø1-1/2” x 9-3/8” Overall

35 830-0305 Light Mount Bracket, Painted, 1/4” HR Plate 19” x 2”

50

Forward Roller

Parts

Outer Wing Assembly

1

22

7

2

20

17

19

9

25

142118

16

20

12 11

10

4

5

3

22

20 6

151813

8

16

20

23

24

51

Forward Roller

Parts

Outer Wing Assembly



2 105-0087r1 Cylinder Pin Weldment, Ø1"Ø x 4-3/16" Useable

3 105-0089r1 Cylinder Stroke Pin Weldment, Ø1"Ø x 5-11/16" Useable

4 105-0091 Wing Lock Up Weldment, Painted, 3/4’ x 13-13/16 long

5 Varies F3, F5 & F7 Wing Weldment

5 160-0012 Wing Axle Assembly

7 316-0302 1/2" ORB Male x 3/8" JIC Male - Adaptor

8 413-0008 Small Black Plastic Clamp

9 417-0123 Red Light Assembly, 2 Prong Female End, (Amber Light Assembly, 417-0122)

10 422-0010 Ø1" x 4-1/2" Lock Pin, Pltd. (Dynaline Red Handle)

11 422-0018 Ø1/2” x 4-1/4" Lock Up Pin, Pltd. (3-7/8” useable)

12 526-1644 1” x 5-1/2” Capscrew, NC, Gr.5, Pltd.

13 530-1678-8.5 1” x 10 Capscrew, NC, Gr.8, Pltd. (cut to 8-1/2”)

14 526-2016 3/8” x 1” Capscrew, NC, Gr.5, Pltd. Scotch Grip

15 526-6038 3/8” x 2-3/4” Capscrew, NC, Gr.5, Pltd. Scotch Grip

16 526-6109 1” Stover Lock Nut, NC, Gr.C, Pltd.

17 534-6308 1/2” Hex Nut, NF, Gr.5, Pltd.

18 550-5206 3/8" B.S. Flat Washer, Pltd.


20 550-5316 1" Machine Bushing, SAE, Pltd.


22 556-0906 3/16” x 1-3/4” Cotter Pin, Pltd.

23 558-2057 #9 Hitch Pin Clip, Pltd.


25 830-0305 Light Mount Bracket, Painted

52

Forward Roller

Parts

Wing Axle Assembly

16

15

5

20

19

27

22

26

11

3

1325

17

18

11

31

29

12

2

1024

9

7

1

8

21

4

28

23

1430

6

53

Forward Roller

Parts

Wing Axle Assembly


1 020-6014 CTD 812 Hub Assembly c/w Drive in Studs & Wheel Nuts


3 105-0056r4 Wing Axle Weldment

4 105-0058r1 Wing Pivot Axle, Bolt In Spindle Weldment

5 105-0068r1 Wing Axle Slow Moving Sign Bracket, Painted

6 123-2229 Tee Lock Pin Wld., Ø1” x 2-3/4” Useable, Pltd.

7 202-6013 CTD Dust Cap, DC 17 (CTD)

8 203-6044 812 Spindle, Ø2-1/2” x 11-3/4” long

9 204-5586 / 204-5586

Wheel Rim, 15 x 8 - 8 Bolt, 1-1/2” offset / Wheel Rim, 15 x 10 - 8 Bolt, 1-1/2” offset

* 204-5593 11L x 15 Tire-12 Ply (3 Section)

020-0130 Wheel Rim 15 x 8 – 8 Bolt c/w 11L x 15 Tire–12 Ply Assy (F3 Only)

10 205-1193 12.5L x 15 Tire-12 Ply (F5 & F7 only)

020-0108 Wheel Rim 15 x 10 – 8 Bolt c/w 12.5L x 15 Tire–12 Ply Assy (5 & 7 Sections)

11 261-5100 Connex Steel bushing, 2-3/4 OD x .121w x 2

12 319-5710 1/2” ORB M x 3/8” JIC M – 90º Elbow

13 406-0011 3” Ø x 1” Rubber Puck Stop

14 419-0004 1/4” NF Grease Zerk, Straight, Pltd.

15 424-0001 Slow Moving Sign




19 526-6105 1/2” Stover Lock Nut. NC, Gr.B, Pltd.

20 526-7104 1/4” Flange Lock Nut, NC, Gr.5, Pltd.




24 543-5563 9/16”, Wheel Nut, NF, Gr.5, Pltd.


26 550-5233 Ø2-1/2” ID Flat Washer, Pltd.



29 556-0906 3/16” x 1-3/4” Cotter Pin, Pltd.


31 560-1614 1” x 3-1/2” Cylinder Pin, Pltd.

54

Forward Roller

Parts


4

19

3

12

16

110

8

9

17

6

18

11 13

5

233

12

8

2

22

7

20

15

1416

21

Transport position

55

Forward Roller

Parts



1 105-0272 Wing Tie Bar Outer Tube Weldment

2 105-0273 Wing Tie Bar Inner Tube Weldment

3 105-0274 Wing Tie Bar Mount Weldment

4 105-0275 Mount Pin Weldment, Ø1-1/4” x 4-1/4” long

5 105-0278 Removable Pin Weldment, Ø1” x 4-1/4” long

6 105-0484 Wing Tie Bar Parking Mount Weldment (10’ & 12’ Outer Wings Only)

7 105-0486r1 Draft Arm Mount (F3-32’ & 36’ Only)

8 Varies Outer Wing Weldment, (F5 & F7 Only)

9 422-0010 Ø1” x 4-1/2” Dynaline Lock Pin

10 526-1652 1” x 5-1/2” Capscrew, NC, NC, Gr.5, Pltd.



13 526-6109 1” Stover Lock Nut, NC, Gr.B, Pltd.

14 526-7310 5/8” Stover Lock Nut, NC, Gr.C, Pltd


16 546-5181 3/4” x 6-1/16” x 5-3/4” inside leg Sq. U-Bolt, NC, Gr.5, Pltd.

17 546-5198 1/2" x 6-1/16" x 5-1/2" inside leg, Sq. U-Bolt, NC, Gr.5. Pltd.




21 556-0906 3/16” x 2” Cotter Pin Pltd.

22 558-1248 Hitch Pin Clip, Pltd.


56

Forward Roller

Parts

Perfect Hitch Assembly

The purpose of the “Perfect Hitch” is to allow the operator to always use the tractor draw pin and maintain a tight, flexible connection. The sliding V-block has a polyurethane cushion which is made to flex. The cushion also acts as a shock absorber to reduce driveline stress, giving driveline components longer life. Do not remove all the cushions! NOTE: INSTALL THE PERFECT HITCH COMPONENTS WITH BOLT HEAD ON THE BOTTOM AND

THE TOP PLATE ON TOP. Always adjust the V-block to your tractor draw pin size by following these steps.

1. Remove top plate by unscrewing ¾” bolt from bottom of Perfect Hitch and lifting top plate off.

2. The polyurethane cushion can be laid flat to achieve an extra ¼” of adjustment.

3. If more closure is needed metal spacers (not supplied) can be placed behind the cushions to

push the V-block forward and closer to the draw pin hole to tractor draw pin size. 4. Replace top plate and re-install ¾” bolt tightly (Approx. 200 ft/lb).


1 423-0005 Base Hitch (PP1-301VH)

2 423-0017 PP1-302V Top Plate Perfect Hitch

3 423-0018 PP1-203VR V-Block

4 423-0019 PP1-205H Neoprene Cushion


BOLT, HEX, INCH, GRADE 5, YELLOW ZINC PLATED1526-12245

PP1-205H NEOPRENE CUSHION2423-00194

PP1-203VR V-BLOCK1423-00183

PP1-302V TOP PLATE PERFECT HITCH1423-00172

BASE HITCH (PP1-301V3)1423-00051

DESCRIPTIONQTYPART NUMBERITEM

4

2

3

1

57

Forward Roller

Parts

Wing List All Machines & Sizes

Part # Description

105-0790 Inner Wing, Five & Seven Plex, 8 Foot, Weldment




105-0492 Mid Wing, Five & Seven Plex, 10 Foot, Weldment



105-0500 Outer Wing, Five & Seven Plex, 8 Foot, Weldment






105-0674 Outer Wing, Three Plex, 8 Foot, Weldment








58

Forward Roller

Parts

Hydraulic Clamp Details

DETAIL "A"

DETAIL "D"DETAIL "C"

3/8" FLAT WASHER

3/8" X 2-1/4"

CAPSCREW PLTD

PLASTIC CLAMP

WELDED HEX NUT

3/8" HEX NUT

3" HOSE CLAMP

WELDED HEX NUT

3/8" X 1-1/2"

CAPSCREW, PLTD. FULL THREAD3/8" X 1-3/4"

CAPSCREW PLTD

PLASTIC CLAMP

WELDED HEX NUT

3/8" FLAT WASHER

DETAIL "E"

3/8" FLAT WASHER

3/8" X 3"

CAPSCREW PLTD

PLASTIC CLAMP

WELDED HEX NUT

DETAIL "F"

3/8" FLAT WASHER

3/8" X 4"

CAPSCREW PLTD

PLASTIC CLAMP

WELDED HEX NUT

DETAIL "B"

3/8" FLAT WASHER

3/8" X 3"

CAPSCREW PLTD

PLASTIC CLAMP

WELDED HEX NUT

HOSE STACK

HOSE STACK

59

Forward Roller

Parts

Axle Details (CTD 812) Assembly # 120-1236


1 203-6044 812 Spindle, Ø2-1/2” X 11-3/4” Long, (Bolt In)

2 200-6011 CTD 812-1 (Takes SE 17)

3 201-6016 Outer Cup LM2720

4 201-6017 Inner Cup 3720

5 202-6013 DC 17 Dust Cap

6 290-6013 Outer Bearing, 2790

7 290-6014 Inner Bearing, 3780

8 295-6016 SE 17 Seal

9 534-7816 1” Castle Nut, NF, Gr.5, Black

11 554-5303 1” Spindle Washer, Black

12 556-0614 3/16” x 1-3/4” Cotter Pin, Pltd.

13 020-6014 CTD 812-1 Hub Assembly

14 543-5563 9/16” Wheel Nut, UNF

15 543-5564 9/16” Wheel Stud

60

Forward Roller

Parts

Parking Jack Assembly, Side-Handle (20” - 5000 lbs) Riteway Part # 420-0145


1 420-0018 Side Wind Crank Kit

2 420-0019 Gear Set

3 420-0020 Hitch Pin c/with Chain

4 420-0021 Screw Replacement Kit

5 420-0146 Inner Ram Assembly

6 526-0435 1/4" x 3" Capscrew, NC, Gr.5, Pltd.

7 526-7004 1/4" Lock Nut, NC, Gr.5, Pltd.

8 420-0024 Cover

9 420-0025 Body

5

4

6

1

2

8

7

3

9

61

Forward Roller

Parts

Acre Meter Details

Acre Meter Kit - Rite Way Part Number Without Acre Meter 112-0574 To Order an Acre Meter Please Call Forster Toll Free # 1-800-661-2994


1 112-0258 Acre Meter Housing (Ø4") Measure before ordering replacement meter

2 Varies Arce Meter

3 518-0608 1/2" x 1/2" Set Screw, NC, Black

4 526-0832 1/2" x 4" Capscrew, NC, Gr.5, Pltd.

5 526-7508 1/2" Stover Lock Nut, NC, Gr.5, Pltd.

6 525-6108 1/2" Jam Hex Nut, NC, Gr.5, Pltd.


8 827-0017 2-7/16"Ø x 14-3/4" Replaceable Drum Shaft

1

2

36

7

5

8

4

62

Forward Roller

Parts

Parts Details

2-1/2 X 6 MONARCH HYDRAULIC CYLINDER BREAKDOWN RITEWAY PART # 030-5993, Monarch # 662386


25TXC06-112

1 293014 Clevis Cap, 2-1/2” - 3/4” ORB

2 293017 Rod Cap, 2-1/2” - 3/4” ORB, 1-1/8” ID

3 293011 Piston, 2-1/2 - TX

4 194893 Seal Hallite 605 Rod 1-1/8

5 498512 Cylinder Tube, 2-1/2” x 6” - TX

6 494182 Tie Rod, 3/8” x 6” - TX - Washed

7 134953 Cylinder Pin, 1” x 3.37 for HP / COT

8 135995 Cotter Pin, 3/16” x 1-1/2”, Pltd.

9 148000 Set Screw, NF, 3/8” x 5/16”, Pltd.

10 293009 Rod Clevis, 1” x 1” - TX

11 128230 Hex Nut, 3/8” , NC, Gr.5, Painted

12 186562 Plug, 3/4” NF, Socket Head c/with O-ring

13 649198 Seal Kit, RK 25L-112 Lion Hyd. Rep. Kit

A A

8 16

5

9

7

23

4

10

1112

13

13

63

Forward Roller

Parts

Parts Details



35TH08-125

1 492676 Clevis Cap, 3-1/2” - 3/4” ORB

2 492677 Rod Cap, 3-1/2” - 3/4” ORB, 1-1/4” ID

3 292518 Piston, 3-1/2 - TL / TC

4 199130 Seal Wiper Rod, 1-1/4”, Metal

5 491798 Cylinder Tube, 3-1/2” x 8” - TL / TC

6 492338 Tie Rod, 5/8” x 8” - TL / TC, ASAE


8 135995 Cotter Pin, 3/16” x 1-1/2”, Pltd.


10 492652 Rod Clevis, 1-1/4” x 1” - TL / TC

11 128271 Hex Nut, 5/8” , NF, Gr.5, Painted


13 130560 Hex Nut, 1-1/4”, Lock GRB


64

Forward Roller

Parts

Parts Details

4 X 12 MONARCH HYDRAULIC CYLINDER BREAKDOWN RITEWAY PART # 030-5967, Monarch # 648381


40THC12-175

1 492680 Clevis Cap, 4” - 3/4” ORB @ 90º, 1” Cyl. Pin

2 492695 Rod Cap, 4” - 1-3/4” ID, 3/4” ORB

3 294033 Piston, 4”- 1-1/8” TH / TP - Cast

4 194897 Seal Hallite 605 Rod, Ø1-3/4”

5 467312 Cylinder Tube, 4” x 12”

6 492342 Tie Rod, 5/8” x 12”


8 135995 Cotter Pin, 3/16” x 1-1/2”, Pltd.


10 493168 Rod Clevis, 1-1/2” x 1” - Short / N



13 130559 Hex Nut, 1-1/8”, NF, Lock GRB

14 649229 Seal Kit, RK 40H-175 Lion Hyd. Rep. Kit

65

Forward Roller

Parts

Parts Details



35THC24-175

1 492676 Clevis Cap, 3-1/2” - 3/4” ORB

2 492290 Rod Cap, 3-1/2” - 3/4” ORB, 1-3/4” ID

3 258827 Piston, 3-1/2 - 1 - TSS-ISO-WR

4 437243 Rod Cyl. 1-3/4 x 24 - 1 x 1-1/2

5 491814 Cylinder Tube, 3-1/2” x 24”

6 492354 Tie Rod, 5/8” x 24”


8 135995 Cotter Pin, 3/16” x 1-1/2”, Pltd.


10 493168 Rod Clevis, 1-1/2” x 1” - Short / N


12 186562 Hex Nut, 1-1/4”, Lock GRB

13 186562 Fitting Plug, 3/4” NF, Socket Head c/with O-ring


66

Forward Roller

Parts

Lighting System

7 PIN PLUG

2 X AMBER

LENSE

1 X RED

LENSE

1

2

3

4

5

*

67

Forward Roller

Parts

Lighting System Kit (3 Plex) Riteway Part # 040-0044


1 417-0061 28’-0” Main Frame Harness Section c/w (1) 7 Plug & (2) 4 Plugs

2 417-0159 Main Wing Harness c/w (1) 32’ & (1) 16’, (1) 4 Plug & (2) 2 Plugs

3 417-0122 Amber Light Assembly (2)

4 417-0123 Red Light Assembly (2)

5 417-0150 10’ 2-Wire Extension c/w (2) 2 plugs (5 Plex only)

6 417-0151 20’ 2-Wire Extension c/w (2) 2 plugs (7 Plex only)

* 417-0170 6’ Hitch Harness Extension, c/w (1) 4 Plug and (2) 2 Plug, x2 per unit

68

Forward Roller

Hydraulic Schematic - Center Frame & Hitch

Parts

1

4 4

1

22

1818

1616

17

17

17

17

18

16

18

16

1313

12 12

15

14

15

14

HITCH

FRONT

22

22

TO LEFT WINGTO RIGHT WING

CENTER FRAME

22

22

22

17

17

21

21

21

21

F7-81 AND UP

ONLYF7-81 AND UP

ONLY

F7-8

1 A

ND

UP

ON

LY

1

21

21

21

21

1

69

Forward Roller

Parts

Hydraulic Schematic - Center Frame & Hitch



4 030-5967 Cylinder, Tie - Rod, 4" X 12" (Monarch PN 648381)

12 313-7937 Hose, Hydraulic, 3/8" Hose, 3/8" FJIC X 3/8" FJIC - 37"


14 313-7852 Hose, Hydraulic, 3/8" Hose, 3/8" MJIC X 3/8" FJIC - 52"






22 313-6701 Hose, Hydraulic, 3/8" Hose, 3/8" MJIC X 1/2" MNPT - 272"

* 313-6702 Hose, Hydraulic, 3/8" Hose, 3/8" MJIC X 1/2" MNPT - 310"

70

Forward Roller

Hydraulic Schematic - 3 Plex Wing

Parts




5 311-2066 Pipe, Hydraulic, 66 Inch, 3/8" FJIC Swivel End Fittings

* 311-2083 Pipe, Hydraulic, 83 Inch, 3/8" FJIC Swivel End Fittings








Right wing pictured, left wing similar.

2

2

1

5

8

14

13 1319

20

5

5

5

TO

CE

NT

ER

FR

AM

E

71

Forward Roller

Parts

Hydraulic Schematic - 5 Plex Wing





5,6 311-2038 Pipe, Hydraulic, 38 Inch, 3/8" FJIC Swivel End Fittings
















2

2

1

3

5

6

129

10

10

11

11

8

14

13 1319

20

5

5

5

6

66

TO

CE

NT

ER

FR

AM

E

72

Forward Roller

Hydraulic Schematic - 7 Plex Wing (up to F7-81)

Parts






5,6,7 311-2038 Pipe, Hydraulic, 38 Inch, 3/8" FJIC Swivel End Fittings















2

2

1

3

5

129

1010

11

11

8

14

1313

19

20

5

5

5

6

6

6

6

9 12

3

11

11

10 10

TO

CE

NT

ER

FR

AM

E

7

7

7

7

73

Forward Roller

Parts

Hydraulic Schematic - 7 Plex Wing (F7-81 and up)






5,6,7 311-2038 Pipe, Hydraulic, 38 Inch, 3/8" FJIC Swivel End Fittings















TO

CE

NT

ER

FR

AM

E

2

2

1

7

1010

11

11

8

14

1313

19

20

5

5

5

7

7

7

6

6

6

6

11

11

10 10

3

129

11

11

9 12

3

6

6

5

5

5

74

Forward Roller

Parts

Bolt Grade Chart

Specification Material Size Range

(inches)

Min. Proof Strength

(psi)

Min. Tensile Strength

(psi)

Min. Yield Strength

(psi)

Grade Identification

Marking

Grade 1 Low or Medium Carbon Steel

1/4 to 1-1/2 33,000 60,000 36,000

Grade 2

1/4 to 3/4 7/8 to 1-1/2

55,000 33,000

74,000 60,000

57,000 36,000

Grade 5

Medium Carbon Steel: Quenched and Tempered

1/4 to 1 1-1/8 to 1-1/2

85,000 74,000

120,000 105,000

92,000 81,000

A325 1/2 to 1

1-1/8 to 1-1/2 85,000 74,000

120,000 115,000

109,000 99,000

A325

Grade BC

Medium Carbon Alloy Steel:

Quenched and Tempered

1/4 to 2-1/2 2-1/2 to 4

105,000 95,000

125,000 115,000

109,000 99,000

BC

Grade BD 1/4 to 2-1/2 2-1/2 to 4

120,000 105,000

150,000 140,000

130,000 115,000

BD

Grade 8 1/4 to 1-1/2 120,000 150,000 130,000

Grade 8.2 Low Carbon Boron Steel: Quenched and Tempered

1/2 to 1-1/2 120,000 150,000 130,000

75

Forward Roller

Parts

Bolt Torque Chart

Nominal

Thread Size

Grade 2 Grade 5 Grade 8

Clamping

Load

Tightening

Torque

Clamping

Load

Tightening

Torque

Clamping

Load

Tightening

Torque

Coarse Thread

1/4-20 1,300 lbs 65 in-lbs 2,000 lbs 100 in-lbs 2,850 lbs 143 in-lbs


3/8-16 3,200 lbs 20 ft-lbs 4,950 lbs 31 ft-lbs 6,950 lbs 44 ft-lbs







1-8 15,000 lbs 250 ft-lbs 38,600 lbs 640 ft-lbs 54,540 lbs 900 ft-lbs

Fine Thread










76

Forward Roller

Parts

Design Layout - 3 Section

(VARIES)HITCH

(VARIES)DRAFT ARM

(VARIES)DRAFT ARM

(VARIES)CENTER FRAME

(160-0004)WALKING ARM, LEFT

(160-0005)WALKING ARM, RIGHT

(160-0012)WING AXLE

(160-0012)WING AXLE

(VARIES)WING ASSEMBLY


77

Forward Roller

Parts


(VARIES)HITCH

(VARIES)DRAFT ARM

(VARIES)DRAFT ARM

(160-0274)CENTER FRAME






(160-0012)WING AXLE

(160-0012)WING AXLE

(160-0319)FINISHING ROLLER, LEFT

(160-0320)FINISHING ROLLER, RIGHT


78

Forward Roller


Parts

(160-0002)LONG HITCH

(VARIES)DRAFT ARM

(160-0274)CENTER FRAME






(160-0012)WING AXLE

(160-0012)WING AXLE

(160-0319)FINISHING ROLLER,

LEFT


RIGHT


RIGHT





LEFT

(VARIES)DRAFT ARM

79

Forward Roller

Parts

Notes

forward roller · product. rite way manufacturing co. ltd. p.o. box 328 imperial, saskatchewan,...

Documents