Turbo Timer (R907)

Please pay attention to vehicle type!

----------------------------AT vehicle produced since 1963

If we can’t pull out key when gearshift is in P position and engine is still running, we have to release safety circuit. refer to P8 for method of release

-------------------------------------------------------------

For TOYOTA diesel engine, relay of main unit is powered when turbo timer works and ignition key is at OFF position. Battery motor of MR-2 electronic vehicle 1.10~ Highace (1.8~) and etc. runs continuously sometimes. Please refer to P8 for processing details if you want to use special adaptor LEVOC series buy separately .

------------------------------------------

Battery motor runs when ignition key is at ACC position sometimes. For vehicle without electronic fan, blue wire of turbo timer has to be connected to make battery motor runs But ACC can’t be used when turbo timer works . If vehicle (like NISSAN, ISUZU and SUBARU) has anti-fault operation relay LEVOC LVH-01/buy separately ACC can be used even turbo timer is working.

1

WARRANTY This product enjoys quality warranty in following condition:

1 Repair free of cost in warranty

In normal use, any failure caused by production in one year

after purchase is covered by warranty.

2 Repair against following problem is not free even in warranty

period.

a) Failure or damage caused by improper use, repair or

alteration.

b) Failure or damage caused by incorrect connection.

c) Failure or damage caused by water, earthquake, accidence

or fire.

d) Warranty card is not filled out with necessary information

(dealer, purchase date, customer name) or information has

been altered.

e) Can not present warranty card.

f) Open for cleaning.

11

2

Wiring method depends on vehicle type. If timer doesn’t work after installed according “Wiring of specified vehicle” or your vehicle type is not specified there, please connect according to “Wiring method 3”.

Connect according to power detection

6

Installation & Operation Manual

Thanks for purchasing Turbo Timer-R907! Please read this manual carefully to ensure a proper use.

NISSAN

TOYOTA

Battery motor operation

Operation and parts name

Parts name

Ti me se l ec t i on Switch between 1min and 3min

Digital display Flash when timer works

L.E.D power indicator When connect, it is for test When use, it is for indication

Triple-pole plug

Power ON/OFF

Accessory Clap connector

3pcs Double side adhesive 1pc

Operation SettingOperation

1.Start engine

2.Power ON

L.E.D indicator flash

ON Normally be ON OFF Be OFF when need to shut down timer and

clear its work

3.Set time by Time Selection

1min Normal situation 3min After long driving

4.Ignition OFF Turbo timer is linked with ignition switch. It starts work. If don’t pull handbrake at this moment, it stops working, engine stops running too. (handbrake detects loop)

5. Timer runs If digital remains ON in display, that shows timer is running.

Engine will be off after turbo timer runs

for programmed time

6.Engine off

Wiring Diagram

Wiring 3

Standard connection

A IG and ACC connection

SUZUKI, SUBARU MITSUBISHI, ISUZU DAIHATSU, NISSAN Key cylinder

ST battery start circuit ACC acc circuit IG ignition circuit B battery+12V

Red Yellow

Blue

Black Bolt in vehicle (grounded). Please abrase off ink on connect surface if use coated bolt

Grey Hand brake detection

ACC has electronic fan

B IG connection of system 2, ACC is not connected

TOYOTA, SUZUKI, DAIHATSU, HONDA

MITSUBISHI, MAZDA Key cylinder

ST battery start circuit ACC ACC circuit IG1 ignition electronic fan IG2 ignition system B battery+12V

Red Yellow

Blue

Black Bolt in vehicle (grounded). Please abrase off ink on connect surface if use coated bolt

Grey Hand brake detection

2systems, one for ignition, another for electronic fan Black Grounded (Refer P3) Red Power & storage circuit when key turns to OFF Blue Accessories power supplying when key turns to ACC Yellow Motor power supplying when key turns to ON Grey Hand brake detection Refer P4

www.elfinx.com FOR 12V VEHICLE ONLY

Power Switch triple plug OFF/ON

Turn power off before doing any wiring operation Connect three wires of triple plug in as following steps: 1 Use special adaptor for different vehicle type LEVOC

series Simply plug into connector. 2 Refer to “Wiring of different vehicle type” indicated in this

manual for connection. 3 Check wiring by embedded detector, then connect accordingly.

Connect black wire in for grounding to bolt at installation part. Grounded through bolt doesn’t work well sometimes. Please abrase off ink on the connecting surface if use coated bolt.

Black wire

Take off skin at the end of wire, round and fix.

3

Connect black wire of Turbo Timer to vehicle body for grounding. Connect blue wire of Turbo Timer to connector ends to detect correct connection end, switch between OFF-ACC-ON at the mean time. When have power supply, LED power indicator will be ON. Switch key to ON position and LED indicator is ON, if there are 2 more ends can turn on LED indicator except & , or key cylinder doesn’t have ACC position, please connect yellow and blue wire as following steps:

Switch key to ST position, indicator is ON when connect to yellow wire, is OFF when connect to blue wire.

Ex. Normal when there are 2ends

Black Grounding (Connector) Grey Hand brake switch

If yellow and blue wire is connected reversely, Turbo Timer will operate when switch key to ST position. If still have 2ends can turn on LED indicator when switch key to ST

position, connect these 2ends in any way, it won’t be problem.

Refer to following information for connection if vehicle has “keycylinder indication.

Red B AM AM1 AM2 Blue ACC Yellow IG Black is for grounding. If IG have IG1& IG2 two ends connect yellow and blue with

IG1 & IG2 separately. 7

Blue ACC

ACC

Yellow ON

Red OFF

Yellow ON-ST

Blue ON

Red OFF

Connect grey wire with hand brake switch. wrap connection end with plastic tape for insulation

Connect according to above picture

Turn key to ON position and test If handbrake switch wire carries 12V when release and 0V when pull up handbrake, connect this wire to detection grey wire.

Footbrake or gear detection, please operate same as above.

Wiring of specified vehicle with adaptor

Prepare adaptor for specified vehicle type LEVOC series

4

After installed, LED Power indicator will be ON when switch key to ACC or ON position, no matter turbo timer itself is switched ON or OFF.

--------------------------- AT vehicle produced since 1963

Turn off and pull out key, take off connector (blue/red and blue) extended from key lock spiratron.

Way to release safety circuit

ATTN: Gear shift of some types of vehicle is locked, you need to release gear shift locking of Nissan AT vehicle by lock release connector (LEVOC LVH-25/buy separately

Before

After

8

Wiring Diagram Wiring Diagram

Red Battery+12V Yellow Ignition circuit Blue Acc circuit

both detection and test

Black Grounded Grey Hand brake detection circuit

Picture Key cylinder � Find connector extended from key cylinder, position a and b on picture at left.

� Identify vehicle type and connector according “Wiring of different vehicle type”.

Wiring Diagram Wiring Diagram

Hand brake switch Hand brake detection thin grey wire

If there are more than 2 hand brake wires

Relative installation picture

Key cylinder Connector Adaptor for different vehicle

Connector

3P coupling joint

Hand brake switch

Key cylinder

Blue Black

Connector Connect to triple plug

Grounding

L.E.D Power indicator

Connection <pay attention to vehicle type> NISSAN

Key cylinder

Key lock spiratron Take off connector

Blue/Red Blue

TOYOTA Alteration Key cylinder Connector

Clap Connector

Wiring 1

Wiring of different vehicle type

Basic connection

5

Needn’t to take off wire skin

Connect with clap connector.

For safety please disconnect battery cathode before installation. 1 Take off wire skin 3cm length at the end of Turbo Timer wire. 2 Take off wire skin 2cm length at the end of vehicle wire. 3 Twist two ends together as above diagram. 4 Wrap the connection point tightly for insulation.

9

Warranty Card Thanks for purchasing Turbo Timer R-907!

This product has passed our factory OQC inspection. If

you meet any problem during normal use, please present this

filled card to dealer or repair center for free repair according

“warranty” condition listed out.

Product Name Turbo Timer Model# R-907

Custom

er

TEL

Address:

Name:

Vehicle Type

Purchase Date: year month date

Warranty Period: One year from purchase date

Dealer

Address:

Dealer/Shop Name: www.elfinx.com

12

Double side adhesive

Turbo Timer

Tear off paper on backside of adhesive Install Turbo Timer near to

control panel

Confirm wiring method first, then installation place.

Clean surface for affixing, adhesive tape can’t be re-used.

To ensure capability of components inside, please don’t expose

turbo timer in sunlight.

Vehicle can not run if turbo timer starts work, steering wheel will be

locked when key is pulled out.

Vehicle is in standby situation when turbo timer works.

Ensure there is no flammable article around before use.

Don’t use in a close or unventilated garage and similar place.

We don’t have duty on any dissension caused by improper use.

If vehicle carries electric fan, please check carefully whether it

works after installation. 10

Wiring Diagram Female connector

Male connector

Pay attention to connector shape!

Connect to special adaptor properly

according following key cylinder

connector picture

Adaptor bought seperately

3P Connector

Connect special adaptor to triple

connector

Wiring 2 Cut off triple plug, connect A B C wire with relative wire of connector.

Female connector

Male connector

Key cylinder

ST Battery start circuit ACC ACC circuit IG Ignition circuit B Battery+12V

Hand brake switch

Red Yellow

Blue

Black Grounded wire

Connection

Usage of clap connector

Connector

Wire near to connector (insert from left side)

Wire extended from amplifier

1. Insert wire into wire slot.

2.Press and clamp connector by plier 3. Cover and lock, then

finish connection

Other method When clap connector can’t be used

Clap connector can not be used if vehicle wire is too thick. In this case, please connect according to diagram on right side.

Vehicle wire Wire extended from Turbo Timer

Installation

Attention

Turbo Timer R-907