FleetFit

Vehicle Push-in Fittings

FleetFit vehicle push-in fittings

Air braking systems Auxiliary systems

including: exhaust braking axle lift gear changer axle ratio change throttle control speed limiters passenger doors air horns air suspension air gauges air seats

reversing aids fifth wheel levelling devices

security systems differential lock tail lift

FleetFit vehicle push-in fittings

The push-in design allows tubing joints to be made in just seconds for high productivity during vehicle manufacture, maintenance, repair and retro-fit installation

Tube assembly times can be reduced by 5 to 25 times compared with traditional compression or swaged brake fittings

Complies with Standards and Legislation world-wide including:

DOT FMVSS, SAE, TÜV, DIN, ISO, NFR

8 mm8 mm

FleetFit vehicle push-in fittings

Chamfer for easy targeting and anti kink

Body internally machined to secure the collet

Collet with multiple teeth for high grip on the tube

Lubricated ‘O’ Ring for pneumatic sealing between tube and body

Tube support to maintain firm tube grip under extreme conditions

Thread sealant coating on NPTF versions

FleetFit vehicle push-in fittings

Vacuum to 10 bar air pressure Operating temperature - 40 to +100 OC Natural finish brass body Metric have nickel plated collet and

tube support for identification Low nitrile ‘O’ Ring Roll marked collet for easy sizing Release and remake many times No tools required Available in four ranges

94 Series - Inch o/d - Metric & BSPT 95 Series - Inch o/d tube - NPTF 97 Series - Metric o/d - Metric & BSPT 98 Series - Metric o/d tube - NPTF

8 mm8 mm

Tube and fitting assembly

FleetFit

Tube preparation Use a standard tube cutter to give a square end Ensure that the tube end is clean and free from surface

damage

900

Tube and fitting assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube and fitting assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube and fitting assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube and fitting assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube and fitting assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube removal

FleetFit

Tube removal

Turn off and exhaust the pressure Push the collet in firmly and hold it there Pull the tube out and release the collet

Tube removal

Turn off and exhaust the pressure Push the collet in firmly and hold it there Pull the tube out and release the collet

Tube removal

Turn off and exhaust the pressure Push the collet in firmly and hold it there Pull the tube out and release the collet

Tube removal

Turn off and exhaust the pressure Push the collet in firmly and hold it there Pull the tube out and release the collet

FleetFit selection from the range

Selection from the range

Male straight adaptors taper and paralell

Female straight adaptors Straight connectors Bulkhead connectors and

adaptors

Selection from the range

Elbow connectors Elbow adaptors 900 Swivel adaptors 450 Swivel adaptors Female swivel nut elbow

adaptors Bulkhead elbow adaptors

Selection from the range

Tee connectors equal and unequal

Tee adaptors Tee adaptors, locking nut

and ring seal ( Hobbs ) Special bracketed

reducing tee connectors Swivel side tee adaptors

Total fittings system

Benefits of our total fittings system design service

Rationalise the quantity of fittings used

Shorten assembly time Lower cost of assembly Increase reliability Reduce potential leak

paths Reduce weight Ease stock holding Improve access Simplify testing

Dedicated fittings are designed for specific placement in systems, they provide the exact sizes at the exact angles

End