fjernstart fyr volvo

SsoI ti2006

s60 2001, s60 2002, s60 2003, s60 2004, s60 2005, s60 2006, s50 2007, s60 2008, s60 2009, s80 (-06) 1999, s80 (-06) 2000, s80 (-06) 2001,s80 (-06) 2002, s80 (-06) 2003, s80 (-06) 2004, s80 (-06) 2005, s80 (-06) 2006, s80 (07-) 2007, s80 (07-) 2008, s80 (07-) 2009, v70 (00-) 2000,v70 (00-) 2001, v70 (00-) 2002, v70 (00-) 2003, v70 (00-) 2004, v70 (00-) 2005, v70 (00-) 2006, v70 (00-) 2007,v70 (00-) 2008, v70 (00-08,2000, v70 (00-08) 2001, v70 (00-08) 2002,v70 (00-08) 2003, w0 (00-08) 2004, w0 (00-08) 2005, v70 (00-08) 2006, v70 (00-08) 2007,v70(00-08) 2008, v70 (08-) 2008, v70 (08-) 2009, v70 xc (01-) / xc70 (-07) 2001 , v70 xc (01-) / xc70 (-07) 2002, v70 xc (01-) / xc70 (-07) 2003,v70 xc (01-)/ xc70 (-07)2004, v70 xc (01-) / xc70 (-07) 2005, v70 xc (01-) / xc70 (-07) 2006, v70 xc (01-) / xc70 (-07)2007, w0 xc (01-) /xc70 2001, v70 xc (01-) | xc7o 2002, v70 xc (01-) / xc70 2003, v70 xc (01-) / xcTo 2004, v70 xc (01-) | xc70 2005, v70 xc (01-) / xc702006, v70 xc (01-) | xc70 2007, xc60 2009, xc70 (08-) 2008, xc70 (08-) 2009, xc90 2003, xc90 2004, xc90 2005, xc90 2006, xc90 2007,xc90 2008, xc90 2009

art4ltprul+Mi fii$ :::ffii;i;"'!!{:iiffi|;'.:!,!|ii of 22

,i. ] : : : : l

tt!!t!i1!{t!i!!i{t!! a!:.!:!:a..lw :t : : :t :

- l l l l : l l rq .a. . ; ; , ; " . : . " : " . ' ; , j . | .

. : , , r . ' + l l ) : , . : l -

" : - : - : : : " : : : : ' t : :

sffis w0tffi-l

ot 22

q\

WsP

W

;iii:-:::.':,#:lt:iitiip1iliiii#lwr,,..+,,,,u ot 22

;

&iy wiH8sn& sn *ris pubtidion? ftiesEa ffrxt# !ra$r nssrsst rE*6irsr. Tt]8fi& YE$l

Fubl.n*: Iss{re: Kil re:

flvnvn*nts

Fr*m:

A#re**:

-trb{apl*rne:

?do{axr

itiiEii.i;;iiiiiiiii of 22

=tt1#.ffiINTRODUCTION

F I " ' ih . i

,tB.wi!!, i,ii

NOTE! Read through the entire text before carrying outany work.

The front page gives the date of this edition and the edition itreplaces

The second page shows the tools needed for the installation andthe contents of the installation kit

The illustrations display the procedure in order of operation. Theorder of operation is repeated in the text section

Cut out the text page in order to follow the illustrations and text atthe same time.

Gars equipped with SRS/SIPS (Airbag)

Warning!

Fxtra care must be taken when wcrking on cars equippecl v.'tith $R$i$lPSair bags. This is important to prevent:

1. Personal injury

2. Oamag* to or malfuncticn of the SRSISIPS system.

Work on the SRS/$IPS sy$lems or relaied components must always becarried cut by an authorised Volvo workshcp"

ls the car equipped with SRS {supplemental restraint system}?

Cars equipped with a driver's airbag have the letters "SRS" imprinted onthe centre panel of the steering wheel. Cars equipped with drivefs andpassenger airbags are marked with "SRS" on both the steering wheelcentre panel and also on the dashboard close to the airbag.

lf the car is equipped with SIPS (side impact protection system ) a "SIPS"decal is marked on both the front seats.

Cars equipped with inflatable curtains have the marking "SRS" on one ofthe panels along the posts on the inside of the car.

Cars equipped with SRS (supplemental restraint system) also have a"SRS" decal on the front windscreen.

Do not damage the SRS wir ing!

Do not trap, fray, pierce or damage the SRS wiring. SRS wiring hasorange casing and/or is plaited.

Steering and front suspension

The contact reel in the SRS system can easily be damaged whenworking on the steering wheel, steering shaft or steering gear. Refer tothe SRS (supplemental restraint system) Service Manual or serviceinstructions in VIDA for information on carrying out such work. This is toprevent damage.

SRS warning lamp

lf the SRS waming lamp lights after repairs have been canied out, takethe car to an authorised Volvo workshop.

SRS col l ision sensor control module

s60 / w0 (00t / s80 / xc90

The collision sensor control module is located on the transmission tunnel

of 22

in the centre console, in front ofthe parking brake.

WARNING!

The air bag inflation areas must not be obstructed. Never placeany objects, such as upholstery or accessories, within theseareas. The panels must be able to deploy in the correct mannelat the r ight t ime otherwise there is a r isk of personal injury inthe event of a collision.

WARNING!

The ignition must be in position "0" and the key removed fromthe ignition if any connector in the SRS system is to bedisassembled. Then wait at least one minute. Then disconnectthe battery negative lead before disassembling any of theconnectors. When work is completed the ignit ion key must beturned to position "ll" before reconnecting the battery negativelead.

Remote start, fuel-driven heater

Note!

is accessory requires software unique to the car.

lrl... $077F709i

ot 22

i.s\ .

t\

Steps 'l-32 apply to the 560/380

Applies to the 360o Remove the cargo compartment carpet at the rear edge. First turn the two

handles (1) 90".

Steps 1-32 apply to the 560/580

Applies to the 560r Pull up the front of the cargo compartment carpet. Fold the front half back over

the rear half of the cargo compartment carpet.

Steps 1-32 apply to the S601580

Applies to the 560Slide the entire cargo compartment carpet forward slightly. Twist slightly toremove the carpet through the tailgate opening.

Applies to the S80Fold the cargo compartment carpet together. Twist the cargo compartmentcarpet slightly so that it can be removed from the cargo compartment.

Applies to 560/380Remove the carpet from the luggage compartment.

W


Press the center of the clip into the lower edge of the folding side panel on theright-hand left-hand side until a click is heard.

Remove the clios.

':.#,i ilttliit$Jii

ljjliir':r+ l=n;j;E#: r;:i::**.#PageT of22

@ VolvoCar Corporation, 2006 Prioted in Sweden

Steps 1*32 apply to the 560/580

Turn the handle (1) on the righlhand side through 90"

Fold the side panel inwards and lift it out.

a

a


Applies to the 560o Remove the weatherstrip by the C pillar panel at the rear edge of the rear door

opening.

Remove cover and screw from the top of the panel.

Pull the top edge of the C pillar panel inwards into the car (1). Fold the panelforwards (2) and lift it out.

a

a


Applies to the S80r Remove the weatherstrip by the C pillar panel at the rear edge of the rear door

openrng.

Remove the two steel clips at the front edge/upper edge of the panel.

Pull the top edge of the C pillar panel inwards into the car. Fold the panel

forwards and lift it out.

Note!

When removing the C pillar panel, do not grip it with your hand or with a tool inthe area around the lC hatch (1), as the joint function in the hatch would thenbecome deformed and it cannot be reset.

a

a

GJ VO{VOUar Uorporaqon, 4UUb i',nrueq In ri ::ll:lttnJili!:tg:tlti

1'lL1l1illitdu

'i!,!!i{tiii#:*urtf,FPageS ot22

'S.t\

\

i t l !. I rt\) i, l :t i i : I ir lr!


Applies to the S80r Unthread the belt from the belt guide.

o lnsert a hand down the side of the lower section of the side cushion- Releasethe catches while lifting the side cushion.

Steps 1-32 apply to the 560/S80

Applies to the S80o First lift the bottom edge of the short end of the cushion and then the front edge

and pull it off.

Note!

The cushion may be securely attached.

Lift out the cushion.

Check that all the clips are intact. lf not, they must be replaced.

*Applies to 560/380

o Lift the accessory electrbnic module (AEM) out of the bracket.

Disconnect the large connector from the accessory electronic module (AEM) bypressing in the catch (A) and pulling the black handle (B) in the direction of the

arrows until a click is heard.

Disconnect the connector from the accessory electronic module (AEM).

::::::;;::t;iilil!i:j:;;:;;;;ffi,@Vofuo0ar Corporation,

Page I ot 22

Remove:the black catch (1) holding the black switch in place in the connector by pulling inthe direction of the arrow.

the black switch (2) by inserting a pointed object in the hole in the other end.Press out.

o Connect the yellow cable from the control module to terminal 3 in the accessoryelectronic module (AEM) connector.

Note!

The numerical markings on the top and bottom of the black terminal pin areextremely small, so be careful when installing the cable.

Reinstall:the black switch in the connector. Lock it into place using the catch.

the connector into the accessory electronic module (AEM). Secure using theblack locking handle.

Remove the connector (1) from the accessory electronic module (AEM).

Connect the corresponding connector (2) to the T-cable for the thick cableharness, for the accessory electronic module (AEM).

Connect the remaining connector (3) on the T-cable to the connector that wasdisconnected from the accessory electronic module (AEM).

Reinstall the accessory electronic module (AEM) in its bracket.

r Clean the marked suriace on theedge using isopropanol, part no.

inside of the rear window below the panel1161721, and wipe dry.

O VolvoCar Corporaliofl; 2006 Prinled in Swedenr'' I r':tq;0?67g9;* l . ;

of22

. Press the antenna onto the inside of the windaw, as close to the panel edge aspossible.

o Tape the cable securely in place.

Pull the antenna cable through the hole for the panel's guide.

Tape the cable harness at the panel to protect it against wear from the panel'sguide.

a

a

r Secure the antenna cable (1) as illustrated

r Take the relay and the large clip from the kit.

r Press the relay into the relay holder.

r Press the clip into the relay holder.

@ VolvgGar'Corporation, 2006 Piinted in Sweden:::::.::::;= it:!.L!ii|''t:!;iii:lit;:it11tl

;:;;;. ill:l,l,tiffi!,8:jtti!{jrti!!:i... 3o7t6toe

of22

a.itltitl4jj1:

\!::.i!.:iitjilll

i y: t:i:t/,;l.ii, a,l:,

' " ' ! : ' l ' :

. Press the clip with the relay holder and relay onto the panel edge at the rearedge of the wheel arch.

o Remove the Velcro from the kit and cut it in the centre

r Press the Velcro pieces together.

r Wash the plane surface ofthe receiver unit using isopropanol P/N 1161721 andwipe dry.

:!:::!::+

iii;*.{;-9;.1=Y.s,,.4 of 22

::llL4riai&ii.ta:il:iiitiikil.i"#i;tilili

. Remove the backing from one side of the Velcro strips and press them onto thereceiver unit.

o Carefully loosen the secondary catch of the black six-pin connector from the kitusing a small screwdriver.

Connect the green (GN) cable from the kit to terminal 3, and the black (BK) cableto terminal 6 in the six pin connector.

Press the secondary catch into place on the black six pin connector.

itI!t'"i+t

a

a

a

a

a

Synchronizing the Transmitter - Receiver'I - Connect the negative baftery cable in the car.

2 - Put batteries in the trbnsmitter battery compartment.

3 - Connect the connector and antenna cable to the receiver unit.

4 - Within 5 seconds, press the "OFF" button on the transmitter until the LED goesout. Synchronization complete.

Press the receiver unit onto the Velcro on the body plate if it has loosened.

I ttotet

l l| l , , _ , ililj ililil!ii;!!'lri:ttit4.t;j.1.11/tj jiilittlttiti:ittttN)

;i;',igf:;:.1"'- li ' \a !

of 22

Tape up any cable excess from the timer relay and place next to the controlmodule under the insulation.

r Clean the marked surface on the inside of the smooth panel surface usingisopropanol, part no. 1161721, and wipe dry.

r Remove the protective backing tape from the other Velcro piece

r Press the receiver unit securely into place on the smooth surface.

r Reinstall the panels, mats, weatherstrips and seats according to the previoussteos but in reverse order.

r trltffiHt#atll4,lt1,:j!:'!t :t,i t:::.:a:.:;4;;_\tlff i i : I

": l!!:t!r:t!:t ,,,,! :ffiPage 'l4 ot 22

Programme the software in accordance with the service information in VIDA

Test the function according to the accessory manual.

a

a

*mm'.i l$lMil \ljj{ffi- 1 :i*,-" .bttba't;"i

$ffii wi=##*'"'ffiffii*

Steps 33-54 apply to the V70

o Remove both the floor hatches. Lift the rear edges of the floor hatches slightlyThen pull the hatches backwards from their mountings.


o Remove the righlhand folding panel in the cargo compartment


Remove the right side panel by first removing the cover and the screw in thefront edge.

Pull the top ofthe panel out until the clips release.

Fold the panel inwards. Lift the panel out.

a

a

. , , ' , . " . : . ; , . . . . " SOZZOZOS

. . . . . : . . .

" , -

: : : : : " ' .1:1:: . , . . , : , : . , .ovolvoeaic.oiiiiii l,,aoo$ *emffij,$$$ of 22


r Remove the small insulation panel in front of the right-hand lamp by pulling itforward at point (A).


r Remove the loudspeaker grille on the righf hand D pillar panel. First pry off thelower edge of the loudspeaker grille using a weatherstrip tool. Pull the grille outslightly and then downwards until the hooks at the top edge release.


Carefully pry up the rear roof lighting using a weatherstrip tool

Unplug the connector fom the roof lighting and move it aside.

a

a


o Remove the rear headlining panel by first removing the screw in the spacewhere the roof lighting is. Pull off the front edge of the headlining to release thefour clips. Then pull off the rear edge until the remaining clips release.

'fur- {-:

. , , . 1: :::::::::::::::::ltlirtrrilrrritrri

iii;;:,9,,,,,?.-r.ts,,,=T,,.,9 of22

, , ;


Caution!

Remove the panel in the following order otheruise the panel may b€corne damaged.

o 1 - Grip the edge and pull inward so that the clips release.

e 2 - Detach the upper edge at the window so that the panel can pass the gasstrut.

3 - Pull inward to make the clips in the opening release

4 - Lift the panel upwards.

a

a

;:"1,;A

;:::;#t*


r Lift the accessory electronic module (AEM) out of the bracket

J. ,&'\drcdtrw31d


Remove:the black catch (1) holding the black switch in place in the connector by pulling inthe direction of the arrow.

the black switch (2) by inserting a pointed object in the hole in the other end.Press out.

3S

Steps 33*54 apply io the V70

Connect the yellow cable from the control module to terminal 3 in the accessoryelectronic module (AEM) connector.

Note!

The numerical markings on the top and bottom of the black terminal pin are

extremely small, so be careful when installing the cable.

O Volvocar Corporation, 2006 Printed in $weden . ' .

Reinstall:

:::::llt:t= r,1;;i;,/':l.)titiiti";:: l':ttl1-tttff*

ot22

tr- -E*-

the black switch in the connector. Lock it into place using the catch.

the connector into the accessory electronic module (AEM). Secure using theblack locking handle.


Remove the connector (1) from the accessory electronic module (AEM).

Connect the corresponding connector (2) to the T-cable for the thick cableharness, for the accessory elechonic module (AEM).

Connect the remaining connector (3) on the T-cable to the connector that wasdisconnected from the accessory electronic module (AEM).

Reinstall the accessory electronic module (AEM) in its brackefu r-

ffiffif"'"#


r Clean the marked surface on the inside of the rear side window below the paneledge using isopropanol, part no. 1161721, and wipe dry.


o Press the antenna onto the inside of the window, as close to the panel edge aspossible.

o Clamp the cable at the existing cable harness. i

i*: of 22

$iilifl#r#'i.i:

*


o Take the relay and the large clip from the kit

o Press the relay into the relay holder.

o Press the clip into the relay holder.


o Press the clip with the relay holder and relay inside the panel edge in front of therighthand rear lamp.


o Carryoutsteps2l-27.


o Clean the marked surface on the rear end of the dghthand vent. Useisopropanol, part no. 1161721, and wipe dry.


o Remove the protective backing tape from the other Velcro piece.

:::t:iilhii:;t:'

t1 ;' . . 1 ;

' ' i '@ VolvoCar Cofporation, 2006Printed in $ra'eden ,, :

.,tl


r Press the receiver unit securely into place on the rear end of the right.hand vent


r Reinstall the panels, mats, and covers according to the previous steps but inreverse order.


o Programme the software in accordance with the service information in VIDA

r Test the function according to the accessory manual.

Steps 55 - 62 apply to XC90

Remove the two centre floor hatches by lifting them slightly and then pulling themaway from their mountings at the front edge. lf the rear centre floor hatch isequipped with grocery bag holder on the underside then the floor hatch issecured with a belt on each short side of the storage box. These must bedetached.

r Removethe storage box.

... :llill lirlll:l llll ,

6ffi1.v,q$$ti'$.1o.;;ii .ilrt,i:::;gt17,liiiii,i,iti:::;:'::#


Applies to cars with three rows of seats and integrated carrier bagholder on the underside of the centre f loor hatchFold up the centre rear floor hatch (1 ).

Detach the two straps on the underlying panel. Lift up the rear edge of the panel,fold the floor hatch back and lift out the floor hatch with the panel.

Applies to cars with three rows of seats without an integrated carr ierbag holderLift up the centre rear floor hatch at the rear edge and lift it out.

Applies to al l modelsRemove the righthand side floor hatch (2).


Applies to cars with two rows of seatso Remove the front storage box.


o Remove the folding side panel from the right-hand side of the cargocomDartment.

Steps 55 - 62 apply to XG90

r Carefully pull off the top edge of the right-hand D pillar panel. Continue down untilthe three clios have released.

Remove the panel by pulling it straight up and unhook it from the side panel. lfapplicable, disconnect the connector for the D pillar loudspeaker.

O VolvoCar Corporation, 20O6 Prinled in Sweden , '-i-i' , l',liill|i"fi ,"#,tf :W of 22

: : : . 1 ; : : : : I.,,".,. .




o Carry out steps 42-54.

.!::WffiF* ot 22

fjernstart fyr volvo

Documents