fit handbook english
TRANSCRIPT
-
8/3/2019 FiT Handbook English
1/28
Handbook
on tHe MalaysianFeed-in tariFF
For tHe ProMotion
oF renewableenergy
-
8/3/2019 FiT Handbook English
2/28
2
Salam 1Malaysia. As a commitment towards the growth of renewable energy in
the country, the Ministry of Energy, Green Technology and Water had presentedbefore the Parliament for the first reading of the Renewable Energy (RE) Bill in
December 2010. At the time of printing of this handbook, the Bill is ready for the
second and third reading. Once the Bill is passed in Parliament, the new Act will
enable the implementation of the Feed-in Tariff (FiT) in Malaysia, starting from the
middle of 2011. Through this Renewable Energy Act, the total renewable energy
capacity in the country is expected to increase significantly from 61.2 MW today to
at least 985 MW by 2015, and 2,080 MW by 2020.
This handbook on the Malaysian Feed-in Tariff (FiT) is published to address the influx
of enquiries that my Ministry had received over the past six months. The objective
of the handbook is to provide official information on the FiT which my Ministry will
implement via the Sustainable Energy Development Authority of Malaysia (SEDA
Malaysia). SEDA Malaysia is anticipated to be legally established as a statutory body
by April 2011, once the SEDA Bill is passed.
The Renewable Energy Bill which I hope will be openly discussed and subsequently
passed by Parliament this year, will catalyse Malaysias aspiration to become a leader
in green technology, and meet our target of 40% carbon emissions intensity
reduction by 2020. Renewable Energy is also a key component in the Economic
Transformation Programme (ETP), in realizing our vision for Malaysia to become a
high income nation.
YB Dato Sri Peter Chin
Minister of Energy, Green Technology and Water
March 2011
F O R E W O R D
-
8/3/2019 FiT Handbook English
3/28
3
This handbook has been prepared to disseminate information on the Feed-in Tariff
(FiT) mechanism and its application to promote the use of Renewable Energy inMalaysia. The earlier part of the handbook comprises of the vision and objectivesof the Renewable Energy Policy and Action Plan followed by information on the FiTmechanism. The FiT rates, targets and application for the FiT are on the later part ofthis handbook. Efforts have been made to ensure that the contents in this handbookare relevant to local situations and practices.
The information in this handbook had been crafted to be practical and simple to
follow. Whilst every attempt has been made to ensure the accuracy and relevanceof the facts and figures given in the handbook, users are advised to check and verifythe application of any information, data, and Renewable Energy installationcontained herein with respect to their particular situation and environment.
The Ministry of Energy, Green Technology and Water wishes to express our gratitudeand appreciation to the following for their direct contribution in the preparation ofthe RE Bill and the subsidiary legislations: Attorney Generals Chamber (AGC),Ministry of Finance (MOF), Central & States Economic Planning Units, Ministry ofScience, Technology and Innovation (MOSTI), Ministry of Natural Resources andEnvironment (MNRE), Ministry of Plantation, Industries and Commodities (KPPK),Ministry of Housing and Local Government (KPKT), Energy Commission (ST), thePerformance Management & Delivery Unit (PEMANDU), Malaysian InvestmentDevelopment Authority (MIDA), Malaysian Palm Oil Board (MPOB), Tenaga NasionalBerhad (TNB), Sabah Electricity Sdn Bhd (SESB), Akademi Sains Malaysia (ASM), RE
industry players and associations, building industry and professional associations,financial institutes, institution of higher learning/research institutes, consumerassociations, non-Government organizations (NGOs), members of the media andthe rakyat at large.
Datuk Loo Took GeeSecretary General, Ministry of Energy, Green Technology and Water
March 2011
P R E F A C E
-
8/3/2019 FiT Handbook English
4/28
TOP SOIL CAP METHANE
WELLWELLTRASH
CLAY LINER
LEACHATES
-
8/3/2019 FiT Handbook English
5/28
Hdk h Myi fd-i triff
r h Prmi Rw ergy
t a b l e o f C o n t e n t sForeword 2
Preface 3
Table of Contents 5
Important Notice 6
National RE Policy and Action Plan 7
The Concept of Feed-in Tariff 9
Rationale for Feed-in Tariff 10
Positive Impact of Feed-in Tariff 12
Verification of Feed-in Tariff Effectiveness 13
Critical Success Factors for Feed-in Tariff 14Funding for Feed-in Tariff 15
Features of Feed-in Tariff 18
RE Capacity Targets under Feed-in Tariff 20
Administration of Feed-in Tariff 22
Application for Feed-in Tariff 21
Impact to Existing RE Generators 23
The Socio-Economic Impact of Feed-in Tariff On Malaysia by 2020 24References 25
APPENDICES: Feed-in Tariff Rates 26
-
8/3/2019 FiT Handbook English
6/28
6
Important Notice
The information provided in this handbook is set within the context of renewableenergy. The Ministry of Energy, Green Technology and Water has compiled this
information in good faith and information in this handbook may change without
prior notice due to the on-going legislative process of passing the Renewable
Energy Bill in the Parliament. The information provided in this handbook is indicative
of our renewable energy policies to be implemented and it should not be used as
the sole basis for any commercial decision on RE investments.
-
8/3/2019 FiT Handbook English
7/28
7
National RE Policy and Action Plan
Renewable Energy (RE), in the context of the Renewable Energy Act, refers toelectricity generated from recurring and non-depleting indigenous resources.
The Ministry of Energy, Green Technology and Water (KeTTHA) is responsible to
formulate policies and strategies, as well as undertake planning for electricity supply
in the country. The development of electricity supply industry (ESI) is guided by the
National Energy Policy (1979), the Four Fuel Diversification Policy (1981), and the
Fifth Fuel Policy (2001). On the 2nd
April 2010, the Cabinet approved the NationalRenewable Energy Policy and Action Plan (NREPAP) that would be the cornerstone
for a more aggressive renewable energy deployment in the country. The policy and
objectives of the NREPAP are:
The Policy Vision
Enhancing the utilisation of indigenous renewable energy resources tocontribute towards national electricity supply security and sustainable socio-
economic development.
The Objectives
i. To increase RE contribution in the national power generation mix;
ii. To facilitate the growth of the RE industry;
iii. To ensure reasonable RE generation costs;iv. To conserve the environment for future generation; and
v. To enhance awareness on the role and importance of RE.
Under the National RE Policy and Action Plan, five strategic thrusts have been
identified to achieve the five objectives. The strategic thrusts which are
represented in Figure 1, are as follows:
i. Thrust 1: Introduce an appropriate regulatory framework;
ii. Thrust 2: Provide a conducive environment for RE businesses;
iii. Thrust 3: Intensify human capital development;
iv. Thrust 4: Enhance RE research and development; and
v. Thrust 5: Design and implement an RE advocacy programme.
-
8/3/2019 FiT Handbook English
8/28
8
Thrust 1 forms the foundation which the other remaining strategic thrusts are builtupon. Strategic Thrust 1 involves the enactment of the Renewable Energy Act which
mandates the implementation of the feed-in tariff (FiT) mechanism. While the FiT is
instrumental in increasing energy security in the country, the remaining strategic
thrusts are vital to ensure a holistic approach towards a sustainable RE socio-
economic development.
National RE Policy and Action Plan
RE PolicyVision & Objectives
Strategic Thrust 5: Advocacy Programme
Strategic Thrust 1: Foundation: RE Law
Strategic Thrust 2:
Conducive RE
Business
Environments
Strategic Thrust 3:
Human Capital
Development
Strategic Thrust 4:
RE R&D
Action Plan
Vi
Business
e REonduciv
egic Thrust 2:traS
lopment
ion & Objec
vDe
apitalHuman C
egic Thrust 3:raS
o c
es
tion PlancA
RE R&D
egic Thrust 4:traS
iv
vironmentsEn
tion:oundagic Thrust 1: Fttra aE L
Figure 1: Action Plan & Strategic Thrusts
-
8/3/2019 FiT Handbook English
9/28
9
Feed-in tariffs (FiTs) oblige distribution licensees (DLs) to buy from feed-in approvalholders (FIAHs) the electricity produced from renewable sources and sets the FiT
rate. The DLs would pay for each unit of the renewable electricity supplied to the
electricity grid for a specific duration.
By guaranteeing access to the grid and setting a favourable price per unit of
renewable electricity, the FiT mechanism would ensure that RE becomes a viable
and sound long-term investment for companies, industries, and also for individuals.The key concepts under the FiT mechanism are as follows:
Distribution licensees: Companies holding the licence to distribute electricity
(e.g. TNB, SESB, NUR).
Feed-in Approval Holder: An individual or company who holds a feed-in
approval issued by SEDA Malaysia, and the holder is eligible to sell electricity
from renewable resources.
FiT rate: Fixed premium rate payable for each unit of electricity sold to
distribution licensees. The FiT rate differs for different RE technologies and
installed capacities. Bonus FiT rate applies when the criteria for bonus
conditions are met.
Indigenous: Renewable resources must be from within Malaysia and are notimported from neighbouring countries.
Duration: Period of which the renewable electricity could be sold to
distribution licensees and paid with the FiT rate. The duration is 16 years for
biomass and biogas, and 21 years for small hydro and solar PV. The duration
is decided based on characteristics of the renewable resources and
technologies.
The Concept of Feed-in Tariff
-
8/3/2019 FiT Handbook English
10/28
10
Rationale for Feed-in Tariff
In designing an effective policy mechanism to drive RE deployment in Malaysia, thefollowing criteria need to be considered carefully:
A simple approach which does not depend on a combination of many
support mechanisms;
Promotes maintenance and continued operation of the systems;
Offers long term support, allowing for secured environment to promote
domestic and foreign investments;
An approach that is effective and efficient;
The Ministry of Energy, Green Technology and Water had conducted a thorough
study on the effectiveness of major RE policy instruments practised globally. The
findings of the study showed that FiT is the most effective RE policy mechanism in
promoting and sustaining RE growth. The findings were drawn from past
experiences learnt from other countries and studies from international energy policy
experts. These renowned experts have studied and concluded that the FiTs have
been proven to be the best support mechanisms to rapidly increase the share of
renewable energy production and use (Mendonca, Jacobs & Sovacool 2010; World
Future Council 2011).
Success Story: Germany leads as a role model in nationwide implementation of the
FiT policy. The FiT has generated over 300,000 renewable energy employment in
Germany and the trend indicates employment to increase to 400,000 by 2020
(REN21 2010). The German renewable energy industry has a turnover of over 30billion of which a large share is due to RE technology exports.
Advantages of FiT: FiT addresses two primary economic issues faced by many
countries: employment and gross national income via RE industry growth. The two
secondary issues addressed by FiT are: energy security and climate change
mitigation. The FiT also provides solutions to tertiary issues concerning social health,
empowering and providing fairer wealth distributions to citizens and thecommunity, and environment conservation. All this is achieved without putting a
strain on the Governments budget and spending. Table 1 shows some of the
economic, political, social and environmental advantages of the FiTs.
-
8/3/2019 FiT Handbook English
11/28
11
Rationale for Feed-in Tariff
Economic i. Green jobs creation
ii. Create FDIs and DDIs for manufacturing and export
iii. Hedge against conventional fuel price volatility
iv. Provide RE investor security
v. Drive economic development
vi. Create stable conditions for market growth
vii. Simple, transparent policy structure helps encourage
new start-ups and innovators
Political i. Demonstrate commitment to RE deployment
ii. Increase energy security and autonomy
iii. Promote a more decentralized and democratized form of
electricity system
iv. Create mechanism for achieving RE and emissions-
reduction targets
v. Increase the stakeholder base supporting RE policies
Social i. Fairer wealth distribution and empower citizens and
communities
ii. Increased public support for renewables through direct
stake and increased exposure to renewables
iii. Encourage citizen and community engagement in
activities protecting climate and environment
iv. Make RE a common part of the landscape and cityscape
Environmental i. Reduce carbon emission and pollutions
ii. Encourage energy efficiency measures
iii. Reduce dependency on fossil fuels
Table 1: Advantages of the FiTs
(Source: Mendonca et al 2010)
-
8/3/2019 FiT Handbook English
12/28
12
Positive Impact of Feed-in Tariff
Compared to other renewable energy policies, the Feed-in Tariff mechanism has thehighest number of countries adopting it. By early 2010, there were at least 50
countries and 25 states/provinces adopting the feed-in tariff policy instrument. In
contrast, only 50 states/provinces/countries are implementing the renewable
portfolio standard (RPS), and even much lesser numbers ascribing to other policies
such as capital subsidies, investment tax credits, tradeable certificates, and others
(REN21 2010).
Previous studies on renewable energy policies have concluded that FiTs are more
effective compared to other RE policy mechanisms (see the following section on
Verification of FiTs Effectiveness). Mendonca and his colleagues (2010) cited the
four main reasons for FiT superiority as follows:-
ii. FIT is able to drive down capital cost and achieve RE technology price
reduction much faster compared to other RE policies.
ii. FIT promotes a diversified portfolio of technologies and industrial sectors.
Unlike some other RE policies which instigate price competition among RE
technologies, FiT encourages harmonious growth of a variety of RE
technologies which are in congruence with the countrys indigenous
renewable energy resources.
iii. FIT minimizes electricity cost in two ways: the guaranteed tariff lowers therisk of RE investment and, therefore reduces the cost of capital investment.
In addition, the degression feature of the FiT reduces opportunistic windfall
profits and encourages efficiency, as well as lowers manufacturing costs over
time.
iv. FIT encourages market competition among manufacturers in lowering RE
technology pricing, leading to better market conditions for RE investors tobuild and deploy RE projects.
-
8/3/2019 FiT Handbook English
13/28
13
Verification of Feed-in Tariff Effectiveness
1) Stern, N. (2007): The Economics of Climate Change - Stern Review, Part IV: PolicyResponses for Mitigation
The Stern Report on the financial costs of global climate change was published
by the former chief economist of the World Bank, Nicolas Stern. Part IV of the
report (Policy Responses for Mitigation) gives a short overview of the existing
incentives for renewable energy projects and differentiates between price-based
(e.g. FiT Laws) and quantity-based (e.g. Tradable Green Certificates) supportmechanisms. It argues that both have proven to be effective in the past but
existing experience favours price-based support mechanisms (p. 366) and a
comparison of tradable quotas and feed-in tariffs reveals that the latter achieves
larger deployment at lower costs (p. 366).
2) Federal Environmental Agency (2006): Monitoring and evaluation of policy
instruments to support renewable electricity in EU Member States - Final Report
The report compares feed-in tariffs and quota systems (Tradable Green
Certificates (TGCs) / Renewable Portfolio Standards (RPS)). In this respect, the
report concluded that feed-in tariffs (FiTs) have been successful in triggering a
considerable increase of RE technologies in almost all the countries in which
they have been introduced and where their effectiveness was not significantly
hampered by major barriers (administrative barriers, grid access, etc.) (p. 88). In
addition, the report states that the risk premium required by investors can beminimised by the high level of price security given by feed-in tariffs, thus
lowering the overall costs for consumers and assuring relatively homogenous
premium costs for society over time (p. 88).
3) United Nations Development Programme (2008): Promotion of Wind Energy
Lessons Learned From International Experience And UNDP-GEF Projects, Chapter
1: Public Policies
The report stated that feed-In tariff policies have been very effective in Germany,
Spain and Denmark, leading to the worlds first, second and fifth installed wind
energy capacities. France and Portugal have also used Feed-in Tariffs to become
fast growing wind energy countries with 810MW and 695MW respectively,
installed in 2006. This resulted in them to occupy 10th and 9th place in terms of
installed capacity (p. 16).
-
8/3/2019 FiT Handbook English
14/28
14
Critical Success Factors for Feed-in Tariff
FiT is considered a successful RE policy instrument as it is the only policy thatmaintains minimal transaction costs, promotes RE diversification and manageability
of electricity prices in the long run. However, the success of FiT in any country
depends on several critical factors:
i. Access to the grid is guaranteed utilities are legally obliged to accept all
electricity generated by RE producers.
ii. Local approval procedures are streamlined and clear.
iii. FiT rates must be high enough to produce a return on investment, plus
reasonable profit (not excessively) to act as an incentive.
iv. FiT rates should be fixed for a period (typically 20 years) to give certainty
and provide businesses with clear investment environment.
v. Adequate "degression" for the FiT rates to promote cost reduction to achieve
grid parity
vi. Adequate fund should be created to pay for the FiT costs and guarantee the
payment for the whole FiT contract period.
vii. The design of the FiT must be customized to suit contextual conditions ofthe country.
viii. Implementation by a competent body in a professional manner that includes
constant monitoring, progress reporting and transparency.
Capping of the FiT: In many countries where the FiT is enacted, caps on RE installed
capacities are highly discouraged as these caps limit RE growth and constrain itsimpact (Hans-Josef 2009). The avoidance of such caps is possible in countries where
electricity tariff is deregulated. However, in a regulated electricity market such as in
Malaysia, the funding source for FiT is limited to a fixed percentage imposed on the
utilitys electricity revenue. Therefore, caps are essential to ensure that there would
be adequate fund to pay for the FiT costs. Once the electricity market in Malaysia is
deregulated, or when FiT has been operating for a considerable period of time, then
removal of the caps would be conceivable.
-
8/3/2019 FiT Handbook English
15/28
15
Funding for Feed-in Tariff
The question everyone wants to know is who pays for the FiTs? The most commonmethod for funding the FiT involves sharing the costs amongst the end-users
(electricity consumers). This method would result in a very small increase in price
of electricity paid by the electricity consumers, but at the same time the consumers
could benefit from revenues derived from the RE generation. In this respect, FiT is
not a subsidy but a cost pass-through mechanism for renewable power generation.
The FiT in Malaysia is not financed from tax revenue. Instead, the FiT will be financedby a RE Fund which is derived by passing the FiT cost to final electricity consumers.
However, the passing of this cost is limited to only 1% of the total electricity revenue
generated by the utilities (e.g. TNB). Nonetheless, 56% of the utilitys customers who
consume less than 200 kWh (equivalent to RM 43.60) per month will be exempted
from contributing to this RE fund. Therefore, the heavy consumers of electricity
would contribute more to the RE fund. This is essentially a polluters pay concept
the ones who pollute the most, pays the most to the RE Fund. This form of fund
collection has been proven to be an effective tool in overcoming current economic
and financial crisis as it does not utilise public funds. The spin-off from this RE Fund
mechanism is a greater acceptance for the consumers to adopt energy efficiency
measures to reduce their electricity consumptions.
Financial Governance of the RE Fund: The management of the RE Fund will be
under the supervision of SEDA Malaysia. The RE Fund can only be used for the
purpose of disbursing the FiT payment claims made by the distribution licensees,and to cover any administrative expenses relating to the FiT implementation. The
FiT payment claim by the distribution licensees is depicted in Step 4 of Figure 2,
which shows the steps in the RE Fund process flow. Measures on financial
governance of the RE fund include transparency in disclosing and publishing of
financial reports on funding receipts, funding disbursement to Feed-in Approval
Holders, and the administrative fees payable to the distribution licensees and SEDA
Malaysia. The accounts of the RE Fund will be presented to Parliament on annualbasis, as mandated under the Renewable Energy Act.
-
8/3/2019 FiT Handbook English
16/28
16
Funding for Feed-in Tariff
Electricity bills 100%(after tariff revision which
incorporates 1% of RE Fund)
Power Utilities
Residental
Sector
Commercial Sector Industrial
Sector
Solar BIPV buildings
Residental
Sector
Commercial Sector Industrial
Sector
Solar BIPV buildings
(RE Fund 1%)
Figure 2: RE Funding Flow for FiT
Step 1: Electricity consumers pay electricity bills to distribution licensees (e.g. TNB)
Step 2: One percent of electricity revenue is channelled from distribution licensees
to RE Fund which is managed by SEDA Malaysia
Electricity bills 100%(after tariff review)
Power Utilities(Revenue 99%)
RE Fund(SEDA Malaysia)
-
8/3/2019 FiT Handbook English
17/28
17
Funding for Feed-in Tariff
Solar BIPV buildings
Electricity bills 100%(after tariff review)
Power Utilities(Revenue 99%)
RE Fund(SEDA Malaysia)
SREP Developers
(FiT payments)
Residental
Sector
Commercial Sector Industrial
Sector
Residental
Sector
Commercial Sector Industrial
Sector
{(FiT - displacedcost) + fee}
Step 3: Distribution licensees make FiT payment to FiAHs
Step 4: Distribution licensees claim from RE Fund, the positive sum of differential
between FiT payments and the prevailing displaced cost, including an
administrative fee.
Solar BIPV buildingsSREP Developers
Electricity bills 100%(after tariff review)
Power Utilities(Revenue 99%)
RE Fund(SEDA Malaysia)
-
8/3/2019 FiT Handbook English
18/28
18
Features of Feed-in Tariff
The FiT rates are categorized by RE technologies, installed capacities and bonusFiT rates. The FiT rates for some RE technologies will decline each year according to
their respective degression rates. The FiT rate for each RE installation is determined
by the Commercial Operation Date (COD). The duration of the FiT is effective once
the COD has been achieved.
The key features of the FiT are as follows:
RE technologies: biomass (inclusive of municipal solid waste), biogas
(inclusive of landfill/sewage), small hydro and solar photovoltaic. The
rationale for selecting these RE technologies are based on proven
technologies and technical potentials under the local environment.
Degression Rates: The level of the FiT rate applicable to RE systems
installed in the future will decrease with time, according to annual
degression rates. The degression occurs at the start of each newcalendar year. Thus, RE systems that are commissioned in later years
will have lower FiT rate. However, the FiT rate within the duration of
the REPPA will not degress anymore. The basis of degression rate is
that the cost of RE technologies, just like any other technologies, is
expected to drop as the technologies mature. The degression rate
therefore reflects the maturity and the existing cost reduction
potential of each RE technology.
REPPA: REPPA stands for the Renewable Energy Power Purchase
Agreement which is a legal contract between the potential FiAHs (RE
developer) and DLs (eg. TNB, SESB, etc). REPPA is dependent upon on
the RE technology and installed capacity.
Installed capacity: For all RE technologies, the maximum installedcapacity is 30 MW. The FiT rate for any RE technologies will decline as
installed capacities increase due to cost optimisation from economies
of scale.
-
8/3/2019 FiT Handbook English
19/28
19
Features of Feed-in Tariff
Bonus FiT rates: Additional FiT rates will be given for those RE systemsthat satisfy the conditions for bonus criteria.
Commercial Operation Date: The date when the RE system is
officially connected to the electricity grid.
The FiT rates for the different RE technologies are shown in the Appendix. The quota
for FiT is shown in Table 2 .
Other RE technologies: Initially, solar thermal, wind, and geothermal, will not be
offered under the FiT, as the technical potential of these resources have yet to be
ascertained empirically. However, the Minister is empowered to change the
Schedule of the RE Act, whereby the basis of inclusion of other RE technologies in
the Act rests with the resources and technical potentials, as well as the economic
viability of the RE projects under the local condition.
FiT Rate designed to facilitate Grid Parity: The feed-in tariff in Malaysia is designed
with the main objective of achieving grid parity, which will happen when the
subsidy for fossil fuel is gradually removed, and/or when all external costs of fossil
fuel power generation are taken into consideration, or when RE technologies
become cheaper. Grid parity occurs when the cost of generating renewable
electricity is equivalent (or lower) than the cost of generating electricity from
conventional fossil fuel and/or nuclear energy. Once grid parity is achieved, FiAHswould be paid based on the prevailing displaced cost for the remaining REPPA
duration.
The RE Act accommodates for changes in the future and such changes may apply
to inclusion of new RE technologies and revision of degression rate for the FiT.
-
8/3/2019 FiT Handbook English
20/28
20
RE Capacity Targets under Feed-in Tariff
Year Biogas Biomass Solid Waste SmallHydro Solar PV TOTAL
2011 20 110 20 60 9 219
2012 35 150 50 110 20 365
2013 50 200 90 170 33 543
2014 75 260 140 230 48 753
2015 100 330 200 290 65 985
2016 125 410 240 350 84 1,209
2017 155 500 280 400 105 1,440
2018 185 600 310 440 129 1,664
2019 215 700 340 470 157 1,882
2020 240 800 360 490 190 2,080
2025 350 1,190 380 490 455 2,8652030 410 1,340 390 490 1,370 4,000
Table 2: Cumulative RE Capacity Targets (MW)
-
8/3/2019 FiT Handbook English
21/28
21
Application for Feed-in Tariff
Application form: Application for FiT can be done both manually and online viaSEDA Malaysias official website. Application forms will be made available on the
authoritys website and printed copies will be made available at SEDA Malaysias
office.
Jumping the FiT queue: There is no preferential treatment for FiT applications.
Instead all FiT applications will be treated fairly and equally through a transparent
application process. An online FiT application system is expected to be availablefrom Q3 2011.
Monopolizing of RE Quota: During submission of application for the FiT, an eligible
producer will be required to submit their work plan. Once the Feed-in-Approval is
granted, SEDA Malaysia will monitor closely each project until COD is achieved. This
close monitoring is required in order to prevent FiAH from monopolizing the RE
quota. This monitoring is important as once a FiT application has been approved,
the RE fund will automatically be deducted and allocated to the approved FiTapplicant (FIAH). The RE quota is revised with the reduced RE Fund availability.
In order to avoid any monopolizing of RE quota, SEDA Malaysias online system will
track the RE projects milestone via the submitted work plan. If any delays are
detected, a notice will be sent to the FiAH to request for an explanation of the delay.
If the FiAH fails to respond satisfactorily, then the FiA will be revoked. When that
happens, the fund committed to the FiAHs will be released, and this will return theallocated quota to the system. This is to prevent any abuse of the FiT system and to
allow other interested parties opportunity to apply for the FiT.
Existing Fiscal and Financial Incentives: FiAH is entitled to fiscal incentive on
respective merits in addition to the FiT.
Offence and Penalty: Any falsification of information, failure to comply, attemptsto contravene or obstruct the RE Law by the FiAH or DL is considered an offence
and upon conviction shall be liable to a penalty.
Ad i i i f F d i T iff
-
8/3/2019 FiT Handbook English
22/28
22
Administration of Feed-in Tariff
The FiT will be administered and managed by Sustainable Energy DevelopmentAuthority of Malaysia (SEDA Malaysia). SEDA Malaysia is a statutory body to be
formed under the SEDA Act once the Bill is passed in Parliament.
The official website of SEDA Malaysia will be http://www.seda.gov.my and is
envisaged to be available by April 2011. Until then, all FiT communications will be
carried out under the website of MBIPV Project, http://www.mbipv.net.my .
SEDA Malaysia office will be located at:
Level 9, No. 29, Lot 4C11
Jalan P4B, Persiaran Perdana
62570 Presint 4
Putrajaya, MALAYSIA
I t E i ti RE G t
-
8/3/2019 FiT Handbook English
23/28
23
Impact on Existing RE Generators
SREP refers to the Small Renewable Energy Power Programme started in May 2001by the (then) Ministry of Energy, Communications and Multimedia (now known as
Ministry of Energy, Green Technology and Water).
Conversion of SREP to FiT: SREP holders are eligible to convert their SREP to FiT
once the latter has been implemented. But the existing SREP holders will need to
apply for the FiT and re-sign a new REPPA. Thus, they are required to terminate their
existing REPPA signed under the SREP programme. However, the conversion of SREP
to FiT is not compulsory. Any SREP developers who wishes to remain under SREP is
free to do so.
Consequences On duration: The existing SREP holders duration for FiT will be
adjusted accordingly, taking into account the number of years their plants have
generated electricity for commercial sale to the distribution licensee. For example,
if the biomass plant has been operating under SREP programme for 5 years from
COD, then upon conversion from SREP to FiT, the duration for REPPA under FiT willbe reduced by 5 years. In this case, the original duration for biomass under FiT is 16
years, but the reduction of 5 years will result in a revised duration of 11 years only.
Consequences On Energy Payment Rate: Upon conversion, the qualified FiT rate
for the RE plant will be based on the COD date. Each new calendar year will reduce
the existing FiT rates by their respective degression rate (as shown in the FiT Rates
tables in the Appendix). However, once COD is achieved, the FiT rate is not affectedby the degression.
The Socio Economic Impact of Feed in Tariff on Malaysia by 2020
-
8/3/2019 FiT Handbook English
24/28
24
The Socio-Economic Impact of Feed-in Tariff on Malaysia by 2020
Impact on Green Employment: A minimum of 52,000 jobs are expected to becreated to construct, operate and maintain RE power plants.
Impact on Business Revenue: A minimum of RM 70 billion of RE business revenues
is projected to be generated from RE power plants operation, which will generate
tax income of minimum RM 1.75 billion to Government. In short, the revenue from
FiT is considered a taxable income.
Impact on Loan Value: A minimum of RM 19 billion worth of loans is estimated to
be generated for RE projects, which will provide banks with new sources of
revenues.
Impact on CO2 avoidance:The FiT can, on a cumulative basis, avoid 42 million and
145 million tonnes of CO2 from the power generation sector by 2020 and 2030,
respectively. This can be achieved when the country generates at least 2,080 MW
and 4,000 MW (see Table 2) of RE capacities by 2020 and 2030, respectively, throughthe FiT.
Impact on Externality Cost on CO2 avoidance: Minimum of RM 2.1 billion in savings
of external cost is expected to be generated to mitigate CO2 emissions (total 42
million tonnes avoided from 2011 to 2020, on the basis of RM 50 per tonne of
external cost).
Impact on Countrys Image: Malaysia is perceived as a country with a global social
responsibility and bears its share to mitigate climate change. In addition, the
Government is perceived as being responsible to ensure energy security and
autonomy, so the countrys economy is resilient and sustainable in the long run.
References
-
8/3/2019 FiT Handbook English
25/28
25
References
Hans-Josef Fell. 2009. Feed-in Tariffs for Renewable Energies.http://www.mbipv.net.my/dload/FIT.pdf
Interim website for Malaysian FiT information.
http://www.mbipv.net.my/content.asp?higherID=0&zoneid=6&categoryid=
34 (until April 2011)
Klein, A., Held, A., Ragwitz, M. Resch, G. & Faber, T. 2008. Evaluation of Different FiT
design Options, best practice for the international Feed-in Cooperation.
http://www.futurepolicy.org/fileadmin/user_upload/PACT/Learn_more/Klei
n_et_al.__2006_.pdf.
Miguel Mendonca, David Jacobs, Benjamin Sovacool. 2010. Powering the Green
Economy: The Feed-in Tariff handbook. Earthscan: UK & USA.
Ministry of Energy, Green Technology and Water Malaysia. 2010. FAQ on MalaysianFiT. http://www.mbipv.net.my/FAQs%20on%20FiT.pdf
Ministry of Energy, Green Technology and Water Malaysia. 2010. National RE Policy.http://www.mbipv.net.my/dload/National%20RE%20Policy %202010%20-
%20ExecSum.pdf
Official website for Sustainable Energy Development Authority (SEDA) Malaysia.
http://www.seda.gov.my/ (effective April 2011)
Official website for World Future Council on Feed-in Tariffs: a policy solution for
renewable energy. http://www.futurepolicy.org/renewable energy.html
REN21. 2010. Renewables 2010. Global Status Report.
http://www.ren21.net/Portals/97/documents/GSR/REN21_GSR_2010_full_re
vised%20Sept2010.pdf
Renewable Energy Bill 2010.
http://www.parlimen.gov.my/files/billindex/pdf/2010/DR472010E.pdf.
Sustainable Energy Development Authority Bill 2010.
http://www.parlimen.gov.my/files/billindex/pdf/2010/DR432010E.pdf.
APPENDICES: Feed-in Tariff Rates
-
8/3/2019 FiT Handbook English
26/28
26
APPENDICES: Feed in Tariff Rates
Capacity of renewable energy installation FiT rate(RM per kWh) Effective periodAnnual
degression rate
Installed capacity up to and including 4 MW 0.32 16 years 0.50%
Installed capacity above 4 MW, and up to and
including 10 MW
0.30 16 years 0.50%
Installed capacity above 10 MW, and up to andincluding 30 MW 0.28 16 years 0.50%
Additional for use of gas engine technology with electricalefficiency of above 40% +0.02 16 years 0.50%
Additional for use of locally manufactured orassembled gas engine technology +0.01 16 years 0.50%
Additional for use of landfill or sewage gas as fuel source +0.08 16 years 1.80%
Table 3: FiT rates for Biogas
APPENDICES: Feed-in Tariff Rates
-
8/3/2019 FiT Handbook English
27/28
27
APPENDICES: Feed in Tariff Rates
Capacity of renewable energy installation FiT rate(RM per kWh) Effective periodAnnual
degression rate
Installed capacity up to and including 10 MW 0.31 16 years 0.50%
Installed capacity above 10 MW, and up to andincluding 20 MW 0.29 16 years 0.50%
Installed capacity above 20 MW, and up toand including 30 MW 0.27 16 years 0.50%
Additional for use of gasification technology +0.02 16 years 0.50%
Additional for use of steam-based electricity generatingsystems with overall efficiency of above 14% +0.01 16 years 0.50%
Additional for use of locally manufactured or assembledgasification technology +0.01 16 years 0.50%
Additional for use of municipal solid waste as fuel source +0.10 16 years 1.80%
Table 4: FiT rates for Biomass
Capacity of renewable energy installation FiT rate(RM per kWh)Effective
periodAnnual
degression rate
Installed capacity up to and including 10 MW 0.24 21 years 0%
Installed capacity above 10 MW, and up to andincluding 30 MW 0.23 21 years 0%
Table 5: FiT rates for Small Hydro
APPENDICES: Feed-in Tariff Rates
-
8/3/2019 FiT Handbook English
28/28
28
APPENDICES: Feed in Tariff Rates
Capacity of renewable energy installation FiT rate(RM per kWh) Effective periodAnnual
degression rate
Installed capacity up to and including 4 kWp 1.23 21 years 8%
Installed capacity above 4 kWp, and up to and including24 kWp 1.20 21 years 8%
Installed capacity above 24 kWp, and up to and including72 kWp 1.18 21 years 8%
Installed capacity above 72 kWp, and up to and including1 MWp 1.14 21 years 8%
Installed capacity above 1 MWp, and up to and including10 MWp 0.95 21 years 8%
Installed capacity above 10 MWp, and up to andincluding 30 MWp 0.85 21 years 8%
Additional for installation in buildings or buildingstructures +0.26 21 years 8%
Additional for use as building materials +0.25 21 years 8%
Additional for use of locally manufactured or assembledsolar photovoltaic modules +0.03 21 years 8%
Additional for use of locally manufactured or assembledsolar inverters +0.01 21 years 8%
Table 6: FiT Rates for Solar Photovoltaic